Antifouling enhancement of poly(vinylidene fluoride) microfiltration membrane by adding Mg(OH)2 nanoparticles

Investigation of the Biosafety of Antibacterial Mg(OH)2 Nanoparticles to a Normal Biological System

The toxicity of Mg(OH)₂ nanoparticles (NPs) as antibacterial agents to a normal biological system is unclear, so it is necessary to evaluate their potential toxic effect for safe use. In this work, the administration of these antibacterial agents did not induce pulmonary interstitial fibrosis as no significant effect on the proliferation of HELF cells was observed in vitro. Additionally, Mg(OH)₂ NPs caused no inhibition of the proliferation of PC-12 cells, indicating that the brain's nervous system was not affected by Mg(OH)₂ NPs. The acute oral toxicity test showed that the Mg(OH)₂ NPs at 10,000 mg/kg induced no mortality during the administration period, and there was little toxicity in vital organs according to a histological analysis. In addition, the in vivo acute eye irritation test results showed little acute irritation of the eye caused by Mg(OH)₂ NPs. Thus, Mg(OH)₂ NPs exhibited great biosafety to a normal biological system, which was critical for human health and environmental protection.

The enhancement of dye filtration performance and antifouling properties in amino-functionalized bentonite/polyvinylidene fluoride mixed matrix membranes

Trade-off issue and membrane fouling remain two major issues in the utilization of membrane technology for the water treatment due to reduced membrane permeability and lifetime. In our study, we employed 3-aminopropyltriethoxysilane modified bentonite (BNTAPS) as an anti-fouling modifier to prepare polyvinylidene fluoride (PVDF)-based membranes via the phase inversion method. The effects of BNTAPS concentration on the physical, mechanical, morphological, and filtration performance of the hybrid membranes have been investigated. It was found that the addition of BNTAPS improved the hydrophilicity of the membrane revealed by the decreased water contact angle. Consequently, the pure water flux of PVDF membrane containing 0.5% BNTAPS (PVDF/BNTAPS0.5%) increased to 35.5 L m^-2 h^-1. Moreover, the PVDF/BNTAPS membrane showed a smaller pore diameter and porosity compared to pristine PVDF. The membrane performance evaluation was carried out using cationic and anionic dyes, i.e., methylene blue (MB) and acid yellow (AY17), respectively. Our study revealed that the rejection of each dye was slightly increased for the PVDF/BNTAPS0.5%. However, the flux recovery rate of the PVDF/BNTAPS membrane significantly improved, which directly prolonged the membrane lifetime.

Solvent-Free One-Pot Synthesis of Epoxy Nanocomposites Containing Mg(OH)2 Nanocrystal-Nanoparticle Formation Mechanism

Epoxy nanocomposites containing Mg(OH)₂ nanocrystals (MgNCs, 5.3 wt %) were produced via an eco-friendly "solvent-free one-pot" process. X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), and thermogravimetric analysis (TGA) confirm the presence of well-dispersed MgNCs. HRTEM reveals the presence also of multisheet-silica-based nanoparticles and a tendency of MgNCs to intergrow, leading to complex nanometric structures with an intersheet size of ∼0.43 nm, which is in agreement with the lattice spacing of the Mg(OH)₂ (001) planes. The synthesis of MgNCs was designed on the basis of a mechanism initially proposed for the preparation of multisheet-silica-based/epoxy nanocomposites. The successful "in situ" generation of MgNCs in the epoxy via a "solvent-free one-pot" process confirms the validity of the earlier disclosed mechanism and thus opens up possibilities of new NCs with different fillers and polymer matrix. The condition would be the availability of a nanoparticle precursor soluble in the hydrophobic resin, giving the desired phase through hydrolysis and polycondensation.

Green Synthesis of Silver Nanoparticles as an Effective Antibiofouling Material for Polyvinylidene Fluoride (PVDF) Ultrafiltration Membrane

Silver nanoparticles (AgNPs) were successfully synthesized using the aqueous extract of the Paronychia argentea Lam (P. argentea) wild plant. The results showed that the conversion of Ag⁺ to Ag⁰ nanoparticles ratio reached 96.5% as determined by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), with a negative zeta potential (ζ) of −21.3 ± 7.68 mV of AgNPs expected to improve the stability of synthesized AgNPs. AgNP antibacterial activity has been examined against Streptococcus aureus (S. aureus) and Escherichia coli (E. coli) bacteria. The minimum inhibition concentration (MIC) was 4.9 µL/mL for both E. coli and S. aureus bacteria, while the minimum bactericidal concentrations (MBC) were 19.9 µL/mL and 4.9 µL/mL for S. aureus and E. coli, respectively. The synthesized AgNPs were incorporated in ultrafiltration polyvinylidene Fluoride (PVDF) membranes and showed remarkable antibiofouling behavior against both bacterial strains. The membranes were characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), and X-ray diffraction (XRD). The contact angle and porosity of the membrane were also determined. The efficiency of the membranes regarding rejection rate was assessed using bovine serum albumin (BSA). It was found in the flux experiments that membranes BSA rejection was 99.4% and 98.7% with and without AgNPs, respectively.

Nanometals-Containing Polymeric Membranes for Purification Processes

A recent trend in the field of membrane research is the incorporation of nanoparticles into polymeric membranes, which could produce synergistic effects when using different types of materials. This paper discusses the effect of the introduction of different nanometals such as silver, iron, silica, aluminum, titanium, zinc, and copper and their oxides on the permeability, selectivity, hydrophilicity, conductivity, mechanical strength, thermal stability, and antiviral and antibacterial properties of polymeric membranes. The effects of nanoparticle physicochemical properties, type, size, and concentration on a membrane's intrinsic properties such as pore morphology, porosity, pore size, hydrophilicity/hydrophobicity, membrane surface charge, and roughness are discussed, and the performance of nanocomposite membranes in terms of flux permeation, contaminant rejection, and antifouling capability are reviewed. The wide range of nanocomposite membrane applications including desalination and removal of various contaminants in water-treatment processes are discussed.

Polymer Nanocomposite Ultrafiltration Membranes: the Influence of Polymeric Additive, Dispersion Quality and Particle Modification on the Integration of Zinc Oxide Nanoparticles into Polyvinylidene Difluoride Membranes

This study aims to improve the understanding of the influence of metal oxide nanofillers on polyvinylidene difluoride (PVDF) ultrafiltration membranes. Zinc oxide nanoparticles were chosen as the model filler material. The membranes were prepared by non-solvent induced phase separation from PVDF solutions in N-methylpyrrolidone. The influences of the addition of polyvinylpyrrolidone (PVP), the nanoparticle dispersion quality, and a surface modification of the ZnO particles with PVP on the nanofiller integration into the polymer matrix and the resulting membrane separation performance, were evaluated. Unmodified and PVP-modified nanoparticles were characterized by evaluation of their Hansen solubility parameters. The membranes were characterized by ultrafiltration experiments, scanning electron microscopy (SEM) and with respect to mechanical properties, while the dope solutions were analyzed by rheology in order to judge about dispersion quality. Pure water permeability and solute rejection data revealed that the dominant effect of the addition of pristine ZnO nanoparticles was a major decrease in permeability caused by pore blocking. In SEM analyses, it was seen that the plain nanofiller did not integrate well into the polymer matrix. Importantly, it was found that the surface modification of the nanofiller, as well as a high dispersion quality, can be strategically used to enhance the integration of the nanofiller and thus suppress pore blocking, leading to membranes with high ultrafiltration rejection and permeability simultaneously. Overall, the study provides relevant insights into a new approach to integrating nanofillers into polymer nanocomposite membranes for improving their properties and performance.

A, Ismail AF. Permeability and Antifouling Augmentation of a Hybrid PVDF-PEG Membrane Using Nano-Magnesium Oxide as a Powerful Mediator for POME Decolorization

This study focused on developing a hydrophilic hybrid polyvinylidene fluoride (PVDF)-polyethylene glycol (PEG) hollow membrane by incorporating Nano-magnesium oxide (NMO) as a potent antifouling mediator. The Nano-hybrid hollow fibers with varied loading of NMO (0 g; 0.25 g; 0.50 g; 0.75 g and 1.25 g) were spun through phase inversion technique. The resultants Nano-hybrid fibers were characterized and compared based on SEM, EDX, contact angle, surface zeta-potential, permeability flux, fouling resistance and color rejection from palm oil mill effluent (POME). Noticeably, the permeability flux, fouling resistance and color rejection improved with the increase in NMO loading. PVDF-PEG with 0.50 g-NMO loading displayed an outstanding performance with 198.35 L/m2·h, 61.33 L/m2·h and 74.65% of water flux, POME flux and color rejection from POME, respectively. More so, a remarkable fouling resistance were obtained such that the flux recovery, reversible fouling percentage and irreversible fouling percentage remains relatively steady at 90.98%, 61.39% and 7.68%, respectively, even after 3 cycles of continuous filtrations for a total period of 9 h. However, at excess loading of 0.75 and 1.25 g-NMO, deterioration in the flux and fouling resistance was observed. This was due to the agglomeration of nanoparticles within the matrix structure at the excessive loading.

Multifunctional PVDF/CNT/GO mixed matrix membranes for ultrafiltration and fouling detection

Membrane fouling can be effectively addressed by modifying the membrane to realize anti-fouling capability together with real-time fouling detection. Here, we present the synthesis and water treatment testing of a promising candidate for this application, a composite membrane of polyvinylidene fluoride (PVDF) and functionalized carbon nano-materials prepared by a facile phase inversion method. The synergistic effect of oxidized multi-walled carbon nanotubes (OMWCNTs) and graphene oxide (GO) enabled better surface pore structures, higher surface roughness, hydrophilicity, and better antifouling property as compared with that of pristine PVDF membranes. The PVDF/OMWCNT/GO mixed matrix membranes (MMMs) achieved a high water flux of 125.6 L m^-2 h^-1 with high pollutant rejection rate, and their electrical conductivity of 2.11 × 10^-4 S cm^-1 at 100 kHz was sensitive to the amount of pollutant uptake. By using hybrid MMMs, we demonstrate simultaneous pollutant filtering and uptake monitoring, which is an important step in revolutionizing the water treatment industry.

Controlling the Antimicrobial Action of Surface Modified Magnesium Hydroxide Nanoparticles

Magnesium hydroxide nanoparticles (Mg(OH)2NPs) have recently attracted significant attention due to their wide applications as environmentally friendly antimicrobial nanomaterials, with potentially low toxicity and low fabrication cost. Here, we describe the synthesis and characterisation of a range of surface modified Mg(OH)2NPs, including particle size distribution, crystallite size, zeta potential, isoelectric point, X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), energy dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM). We explored the antimicrobial activity of the modified Mg(OH)2NPs on the microalgae (C. reinhardtii), yeast (S. cerevisiae) and Escherichia coli (E. coli). The viability of these cells was evaluated for various concentrations and exposure times with Mg(OH)2NPs. It was discovered that the antimicrobial activity of the uncoated Mg(OH)2NPs on the viability of C. reinhardtii occurred at considerably lower particle concentrations than for S. cerevisiae and E. coli. Our results indicate that the antimicrobial activity of polyelectrolyte-coated Mg(OH)2NPs alternates with their surface charge. The anionic nanoparticles (Mg(OH)2NPs/PSS) have much lower antibacterial activity than the cationic ones (Mg(OH)2NPs/PSS/PAH and uncoated Mg(OH)2NPs). These findings could be explained by the lower adhesion of the Mg(OH)2NPs/PSS to the cell wall, because of electrostatic repulsion and the enhanced particle-cell adhesion due to electrostatic attraction in the case of cationic Mg(OH)2NPs. The results can be potentially applied to control the cytotoxicity and the antimicrobial activity of other inorganic nanoparticles.

Quaternized Amphiphilic Block Copolymers/Graphene Oxide and a Poly(vinyl alcohol) Coating Layer on Graphene Oxide/Poly(vinylidene fluoride) Electrospun Nanofibers for Superhydrophilic and Antibacterial Properties

Poly(vinylidene fluoride) (PVDF) is common polymer for electrospinning, however, its high hydrophobicity is a major drawback, which cause fouling. To introduce hydrophilicity and antibacterial activity, quaternary ammonium-functionalized amphiphilic diblock copolymers were synthesized and blended with a PVDF/graphene oxide (GO) solution, then, electrospun and coated with a hydrophilic polymer, poly(vinyl alcohol) (PVA). The amphiphilic block copolymer, consisting of a hydrophobic poly(methyl methacrylate) block and a hydrophilic poly[N,N-2-(dimethylamino)-ethyl methacrylate) block (PMMA-b-PDMAEMA), was synthesized. Polymeric quaternary ammonium with three different alkyl chain lengths (C₂, C₄, and C₈) were successfully introduced to obtain as q-PMMA-b-PDMAEMA. The q-PMMA-b-PDMAEMA in the nanofiber matrix was confirmed by C=O bands (1734 cm⁻¹) in the Fourier transform infrared spectra. Nano-sized spherical protuberances were distributed on the surface as revealed by field emission scanning and transmission electron microscopies. The PVDF/GO/q-PMMA-b-PDMAEMA@PVA nanofibers has superhydrophilic properties (water contact angle = 0–20°) and the pure water flux was generally improved by increasing the alkyl chain length. When introducing the longest alkyl chain (C_8,OBC), the total fouling ratio was the lowest (49.99%) and the bacteria removal capacities after 60 min were the highest for both Escherichia coli (4.2 × 10⁵ CFU/mg) and Staphylococcus aureus (6.1 × 10⁵ CFU/mg) via growth inhibition and cytoplasmic membrane damage.

Development of in situ synthesized Y-based nanoparticle/polyethersulfone adsorptive membranes by adjusting the composition of the coagulation bath for enhanced removal of fluoride

The composition of coagulation bath significantly altered the membrane structure, composition and adsorption performance for defluoridation by affecting the phase inversion kinetics.

Hydrophilic modification and anti-fouling properties of PVDF membrane via in situ nano-particle blending

Two hydrophilic poly-vinylidene fluoride (PVDF) ultrafiltration membranes were prepared via in situ embedment of nanoparticles (NP), i.e., TiO₂ and Al₂O₃, respectively, and their anti-organic-fouling and anti-biofouling were comprehensively investigated. Characterization of modified PVDF-NP membranes by XRD and FTIR exhibited that nanoparticles were embedded successfully. Series of fast filtration tests demonstrated that in contrary to virgin PVDF membrane, PVDF-NP membranes have high permeability and anti-organic-fouling ability by decreasing the possibility of organic matters deposition and accumulation. Co-existed Ca²⁺ in feed solution deteriorated the organic fouling in virgin PVDF and PVDF-NP membranes, which was mainly caused by gelation of macromolecular foulants. PVDF-NP membranes were used to form MBR modules for domestic wastewater treatment, and the long-term monitoring evidenced that hydrophilic modified membranes achieved stably high COD and [Formula: see text] rejection efficiencies, and better organic rejection capability than mAO process. PVDF-NP membranes possessed consistently high anti-biofouling ability to maintain stable membrane permeability.

Preparation of CuONPs@PVDF/Non-Woven Polyester Composite Membrane: Structural Influence of Nanoparticle Addition

Membrane distillation techniques have appeared as promising options for guaranteeing the availability of potable water in times of scarcity of this essential resource. For membrane preparation, polyvinylidene fluoride (PVDF) is preferred due to the easier synthesis procedures, with respect to other fluorine-based polymers. In this work, copper oxide nanoparticles (CuONPs) of different weight percent (wt %) embedded in PVDF membranes supported on non-woven polyester fabric (NWPET) were prepared by the phase inversion method, and characterized by spectroscopy (ATR-FTIR, Raman) and electron microscopy techniques (SEM). The PVDF deposited onto the NWPET was mostly composed of its polar β-phase (F(β) = 53%), which was determined from the ATR-FTIR spectrum. The F(β) value remained constant throughout the whole range of added CuONP concentrations (2–10 wt %), as was determined from the ATR-FTIR spectrum. The absence of signals corresponding to CuONPs in the ATR-FTIR spectra and the appearance of peaks at 297, 360, and 630 cm⁻¹ in the Raman spectra of the membranes suggest that the CuONPs are preferably located in the inner PVDF membrane, but not on its surface. The membrane morphologies were characterized by SEM. From the obtained SEM micrographs, a decrease and increase in the amount of micropores and nanopores, respectively, near the surface and intercalated in the finger-like layer were observed. As a result of the CuONP addition, the nanopores in the sponge-like layer decreased in size. The values of water contact angle (WCA) measurements showed a decreasing trend, from 94° to 80°, upon the addition of CuONPs (2–10 wt %), indicating a diminishment in the hydrophobicity degree of the membranes. Apparently, the increase in the amount of nanopores near the surface decreased the membrane roughness, so it became less hydrophobic.

Fabrication of anti-fouling PVDF nanocomposite membranes using manganese dioxide nanospheres with tailored morphology, hydrophilicity and permeation

Manganese dioxide (MnO₂) nanospheres were prepared by a facile hydrothermal technique and their influence on the permeation and antifouling properties of poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes was investigated.

Colloid particle formulations for antimicrobial applications

Colloidal particles are being extensively studied in various antimicrobial applications due to their small size to volume ratio and ability to exhibit a wide spectrum of antibacterial, antifungal, antialgal and antiviral action. The present review focuses on various nanoparticles (NPs) of inorganic, organic and hybrid materials, and discusses some of the methods for their preparation as well as mechanisms of their antimicrobial action. We consider the antimicrobial applications of metal oxide nanoparticles (ZnO, MgO, CuO, Cu₂O, Al₂O₃, TiO₂, CeO₂ and Y₂O₃), metal nanoparticles (NPs), such as copper, silver and gold, metal hydroxide NPs such as Mg(OH)₂ as well as hybrid NPs made from biodegradable materials, such as chitosan, lignin and dextran, loaded with other antimicrobial agents. Recent developments for targeted delivery of antimicrobials by using colloid antibodies for microbial cell shape and surface recognition are also discussed. We also consider recent advances in the functionalization of nanoparticles and their potential antimicrobial applications as a viable alternative of conventional antibiotics and antiseptic agents which can help to tackle antimicrobial resistance. The review also covers the recently developed environmentally benign NPs (EbNPs) as a "safer-by-design" green chemistry solution of the post use fate of antimicrobial nanomaterials.

Recent progress in the synthesis of nanostructured magnesium hydroxide

This highlight discusses magnesium hydroxide design at the nanoscale, common aspects of crystallite growth and how nanostructuring impacts properties.

Tailored PVDF nanocomposite membranes using exfoliated MoS2 nanosheets for improved permeation and antifouling performance

Exfoliated molybdenum disulfide (E-MoS₂) nanosheets were synthesized from bulk MoS₂.

A Novel Polyvinylidene Fluoride Tree-Like Nanofiber Membrane for Microfiltration

A novel polyvinylidene fluoride (PVDF) tree-like nanofiber membrane (PVDF-TLNM) was fabricated by adding tetrabutylammonium chloride (TBAC) into a PVDF spinning solution via one-step electrospinning. The structure of the prepared membranes was characterized by field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and pore size analysis, and the hydrophilic property and microfiltration performance were also evaluated. The results showed that the tree-like nanofiber was composed of trunk fibers and branch fibers with diameters of 100-500 nm and 5-100 nm, respectively. The pore size of PVDF-TLNM (0.36 μm) was smaller than that of a common nanofiber membrane (3.52 μm), and the hydrophilic properties of the membranes were improved significantly. The PVDF-TLNM with a thickness of 30 ± 2 μm showed a satisfactory retention ratio of 99.9% against 0.3 μm polystyrene (PS) particles and a high pure water flux of 2.88 × 10⁴ L·m-2·h-1 under the pressure of 25 psi. This study highlights the potential benefits of this novel PVDF tree-like nanofiber membrane in the membrane field, which can achieve high flux rates at low pressure.

Performance and antifouling enhancement of polyethersulfone hollow fiber membranes incorporated with highly hydrophilic hydroxyapatite nanoparticles

Membrane fouling is one of the main drawbacks in water purification applications. The present work indicated that the fabricated HAp/PES hollow fiber membranes presented better hydrophilicity, permeation and anti-fouling performance compared to PES membranes.

Fabrication and characterization of a polysulfone-graphene oxide nanocomposite membrane for arsenate rejection from water

BACKGROUND

Nowadays, study and application of modified membranes for water treatment have been considered significantly. The aim of this study was to prepare and characterize a polysulfone (PSF)/graphene oxide (GO) nanocomposite membrane and to evaluate for arsenate rejection from water.

MATERIALS AND METHODS

The nanocomposite PSF/GO membrane was fabricated using wet phase inversion method. The effect of GO on the synthesized membrane morphology and hydrophilicity was studied by using FE-SEM, AFM, contact angle, zeta potential, porosity and pore size tests. The membrane performance was also evaluated in terms of pure water flux and arsenate rejection.

RESULTS

ATR-FTIR confirmed the presence of hydrophilic functional groups on the surface of the prepared GO. FE-SEM micrographs showed that with increasing GO content in the casting solution, the sub-layer structure was enhanced and the drop like voids in the pure PSF membrane changed to macrovoids in PSF/GO membrane along with increase in porosity. AFM images indicated lower roughness of modified membrane compared to pure PSF membrane. Furthermore, contact angle measurement and permeation experiment showed that by increasing GO up to 1 wt%, membrane hydrophilicity and pure water flux were increased. For PSF/GO-1, pure water flux was calculated about 50 L/m(2)h at 4 bar. The maximum rejection was obtained by PSF/GO-2 about 83.65 % at 4 bar. Moreover, it was revealed that arsenate rejection depended on solution pH values. It was showed that with increasing pH, the rejection increased.

CONCLUSIONS

This study showed that application of GO as an additive to PSF casting solution could enhance the membrane hydrophilicity, porosity, flux and arsenate rejection.