A bioinspired fouling-resistant surface modification for water purification membranes

UV-LED silicon carbide composite photocatalytic membrane reactor for the degradation of organic contaminants

The utilization of membranes in the water industry has been growing rapidly; however, the technology still experiences problems with fouling. A potential solution is to immobilize photocatalyst particles on the surface of the membranes to encourage in situ degradation of the organic contaminants contributing to the fouling. In this study, we developed a photocatalytic membrane (PM) by coating a silicon carbide membrane with Zr/TiO₂ sol. The performance of the PM in degrading different concentrations of humic acid was evaluated comparatively under UV irradiation of two wavelengths, 275 and 365 nm. The results indicated that (i) the PM achieved high levels of humic acid degradation, (ii) the photocatalytic activity of the PM reduced the formation of fouling and hence the loss of permeability, (iii) the formation of fouling was reversible; no trace of fouling was observed after cleaning, and (iv) the PM showed high durability during multiple rounds of operation.

How to achieve air resistance control in hollow fiber membrane process: Membrane vibration or inner surface modification?

As a factor affecting the efficiency of hollow fiber membrane filtration, air resistance is gradually being discovered. To obtain a better air resistance control strategy, in the study, two representative strategies have been proposed, namely, membrane vibration and inner surface modification, which was achieved by aeration combined with looseness-induced membrane vibration and dopamine (PDA) hydrophilic modification of the inner surface, respectively. The performance of two strategies was based on Fiber Bragg Grating (FBG) sensing technology and ultrasonic phased array (UPA) technology to achieve real-time monitoring. Mathematical model result shows that in hollow fiber membrane modules, the initial appearance of air resistance causes a rapid reduction in filtration efficiency, while this effect diminishes as the air resistance increases. Besides, experimental results show that aeration combined with fiber looseness helps to inhibit air aggregation and accelerate air escape, while inner surface modification enhances the hydrophilicity of inner surface, weakens the air adhesion and increases the drag force of fluid on air bubbles. In the corresponding optimized state, both strategies perform well in optimizing the air resistance control, and the improvement in flux enhancement ability for the two strategies is 26.92 and 34.10%, respectively.

Lyotropic Liquid Crystal (LLC)-Templated Nanofiltration Membranes by Precisely Administering LLC/Substrate Interfacial Structure

Mesoporous materials based on lyotropic liquid crystal templates with precisely defined and flexible nanostructures offer an alluring solution to the age-old challenge of water scarcity. In contrast, polyamide (PA)-based thin-film composite (TFC) membranes have long been hailed as the state of the art in desalination. They grapple with a common trade-off between permeability and selectivity. However, the tides are turning as these novel materials, with pore sizes ranging from 0.2 to 5 nm, take center stage as highly coveted active layers in TFC membranes. With the ability to regulate water transport and influence the formation of the active layer, the middle porous substrate of TFC membranes becomes an essential player in unlocking their true potential. This review delves deep into the recent advancements in fabricating active layers using lyotropic liquid crystal templates on porous substrates. It meticulously analyzes the retention of the liquid crystal phase structure, explores the membrane fabrication processes, and evaluates the water filtration performance. Additionally, it presents an exhaustive comparison between the effects of substrates on both polyamide and lyotropic liquid crystal template top layer-based TFC membranes, covering crucial aspects such as surface pore structures, hydrophilicity, and heterogeneity. To push the boundaries even further, the review explores a diverse array of promising strategies for surface modification and interlayer introduction, all aimed at achieving an ideal substrate surface design. Moreover, it delves into the realm of cutting-edge techniques for detecting and unraveling the intricate interfacial structures between the lyotropic liquid crystal and the substrate. This review is a passport to unravel the enigmatic world of lyotropic liquid crystal-templated TFC membranes and their transformative role in global water challenges.

Removal of natural organic matter from surface water sources by nanofiltration and surface engineering membranes for fouling mitigation - A review

Given that surface water is the primary supply of drinking water worldwide, the presence of natural organic matter (NOM) in surface water presents difficulties for water treatment facilities. During the disinfection phase of the drinking water treatment process, NOM aids in the creation of toxic disinfection by-products (DBPs). This problem can be effectively solved using the nanofiltration (NF) membrane method, however NOM can significantly foul NF membranes, degrading separation performance and membrane integrity, necessitating the development of fouling-resistant membranes. This review offers a thorough analysis of the removal of NOM by NF along with insights into the operation, mechanisms, fouling, and its controlling variables. In light of engineering materials with distinctive features, the potential of surface-engineered NF membranes is here critically assessed for the impact on the membrane surface, separation, and antifouling qualities. Case studies on surface-engineered NF membranes are critically evaluated, and properties-to-performance connections are established, as well as challenges, trends, and predictions for the field's future. The effect of alteration on surface properties, interactions with solutes and foulants, and applications in water treatment are all examined in detail. Engineered NF membranes containing zwitterionic polymers have the greatest potential to improve membrane permeance, selectivity, stability, and antifouling performance. To support commercial applications, however, difficulties related to material production, modification techniques, and long-term stability must be solved promptly. Fouling resistant NF membrane development would be critical not only for the water treatment industry, but also for a wide range of developing applications in gas and liquid separations.

Designing sustainable membrane-based water treatment via fouling control through membrane interface engineering and process developments

Membrane-based water treatment processes have been established as a powerful approach for clean water production. However, despite the significant advances made in terms of rejection and flux, provision of sustainable and energy-efficient water production is restricted by the inevitable issue of membrane fouling, known to be the major contributor to the elevated operating costs due to frequent chemical cleaning, increased transmembrane resistance, and deterioration of permeate flux. This review provides an overview of fouling control strategies in different membrane processes, such as microfiltration, ultrafiltration, membrane bioreactors, and desalination via reverse osmosis and forward osmosis. Insights into the recent advancements are discussed and efforts made in terms of membrane development, modules arrangement, process optimization, feed pretreatment, and fouling monitoring are highlighted to evaluate their overall impact in energy- and cost-effective water treatment. Major findings in four key aspects are presented, including membrane surface modification, modules design, process integration, and fouling monitoring. Among the above mentioned anti-fouling strategies, a large part of research has been focused on membrane surface modifications using a number of anti-fouling materials whereas much less research has been devoted to membrane module advancements and in-situ fouling monitoring and control. At the end, a critical analysis is provided for each anti-fouling strategy and a rationale framework is provided for design of efficient membranes and process for water treatment.

Fast preparation of a polydopamine/ceramic composite nanofiltration membrane with excellent permselectivity

Fabrication of a dense polymer/ceramic composite membrane with high permeability remains a great challenge. In this study, a highly selective polydopamine (PDA)/ceramic composite nanofiltration (NF) membrane was prepared by using an Al₂O₃ ceramic membrane with pore size of 0.1 μm as the support layer. In order to improve the membrane formation rate, KMnO₄ was introduced to oxidize the dopamine to improve the reactivity, and Na₂CO₃ was used to adjust the pH value of the dopamine solution. When the addition amount of KMnO₄ is 0.2 g L^-1 and that of Na₂CO₃ is 1 g L^-1, a functional layer can be formed within 10 min. PDA and polyethyleneimine (PEI) were added to the functional layer to adjust the selectivity of the composite membrane. The composite membrane showed a rejection of 99.7% towards Congo red dye with a high flux of 165 L (m² h bar)^-1 at ambient temperature. After 3 h treatment with Congo red, the fouling resistance of the membrane was improved compared with that of the ceramic based membrane. The surface morphology and composition of the composite membrane were also characterized with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), which confirmed the successful preparation of the PDA/ceramic composite membrane.

Surface modification of thin film composite forward osmosis membrane using graphene nanosheets for water desalination

In this study, the main motivation of this work is desalination of water for irrigation arid area such as Sidri- Baba basins- south Sinai, Egypt. Also, the novelty of this work is modification of TFC surface membrane by mix of HA, DA and GO to get high performance of FO technique. Interfacial polymerization was employed to modify a thin-film composite (TFC) membrane for forward osmosis (FO) applications; moreover, graphene oxide (GO) nanosheets (GONs), a dopamine solution (DA), and naturally accessible humic acid (HA) were modified on a polyethersulfone (PES) substrate. The effects of the different quantities of GO, HA, and DA on the membrane surfaces, as well as their various cross-sectional morphologies and FO-desalination capabilities, were investigated. The integrated TFC membrane containing appropriate GO, HA, and DA blends outperformed the control membrane, obtaining high water flux, and high salt rejection. Furthermore,.

Surface Modification of Ultrafiltration Membranes with 1,4-Benzoquinone and Polyetheramines to Improve Fouling Resistance

Membrane fouling remains a key challenge for membrane separations. Hydrophilic membrane surface modification can mitigate irreversible foulant deposition, thereby improving fouling resistance. We report new hydrophilic membrane coatings based on 1,4-benzoquinone and various commercially available polyetheramines. These coatings, prepared from 1,4-benzoquinone and Jeffamine EDR 148, poly(benzoquinone-Jeffamine EDR 148) (p(BQ-EDR 148)), were used to modify polysulfone (PS) ultrafiltration membranes. In fouling experiments using an oil/water emulsion, membranes exhibited comparable fouling resistance to that of polydopamine (pDA)-modified membranes. Based on contact angle measurements, p(BQ-EDR 148) and pDA-modified membranes have similar levels of hydrophilicity, and both exhibited higher threshold flux values than those of their unmodified analogues. Based on their similar threshold flux values, p(BQ-EDR 148)-modified (76 LMH) and pDA-modified membranes (74 LMH) should have similar fouling resistance. Moreover, the mean pore size of p(BQ-EDR 148)-modified membranes can be tuned, while keeping the pure water permeance constant, by changing the deposition time and molar ratio of benzoquinone to EDR 148 in the modification solution.

Tailoring Morphology and Properties of Tight Utrafiltration Membranes by Two-Dimensional Molybdenum Disulfide for Performance Improvement

To enhance the permeation and separation performance of the polyethersulfone (PES) tight ultrafiltration (TUF) membrane, two-dimensional molybdenum disulfide (MoS2) was applied as a modifier in low concentrations. The influence of different concentrations of MoS2 (0, 0.25, 0.50, 1.00, and 1.50 wt%) on TUF membranes was investigated in terms of morphology, mechanical strength properties, permeation, and separation. The results indicate that the blending of MoS2 tailored the microstructure of the membrane and enhanced the mechanical strength property. Moreover, by embedding an appropriate amount of MoS2 into the membrane, the PES/MoS2 membranes showed improvement in permeation and without the sacrifice of the rejection of bovine serum protein (BSA) and humic acid (HA). Compared with the pristine membrane, the modified membrane embedded with 0.5 wt% MoS2 showed a 36.08% increase in the pure water flux, and >99.6% rejections of BSA and HA. This study reveals that two-dimensional MoS2 can be used as an effective additive to improve the performance and properties of TUF membranes for water treatment.

Thin Film Composite Polyamide Reverse Osmosis Membrane Technology towards a Circular Economy

It is estimated that Reverse Osmosis (RO) desalination will produce, by 2025, more than 2,000,000 end-of-life membranes annually worldwide. This review examines the implementation of circular economy principles in RO technology through a comprehensive analysis of the RO membrane life cycle (manufacturing, usage, and end-of-life management). Future RO design should incorporate a biobased composition (biopolymers, recycled materials, and green solvents), improve the durability of the membranes (fouling and chlorine resistance), and facilitate the recyclability of the modules. Moreover, proper membrane maintenance at the usage phase, attained through the implementation of feed pre-treatment, early fouling detection, and membrane cleaning methods can help extend the service time of RO elements. Currently, end-of-life membranes are dumped in landfills, which is contrary to the waste hierarchy. This review analyses up to now developed alternative valorisation routes of end-of-life RO membranes, including reuse, direct and indirect recycling, and energy recovery, placing a special focus on emerging indirect recycling strategies. Lastly, Life Cycle Assessment is presented as a holistic methodology to evaluate the environmental and economic burdens of membrane recycling strategies. According to the European Commission's objectives set through the Green Deal, future perspectives indicate that end-of-life membrane valorisation strategies will keep gaining increasing interest in the upcoming years.

Biofouling-Resistant Ultrafiltration Membranes via Codeposition of Dopamine and Cetyltrimethylammonium Bromide with Retained Size Selectivity and Water Flux

Biofouling is a serious problem in ultrafiltration (UF) membrane applications. Modifying the surface of membranes with low molecular weight, commercially available antibacterial chemistries is an excellent strategy to mitigate biofouling. Herein, we report a new strategy to impart antibacterial and anti-biofouling behavior without changing the support membrane's size selectivity and pure water permeance (PWP). To this end, a strong antibacterial agent, cetyltrimethylammonium bromide (CTAB), was codeposited with dopamine onto commercial polyethersulfone (PES) UF membranes in the presence of nitrogen (N₂) gas backflow. The PWP and pore size of the support membrane did not change with codeposition, confirming the benefit of N₂ backflow in mitigating the solution intrusion phenomenon. X-ray photoelectron spectroscopy (XPS), surface ζ potentials, and contact angle measurements confirmed the successful codeposition of polydopamine (PDA) and CTAB onto the membrane. Among three different CTAB concentrations systematically investigated, the membrane functionalized with CTAB at the critical micelle concentration (CMC) provided the best anti-biofouling activity against Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria and retained its surface ζ potential after being stored in 1 M NaCl (pH = 6.8) for 3 months. Our results demonstrate the potential of using a facile, one-step approach to modify commercial UF membranes without compromising their pore size or flux, while simultaneously endowing antibacterial activity.

Biomimetic on-chip filtration enabled by direct micro-3D printing on membrane

Membrane-on-chip is of growing interest in a wide variety of high-throughput environmental and water research. Advances in membrane technology continuously provide novel materials and multi-functional structures. Yet, the incorporation of membrane into microfluidic devices remains challenging, thus limiting its versatile utilization. Herein, via micro-stereolithography 3D printing, we propose and fabricate a "fish gill" structure-integrated on-chip membrane device, which has the self-sealing attribute at structure-membrane interface without extra assembling. As a demonstration, metallic micromesh and polymeric membrane can also be easily embedded in 3D printed on-chip device to achieve anti-fouling and anti-clogging functionality for wastewater filtration. As evidenced from in-situ visualization of structure-fluid-foulant interactions during filtration process, the proposed approach successfully adopts the fish feeding mechanism, being able to "ricochet" foulant particles or droplets through hydrodynamic manipulation. When benchmarked with two common wastewater treatment scenarios, such as plastic micro-particles and emulsified oil droplets, our biomimetic filtration devices exhibit 2 ~ 3 times longer durability for high-flux filtration than devices with commercial membrane. This proposed 3D printing-on-membrane approach, elegantly bridging the fields of microfluidics and membrane science, is instrumental to many other applications in energy, sensing, analytical chemistry and biomedical engineering.

Insights into the impact of polydopamine modification on permeability and anti-fouling performance of forward osmosis membrane

Forward osmosis (FO) has drawn wide attention as a promising method to address world-wide water crisis due to the advantages of low-energy consumption and easy separation operation. Unfortunately, the trade-off between permeability and selectivity as well as membrane fouling hindered the application of forward osmosis. Surface modification is a feasible method to address these issues. However, there is a lack of systematic evaluation about the effect of modification position on FO performance due to the asymmetric structure of thin film composite (TFC) FO membrane. To provide new insights into the design of FO membrane with satisfied permeability and fouling resistance, novel TFC FO membranes were fabricated by introducing polydopamine (PDA) on the support layer (TFC-I) or active layer (TFC-S), respectively. The surface morphology, chemical composition and wettability of the fabricated membrane were studied. It was found that the surface wettability of the modified membrane was improved greatly compared to pristine TFC membrane (TFC-C). Moreover, TFC-S membrane displayed a rougher surface than that of TFC-I membrane. As a result, a superior TFC-S membrane with a water flux of 60.95 ± 3.15 L m^-2h^-1 in AL-DS mode was obtained, which was 72.61% and 17.87% higher than that of TFC-C and TFC-I membrane, respectively. In addition, the TFC-S membrane also presented an excellent fouling resistance and membrane regeneration performance during the three organic fouling cycle experiments. The results indicated that the introduction of PDA as a surface coating for TFC membranes modification guaranteed the high-performance and fouling resistance. Especially, the PDA coating on the support layer surface resulted in an enhancement in permeability, while both the permeability and anti-fouling performance were significantly improved with the PDA coating on the polyamide active layer surface. This study provides new insights into the development of modification TFC-FO membranes for practical applications in water treatment.

Polymeric Membranes for Oil-Water Separation: A Review

This review is devoted to the application of bulk synthetic polymers such as polysulfone (PSf), polyethersulfone (PES), polyacrylonitrile (PAN), and polyvinylidene fluoride (PVDF) for the separation of oil-water emulsions. Due to the high hydrophobicity of the presented polymers and their tendency to be contaminated with water-oil emulsions, methods for the hydrophilization of membranes based on them were analyzed: the mixing of polymers, the introduction of inorganic additives, and surface modification. In addition, membranes based on natural hydrophilic materials (cellulose and its derivatives) are given as a comparison.

Biomolecule-Enabled Liquid Separation Membranes: Potential and Recent Progress

The implementation of membrane surface modification to enhance the performance of membrane-based separation has become a favored strategy due to its promise to address the trade-off between water permeability and salt rejection as well as to improve the durability of the membranes. Tremendous work has been committed to modifying polymeric membranes through physical approaches such as surface coating and ontology doping, as well as chemical approaches such as surface grafting to introduce various functional groups to the membrane. In the context of liquid separation membranes applied for desalination and water and wastewater treatment, biomolecules have gained increasing attention as membrane-modifying agents due to their intriguing structural properties and chemical functionalities. Biomolecules, especially carbohydrates and proteins, exhibit attractive features, including high surface hydrophilicity and zwitterionic and antimicrobial properties that are desired for liquid separation membranes. In this review, we provide an overview of the recent developments in biomolecule-enabled liquid separation membranes. The roles and potentials of some commonly explored biomolecules in heightening the performance of polymeric membranes are discussed. With the advancements in material synthesis and the need to answer the call for more sustainable materials, biomolecules could serve as attractive alternatives for the development of high-performance composite membranes.

Effects of mussel-inspired co-deposition of 2-hydroxymethyl methacrylate and poly (2-methoxyethyl acrylate) on the hydrophilicity and binding tendency of common hemodialysis membranes: Molecular dynamics simulations and molecular docking studies

Despite advances in the field, hemoincompatibility remains a critical issue for hemodialysis (HD) as interactions between various human blood constituents and the polymeric structure of HD membranes results in complications such as activation of immune system cascades. Adding hydrophilic polymer structures to the membranes is one modification approach that can decrease the extent of protein adsorption. This study conducted molecular dynamics (MD) simulations to understand the interactions between three human serum proteins (fibrinogen [FB], human serum albumin, and transferrin) and common HD membranes in untreated and modified forms. Poly(aryl ether sulfone) (PAES) and cellulose triacetate were used as the common dialyzer polymers, and membrane modifications were performed with 2-hydroxymethyl methacrylate (HEMA) and poly (2-methoxyethyl acrylate) (PMEA), using polydopamine-assisted co-deposition. The MD simulations were used as the framework for binding energy simulations, and molecular docking simulations were also performed to conduct molecular-level investigations between the two modifying polymers (HEMA and PMEA) and FB. Each of the three proteins acted differently with the membranes due to their unique nature and surface chemistry. The simulations show PMEA binds less intensively to FB with a higher number of hydrogen bonds, which reflects PMEA's superior performance compared to HEMA. The simulations suggest PAES membranes could be used in modified forms for blood-contact applications as they reflect the lowest binding energy to blood proteins.

Ultrasound-assisted dopamine polymerization: rapid and oxidizing agent-free polydopamine coatings on membrane surfaces

Herein, we report a controllable pathway to accelerate the polymerization kinetics of dopamine using ultrasound as a trigger. The use of ultrasound was demonstrated to dramatically accelerate the slow liquid phase reaction kinetics and increase the deposition rate of the polydopamine coating on the surface of polymeric membranes.

Surface modification of nanofiltration membranes to improve the removal of organic micropollutants: Linking membrane characteristics to solute transmission

Surface modification of nanofiltration (NF) membranes has great potential to improve the removal of organic micropollutants (OMs) by NF membranes. This study used polydopamine (PDA) as a model coating to comprehensively link the changes in membrane properties with the changes in transmission of 34 OMs. The membrane characterization demonstrated that a thicker, denser, and more hydrophilic PDA coating can be achieved by increasing the PDA deposition time from 0.5 to 4 hours. Overall, the transmissions of target OMs were reduced by PDA-coated NF membranes compared to unmodified NF membranes. The neutral hydrophobic compounds showed lower transmissions for longer PDA coating (PDA4), while the neutral hydrophilic compounds tended to show lower transmissions for shorter PDA coating (PDA0.5). To explain this, competing effects provided by the PDA coatings are proposed including sealing defects, inducing cake-enhanced concentration polarization in the coating layer for neutral hydrophilic compounds, and weakened hydrophobic adsorption for neutral hydrophobic compounds. For charged compounds, PDA4 with the greatest negative charge among the PDA-coated membranes showed the lowest transmission. Depending on the molecular size and hydrophilicity of the compounds, the transmission of OMs by the PDA4 coating could be reduced by 70% with only a 26.4% decline in water permeance. The correlations and mechanistic insights provided by this work are highly useful for designing membranes with specific surface properties via surface modification to improve the removal of OMs without compromising water production.

The translocation dynamics of the polymer through a conical pore: Non-stuck, weak-stuck, and strong-stuck modes

The external voltage-driven polymer translocation through a conical pore (with a large opening at the entry and a small tip at the exit) is studied by using the Langevin dynamics simulation in this paper. The entire translocation process is divided into an approaching stage and a threading stage. First, the approaching stage starts from the polymer entering the large opening and ends up at a terminal monomer reaching the pore tip. In this stage, the polymer will undergo the conformation adjustment to fit the narrowed cross-sectional area of the pore, leading to three approaching modes: the non-stuck mode with a terminal monomer arriving at the pore tip smoothly, the weak-stuck mode for the polymer stuck inside the pore for a short duration with minor conformational adjustments, and the strong-stuck mode with major conformational changes and a long duration. The approaching times (the duration of the approaching stage) of the three approaching modes show different behavior as a function of the pore apex angle. Second, the threading stage describes that the polymer threads through the pore tip with a linear fashion. In this stage, an increase in the apex angle causes the reduction of the threading time (the duration of the threading stage) due to the increase in the driving force with the apex angle at the tip. Moreover, we also find that with the increase in the apex angle or the polymer length, the polymer threading dynamics will change from the quasi-equilibrium state to the non-equilibrium state.

Polydopamine Ultrathin Film Growth on Mica via In-Situ Polymerization of Dopamine with Applications for Silver-Based Antimicrobial Coatings

The development of polydopamine (PDA) coatings with a nanometer-scale thickness on surfaces is highly desirable for exploiting the novel features arising from the specific structure on the molecular level. Exploring the mechanisms of thin-film growth is helpful for attaining desirable control over the useful properties of materials. We present a systematic study demonstrating the growth of a PDA thin film on the surface of mica in consecutive short deposition time intervals. Film growth at each deposition time was monitored through instrumental techniques such as atomic force microscopy (AFM), water contact angle (WCA) analysis, and X-ray photoelectron spectroscopy (XPS). Film growth was initiated by adsorption of the PDA molecules on mica, with subsequent island-like aggregation, and finally, a complete molecular level PDA film was formed on the surface due to further molecular adsorption. A duration of 60−300 s was sufficient for complete formation of the PDA layer within the thickness range of 0.5−1.1 nm. An outstanding feature of PDA ultrathin films is their ability to act as a molecular adhesive, providing a foundation for constructing functional surfaces. We also explored antimicrobial applications by incorporating Ag nanoparticles into a PDA film. The Ag NPs/PDA film was formed on a surgical blade and then characterized and confirmed by SEM-EDS and XPS. The modified film inhibited bacterial growth by up to 42% on the blade after cutting through a pork meat sample.

Anaerobic wastewater treatment and reuse enabled by thermophilic bioprocessing integrated with a bioelectrochemical/ultrafiltration module

The current study aimed to develop an anaerobic wastewater treatment and reuse module enabled by thermophilic bioprocessing, a microbial fuel cell (MFC) and ultrafiltration (UF) treatment. A previously unexplored consortium based on Thermoanaerobacterium thermosaccharolyticum and Arcobacter sp. was used to remove ~73% of chemical oxygen demand (COD) from wastewater under anaerobic conditions (COD_i = 200 mg/L). The subsequent MFC and UF treatment removed the COD remnants to meet the secondary treatment standards and reuse criteria. The energy efficiency of polyethersulfone UF membranes was improved by modifying their surfaces with coatings based on self-polymerized dopamine, mixtures of dopamine and poly(2-dimethylamino) ethyl methacrylate methyl, and dopamine analog norepinephrine. The resulting hydrophilic, anti-fouling layers were found to reduce interactions between rejected species and the membrane surface. Finally, this study presents a comparative treatment performance and energy efficiency of the wastewater treatment and reuse modules arranged in six different configurations.

Antibacterial behaviour of surface modified composite polyamide nanofiltration (NF) membrane by immobilizing Ag-doped TiO2 nanoparticles

Modification of active membrane surface is an auspicious way to enhance the membrane performance. In our study, a commercially available composite polyamide Nanofiltration (NF) membrane was modified by immobilizing silver doped TiO₂ (Ag-TiO₂) nanoparticles. Ag-TiO₂ with different nanoparticles concentration (0.05, 0.1, and 0.5 wt. %) were coated on the surface of the membrane by a dip coating method. The evidence of successful coating was evaluated by Scanning Electron Microscopy coupled with Energy Dispersive Spectroscopy and Atomic Force Microscopy images. Moreover, the Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), contact angle measurement and permeation tests were carried out in order to evaluate the membrane performance after coating. The antifouling property of the modified membrane was evaluated for Gram-positive (Bacillus subtilis) and Gram-negative (Escherichia coli) bacteria by colony counting method. The results indicated that the modified membranes keep efficient antibacterial efficacy against both types of bacteria. The bacterial growth reduced approximately 93% and 91% on the modified membrane as compared to the unmodified membrane for E.coli and B.subtilis, respectively. Ag-TiO₂ nanoparticles imbedded nanofiltration membranes inhibit the biofilm formation and facilitate in cleaning membrane surface without using excessive chemical agents.

Grafting Activated Graphene Oxide Nanosheets onto Ultrafiltration Membranes Using Polydopamine to Enhance Antifouling Properties

Graphene oxide (GO) nanosheets are negatively charged and exhibit excellent antifouling properties. However, their hydrophilicity makes it challenging for their grafting onto membrane surfaces to improve antifouling properties for long-term underwater operation. Herein, we demonstrate a versatile approach to covalently graft GO onto ultrafiltration membrane surfaces in aqueous solutions at ≈22 °C. The membrane surface is first primed using dopamine and then reacted with activated GO (aGO) containing amine-reactive esters. The aGO grafting improves the membrane surface hydrophilicity without decreasing water permeance. When the membranes are challenged with 1.0 g/L sodium alginate in a constant-flux crossflow system, the aGO grafting increases the critical flux by 20% and reduces the fouling rate by 63% compared with the pristine membrane. The modified membranes demonstrate stability for 48 h operation and interval cleanings using NaOH solutions.

Antifouling Property of Oppositely Charged Titania Nanosheet Assembled on Thin Film Composite Reverse Osmosis Membrane for Highly Concentrated Oily Saline Water Treatment

With the blooming of oil and gas industries, oily saline wastewater treatment becomes a viable option to resolve the oily water disposal issue and to provide a source of water for beneficial use. Reverse osmosis (RO) has been touted as a promising technology for oily saline wastewater treatment. However, one great challenge of RO membrane is fouling phenomena, which is caused by the presence of hydrocarbon contents in the oily saline wastewater. This study focuses on the fabrication of antifouling RO membrane for accomplishing simultaneous separation of salt and oil. Thin film nanocomposite (TFN) RO membrane was formed by the layer by layer (LbL) assembly of positively charged TNS (pTNS) and negatively charged TNS (nTNS) on the surface of thin film composite (TFC) membrane. The unique features, rendered by hydrophilic TNS bilayer assembled on TFC membrane in the formation of a hydration layer to enhance the fouling resistance by high concentration oily saline water while maintaining the salt rejection, were discussed in this study. The characterization findings revealed that the surface properties of membrane were improved in terms of surface hydrophilicity, surface roughness, and polyamide(PA) cross-linking. The TFC RO membrane coated with 2-bilayer of TNS achieved >99% and >98% for oil and salt rejection, respectively. During the long-term study, the 2TNS-PA TFN membrane outperformed the pristine TFC membrane by exhibiting high permeability and much lower fouling propensity for low to high concentration of oily saline water concentration (1000 ppm, 5000 ppm and 10,000 ppm) over a 960 min operation. Meanwhile, the average permeability of uncoated TFC membrane could only be recovered by 95.7%, 89.1% and 82.9% for 1000 ppm, 5000 ppm and 10,000 ppm of the oily saline feedwater, respectively. The 2TNS-PA TFN membrane achieved almost 100% flux recovery for three cycles by hydraulic washing.

Grafting polysiloxane onto ultrafiltration membranes to optimize surface energy and mitigate fouling

Conventional approaches to mitigate fouling of membrane surfaces impart hydrophilicity to the membrane surface, which increases the water of hydration and fluidity near the surface. By contrast, we demonstrate here that tuning the membrane surface energy close to that of the dispersive component of water surface tension (21.8 mN m^-1) can also improve the antifouling properties of the membrane. Specifically, ultrafiltration (UF) membranes were first modified using polydopamine (PDA) followed by grafting of amine-terminated polysiloxane (PSi-NH₂). For example, with 2 g L^-1 PSi-NH₂ coating solution, the obtained coating layer contains 53% by mass fraction PSi-NH₂ and exhibits a total surface energy of 21 mN m^-1, decreasing the adsorption of bovine serum albumin by 44% compared to the unmodified membrane. When challenged with 1 g L^-1 sodium alginate in a constant-flux crossflow system, the PSi-NH₂-grafted membrane exhibits a 70% lower fouling rate than the pristine membrane at a water flux of 110 L (m² h)^-1 and good stability when cleaned with NaOH solutions.