Quantitative evaluation of fouling resistance of PVDF/PMMA-g-PEO polymer blend membranes for membrane bioreactor

Unveiling the spatiotemporal dynamics of membrane fouling: A focused review on dynamic fouling characterization techniques and future perspectives

Membrane technology has emerged as a crucial method for obtaining clean water from unconventional sources in the face of water scarcity. It finds wide applications in wastewater treatment, advanced treatment, and desalination of seawater and brackish water. However, membrane fouling poses a huge challenge that limits the development of membrane-based water treatment technologies. Characterizing the dynamics of membrane fouling is crucial for understanding its development, mechanisms, and effective mitigation. Instrumental techniques that enable in situ or real-time characterization of the dynamics of membrane fouling provide insights into the temporal and spatial evolution of fouling, which play a crucial role in understanding the fouling mechanism and the formulation of membrane control strategies. This review consolidates existing knowledge about the principal advanced instrumental analysis technologies employed to characterize the dynamics of membrane fouling, in terms of membrane structure, morphology, and intermolecular forces. Working principles, applications, and limitations of each technique are discussed, enabling researchers to select appropriate methods for their specific studies. Furthermore, prospects for the future development of dynamic characterization techniques for membrane fouling are discussed, underscoring the need for continued research and innovation in this field to overcome the challenges posed by membrane fouling.

Hemocompatibility challenge of membrane oxygenator for artificial lung technology

The artificial lung (AL) technology is one of the membrane-based artificial organs that partly augments lung functions, i.e. blood oxygenation and CO₂ removal. It is generally employed as an extracorporeal membrane oxygenation (ECMO) device to treat acute and chronic lung-failure patients, and the recent outbreak of the COVID-19 pandemic has re-emphasized the importance of this technology. The principal component in AL is the polymeric membrane oxygenator that facilitates the O₂/CO₂ exchange with the blood. Despite the considerable improvement in anti-thrombogenic biomaterials in other applications (e.g., stents), AL research has not advanced at the same rate. This is partly because AL research requires interdisciplinary knowledge in biomaterials and membrane technology. Some of the promising biomaterials with reasonable hemocompatibility - such as emerging fluoropolymers of extremely low surface energy - must first be fabricated into membranes to exhibit effective gas exchange performance. As AL membranes must also demonstrate high hemocompatibility in tandem, it is essential to test the membranes using in-vitro hemocompatibility experiments before in-vivo test. Hence, it is vital to have a reliable in-vitro experimental protocol that can be reasonably correlated with the in-vivo results. However, current in-vitro AL studies are unsystematic to allow a consistent comparison with in-vivo results. More specifically, current literature on AL biomaterial in-vitro hemocompatibility data are not quantitatively comparable due to the use of unstandardized and unreliable protocols. Such a wide gap has been the main bottleneck in the improvement of AL research, preventing promising biomaterials from reaching clinical trials. This review summarizes the current state-of-the-art and status of AL technology from membrane researcher perspectives. Particularly, most of the reported in-vitro experiments to assess AL membrane hemocompatibility are compiled and critically compared to suggest the most reliable method suitable for AL biomaterial research. Also, a brief review of current approaches to improve AL hemocompatibility is summarized. STATEMENT OF SIGNIFICANCE: The importance of Artificial Lung (AL) technology has been re-emphasized in the time of the COVID-19 pandemic. The utmost bottleneck in the current AL technology is the poor hemocompatibility of the polymer membrane used for O₂/CO₂ gas exchange, limiting its use in the long-term. Unfortunately, most of the in-vitro AL experiments are unsystematic, irreproducible, and unreliable. There are no standardized in-vitro hemocompatibility characterization protocols for quantitative comparison between AL biomaterials. In this review, we tackled this bottleneck by compiling the scattered in-vitro data and suggesting the most suitable experimental protocol to obtain reliable and comparable hemocompatibility results. To the best of our knowledge, this is the first review paper focusing on the hemocompatibility challenge of AL technology.

Impact of polysaccharide and protein interactions on membrane fouling: Particle deposition and layer formation

Membrane fouling, which limits the application of membrane bioreactors, has received considerable research attention in recent years. In this work, filtration modeling was performed in combination with surface plasmon resonance (SPR) analysis to investigate the membrane fouling mechanism. Sodium alginate (SA) and bovine serum albumin (BSA) were used to perform dead-end filtration on hydrophilic and hydrophobic poly (vinylidene fluoride) (PVDF) membranes. The initial foulant deposition and layer formation on membranes as well as the interaction between the BSA and SA were comprehensively analyzed. Results indicated that during SA filtration, initial fouling on hydrophilic membranes were primarily attributed to the particle-membrane interactions, while the fouling on the hydrophobic membrane were dominantly caused by the interactions among SA particles. The interaction between BSA and SA led to more severe membrane fouling and hydrophobic membrane was more sensitive to it, especially in the initial filtration process. The SPR results helped clarify the in-situ deposition behavior of BSA and SA particles on the PVDF surface. Compared to SA, BSA adsorbed faster on the PVDF membrane, and specific interactions played an essential role in BSA adsorption, whereas the deposition of SA on PVDF could be easily removed by shear force. Interactions between BSA and SA could alleviate the bonding between BSA and the PVDF membrane.

Upgrading of bio-separation and bioanalysis using synthetic polymers: Molecularly imprinted polymers (MIPs), cryogels, stimuli-responsive polymers

Bio-separation plays a crucial role in many areas. Different polymers are suitable for bio-separation and are useful for applications in applications in both science and technology. Besides biopolymers, there are a broad spectrum of synthetic polymers with tailor-made properties. The synthetic polymers are characterized by their charges, solubility, hydrophilicity/hydrophobicity, sensitivity to environmental conditions and stability. Furthermore, ongoing developments are of great interest on biodegradable polymers for the treatment of diseases. Smart polymers have gained great attention due to their unique characteristics especially emphasizing simultaneously changing their chemical and physical property upon exposure to changes in environmental conditions. In this review, methodologies applied in bio-separation using synthetic polymers are discussed and efficient candidates are focused for the construction of synthetic polymers.

Fabricating novel PVDF-g-IBMA copolymer hydrophilic ultrafiltration membrane for treating papermaking wastewater with good antifouling property

Ultrafiltration membranes are widely used for the treatment of papermaking wastewater. The antifouling performance of polyvinylidene fluoride (PVDF) ultrafiltration membranes can be improved by changing the hydrophilicity. Here, a novel amphiphilic copolymer material, PVDF grafted with N-isobutoxy methacrylamide (PVDF-g-IBMA), was prepared using ultraviolet-induced Cu(II)-mediated reversible deactivation radical polymerization. The amphipathic copolymer was used to prepare ultrafiltration membrane via NIPS. The prepared PVDF-g-IBMA ultrafiltration membrane was estimated using ¹H NMR, FT-IR, and DSC. The contact angle, casting viscosity, and the permeation performance of the PVDF-g-IBMA ultrafiltration membrane were also determined. The pure water flux, bovine serum albumin removal rate, and pure water flux recovery rate of the PVDF-g-IBMA ultrafiltration membrane were 432.8 L·m^-2·h^-1, 88.4%, and 90.8%, respectively. Furthermore, for the treatment of actual papermaking wastewater, the chemical oxygen demand and turbidity removal rates of the membrane were 61.5% and 92.8%, respectively. The PVDF-g-IBMA amphiphilic copolymer ultrafiltration membrane exhibited good hydrophilicity and antifouling properties, indicating its potential for treating papermaking wastewater.

A brief review of anaerobic membrane bioreactors emphasizing recent advancements, fouling issues and future perspectives

This review summarizes the recent development and studies of anaerobic membrane bioreactor (AnMBR) to control fouling issues. AnMBR is an emerging waste water treatment technology mainly because of its low sludge residual, high volumetric organic removal rate, complete liquid-solid separation, better effluent quality, efficient resource recovery and the small footprint. This paper surveys the fundamental aspects of AnMBRs, including its applications, membrane configurations, and recent progress for enhanced reactor performance. Furthermore, the membrane fouling, a major restriction in the practical application of AnMBR, its mechanism and antifouling strategies like membrane cleaning, quorum quenching, ultrasonic treatment, membrane modifications, and antifouling agents are briefly discussed. Based on the review, the key issues that require urgent attention to facilitate large scale and integrated application of AnMBR technology are identified and future research perspectives relating to the prevalent issues are proposed.

Advancements in SPR biosensing technology: An overview of recent trends in smart layers design, multiplexing concepts, continuous monitoring and in vivo sensing

Inspired by the rapid progress and existing limitations in surface plasmon resonance (SPR) biosensing technology, we have summarized the recent trends in the fields of both chip-SPR and fiber optic (FO)-SPR biosensors during the past five years, primarily regarding smart layers design, multiplexing, continuous monitoring and in vivo sensing. Versatile surface chemistries, biomaterials and nanomaterials have been utilized thus far to generate smart layers on SPR platforms and as such achieve oriented immobilization of bioreceptors, improved fouling resistance and sensitivity enhancement, collectively aiming to improve the biosensing performance. Furthermore, often driven by the desires for time- and cost-effective quantification of multiple targets in a single measurement, efforts have been made to implement multiplex bioassays on SPR platforms. While this aspect largely remains difficult to attain, numerous alternative strategies arose for obtaining parallel analysis of multiple analytes in one single device. Additionally, one of the upcoming challenges in this field will be to succeed in using SPR platforms for continuous measurements and in vivo sensing, and as such match up other biosensing platforms where these goals have been already conquered. Overall, this review will give insight into multiple possibilities that have become available over the years for boosting the performance of SPR biosensors. However, because combining them all into one optimal sensor is practically not feasible, the final application needs to be considered while designing an SPR biosensor, as this will determine the requirements of the bioassay and will thus help in selecting the essential elements from the recent progress made in SPR sensing.

A Brief Review on the Resistance-in-Series Model in Membrane Bioreactors (MBRs)

The cake layer deposited on the membrane modules of membrane bioreactors (MBRs), especially under a submerged configuration, represents a relevant and fundamental mechanism deeply influencing the development of membrane fouling. It negatively affects the total resistance to filtration, while exerting a positive effect as a "pre-filter" promoting the "dynamic membrane" that protects the physical membrane from internal fouling. These two opposite phenomena should be properly managed, where the submerged membranes are usually subjected to a periodical cake layer removal through ordinary (permeate backwashing and air scouring) and/or irregular cleaning actions (manual physical cleaning). In this context, the physical removal of the cake layer is needed to maintain the design filtration characteristics. Nevertheless, the proper evaluation of the effect of physical cleaning operations is still contradictory and under discussion, referring in particular to the correct evaluation of fouling mechanisms. The aim of the present work was to summarize the different aspects that influence the fouling investigations, based on simple models for the evaluation of the resistance to filtration due to the cake layer, through physical cleaning operations.

Preparation and characterization of anti-fouling PVDF membrane modified by chitin

Poly(vinylidene fluoride) (PVDF)/chitin (CH) blend membranes were prepared via the method of immersion-precipitation phase transformation with the solvent system N,N-dimethylacetamide (DMAc)/lithium chloride (LiCl) as solvent and water as coagulant. The effect of CH on membrane structure and performance was investigated. Owing to the strong hydrophilicity, CH chains enriched on the blend membrane surface and improved the hydrophilicity of the membrane. The addition of CH also led to the formation of finger-like pores and the increase of pore size and porosity. The flux and the flux recovery ratio (FRR) of the blend membrane were higher than that of pure PVDF membrane. The fouling resistance of the blend membrane was lower than that of PVDF original membrane. In a word, the addition of CH to PVDF membrane improved the hydrophilicity and the anti-fouling ability of PVDF membrane.

Multifunctionalization of Poly(vinylidene fluoride)/Reactive Copolymer Blend Membranes for Broad Spectrum Applications

Simultaneous immobilization and cross-linking of antifouling/low toxic polymers, e.g., poly(ethylenimine) (PEI), dextran (Dex), agarose (Agr), poly(ethylene glycol) (PEG), PEI-Dex, and PEI-PEG conjugates, and stimuli-responsive copolymers on a porous membrane surface in mild reaction conditions is desirable for the enhancement of hydrophilicity, antifouling character, cytocompatibility, and inducing stimuli-responsive behavior. Grafting to technique is required since the precursors of most of these macromolecules are not amenable to surface-initiated polymerization. In this work, we report a versatile process for the simultaneous immobilization and cross-linking of a library of macromolecules on and into the blend membrane (PVDF-blend) of poly(vinylidene fluoride) and poly(methyl methacrylate)-co-poly(chloromethylstyrene). Sequential nucleophilic substitution reaction between activated halide moieties of the copolymer and amine groups of different macromolecules readily provided series of modified membranes. These membranes exhibited antifouling property superior to that of the unmodified membrane. The effectiveness of this technique has been demonstrated by the immobilization of pH or both pH- and temperature-responsive copolymer on PVDF-blend membrane for responsive separation of poly(ethylene oxide) and bovine serum albumin. Silver nanoparticles were also anchored on the select modified membranes surfaces for the enhancement of antibiofouling property. Our approach is useful to obtain verities of functional membranes and selection of membrane for a particular application.

Enhanced separation and antifouling properties of PVDF ultrafiltration membranes with surface covalent self-assembly of polyethylene glycol

A branched PEG layer on a PVDF membrane surface exhibited exclusion capability to pollutants.