Properties of polyvinyl chloride (PVC) ultrafiltration membrane improved by lignin: Hydrophilicity and antifouling

Biomass-Derived Cellulose Acetate Membranes Modified with TiO2/Graphene Oxide for Oil-In-Water Emulsion Treatment

Considering the environmental impact and health risks caused by oily wastewater in the petrochemical industry, it is crucial to develop more efficient separation techniques than traditional methods, such as membrane separation, for treating stable emulsions enriched with natural surfactants. This study investigated the preparation of dense cellulose acetate membranes from a low-cost biomass precursor (Luffa cylindrica) and their modification with graphene oxide (GO) and TiO2 nanoparticles, aiming to obtain a polymeric nanocomposite with good flux characteristics and selectivity for the treatment of oil/water emulsions. The materials obtained were characterized using techniques such as X-ray diffraction, nuclear magnetic resonance spectroscopy, infrared absorption spectroscopy, along with optical and scanning electron microscopy, among others. The membranes were prepared by the casting technique and modified with the above-mentioned nanostructured materials. Flux analyses with petroleum emulsion revealed that membranes modified with GO and TiO2 nanoparticles showed significant improvements in antifouling resistance compared to unmodified membranes. These enhanced properties highlight the potential of modified cellulose acetate membranes for application in industrial wastewater treatment.

Micro/nanoengineered agricultural by-products for biomedical and environmental applications

Agriculturally derived by-products generated during the growth cycles of living organisms as secondary products have attracted increasing interest due to their wide range of biomedical and environmental applications. These by-products are considered promising candidates because of their unique characteristics including chemical stability, profound biocompatibility and offering a green approach by producing the least impact on the environment. Recently, micro/nanoengineering based techniques play a significant role in upgrading their utility, by controlling their structural integrity and promoting their functions at a micro and nano scale. Specifically, they can be used for biomedical applications such as tissue regeneration, drug delivery, disease diagnosis, as well as environmental applications such as filtration, bioenergy production, and the detection of environmental pollutants. This review highlights the diverse role of micro/nano-engineering techniques when applied on agricultural by-products with intriguing properties and upscaling their wide range of applications across the biomedical and environmental fields. Finally, we outline the future prospects and remarkable potential that these agricultural by-products hold in establishing a new era in the realms of biomedical science and environmental research.

Hydroxyapatite-lignin hybrid systems as improved poly(vinyl chloride) fillers: From preparation to application

In this study, new, functional hydroxyapatite-lignin hybrid systems were designed and characterized. The efficacy of the mechanical method utilized to obtain these systems was confirmed by Fourier transform infrared spectroscopy. The hybrid materials were also noted for their good electrokinetic stability and thermal stability. The introduction of 2.5 to 10 wt% hydroxyapatite-lignin systems into an unplasticized PVC blend using a two-step kneading and pressing method resulted in composites with relatively homogeneous distribution, as confirmed by SEM observations. The processing properties of the filler-containing blends were investigated using plastographometric analysis and MFR tests. The introduction of a lignin-predominant hybrid system into the PVC matrix results in a significant improvement of thermal stability, softening temperature, and tensile strength, while maintaining sufficient impact strength for numerous applications. Hybrid materials containing higher amounts of added lignin are promising materials with bacteriostatic properties. This can be utilized to stabilize and prevent the deposition of microorganisms, as well as the formation of biofilms, on material surfaces, thereby limiting the spread of pathogens. New eco-composites based on PVC and a hybrid filler containing lignin show promise in producing components with surfaces resistant to bacterial colonization. Hence, these materials could be used in medical and hospital equipment.

Preparation and properties of lignin-based composite membranes

Composite membranes were prepared from lignin alkali (LA), polyvinyl alcohol (PVA), and cellulose nanofibrils (CNF) using a simple, low-cost, and environmentally friendly method. The deodorization performances and structures of these membranes were also characterized. The sample referred to as L3C3P5 prepared with a solution containing 35.7 wt% LA, 53.6 wt% PVA, and 10.7 wt% CNF showed the best deodorization properties, and the H2S adsorption time reached 36 min. The adsorption performance was further improved by adding nano-CuO to the membrane, and the H2S adsorption time of the doped membrane L3C3P5C4 reached 60 min. While the H2S adsorption performance improved, structural analysis revealed that the addition of nano-CuO reduced the crystallinity in the membrane, caused the membrane to crack, and led to a decrease in the mechanical properties. The surface oxygens in the L3C3P5C4 membrane were primarily C-O bonds and lattice oxygens in CuO. After the H2S adsorption reaction, the lattice oxygen disappeared, and CuS products appeared.

Porous lignin-based composites for oil/water separation: A review

Frequent oceanic oil spill incidents and the discharge of industrial oily wastewaters have caused serious threats to environments, food chains and human beings. Lignin wastes with many reactive groups exist as the byproducts from bioethanol and pulping processing industries, and they are either discarded as wastes or directly consumed as a fuel. To make full use of lignin wastes and simultaneously deal with oily wastewaters, porous lignin-based composites have been rationally designed and prepared. In this review, recent advances in the preparation of porous lignin-based composites are summarized in terms of aerogels, sponges, foams, papers, and membranes, respectively. Then, the mechanisms and the application of porous lignin-based adsorbents and filtration materials for oil/water separation are discussed. Finally, the challenges and perspectives of porous lignin-based composites are proposed in the field of oil/water separation. The utilization of abundant lignin wastes can replace fossil resources, and meanwhile porous lignin-based composites can be used to efficiently treat with oily wastewaters. The above utilization strategy opens an avenue to the rational design and preparation of lignin wastes with high-added value, and gives a possible solution to use lignin wastes in a sustainable and environmentally friendly way.

Lignin Modification for Enhanced Performance of Polymer Composites

The biopolymer lignin, which is heterogeneous and abundant, is usually present in plant cell walls and gives them rigidity and strength. As a byproduct of the wood, paper, and pulp manufacturing industry, lignin ranks as the second most prevalent biopolymer worldwide, following cellulose. This review paper explores the extraction, modification, and prospective applications of lignin in various industries, including the enhancement of thermosetting and thermoplastic polymers, biomedical applications such as vanillin production, fuel development, carbon fiber composites, and the creation of nanomaterials for food packaging and drug delivery. The structural characteristics of lignin remain undefined due to its origin, separation, and fragmentation processes. This comprehensive overview encompasses state-of-the-art techniques, potential applications, diverse extraction methods, chemical modifications, carbon fiber utilization, and the extraction of vanillin. Moreover, the review focuses on the utilization of lignin-modified polymer blends across multiple manufacturing sectors, providing insights into the advantages and limitations of this innovative approach for the development of environmentally friendly materials.

Water-Triggered Segment Orientation of Long-Lasting Anti-Biofouling Polyurethane Coatings on Biomedical Catheters via Solvent Exchange Strategy

The formation of biofilm and thrombus on medical catheters poses a significant life-threatening concern. Hydrophilic anti-biofouling coatings upon catheter surfaces with complex shapes and narrow lumens are demonstrated to have the potential in reducing complications. However, their effectiveness is constrained by poor mechanical stability and weak substrate adhesion. Herein, a novel zwitterionic polyurethane (SUPU) with strong mechanical stability and long-term anti-biofouling is developed by controlling the ratio of sulfobetaine-diol and ureido-pyrimidinone. Once immersed in water, as-synthesized zwitterionic coating (SUPU3 SE) would undergo a water-driven segment reorientation to obtain much higher durability than its direct drying one, even under various extreme treatments, including acidic solution, abrasion, ultrasonication, flushing, and shearing, in PBS at 37 °C for 14 days. Moreover, SUPU3 SE coating could achieve a 97.1% of exceptional reducing protein fouling, complete prevention of cell adhesion, and long-lasting anti-biofilm performance even after 30 days. Finally, the good anti-thrombogenic formations of SUPU3 SE coating with bacterial treatment are validated in blood circulation through an ex vivo rabbit arteriovenous shunt model. This work provides a facile approach to fabricating stable hydrophilic coating through a simple solvent exchange to reduce thrombosis and infection of biomedical catheters.

Fluorine-Containing, Self-Assembled Graft Copolymer for Tuning the Hydrophilicity and Antifouling Properties of PVDF Ultrafiltration Membranes

Neat poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes exhibit poor water permeance and surface hydrophobicity, resulting in poor antifouling properties. Herein, we report the synthesis of a fluorine-containing amphiphilic graft copolymer, poly(2,2,2-trifluoroethyl methacrylate)-g-poly(ethylene glycol) behenyl ether methacrylate (PTFEMA-g-PEGBEM), hereafter referred to as PTF, and its effect on the structure, morphology, and properties of PVDF membranes. The PTF graft copolymer formed a self-assembled nanostructure with a size of 7-8 nm, benefiting from its amphiphilic nature and microphase separation ability. During the nonsolvent-induced phase separation (NIPS) process, the hydrophilic PEGBEM chains were preferentially oriented towards the membrane surface, whereas the superhydrophobic PTFEMA chains were confined in the hydrophobic PVDF matrix. The PTF graft copolymer not only increased the pore size and porosity but also significantly improved the surface hydrophilicity, flux recovery ratio (FRR), and antifouling properties of the membrane. The membrane performance was optimal at 5 wt.% PTF loading, with a water permeance of 45 L m-2 h-1 bar-1, a BSA rejection of 98.6%, and an FRR of 83.0%, which were much greater than those of the neat PVDF membrane. Notably, the tensile strength of the membrane reached 6.34 MPa, which indicated much better mechanical properties than those reported in the literature. These results highlight the effectiveness of surface modification via the rational design of polymer additives and the precise adjustment of the components for preparing membranes with high performance and excellent mechanical properties.

Low-cost membrane from polyethylene terephthalate bottle waste for water purification and chromium removal: modification and application

River water has become contaminated with numerous hazardous compounds due to the rapid rise in population and industry expansion. Due to unchecked population growth and the improper disposal of electroplating industrial waste, issues with river water filtration and the elimination of chromium contamination have developed. Various technologies have been developed to overcome these problems. One of the technologies that have been proposed until now is membrane technology. On the other hand, the waste from plastic bottles, which grows yearly and now weighs 381.73 million tons, can create thin films or layers. Therefore, there is a lot of potential in employing plastic bottle trash as a low-cost, sustainable, and eco-friendly membrane material. In this study, the immersion-precipitation phase inversion method was used in the membrane preparation process from plastic bottle waste by modifying fillers (zeolite-NaY) and additives (LiCl and PEG-400) to improve membrane performance. The effect of filler and additive modification on the fabricated membrane was studied for its performance in water purification and chromium ion contaminant removal. The results demonstrated that the modified LiCl membrane performed optimally for water purification and the removal of chromium ions, along with a reduction in turbidity to 1.42 NTU (from 400 NTU) and a 54.75% removal of chromium.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

A Critical Review on the Feasibility of Synthetic Polymers Inclusion in Enhancing the Geotechnical Behavior of Soils

Polymers have attracted widespread interest as soil stabilizers and are proposed as an ecologically acceptable means for enhancing the geotechnical properties of soils. They have found profound applications in diverse fields such as the food industry, textile, medicine, agriculture, construction, and many more. Various polymers are proven to increase soil shear strength, improve volume stability, promote water retention, and prevent erosion, at extremely low concentrations within soils through the formation of a polymer membrane around the soil particles upon hydration. The purpose of this work is to provide an overview of existing research on synthetic polymers for soil improvement. A fundamental evaluation of many synthetic polymers used in soil stabilization is provided, Furthermore, the impact of different polymer types on the geotechnical parameters of treated soil was assessed and compared. Limiting factors like polymer durability and the effect of changing climatic conditions on the engineering behavior of the polymer-treated soils have been critically reviewed. The dominant mechanisms responsible for the alteration in the behavior of polymer-soil admixture are reviewed and discussed. This review article will allow practicing engineers to better understand the intrinsic and extrinsic parameters of targeted polymers before employing them in real-field scenarios for better long-term performance.

Preparation, Characterization and Tailoring Properties of Poly(Vinyl Chloride) Composites with the Addition of Functional Halloysite-Lignin Hybrid Materials

In this article, halloysite-lignin hybrid materials (HL) were designed and obtained. The weak hydrogen bonds found between the components were determined based on Fourier transform infrared spectroscopy (FTIR), proving the achievement of class I hybrid systems. The HL systems were characterized by very good thermal stability and relatively good homogeneity, which increased as the proportion of the inorganic part increased. This was confirmed by analyzing scanning electron microscope (SEM) images and assessing particle size distributions and polydispersity indexes. Processing rigid poly(vinyl chloride) (PVC) with HL systems with a content of up to 10 wt% in a Brabender torque rheometer allowed us to obtain composites with a relatively homogeneous structure confirmed by SEM observations; simultaneously, a reduction in the fusion time was noted. An improvement in PVC thermal stability of approximately 40 °C for composites with HL with a ratio of 1:5 wt/wt was noted. Regardless of the concentration of the HL system, PVC composites exhibited inconsiderably higher Young's modulus, but the incorporation of 2.5 wt% of fillers increased Charpy impact strength by 5-8 kJ/m² and doubled elongation at break. This study demonstrated that favorable mechanical properties of PVC composites can be achieved, especially with an HL system with a ratio of 5:1 wt/wt.

Cytocompatibility of MG-63 osteosarcoma cells on chitosan/hydroxyapatite/lignin hybrid composite scaffoldin vitro

This study aims at fabricating promising cytocompatible hybrid biocomposite scaffolds from chitosan (CS), hydroxyapatite (HAP) and lignin (L) for bone tissue engineering by using freeze-drying technique. Different ratios of HAP to L (50:0, 37.5:12.5, 25:25 and 12.5:37.5) were taken to determine the optimum ratio for obtaining a composite with superior properties. The mechanical and biological properties of the resulting composites were investigated. The mechanical results showed that the prepared composite with a ratio of 25:25 of HAP/L exhibited a remarkable enhancement in the mechanical properties compared to the others. Additionally, it was found from thein vitroresults that the addition of L enhanced the water uptake value of the resulting scaffolds indicating their increased hydrophilicity. As a result, a significant increase in the attachment and proliferation of MG-63 cell line (osteoblast like cells) was observed in composite scaffolds with L over the scaffold without L (CS/HAP). From these results, it could be suggested that the prepared composite scaffold with 25:25 of HAP/L is very promising biomaterials in bone tissue-engineering as it exhibited a better mechanical and biological properties than the other prepared composites.

Removal of naproxen and diclofenac using magnetic nanoparticles/nanocomposites

Magnetic iron oxide and iron/copper nanoparticles were synthesized using Lathyrus brachypterus extract, and then magnetic Fe₃O₄–CS, Fe₃O₄–AT, Fe/Cu–CS and Fe/Cu–AT nanocomposite beads were synthesized using chitosan and alginate natural polymers. They were used for both adsorption and heterogeneous catalysts for the catalytic wet peroxidation (CWPO) of naproxen (NPX), diclofenac (DCF) and NPX + DCF drugs which are important micro-organic pollutants, separately and together (NPX + DCF) from aqueous media. In adsorption studies, the drugs were adsorbed very quickly in the first minutes and then, desorbed in between 8 and 10 min. In competitive adsorption, the adsorbents showed selective properties for DCF and NPX. In CWPO technique, drug removal was achieved in 9 min with a conversion capacity of 92% for DCF with Fe/Cu–CS and 84% for NPX with Fe/Cu–AT optimum experimental conditions, such as pH 5, 30% of H₂O₂, 100 mg catalyst and 298 K. Based on reusability of the catalysts, it was seen that there was a slight decrease in the removal efficiencies in the third cycle and the stable and active structure of the catalyst was preserved to the desired extent. Furthermore, the oxidation reaction was in good agreement with the pseudo-first-order kinetic model.

Ultra-low pressure PES ultrafiltration membrane with high-flux and enhanced anti-oil-fouling properties prepared via in-situ polycondensation of polyamic acid

Polyamic acid (PAA) is a flexible polymer and has abundant valuable hydrophilic groups. Herein, we developed an ultra-low pressure ultrafiltration (UF) membrane by integrating PAA into the polyethersulfone (PES) matrix via the "in-situ polycondensation" method. PAA was well compatible with PES and distributed uniformly in the membrane. The introduction of PAA improved membrane hydrophilicity. Meanwhile, the membrane pore structures were also refined. The membrane exhibited an excellent permeability under ultra-low pressure due to its improvement of hydrophilicity and pore structures. Under 0.3 bar, compare with the water flux of PES membrane, PES/PAA membrane improved nearly 2 times (571.05 L/(m²·h)), with a high BSA rejection (≥90%). Even under a lower pressure, 0.1 bar, >300 L/(m²·h) still can be achieved. Interestingly, the membrane we developed could maintain a high performance after drying, and then is very suitable for dry preservation. PES/PAA membrane showed a high oil removal (≥92%) and could remove oil from water effectively. Besides, the membrane exhibited excellent anti-oil-fouling properties. The flux recovery rate of PES/PAA (70.0%) far exceeds that of PES (37.9%) after three filtration and cleaning cycles. The membrane we developed is very valuable in oily wastewater treatment.

Unveiling the Impacts of Sodium Hypochlorite on the Characteristics and Fouling Behaviors of Different Commercial Polyvinylidene Fluoride Hollow Fiber Membranes

Sodium hypochlorite (NaOCl) is a commonly used cleaning agent for recovering membrane performance in membrane technologies. A thorough understanding of the impacts of NaOCl exposure on membrane properties and fouling behavior is important for optimizing chemical cleaning process and extending membrane lifespan. In this study, three commercial polyvinylidene fluoride (PVDF) hollow fiber ultrafiltration membranes (SMM-1010, MEMCOR^® CS II and ZeeWeed 500) were used to systematically explore the effects of NaOCl dose and solution pH (8 and 10) on membrane properties. The results showed that membrane pores increased with exposure time prolonging, and more pores were observed at pH 8 aging condition. The amide group in the Fourier transformation infrared spectra was disappeared, while the carboxylic acid and succinimide groups were formed at pH 10 and pH 8 conditions, respectively. The hydrophilicity and pure water permeability (PWP) of SMM-1010 and MEMCOR^® CS II membranes had insignificant changes during NaOCl aging process, whereas the hydrophilicity of ZeeWeed 500 membrane slightly decreased and its PWP increased by 1.4-fold. The antifouling properties of NaOCl-aged SMM-1010 and MEMCOR^® CS II membranes were slightly improved, whereas the NaOCl-aged ZeeWeed 500 membrane showed severer flux decline with humic acid filtration. Our findings could provide guidance for practical chemical cleaning process optimization.

Membranes for Oil/Water Separation: A Review

Recent advancements in separation and membrane technologies have shown a great potential in removing oil from wastewaters effectively. In addition, the capabilities have improved to fabricate membranes with tunable properties in terms of their wettability, permeability, antifouling, and mechanical properties that govern the treatment of oily wastewaters. Herein, authors have critically reviewed the literature on membrane technology for oil/water separation with a specific focus on: 1) membrane properties and characterization, 2) development of various materials (e.g., organic, inorganic, and hybrid membranes, and innovative materials), 3) membranes design (e.g., mixed matrix nanocomposite and multilayers), and 4) membrane fabrication techniques and surface modification techniques. The current challenges and future research directions in materials and fabrication techniques for membrane technology applications in oil/water separation are also highlighted. Thus, this review provides helpful guidance toward finding more effective, practical, and scalable solutions to tackle environmental pollution by oils.

PVDF/MOFs mixed matrix ultrafiltration membrane for efficient water treatment

Polyvinylidene fluoride (PVDF), with excellent mechanical strength, thermal stability and chemical corrosion resistance, has become an excellent material for separation membranes fabrication. However, the high hydrophobicity of PVDF membrane surface normally leads a decreased water permeability and serious membrane pollution, which ultimately result in low operational efficiency, short lifespan of membrane, high operation cost and other problems. Metal-organic frameworks (MOFs), have been widely applied for membrane modification due to its large specific surface area, large porosity and adjustable pore size. Currently, numerous MOFs have been synthesized and used to adjust the membrane separation properties. In this study, MIL-53(Al) were blended with PVDF casting solution to prepare ultrafiltration (UF) membrane through a phase separation technique. The optimal separation performance was achieved by varying the concentration of MIL-53(Al). The surface properties and microstructures of the as-prepared membranes with different MIL-53(Al) loading revealed that the incorporation of MIL-53(Al) enhanced the membrane hydrophilicity and increased the porosity and average pore size of the membrane. The optimal membrane decorated with 5 wt% MIL-53(Al) possessed a pure water permeability up to 43.60 L m-2 h-1 bar-1, while maintaining higher rejections towards BSA (82.09%). Meanwhile, the prepared MIL-53(Al)/LiCl@PVDF membranes exhibited an excellent antifouling performance.

A novel approach using protein-rich biomass as co-fermentation substrates to enhance phosphorus recovery from FePs-bearing sludge

A novel approach for the enhancement of phosphorus (P) recovery from Fe bound P compounds (FePs)-bearing sludge by co-fermentation with protein-rich biomass (PRB) is reported. Four PRBs (silkworm chrysalis meal, fish meal, corn gluten meal, and soya bean meal) were used for co-fermentation. The results revealed that PRBs with strong surface hydrophobicity and loose structure favored the hydrolysis and acidogenesis processes. Sulfide produced by PRB could react with FePs to form FeS and promote P release. Due to the neutralization of volatile fatty acids (VFAs) by a relatively high concentration of ammonia, the pH was maintained near neutral and thus prevented the dissolution of metal ions (e.g., Fe and Ca). This was beneficial to save the cost of subsequent P recovery and form high-purity struvite. Compared with the control, the soluble orthophosphate and VFAs increased by 88.3% and 531.3%, respectively, in the co-fermentation system with silkworm chrysalis meal. Cysteine was the important intermediate. The metagenomics analysis indicated that the gene abundances of phosphate acetyltransferase and acetate kinase, which were key enzymes in the acetate metabolism, increased by 117.7% and 52.2%, respectively. The gene abundances of serine O-acetyltransferase and cysteine synthase increased by 63.4% and 54.4%, respectively. Cysteine was primarily transformed to pyruvate and sulfide. This study provides an environment-friendly strategy to simultaneously recover P and VFAs resources from FePs-bearing sludge and PRB waste.

Fabrication of an antifouling PES ultrafiltration membrane via blending SPSF

Sulfonated polysulfone (SPSF) with different sulfonation degrees (10%, 30%, and 50%) was added to polyethersulfone (PES) to improve the separation and antifouling performance of polyethersulfone ultrafiltration membranes. The PES/SPSF blend ultrafiltration membrane was prepared by the non-solvent induced phase inversion method (NIPS), and the effect of sulfonation degree on the ultrafiltration performance was studied. The compatibility of SPSF and PES was calculated by the group contribution method, and confirmed by differential scanning calorimetry (DSC). The morphology and surface roughness of the membrane were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), the chemical composition of the membrane was analyzed by X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (FTIR), and the permeability and anti-fouling performance of the blend membrane were studied through filtration experiments. The research shows that the flux and anti-fouling performance of the blend membrane have been improved after adding SPSF. When the sulfonation degree of the SPSF is 30%, the pure water flux of the blend membrane can reach 530 L m⁻² h⁻¹, the rejection rate of humic acid (HA) is 93%, the flux recovery rate of HA increases from 69.23% to 79.17%, and the flux recovery rate of BSA increases from 72.56% to 83%.

The chemical structures of (a) PES and (b) SPSF.

Conversion of Plastic Waste into Supports for Nanostructured Heterogeneous Catalysts: Application in Environmental Remediation

Plastics are ubiquitous in our society and are used in many industries, such as packaging, electronics, the automotive industry, and medical and health sectors, and plastic waste is among the types of waste of higher environmental concern. The increase in the amount of plastic waste produced daily has increased environmental problems, such as pollution by micro-plastics, contamination of the food chain, biodiversity degradation and economic losses. The selective and efficient conversion of plastic waste for applications in environmental remediation, such as by obtaining composites, is a strategy of the scientific community for the recovery of plastic waste. The development of polymeric supports for efficient, sustainable, and low-cost heterogeneous catalysts for the treatment of organic/inorganic contaminants is highly desirable yet still a great challenge; this will be the main focus of this work. Common commercial polymers, like polystyrene, polypropylene, polyethylene therephthalate, polyethylene and polyvinyl chloride, are addressed herein, as are their main physicochemical properties, such as molecular mass, degree of crystallinity and others. Additionally, we discuss the environmental and health risks of plastic debris and the main recycling technologies as well as their issues and environmental impact. The use of nanomaterials raises concerns about toxicity and reinforces the need to apply supports; this means that the recycling of plastics in this way may tackle two issues. Finally, we dissert about the advances in turning plastic waste into support for nanocatalysts for environmental remediation, mainly metal and metal oxide nanoparticles.

Metal oxide and carbon nanomaterial based membranes for reverse osmosis and membrane distillation: A comparative review

Commercial membranes typically suffer from fouling and wetting during membrane distillation (MD). In contrast, reverse osmosis (RO) can be subject to the fouling issue if applied for highly saline feed solutions containing foulants (e.g., organics, oils, and surfactants). Among the diverse treatment options, the nanomaterial-based membranes have recently gained great interest due to their advantageous properties (e.g., enhanced flux and roughness, better pore size distribution, and higher conductivity). This review focuses on recent advances in the mechanical properties, anti-fouling capabilities, salt rejection, and economic viability of metal oxide (SiO₂, TiO₂, and ZnO) and carbon nanomaterial (graphene oxide/carbon nanotube)-based membranes. Current challenges in applying nanomaterial-based membranes are also discussed. The study further describes the preparation methods, mechanisms, commercial applications, and economical feasibility of metal oxide- and carbon nanomaterial-based membrane technologies.

Universal Intraductal Surface Antifouling Coating Based on an Amphiphilic Copolymer

Surface modification on the inner wall of medical or industrial polymeric catheters with a high length/diameter ratio is highly desired. Herein, a universal and facile method based on an amphiphilic copolymer was developed to immobilize an intraductal surface antifouling coating for a variety of polymeric catheters. A fouling-repelled thin layer was formed by swelling-driven adsorption via directly perfusing an amphiphilic copolymer [polyvinylpyrrolidone-polydimethylsiloxane-polyvinylpyrrolidone (PVP-PDMS-PVP)] solution into catheters. In this copolymer, hydrophobic PDMS was embedded into a shrinking cross-linked network of catheters; also, PVP segments migrated to the surface under driving water to form a hydrophilic antifouling coating. Moreover, because of the coordination between I₂ and pyrrolidone of PVP, the copolymer-modified intraductal surface was then infused with aqueous I₂ to form the PVP-I₂ complex, endowing this coating with bactericidal activity. Notably, diverse catheters with arbitrary shapes (circular, rectangular, triangular, and hexagonal) and different components (silicone, polyurethane, and polyethylene) were also verified to work using this interfacial interpenetration strategy. The findings in this work provide a new avenue toward facile and universal fabrication of intraductal surface antifouling catheters, creating a superior option for decreasing the consumable costs in industrial production and alleviating the pain of replacing catheters for patients.

Research and application progress of lignin-based composite membrane

In view of the serious environmental pollution, which is the greatest problem the world is facing, and the continuous consumption of raw materials, it is imminent to search for green and sustainable resources. Lignin is an organic polymer that exists widely in nature, and if it can be transformed from traditional low-value waste product with low range of applications to functional materials with high application prospects, it can be of great significance to alleviate environmental pollution and shortage of fossil resources. One of the functional applications of lignin involves its use to fabricate composite with other polymeric materials, which can then be used to prepare membrane materials. This review summarizes the recent research and application progress of combining lignin with polypropylene, polyvinyl alcohol, starch, cellulose, chitosan, and other polymeric materials to prepare composite membranes; and summarizes the future development direction of lignin-based composite membranes. We hope this review may provide a new perspective to the understanding of lignin-based composite membranes and a useful reference for future research.

Probing the aging processes and mechanisms of microplastic under simulated multiple actions generated by discharge plasma

Microplastics (MPs) are becoming one class of pollutants with high global concerns. Information regarding aging behaviors of MPs in complicated natural conditions is still lacking due to the very slow aging processes. In this study, discharge plasma oxidation was applied to simulate the various radical oxidation and physical effects naturally occurring in the environment to shed light on the aging behaviors and mechanisms of MPs, with polyvinyl chloride microplastic (PVC-MP) as a model. The surface morphology, particle size, specific surface area, crystallinity, and chemical compositions of PVC-MP were comprehensively characterized as a result of aging. The aging degree indicated by carbonyl index and oxygen-to-carbon ratio increased with the plasma oxidation intensity and duration. The aged PVC-MP was characterized as more O-containing functional groups, smaller particle size, larger specific surface area, higher hydrophilicity, and higher crystallinity. Consequently, the aged PVC-MP provided more sites for adsorption of tetrabromobisphenol (TBBPA) in solutions by forming hydrogen-bonds, and electrostatic force. The changes in the properties of the aged PVC-MP, and the strong adsorption with TBBPA led to unexpected synergistic toxic effects to Scenedesmus obliquus. The results provide direct evidences of aging processes of MPs and the potential environmental risks due to aging in the environment.