Highly efficient ultrasonic-assisted pre-concentration and simultaneous determination of trace amounts of Pb (II) and Cd (II) ions using modified magnetic natural clinoptilolite zeolite: Response surface methodology

Separation and enrichment of Cd and Pb from food and water samples based on a graphene oxide-decorated poly 2-diethylaminoethyl methacrylate nanocomposite by dispersive micro-solid phase extraction (d-μ-SPE)

In this study, a graphene oxide combined with poly(2-diethylaminoethyl methacrylate) (GO@PDEAEMA) nanocomposite was synthesized for the separation and enrichment of Cd and Pb from food and water samples using the dispersive micro-solid phase extraction (d-μ-SPE) technique. The GO@PDEAEMA nanocomposite was synthesized using surface-initiated atom transfer radical polymerization (SI-ATRP) and characterized using various analytical techniques, such as FTIR, FE-SEM, TGA, BET, and XRD. The optimal experimental conditions were pH 8, 0.5 M HNO₃ as eluent, 5 mg of sorbent, and adsorption/desorption times of 0.5 and 1 min, respectively, with a recovery range of 89-101 %. The suggested method showed low limits of detection (LOD) and quantification (LOQ) of 0.11 μg L-1 and 0.37 μg L-1 for Cd and 0.28 μg L-1 and 0.93 μg L-1 for Pb, respectively. The optimal procedure was successfully applied to real water and food samples. The study demonstrates the possibility of using GO@PDEAEMA nanocomposite as an effective sorbent for toxic metal extraction.

Extraction and preconcentration of lead (II) in various water and food samples by orbital shaker-assisted magnetic solid phase extraction method using a new magnetic poly linoleic acid-polystyrene-PDMS block copolymer

The aim of this study was to develop a practical orbital shaker-assisted magnetic solid phase extraction (OSA-MSPE) method for the determination of lead by FAAS. A new magnetic poly linoleic acid-polystyrene-polydimethylsiloxane (PSt-PLina-PDMS) hydrophobic graft copolymer was synthesized and characterized by NMR, FT-IR, SEM-EDX, DSC, TGA, BET and used as adsorbent for the extraction of Pb (II). This adsorbent can be used at least 50 times without any decrease of its adsorption properties for the adsorption and elution of analyte ions. Several analytical parameters including pH, adsorbent amount, sample volume, shaking time, etc. were optimized. Multivariate optimization was used for the investigation of different parameters. The linear range at optimum operating condition was 1.7-84 μg L-1. The limit of detection (LOD) and limit of quantification (LOQ) were 0.5 μg L-1, 1.7 μg L-1, respectively. Intraday and interday relative standard deviation (RSD %), enhancement factor (EF) and adsorbent capacity were found as 1.9%, 3.3%, 166.7, 50 mg g-1, respectively. OSA-MSPE method was tested with certified reference materials including LGC-6010 (Hard Drinking Water), NCS ZC73032 Celery and CS-M-3 Control Sample Microelements in Mushroom Powder for the accuracy. Experimental results for lead were confirmed with certified values. Present method was successfully applied to various liquid and solid food samples. The OSA-MSPE method has some important features such as selective, sensitive, low LOD, LOQ and RSD, pre-concentration factor (PF) and high enhancement factor (EF). High tolerance limits against matrix ions were achieved.

Development of smartphone-controlled and machine-learning-powered integrated equipment for automated detection of bioavailable heavy metals in soils

Rapid and accurate on-site detection of crop-absorbable cadmium (Cd) and lead (Pb) in soils is important for food security and human health. The automated soil sample pretreatment method, including the ultrasonic extraction of weakly acid-soluble heavy metals, suction-filtration, and UV photolysis, was proposed to achieve the high-efficiency preparation from soil sample to extract solution. Bismuth-film-modified glass carbon electrode combined with the homemade potentiostat was fabricated to implement the square-wave anodic stripping voltammetry (SWASV) measurements of soil extracts. The peak-information-acquisition algorithm was designed to automatically obtain peak heights and widths of Zn2+, Cd2+, Pb2+, Bi3+, and Cu2+ stripping currents, and then which were used as input variables for establishing machine-learning models to enhance the detection accuracy of SWASV to Cd2+ and Pb2+ under the coexistence of multiple heavy metal ions. Eventually, the smartphone-controlled integrated-automated detection equipment was developed and successfully applied to the automatic pretreatment of soil samples and the determination of weakly acid-soluble Cd2+ and Pb2+ in real soil samples. The detection speed was 75 min/sample, and the detection results were close to the standard method (BCR-ICP-MS). This equipment can provide powerful technical support for on-site rapid and accurate determination of crop-absorbable heavy metals in soils.

The application progress of magnetic solid-phase extraction for heavy metal analysis in food: a mini review

The emerging sample pretreatment technique of magnetic solid-phase extraction (MSPE) has drawn the attention of researchers owing to its advantages of less reagent consumption, fast separation/enrichment process, high adsorption capacity, and simple operation. This paper presents a review of synthesis techniques, classification, and analysis procedures for MSPE in the detection of heavy metals in food. Magnetic adsorbents derived from silica, metal oxides, carbon, polymers, etc., are applied for the detection of heavy metals in food. Then, the recent development of the technology of MSPE for the analysis of heavy metal extraction in food is summarized in detail. Finally, the future outlook for the improvement of MSPE is also discussed.

Functional Materials for Water Restoration: A "Fish Cage" for Efficient Capture of Pb(II) Ions

In this work, a "fish cage" material for trapping Pb(II) ions has been successfully obtained, which is a novel clathrate functionalized metal-oganic framework (Cage-MOF) by introducing free adsorption sites (SO42-). The three-dimensional (3D) cage structure of Cage-MOF gives it a larger contact area and can capture "swimming fish" (Pb(II)) like a "fishing cage" in a water solution. This is the first high-efficiency adsorption material obtained by introducing free coordination groups. Cage-MOF not only has excellent water stability but also improves the selectivity and affinity for Pb(II) ions in water because of the presence of sulfate adsorption sites, and its adsorption capacity is as high as 806 mg/g. This work shows a novel and effective idea for the synthesis of water restoration materials.

Recent progresses, challenges, and opportunities of carbon-based materials applied in heavy metal polluted soil remediation

The application of carbon-based materials (CBMs) for heavy metal polluted soil remediation has gained growing interest due to their versatile properties and excellent remediation performance. Although the progresses on applications of CBMs in removing heavy metal from aqueous solution and their corresponding mechanisms were well known, comprehensive review on applications of CBMs in heavy metal polluted soil remediation were less identified. Therefore, this review provided insights into advanced progresses on utilization of typical CBMs including biochar, activated carbon, graphene, graphene oxide, carbon nanotubes, and carbon black for heavy metal polluted soil remediation. The mechanisms of CBM remediation of heavy metals in soil were summarized, mainly including physical adsorption, precipitation, complexation, electrostatic interaction, and cationic-π coordination. The key factors affecting the remediation effect include soil pH, organic matter, minerals, microorganisms, coexisting ions, moisture, and material size. Disadvantages of CBMs were also included, such as: potential health risks, high cost, and difficulty in achieving co-passivation of anions and cations. This work will contribute to our understanding of current research advances, challenges, and opportunities for CBMs remediation of heavy metal-contaminated soils.

Zeolites: A series of promising biomaterials in bone tissue engineering

As an important worldwide medical issue, bone defect exhibits a variety of physical and psychological consequences on sufferers. Some features of clinical treatments including bone grafting and limb shortening are not satisfactory. Recently, bone tissue engineering has been considered as the most effective approach to dealing with the issue of bone deformities. Meanwhile, a variety of biomaterials have been rationally designed and created for the bone regeneration and tissue repairing. Among all these admirable biomaterials for bone remodeling, zeolite-based materials can serve as efficient scaffold candidates with excellent osteo-inductivity. In addition, the porous nature and high biocompatibility of zeolites endow them with the ability as ideal substrates for cell adhesion and proliferation. More importantly, zeolites are investigated as potential coating materials for implants because they have been proven to increase osteo-conductivity and aid in local elastic modeling. Last but not least, zeolites can also be used to treat bone disorders and act as dietary supplements during the practical applications. Accordingly, numerous benefits of zeolite prompt us to summarize their recent biomedical progress including but not limited to the distinguishing characteristics, broad classifications, as well as promising usages in bone tissue engineering.

Adsorption of Heavy Metals in Contaminated Water Using Zeolite Derived from Agro-Wastes and Clays: A Review

Due to climate change and anthropogenic activities such as agriculture, mining, and urbanization, water contamination has become a very real modern problem. Modern solutions such as activated carbon, reverse osmosis, and ultrafiltration, among others, have been employed in the decontamination of water. These methods are, however, expensive to set up and maintain and therefore have proved a challenge to implement in developing countries. Zeolite materials exhibit excellent structural properties, such as high ion exchange capacity, porosity, and relative surface area, which make them attractive to water decontamination processes. However, conventional zeolites are expensive, and recent research has focused on utilizing low-cost materials such as agro-wastes and clays as raw materials for the synthesis of zeolites. This review aims to discuss the role of low-cost zeolites in their removal of heavy metals and the feasibility of agro-wastes and natural clays in the synthesis of zeolites. Recent research studies based on the synthesis of zeolites from clays and agro-wastes and their application in heavy metal removal have been reviewed and discussed. Agro-wastes such as rice husk ash and sugarcane bagasse ash and layered silicate clays such as kaolinite and smectites are particularly of interest to zeolite synthesis due to their high silica to alumina ratio. Zeolites synthesized through various methods such as hydrothermal, molten salt, and microwave irradiation synthesis have been discussed with their effect on the adsorption of various heavy metals.

Production of biodiesel from salvia mirzayanii oil via electrolysis using KOH/Clinoptilolite as catalyst

BACKGROUNDS

In recent years, fossil fuels are the main energy supply in both transportation and industry. Their increasing consumption has been causing global warming and acid raining. One of the alternative fuels that is considered today is biodiesel, which is clean and eco-friendly. The main method for biodiesel production is transesterification reaction of triglyceride oil with methanol in the presence of a suitable catalyst.

METHOD

In this research, biodiesel was produced from Salvia mirzayanii oil in the presence of KOH/Clinoptilolite catalyst. The impregnation, hydrothermal, and incipient wetness methods were used for loading KOH on the Clinoptilolite support to produce biodiesel via electrolysis method. The characteristics of the KOH/Clinoptilolite catalyst were examined through scanning electron microscopy (SEM), energy dispersive X-ray Spectroscopy (EDX), X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) analyses. The effects of key parameters including catalyst amount, methanol to oil molar ration, reaction time, reaction temperature, co-solvent type and its proportion, electrolysis voltage, catalyst reusability, and KOH concentration were examined on the biodiesel yield.

RESULTS

The results of elemental analysis confirmed that KOH was well loaded on Clinoptilolite support. The highest yield of biodiesel was obtained 79% in the presence of 10 wt% catalyst, alcohol to oil ratio of 9:1, acetone concentration of 10 wt%, temperature of 60 °C, and voltage of 10 V. The results of GC-MS, FTIR and H-NMR analyses illustrated that biodiesel as a product was produced with good quality.

CONCLUSION

Based on the obtained results, in all three methods of catalyst synthesis KOH was loaded on Clinoptilolite support but at the end of the transesterification reaction only the catalyst synthesis via incipient wetness method could be reused three times under optimum reaction conditions. The produced biodiesel had high quality, whose physical and chemical properties had good agreement with ASTM, EN 14214, IS 15607 standards. Since the salvia mirzayanii oil is an appropriate feedstock source for biodiesel production, it is suggested to use salvia mirzayanii oil and KOH/Clinoptilolite catalyst to produce biodiesel on industrial scale.

A Novel Coordination Polymer as Adsorbent Used to Remove Hg(II) and Pb(II) from Water with Different Adsorption Mechanisms

Under the hydrothermal condition, a new type of two-dimensional coordination polymer ([Cd(D-Cam)(3-bpdb)]_n, Cd-CP) has been constructed. It is composed of D-(+)-Camphoric-Cd(II) (D-cam-Cd(II)) one-dimensional chain and bridging 1,4-bis(3-pyridyl)-2,3-diaza-1,3-butadiene (3-bpdb) ligands. Cd-CP has a good removal effect for Hg(II) and Pb(II), and the maximum adsorption capacity is 545 and 450 mg/g, respectively. Interestingly, thermodynamic studies have shown that the adsorption processes of Hg(II) and Pb(II) on Cd-CP use completely different thermodynamic mechanisms, in which the adsorption of Hg(II) is due to a strong electrostatic interaction with Cd-CP, while that of Pb(II) is through a weak coordination with Cd-CP. Moreover, Cd-CP has a higher affinity for Hg(II), and when Hg(II) and Pb(II) coexist, Cd-CP preferentially adsorbs Hg(II).

Okara and okara modified and functionalized with iron oxide nanoparticles for the removal of Microcystis aeruginosa and cyanotoxin

Eutrophicating compounds promote the growth of cyanobacteria, which has the potential of releasing toxic compounds. Alternative raw materials, such as residues, have been used in efficient adsorption systems in water treatment. The aim of the present study was to apply the residue Okara in its original form and modified by hydrolysis with immobilization of magnetic nanoparticles as an adsorbent. For the removal, the cyanobacteria Microcystis aeruginosa was chosen, as well as its secondary metabolites, L-amino acids leucine and arginine (MC-LR microcystin), from aqueous solutions. The adsorbents presented a negative surface charge, and the x-ray diffraction (DRX) outcomes successfully demonstrated the immobilization of iron oxide nanoparticles on the adsorbents. The adsorbent with the best result was the Okara hydrolyzed and functionalized with iron oxide, which showed a 47% (qe = 804.166 cel/g) and 85% (qe = 116.94 µg/L) removal for the cyanobacteria cells and chlorophyll-a, respectively. The kinetics study demonstrated a pseudo-first-order adsorption with maximal adsorption in 480 minutes, removing 761 µg/L of chlorophyll-a. In this trial, a low organic material removal has occurred, with a removal rate of 5% (qe = 0.024 mg/g) in the analysis of compounds in absorbance by ultraviolet light (UV) monitored by optical density determination in 254 nm (OD254). Nevertheless, the reaction system with the presence of organic material removed 53,28% of the MC-LR toxin, with adsorption capacities of 2.84 µg/L in a preliminary trial conducted for two hours, arising as a potential and alternative adsorbent with a capacity of removing cyanobacteria and cyanotoxin cells simultaneously.

Banana stem and leaf biochar as an effective adsorbent for cadmium and lead in aqueous solution

Lead (Pb) and cadmium (Cd) are toxic heavy metals commonly found in aqueous environments. Biochar as a green adsorbent generated from biomass feedstock may be used for effective removal of these heavy metals. This study investigated the adsorption kinetics and isotherms of Pb2+ and Cd2+ in aqueous solutions at different pH by biochar prepared from banana stem and leaf (BSL-BC) at 400 °C. Characterizations using scanning electron microscope, X-ray diffraction, and Fourier-transform infrared spectroscopy showed that the synthesized BSL-BC had rough surface, porous structure, and oxygen-containing functional groups. The adsorption of Pb2+ and Cd2+ onto BSL-BC reached equilibrium in 8 h and 200 min, respectively, with faster adsorption attained at higher pH and the optimum pH occurred at 5 (Pb2+) and 8 (Cd2+). All adsorption kinetic data followed the pseudo-second-order rate model. The adsorption isotherm data of Pb2+ and Cd2+ could be well-described by the Langmuir and Freundlich models, respectively, whereas neither the Temkin or Dubinin-Radushkevich models provided satisfactory fitting results. The maximum adsorption capacities for Pb2+ and Cd2+ were 302.20 and 32.03 mg/g, respectively. The calculated mechanism contributions showed that complexation with oxygen-containing functional groups, ion exchange, mineral precipitation, and Pb2+/Cd2+-π coordination accounted for 0.1%, 8.4%, 88.8%, and 2.6% to Pb2+ adsorption, and 0.4%, 6.3%, 83.0%, and 10.4% to Cd2+ adsorption, respectively. Therefore, mineral precipitation was likely the major mechanism responsible for adsorption of both Pb2+ and Cd2+ by BSL-BC. The results suggest that the synthesized BSL-BC has great potential for adsorption of Pb2+ and Cd2+ from aqueous solutions.

Preparation of clinoptilolite/starch/CoFe2O4 magnetic nanocomposite powder and its elimination properties for cationic dyes from water and wastewater

A new magnetic nanocomposite clinoptilolite (CLT)/Starch/CoFe₂O₄ was synthesized using co-precipitation method. The prepared magnetic composite powder was utilized for decontamination of methylene blue dye (MBD), methyl violet dye (MVD), and crystal violet dye (CVD) from water media. The BET analysis showed that CLT modification using starch and CoFe₂O₄ nanoparticles improved its specific surface and the amount of specific surface area for CLT, CoFe₂O_4, and CLT/Starch/CoFe₂O₄ powder was reported to be 18.82 m².g^-1, 151.4 m².g^-1, and 104.75 m².g^-1, respectively. Experimental results showed that pH 9 had a vital role in the adsorption process of all three types. Langmuir and Redlich-Petersen isotherm models were well fitted with experimental data. Also, the maximum adsorption capacity of CVD, MBD, and MVD to the desired composite was determined as 32.84 mg.g^-1, 31.81 mg.g^-1, and 31.15 mg.g^-1, respectively. In addition, the kinetic data of the removal process followed a pseudo-first order (PFO) kinetic model. Negative thermodynamic parameters were indicated that the process is spontaneous and exothermic. Finally, ad(de)sorption experiments' results showed that the synthesized nanocomposite adsorbent has an excellent ability to adsorb cationic dyes after several consecutive cycles.

Laboratory and simulation study on the Cd(Ⅱ) adsorption by lake sediment: Mechanism and influencing factors

Sediments are the major sinks for Cd(Ⅱ) in the aquatic environment. Here, the detailed binding mechanisms and effects of environmental factors on Cd(Ⅱ) adsorption onto lake sediment were tested by a batch of adsorption and characteristic experiments. Sediment samples and sediment-Cd complexes were characterized using Scanning electron microscopy, Energy dispersive spectroscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction spectral analyses. The interactive and main effect of parameters such as pH, flow velocity, Cd(II) concentration, sediment particle size, humic acid, fulvic acid and adsorption time involved in the adsorption process were determined using two models based on response surface methodology (RSM) and a back-propagation neural network with genetic algorithm (GABP). Results showed that Cd(II) adsorption onto sediment was mainly achieved through surface complexation with O-containing groups and precipitation with carbonate and sulfide. RSM was favorable for modeling Cd(II) adsorption in lake systems because it intuitively reflected the influence of the factors and had a good fitting precision (R² = 0.8838, RSME = 2.5496) close to that of the GABP model (R² = 0.8959, RSME = 2.5410). pH, sediment particle size, and humic acid exerted strong influences on Cd(II) immobilized by the sediment. Overall, our findings facilitate a better understanding of Cd(II) mobility in lakes and provide a reference for controlling heavy metals derived from both aqueous and sediment sources.

An Efficient and Stable Perovskite Solar Cell with Suppressed Defects by Employing Dithizone as a Lead Indicator

The defects in perovskite films are one of the most non-negligible factors that can attenuate the performances of perovskite solar cell. This work fabricates defect-reduced perovskite film by using the lead indicator (dithizone) as an additive of perovskite functional layer. The dithizone can retard the crystallization rate of perovskite films, passivate the defects, and enhance the structure stability of perovskite by coordinating with lead atoms. As a result, the device doped with dithizone yields outstanding power conversion efficiency and stability.

Cadmium adsorption behavior of porous and reduced graphene oxide and its potential for promoting cadmium migration during soil electrokinetic remediation

In this study, a porous reduced graphene oxide (PRGO) carbon nanomaterial was successfully obtained by activation of natural graphite with KOH at high temperature and was applied as an auxiliary electrode in soil electrokinetic remediation to investigate the promoting effect on Cd migration. We found that PRGO contained a large amount of oxygen-containing groups (hydroxyl and carboxyl groups) and exhibited high Cd²⁺ adsorption efficiency at pH values above 4, achieving a maximum adsorption capacity of 434.78 mg/g for Cd. In addition, PRGO could selectively adsorb Cd, Pb, Cu, and Zn but not K, Na, or Mg from soil solution. The electrokinetic remediation experiment showed that the PRGO auxiliary electrode promoted the migration of Cd and effectively controlled the increase in soil pH near the cathode, possibly due to ion exchange between the surface functional groups on the auxiliary electrode and Cd²⁺. In addition, the location of the PRGO auxiliary electrode strongly influenced the migration of Cd. For instance, the soil Cd concentration of treatment H-5 was 57.86% lower than that of H-0 at a distance of 5-10 cm from the electrode; however, the soil Cd concentration measured at 0-5 cm for treatment H-5 was 34.84% higher than that of treatment H-0. Our study demonstrated that PRGO could be applied as an auxiliary electrode to promote Cd migration during electrokinetic remediation of Cd-contaminated soil.

Magnetic metal organic framework for pre-concentration of ampicillin from cow milk samples

The aim of this study is a present of a simple solvothermal synthesis approach to preparation of Cu-based magnetic metal organic framework (MMOF) and subsequently its application as sorbent for ultrasound assisted magnetic solid phase extraction (UAMSPE) of ampicillin (AMP) from cow milk samples prior to high performance liquid chromatography-Ultraviolet (HPLC-UV) determination. Characteristics of prepared MMOF were fully investigated by different techniques which showed the exclusive properties of proposed sorbent in terms of proper functionality, desirable magnetic property and also high specific surface area. Different influential factors on extraction recovery including sorbent dosage, ultrasonic time, washing solvent volume and eluent solvent volume were assessed using central composite design (CCD) based response surface methodology (RSM) as an operative and powerful optimization tool. This is the first report for determination of AMP using MMOF. The proposed method addressed some drawbacks of other methods and sorbents for determination of AMP. The presented method decreases the extraction time (4 min) and also enhances adsorption capacity (250 mg/g). Moreover, the magnetic property of presented sorbent (15 emu/g) accelerates the extraction process which does not need filtration, centrifuge and precipitation procedures. Under the optimized conditions, the proposed method is applicable for linear range of 1.0–5000.0 μg/L with detection limit of 0.29 μg/L, satisfactory recoveries (≥95.0%) and acceptable repeatability (RSD less than 4.0%). The present study indicates highly promising perspectives of MMOF for highly effective analysis of AMP in complicated matrices.

•

MMOF was prepared and used for the first time for determination of ampicillin from cow milk samples.

•

The extraction method was convenient, rapid and the MMOF can be used more than 8 times.

•

The MMOF have high specific surface area (300.0 m²/g) and high adsorption capacity (250.5 mg g⁻¹).

•

The separation time was only 5 min, which was much shorter than other reported.