Electrodeposition of Ag nanodendrites SERS substrates for detection of malachite green

Polyethyleneimine-assisted one-pot synthesis of Au nanodendrites on carbon nanotube sheet as an efficient SERS substrate

A polyethyleneimine (PEI)-assisted simple and efficient one-pot hydrothermal reduction method is reported to prepare high-quality gold nanodendrites (AuNDs) on a carbon nanotube (CNT) sheet. We observed that the prepared AuNDs have a well-defined backbone-multiple branching structure. With the systematical investigation of the growth mechanism, it was found that the bromide (Br-) ion concentration has an essential effect on the formation of AuNDs. By evaluating the growth conditions of AuNDs, it was demonstrated that PEI attached on the surface of CNT sheet plays multiple crucial roles as a reducing agent, stabilizer, and structure director in the formation of AuNDs. The prepared CNT-AuNDs hybrid was employed as a flexible surface-enhanced Raman scattering (SERS) substrate to detect the analyte Congo red (CR). Due to the unique structure of AuNDs, such as 3-D branches, rough surface, and sharp edges, the analyte can be detected efficiently down to a concentration as low as 1 × 10-8 M with an enhancement factor as high as 5.6 × 107.

Fabrication of 3D CuFe2O4/Cu0 hierarchical nanostructures on carbon fiber paper by simple hydrothermal method for efficient detection of malachite green, sunset yellow and tartrazine in food samples

In this study, a hydrothermal process was utilized to grow mixed-valence CuFe2O4/Cu0 nanosheets on carbon fiber paper, forming a three-dimensional hierarchical electrode (CuFe2O4/Cu0@CFP). The ordered array structure, coupled with the porous bowl-like structure, enhances the exposure of more electrode active sites and facilitates analyte penetration, thus enhancing the electrode sensing performance. As a binder-free sensor, the CuFe2O4/Cu0@CFP sensor exhibited remarkable sensitivity in detecting Malachite Green (MG), Sunset Yellow (SY) and Tartrazine (TA) over wide concentration ranges: 0.1-300 μM for MG (R2 = 0.994), 0.005-200 μM for SY (R2 = 0.996), and 0.005-300 μM for TA (R2 = 0.995) with low detection limits of 0.033 μM for MG, 0.0016 μM for SY, and 0.0016 μM for TA (S/N = 3), respectively. Additionally, the 3D CuFe2O4/Cu0@CFP sensor detected MG, SY, and TA in a mixed solution with satisfactory results. It also performs well in beverage, fruit juice powder, and jelly samples, with results matching those from HPLC.

Fabrication of Three-Dimensional Dendritic Ag Nanostructures: A SERS Substrate for Non-Invasive Detection

This paper discusses the fabrication of three-dimensional dendritic Ag nanostructures, showcasing pronounced Localized Surface Plasmon Resonance (LSPR) effects. These nanostructures, employed in surface-enhanced Raman scattering (SERS), function as sensors for lactic acid in artificial sweat. The dendritic structures of the silver nanoparticles (AgNPs) create an effective SERS substrate, with additional hotspots at branch junctures enhancing LSPR. We achieve differential LSPR effects by varying the distribution and spacing of branches and the overall morphology. Adjustments to electrodeposition parameters, such as current and plating solution protective agents on an anodized aluminum oxide (AAO) base, allow for precise control over LSPR intensities. By pre-depositing AgNPs, the electron transmission paths during electrodeposition are modified, which leads to optimized dendritic morphology and enhanced LSPR effects. Parameter optimization produces elongated rods with main and secondary branches, covered with uniformly sized, densely packed, non-overlapping spherical AgNPs. This configuration enhances the LSPR effect by generating additional hotspots beyond the branch tips. Fine-tuning the electrodeposition parameters improved the AgNPs' morphology, achieving uniform particle distribution and optimal spacing. Compared to non-SERS substrates, our structure amplified the Raman signal for lactic acid detection by five orders of magnitude. This method can effectively tailor SERS substrates for specific analytes and laser-based detection.

Combined Electrochemical Deposition and Photo-Reduction to Fabricate SERS-Active Silver Substrates: Characterization and Application for Malachite Green Detection in Aquaculture Water

This research introduces a novel approach using silver (Ag) nanostructures generated through electrochemical deposition and photo-reduction of Ag on fluorine-doped tin oxide glass substrates (denoted as X-Ag-AgyFTO, where 'X' and 'y' represent the type of light source and number of deposited cycles, respectively) for surface-enhanced Raman spectroscopy (SERS). This study used malachite green (MG) as a Raman probe to evaluate the enhancement factors (EFs) in SERS-active substrates under varied fabrication conditions. For the substrates produced via electrochemical deposition, we determined a Raman EF of 6.15 × 104 for the Ag2FTO substrate. In photo-reduction, the impact of reductant concentration, light source, and light exposure duration were examined on X-Ag nanoparticle formation to achieve superior Raman EFs. Under optimal conditions (9.0 mM sodium citrate, 460 nm blue-LED at 10 W for 90 min), the combination of blue-LED-reduced Ag (B-Ag) and an Ag2FTO substrate (denoted as B-Ag-Ag2FTO) exhibited the best Raman EF of 2.79 × 105. This substrate enabled MG detection within a linear range of 0.1 to 1.0 µM (R2 = 0.98) and a detection limit of 0.02 µM. Additionally, the spiked recoveries in aquaculture water samples were between 90.0% and 110.0%, with relative standard deviations between 3.9% and 6.3%, indicating the substrate's potential for fungicide detection in aquaculture.

A ratiometric fluorescent sensor based on S-doped BCNO quantum dots and Au nanoclusters combined with 3D-printing portable device for the detection of malachite green

Sulfur-doped BCNO quantum dots (S-BCNO QDs) emitting green fluorescence were prepared by elemental doping method. The ratiometric fluorescence probe with dual emissions was simply established by mixed S-BCNO QDs with gold nanoclusters (GSH-Au NCs). Because the emission spectrum of Au NCs (donor) at 615 nm overlapped well with the ultraviolet absorption of malachite green (MG), fluorescence resonance energy transfer (FRET) can be achieved. When the concentration of MG increased, the fluorescence intensity (F495) of S-BCNO QDs decreased slowly, while the fluorescence intensity (F615) of Au NCs decreased sharply. The fluorescence intensity ratio of F615/F495 decreased with the increase of MG. By plotting the F615/F495 values against MG concentration, a sensitive and rapid detection of MG was possible with a wide detection range (0.1-50 µM) and a low detection limit of 10 nM. Due to the accompanying fluorescence color change from pink to blue-green, it can be used for visual detection. A three dimensional-printing device utilizing digital image colorimetry to capture color changes through the built-in camera, enables quantitative detection of MG with a good linearity between the values of red/green ratio and MG concentrations at the range 1-50 µM. This sensing platform had a range of advantages, including high cost-effectiveness, portability, ease of operation, and high sensitivity. Furthermore, the sensing platform was successfully applied to the detection of MG in real water sample and fish samples, thereby verifying the reliability and effectiveness of this sensing platform in water quality monitoring and food safety.

Ultrasensitive Detection of Malachite Green Isothiocyanate Using Nanoporous Gold as SERS Substrate

In this article, a high-performance nanostructured substrate has been fabricated for the ultrasensitive detection of the organic pollutant, Malachite green isothiocyanate (MGITC), in aquatic systems via the Surface Enhanced Raman Spectroscopy (SERS) technique. The chemical dealloying approach has been used to synthesize a three-dimensional nanoporous gold substrate (NPG) consisting of pores and multigrained ligament structures along thickness. The formation of the framework in NPG-5h has been confirmed by SEM with an average ligament size of 65 nm at the narrower neck. Remarkable SERS performance has been achieved by utilizing the NPG-5h substrate for the detection of MGITC, showing a signal enhancement of 7.9 × 10⁹. The SERS substrate also demonstrated an impressively low-detection limit of 10^-16 M. The presence of numerous active sites, as well as plasmonic hotspots on the nanoporous surface, can be accredited to the signal amplification via the Localized Surface Plasmon Resonance (LSPR) phenomenon. As a result, SERS detection technology with the fabricated-NPG substrate not only proves to be a simple and effective approach for detecting malachite green but also provides a basis for in situ detection approach of toxic chemicals in aquatic ecosystems.

A highly sensitive surface-enhanced Raman scattering sensor with MIL-100(Fe)/Au composites for detection of malachite green in fish pond water

Concerns about food safety have been arisen due to the improper use of chemicals in aquaculture. Malachite green (MG) has attracted attention because of its illegal usage and its potential negative impacts on the environment and public health. Surface-enhanced Raman scattering (SERS) platforms coupled with different SERS substrates have been employed for rapid analysis of MG residues in food. However, the most commonly used SERS substrates were non-reusable and showed limited detection sensitivity. In this study, a novel SERS substrate with a good recyclability and a high sensitivity was prepared by electrostatically assembling together a metal-organic framework material called materials of institute lavoisie-100(Fe) (MIL-100(Fe)) and Au NPs. The lowest detectable concentration of MG was 10^-13 M based on the optimal substrate. The SERS sensor was applied for the detection of the trace MG in fish pond water, which was accomplished with the correlation coefficients R² = 0.991-0.996 in a concentration range of 10^-6-10^-13 M. Moreover, MIL-100(Fe)/Au was recycled at least five times, realizing a "detection to degradation", showing great potential for food contamination monitoring due to its distinguished performance.

Ag NP-filter paper based SERS sensor coupled with multivariate analysis for rapid identification of bacteria

Rapid and accurate identification of bacteria is essential to ensure food safety and prevent pathogenic bacterial infection. In this study, a highly efficient method was established for accurately identifying bacterial species by applying Ag NP-filter paper based Surface enhanced Raman spectroscopy (SERS) analysis and Partial Least Squares-Discriminant Analysis (PLS-DA) statistical methods. The flexible Ag NP filter paper substrate with high sensitivity and uniformity was prepared by a facile and low-cost silver mirror reaction at room temperature, which exhibited desirable SERS activity in bacteria detection. Furthermore, PLS-DA was successfully employed to distinguish SERS spectra from S. aureus CMCC 26003, E. faecalis ATCC29212 and L. monocytogenes ATCC 19115 with a sensitivity of 93.3-100%, specificity of 96.7-97%, and overall predicting accuracy of 95.8%. This exploratory study demonstrates that a Ag NP-filter paper based SERS sensor coupled with PLS-DA has great potential for rapid and effective detection and identification of bacteria.

Dual-reverse-signal ratiometric fluorescence method for malachite green detection based on multi-mechanism synergistic effect

The proposition of ratiometric detection mode has demonstrated great superiority in improving analysis accuracy by forming self-calibration. Herein, the novel dual-reverse-signal ratiometric fluorescence detection for malachite green (MG) was first achieved based on synergistic effect of fluorescence resonance energy transfer (FRET) and inner filter effect (IFE). The ratiometric fluorescence probe (B-RCDs) was self-assembled via electrostatic attraction between blue-emission carbon dots (BCDs) and red-emission carbon dots (RCDs), followed with FRET effect from BCDs to RCDs and exhibited dual-emission at 450 nm and 627 nm. In the presence of MG, the IFE effect between MG and RCDs quenched the fluorescence at 627 nm and restored the fluorescence at 450 nm, sending out two reverse signals along with an obvious color change from pink to purple (302 nm UV lamp). This ratiometric method not only simplified the preparation process, but also improved the detection sensitivity, showing a low limit of detection (LOD) of 41.8 nM, which exhibited superiority than that of single-signal RCDs (157.3 nM). This method held a rapid response of 10 min and represented satisfactory recoveries (99.14%-109.08%) in real water samples, revealing it was a promising candidate in the fast, sensitive and practical detection of MG. Moreover, the design of synergistic effect supplied a new perspective for the development of ratiometric sensing in the future.

Simple synthesis of green luminescent N-doped carbon dots for malachite green determination

In this paper, novel N-doped carbon dots (N-CDs) were prepared from fuchsin basic and ethylenediamine tetraacetic acid-disodium salt (EDTA-2Na). The N-CDs were characterized by a series of techniques and it was found that the average particle size was 2.75 nm, and the surface had functional groups such as -NH₂ and -COOH. Interestingly, N-CDs exhibited a fast and sensitive response to malachite green (MG), which may be due to the inner filter effect (IFE). A method for the detection of MG in water samples from Jinyang Lake was developed using N-CDs, with a limit of detection (LOD) as low as 27.28 nM. Furthermore, N-CDs were utilized in the biological imaging of Arabidopsis thaliana.

Optimum synthesis of cactus-inspired SERS substrate with high roughness for paraquat detection

Paraquat is a highly effective herbicide and widely used in agricultural production. However, paraquat residue is harmful for human health and can cause irreversible hazard. Thus, it is crucial for monitoring of paraquat residues. In this paper, an efficient SERS platform based on cactus-inspired nanoparticles is proposed for sensitive detection of paraquat. The cactus-liked nanoparticles obtained from one-pot stepwise reduction method possess multiple spiny structures and can produce abundant hot spots, resulting in remarkable SERS performance. SEM, TEM, UV-vis and Raman tests were conducted to characterize and optimize the morphology of cactus-liked nanoparticles under different preparation conditions. The synthesis mechanism and corresponding parameters influence mechanism of cactus-liked nanoparticles were explored in detail. Optimized substrate exhibited a high sensitivity with the detectable concentration of crystal violet (CV) down to 10^-9 M and an excellent reproducibility proved by SERS mapping. Furthermore, it behaved good linear relationship with a correlation coefficient (R²) of 96.89% between Raman intensities and concentrations of paraquat, which indicates the SERS substrate prepared with cactus-liked nanoparticles could offer a great potential for identification of paraquat.

Size controlled silver nanoparticles on β-cyclodextrin/graphitic carbon nitride: an excellent nanohybrid material for SERS and catalytic applications

A nanohybrid (NH), having high dispersion of silver nanoparticles (AgNPs) on β-cyclodextrin (β-CD)/graphitic carbon nitride (g-CN), designated as AgNPs/β-CD/g-CN-NH, was synthesized and characterized. It was exploited for a couple of environmental remediation applications like SERS sensing and catalytic reduction of specific organic pollutants in water. It showed excellent SERS activity as a Raman probe for the detection of malachite green (MG). Its enhancement factor (EF) and detection limit for MG were equal to 7.26 × 10⁶ and 1 × 10^-9 M, respectively. The relative standard deviation (RSD) was equal to 3.8% which indicates high homogeneity of AgNP dispersion and signal reproducibility of the SERS substrate. The NH displayed high catalytic activity for the reduction of eosin yellow (EY) in the presence of NaBH₄ with the rate constant (k) of 0.1142 min^-1. A comparison of the present NH with other reported materials reveals better SERS and catalytic activities of the former than those of the latter. The SERS activity of the NH was also examined for sensing of other triphenylamine dyes like methyl violet (MV), and it was successful. The same NH also exhibited high catalytic activity towards the reduction of Congo red (CR). The results of both studies clarify that the NH is an excellent SERS substrate and efficient catalyst for the detection of organic environmental pollutants having structures similar to MG and their degradation. This is due to the distribution of the controlled size of AgNPs on g-CN promoted by β-CD. Therefore, we focus our attention on future environmental applications of the nanohybrid as a very cheap SERS substrate and a very active catalyst.

Flower-like Ag coated with molecularly imprinted polymers as a surface-enhanced Raman scattering substrate for the sensitive and selective detection of glibenclamide

Flower-like Ag was formed by nanosheet self-assembly as a SERS-active substrate and was utilized for the preparation of flower-like Ag@molecularly imprinted polymers (MIPs) as a surface-enhanced Raman scattering (SERS) sensor. Based on the combination of the molecular imprinting technique and SERS technology, the flower-like Ag@MIPs with high sensitivity and excellent selectivity were used as SERS substrates for the detection of glibenclamide. The imprinted layer could effectively protect the flower-like Ag from oxidation and thereby may improve the stability of the SERS substrate. The intensities of the characteristic peaks obtained for the flower-like Ag@MIPs were higher than that of flower-like Ag. By applying the flower-like Ag@MIPs as an efficient and ultra-sensitive SERS platform, glibenclamide was quantitatively detected in trace concentrations as low as 1 ng mL-1. Furthermore, the SERS enhancement for the flower-like Ag@MIPs was due to the synergetic effect between electromagnetic enhancement and chemical enhancement. We believe that this reliable method can open up new opportunities for practical chemosensor or biosensor applications.