The electrochemical behaviors and kinetics of AuNPs/N, S-GQDs composite electrode: A novel label-free amplified BPA aptasensor with extreme sensitivity and selectivity

Flexible genosensors based on polypyrrole and graphene quantum dots for PML/RARα fusion gene detection: A study of acute promyelocytic leukemia in children

Acute promyelocytic leukemia (APL) in children is associated with a favorable initial prognosis. However, minimal residual disease (MRD) follow-up remains poorly defined, and relapse cases are concerning due to their recurrent nature. Thus, we report two electrochemical flexible genosensors based on polypyrrole (PPy) and graphene quantum dots (GQDs) for label-free PML-RARα oncogene detection. Atomic force microscopy (AFM), scanning electron microscope (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) were used to characterize the technological biosensor development. M7 and APLB oligonucleotide sequences were used as bioreceptors to detect oncogenic segments on chromosomes 15 and 17, respectively. AFM characterization revealed heterogeneous topographical surfaces with maximum height peaks for sensor layers when tested with positive patient samples. APLB/Genosensor exhibited a percentage change in anode peak current (ΔI) of 423 %. M7/Genosensor exhibited a ΔI of 61.44 % for more concentrated cDNA samples. The described behavior is associated with the biospecific recognition of the proposed biosensors. Limits of detection (LOD) of 0.214 pM and 0.677 pM were obtained for APLB/Genosensor and M7/Genosensor, respectively. The limits of quantification (LOQ) of 0.648 pM and 2.05 pM were estimated for APLB/Genosensor and M7/Genosensor, respectively. The genosensors showed reproducibility with a relative standard deviation of 7.12 % for APLB and 1.18 % for M7 and high repeatability (9.89 % for APLB and 1.51 % for M7). In addition, genetic tools could identify the PML-RARα oncogene in purified samples, plasmids, and clinical specimens from pediatric patients diagnosed with APL with high bioanalytical performance. Therefore, biosensors represent a valuable alternative for the clinical diagnosis of APL and monitoring of MRD with an impact on public health.

Simultaneous electrochemical detection of dimethyl bisphenol A and bisphenol A using a novel Pt@SWCNTs-MXene-rGO modified screen-printed sensor

Since bisphenol A (BPA) and dimethyl bisphenol A (DM-BPA) are human endocrine disruptors (EDCs) with tiny potential differences (44 mV) and widespread applications, there is a lack of published reports on their simultaneous detection. Therefore, this study reports a novel electrochemical detection system capable of simultaneous direct detection of BPA and DM-BPA using screen-printed carbon electrodes (SPCE) as a sensing platform. To improve the electrochemical performance of the SPCE, the SPCE was modified by using a combination of Pt nanoparticles modified with single-walled carbon nanotubes (Pt@SWCNTs), MXene (Ti₃C₂), and graphene oxide (GO). In addition, the GO in Pt@SWCNTs-MXene-GO was reduced to reduced graphene oxide (rGO) by the action of electric field (-1.2 V), which significantly improved the electrochemical properties of the composites and effectively solved the problem of dispersion of the modified materials on the electrode surface. Under optimal experimental conditions, Pt@SWCNTs-Ti₃C₂-rGO/SPCE exhibited a suitable detection range (0.006-7.4 μmol L^-1) and low detection limits (2.8 and 3 nmol L^-1, S/N = 3) for the simultaneous detection of BPA (0.392 V vs. Ag/AgCl) and DM-BPA (0.436 V vs. Ag/AgCl)). Thus, this study provides new insights into detecting compounds with similar structures and slight potential differences. Finally, the developed sensor's reproducibility, stability, interference resistance and accuracy were demonstrated with satisfactory results.

Advancements in nanomaterial-based aptasensors for the detection of emerging organic pollutants in environmental and biological samples

The combination of nanomaterials (NMs) and aptamers into aptasensors enables highly specific and sensitive detection of diverse pollutants. The great potential of aptasensors is recognized for the detection of diverse emerging organic pollutants (EOPs) in different environmental and biological matrices. In addition to high sensitivity and selectivity, NM-based aptasensors have many other advantages such as portability, miniaturization, facile use, and affordability. This work showcases the recent advances achieved in the design and fabrication of NM-based aptasensors for monitoring EOPs (e.g., hormones, phenolic contaminants, pesticides, and pharmaceuticals). On the basis of their sensing mechanisms, the covered aptasensing systems are classified as electrochemical, colorimetric, PEC, fluorescence, SERS, and ECL. Special attention has been paid to the fabrication processes, analytical achievements, and sensing mechanisms of NM-based aptasensors. Further, the practical utility of aptasensing approaches has also been assessed based on their basic performance metrics (e.g., detection limits, sensing ranges, and response times).

Modern Electrochemical Biosensing Based on Nucleic Acids and Carbon Nanomaterials

To meet the requirements of novel therapies, effective treatments should be supported by diagnostic tools characterized by appropriate analytical and working parameters. These are, in particular, fast and reliable responses that are proportional to analyte concentration, with low detection limits, high selectivity, cost-efficient construction, and portability, allowing for the development of point-of-care devices. Biosensors using nucleic acids as receptors has turned out to be an effective approach for meeting the abovementioned requirements. Careful design of the receptor layers will allow them to obtain DNA biosensors that are dedicated to almost any analyte, including ions, low and high molecular weight compounds, nucleic acids, proteins, and even whole cells. The impulse for the application of carbon nanomaterials in electrochemical DNA biosensors is rooted in the possibility to further influence their analytical parameters and adjust them to the chosen analysis. Such nanomaterials enable the lowering of the detection limit, the extension of the biosensor linear response, or the increase in selectivity. This is possible thanks to their high conductivity, large surface-to-area ratio, ease of chemical modification, and introduction of other nanomaterials, such as nanoparticles, into the carbon structures. This review discusses the recent advances on the design and application of carbon nanomaterials in electrochemical DNA biosensors that are dedicated especially to modern medical diagnostics.

Determination of trace amount of iron cations using electrochemical methods at N, S doped GQD modified electrode

In this work, nitrogen and sulfur co-doped graphene quantum dot-modified glassy carbon electrodes (N, S-GQD/GCE) were used for the recognition of iron cations in aqueous solutions. The dissolved cations are detected based on the faradaic reduction or oxidation current of Fe(III) and Fe(II) obtained at the N, S-GQD/GCE surface. Cyclic voltammetry (CV), square wave voltammetry (SWV), and hydrodynamic amperometry are used as suitable electrochemical techniques for studying electrochemical behavior and determination of Fe cations. Based on the obtained results, it is concluded that the presence of free electrons in the structure of N, S-GQD could facilitate electron transfer reaction between Fe(III) and electrode surface which with increased surface area results in increased sensitivity and lower limit of detection. By performing suitable experiments, the best condition for preparing the modified electrode and determining Fe(III) was selected. Under optimized conditions, the amperometric response is linear from 1 to 100 nM of Fe(III) with a detection limit of 0.23 nM. The validity of the method and applicability of the sensor is successfully tested by the determination of Fe(III) in drug and water real samples. This sensor opened a new platform based on doped nanoparticles for highly sensitive and selective detection of analytes.

Photoelectrochemical biosensor based on DNA aptamers and dual nano-semiconductor heterojunctions for accurate and selective sensing of chloramphenicol

Nanosheets of anatase TiO₂ and CdS quantum dots modified with thioglycolic acid (TGA-CdS QDs) were prepared and hierarchically modified on the indium tin oxides (ITO) electrodes. The heterojunction structure is formed to improve the light capture ability and carrier migration, significantly enhancing the sensitivity of photoelectrochemical (PEC) biosensors. Specific DNA sequences labeled with TGA-CdS QDs were placed on the electrodes to prepare a biosensor for the detection of chloramphenicol with ultrahigh selectivity. In addition, the heterojunction structure and the principle of photocurrent signal amplification on the electrode are described in detail. Under the optimal conditions, the photoelectrochemical biosensors showed good reproducibility and stability for chloramphenicol with a linear response in the range 10-10,000 pM and a limit of detection (LOD) of 0.23 pM. Due to the specific recognition of base pairs, the sensor has excellent anti-interference ability in practical applications. An effective method was developed for the accurate detection of antibiotics with far reaching prospects.

A paper-analytical device for detecting bisphenol-A in foods

Bisphenol A (BPA) is a plastic monomer that can leach into food and cause adverse health effects with long-term exposure. In this study, we developed simple paper-analytical devices (PADs) for detecting BPA in food. The PADs were designed with hydrophilic and hydrophobic areas via wax printing. The hydrophilic areas were designed as a detection zone and modified with carboxymethyl cellulose (CMC) for the immobilisation of BPA-bovine serum albumin (BSA). The monoclonal antibodies against BPA were generated and modified with quantum dots (QDs) to synthesise QD-antibody (QD-Ab) probes. Detection conditions of the assay were optimized, with results of 0.1 μg of BPA-BSA and 30-fold diluted QD-Ab probes. The detection limit was 0.098 μg L^-1 using ImageJ analysis. Samples of drinking water, green tea beverage and peanut cooking oil were selected to conduct the matrix effect study. The recovery rates of BPA in different samples ranged from 78.77% to 118.96%, proving that the PADs were a simple and sensitive detection method for easy, low-cost analysis of real food samples.

Direct and Sensitive Electrochemical Detection of Bisphenol A in Complex Environmental Samples Using a Simple and Convenient Nanochannel-Modified Electrode

Rapid, convenient, and sensitive detection of Bisphenol A (BPA) in complex environmental samples without the need for tedious pre-treatment is crucial for assessing potential health risks. Herein, we present an electrochemical sensing platform using a simple nanochannel-modified electrode, which enables the direct and sensitive detection of BPA in complex samples. A vertically ordered mesoporous silica-nanochannel film (VMSF) with high-density nanochannels is rapidly and stably grown on the surface of a electrochemically activated glassy carbon electrode (p-GCE) by using the electrochemically assisted self-assembly (EASA) method. The high antifouling capability of the VMSF/p-GCE sensor is proven by investigating the electrochemical behavior of BPA in the presence of model coexisting interfering molecules including amylum, protein, surfactant, and humic acid. The VMSF/p-GCE sensor can sensitively detect BPA ranged from 50 to 1.0 μM and 1.0–10.0 μM, with low detection limits (15 nM). Owing to the electrocatalytic performance and high potential resolution of p-GCE, the sensor exhibits high selectivity for BPA detection in the presence of common environmental pollutants, including bisphenol S (BPS), catechol (CC), hydroquinone (HQ), and 4-nitrophenol (4-NP). In combination with the good antifouling property of the VMSF, direct detection of BPA in environmental water samples and soil leaching solution (SLS) is also realized without separation pretreatment. The developed VMSF/p-GCE sensor demonstrated advantages of simple structure, high sensitivity, good antifouling performance, and great potential in direct electroanalysis of endocrine-disrupting compounds in complex samples.

Active site regulated Z-scheme MIL-101(Fe)/Bi2WO6/Fe(III) with the synergy of hydrogen peroxide and visible-light-driven photo-Fenton degradation of organic contaminants

Water pollution control is one of the major challenges currently faced. With the development of photocatalytic technology, an increasing number of new and efficient catalysts have been developed, but most of the catalysts have limited light capture ability and catalytic degradation efficiency. Therefore, in this work, hydrogen peroxide was further introduced to establish a photo-Fenton system to improve the photocatalytic effect by constructing a Z-scheme, and the degradation ability of the catalyst was maximized. Moreover, we successfully adhered bismuth tungstate nanosheets onto the surface of a MIL-101(Fe) framework and changed the number of active sites with iron ions of different doping amounts. We found that the number of active sites in the photo-Fenton system does not increase linearly, but increases and decreases regularly, which is similar to the change in band structure after doping. In addition, the results of the radical scavenger experiment and electron paramagnetic resonance (EPR) revealed that both hydroxide radical (˙OH) and superoxide radical (˙O₂^-) participated in methylene blue (MB) degradation, of which ˙OH was the main active species for pollutant degradation. Based on high-performance liquid chromatography-mass spectrometry (HPLC-MS) analysis, the possible degradation pathways were proposed. We believed that this work will provide insights into the heterojunction photo-Fenton system.

Measurement of trace bisphenol A in drinking water with combination of immunochromatographic detection technology and SERS method

Sensitive and selective detection of target analyte is very important in many fields such as commodity inspection and quality monitoring. In this work, based on the principle of competitive immunoassay, surface-enhanced Raman spectroscopy (SERS) was used to establish a rapid and highly sensitive method for the detection of trace amounts of bisphenol A in water. Here, Raman molecule 5,5-dithiobis-2-nitrobenzoic acid and anti-BPA antibody were conjugated with Au (core)@Ag (shell) nanoparticle to serve as SERS nanoprobe. After the SERS nanoprobe is combined with the substance to be tested, it uses the siphon effect to pass through the test line and the charging line on the test strip. And the Raman test was performed on the T line with a Raman spectrometer. The detection limitation was 0.1 pg/mL. Compared with the reported gas chromatography, liquid chromatography, fluorescence analysis, and other detection methods, SERS ICA does not demand complicated sample preparation procedures, and has the advantages of simple detection methods, quick results, High sensitivity, good specificity, and low technical demands for laboratory environment and testers. In addition, Raman spectrometers have gradually developed to be portable, making it easier to meet the needs of on-site rapid and highly sensitive detection, and will show broad prospects for applications in the fields of biomedical diagnosis and food safety monitoring.

Design and Analysis of a Single System of Impedimetric Biosensors for the Detection of Mosquito-Borne Viruses

The treatment for mosquito-borne viral diseases such as dengue virus (DENV), zika virus (ZIKV), and chikungunya virus (CHIKV) has become difficult due to delayed diagnosis processes. In addition, sharing the same transmission media and similar symptoms at the early stage of infection of these diseases has become more critical for early diagnosis. To overcome this, a common platform that can identify the virus with high sensitivity and selectivity, even for the different serotypes, is in high demand. In this study, we have attempted an electrochemical impedimetric method to detect the ZIKV, DENV, and CHIKV using their corresponding antibody-conjugated sensor electrodes. The significance of this method is emphasized on the fabrication of a common matrix of gold-polyaniline and sulfur, nitrogen-doped graphene quantum dot nanocomposites (Au-PAni-N,S-GQDs), which have a strong impedimetric response based only on the conjugated antibody, resulting in minimum cross-reactivity for the detection of various mosquito-borne viruses, separately. As a result, four serotypes of DENV and ZIKV, and CHIKV have been detected successfully with an LOD of femtogram mL-1.

Graphene Quantum Dots-Based Nanocomposites Applied in Electrochemical Sensors: A Recent Survey

Graphene quantum dots (GQDs) have been widely investigated in recent years due to their outstanding physicochemical properties. Their remarkable characteristics allied to their capability of being easily synthesized and combined with other materials have allowed their use as electrochemical sensing platforms. In this work, we survey recent applications of GQDs-based nanocomposites in electrochemical sensors and biosensors. Firstly, the main characteristics and synthesis methods of GQDs are addressed. Next, the strategies generally used to obtain the GQDs nanocomposites are discussed. Emphasis is given on the applications of GQDs combined with distinct 0D, 1D, 2D nanomaterials, metal-organic frameworks (MOFs), molecularly imprinted polymers (MIPs), ionic liquids, as well as other types of materials, in varied electrochemical sensors and biosensors for detecting analytes of environmental, medical, and agricultural interest. We also discuss the current trends and challenges towards real applications of GQDs in electrochemical sensors.

The Role of Aryldiazonium Chemistry in Designing Electrochemical Aptasensors for the Detection of Food Contaminants

Food safety monitoring assays based on synthetic recognition structures such as aptamers are receiving considerable attention due to their remarkable advantages in terms of their ability to bind to a wide range of target analytes, strong binding affinity, facile manufacturing, and cost-effectiveness. Although aptasensors for food monitoring are still in the development stage, the use of an electrochemical detection route, combined with the wide range of materials available as transducers and the proper immobilization strategy of the aptamer at the transducer surface, can lead to powerful analytical tools. In such a context, employing aryldiazonium salts for the surface derivatization of transducer electrodes serves as a simple, versatile and robust strategy to fine-tune the interface properties and to facilitate the convenient anchoring and stability of the aptamer. By summarizing the most important results disclosed in the last years, this article provides a comprehensive review that emphasizes the contribution of aryldiazonium chemistry in developing electrochemical aptasensors for food safety monitoring.

Graphene quantum dots as nanosensor for rapid and label-free dual detection of Cu2+ and tiopronin by means of fluorescence “on–off–on” switching: mechanism and molecular logic gate

(A) Schematic diagram of the interaction and dual detection of Cu2+ and MPG by means of fluorescence “on–off–on” switching. (B) Molecular logic gate and truth table constructed based on Cu2+ and MPG as inputs and emission signal as output.