Preparation and characterization of ionic and non-ionic surfactants impregnated κ-carrageenan hydrogel beads for investigation of the adsorptive mechanism of cationic dye to develop for biomedical applications

Construction and characterization of sodium alginate/polyvinyl alcohol double-network hydrogel beads with surfactant-tailored adsorption capabilities for efficient tetracycline hydrochloride removal

The extensive use of tetracycline (TC) for disease control and the residuals in wastewater has resulted in the spread and accumulation of antibiotic resistance genes, posing a severe threat to the human health and environmental safety. To solve this problem, a series of double-network hydrogel beads based on sodium alginate and polyvinyl alcohol were constructed with the introduction of various surfactants to modulate the morphology. The results showed that the introduction of surfactants can modulate the surface morphology and internal structure, which can also regulate the adsorption ability of the hydrogel beads. The SDS-B beads with SDS as surfactant exhibited highest adsorption efficiency for removal of TC with a maximum adsorption capacity up to 121.6 mg/g, which possessed a resistance to various cations and humic acid. The adsorption mechanism revealed that the superior adsorption performance of the hydrogel beads was primarily attributed to hydrogen bonding, electrostatic attraction, and π-π EDA interactions. Adsorption kinetics demonstrated that the pseudo-second-order model fitted the adsorption process well and adsorption isotherm showed the adsorption of TC occurred through both chemical and physical interactions. Moreover, the adsorption efficiency remained approximately 87.5 % after three adsorption-desorption cycles, which may have potential application and practical value in TC adsorption.

Functionalization of MXene using iota-carrageenan, maleic anhydride, and N,N'-methylene bis-acrylamide for high-performance removal of thorium (IV), uranium (IV), sulfamethoxazole, and levofloxacin

An increasing quantity of pollutants has been discharged into the aquatic media, posing a serious hazard to public health. To address this issue, a new sorbent material, MXene@i.Carr@MaMb, was developed through the functionalization of the MXene surface using iota-carrageenan (i.Carr), maleic anhydride, and N, N'-methylene bis-acrylamide. This sorbent material was designed to remove thorium (Th (IV)) effectively, uranium (U (IV)), sulfamethoxazole (SMX), and levofloxacin (LEV) from wastewater. The MXene@i.Carr@MaMb composite incorporated significant functional groups, including OH, F, and O from MXene, oxygen and ester sulfate groups from iota-carrageenan (i.Carr), and OH, NH, and CO groups from N, N'-methylene bis-acrylamide, and maleic anhydride, which interacted with the UV (IV), Th (IV), SMX, and LEV pollutants through electrostatic interaction, complexation, and hydrogen bonding. MXene@i.Carr@MaMb composite exhibited excellent sorption capacities for Th (IV) (3.6 ± 0.03 mmol g-1), U (IV) (3.7 ± 0.09 mmol g-1), SMX (5.8 ± 0.03 mmol g-1), and LEV (5.9 ± 0.05 mmol g-1) at 323.15 K. The sorption kinetics and isotherms of radioactive metals and antibiotics can be well-described using pseudo-first-order kinetic models and Langmuir and Sips isothermal equations. This study presented a novel sorbent material for efficiently removing radioactive metals and antibiotics from wastewater.

Synergy of Magnetic Nanoparticles and Sodium Alginate-Coated Lignin for Effective Pollutant Remediation, Simple Recovery, and Cost-Effective Regeneration

In the pursuit of sustainable materials for environmental remediation, this study presents the development and comprehensive characterization of cobalt ferrite nanoparticles (CFNPs) incorporated in lignocellulosic-derived sodium alginate (CFNPs@LCG-SA) biocomposite beads. These biobased beads exhibit exceptional adsorption capabilities, particularly for methylene blue (MB) dyes, rendering them promising candidates for wastewater treatment. Using a comprehensive range of analytical techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis-derivative thermogravimetry (TGA/DTG), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), etc., we elucidated their structural, physicochemical, and thermal properties. Their multifunctional nature, derived from lignin and sodium alginate components, provides ample active sites for both physical interactions and chemical bonding with contaminants apart from the magnetic character attributed by the CFNPs. With a freeze-drying approach, the optimal adsorption capacity and removal rate of MB reached 97 mg/g and 99%, respectively, and no meaningful decline in their activity was noted even after six cycles. The CFNPs@LCG-SA biocomposite beads emerge as a cost-efficient and sustainable remedy for environmental cleanup, offering valuable perspectives in environmental preservation and advancing green energy technologies.

Efficient oil spill cleanup from water: Investigating the effectiveness of a sustainable anti-swelling hydrogel for rapid water repellency and oil absorption

Considering the significant harm caused to aquatic ecosystems and marine life by oil spills and the discharge of oily wastewater, there is a pressing need to address this issue to protect our environment and prevent the wastage of valuable resources. We introduced a two-step approach to create an anti-swelling, water-repellent sorbent using a green polysaccharide called gum gellan, functionalized with Octadecyl trichlorosilane (OTS) through dip coating method. Natural gums like gellan have high absorption capability due to their large surface area. However, they are hydrophilic, which means they can only absorb water. This property makes them unsuitable for oil spill applications. To make gum gellan suitable for oil spill applications, we have modified it in this study. We have introduced a material called octadecyltrichlorosilane, which has low surface energy and hierarchical roughness. This modification changes the wettability of gellan from hydrophilic to hydrophobic/oleophilic, allowing it to absorb oil and repel water. The sorbent is analyzed using several techniques, such as FTIR, XRD, TGA, FE-SEM, BET, Raman, EDX, and H1-NMR. The hydrophobic sorbent obtained demonstrates low density, high surface area, and high porosity. These characteristics give it excellent floatability and immediate and exceptional selectivity for absorbing oil from water. Additionally, it does not absorb any detectable amount of water. The sorbent exhibited a water contact angle (WCA) of 140 ± 3 ° and an oil contact angle (OCA) of 0° for various oils and organic solvents. It has rapid oil absorption capacity of 3.72 g/g for diesel, and can be easily recovered after use. The BET analysis revealed that after the modification with OTS, the sorbent's total surface area increased from 0.579 m2/g to 4.713 m2/g. This indicates that the OTS modification greatly enhances the surface area and pore volume of the, thus improving its ability to absorb oil. This sorbent efficiently separates oil-in-water emulsions, both surfactant-stabilized and surfactant-free, achieving over 90% separation through gravity alone. Moreover, the sorbent can sustain its wettability even under harsh environmental conditions, including exposure to acids, alkalis, and salts. The absorption data predominantly aligned with the pseudo-2nd-order model. Thus, this sorbent provides a cost-effective alternative for efficiently absorbing and separating oil-water emulsions in households and industries.

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Preparation of iota-carrageenan@bentonite@4-phenyl-3-thiosemicarbazide ternary hydrogel for adsorption of Losartan potassium and sulfamethoxazole

A rising quantity of drugs has been discharged into the aquatic environment, posing a substantial hazard to public health. In the current work, a novel hydrogel (i.Carr@Bent@PTC), comprised of iota-carrageenan, bentonite, and 4-phenyl-3-thiosemicarbazide, was successfully prepared. The introduction of 4-phenyl-3-thiosemicarbazide and bentonite in iota-carrageenan significantly increased the mechanical strength of iota-carrageenan hydrogel and improved its degree of swelling, which can be attributed to the hydrophilic properties of PTC and Bent. The recorded contact angle was 70.8°, 59.1°, 53.9°, and 34.6° for pristine i.Carr, i.Carr@Bent, and i.Carr@Bent@PTC, respectively. The low contact angle measurement of the Bent and PTC loaded-i.Carr hydrogel was attributed to the hydrophilic Bent and PTC. The ternary i.Carr@Bent@PTC hydrogel demonstrated broad pH adaptability and excellent adsorption capacities for sulfamethoxazole (SMX) and losartan potassium (LP), i.e., 467.61 mg. g-1 and 274.43 mg. g-1 at 298.15 K, respectively. The pseudo-first-order (PSO) model provided a better fit for the adsorption kinetics. The adsorption of SMX and LP can be better explained by employing the Sips and Langmuir isotherm models. As revealed by XPS and FTIR investigations, π-π stacking, complexation, electrostatic interaction, and hydrogen bonding were primarily involved in the adsorption mechanisms.

Comparative Analysis of Hydrogel Adsorption/Desorption with and without Surfactants

In this particular study, a hydrogel known as SAP-1 was synthesized through the grafting of acrylic acid-co-acrylamide onto pullulan, resulting in the creation of Pul-g-Poly (acrylic acid-co-acrylamide). Additionally, a sponge hydrogel named SAP-2 was prepared by incorporating the surfactant sodium dodecyl benzene sulfonate (SDBS) into the hydrogel through free radical solution polymerization. To gain further insight into the composition and properties of the hydrogels, various techniques, such as Fourier transform infrared spectroscopy, hydrogen nuclear magnetic resonance (1H NMR), atomic absorption spectroscopy, and field emission scanning electron microscopy (FE-SEM), were employed. Conversely, the absorption kinetics and the equilibrium capacities of the prepared hydrogels were investigated and analyzed. The outcomes of the investigation indicated that each of the synthesized hydrogels exhibited considerable efficacy as adsorbents for cadmium (II), copper (II), and nickel (II) ions. In particular, SAP-2 gel displayed a remarkable cadmium (II) ion absorption ability, with a rate of 190.72 mg/g. Following closely, SAP-1 gel demonstrated the ability to absorb cadmium (II) ions at a rate of 146.9 mg/g and copper (II) ions at a rate of 154 mg/g. Notably, SAP-2 hydrogel demonstrated the ability to repeat the adsorption-desorption cycles three times for cadmium (II) ions, resulting in absorption capacities of 190.72 mg/g, 100.43 mg/g, and 19.64 mg/g for the first, second, and third cycles, respectively. Thus, based on the abovementioned results, it can be concluded that all the synthesized hydrogels possess promising potential as suitable candidates for the adsorption and desorption of cadmium (II), copper (II), and nickel (II) ions.

Graphene oxide@Fe3O4-decorated iota-carrageenan composite for ultra-fast and highly efficient adsorption of lead (II) from water

The aggravated problem of lead pollution, especially in aquatic environments, necessitates the development of eminent adsorbents that could radically solve this environmental problem. Hence, a new composite was constructed based on iota carrageenan (i.Carr), graphene oxide (GO) and magnetite (Fe3O4) for removing noxious Pb2+ ions. The GO@Fe3O4-i.Carr composite was characterized by VSM, SEM, XPS, XRD, FTIR and Zeta potential. The removal of Pb2+ ions attained a quick equilibrium of almost 30 min with a removal efficiency reaching 93.68 %. The removal of Pb2+ was boosted significantly, in the order of GO@Fe3O4-i.Carr(1:1) > GO@Fe3O4-i.Carr(1:3) > GO@Fe3O4-i.Carr(3:1). Moreover, acquired experimental data fitted the pseudo 2nd order kinetic model and Freundlich isotherm model with a maximal monolayer adsorption capacity reached 440.05 mg/g. Notably, after five adsorption runs, the composite maintained its removal efficiency exceeding 74 %. The assumed adsorption mechanisms of Pb2+ onto GO@Fe3O4-i.Carr were complexation, precipitation, Lewis acid-base, and electrostatic attraction forces. Overall, the GO@Fe3O4-i.Carr composite elucidated the auspicious adsorbent criteria, comprising fast adsorption with high performance, ease-separation and tolerable recyclability, advising its feasible use to decontaminate water bodies from hazardous heavy metals.

A magnetically recyclable carboxyl-functionalized chitosan composite for efficiently removing methyl orange from wastewater: Isotherm, kinetics, thermodynamic, and adsorption mechanism

In this study, a kind of magnetically recyclable adsorbent for dyes was synthesized by grafting diethylenetriamine pentaacetate acid (DTPA) to the composite of Fe3O4 microspheres and crosslinked chitosan (CS). The microstructures, molecular structure, crystal structure, and magnetic hysteresis loops of the chitosan matrix adsorbent before and after grafting was characterized. The results suggested that DTPA was covalent bonded with the composite of Fe3O4 microspheres and chitosan. The modified composite has larger specific surface area and can realize rapid solid-liquid separation. Batch experiments were conducted to optimize the parameters affecting the adsorption of methyl orange (MO). The adsorption process could be better described by pseudo-second-order kinetics model and Langmuir isotherm equation, and its saturated adsorption capacity of the modified adsorbents was 1541.5 mg·g-1 at 25 °C, which was 1.40 times of that the unmodified adsorbent (1104.1 mg·g-1). The obtained values of the thermodynamic parameters indicated that the adsorption was a spontaneous process. The regeneration experiment proved the stability and reproducibility of the adsorbent even after five cycles of adsorption-desorption. The primary adsorption mechanism was electrostatic interaction and hydrogen bonding. The adsorbent could be potentially applied for removing dyes from wastewater in wide pH of range, especially acid wastewater.

High adsorption performance for trace lead (II) cation from sewage by Fe/Cu metal organic nanosheets modified with terephthalic acid

A two-dimensional nanoflake (Fe/Cu-TPA) was prepared through a simple ultrasonic-centrifuge method. Fe/Cu-TPA has prominent performance on the removal of Pb²⁺ with low consistences. More than 99% lead (II) (Pb²⁺) was removed. The adsorption equipoise was established within 60 min for 50 mg L^-1 Pb²⁺. Fe/Cu-TPA shows excellent regenerability with 19.04% decline of Pb²⁺ adsorption competence in 5 cycles. There are two models for Fe/Cu-TPA adsorption of Pb²⁺, pseudo-second-order dynamic model and Langmuir isotherm model, with a utmost adsorption competence of 213.56 mg g^-1. This work offers a new candidate material for the industrial-grade Pb²⁺ adsorbents with promising application prospect.

Design of separable magnetic chitosan grafted-benzaldehyde for azo dye removal via a response surface methodology: Characterization and adsorption mechanism

In this study, a magnetic chitosan grafted-benzaldehyde (CS-BD/Fe₃O₄) was hydrothermally prepared using benzaldehyde as a grafting agent to produce a promising adsorbent for the removal of acid red 88 (AR88) dye. The CS-BD/Fe₃O₄ was characterized by infrared spectroscopy, surface area analysis, scanning electron microscopy-energy dispersive X-ray, vibrating sample magnetometry, powder X-ray diffraction, CHN elemental analysis, and point of zero charge (pH_PZC). The Box-Behnken design (BBD) was adopted to study the role of variables that influence AR88 dye adsorption (A: CS-BD/Fe₃O₄ dose (0.02-0.1 g), B: pH (4-10), and time C: (10-90 min)). The ANOVA results of the BBD model indicated that the F-value for the AR88 removal was 22.19 %, with the corresponding p-value of 0.0002. The adsorption profiles at equilibrium and dynamic conditions reveal that the Temkin model and the pseudo-first-order kinetics model provide an adequate description of the isotherm results, where the maximum adsorption capacity (qmax) with the AR88 dye was 154.1 mg/g. Several mechanisms, including electrostatic attraction, n-π interaction, π-π interaction, and hydrogen bonding, regulate the adsorption of AR88 dyes onto CS-BD/Fe₃O₄ surface. As a result, this research indicates that the CS-BD/Fe₃O₄ can be utilized as an effective and promising bio-adsorbent for azo dye removal from contaminated wastewater.

Insight into the adsorptive removal of ibuprofen using porous carbonaceous materials: A review

Over the last decade, the removal of pharmaceuticals from aquatic bodies has garnered substantial attention from the scientific community. Ibuprofen (IBP), a non-steroidal anti-inflammatory drug, is released into the environment in pharmaceutical waste as well as medical, hospital, and household effluents. Adsorption technology is a highly efficient approach to reduce the IBP in the aquatic environment, particularly at low IBP concentrations. Due to the exceptional surface properties of carbonaceous materials, they are considered ideal adsorbents for the IBP removal of, with high binding capacity. Given the importance of the topic, the adsorptive removal of IBP from effluent using various carbonaceous adsorbents, including activated carbon, biochar, graphene-based materials, and carbon nanostructures, has been compiled and critically reviewed. Furthermore, the adsorption behavior, binding mechanisms, the most effective parameters, thermodynamics, and regeneration methods as well as the cost analysis were comprehensively reviewed for modified and unmodified carbonaceous adsorbents. The compiled studies on the IBP adsorption shows that the IBP uptake of some carbon-based adsorbents is significantly than that of commercial activated carbons. In the future, much attention is needed for practical utilization and upscaling of the research findings to aid the management and sustainability of water resource.

Adsorption of cationic and anionic dyes onto coffee grounds cellulose/sodium alginate double-network hydrogel beads: Isotherm analysis and recyclability performance

This work describes the preparation of new eco-friendly adsorbents with a simple method. Gel beads of coffee grounds cellulose (CGC) and sodium alginate (SA) were prepared for wastewater treatment. Upon their synthesis, the physicochemical properties, performances and efficiency were analyzed by means of various structural and morphological characterizations. Kinetic and thermodynamic adsorption approaches evaluated the removal capacity of these beads which reached equilibrium in 20 min for Methylene Blue (MB) and Congo Red (CR). Also, the kinetics shows that the results can be explained by the pseudo-second-order model (PSO). Furthermore, the isotherm assessments showed that Langmuir-Freundlich can fit the adsorption data of both contaminants. Accordingly, the maximum adsorption capacities reached by the Langmuir-Freundlich model are 400.50 and 411.45 mg/g for MB and CR, respectively. It is interesting to note that the bio-adsorption capabilities of MB and CR on bead hydrogels decreased with temperature. Besides, the results of the thermodynamic study evidenced that the bio-adsorption processes are favorable, spontaneous and exothermic. The CGC/SA gel beads are therefore outstanding bio-adsorbents, offering a great adsorptive performance and regenerative abilities.

Adsorption of nitrophenol onto a novel Fe3O4-κ-carrageenan/MIL-125(Ti) composite: process optimization, isotherms, kinetics, and mechanism

Water pollution is a dreadful affair that has incessantly aggravated, exposing our planet to danger. In particular, the persistent nitro aromatic compound like nitrophenols causes anxiety to the researchers due to their hazardous impacts, excessive usage, and removal difficulty. For this purpose, a novel multi-featured composite was constructed based on κ-Carrageenan (κ-Carr), MOF (MIL-125(Ti)), and magnetic Fe3O4 for efficient adsorptive removal of o-nitrophenol (o-NP). Interestingly, BET measurements revealed the high surface area of Fe3O4-κ-Carr/MIL-125(Ti) of about 163.27 m2/g, while VSM showed its excellent magnetic property (20.34 emu/g). The comparison study pointed out the synergistic effect between Fe3O4, κ-Carr, and MIL-125(Ti), forming a composite with an excellent adsorption performance toward o-NP. The adsorption data obeyed pseudo-second-order kinetic model, and Freundlich isotherm model was better fitted than Langmuir and Temkin. Furthermore, Langmuir verified the supreme adsorption capacity of o-NP onto Fe3O4-κ-Carr/MIL-125(Ti) since the computed qmax reached 320.26 mg/g at pH 6 and 25 °C. Furthermore, the XPS results postulated that the adsorption mechanism pf o-NP proceeded via H-bonding, π-π interaction, and electron donor-acceptor interactions. Interestingly, Fe3O4-κ-Carr/MIL-125(Ti) composite retained good adsorption characteristics after reusing for five cycles, suggesting its viable applicability as an efficient, renewable, and easy-separable adsorbent for removing nitro aromatic pollutants.

Synthesis of nanomagnetite/copper oxide/potassium carrageenan nanocomposite for the adsorption and Photo-Fenton degradation of Safranin-O: kinetic and thermodynamic studies

In the current study, a novel nanomaterial called nanomagnetite/copper oxide/potassium carrageenan nanocomposite (MKCO) was fabricated to include Fenton (nanomagnetite, NM) and Fenton-like reagent (copper oxide nanoparticles, NCO) in a matrix of potassium carrageenan biopolymer. The prepared solid materials were characterized by different physicochemical techniques, such as TGA, N2 adsorption/desorption, SEM, TEM, XRD, DRS, pHPZC, and FTIR. The prepared MKCO showed unique properties like higher specific surface area of 652.50 m2/g, pore radius of 1.19 nm, pHPZC equals 7.80, and the presence of different surface chemical functional groups. Under various application conditions, comparative experiments between Safranin-O dye (SO) adsorption and Photo-Fenton catalytic degradation were conducted. After 24 h, MKCO had a maximum adsorption capacity of 384.61 mg/g at 42 °C, while the Photo-Fenton oxidation process took only 10 min to totally decompose 93% of SO at 21 °C. Based on the higher values of correlation coefficients, Langmuir’s adsorption model is the best-fitted adsorption model for SO onto all the prepared solid materials. Studies on SO adsorption’s kinetics and thermodynamics show that it is physisorption and that it operates according to endothermic, spontaneous, and PFO model processes. While, PFO, endothermic, and non-spontaneous processes are satisfied by the catalytic decomposition of SO. After five application cycles, MKCO demonstrated good catalyst reusability with a 3.4% decrease in degrading efficiency. For lower contaminant concentrations and shorter application times, Photo-Fenton catalytic degradation of organic pollutants is more effective than adsorption.

Graphical abstract

Fenton and Photo-Fenton degradation of Safranin-O

Effective and Efficient Porous CeO2 Adsorbent for Acid Orange 7 Adsorption

A porous CeO₂ was synthesized following the addition of guanidine carbonate to a Ce³⁺ aqueous solution, the subsequent addition of hydrogen peroxide and a final hydrothermal treatment. The optimal experimental parameters for the synthesis of porous CeO₂, including the amounts of guanidine carbonate and hydrogen peroxide and the hydrothermal conditions, were determined by taking the adsorption efficiency of acid orange 7 (AO7) dye as the evaluation. A template-free hydrothermal strategy could avoid the use of soft or hard templates and the subsequent tedious procedures of eliminating templates, which aligned with the goals of energy conservation and emission reduction. Moreover, both the guanidine carbonate and hydrogen peroxide used in this work were accessible and eco-friendly raw materials. The porous CeO₂ possessed rapid adsorption capacities for AO7 dye. When the initial concentration of AO7 was less than 130 mg/L, removal efficiencies greater than 90.0% were obtained, achieving a maximum value of 97.5% at [AO7] = 100 mg/L and [CeO₂] = 2.0 g/L in the first 10 min of contact. Moreover, the adsorption-desorption equilibrium between the porous CeO₂ adsorbent and the AO7 molecule was basically established within the first 30 min. The saturated adsorption amount of AO7 dye was 90.3 mg/g based on a Langmuir linear fitting of the experimental data. Moreover, the porous CeO₂ could be recycled using a NaOH aqueous solution, and the adsorption efficiency of AO7 dye still remained above 92.5% after five cycles. This study provided an alternative porous adsorbent for the purification of dye wastewater, and a template-free hydrothermal strategy was developed to enable the design of CeO₂-based catalysts or catalyst carriers.

Mesoporous crosslinked chitosan-activated clinoptilolite biocomposite for the removal of anionic and cationic dyes

A mesoporous crosslinked chitosan-activated clinoptilolite biocomposite (CS-GA/ACP) was prepared with chitosan (CS) as the substrate and glutaraldehyde (GA) as the crosslinking agent. Structural analysis of the CS-GA/ACP composite beads was performed using FTIR, SEM, and BET techniques. The adsorption properties of the CS-GA/ACP for Congo red (CR) and methylene blue (MB) removal were examined using a batch method. The effects of CS loading, CS-GA/ACP dosages (0.005-0.25 g), pH values (3-11), initial concentrations (30-300 mg/L), contact time (5-120 min), ionic strength, and temperatures (25-65 ℃) on the adsorption of CR and MB on the CS-GA/ACP composite beads were investigated. The pseudo-second-order kinetics could better describe the adsorption process than the pseudo-first-order kinetics, and the Langmuir isotherms model agreed well with the experimental data. The maximum adsorption capacities of the CS-GA/ACP for CR and MB were 180.59 mg/g and 143.67 mg/g at 25 ℃, respectively. The proposed mechanism studies showed that the possible interaction between the adsorbent and dye molecules were Yoshida H-bonding, dipole-dipole H-bonding, electrostatic interaction and n-π interaction. The CS-GA/ACP can be recycled to remove dyes without significant loss of efficacy, and the adsorption of dyes on the CS-GA/ACP is spontaneous endothermic adsorption. Overall, the CS-GA/ACP showed an excellent performance for dyes removal in aqueous solution and could be a practical candidate for industrial applications.

Substantial improvement in the adsorption behavior of montmorillonite toward Tartrazine through hexadecylamine impregnation

In the present work, the surface of montmorillonite K10 was successfully modified by hexadecylamine surfactant (Mt-HDA) and its intercalation and characteristics were assessed by XRD, FTIR, SEM, EDX and BET methods. Also, its adsorption performance was systematically examined in the removal of Tartrazine (TZ), as a sulfonated azo dye model, from aqueous phase. Our results showed that the HDA modification remarkably improved the adsorption ability of montmorillonite toward TZ molecules. The highest adsorption efficiency was achieved >98% at the pH range of 4-6 within a fast process (less than 30 min). The maximum adsorption capacity Mt-HDA toward TZ molecules was found to be ~59 mg/g at 45 °C. The kinetic study indicated that the adsorption kinetic follows pseudo-second-order model, which shows the chemisorption process between Mt-HDA and TZ molecules. Besides, the adsorption isotherm showed the monolayer coverage of Mt-HDA surface adsorption sites, which was fitted with the Langmuir isotherm model in an exothermic process. The adsorption mechanism was studied.

The surfactant-ionic liquid bi-functionalization of chitosan beads for their adsorption performance improvement toward Tartrazine

In this study, the ionic liquid (Aliquat-336) and anionic surfactant (cetyltrimethylammonium bromide, CTAB) bi-functionalized chitosan beads were prepared and characterised using different techniques, including FTIR, XRD, SEM, EDS and BET surface area analysis. The characteristic analysis confirmed the successful conjugation of chitosan beads with both surfactant and ionic liquid. The novel fabricated beads (CS-CTAB-AL) were efficiently employed, as a high-performance adsorbent, for the removal of Tartrazine (TZ), an anionic food dye, from polluted water. The optimum adsorption of TZ onto the CS-CTAB-AL was found at 2 g L^-1 of adsorbent in the wide pH range of 4-11, whereas just 45 min was required to reach more than 90% adsorption efficiency in the studied conditions. Also, the adsorption and kinetic studies showed that the experimental data well fitted the pseudo-first-order kinetic model and the Langmuir isotherm model. The maximum adsorption capacity of prepared beads was found to be 45.95 mg g^-1 at 45 °C. The adsorption properties of enabling CS-CTAB-AL conjugation introduced a new type of adsorbents, exploited the combination of ionic liquid and surfactant capabilities for wastewater treatment.

Removal of metal ions using a new magnetic chitosan nano-bio-adsorbent; A powerful approach in water treatment

In this study, a magnetic chitosan/Al₂O₃/Fe₃O₄ (M-Cs) nanocomposite was developed by ethylenediaminetetraacetic acid (EDTA) functionalization to enhance its adsorption behavior for the removal of Cd(II), Cu(II) and Zn(II) metal ions from aqueous solution. The results revealed that the EDTA functionalization of M-Cs increased its adsorption capacity ~9.1, ~5.6 and ~14.3 times toward Cu, Cd and Zn ions. The maximum adsorption capacity followed the order of Cd(II) > Cu(II) > Zn(II) and the maximum adsorption efficiency was achieved at pH of 5.3 with the removal percentage of 99.98, 93.69 and 83.81 %, respectively, for the removal of Cu, Cd and Zn ions. The metal ions adsorption kinetic obeyed pseudo-second-order equation and the Langmuir isothermal was found the most fitted model for their adsorption isothermal experimental data. In addition, the thermodynamic study illustrated that the adsorption process was exothermic and spontaneous in nature.

Adsorptive removal of organic pollutant methylene blue using polysaccharide-based composite hydrogels

Methylene blue (MB) is categorized as an organic dye (OD) released as effluents after various industrial activities and is one of the most abundant pollutants in the aquatic environment. Significantly, because of its potential toxicity, removing MB from wastewater has been a matter of necessity in recent times. Numerous analytical techniques have been applied, among which polysaccharide-based composite hydrogels appear as the most favorable for MB removal because of their large surface area, excellent mechanical properties, swelling capability, and large-scale production. In this review, the first section gives adequate information about the ODs' adverse effects on the environment and the contribution of polysaccharide-based hydrogels for OD removal, especially MB. Next, various mechanisms such as electrostatic interactions, π-π interactions, hydrogen bonding, hydrophobic interaction, van der Waals force, and coordination interaction involved in the adsorption technique are investigated. The third section extensively describes the MB removal by incorporation of various materials such as monomers, metal oxides, magnetic nanoparticles, and clay into the polysaccharide matrix to produce composite hydrogels. Finally, the current limitations and future perspectives of the polysaccharide-based composite hydrogel techniques are addressed. Overall, this review acknowledged the vital role of polysaccharide-based composite hydrogels for MB adsorption by surveying 110 research articles published in the past five years (2015-2021).

Effect of nanoemulsion-loaded hybrid biopolymeric hydrogel beads on the release kinetics, antioxidant potential and antibacterial activity of encapsulated curcumin

Nanoemulsion encapsulated in the hydrogel beads are important entrants for loading hydrophobic active ingredients for enhancing their bioavailability and biological activities relevant in the pharmaceutical, food and cosmetic industries. Herein, we report the formulation of curcumin-loaded nanoemulsion encapsulated in ionotropic hybrid hydrogel beads of alginate, chitosan, gelatin and polyethylene oxide for effective delivery of curcumin. The release behaviour in simulated gastric and intestinal fluids (SGF and SIF) at 37 °C showed faster release in SGF which could be explained on the basis of mesh size, the extent of hydration and the complexation of the curcumin with the Ca2+ ions present within the hydrogel network. The free radical scavenging and antibacterial activities of the released curcumin in SGF were significantly greater than in SIF. This study shows promises of such hybrid systems, ignored so far, for proper encapsulation, protection and delivery of curcumin for the development of functional foods and pharmaceutics. The high structural stability of these nanoemulsion carriers and their effective delivery of curcumin provide a novel and tailored formulation out of existing polymers with plethora of advantages for oral drug delivery. Moreover, this study opens new door for different possibilities to improve the physicochemical characteristics and delivery of bioactive molecules like curcumin.

Fly ash modified magnetic chitosan-polyvinyl alcohol blend for reactive orange 16 dye removal: Adsorption parametric optimization

A magnetic biocomposite blend of chitosan-polyvinyl alcohol/fly ash (m-Cs-PVA/FA) was developed by adding fly ash (FA) microparticles into the polymeric matrix of magnetic chitosan-polyvinyl alcohol (m-Cs-PVA). The effectiveness of m-Cs-PVA/FA as an adsorbent to remove textile dye (reactive orange 16, RO16) from aquatic environment was evaluated. The optimum adsorption key parameters and their significant interactions were determined by Box-Behnken Design (BBD). The analysis of variance (ANOVA) indicates the significant interactions can be observed between m-Cs-PVA/FA dose with solution pH, and m-Cs-PVA/FA dose with working temperature. Considering these significant interactions, the highest removal of RO16 (%) was found 90.3% at m-Cs-PVA/FA dose (0.06 g), solution pH (4), working temperature (30 °C), and contact time (17.5 min). The results of adsorption kinetics revealed that the RO16 adsorption was better described by the pseudo-second-order model. The results of adsorption isotherm indicated a multilayer adsorption process as well described by Freundlich model with maximum adsorption capacity of 123.8 mg/g at 30 °C. An external magnetic field can be easily applied to recover the adsorbent (m-Cs-PVA/FA). The results supported that the synthesized m-Cs-PVA/FA presents itself as an effective and promising adsorbent for textile dye with preferable adsorption capacity and separation ability during and after the adsorption process.

Novel 1-butyl-3-methylimidazolium bromide impregnated chitosan hydrogel beads nanostructure as an efficient nanobio-adsorbent for cationic dye removal: Kinetic study

In the present study, a novel 1-butyl-3-methylimidazolium bromide (BmImBr) impregnated chitosan beads were prepared and characterized using different methods, including XRD, FT-IR, EDX, SEM and BET. The FTIR analysis revealed that the BmImBr was successfully conjugated with the chitosan in the beads structure. The prepared beads were used as an efficient sorbent for the fast removal of methylene blue, as cationic dye model, from aqueous solution, whereas just 25 min was required to reach 86% removal efficiency. The increasing of BmImBr amount improved the adsorption performance of prepared beads. Also, it was found that the dye can be higher adsorbed on the beads surface by increasing the sorbent dosage and pH of solution, while the optimum dosage and pH were obtained 3 mg/L and 11, respectively. The kinetic study showed that the MB adsorption onto the CS-BmImBr beads follows the pseudo-fist order model and the intrinsic penetration controls the adsorption process. The properties of prepared chitosan- BmImBr IL conjugation confirmed that it can be exploited as an efficient adsorbent in the wastewater treatment.