Synthesis and characterization of magnetic ZnCl2-activated carbon produced from coconut shell for the adsorption of methylene blue

Reclaiming Selenium from Water Using Aluminum-Modified Biochar: Adsorption Behaviors, Mechanisms, and Effects on Growth of Wheat Seedlings

Although selenium is an essential nutrient, its contamination in water poses serious risks to human health and ecosystems. In this study, aluminum-modified bamboo biochar (Al-BC) was developed to reclaim Se(VI) from water. Compared to pristine biochar (BC), Al-BC had a larger specific surface area (176 m2/g) and pore volume (0.180 cm³/g). The modification, achieved by loading AlOOH and Al2O3 particles onto the surface, enabled Al-BC to achieve a maximum adsorption capacity of 37.6 mg/g for Se(VI) within 2 hours and remove 99.6% of Se(VI) across a pH range of 3-10. The main adsorption mechanism of Se(VI) involved electrostatic attraction, forming outer-sphere complexes between Se(VI) and AlOOH sites on the biochar. The bioavailability of Se sorbed on the spent biochar (Al-BC-Se) was thus evaluated. It was discovered that Al-BC-Se successfully released Se(VI), which impacted the growth of wheat seedlings. The Se content reached 134 μg/g dry weight (DW) in wheat shoots and 638 μg/g DW in roots, significantly exceeding normal selenium content (<40 μg/g DW). By successfully applying the modified biochar to capture selenium from water through adsorption and then reusing it as an essential nutrient in soil, this study suggests the promising feasibility of the "removal-collection-reuse" approach for the circular economy of selenium in wastewater.

Application of Optimization Response Surface for the Adsorption of Methylene Blue Dye onto Zinc-coated Activated Carbon

The activated carbon was produced in the first phase of this investigation by chemically activating hazelnut shell waste with H3PO4. Composite materials were obtained by coating the activated carbon with zinc oxide, whose BET surface area was calculated as 1278 m2 g-1. ZnO-doped ZnO/AC composite was synthesized as an adsorbent for its possible application in the elimination of organic dyestuff MB, and its removal efficiency was investigated. Morphological properties of ZnO/AC were characterized using analytical methods such as XRD, SEM, and BET. The adsorption system and its parameters were investigated and modeled using the response surface method of batch adsorption experiments. The experimental design consisted of three levels of pH (3, 6.5, and 10), initial MB concentration (50, 100, and 150 mg L-1), dosage (0.1, 0.3, and 0.5 g 100 mL-1), and contact time (5, 50, and 95 min). The results from the RSM suggested that the MB removal efficiency was 98.7% under the optimum conditions of the experimental factors. The R2 value, which expresses the significance of the model, was determined as 99.05%. Adsorption studies showed that the equilibrium data fit well with the Langmuir isotherm model compared to Freundlich. The maximum adsorption capacity was calculated as 270.70 mg g-1.

Amendment of Sargassum oligocystum bio-char with MnFe2O4 and lanthanum MOF obtained from PET waste for fluoride removal: A comparative study

The use of biomass and waste to produce adsorbent reduces the cost of water treatment. The bio-char of Sargassum oligocystum (BCSO) was modified with MnFe2O4 magnetic particles and La-metal organic framework (MOF) to generate an efficient adsorbent (BCSO/MnFe2O4@La-MOF) for fluoride ions (F-) removal from aqueous solutions. The performance of BCSO/MnFe2O4@La-MOF was compared with BCSO/MnFe2O4 and BCSO. The characteristics of the adsorbents were investigated using various techniques, which revealed that the magnetic composites were well-synthesized and exhibited superparamagnetic properties. The maximum adsorption efficiencies (BCSO: 97.84%, BCSO/MnFe2O4: 97.85%, and BCSO/MnFe2O4@La-MOF: 99.36%) were achieved under specific conditions of pH 4, F- concentration of 10 mg/L, and adsorbent dosage of 3, 1.5, and 1 g/L for BCSO, BCSO/MnFe2O4, and BCSO/MnFe2O4@La-MOF, respectively. The results demonstrated that the experimental data adheres to a pseudo-second-order kinetic model. The enthalpy, entropy, and Gibbs free energy were determined to be negative; thus, the F- adsorption was exothermic and spontaneous in the range of 25-50 °C. The equilibrium data of the process exhibited conformity with the Langmuir model. The maximum adsorption capacities of F- ions were determined as 10.267 mg/g for BCSO, 14.903 mg/g for the BCSO/MnFe2O4, and 31.948 mg/g for BCSO/MnFe2O4@La-MOF. The KF and AT values for the F- adsorption were obtained at 21.03 mg/g (L/mg)1/n and 100 × 10+9 L/g, indicating the pronounced affinity of the BCSO/MnFe2O4@La-MOF towards F- than other samples. The significant potential of the BCSO/MnFe2O4@La-MOF magnetic composite for F- removal from industrial wastewater, makes it suitable for repeated utilization in the adsorption process.

Enhanced fluoride removal using montmorillonite clay modified with CoFe2O4 and metal-organic frameworks

The use of modified clays can play an effective role as an effective adsorbent in removing fluoride (Flu) ions from water and aqueous solutions. In the present research, montmorillonite clay (MMt) was modified using CoFe2O4 magnetic particles and Al-Fe fumarate metal-organic framework (Al-Fe Fum) and was utilized as an efficient adsorbent for removing Flu from aqueous solution. The properties of MMt and MMt/CoFe2O4/Al-Fe Fum samples were investigated using different techniques. The results showed that with the modification of MMt using CoFe2O4 magnetic particles and the metal-organic framework of Al-Fe Fum, the BET surface has increased notably from 13.217 to 365.80 m2/g. To investigate the effect of independent variables and their interaction on the efficiency of the Flu adsorption, response surface method-central compound design (RSM-CCD) was served. Based on the results of ANOVA, the F-value and p-value parameters for the desired model were determined to be 783.09 and < 0.0001, respectively, which confirms the success and high ability of the model. The number of R2, adjusted R2, and Predicted R2 for adsorption of Flu ion was determined to be 0.998, 0.997, and 0.995, respectively, which shows that the proposed regression model can describe the process of adsorption and interaction between variables well. Compared to other kinetic models, the pseudo 2nd order kinetic model has a greater ability to describe the Flu adsorption behavior. The R2 parameter value determined that the Freundlich isotherm model has a suitable ability to investigate the isotherm behavior and confirms the effect of heterogeneous surfaces in the process. Generally, the outcomes signified that the MMt and MMt/CoFe2O4/Al-Fe Fum samples can be reused several times in the process of Flu adsorption, while the efficiency is more than 90%.

Mesoporous activated carbon derived from fruit by-product by pyrolysis induced chemical activation: optimization and mechanism for fuchsin basic dye removal

In this study, pineapple crown (PC) feedstock residues were utilized as a potential precursor toward producing activated carbon (PCAC) via pyrolysis induced with ZnCl2 activation. The PCAC has a surface area (457.8 m2/g) and a mesoporous structure with an average pore diameter of 3.35 nm, according to the Brunauer-Emmett-Teller estimate. The removal of cationic dye (Fuchsin basic; FB) was used for investigating the adsorption parameters of PCAC. The optimization of significant adsorption variables (A: PCAC dose (0.02-0.1 g/100 mL); B: pH (4-10); C: time (10-90); and D: initial FB concentration (10-50 mg/L) was conducted using the Box-Behnken design (BBD). The pseudo-second-order (PSO) model characterized the dye adsorption kinetic profile, whereas the Freundlich model reflected the equilibrium adsorption profile. The maximum adsorption capacity (qmax) of PCAC for FB dye was determined to be 171.5 mg/g. Numerous factors contribute to the FB dye adsorption mechanism onto the surface of PCAC, which include electrostatic attraction, H-bonding, pore diffusion, and π-π stacking. This study illustrates the utilization of PC biomass feedstock for the fabrication of PCAC and its successful application in wastewater remediation.

Activated carbon and their nanocomposites derived from vegetable and fruit residues for water treatment

Water pollution remains a pressing environmental issue, with diverse pollutants such as heavy metals, pharmaceuticals, dyes, and aromatic hydrocarbon compounds posing a significant threat to clean water access. Historically, biomass-derived activated carbons (ACs) have served as effective adsorbents for water treatment, owing to their inherent porosity and expansive surface area. Nanocomposites have emerged as a means to enhance the absorption properties of ACs, surpassing conventional AC performance. Biomass-based activated carbon nanocomposites (ACNCs) hold promise due to their high surface area and cost-effectiveness. This review explores recent advancements in biomass-based ACNCs, emphasizing their remarkable adsorption efficiencies and paving the way for future research in developing efficient and affordable ACNCs. Leveraging real-time communication for ACNC applications presents a viable approach to addressing cost concerns.

Studies on the Process of Basic Dyes Adsorption on Uniform Spherical Carbons

The influence of carbon pore structure on the sorption process of selected cationic dyes has been investigated. The structure and surface of carbonaceous materials have been characterized basing on various techniques: scanning electron microscopy, low temperature nitrogen adsorption-desorption measurements, X-ray photoelectron spectroscopy and thermal analysis combined with identification of gaseous products. The kinetic and equilibrium adsorption measurements of Basic Violet 3, Basic Red 1 and Basic Blue 9 from aqueous media were performed. The studied carbons seem to be promising adsorbents towards dyes, taking into account the easy-to-use uniform spherical form of the granules and a complex type of porosity with micro-, meso- and macropores appropriate for large molecule adsorption.

Zanthoxylum bungeanum Waste-Derived High-Nitrogen Self-Doped Porous Carbons as Efficient Adsorbents for Methylene Blue

In this study, we prepared high-nitrogen self-doped porous carbons (NPC1 and NPC2) derived from the pruned branches and seeds of Zanthoxylum bungeanum using a simple one-step method. NPC1 and NPC2 exhibited elevated nitrogen contents of 3.56% and 4.22%, respectively, along with rich porous structures, high specific surface areas of 1492.9 and 1712.7 m2 g-1 and abundant surface groups. Notably, both NPC1 and NPC2 demonstrated remarkable adsorption abilities for the pollutant methylene blue (MB), with maximum monolayer adsorption capacities of 568.18 and 581.40 mg g-1, respectively. The adsorption kinetics followed the pseudo-second-order kinetics and the adsorption isotherms conformed to the Langmuir isotherm model. The adsorption mechanism primarily relied on the hierarchical pore structures of NPC1 and NPC2 and their diverse strong interactions with MB molecules. This study offers a new approach for the cost-effective design of nitrogen self-doped porous carbons, facilitating the efficient removal of MB from wastewater.

Efficient dye adsorption of mesoporous activated carbon from bamboo parenchyma cells by phosphoric acid activation

In order to solve the environmental damage caused by the discharge of dyes as industrial wastewater, the development of efficient and sustainable adsorbents is the key, while most of the previous studies on bamboo parenchyma cells have focused on their microstructural, functional and mechanical properties, and few of the properties in adsorption have been investigated. To evaluate the role of the unique microstructure of bamboo parenchyma cells on adsorption after carbonization and activation, PC-based activated carbon (PPAC) was fabricated by the phosphoric acid activation method and tested for adsorption using methylene blue (MB). The effect of mesoporous structure on MB adsorption was investigated in detail using PPAC-30C impregnated with phosphoric acid at a concentration of 30%. The results showed that the adsorption performance was influenced by single-factor experiments (e.g., pH, activated carbon dosing). The adsorption isotherms and kinetics could conform to the Langmuir model (R2 = 0.983-0.994) and pseudo-second-order kinetic model (R2 = 0.822-0.991) respectively, and the maximum MB adsorption capacity of adsorbent was 576 mg g-1. The adsorption mechanism of MB on PPAC-30C includes physical adsorption, electrostatic attraction, hydrogen bonding, and the π-π conjugation effect, which was dominated by physical adsorption. The results of this study show that PPAC has good application prospects for cationic dye removal.

Fabrication of date palm kernel biochar-sulfur (DPKB-S) for super adsorption of methylene blue dye from water

A novel form of biochar was created by dehydration of Date palm kernel with 85% sulfuric acid. It was examined how the newly produced biochar (DPKB-S) affected the aqueous solution's capacity to extract Methylene Blue (MB) dye. The prepared DPKB-S was categorized by BET, BJH, FT-IR, SEM, EDX, DSC, and TGA analyses. The ideal pH for the MB dye adsorption by DPKB-S is 8. With 0.75 g L-1 of DPKB-S and an initial concentration of 50 ppm MB dye, Date Palm Kernel Biochar-Sulfur (DPKB-S) had the highest removal percentage of 100%. The Langmuir and Freundlich isotherm models were used to investigate the collected data. Freundlich model is the model that best covers MB dye adsorption in DPKB-S at low concentrations (0.75-1.25 g L-1) and the Langmuir model at high concentrations (1.5-1.75 g L-1). The Langmuir model maximum adsorption capacity (Qm) of the DPKB-S was 1512.30 mg g-1. Furthermore, a variety of error function models were applied to investigate the isotherm models derived data, including Marquardt's percent standard deviation (MPSD), the sum of absolute errors (EABS), the sum of the errors squared (ERRSQ), root mean square errors (RMS), Chi-square error (X2), the average relative error (ARE), average percent errors (APE), and hybrid error function (HYBRID). Kinetic data were calculated by intraparticle diffusion (IPD), pseudo-second-order (PSO), pseudo-first-order (PFO), and film diffusion (FD) models. A PSO rate model with a strong correlation (R2 = 1.00) largely regulated the adsorption rate. The removal mechanism of MB dye by DPKB-S is based on the principle that these positively charged dyes are attracted by electrostatic attraction forces due to the growth in the number of negatively charged regions at basic pH value. According to the results, DPKB-S shows promise as an affordable and competent adsorbent for the adsorption of MB dye. It can be used frequently without experiencing a discernible decrease in adsorption efficiency.

High surface area activated carbon from a pineapple (ananas comosus) crown via microwave-ZnCl2 activation for crystal violet and methylene blue dye removal: adsorption optimization and mechanism

In this investigation, microwave irradiation assisted by ZnCl2 was used to transform pineapple crown (PN) waste into mesoporous activated carbon (PNAC). Complementary techniques were employed to examine the physicochemical characteristics of PNAC, including BET, FTIR, SEM-EDX, XRD, and pH at the point-of-zero-charge (pHpzc). PNAC is mesoporous adsorbent with a surface area of 1070 m2/g. The statistical optimization for the adsorption process of two model cationic dyes (methylene blue: MB and, crystal violet: CV) was conducted using the response surface methodology-Box-Behnken design (RSM-BBD). The parameters include solution pH (4-10), contact time (2-12) min, and PNAC dosage (0.02-0.1 g/100 mL). The Freundlich and Langmuir models adequately described the dye adsorption isotherm results for the MB and CV systems, whereas the pseudo-second order kinetic model accounted for the time dependent adsorption results. The maximum adsorption capacity (qmax) for PNAC with the two tested dyes are listed: 263.9 mg/g for CV and 274.8 mg/g for MB. The unique adsorption mechanism of MB and CV dyes by PNAC implicates multiple contributions to the adsorption process such as pore filling, electrostatic forces, H-bonding, and π-π interactions. This study illustrates the possibility of transforming PN into activated carbon (PNAC) with the potential to remove two cationic dyes from aqueous media.

Statistical physics modeling study of an environmentally friendly and efficient adsorbent derived from the brown macroalgae Bifurcaria bifurcata for the removal of Bisphenol A

The brown macroalgae Bifurcaria bifurcata was valued and used to develop a carbonaceous material activated by H2SO4 (AC-BB@H2SO4), with the goal of assessing its adsorption ability against Bisphenol A (BPA). During the adsorption experiments, the effects of the adsorbent dose, solution pH, and contact time were examined, and the results were m = 0.4 g/L, pH = 8.3, and t = 120 min, with an elimination yield of 91.6 %. With comparatively high R2 values, the pseudo-second-order kinetic model perfectly fitted the experimental data. Langmuir's model was found to be the best appropriate for describing the adsorption equilibrium of BPA on AC-BB@H2SO4. The thermodynamic findings show that BPA adsorption on AC-BB@H2SO4 was spontaneous, favorable, and endothermic in nature. Even after six cycles of reuse, regeneration testing demonstrated that our adsorbent could eliminate BPA by >50 %. The BPA adsorption mechanism's statistical physics control parameters were determined and analyzed. BPA's adsorption energies were <40 kJ/mol, indicating that the interactions between BPA and AC-BB@H2SO4 were governed by physical forces (i.e., hydrogen bonding and van der Waals and electrostatic interactions). All of these intriguing findings indicate that our carbonaceous material might have direct ramifications in the field of wastewater treatment, notably for the clearance of BPA, which is difficult to biodegrade.

Novel adsorbent for malachite green from okra stalks waste: synthesis, kinetics and equilibrium studies

In this study, malachite green (MG) removal was performed with activated carbon synthesized from okra stalks by microwave assisted chemical activation method. In the synthesis of activated carbon, the effects of gas in the microwave, activation, and impregnation rate were investigated. The synthesized activated carbon characterization was investigated using BET, FT-IR, and SEM analyses. The activated carbon surface area achieved was 759.453 m2 g-1. In addition, the surface area of activated carbon synthesized using the conventional method was17.766 m2 g-1. The effect of the initial solution concentration on MG adsorption was investigated. According to the kinetic and equilibrium data, it was found that the adsorption process best fitted the pseudo-second order kinetic model and the Langmuir isotherm. According to the equilibrium data, the maximum adsorption capacity (qmax) of the monolayer was 119.05 mg g-1. In addition, MG adsorption was investigated by the experimental design method. The adsorption capacity at the determined optimum conditions was 99.63 mg g-1. All results show that activated carbon synthesized from waste biomass by combining the conventional method with microwave-assisted impregnation is a cheap and environmentally friendly adsorbent.

An innovative outlook on utilization of agro waste in fabrication of functional nanoparticles for industrial and biological applications: A review

The burning of an agro waste residue causes air pollution, global warming and lethal effects. To overcome these obstacles, the transformation of agro waste into nanoparticles (NPs) reduces industrial expenses and amplifies environmental sustainability. The concept of green nanotechnology is considered as a versatile tool for the development of valuable products. Although a plethora of literature on the NPs is available, but, still scientists are exploring to design more novel particles possessing unique shape and properties. So, this review basically summarises about the synthesis, characterizations, advantages and outcomes of the various agro waste derived NPs.

Removal of methylene blue by acrylic polymer adsorbents loaded with magnetic iron manganese oxides: Synthesis, characterization, and adsorption mechanisms

Dyes pose significant risks for aquatic environments and biological health in general owing to their non-biodegradable nature, carcinogenicity, and toxicity. The effective treatment of dye wastewater has become an important research topic. In this study, acrylic polymers (AP) loaded with magnetic iron manganese oxides (MIMO) (AP/MIMO) were prepared and used for the first time for the adsorption of methylene blue (MB). Carbon in AP/MIMO exists predominantly in the C-H and C-C forms, with its content reaching 50.7%. Oxygen and nitrogen in AP/MIMO exist mainly in the -CO- and -N-C forms, with contents of up to 41.5% and 73.3%, respectively. MB removal by AP/MIMO was consistent with the pseudo-second-order kinetic model (R2 = 0.99), equilibrium was achieved within 20 min, and the highest MB capacity of 2611.23 mg g-1 was predicted by the Langmuir isotherm model (R2 = 0.91-0.94). AP/MIMO exhibited excellent MB adsorption performance in the pH range of 4-10, with a removal efficiency higher than 99.0% (MB = 100 mL 1000 mg L-1; AP/MIMO = 50 mg). Thermodynamic indicators, such as positive entropy (ΔS0; 98.30 J⋅mol-1⋅K-1), negative Gibbs free energy (ΔG0; -29.40, -28.50, and -27.50 KJ⋅mol-1), and positive enthalpy (ΔH0; 2.30 KJ⋅mol-1), demonstrated that MB removal by AP/MIMO was autonomous, favorable, and endothermic. In addition, the integration of experimental results and theoretical calculations verified that electrostatic interactions were the primary mechanism for MB adsorption at carboxyl sites on AP/MIMO. The total interaction energy between AP and MB was -310.43 kJ⋅mol-1, and the electrostatic effect had a decisive contribution to the MB adsorption, with a value of up to -341.06 kJ⋅mol-1. AP and MB were most likely bound by -COO and S atoms. Overall, AP/MIMO exhibits high adsorption capacity and shows potential as a high-performance magnetic polymer for MB removal.

Magnetic activated carbon from spent coffee grounds: iron-catalyzed CO2 activation mechanism and adsorption of antibiotic lomefloxacin from aqueous medium

The facile fabrication of low-cost adsorbents possessing high removal efficiency and convenient separation property is an urgent need for water treatment. Herein, magnetic activated carbon was synthesized from spent coffee grounds (SCG) by Fe-catalyzed CO2 activation at 800 °C for 90 min, and magnetization and pore formation were simultaneously achieved during heat treatment. The sample was characterized by N2 adsorption-desorption, XRD, VSM, SEM, and FTIR. Batch adsorption experiments were conducted using lomefloxacin (LMO) as the probing pollutant. Preparation mechanism was revealed by TG-FTIR and XRD. Experimental results showed that Fe3O4 derived from Fe species can be reduced to Fe by carbon at high temperatures, followed by subsequent reoxidation to Fe3O4 by CO2, and the redox cycle between Fe and Fe3O4 favored the formation of pores. The promotion effects of Fe species on CO2 activation can be quantitatively reflected by the yield of CO as the signature gaseous product, and the suitable activation temperate range was determined to be 675 to 985 °C. The BET surface area, total pore volume, and saturated magnetization value of the product were 586 m2 g-1, 0.327 cm3 g-1, and 11.59 emu g-1, respectively. The Langmuir model was applicable for the adsorption isotherm data for LMO with the maximum adsorption capacity of 95 mg g-1, and thermodynamic analysis revealed that the adsorption process was endothermic and spontaneous. This study demonstrated that Fe-catalyzed CO2 activation was an effective method of converting SCG into magnetic separable adsorbent for LMO removal from aqueous medium.

Magnetic Hydrogel Beads as a Reusable Adsorbent for Highly Efficient and Rapid Removal of Aluminum: Characterization, Response Surface Methodology Optimization, and Evaluation of Isotherms, Kinetics, and Thermodynamic Studies

Biopolymers such as alginate and gelatin have attracted much attention because of their exceptional adsorption properties and biocompatibility. The magnetic hydrogel beads produced and used in this study had a core structure composed of magnetite nanoparticles and gelatin and a shell structure composed of alginate. The combination of the metal-ion binding ability of alginate and the mechanical strength of gelatin in magnetic hydrogel beads presents a new approach for the removal of metal from water sources. The beads were designed for aluminum removal and fully characterized using various methods, including Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy-energy-dispersive X-ray spectroscopy, vibrating sample magnetometry, microcomputed tomography, and dynamic mechanical analysis. Statistical experimental designs were employed to optimize the parameters of the adsorption and recovery processes. Plackett-Burman Design, Box-Behnken Design, and Central Composite Design were used for identifying the significant factors and optimizing the parameters of the adsorption and recovery processes, respectively. The optimum parameters determined for adsorption are as follows: pH: 4, contact time: 30 min, adsorbent amount: 600 mg; recovery time: reagent 1 M HNO3; and contact time: 40 min. The adsorption process was described by using the Langmuir isotherm model. It reveals a homogeneous bead surface and monolayer adsorption with an adsorption capacity of 5.25 mg g-1. Limit of detection and limit of quantification values were calculated as 4.3 and 14 μg L-1, respectively. The adsorption process was described by a pseudo-second-order kinetic model, which assumes that chemisorption is the rate-controlling mechanism. Thermodynamic studies indicate that adsorption is spontaneous and endothermic. The adsorbent was reusable for 10 successive adsorption-desorption cycles with a quantitative adsorption of 98.2% ± 0.3% and a recovery of 99.4% ± 2.6%. The minimum adsorbent dose was determined as 30 g L-1 to achieve quantitative adsorption of aluminum. The effects of the inorganic ions were also investigated. The proposed method was applied to tap water and carboy water samples, and the results indicate that magnetic hydrogel beads can be an effective and reusable bioadsorbent for the detection and removal of aluminum in water samples. The recovery values obtained by using the developed method were quantitative and consistent with the results obtained from the inductively coupled plasma optical emission spectrometer.

Adsorption characteristics of magnetized biochar derived from Citrus limetta peels

Agro-industrial waste is an alarming issue that needs to be addressed. Waste valorization is an effective technique to deal with such effectively. Synthesis of biochar from fruit waste is one of the emerging approaches for adsorption, energy storage, air purification, catalysis, and biogas production trending these days. Magnetized Citrus limetta biochar (MCLB) was synthesized from Citrus limetta peels and was magnetized using iron oxide. Magnetization of biochar increases its functionalities as well as makes its separation easy. The removal of Methylene Blue (MB) dye from an aqueous solution is achieved through the use of MCLB. Methylene Blue is a prominent and widely used cationic-azo dye in the textile and printing industries. The accumulation of MB in wastewater is the major problem as MB is reported as a carcinogenic agent. The removal of MB dye with MCLB was analyzed by adsorption studies, wherein the effect of factors influencing adsorption such as initial concentration of MB dye, MCLB dosage, the effect of pH, contact time, and adsorption isotherms were studied. Characterization of MCLB was carried out using various techniques, such as FTIR, VSM, XRD, SEM, RAMAN, and Zeta potential. The adsorption isotherm mechanism was well explained with the non-linear Langmuir isotherm model resulting in a good adsorption capacity (q e  = 41.57 mg/g) of MCLB when MB (co = 60 mg/L, pH ~ 6.8, T = 273K). The thermodynamics analysis revealed that MB's spontaneous and endothermic adsorption onto the MCLB surface followed pseudo-second-order kinetics. The results obtained from this study suggest that the magnetized biochar derived from Citrus limetta peels has a wide range of potential applications in the treatment of dyeing wastewater.

A comprehensive review of coconut-based porous materials for wastewater treatment and CO2 capture

For several decades, water pollution has become a major threat to aquatic and non-aquatic species, including humans. Different treatment techniques have already been proposed and implemented depending on wastewater characteristics. But many of these treatment techniques are expensive and inefficient. Adsorption-based techniques have shown impressive performances as an inexpensive treatment method previously. Coconut-based resources have been considered as adsorbents for wastewater treatment because of their abundance, low cost, and favorable surface properties. However, over the last decade, no comprehensive study has been published regarding biochar from coconut-based materials for wastewater treatment and CO2 capture. This review discusses biochar production technology for coconut-based materials, its modification and characterization, its utilization as an adsorbent for removing metals and organics from wastewater, and the associated removal mechanisms and the economic aspects of coconut-based biochar. Coconut-based materials are cheap and effective for removing various organic compounds such as pesticides, hormones, phenol, and phenolic compounds from solutions and capturing CO2 from air mainly through the pore-filling mechanism. Utilizing coconut-based biochars in a hybrid system that combines adsorption and other techniques, such as biotechnology or chemical coagulation is a promising way to increase their performance as an adsorbent in wastewater treatment.

Adsorption of methylene blue dye from aqueous solution using low-cost adsorbent: kinetic, isotherm adsorption, and thermodynamic studies

Fig leaf, an environmentally friendly byproduct of fruit plants, has been used for the first time to treat of methylene blue dye. The fig leaf-activated carbon (FLAC-3) was prepared successfully and used for the adsorption of methylene blue dye (MB). The adsorbent was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and the Brunauer-Emmett-Teller (BET). In the present study, initial concentrations, contact time, temperatures, pH solution, FLAC-3 dose, volume solution, and activation agent were investigated. However, the initial concentration of MB was investigated at different concentrations of 20, 40, 80, 120, and 200 mg/L. pH solution was examined at these values: pH3, pH7, pH8, and pH11. Moreover, adsorption temperatures of 20, 30, 40, and 50 °C were considered to investigate how the FLAC-3 works on MB dye removal. The adsorption capacity of FLAC-3 was determined to be 24.75 mg/g for 0.08 g and 41 mg/g for 0.02 g. The adsorption process has followed the Langmuir isotherm model (R² = 0.9841), where the adsorption created a monolayer covering the surface of the adsorbent. Additionally, it was discovered that the maximum adsorption capacity (Qm) was 41.7 mg/g and the Langmuir affinity constant (KL) was 0.37 L/mg. The FLAC-3, as low-cost adsorbents for methylene blue dye, has shown good cationic dye adsorption performance.

Euterpe oleracea-based biochar for clonazepam adsorption: synthesis, characterization, adsorption properties, and toxicity assays

The consumption of açaí fruit (Euterpe oleracea) has largely increased worldwide, resulting in a significant increase in the demand for its pulp. As a result, the small producing communities end up with large amounts of açaí endocarp residues, creating local environmental pollution problems. Therefore, chemical and physical routes were investigated for producing açaí endocarp adsorbents to propose a locally viable solution for this problem. The adsorption properties of the produced biochars were tested for clonazepam (CZM) removal, and the toxicity of the final solutions was evaluated. The results revealed that the chemical route generated biochar with about twice the surface area and pore volume (762 m² g^-1 and 0.098 cm³ g^-1) than the physical route (498 m² g^-1 and 0.048 cm³ g^-1). Furthermore, the Sips isotherm better described the CZM adsorption equilibrium for both biochars, with q_s values of 26.94 and 61.86 mg g^-1 for the physical- and chemical-activated adsorbents. Moreover, recycling studies were performed, and the chemical-activated biochar was stable for up to three cycles, reaching removal rates superior to 80%. Besides, the final toxicity decreased after the adsorptive treatment. Therefore, chemical activation can be used as a simple and effective method for producing stable and compelling adsorbents as an elegant way of adding value to the residues from açaí production, helping solve local environmental problems.

Black-wattle tannin/kraft lignin H3PO4-activated carbon xerogels as excellent and sustainable adsorbents

This work proposed new black-wattle tannin/kraft lignin H₃PO₄-activated carbon xerogels as sustainable and efficient adsorbents. The precursors were chosen based on their eco-friendly and cost-effective nature, aiming to achieve adsorbents with high adsorption capacities. Carbon xerogels were synthesized through polycondensation with formaldehyde and alkaline catalyst in a simple one-pot procedure. Activation was performed using H₃PO₄ in a tubular furnace (500 °C), under a nitrogen atmosphere. Results show that the inclusion of the kraft lignin led to changes in the morphology of the materials, facilitating the development of their porous structure and increasing specific surface area and pore volume. The best adsorbent (XLT 50 %) was synthesized using a 1:1 tannin/kraft lignin mass ratio. This material presented an adsorption capacity of nearly 1150 mg g^-1 of methylene blue (pH = 5 and T = 298 K), which was linked to its high specific surface area of 1348 m² g^-1. The adsorption process followed the pseudo-second-order kinetic model, whereas the adsorption isotherms were best fitted by the Sips model. The XLT 50 % presented good reusability properties, maintaining its adsorption capacity for 3 cycles. Finally, the XLT 50 % presented good adsorptive properties toward other pollutants (methyl orange, 4-chlorophenol, and hexavalent chromium), indicating its versatility for adsorption processes.

Removal of methylene blue dye from aqueous solution using an efficient chitosan-pectin bio-adsorbent: kinetics and isotherm studies

Wastewater contains organic compounds, including dyes, which have potential risks to the environment. Hence, these compound needs to be eliminated from the aqueous solution. In the present study, chitosan-pectin composite (Cs-Pc) was used as an adsorbent to remove methylene blue dye (MB) from synthetic wastewater. To evaluate the parameters affecting adsorption, including the initial MB concentration, solution pH, contact time, and Cs-Pc dose, batch experiments were carried out. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared (FTIR), and pH point of zero charges (pH pzc) were applied for characterizations of Cs-Pc. The optimum conditions were obtained with an initial MB concentration of 50 mg L^-1: solution pH ~ 11, Cs-Pc dose: 1.5 g L^-1 and 180 min contact time, which caused 97.77% of MB removal. In addition, the removal efficiency of MB was more influenced by pH than by sorbate dose. Also, Cs-Pc had a higher ability to remove MB than chitosan and pectin, probably due to its highly porous structure and rough surfaces that provides active sites and facilitate MB adsorption. The maximum removal efficiency and the adsorption capacity of MB onto Cs-Pc at 500 mg L^-1 concentration under optimum conditions were 98.67% and 328.02 mg g^-1, respectively. The adsorption kinetics and isotherms were best described by pseudo-second-order and Freundlich equation, respectively. After four times of recycling, the removal efficiency of MB was above 96%. Electrostatic and pi-pi interactions are the main mechanisms for the removal of MB onto the adsorbent. So the application of Cs-Pc is promising for MB removal from polluted solutions not only due to its strong adsorbing capability but also due to its excellent ability to reuse.

Production of xylooligosaccharides from Camellia oleifera Abel fruit shell using a shell-based solid acid catalyst

This study aimed to produce xylooligosaccharides (XOS) from Camellia oleifera Abel fruit shell (CFS) using a shell-based solid acid derived from CFS (CFS-BSA). CFS-BSA preparation was optimized by incomplete carbonization at 450 °C for 1 h, followed by sulfonation at 130 °C for 8 h to yield a -SO₃H functional group concentration of 1.04 mmol/g. When CFS-BSA was used to hydrolyze CFS with a 1:5 ratio of CFS-BSA to CFS at 170 °C for 20 min, a maximum XOS yield (X₂-X₅) of 51.41 % was achieved, which was notably higher than when using subcritical H₂O solely. CFS-BSA can be recycled and reused at least six times by sieving without a substantial loss in its catalytic activity. CFS-BSA can also be used to produce XOS from other lignocellulosic materials such as corncob (41.04 %), sugarcane bagasse (45.03 %), corn stalk (45.89 %), birchwood (46.05 %), and poplar (40.10 %).

Preparation and characterization of low-cost activated carbon from Moringa oleifera chemically activated using ZnCl2 for the adsorption of bisphenol A

The use of agricultural by-products such as Moringa oleifera plants is one effort to support the reduction of environmental pollution. Activated carbon produces from agricultural wastes is relatively less expensive and can replace traditional methods such as renewable as well as nonrenewable materials such as petroleum residue and coal. In this study, the removal of bisphenol A from aqueous media was studied using activated carbon produced from M. oleifera pods and peels. A batch adsorption study was carried out by varying the parameters of the adsorption process. A maximum removal percentage of 95.46% was achieved at optimum conditions of 2.5 g L^-1 adsorbent dose, pH 7, 60 min contact time and 20 mg L^-1 initial concentration of BPA. The BET surface areas of MOP, MOP-AC and MOP-ACZ were found to be 12.60, 4.10 and 45.96 m²/g, respectively. The experimental data were analyzed by Langmuir, Freundlich and Temkin adsorption isotherm models. Equilibrium data fitted well with the Langmuir isotherm with a maximum monolayer adsorption capacity of 20.14 mg g^-1. The rates of adsorption were found to conform to the pseudo-second-order kinetics with a good correlation. The results indicate that the M. oleifera activated carbon could be employed as a low-cost alternative to commercial activated carbon in the removal of BPA from water.

Design a flower-like magnetic graphite carbon microsphere for enhanced adsorption of 2,4-dichlorophenol

2,4-Dichlorophenol (2,4-DCP) is a hazardous chlorinated organic chemical, so its removal is an important task to protect the whole ecosystem and human health. During the material preparation, the magnetic graphitic carbon adsorbent (HFMCM) with a sparse sheet-like stacking structure was formed by interlayer assembly of nickel hydroxide nanosheets and hydrothermal glucose carbon. The conditions for optimal performance of the adsorbent are 45 °C and pH 5. The maximum adsorption capacity of HFMCM-180 for 2,4-DCP is 147.06 mg·g^-1. Adsorption behavior in accordance with Langmuir isothermal model and pseudo-second-order kinetic models. The adsorbent remains selective for 2,4-DCP in metal ion solutions. More than 75% of the adsorption capacity is maintained after five cycles of adsorption. Electrostatic interaction, hydrogen bonding, and π-π bonding play a major role in the adsorption of 2,4-DCP by HFMCM. The adsorbent was glucose as the carbon source, nickel sulfate as the magnetic source, and hexamethylenetetramine as the precipitant. Its carbonization after pretreatment with different hydrothermal temperatures resulted in the synthesis of flower-like graphitic carbon spheres with magnetic properties. The interconnected pore channels on the adsorbent surface conferred large specific surface area to the material. 2,4-DCP was efficiently adsorbed by π-π stacking, hydrogen bonding, and electrostatic attraction within the pore channels with low spatial potential resistance.

Fruit peel-based mesoporous activated carbon via microwave assisted K2CO3 activation: Box Behnken design and desirability function for methylene blue dye adsorption

A low-cost fruit waste namely watermelon peel (WMP) was utilized as a promising precursor for the preparation of mesoporous activated carbon (WMP-AC) via microwave assisted-K₂CO₃ activation. The WMP-AC was applied as an adsorbent for methylene blue dye (MB) removal. Several types of characterizations, such as specific surface area (BET), Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDX), Elemental Analysis (CHNS/O), and Fourier Transform Infrared Spectroscopy (FTIR) were used to identify the physicochemical properties of WMP-AC. Furthermore, Box-Behnken design (BBD) was applied to optimize the influence of the adsorption operational variables (contact time, adsorbent dose, working temperature, and solution pH) on MB dye adsorption. Thus, based on significant interactions, the optimum BBD output shows the best removal of 50 mg·L^-1 MB (92%) was recorded at an adsorbent dose of 0.056 g, contact time of 4.4 min, working temperature of 39 °C, and solution pH 8.4. The Langmuir uptake capacity of WMP-AC was found to be 312.8 mg·g^-1, with the best fitness to the pseudo-second-order kinetics model and an endothermic adsorption process. The adsorption mechanisms of MB by WMP-AC can be assigned to the hydrogen bonding, electrostatic attraction, and π-π stacking. The findings of this study indicate that WMP is a promising precursor for producing porous activated carbon for MB dye removal.

Nanoporous carbon materials as a sustainable alternative for the remediation of toxic impurities and environmental contaminants: A review

Due to rapidly deteriorating water resources, the world is looking forward to a sustainable alternative for the remediation of noxious pollutants such as heavy metals and organic and gaseous contaminants. To address this global issue of environmental pollution, nanoporous carbon materials (NPCMs) can be used as a one-stop solution. They are widely applied as adsorbents for many toxic impurities and environmental contaminants. The present review provides a detailed overview of the role of different synthesis factors on the porous characteristics of carbon materials, activating agents, reagent-precursor ratio and their potential application in the remediation. Findings revealed that synthetic parameters result in the formation of microporous NPCMs (S_BET: >4000 m³/g; V_Total (cm³/g) ≥ 2; V_Micro (cm³/g) ≥ 1), micromesoporous (S_BET: >2500 m³/g; V_Total (cm³/g) ≥ 1.5; V_Micro (cm³/g) ≥ 0.7) and mesoporous (S_BET: >2500 m³/g; V_Total (cm³/g) ≥ 1.5; V_Micro (cm³/g) ≥ 0.5) NPCMs. Moreover, it was observed that a narrow pore size distribution (0.5-2.0 nm) yields excellent results in the remediation of noxious contaminants. Further, chemical activating agents such as NaOH, KOH, ZnCl₂, and H₃PO₄ were compared. It was observed that activating agents KОН, H₃PO₄, and ZnCl₂ were generally used and played a significant role in the possible large-scale production and commercialization of NPCMs. Thus, it can be interpreted that with a well-planned strategy for the synthesis, NPCMs with a "tuned" porosity for a specific application, in particular, microporosity for the accumulation and adsorption of energetically important gases (CO₂, CH₄, H₂), micro-mesoporosity and mesoporosity for high adsorption capacity for towards metal ions and a large number of dyes, respectively.

A review on the treatment of dyes in printing and dyeing wastewater by plant biomass carbon

Printing and dyeing wastewater (PDW) has characteristics of large amount of water, elevated content of residual dyes, poor biodegradability, high alkalinity and large change of water quality, making its treatment difficult. Development of efficient and economic PDW treatment technology has gained considerable interest in the field of environmental protection. Use of plant biomass carbon (PBC) for the adsorption of dyes is a feasible and economical technology. This review summarizes current literature discussing the preparation method and physicochemical characteristics of PBC prepared from different plant species, the effect of PBC on the removal of dyes, influencing factors affecting the removal, and relevant adsorption models. The shortcomings of current research and the direction of future research are also pointed out in the review.

Effective mitigation of single-component and mixed textile dyes from aqueous media using recyclable graphene-based nanocomposite

The present study reported the synthesis and utilization of a graphene-based hybrid nanocomposite (MnFe₂O₄/G) to mitigate several synthetic dyes, including methylene blue, malachite green, crystal violet, and Rhodamine B. This adsorbent was structurally analyzed by several physicochemical techniques such as X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, Raman spectroscopy, N₂ adsorption-desorption isotherm measurement, point of zero charge, and Boehm titrations. BET surface area of MnFe₂O₄/G was measured at 382.98 m²/g, which was substantially higher than that of MnFe₂O₄. MnFe₂O₄/G possessed diverse surface chemistry properties with the presence of many functional groups such as carboxylic acid, phenolic, lactone, and basic groups. MnFe₂O₄/G was used to remove synthetic dyes in the aqueous media. The effect of many factors, e.g., concentration (5-50 mg/L), pH (4-10), dose (5-20 mg), and temperature (25-45 °C) on adsorption performance of MnFe₂O₄/G was conducted. Kinetic, isotherm, intraparticle, and thermodynamic models were adopted for investigating adsorption phenomenon of dyes on MnFe₂O₄/G. The maximum adsorption capacity of dyes over MnFe₂O₄/G was found as Rhodamine B (67.8 mg/g) < crystal violet (81.3 mg/g) < methylene blue (137.7 mg/g) < malachite green (394.5 mg/g). Some tests were performed to remove mixed dyes, and mixed dyes in the presence of antibiotics with total efficiencies of 65.8-87.9% after 120 min. Moreover, the major role of π-π stacking interaction was clarified to gain insight into the adsorption mechanism. MnFe₂O₄/G could recycle up to 4 cycles, which may be beneficial for further practical water treatment.

Sorbent Properties of Orange Peel-Based Biochar for Different Pollutants in Water

Efficient and reasonable utilization of waste biomass resources can not only avoid serious waste of material resources, but also solve the problem of environmental pollution. Therefore, the development of efficient and environmentally friendly waste biomass carbonization technology has important practical significance. Here, the activated carbon from orange peel (OAC) is prepared by potassium hydroxide (KOH) activation combined with high-temperature carbonization. The adsorption effects of OAC on three different pollutant aqueous solutions, methylene blue (MB), tetracycline (TC), and fluorescein sodium (NaFL), are examined. The OAC absorbent has excellent adsorption capacity for MB, TC, and NaFL pollutants of 10 mg L−1, with adsorption rates of 99.17%, 73.5%, and 94.24%, respectively. This study provides a new idea for turning waste biomass into treasure and eliminating the hidden danger of environmental pollution.

Recent Developments in the Application of Bio-Waste-Derived Adsorbents for the Removal of Methylene Blue from Wastewater: A Review

Over the last few years, various industries have released wastewater containing high concentrations of dyes straight into the ecological system, which has become a major environmental problem (i.e., soil, groundwater, surface water pollution, etc.). The rapid growth of textile industries has created an alarming situation in which further deterioration to the environment has been caused due to substances being left in treated wastewater, including dyes. The application of activated carbon has recently been demonstrated to be a highly efficient technology in terms of removing methylene blue (MB) from wastewater. Agricultural waste, as well as animal-based and wood products, are excellent sources of bio-waste for MB remediation since they are extremely efficient, have high sorption capacities, and are renewable sources. Despite the fact that commercial activated carbon is a favored adsorbent for dye elimination, its extensive application is restricted because of its comparatively high cost, which has prompted researchers to investigate alternative sources of adsorbents that are non-conventional and more economical. The goal of this review article was to critically evaluate the accessible information on the characteristics of bio-waste-derived adsorbents for MB's removal, as well as related parameters influencing the performance of this process. The review also highlighted the processing methods developed in previous studies. Regeneration processes, economic challenges, and the valorization of post-sorption materials were also discussed. This review is beneficial in terms of understanding recent advances in the status of biowaste-derived adsorbents, highlighting the accelerating need for the development of low-cost adsorbents and functioning as a precursor for large-scale system optimization.

Porous ZnCl2-Activated Carbon from Shaddock Peel: Methylene Blue Adsorption Behavior

It is of great interest and importance to resource utilization of waste biomass to produce porous carbon for environmental treatments. Pore structure and properties of the obtained carbon mainly relate to carbonization conditions and biomass types. In this work, a series of porous, biomass-activated carbons (AC) were prepared using shaddock peel, with ZnCl2 as a pore-forming agent. The effect of carbonization temperature and the mass ratio between ZnCl2 and shaddock peel were thoroughly investigated. The material composition, surface chemical properties, and surface structures of samples were carefully characterized. The specific surface area and adsorption capacity to methylene blue (MB) of adsorbents were changed with the carbonization temperature and the mass ratios between ZnCl2 and shaddock peel; when the temperature was at 1000 °C and the mass ratio was equal to 2:1, the resulting adsorbent had the largest specific surface area of 2398.74 m2/g and average pore size of 3.04 nm, which showed the highest adsorption capacity to MB to be 869.57 mg/g. The adsorption processes of biomass AC adsorbent matched the pseudo-second-order kinetic model and Langmuir isotherm model. This efficient and environmentally friendly biomass AC adsorbent from shaddock peel, activated by ZnCl2, is a promising candidate for the treatment of water pollution.

Synthesis of Porous Material from Coal Gasification Fine Slag Residual Carbon and Its Application in Removal of Methylene Blue

A large amount of coal gasification slag is produced every year in China. However, most of the current disposal is into landfills, which causes serious harm to the environment. In this research, coal gasification fine slag residual carbon porous material (GFSA) was prepared using gasification fine slag foam flotation obtained carbon residue (GFSF) as raw material and an adsorbent to carry out an adsorption test on waste liquid containing methylene blue (MB). The effects of activation parameters (GFSF/KOH ratio mass ratio, activation temperature, and activation time) on the cation exchange capacity (CEC) of GFSA were investigated. The total specific surface area and pore volume of GSFA with the highest CEC were 574.02 m2/g and 0.467 cm3/g, respectively. The degree of pore formation had an important effect on CEC. The maximum adsorption capacity of GFSA on MB was 19.18 mg/g in the MB adsorption test. The effects of pH, adsorption time, amount of adsorbent, and initial MB concentration on adsorption efficiency were studied. Langmuir isotherm and quasi second-order kinetic model have a good fitting effect on the adsorption isotherm and kinetic model of MB.

The removal of anionic and cationic dyes from an aqueous solution using biomass-based activated carbon

In this study, two biomass-based adsorbents were used as new precursors for optimizing synthesis conditions of a cost-effective powdered activated carbon (PAC). The PAC removed dyes from an aqueous solution using carbonization and activation by KOH, NaOH, and H₂SO₄. The optimum synthesis, activation temperature, time and impregnation ratio, removal rate, and uptake capacity were determined. The optimum PAC was analyzed and characterized using Fourier-transform infrared spectroscopy (FTIR), x-ray diffraction (XRD), a field emission scanning electron microscope (FESEM), Zeta potential, and Raman spectroscopy. Morphological studies showed single-layered planes with highly porous surfaces, especially PAC activated by NaOH and H₂SO₄. The results showed that the experimental data were well-fitted with a pseudo-second-order model. Based on Langmuir isotherm, the maximum adsorption capacity for removing methylene blue (MB) was 769.23 mg g⁻¹ and 458.43 mg g⁻¹ for congo red (CR). Based on the isotherm models, more than one mechanism was involved in the adsorption process, monolayer for the anionic dye and multilayer for the cationic dye. Elovich and intraparticle diffusion kinetic models showed that rubber seed shells (RSS) has higher α values with a greater tendency to adsorb dyes compared to rubber seed (RS). A thermodynamic study showed that both dyes’ adsorption process was spontaneous and exothermic due to the negative values of the enthalpy (ΔH) and Gibbs free energy (ΔG). The change in removal efficiency of adsorbent for regeneration study was observed in the seventh cycles, with a 3% decline in the CR and 2% decline in MB removal performance. This study showed that the presence of functional groups and active sites on the produced adsorbent (hydroxyl, alkoxy, carboxyl, and π − π) contributed to its considerable affinity for adsorption in dye removal. Therefore, the optimum PAC can serve as efficient and cost-effective adsorbents to remove dyes from industrial wastewater.