Molecular level interactions in brushite-aminoacids composites

Injectable Self-Harden Antibiofilm Bioceramic Cement for Minimally Invasive Surgery

There is an urgent demand for antibacterial bone grafts in clinics. Worryingly, the misuse and overuse of antibiotics accelerate the emergence of drug-resistant bacteria. Therefore, this study prepared a novel injectable bioceramic cement without antibiotics (FS-BCS), which showed good antibacterial properties by loading iron and strontium onto a matrix composed of brushite and calcium sulfate. The setting time, injectability, microstructure, antibacterial properties, anti-biofilm properties, and cytocompatibility of the novel bioceramic cement were evaluated thoroughly. The results showed that the material was highly injectable and antiwashout. The antibacterial tests revealed that FS-BCS inhibited the growth of 99.9% E. coli and S. aureus separately in the broth due to the synergistic effect of strontium and iron. Simultaneously, crystal violet and fluorescent staining tests revealed that the material could significantly inhibit the formation of E. coli and S. aureus biofilms. In addition, the co-incorporation of iron and strontium promoted the proliferation and migration of osteoblasts. Therefore, FS-BCS has good application potential in antibiotic-free anti-infection bone grafting using minimally invasive surgery.

Effect of L-Glutamic Acid on the Composition and Morphology of Nanostructured Calcium Phosphate as Biomaterial

Calcium phosphate (CaP) with several chemical compositions and morphologies was prepared by precipitation using aqueous solutions of L-Glutamic acid (H₂G) and calcium hydroxide, both mixed together with an aqueous solution (0.15 M) of phosphoric acid. Plate-shaped dicalcium phosphate dihydrate (brushite) particles were obtained and identified at a lower concentration of the solution of the reactants. The Ca/P ratio deduced by EDS was ~1, as expected. The nanoscale dimension of carbonate apatite and amorphous calcium phosphate, with variable Ca/P ratios, were revealed by X-ray diffraction (XRD) and scanning electron microscopy and energy dispersive X-ray spectroscopy analysis (SEM-EDS). They were characterized in medium and high concentrations of calcium hydroxide (0.15 M and 0.20 M). The equilibria involved in all the reactions in aqueous solution were determined. The thermodynamic calculations showed a decrease in the amount of chelate complexes with an increase in pH, being the opposite of [CaPO₄^-] and [CaHG⁺]. This fluctuation showed an evident influence on the morphology and polymorphism of CaP particles obtained under the present experimental conditions, with potential use as a biomaterial.

Evolution of Biomimetic Approaches for Regenerative and Restorative Dentistry

Biomimetics refers to human-made processes, substances, systems, or devices that imitate nature. The art and science of designing and building biomimetic apparatus are called biomimetics. This method can be widely used in dentistry to restore the structure and function of normal tooth structure. Traditional approaches to treating damaged and decayed teeth require more aggressive preparation to place a "strong," stiff restoration. The emphasis was made on the strength of the restoration as well as its function and mechanical properties, despite several disadvantages like tooth fracture, making future treatment more difficult and invasive. This review paper will seek to provide a clear explanation of its scope, different fields of biomimetic dentistry, and materials used in biomimetics that improve the strength of the tooth.

Development of a Hybrid Biomimetic Enamel-Biocomposite Interface and a Study of Its Molecular Features Using Synchrotron Submicron ATR-FTIR Microspectroscopy and Multivariate Analysis Techniques

Using a biomimetic strategy and bioinspired materials, our work proposed a new technological approach to create a hybrid transitional layer between enamel and dental biocomposite. For this purpose, an amino acid booster conditioner based on a set of polar amino acids (lysine, arginine, hyaluronic acid), calcium alkali, and a modified adhesive based on BisGMA and nanocrystalline carbonate-substituted hydroxyapatite are used during dental enamel restoration. The molecular properties of the hybrid interface formed using the proposed strategy were understood using methods of multivariate statistical analysis of spectral information collected using the technique of synchrotron infrared microspectroscopy. The results obtained indicate the possibility of forming a bonding that mimics the properties of natural tissue with controlled molecular properties in the hybrid layer. The diffusion of the amino acid booster conditioner component, the calcium alkali, and the modified adhesive with nanocrystalline carbonate-substituted hydroxyapatite in the hybrid interface region creates a structure that should stabilize the reconstituted crystalline enamel layer. The developed technology can form the basis for an individualized, personalized approach to dental enamel restorations.

The Molecular and Mechanical Characteristics of Biomimetic Composite Dental Materials Composed of Nanocrystalline Hydroxyapatite and Light-Cured Adhesive

The application of biomimetic strategies and nanotechnologies (nanodentology) has led to numerous innovations and provided a considerable impetus by creating a new class of modern adhesion restoration materials, including different nanofillers. An analysis of the molecular properties of biomimetic adhesives was performed in this work to find the optimal composition that provides high polymerisation and mechanical hardness. Nanocrystalline carbonate-substituted calcium hydroxyapatite (nano-cHAp) was used as the filler of the light-cured adhesive Bis-GMA (bisphenol A-glycidyl methacrylate). The characteristics of this substance correspond to the apatite of human enamel and dentin, as well as to the biogenic source of calcium: avian eggshells. The introduction and distribution of nano-cHAp fillers in the adhesive matrix resulted in changes in chemical bonding, which were observed using Fourier transform infrared (FTIR) spectroscopy. As a result of the chemical bonding, the Vickers hardness (VH) and the degree of conversion under photopolymerisation of the nano-cHAp/Bis-GMA adhesive increased for the specified concentration of nanofiller. This result could contribute to the application of the developed biomimetic adhesives and the clinical success of restorations.

Investigation of the Effect of Nanocrystalline Calcium Carbonate-Substituted Hydroxyapatite and L-Lysine and L-Arginine Surface Interactions on the Molecular Properties of Dental Biomimetic Composites

Differences in the surface interactions of non-stoichiometric nanocrystalline B-type carbonate-substituted hydroxyapatite (n-cHAp) with the amino acids L-Lysine hydrochloride (L-LysHCl) and L-Arginine hydrochloride (L-ArgHCl) in acidic and alkaline media were determined using structural and spectroscopic analysis methods. The obtained data confirm that hydroxyapatite synthesized using our technique, which was used to develop the n-cHAp/L-LysHCl and n-cHAp/L-ArgHCl composites, is nanocrystalline. Studies of molecular composition of the samples by Fourier transform infrared spectroscopy under the change in the charge state of L-Lysine in environments with different alkalinity are consistent with the results of X-ray diffraction analysis, as evidenced by the redistribution of the modes' intensities in the spectra that is correlated with the side chains, i.e., amide and carboxyl groups, of the amino acid. During the formation of a biomimetic composite containing L-Lysine hydrochloride and n-cHAp, the interaction occurred through bonding of the L-Lysine side chain and the hydroxyl groups of hydroxyapatite, which created an anionic form of L-Lysine at pH ≤ 5. In contrast, in biocomposites based on L-Arginine and n-cHAp, the interaction only slightly depends on pH value, and it proceeds by molecular orientation mechanisms. The X-ray diffraction and infrared spectroscopy results confirm that changes in the molecular composition of n-cHAp/L-ArgHCl biomimetic composites are caused by the electrostatic interaction between the L-ArgHCl molecule and the carbonate-substituted calcium hydroxyapatite. In this case, the bond formation was detected by Fourier transform infrared (FTIR) spectroscopy; the vibrational modes attributed to the main carbon chain and the guanidine group of L-Arginine are shifted during the interaction. The discovered interaction mechanisms between nanocrystalline carbonate-substituted hydroxyapatite that has physicochemical properties characteristic of the apatite in human dental enamel and specific amino acids are important for selecting the formation conditions of biomimetic composites and their integration with the natural dental tissue.

Characterization of Properties, In Vitro and In Vivo Evaluation of Calcium Phosphate/Amino Acid Cements for Treatment of Osteochondral Defects

Novel calcium phosphate cements containing a mixture of four amino acids, glycine, proline, hydroxyproline and either lysine or arginine (CAL, CAK) were characterized and used for treatment of artificial osteochondral defects in knee. It was hypothesized that an enhanced concentration of extracellular collagen amino acids (in complex mixture), in connection with bone cement in defect sites, would support the healing of osteochondral defects with successful formation of hyaline cartilage and subchondral bone. Calcium phosphate cement mixtures were prepared by in situ reaction in a planetary ball mill at aseptic conditions and characterized. It was verified that about 30–60% of amino acids remained adsorbed on hydroxyapatite particles in cements and the addition of amino acids caused around 60% reduction in compressive strength and refinement of hydroxyapatite particles in their microstructure. The significant over-expression of osteogenic genes after the culture of osteoblasts was demonstrated in the cement extracts containing lysine and compared with other cements. The cement pastes were inserted into artificial osteochondral defects in the medial femoral condyle of pigs and, after 3 months post-surgery, tissues were analyzed macroscopically, histologically, immunohistochemically using MRI and X-ray methods. Analysis clearly showed the excellent healing process of artificial osteochondral defects in pigs after treatment with CAL and CAK cements without any inflammation, as well as formation of subchondral bone and hyaline cartilage morphologically and structurally identical to the original tissues. Good integration of the hyaline neocartilage with the surrounding tissue, as well as perfect interconnection between the neocartilage and new subchondral bone tissue, was demonstrated. Tissues were stable after 12 months’ healing.

Cu-loaded Brushite bone cements with good antibacterial activity and operability

Bone defect-related surgical procedures are traumatic processes carrying potential inflammation and infection risks in the clinic, which are associated with prolonged antibiotic therapy that promotes bacterial antibiotic-resistance. In the present study, Cu-loaded brushite bone cements were designed, and the properties of the bone cements were evaluated. The setting time of the cement was prolonged from 12 to 50 min as the copper content increased. All cements were anti-washout, and the injectable coefficient of the cements was approximately 88%. Scanning electron microscopy results revealed that the crystal grains grew larger and thicker as the copper content in the cement increased, and brushite was determined to be the dominant crystalline phase for all the cements. However, a small amount of newly formed calcium copper phosphate was observed in the cement. Simultaneously, band shifts were observed in the Fourier transform infrared spectroscopy results at a Cu content of 5%. Moreover, the addition of Cu improved the compressive strength of brushite cements, and all cements were degradable. Furthermore, the Cu-loaded brushite bone cements performed well in inhibiting the growth and proliferation of Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa, and the diameter of the inhibition zone increased with increasing copper content. The study revealed that the Cu-loaded brushite bone cements possessed good cellular affinity to mouse bone marrow stem cells when a lower dose of copper was added in vitro. These results support the great potential of injectable antibacterial brushite bone cement specifically for bone tissue defect-related repair and regeneration.