In vitro biocompatibility of new bioactive lithia-silica glass-ceramics

Sol-gel synthesis of lithium doped mesoporous bioactive glass nanoparticles and tricalcium silicate for restorative dentistry: Comparative investigation of physico-chemical structure, antibacterial susceptibility and biocompatibility

Introduction: The sol-gel method for production of mesoporous bioactive glass nanoparticles (MBGNs) has been adapted to synthesize tricalcium silicate (TCS) particles which, when formulated with other additives, form the gold standard for dentine-pulp complex regeneration. Comparison of TCS and MBGNs obtained by sol-gel method is critical considering the results of the first ever clinical trials of sol-gel BAG as pulpotomy materials in children. Moreover, although lithium (Li) based glass ceramics have been long used as dental prostheses materials, doping of Li ion into MBGNs for targeted dental applications is yet to be investigated. The fact that lithium chloride benefits pulp regeneration in vitro also makes this a worthwhile undertaking. Therefore, this study aimed to synthesize TCS and MBGNs doped with Li by sol-gel method, and perform comparative characterizations of the obtained particles.

Methods: TCS particles and MBGNs containing 0%, 5%, 10% and 20% Li were synthesized and particle morphology and chemical structure determined. Powder concentrations of 15mg/10 mL were incubated in artificial saliva (AS), Hank’s balanced saline solution (HBSS) and simulated body fluid (SBF), at 37°C for 28 days and pH evolution and apatite formation, monitored. Bactericidal effects against S. aureus and E. coli, as well as possible cytotoxicity against MG63 cells were also evaluated through turbidity measurements.

Results: MBGNs were confirmed to be mesoporous spheres ranging in size from 123 nm to 194 nm, while TCS formed irregular nano-structured agglomerates whose size was generally larger and variable. From ICP-OES data, extremely low Li ion incorporation into MBGNs was detected. All particles had an alkalinizing effect on all immersion media, but TCS elevated pH the most. SBF resulted in apatite formation for all particle types as early as 3 days, but TCS appears to be the only particle to form apatite in AS at a similar period. Although all particles had an effect on both bacteria, this was pronounced for undoped MBGNs. Whereas all particles are biocompatible, MBGNs showed better antimicrobial properties while TCS particles were associated with greater bioactivity.

Conclusion: Synergizing these effects in dental biomaterials may be a worthwhile undertaking and realistic data on bioactive compounds targeting dental application may be obtained by varying the immersion media.

The Biological Activity of Fragmented Computer-Aided Design/Manufacturing Dental Materials before and after Exposure to Acidic Environment

Three ceramic and composite computer-aided design/computer-aided manufacturing (CAD/CAM) materials from different manufacturers (Cerasmart (CS)-nanoceramic resin; Straumann Nice (SN)-glass ceramic and Tetric CAD (TC)-composite resin) were tested to investigate the biocompatibility and sustainability on human fibroblasts and keratinocytes cells. Each type of CAD/CAM blocks restorative materials with fine and rough surfaces was exposed to an acidic environment for one month. After that, various powders were obtained by milling. In parallel, powders were also prepared from each restorative material, which were not exposed to the acidic environment. The cytotoxic effects were investigated by means of MTT and LDH assays, as well as nitric oxide production on two human normal cell lines, namely, fibroblasts (BJ) and keratinocytes (HaCaT). In addition, the degree of adhesion of fibroblast cells to each CAD/CAM material was evaluated by scanning electron microscopy (SEM). The results showed that the two samples that were exposed to an acidic environment (CS and SN) induced a reduction of mitochondrial activity and plasma membrane damage as regards the fibroblast cells. A similar effect was observed in TC_fine-exposed material, which seemed to induce necrosis at the tested concentration of 1 mg/mL. No oxidative stress was observed in fibroblasts and keratinocytes treated with the CAD/CAM materials. Regarding the adhesion degree, it was found that the fibroblasts adhere to all the occlusal veneers tested, with the mention that the CS and SN materials have a weaker adhesion with fewer cytoplasmic extensions than TC material. With all of this considered, the CAD/CAM restorative materials tested are biocompatible and represent support for the attachment and dispersion of cells.

"Gingival Soft Tissue Integrative" Lithium Disilicate Glass-Ceramics with High Mechanical Properties and Sustained-Release Lithium Ions

Due to their good mechanical performances and high biocompatibility, all-ceramic materials are widely applied in clinics, especially in orthopedic and dental areas. However, the "hard" property negatively affects its integration with "soft" tissue, which greatly limits its application in soft tissue-related areas. For example, dental implant all-ceramic abutments should be well integrated with the surrounding gingival soft tissue to prevent the invasion of bacteria. Mimicking the gingival soft tissue and dentine integration progress, we applied the modified ion-exchange technology to "activate" the biological capacity of lithium disilicate glass-ceramics, via introducing OH^- to weaken the stability of Si-O bonds and release lithium ions to promote multi-reparative functions of gingival fibroblasts. The underlying mechanism was found to be closely related to the activation of mitochondrial activity and oxidative phosphorylation. In addition, during the ion-exchange process, the larger radius sodium ions (Na⁺) replaced the smaller radius lithium ions (Li⁺), so that the residual compressive stress was applied to the glass-ceramics surface to counteract the tensile stress, thus improving the mechanical properties. This successful case in simultaneous improvement of mechanical properties and biological activities proves the feasibility of developing "soft tissue integrative" all-ceramic materials with high mechanical properties. It proposes a new strategy to develop advanced bioactive and high strength all-ceramic materials by modified ion-exchange, which can pave the way for the extended applications of such all-ceramic materials in soft tissue-related areas.

ZnO nanoparticle modified chitosan/borosilicate bioglass composite scaffold for inhibiting bacterial infection and promoting bone regeneration

The treatment of implant-associated bone infection remains a significant clinical challenge. However, bone scaffolds with antimicrobial activity and osteoinductive properties can prevent these infections and improve clinical outcomes. In this study, borosilicate bioglass and chitosan composite scaffolds were prepared, and then the surface was modified with nano-zinc oxide. In vitro and in vivo experiments showed that the chitosan/borosilicate bioglass scaffolds have good degradation and osteogenic properties, while the oxidized Zinc scaffolds have better antibacterial properties.

Li-Doped Bioactive Ceramics: Promising Biomaterials for Tissue Engineering and Regenerative Medicine

Lithium (Li) is a metal with critical therapeutic properties ranging from the treatment of bipolar depression to antibacterial, anticancer, antiviral and pro-regenerative effects. This element can be incorporated into the structure of various biomaterials through the inclusion of Li chloride/carbonate into polymeric matrices or being doped in bioceramics. The biocompatibility and multifunctionality of Li-doped bioceramics present many opportunities for biomedical researchers and clinicians. Li-doped bioceramics (capable of immunomodulation) have been used extensively for bone and tooth regeneration, and they have great potential for cartilage/nerve regeneration, osteochondral repair, and wound healing. The synergistic effect of Li in combination with other anticancer drugs as well as the anticancer properties of Li underline the rationale that bioceramics doped with Li may be impactful in cancer treatments. The role of Li in autophagy may explain its impact in regenerative, antiviral, and anticancer research. The combination of Li-doped bioceramics with polymers can provide new biomaterials with suitable flexibility, especially as bio-ink used in 3D printing for clinical applications of tissue engineering. Such Li-doped biomaterials have significant clinical potential in the foreseeable future.

Effect of the surface finish on the mechanical properties and cellular adhesion in (Ce,Y)-TZP/Al2O3 ceramic composites for denture implants

Ceramic composites based on (Ce, Y)-TZP/Al₂O₃ system have great potential for applications as dental implants due to their unusually great balance between good mechanical properties and resistance to hydrothermal degradation. Surface roughness plays an important role in controlling these properties, but few studies have investigated the relationship between cytocompatibility and surface roughness, at levels considered moderate and low, comparable to titanium implants. In this work, bending strength, hydrothermal degradation and biological evaluation of a ceramic composite based on (Ce,Y)-TZP/Al₂O₃ system were investigated as a function of surface roughness. Compacted samples were sintered at 1500 °C - 2h and then submitted to different surface treatments: Group 1 composed of samples with smooth surfaces, Group 2 and Group 3 composed of rough surfaces (grinded with 15 μm or 45 μm diamond sandpaper, respectively. Samples were characterized by X-ray diffraction, scanning electron microscopy, contact angle and optical profilometry and then subjected to hydrothermal degradation tests in autoclave (134 °C - 2 bar) using artificial saliva. The Piston-on-three-balls (P-3B) testing was used to determine flexural strength. To assess indirect cytotoxicity, samples were immersed in the culture medium for NIH-3T3 cells for 72 h. Furthermore, cell adhesion and proliferation were investigated using MG63 cells (human osteosarcoma) after 3, 7, 14, and 21 days of culture. Cytotoxicity, adhesion, and cell proliferation were examined by the Methyl Tetrazolium salt (MTS) and Alizarin Red, using a confocal laser microscope. The results indicated that the materials have high resistance to degradation. Furthermore, the (Ce,Y)-TZP/Al₂O₃ composites are not cytotoxic. The flexural strength of the composites was 913 ± 103 MPa in samples presenting original (smooth) surface, however, a reduction in the order of 17% was observed in samples containing rough surfaces. The rougher samples show the best cellular adhesion and proliferation, leading to the formation of a mineralized matrix after 21 days. These results clearly suggest that the new (Ce,Y)-TZP/Al₂O₃ brand is strong and highly biocompatible and warrants further study.

Effect of Li+/Na+ exchange on mechanical behavior and biological activity of lithium disilicate glass-ceramic

Lithium disilicate (LD) glass-ceramics with a stoichiometric composition were ion-exchanged in pure NaNO₃ or mixed NaNO₃ + KNO₃ molten salt baths below the glass transition temperature (T_g). The microstructures, surface morphologies, mechanical properties and bioactivities of the ion-exchanged glass-ceramics were studied in detail. It was found that the strength and toughness of LD glass-ceramic could be enhanced from 175 MPa to 0.96 MPa m^1/2 before ion-exchange to 546 MPa and 4.31 MPa m^1/2 respectively under a lowered ion-exchange temperature because the less stress relaxation. In addition, a gradient of Na⁺ rich layer in the surface of glass-ceramic was induced by Li⁺/Na⁺ exchange, which could be beneficial to the formation of HA (Hydroxyapatite) with nano-size porous after soaking in SBF (Simulated Body Fluid) solution and exhibited better bioactivity compared with the original LD glass-ceramic. The results might provide a reference for the strengthening and biological activation of LD glass-ceramics in bone restoration applications.

Optimizing the microstructure of a new machinable bioactive glass-ceramic

OBJECTIVES

This study aimed to optimize the crystallization process and the microstructure of a new bioactive glass-ceramic (GC) previously developed by our research group to obtain machinable glass-ceramics.

METHODS

Differential scanning calorimetry (DSC) analyses were conducted to explore the characteristic temperatures and construct a semi-quantitative nucleation curve. The GC specimens were characterized by X-ray diffraction (XRD) and Rietveld refinement. Their brittleness index (B) and machinability were characterized and compared with IPS e.max-CAD®. Their Young's modulus, fracture toughness, and hardness were assessed.

RESULTS

We found that the maximum crystal nucleation rate temperature of this GC is ~470 °C. Treatments were designed based on the 1st DSC peak onset (570 °C), 1st peak offset (650 °C), and 2nd peak offset (705 °C) crystallization temperatures of lithium metasilicate (LS, LiSi₂O₃) and lithium disilicate (LS2, Li₂Si₂O₅). Rietveld refinement indicated an increase in LS2 and a reduction in LS and amorphous phase for increased temperatures and longer treatment times. Their B values indicate good machinability compared with that of the control group based on statistical analyses. As expected, lower levels of LS2 increase the machinability regardless of the rotation speed adopted, leading to a greater depth of cut and reduced Edge Chipping Damage Depth (ECDD).

CONCLUSION

This bioactive GC with optimized microstructure presents high machinability. For treatment temperatures above 570 °C, the number of elongated LS2 crystals increases and decreases the amorphous phase content, which reduce the machinability of the GC, and should therefore be avoided. The best results were obtained using heat treatment at 570 °C, which produces LS crystals embedded in a glassy matrix (67%) with small contents of secondary phases.

Dissolution, bioactivity behavior, and cytotoxicity of 19.58Li2 O·11.10ZrO2 ·69.32SiO2 glass-ceramic

Glass and bioactive glass-ceramic can be used in several applications. In bone growth where good bone/biomaterial adhesion was required, bioactive coatings for implants can improve bone formation. The glass and glass-ceramics of the LZS (Li₂ O-ZrO₂ -SiO₂ ) system are very interesting because of their mechanical, electrical, and thermal properties. Very recently, their biological response in contact with human osteoblast has been evaluated. However, despite several initiatives, there are still no studies that systematically assess this system's bioactivity, dissolution, and cytotoxicity in vitro. This work aims to investigate the dissolution, bioactivity behavior, and cytotoxicity of LZS glass-ceramic. LZS glass-ceramics were produced from SiO₂ , Li₂ CO_3, and ZrSiO₄ by melting followed by quenching. The obtained glass frits were milled and uniaxially pressed and heat-treated at 800 and 900°C and submitted to physical-chemical, structural and mechanical characterization. Their dissolution behavior was studied in Tris-HCl, while bioactivity was performed in simulated solution body fluid (SBF). The cytotoxicity test was performed using glass-ceramic in direct contact with mesenchymal stem/stromal cells (SC) isolated from human exfoliated deciduous teeth. Structural and microstructural analyzes confirmed bioactivity. The results show that it was possible to produce bioactive glass-ceramic from LZS, proven by the formation of new calcium phosphate structures such as hydroxyapatite on the surface of the samples after exposure to SBF. The SC viability test performed indicated that the materials were not cytotoxic at 0.25, 0.5, and 1.0 mg/ml. The glass-ceramic system under study is very promising for a medicinal application that requires bioactivity and/or biocompatibility for bone regeneration.

Review on Polymer, Ceramic and Composite Materials for CAD/CAM Indirect Restorations in Dentistry-Application, Mechanical Characteristics and Comparison

The aim of this review article is to present various material groups, including ceramics, composites and hybrid materials, currently utilized in the field of CAD/CAM. The described technology is amongst the most important in modern prosthetics. Materials that are applicable in this technique are constantly tested, evaluated and improved. Nowadays, research on dental materials is carried out in order to meet the increasing demand on highly aesthetic and functional indirect restorations. Recent studies present the long-term clinical success of restorations made with the help of both ceramic and composite materials in the CAD/CAM method. However, new materials are developed and introduced that do not have long-term in vivo observations. We can outline a monolithic polymer-infiltrated ceramic network and zirconia teeth support that show promising results to date but require further assessment. The materials will be compared with regard to their mechanical and clinical properties, purpose, advantages and limitations.

Li-doped bioglass® 45S5 for potential treatment of prevalent oral diseases

OBJECTIVES

Despite the excellent properties of both pure bioglasses (BG) and BG doped with therapeutic ions (such as Li) in hard tissue applications, there is not enough information about their role in the remineralization and bacterial-growth in oral diseases. The aim of this contribution is to evaluate the effect of both pure BG and BG doped with 5-wt% of Li (BGLi) on both the remineralization of in vitro demineralized human-teeth and the antimicrobial behavior against strains from caries and periodontitis.

METHODS

Bioglass® 45S5 (BG) and BGLi were synthesized by the sol-gel method. The remineralization tests were carried out using in vitro demineralized enamel teeth and evaluated by Electron Microscopy (SEM) and Vickers micro-hardness (HV). The antimicrobial behavior of the particles was evaluated against S. mutans, A. actinomycetemcomitans, and P. gingivalis, representing pathogens from caries and periodontitis.

RESULTS

Enamel lesion was partially remineralized when both bioglasses (BG and BGLi) were applied on its surface with micro-hardness recoveries around 45 %. They further inhibited the growth of S. mutans and P. gingivalis, at 50 and 200 mg/mL, respectively. BGLi presented a higher toxicity against A. actinomycetemcomitans than BG, with inhibition concentrations of 20 mg/mL and 100 mg/mL, respectively.

CONCLUSIONS

Bioglasses could be used in the treatment of two of the most prevalent oral diseases: caries and periodontitis, promoting the remineralization of the teeth and killing the main pathogens. The presence of Li did not affect the bioactivity of the bioglass and improved the antibacterial effect over A. actinomycetemcomitans strain.

Anti-Bacterial Properties and Biocompatibility of Novel SiC Coating for Dental Ceramic

A 200 nm plasma-enhanced chemical vapor-deposited SiC was used as a coating on dental ceramics to improve anti-bacterial properties for the applications of dental prosthesis. A thin SiO₂ (20 nm) in the same system was deposited first, prior to SiC deposition, to improve the adhesion between SiC to dental ceramic. Silane and methane were the precursors for SiC deposition, and the SiO₂ deposition employed silane and nitrous oxide as the precursors. SiC antimicrobial activity was evaluated on the proliferation of biofilm, Streptococcus sanguinis, and Streptococcus mutans on SiC-coated and uncoated dental ceramics for 24 h. The ceramic coating with SiC exhibited a biofilm coverage of 16.9%, whereas uncoated samples demonstrated a significantly higher biofilm coverage of 91.8%, measured with fluorescence and scanning electron microscopic images. The cytotoxicity of the SiC coating was evaluated using human periodontal ligament fibroblasts (HPdLF) by CellTiter-BlueCell viability assay. After 24 h of HPdLF cultivation, no obvious cytotoxicity was observed on the SiC coating and control group; both sets of samples exhibited similar cell adhesion and proliferation. SiC coating on a ceramic demonstrated antimicrobial activity without inducing cytotoxic effects.

Combined Fluorescence-Based in Vitro Assay for the Simultaneous Detection of Cell Viability and Alkaline Phosphatase Activity during Osteogenic Differentiation of Osteoblast Precursor Cells

Novel bone substitute materials need to be evaluated in terms of their osteogenic differentiation capacity and possible unwanted cytotoxic effects in order to identify promising candidates for the therapy of bone defects. The activity of alkaline phosphatase (ALP) is frequently quantified as an osteogenic marker, while various colorimetric assays, like MTT assay, are used to monitor cell viability. In addition, the DNA or protein content of the samples needs to be quantified for normalization purposes. As this approach is time consuming and often requires the analysis of multiple samples, we aimed to simplify this process and established a protocol for the combined fluorescence-based quantification of ALP activity and cell viability within one single measurement. We demonstrate that the fluorogenic substrate 4-methylumbelliferone-phosphate (4-MUP) and the commonly used para-nitrophenylphosphate (p-NPP) produce comparable and highly correlating results. We further show that fluorescein–diacetate (FDA) can be used to quantify both cell viability and cell number without interfering with the quantification of ALP activity. The measurement of additional normalization parameters is, therefore, unnecessary. Therefore, the presented assay allows for a time-efficient, simple and reliable analysis of both ALP activity and cell viability from one sample and might facilitate experiments evaluating the osteogenic differentiation of osteoblast precursor cells.

Mechanisms of Bioactive Glass on Caries Management: A Review

This review investigates the mechanisms of bioactive glass on the management of dental caries. Four databases (PubMed, Web of Science, EMBASE (via Ovid), Medline (via Ovid)) were systematically searched using broad keywords and terms to identify the literature pertaining to the management of dental caries using "bioactive glass". Titles and abstracts were scrutinized to determine the need for full-text screening. Data were extracted from the included articles regarding the mechanisms of bioactive glass on dental caries management, including the aspect of remineralizing effect on enamel and dentine caries, and antimicrobial effect on cariogenic bacteria. After removal of duplicates, 1992 articles were identified for screening of the titles and abstracts. The full texts of 49 publications were scrutinized and 23 were finally included in this review. Four articles focused on the antimicrobial effect of bioactive glass. Twelve papers discussed the effect of bioactive glass on demineralized enamel, while 9 articles investigated the effect of bioactive glass on demineralized dentine. In conclusion, bioactive glass can remineralize caries and form apatite on the surface of enamel and dentine. In addition, bioactive glass has an antibacterial effect on cariogenic bacteria of which may help to prevent and arrest dental caries.

Lithium Chloride-Releasing 3D Printed Scaffold for Enhanced Cartilage Regeneration

Background

We synthetized a 3D printed poly-ɛ-caprolactone (PCL) scaffold with polydopamine (PDA) coating and lithium chloride (LiCl) deposition for cartilage tissue engineering and analyzed its effect on promoting rabbit bone marrow mesenchymal stem cells (rBMSC) chondrogenesis in vitro.

Material/Methods

PCL scaffolds were prepared by 3D printing with a well-designed CAD digital model, then modified by PDA coating to produce PCL-PDA scaffolds. Finally, LiCl was deposited on the PDA coating to produce PCL-PDA-Li scaffolds. The physicochemical properties, bioactivity, and biocompatibility of PCL-PDA-Li scaffolds were accessed by comparing them with PCL scaffolds and PCL-PDA scaffolds.

Results

3D PCL scaffolds exhibited excellent mechanical integrity as designed. PDA coating and LiCl deposition improved surface hydrophilicity without sacrificing mechanical strength. Li⁺ release was durable and ion concentration did not reach the cytotoxicity level. This in vitro study showed that, compared to PCL scaffolds, PCL-PDA and PCL-PDA-Li scaffolds significantly increased glycosaminoglycan (GAG) formation and chondrogenic marker gene expression, while PCL-PDA-Li scaffolds showed far higher rBMSC viability and chondrogenesis.

Conclusions

3D printed PCL-PDA-Li scaffolds promoted chondrogenesis in vitro and may provide a good method for lithium administration and be a potential candidate for cartilage tissue engineering.

Stereomicroscopic Evaluation of Marginal Fit of E.Max Press and E.Max Computer-Aided Design and Computer-Assisted Manufacturing Lithium Disilicate Ceramic Crowns: An In vitro Study

Objective:

The purpose of this study was to compare the marginal gap of E-max press, and E.max computer-aided design and computer-assisted manufacturing (CAD-CAM) lithium disilicate (LD) ceramic crowns fabricated by using conventional technique and CAD-CAM technique.

Materials and Methods:

This was an in vitro experimental study carried out in Riyadh Elm University and King Saud University. A marginal gap of 30 LD crowns was evaluated by Stereomicroscopy. A total of 15 pressable LD (IPS E.max Press [Ivoclar Vivadent]) ceramic crowns were fabricated by using conventional lost wax pattern method (Group A). Digital impressions of the prepared dies were scanned and transferred to the milling machine. IPS E.max CAD (IPS E-max, Ivoclar, Amherst, NY, USA) LD blocks in shade Vita A2 were then milled by using DWX-50 machine for CAD-CAM crowns (Group B). Descriptive statistics of mean and standard error of marginal gaps for both groups were recorded and compared by applying Mann–Whitney U-test. All the data were analyzed by using statistical analysis software SPSS version 21.0 (Armonk, NY, USA: IBM Corp).

Results:

The LD crowns prepared by CAD-CAM technology (26.80 ± 3.4 μm) had significantly lower (P < 0.001) marginal gap than the LD pressed crowns (38.8 ± 2.3 μm) fabricated by conventional technique. The marginal gaps between CAD-CAM versus conventional groups exhibited significant differences at (42.68 μm vs. 52.46 μm, U = 51.500, P = 0.011), Mesiobuccal (15.94 μm vs. 30.13 μm, U = 45.500, P = 0.005), distolingual (26.70 μm vs. 43.86 μm, U = 63.500, P = 0.042), and distal (12.38 μm vs 31.45 μm, U = 47.500, P = 0.006).

Conclusions:

Within the limitations of the study, it can be concluded that LD all ceramic crowns fabricated by using CAD-CAM techniques showed lesser marginal gap and better marginal fit compared to the conventional technique.