Silk scaffolds with gradient pore structure and improved cell infiltration performance

Engineering biomimetic scaffolds for bone regeneration: Chitosan/alginate/polyvinyl alcohol-based double-network hydrogels with carbon nanomaterials

In this study, new types of hybrid double-network (DN) hydrogels composed of polyvinyl alcohol (PVA), chitosan (CH), and sodium alginate (SA) are introduced, with the hypothesis that this combination and incorporating multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) will enhance osteogenetic differentiation and the structural and mechanical properties of scaffolds for bone tissue engineering applications. Initially, the impact of varying mass ratios of the PVA/CH/SA mixture on mechanical properties, swelling ratio, and degradability was examined. Based on this investigation, a mass ratio of 4:6:6 was determined to be optimal. At this ratio, the hydrogel demonstrated a Young's modulus of 47.5 ± 5 kPa, a swelling ratio of 680 ± 6 % after 3 h, and a degradation rate of 46.5 ± 5 % after 40 days. In the next phase, following the determination of the optimal mass ratio, CNTs and GNPs were incorporated into the 4:6:6 composite resulting in a significant enhancement in the electrical conductivity and stiffness of the scaffolds. The introduction of CNTs led to a notable increase of 36 % in the viability of MG63 osteoblast cells. Additionally, the inhibition zone test revealed that GNPs and CNTs increased the diameter of the inhibition zone by 49.6 % and 52.6 %, respectively.

3D-bioprinted GelMA/gelatin/amniotic membrane extract (AME) scaffold loaded with keratinocytes, fibroblasts, and endothelial cells for skin tissue engineering

Gelatin-methacryloyl (GelMA) is a highly adaptable biomaterial extensively utilized in skin regeneration applications. However, it is frequently imperative to enhance its physical and biological qualities by including supplementary substances in its composition. The purpose of this study was to fabricate and characterize a bi-layered GelMA-gelatin scaffold using 3D bioprinting. The upper section of the scaffold was encompassed with keratinocytes to simulate the epidermis, while the lower section included fibroblasts and HUVEC cells to mimic the dermis. A further step involved the addition of amniotic membrane extract (AME) to the scaffold in order to promote angiogenesis. The incorporation of gelatin into GelMA was found to enhance its stability and mechanical qualities. While the Alamar blue test demonstrated that a high concentration of GelMA (20%) resulted in a decrease in cell viability, the live/dead cell staining revealed that incorporation of AME increased the quantity of viable HUVECs. Further, gelatin upregulated the expression of KRT10 in keratinocytes and VIM in fibroblasts. Additionally, the histological staining results demonstrated the formation of well-defined skin layers and the creation of extracellular matrix (ECM) in GelMA/gelatin hydrogels during a 14-day culture period. Our study showed that a 3D-bioprinted composite scaffold comprising GelMA, gelatin, and AME can be used to regenerate skin tissues.

Cross-Linking Methods of the Silk Protein Hydrogel in Oral and Craniomaxillofacial Tissue Regeneration

BACKGROUND

Craniomaxillofacial tissue defects are clinical defects involving craniomaxillofacial and oral soft and hard tissues. They are characterized by defect-shaped irregularities, bacterial and inflammatory environments, and the need for functional recovery. Conventional clinical treatments are currently unable to achieve regeneration of high-quality oral craniomaxillofacial tissue. As a natural biomaterial, silk fibroin (SF) has been widely studied in biomedicine and has broad prospects for use in tissue regeneration. Hydrogels made of SF showed excellent water retention, biocompatibility, safety and the ability to combine with other materials.

METHODS

To gain an in-depth understanding of the current development of SF, this article reviews the structure, preparation and application prospects in oral and craniomaxillofacial tissue regenerative medicine. It first briefly introduces the structure of SF and then summarizes the principles, advantages and disadvantages of the different cross-linking methods (physical cross-linking, chemical cross-linking and double network structure) of SF. Finally, the existing research on the use of SF in tissue engineering and the prospects of using SF with different cross-linking methods in oral and craniomaxillofacial tissue regeneration are also discussed.

CONCLUSIONS

This review is intended to show the advantages of SF hydrogels in tissue engineering and provides theoretical support for establishing novel and viable silk protein hydrogels for regeneration.

Physicochemical, structural and biological characterisation of poly(3-hydroxyoctanoate) supplemented with diclofenac acid conjugates - Harnessing the potential in the construction of materials for skin regeneration processes

This study involved creating oligomeric conjugates of 3-hydroxy fatty acids and diclofenac, named Dic-oligo(3HAs). Advanced NMR techniques confirmed no free diclofenac in the mix. We tested diclofenac release under conditions resembling healthy and chronic wound skin. These oligomers were used to make P(3HO) blends, forming patches for drug delivery. Their preparation used the solvent casting/porogen leaching (SCPL) method. The patches' properties like porosity, roughness, and wettability were thoroughly analysed. Antimicrobial assays showed that Dic-oligo(3HAs) exhibited antimicrobial activity against reference (S. aureus, S. epidermis, S. faecalis) and clinical (Staphylococcus spp.) strains. Human keratinocytes (HaCaT) cell line tests, as per ISO 10993-5, showed no toxicity. A clear link between material roughness and HaCaT cell adhesion was found. Deep cell infiltration was verified using DAPI and phalloidin staining, observed under confocal microscopy. SEM also confirmed HaCaT cell growth on these scaffolds. The strong adhesion and proliferation of HaCaT cells on these materials indicate their potential as wound dressing layers. Additionally, the successful diclofenac release tests point to their applicability in treating both normal and chronic wounds.

ICA/SDF-1α/PBMSCs loaded onto alginate and gelatin cross-linked scaffolds promote damaged cartilage repair

A three-dimensional alginate-coated scaffold (GAIS) was constructed in the present study to showcase the multidifferentiation potential of peripheral blood mesenchymal stem cells (PBMSCs) and to investigate the role and mechanism by which Icariin (ICA)/stromal cell-derived factor (SDF-1α)/PBMSCs promote damaged articular repair. In addition, the ability of ICA, in combination with SDF-1α, to promote the migration and proliferation of stem cells was validated through the utilization of CCK-8 and migration experiments. The combination of ICA and SDF-1α inhibited the differentiation of PBMSCs into cartilage, as demonstrated by in vivo experiments and histological staining. Both PCR and western blot experiments showed that GAIS could upregulate the expression of particular genes in chondrocytes. In comparison to scaffolds devoid of alginate (G0), PBMSCs seeded into GAIS scaffolds exhibited a greater rate of proliferation, and the conditioned medium derived from scaffolds containing SDF-1α enhanced the capacity for cell migration. Moreover, after a 12-week treatment period, GAIS, when successfully transplanted into osteochondral defects of mice, was found to promote cartilage regeneration and repair. The findings, therefore, demonstrate that GAIS enhanced the in vitro capabilities of PBMSCs, including proliferation, migration, homing and chondrogenic differentiation. In addition, ICA and SDF-1α effectively collaborated to support cartilage formation in vivo. Thus, the ICA/SDF-1α/PBMSC-loaded biodegradable alginate-gelatin scaffolds showcase considerable potential for use in cartilage repair.

Formation of Three-Dimensional Polysuccinimide Electrospun Fiber Meshes Induced by the Combination of CaCl2 and Humidity

Even though electrospinning is getting more and more attention, the preparation of 3D nanofibrous meshes is still a big challenge that limits the application of electrospun materials, especially in tissue engineering. To overcome this problem, several solutions are introduced but most of them focus on the postprocessing of the electrospun meshes. This paper presents a straightforward novel method that utilizes the joint effect of the addition of CaCl2 and the relative environmental humidity (RH), which can induce the random 3D formation of polysuccinimide (PSI) electrospun fibers with different such as wrinkled or ribbon-like structures. Although the effect of humidity and inorganic salt additives on the micro and macrostructure of electrospun fibers is known, the connection between the two in this manner has never been presented. To investigate the effect, fibers with different PSI and CaCl2 concentrations at different humidity RH levels are prepared, and their microstructure is visualized with high-resolution scanning electron microscopy (SEM). To reveal the nature of the interaction between the polymer and the CaCl2, Fourier-transformed infrared (FTIR), X-ray diffraction (XRD), and thermogravimetry (TGA) measurements are carried out and 3D nanofibrous structures are obtained.

Silk fibroin-derived electrospun materials for biomedical applications: A review

Electrospinning is a versatile technique for fabricating polymeric fibers with diameters ranging from micro- to nanoscale, exhibiting multiple morphologies and arrangements. By combining silk fibroin (SF) with synthetic and/or natural polymers, electrospun materials with outstanding biological, chemical, electrical, physical, mechanical, and optical properties can be achieved, fulfilling the evolving biomedical demands. This review highlights the remarkable versatility of SF-derived electrospun materials, specifically focusing on their application in tissue regeneration (including cartilage, cornea, nerves, blood vessels, bones, and skin), disease treatment (such as cancer and diabetes), and the development of controlled drug delivery systems. Additionally, we explore the potential future trends in utilizing these nanofibrous materials for creating intelligent biomaterials, incorporating biosensors and wearable sensors for monitoring human health, and also discuss the bottlenecks for its widespread use. This comprehensive overview illuminates the significant impact and exciting prospects of SF-derived electrospun materials in advancing biomedical research and applications.

A novel biomimetic nanofibrous cardiac tissue engineering scaffold with adjustable mechanical and electrical properties based on poly(glycerol sebacate) and polyaniline

Biomaterial tissue engineering scaffolds play a critical role in providing mechanical support, promoting cells growth and proliferation. However, due to the insulation and inappropriate stiffness of most biomaterials, there is an unmet need to engineer a biomimetic nanofibrous cardiac tissue engineering scaffold with tailorable mechanical and electrical properties. Here, we demonstrate for the first time the feasibility to generate a novel type of biocompatible fibrous scaffolds by blending elastic poly(glycerol sebacate) (PGS) and conductive polyaniline (PANI) with the help of a nontoxic carrier polymer, poly (vinyl alcohol) (PVA). Aligned and random PGS/PANI scaffolds are successfully obtained after electrospinning, cross-linking, water and ethanol wash. Incorporating of different concentrations of PANI into PGS fibers, the fibrous sheets show enhanced conductivity and slower degradation rates while maintaining the favorable hemocompatibility. The elastic modulus of the PGS/PANI scaffolds is in the range of 0.65-2.18 MPa under wet conditions, which is similar to that of natural myocardium. All of these fibrous mats show good cell viability and were able to promote adhesion and proliferation of H9c2 cells. Furthermore, the in vivo host responses of both random and aligned scaffolds confirm their good biocompatibility. Therefore, these PGS/PANI scaffolds have great potential for cardiac tissue engineering.

Enhanced tissue infiltration and bone regeneration through spatiotemporal delivery of bioactive factors from polyelectrolytes modified biomimetic scaffold

Efficient healing of bone defect is closely associated with the structured and functional characters of tissue engineered scaffolds. However, the development of bone implants with rapid tissue ingrowth and favorable osteoinductive properties remains a challenge. Herein, we fabricated polyelectrolytes modified-biomimetic scaffold with macroporous and nanofibrous structures as well as simultaneous delivery of BMP-2 protein and trace element strontium. The hierarchically structured scaffold incorporated with strontium-substituted hydroxyapatite (SrHA) was coated with polyelectrolyte multilayers of chitosan/gelatin via layer-by-layer assembly technique for BMP-2 immobilization, which endowed the composite scaffold with sequential release of BMP-2 and Sr ions. The integration of SrHA improved the mechanical property of composite scaffold, while the polyelectrolytes modification strongly increased the hydrophilicity and protein binding efficiency. In addition, polyelectrolytes modified-scaffold significantly facilitated cell proliferation in vitro, as well as enhanced tissue infiltration and new microvascular formation in vivo. Furthermore, the dual-factor loaded scaffold significantly enhanced the osteogenic differentiation of bone marrow mesenchymal stem cells. Moreover, both vascularization and new bone formation were significantly increased by the treatment of dual-factor delivery scaffold in the rat calvarial defects model, suggesting a synergistic effect on bone regeneration through spatiotemporal delivery of BMP-2 and Sr ions. Overall, this study demonstrate that the prepared biomimetic scaffold as dual-factor delivery system has great potential for bone regeneration application.

Designing of gradient scaffolds and their applications in tissue regeneration

Gradient scaffolds are isotropic/anisotropic three-dimensional structures with gradual transitions in geometry, density, porosity, stiffness, etc., that mimic the biological extracellular matrix. The gradient structures in biological tissues play a major role in various functional and metabolic activities in the body. The designing of gradients in the scaffold can overcome the current challenges in the clinic compared to conventional scaffolds by exhibiting excellent penetration capacity for nutrients & cells, increased cellular adhesion, cell viability & differentiation, improved mechanical stability, and biocompatibility. In this review, the recent advancements in designing gradient scaffolds with desired biomimetic properties, and their implication in tissue regeneration applications have been briefly explained. Furthermore, the gradients in native tissues such as bone, cartilage, neuron, cardiovascular, skin and their specific utility in tissue regeneration have been discussed in detail. The insights from such advances using gradient-based scaffolds can widen the horizon for using gradient biomaterials in tissue regeneration applications.

Nonmulberry silk fibroin-based biomaterials: Impact on cell behavior regulation and tissue regeneration

Silk fibroin (SF) is a promising biomaterial due to its good biocompatibility, easy availability, and high mechanical properties. Compared with mulberry silk fibroin (MSF), nonmulberry silk fibroin (NSF) isolated from typical nonmulberry silkworm silk exhibits unique arginine-glycine-aspartic acid (RGD) sequences with favorable cell adhesion enhancing effect. This inherent property probably makes the NSF more suitable for cell culture and tissue regeneration-related applications. Accordingly, various types of NSF-based biomaterials, such as particles, films, fiber mats, and 3D scaffolds, are constructed and their application potential in different biomedical fields is extensively investigated. Based on these promising NSF biomaterials, this review firstly makes a systematical comparison between the molecular structure and properties of MSF and typical NSF and highlights the unique properties of NSF. In addition, we summarize the effective fabrication strategies from degummed nonmulberry silk fibers to regenerated NSF-based biomaterials with controllable formats and their recent application progresses in cell behavior regulation and tissue regeneration. Finally, current challenges and future perspectives for the fabrication and application of NSF-based biomaterials are discussed. Related research and perspectives may provide valuable references for designing and modifying effective NSF-based and other natural biomaterials. STATEMENT OF SIGNIFICANCE: There exist many reviews about mulberry silk fibroin (MSF) biomaterials and their biomedical applications, while that about nonmulberry silk fibroin (NSF) biomaterials is scarce. Compared with MSF, NSF exhibits unique arginine-glycine-aspartic acid sequences with promising cell adhesion enhancing effect, which makes NSF more suitable for cell culture and tissue regeneration related applications. Focusing on these advanced NSF biomaterials, this review has systematically compared the structure and properties of MSF and NSF, and emphasized the unique properties of NSF. Following that, the effective construction strategies for NSF-based biomaterials are summarized, and their recent applications in cell behavior regulations and tissue regenerations are highlighted. Furthermore, current challenges and future perspectives for the fabrication and application of NSF-based biomaterials were discussed.

Nanosilicate-Reinforced Silk Fibroin Hydrogel for Endogenous Regeneration of Both Cartilage and Subchondral Bone

Osteochondral defects are characterized by injuries to both cartilage and subchondral bone, which is a result of trauma, inflammation, or inappropriate loading. Due to the unique biological properties of subchondral bone and cartilage, developing a tissue engineering scaffold that can promote dual-lineage regeneration of cartilage and bone simultaneously remains a great challenge. In this study, a microporous nanosilicate-reinforced enzymatically crosslinked silk fibroin (SF) hydrogel is fabricated by introducing montmorillonite (MMT) nanoparticles via intercalation chemistry. In vitro studies show that SF-MMT nanocomposite hydrogel has improved mechanical properties and hydrophilicity, as well as the bioactivities to promote the osteogenic differentiation of bone marrow mesenchymal stem cells and maintain chondrocyte phenotype compared with SF hydrogel. Global proteomic analysis verifies the dual-lineage bioactivities of SF-MMT nanocomposite hydrogel, which are probably regulated by multiple signaling pathways. Furthermore, it is observed that the biophysical interaction of cells and SF-MMT nanocomposite hydrogel is partially mediated by clathrin-mediated endocytosis and its downstream processes. In vivo, the SF-MMT nanocomposite hydrogel effectively promotes osteochondral regeneration as evidenced by macroscopic, micro-CT, and histological evaluation. In conclusion, a functionalized SF-MMT nanocomposite hydrogel is developed with dual-lineage bioactivity for osteochondral regeneration, indicating its potential in osteochondral tissue engineering.

Single unit functionally graded bioresorbable electrospun scaffold for scar-free full-thickness skin wound healing

Full-thickness wounds are difficult to heal spontaneously. Scaffolds, meant for treating full-thickness wounds, should ensure proper tissue regeneration, both structurally and functionally. An ideal scaffold should mimic the physical, mechanical and biochemical properties of natural skin. However, available mono- or bi-layer skin scaffolds lack in the precise architecture and functionality, thus, failing to provide scar-free regeneration of full-thickness skin wounds. These unmet challenges of scar-free skin regeneration have been addressed in the present study for the first time. This research deals with the synthesis of a low-cost, structurally and functionally graded single unit biodegradable polymeric scaffold. The functional gradient in this scaffold was achieved by varying polymer concentration and electrospinning parameters. This gradient in the scaffold provided the required microenvironment for proper functional and structural reconstruction of all the layers of natural skin. The mechanical property of the scaffold matched that of the natural skin. Besides, the degradation kinetics of the scaffold was in coordination with the regeneration time for the full-thickness wound. The porosity and hydrophilicity gradients of the scaffold helped it mimic the in vivo hypodermal, dermal and epidermal microenvironments of the skin, simultaneously. Co-culturing PCS-201 (dermal fibroblasts) and HaCaT (keratinocytes) on the scaffold resulted in successful regeneration through cellular proliferation, differentiation and organization of the skin tissue. The scaffold also displayed better wound healing in vivo, in terms of speedy wound closure and proper tissue regeneration, in comparison to the standard treatment. Altogether, this study successfully established a simple, one-step synthesis process of a functionally graded, bioresorbable scaffold for scar-free, native-like, structural and functional regeneration of full-thickness skin wounds. Due to cost-effectiveness, easy synthesis process and microarchitectural features, the designed scaffold possesses a potential of translation to a good commercial wound healing product.

Bioinspired silk fibroin materials: From silk building blocks extraction and reconstruction to advanced biomedical applications

Silk fibroin has become a promising biomaterial owing to its remarkable mechanical property, biocompatibility, biodegradability, and sufficient supply. However, it is difficult to directly construct materials with other formats except for yarn, fabric and nonwoven based on natural silk. A promising bioinspired strategy is firstly extracting desired building blocks of silk, then reconstructing them into functional regenerated silk fibroin (RSF) materials with controllable formats and structures. This strategy could give it excellent processability and modifiability, thus well meet the diversified needs in biomedical applications. Recently, to engineer RSF materials with properties similar to or beyond the hierarchical structured natural silk, novel extraction and reconstruction strategies have been developed. In this review, we seek to describe varied building blocks of silk at different levels used in biomedical field and their effective extraction and reconstruction strategies. This review also present recent discoveries and research progresses on how these functional RSF biomaterials used in advanced biomedical applications, especially in the fields of cell-material interactions, soft tissue regeneration, and flexible bioelectronic devices. Finally, potential study and application for future opportunities, and current challenges for these bioinspired strategies and corresponding usage were also comprehensively discussed. In this way, it aims to provide valuable references for the design and modification of novel silk biomaterials, and further promote the high-quality-utilization of silk or other biopolymers.

Polylactic acid scaffold with directional porous structure for large-segment bone repair

Biodegradable porous scaffolds with different structure, porosity, and strength play a critical role in the repair and regeneration of defects in bone tissue engineering by changing the proliferation condition for cell. In this study, polylactic acid (PLA) scaffold with directional porous structure is designed and fabricated using the method of ice template and phase inversion for speeding up bone repair by promoting the growth and proliferation of bone cells. The morphology, mechanical properties, hydrophilicity, and wicking properties of PLA scaffolds were characterized by scanning electron microscope, universal testing machine, contact angle tester and wicking rate test, respectively. In vitro biocompatibility has been investigated through measuring cell adhesion, proliferation, and viability on PLA scaffold with directional porous structure. Prepared PLA scaffold was implanted into animals to observe the repair mechanism of large-sized bone defects. This study proposes a novel bioporous scaffold design to induce osteocyte growth at the rat calvaria with a directional pore structure, and the scaffold edges were integrated with the calvaria at week 12, effectively promoting the repair and regeneration of defective bone tissue.

Silk fibroin-based biomaterials for cartilage/osteochondral repair

Osteoarthritis (OA) is a common joint disease with a high disability rate. In addition, OA not only causes great physiological and psychological harm to patients, but also puts great pressure on the social healthcare system. Pathologically, the disintegration of cartilage and the lesions of subchondral bone are related to OA. Currently, tissue engineering, which is expected to overcome the defects of existing treatment methods, had a lot of research in the field of cartilage/osteochondral repair. Silk fibroin (SF), as a natural macromolecular material with good biocompatibility, unique mechanical properties, excellent processability and degradability, holds great potential in the field of tissue engineering. Nowadays, SF had been prepared into various materials to adapt to the demands of cartilage/osteochondral repair. SF-based biomaterials can also be functionally modified to enhance repair performance further. In this review, the preparation methods, types, structures, mechanical properties, and functional modifications of SF-based biomaterials used for cartilage/osteochondral repair are summarized and discussed. We hope that this review will provide a reference for the design and development of SF-based biomaterials in cartilage/osteochondral repair field.

PoreScript: Semi-automated pore size algorithm for scaffold characterization

The scaffold pore size influences many critical physical aspects of tissue engineering, including tissue infiltration, biodegradation rate, and mechanical properties. Manual measurements of pore sizes from scanning electron micrographs using ImageJ/FIJI are commonly used to characterize scaffolds, but these methods are both time-consuming and subject to user bias. Current semi-automated analysis tools are limited by a lack of accessibility or limited sample size in their verification process. The work here describes the development of a new MATLAB algorithm, PoreScript, to address these limitations. The algorithm was verified using three common scaffold fabrication methods (e.g., salt leaching, gas foaming, emulsion templating) with varying pore sizes and shapes to demonstrate the versatility of this new tool. Our results demonstrate that the pore size characterization using PoreScript is comparable to manual pore size measurements. The PoreScript algorithm was further evaluated to determine the effect of user-input and image parameters (relative image magnification, pixel intensity threshold, and pore structure). Overall, this work validates the accuracy of the PoreScript algorithm across several fabrication methods and provides user-guidance for semi-automated image analysis and increased throughput of scaffold characterization.

•

PoreScript is a semi-automated MATLAB algorithm to rapidly and accurately characterize scaffold pore size distribution.

•

PoreScript was validated with multiple polymeric scaffolds of different fabrication methods and pore architectures.

•

Guidance of key input variables provides users with a tool for rapid characterization to accelerate scaffold development.

Design and characterization of an in vivo injectable hydrogel with effervescently generated porosity for regenerative medicine applications

Injectable hydrogels that polymerize directly in vivo hold significant promises in clinical settings to support the repair of damaged or failing tissues. Existing systems that allow cellular and tissue ingrowth after injection are limited because of deficient porosity and lack of oxygen and nutrient diffusion inside the hydrogels. Here is reported for the first time an in vivo injectable hydrogel in which the porosity does not pre-exist but is formed concomitantly with its in situ injection by a controlled effervescent reaction. The hydrogel tailorable crosslinking, through the reaction of polyethylene glycol with lysine dendrimers, allows the mixing and injection of precursor solutions from a dual-chamber syringe while entrapping effervescently generated CO₂ bubbles to form highly interconnected porous networks. The resulting structures allow preserving modular mechanical properties (from 12.7 ± 0.9 to 29.9 ± 1.7 kPa) while being cytocompatible and conducive to swift cellular attachment, proliferation, in-depth infiltration and extracellular matrix deposition. Most importantly, the subcutaneously injected porous hydrogels are biocompatible, undergo tissue remodeling and support extensive neovascularisation, which is of significant advantage for the clinical repair of damaged tissues. Thus, the porosity and injectability of the described effervescent hydrogels, together with their biocompatibility and versatility of mechanical properties, open broad perspectives for various regenerative medicine or material applications, since effervescence could be combined with a variety of other systems of swift crosslinking. STATEMENT OF SIGNIFICANCE: A major challenge in hydrogel design is the synthesis of injectable formulations allowing easy handling and dispensing in the site of interest. However, the lack of adequate porosity inside hydrogels prevent cellular entry and, therefore, vascularization and tissue ingrowth, limiting the regenerative potential of a vast majority of injectable hydrogels. We describe here the development of an acellular hydrogel that can be injected directly in situ while allowing the simultaneous formation of porosity. Such hydrogel would facilitate handling through injection while providing a porous structure supporting vascularization and tissue ingrowth.

Fabrication and characterization of an acellular annulus fibrosus scaffold with aligned porous construct for tissue engineering

Scaffolds mimicking the native annulus fibrosus (AF) extracellular matrix (ECM) structure are crucial to guide the seeding cells to regenerate aligned tissue, while fabricating such a scaffold by synthetic material is challengeable. Native acellular scaffolds derived from AF tissue certainly possess the advantages of natural structure and composition. Based on previous studies, we modified decellularization procedure and especially compared two drying methods, including gradient dehydration and freeze-drying. The decellularization process can effectively remove the host cells and antigens such as α-Gal, while maintaining the original ECM including GAG and collagen I. Compared with gradient dehydration, freeze-drying not only rendered the decellularized scaffold in dry state for storage but also gave the scaffold more aligned porous structure and hydrophilicity. And, the acellular porous scaffold manifested better capacity of supporting cell ingrowth when seeded human bone marrow mesenchymal stem cells (hBMSCs) or implanted in vivo. Furthermore, this optimized freeze-dried scaffold showed similar mechanical elastic modulus as native AF and demonstrated rare inflammatory granuloma and immune rejection as observed in HE staining and immunohistochemistry staining (IHC) of CD8 and MAC387 epitopes when implanted subcutaneously in vivo. To sum up, through our decellularization and freeze-drying procedure, an aligned porous three-dimensional scaffold derived from the natural AF ECM was successfully fabricated with good retention of ECM components and benign biocompatibility. It will be a promising scaffold for AF tissue engineering.

Ice Templating Soft Matter: Fundamental Principles and Fabrication Approaches to Tailor Pore Structure and Morphology and Their Biomedical Applications

Porous scaffolds are widely used in biomedical applications where pore size and morphology influence a range of biological processes, including mass transfer of solutes, cellular interactions and organization, immune responses, and tissue vascularization, as well as drug delivery from biomaterials. Ice templating, one of the most widely utilized techniques for the fabrication of porous materials, allows control over pore morphology by controlling ice formation in a suspension of solutes. By fine-tuning freezing and solute parameters, ice templating can be used to incorporate pores with tunable morphological features into a wide range of materials using a simple, accessible, and scalable process. While soft matter is widely ice templated for biomedical applications and includes commercial and clinical products, the principles underpinning its ice templating are not reviewed as well as their inorganic counterparts. This review describes and critically evaluates fundamental principles, fabrication and characterization approaches, and biomedical applications of ice templating in polymer-based biomaterials. It describes the utility of porous scaffolds in biomedical applications, highlighting biological mechanisms impacted by pore features, outlines the physical and thermodynamic mechanisms underpinning ice templating, describes common fabrication setups, critically evaluates complexities of ice templating specific to polymers, and discusses future directions in this field.

Engineering Polysaccharides for Tissue Repair and Regeneration

The success of repair or regeneration depends greatly on the architecture of 3D scaffolds that finely mimic natural extracellular matrix to support cell growth and assembly. Polysaccharides have excellent biocompatibility with intrinsic biological cues and they have been extensively investigated as scaffolds for tissue engineering and regenerative medicine (TERM). The physical and biochemical structures of natural polysaccharides, however, can barely meet all the requirements of tissue-engineered scaffolds. To take advantage of their inherent properties, many innovative approaches including chemical, physical, or joint modifications have been employed to improve their properties. Recent advancement in molecular and material building technology facilitates the fabrication of advanced 3D structures with desirable properties. This review focuses on the latest progress of polysaccharide-based scaffolds for TERM, especially those that construct advanced architectures for tissue regeneration.

Osteochondral Tissue Engineering: The Potential of Electrospinning and Additive Manufacturing

The socioeconomic impact of osteochondral (OC) damage has been increasing steadily over time in the global population, and the promise of tissue engineering in generating biomimetic tissues replicating the physiological OC environment and architecture has been falling short of its projected potential. The most recent advances in OC tissue engineering are summarised in this work, with a focus on electrospun and 3D printed biomaterials combined with stem cells and biochemical stimuli, to identify what is causing this pitfall between the bench and the patients' bedside. Even though significant progress has been achieved in electrospinning, 3D-(bio)printing, and induced pluripotent stem cell (iPSC) technologies, it is still challenging to artificially emulate the OC interface and achieve complete regeneration of bone and cartilage tissues. Their intricate architecture and the need for tight spatiotemporal control of cellular and biochemical cues hinder the attainment of long-term functional integration of tissue-engineered constructs. Moreover, this complexity and the high variability in experimental conditions used in different studies undermine the scalability and reproducibility of prospective regenerative medicine solutions. It is clear that further development of standardised, integrative, and economically viable methods regarding scaffold production, cell selection, and additional biochemical and biomechanical stimulation is likely to be the key to accelerate the clinical translation and fill the gap in OC treatment.

Preparation and biological properties of silk fibroin/nano-hydroxyapatite/hyaluronic acid composite scaffold

In this study, the silk fibroin/nano-hydroxyapatite/hyaluronic acid (SF/nHAp/HA) composite scaffolds with different HA contents were developed by blending, cross-linking and freeze-drying, and their physicochemical properties and cell biocompatibilityin vitrowere subsequently studied. It was observed that the molecular conformation of the composite scaffolds was mainly composed of silk I and a small amount of theβ-sheets structure. On enhancing the HA content, the pore size of the scaffold decreased, while the porosity, water absorption, swelling ratio and mechanical properties were observed to increase. In particular, the SF/nHAp/HA scaffold with a 5.0 wt% ratio exhibited the highest water absorption and mechanical properties among the developed materials. In addition, thein vitrocytocompatibility analysis showed that the bone marrow mesenchymal stem cells exhibited excellent cell proliferation and osteogenic differentiation ability on the SF/nHAp/5.0 wt%HA scaffolds, as compared with the other scaffolds. It can be concluded that the developed composite scaffolds represent a promising class of materials for the bone tissue repair and regeneration.

Effects of different aperture-sized type I collagen/silk fibroin scaffolds on the proliferation and differentiation of human dental pulp cells

This study aimed at evaluate the effects of different aperture-sized type I collagen/silk fibroin (CSF) scaffolds on the proliferation and differentiation of human dental pulp cells (HDPCs). The CSF scaffolds were designed with 3D mapping software Solidworks. Three different aperture-sized scaffolds (CSF1-CSF3) were prepared by low-temperature deposition 3D printing technology. The morphology was observed by scanning electron microscope (SEM) and optical coherence tomography. The porosity, hydrophilicity and mechanical capacity of the scaffold were detected, respectively. HDPCs (third passage, 1 × 10⁵ cells) were seeded into each scaffold and investigated by SEM, CCK-8, alkaline phosphatase (ALP) activity and HE staining. The CSF scaffolds had porous structures with macropores and micropores. The macropore size of CSF1 to CSF3 was 421 ± 27 μm, 579 ± 36 μm and 707 ± 43 μm, respectively. The porosity was 69.8 ± 2.2%, 80.1 ± 2.8% and 86.5 ± 3.3%, respectively. All these scaffolds enhanced the adhesion and proliferation of HDPCs. The ALP activity in the CSF1 group was higher than that in the CSF3 groups (P < 0.01). HE staining showed HDPCs grew in multilayer within the scaffolds. CSF scaffolds significantly improved the adhesion and ALP activity of HDPCs. CSF scaffolds were promising candidates in dentine-pulp complex regeneration.

Advanced mycelium materials as potential self-growing biomedical scaffolds

Mycelia, the vegetative part of fungi, are emerging as the avant-garde generation of natural, sustainable, and biodegradable materials for a wide range of applications. They are constituted of a self-growing and interconnected fibrous network of elongated cells, and their chemical and physical properties can be adjusted depending on the conditions of growth and the substrate they are fed upon. So far, only extracts and derivatives from mycelia have been evaluated and tested for biomedical applications. In this study, the entire fibrous structures of mycelia of the edible fungi Pleurotus ostreatus and Ganoderma lucidum are presented as self-growing bio-composites that mimic the extracellular matrix of human body tissues, ideal as tissue engineering bio-scaffolds. To this purpose, the two mycelial strains are inactivated by autoclaving after growth, and their morphology, cell wall chemical composition, and hydrodynamical and mechanical features are studied. Finally, their biocompatibility and direct interaction with primary human dermal fibroblasts are investigated. The findings demonstrate the potentiality of mycelia as all-natural and low-cost bio-scaffolds, alternative to the tissue engineering systems currently in place.

Fabrication of nanocomposite/nanofibrous functionally graded biomimetic scaffolds for osteochondral tissue regeneration

One of the main challenges in treating osteochondral lesions via tissue engineering approach is providing scaffolds with unique characteristics to mimic the complexity. It has led to application of heterogeneous scaffolds as a potential candidate for engineering of osteochondral tissues, in which graded multilayered-structure should promote bone and cartilage growth. By designing three-dimensional (3D)-nanofibrous scaffolds mimicking the native extracellular matrix's nanoscale structure, cells can grow in controlled conditions and regenerate the damaged tissue. In this study, novel 3D-functionality graded nanofibrous scaffolds composed of five layers based on different compositions containing polycaprolactone(PCL)/gelatin(Gel)/nanohydroxyapatite (nHA) for osteoregeneration and chitosan(Cs)/polyvinylalcohol(PVA) for chondral regeneration are introduced. This scaffold is fabricated by electrospinning technique using spring as collector to create 3D-nanofibrous scaffolds. Fourier-transform infrared spectroscopy, X-ray diffraction, energy dispersive X-ray spectroscopy, scanning electron microscopy, mechanical compression test, porosimetry, and water uptake studies were applied to study each layer's physicochemical properties and whole functionally graded scaffold. Besides, biodegradation and biological studies were done to investigate biological performance of scaffold. Results showed that each layer has a fibrous structure with continuous nanofibers with improved pore size and porosity of novel 3D scaffold (6-13 μm and 90%) compared with two-dimensional (2D) mat (2.2 μm and 19.3%) with higher water uptake capacity (about 100 times of 2D mat). Compression modulus of electrospun scaffold was increased to 78 MPa by adding nHA. The biological studies revealed that the layer designed for osteoregeneration could improve cell proliferation rate in comparison to the layer designed for chondral regeneration. These results showed such structure possesses a promising potential for the treatment of osteochondral defects.

Modern Porous Polymer Implants: Synthesis, Properties, and Application

Abstract

The needs of modern surgery triggered the intensive development of transplantology, medical materials science, and tissue engineering. These directions require the use of innovative materials, among which porous polymers occupy one of the leading positions. The use of natural and synthetic polymers makes it possible to adjust the structure and combination of properties of a material to its particular application. This review generalizes and systematizes the results of recent studies describing requirements imposed on the structure and properties of synthetic (or artificial) porous polymer materials and implants on their basis and the advantages and limitations of synthesis methods. The most extensively employed, promising initial materials are considered, and the possible areas of application of polymer implants based on these materials are highlighted.

Salt-responsive polyampholyte-based hydrogel actuators with gradient porous structures

A polyampholyte-based hydrogel actuator with water-responsive shape deformation was fabricated, and the gradient distribution of chemical composition was proved by micro-FTIR.

3D printed hydrogels with oxidized cellulose nanofibers and silk fibroin for the proliferation of lung epithelial stem cells

A novel biomaterial ink consisting of regenerated silk fibroin (SF) and 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-oxidized bacterial cellulose (OBC) nanofibrils was developed for 3D printing lung tissue scaffold. Silk fibroin backbones were cross-linked using horseradish peroxide/H₂O₂ to form printed hydrogel scaffolds. OBC with a concentration of 7wt% increased the viscosity of inks during the printing process and further improved the shape fidelity of the scaffolds. Rheological measurements and image analyses were performed to evaluate inks printability and print shape fidelity. Three-dimensional construct with ten layers could be printed with ink of 1SF-2OBC (SF/OBC = 1/2, w/w). The composite hydrogel of 1SF-1OBC (SF/OBC = 1/1, w/w) printed at 25 °C exhibited a significantly improved compressive strength of 267 ± 13 kPa and a compressive stiffness of 325 ± 14 kPa at 30% strain, respectively. The optimized printing parameters for 1SF-1OBC were 0.3 bar of printing pressure, 45 mm/s of printing speed and 410 μm of nozzle diameter. Furthermore, OBC nanofibrils could be induced to align along the print lines over 60% degree of orientation, which were analyzed by SEM and X-ray diffraction. The orientation of OBC nanofibrils along print lines provided physical cues for guiding the orientation of lung epithelial stem cells, which maintained the ability to proliferate and kept epithelial phenotype after 7 days' culture. The 3D printed SF-OBC scaffolds are promising for applications in lung tissue engineering.

Electrospun regenerated Antheraea pernyi silk fibroin scaffolds with improved pore size, mechanical properties and cytocompatibility using mesh collectors

Generally, electrospun silk fibroin scaffolds collected by traditional plates present limited pore size and mechanical properties, which may restrict their biomedical applications. Herein, regenerated Antheraea pernyi silk fibroin (RASF) with excellent inherent cell adhesion property was chosen as a raw material and the conductive metal meshes were used as collectors to prepare modified RASF scaffolds by electrospinning from its aqueous solution. A traditional intact plate was used as a control. The morphology and mechanical properties of the obtained scaffolds were investigated. Schwann cells were further used to assess the cytocompatibility and cell migration ability of the typical scaffolds. Interestingly, compared with the traditional intact plate, the mesh collector with an appropriate gap size (circa 7 mm) could significantly improve the pore size, porosity and mechanical properties of the RASF scaffolds simultaneously. In addition, the scaffold collected under this condition (RASF-7mmG) showed higher cell viability, deeper cell permeation and faster cell migration of Schwann cells. Combined with the excellent inherent properties of ASF and the obviously enhanced scaffold cytocompatibility and mechanical properties, the RASF-7mmG scaffold is expected to be a candidate with great potential for biomedical applications.

The impact of relative humidity on electrospun polymer fibers: From structural changes to fiber morphology

Electrospinning is one of the most important methods used for the production of nanostructured materials. Electrospun nanofibers are used in a wide spectrum of applications such as drug delivery systems, filtration, fog harvesting, tissue engineering, smart textiles, flexible electronics, and more. Control of the manufacturing process is essential for further technology developments. In electrospinning, relative humidity is a crucial parameter that influences nearly all the properties of the collected fibers, such as morphology, mechanical properties, liquid retention, wetting properties, phase composition, chain conformation, and surface potential. Relative humidity is a determining component of a reliable process as it governs charge dissipation and solvent evaporation. This review summarizes the electrospinning process and its applications, phase separation processes, and impact of relative humidity on the properties of polymer fibers. We investigated relative humidity effects on both hydrophilic and hydrophobic polymers using over 20 polymers and hundreds of solvent systems. Most importantly, we underlined the indisputable importance of relative humidity in process repeatability and demonstrated its impact on almost all aspects of fiber production from a solution droplet to an electrospun network.

Construction and application of textile-based tissue engineering scaffolds: a review

Tissue engineering (TE) provides a practicable method for tissue and organ repair or substitution. As the most important component of TE, a scaffold plays a critical role in providing a growing environment for cell proliferation and functional differentiation as well as good mechanical support. And the restorative effects are greatly dependent upon the nature of the scaffold including the composition, morphology, structure, and mechanical performance. Medical textiles have been widely employed in the clinic for a long time and are being extensively investigated as TE scaffolds. However, unfortunately, the advantages of textile technology cannot be fully exploited in tissue regeneration due to the ignoring of the diversity of fabric structures. Therefore, this review focuses on textile-based scaffolds, emphasizing the significance of the fabric design and the resultant characteristics of cell behavior and extracellular matrix reconstruction. The structure and mechanical behavior of the fabrics constructed by various textile techniques for different tissue repairs are summarized. Furthermore, the prospect of structural design in the TE scaffold preparation was anticipated, including profiled fibers and some unique and complex textile structures. Hopefully, the readers of this review would appreciate the importance of structural design of the scaffold and the usefulness of textile-based TE scaffolds in tissue regeneration.

Polycaprolactone/gelatin degradable vascular grafts simulating endothelium functions modified by nitric oxide generation

Aim: Host remolding with scaffolds degradation and rapid formation of a complete endothelium, are prospective solutions for improving performance of small diameter vascular grafts. Materials & methods: For this purpose, microfibrous polycaprolactone (PCL)/gelatin scaffolds were prepared by electrospinning and subsequently functionalized with heparin and organoselenium-immobilized polyethyleneimine for nitric oxide generation through layer-by-layer self-assembly. Results: Our results showed that modified PCL/gelatin grafts had strong catalytic nitric oxide generation capacity and facilitated the enhanced attachment of endothelial cells, compared with control scaffold groups. Meanwhile, the modified grafts exhibited good hemocombatility, rapid endothelialization and smooth muscle cell regeneration. Conclusion: Modification of biodegradable scaffolds, proposed in this work, could enhance biological functions of vascular grafts and provides new strategies for the construction of small diameter vascular grafts.

Zein/gelatin/nanohydroxyapatite nanofibrous scaffolds are biocompatible and promote osteogenic differentiation of human periodontal ligament stem cells

In bone tissue engineering, it is important for biomaterials to promote the osteogenic differentiation of stem cells to achieve tissue regeneration.