Carbon dots doped tungstic anhydride on graphene oxide nanopanels: A new picomolar-range creatinine selective enzymeless electrochemical sensor

Rapid electrodeposition of Cu nanoparticle film on Ni foam as an integrated 3D free-standing electrode for non-invasive and non-enzymatic creatinine sensing

High cost, inherent destabilization, and intricate fixing of enzyme molecules are the main drawbacks of enzyme-based creatinine sensors. The design of a low-cost, stabilizable, and enzyme-free creatinine sensing probe is essential to address these limitations. In this work, an integrated three-dimensional (3D) free-standing electrode was designed to serve as a non-enzymatic creatinine sensing platform and was fabricated by rapid electrodeposition of a dense copper nanoparticle film on nickel foam (Cu NP film/NF). This low-cost, stable, easy-to-fabricate, and binder-free Cu NP film/NF electrode has abundant active sites and excellent electrochemical performance. Cyclic voltammetry measurements show a wide linear range (0.25-24 mM), low detection limit (0.17 mM), and high sensitivity (306 μA mM-1 cm-2). The developed sensor shows high recovery of creatinine concentration in real urine. Besides, it has better specificity, reproducibility, and robustness in detecting creatinine. These excellent results suggest that a non-enzymatic creatinine sensor based on an integrated 3D free-standing Cu NP film/NF electrode has good potential for non-invasive detection of urinary creatinine.

A flexible capacity-metric creatinine sensor based on polygon-shape polyvinylpyrrolidone/CuO and Fe2O3 NRDs electrodeposited on three-dimensional TiO2-V2O5-Polypyrrole nanocomposite

The innovations of the present work include these items; (i) Design and preparation of three-dimensional flexible conductive polymeric nanocomposites (3D-FCPNCs) containing polypyrrole (PPy), V2O5 and TiO2 and modification of their surface with polygon-shape polyvinylpyrrolidone/CuO nanorods (PVP/CuO NRDs) and Fe2O3 NRDs using an hierarchical process based on isoelectric point (IEP), (ii) Application of the prepared surfaces as the flexible enzymeless creatinine sensors using four calibration curves (impedimetric, real capacitance (C'), imaginary capacitance (C″) and double layer capacitance (Cdl)) obtained from electrochemical impedance spectroscopy (EIS) technique. The best results have been obtained using PVP/CuO NRDs-Fe2O3 NRDs/TiO2-V2O5-PPy 3D-FCPNC hierarchical electrode with a wide range of the linear concentration range (10 nmol L-1 -1.3 mmol L-1). Although, determination of creatinine through extraction of parameters such as charge transfer resistance (Rct) and Cdl from measuring impedance at a wide range of frequencies provides useful information about the characteristics of the electrolyte/electrode interface, but measuring real and imaginary capacitances at a specific frequency instead of a wide frequency range can decrease the response time to lower than 1 min. Finally, the prepared hierarchical enzymeless sensors have been successfully used to estimate creatinine concentration in blood serum.

Heteroatom-engineered multicolor lignin carbon dots enabling bimodal fluorescent off-on detection of metal-ions and glutathione

Carbon dots (CDs) have emerged as a promising subclass of optical nanomaterials with versatile functions in multimodal biosensing. Howbeit the rapid, reliable and reproducible fabrication of multicolor CDs from renewable lignin with unique groups (e.g., -OCH3, -OH and -COOH) and alterable moieties (e.g., β-O-4, phenylpropanoid structure) remains challenging due to difficult-to-control molecular behavior. Herein we proposed a scalable acid-reagent strategy to engineer a family of heteroatom-doped multicolor lignin carbon dots (LCDs) that are functioned as the bimodal fluorescent off-on sensing of metal-ions and glutathione (GSH). Benefiting from the modifiable photophysical structure via heteroatom-doping (N, S, W, P and B), the multicolor LCDs (blue, green and yellow) with a controllable size distribution of 2.06-2.22 nm deliver the sensing competences to fluorometric probing the distinctive metal-ion systems (Fe3+, Al3+ and Cu2+) under a broad response interval (0-500 μM) with excellent sensitivity and limit of detection (LOD, 0.45-3.90 μM). Meanwhile, we found that the addition of GSH can efficiently restore the fluorescence of LCDs by forming a stable Fe3+-GSH complex with a LOD of 0.97 μM. This work not only sheds light on evolving lignin macromolecular interactions with tunable luminescent properties, but also provides a facile approach to synthesize multicolor CDs with advanced functionalities.

Flexible electrochemical sensor for highly sensitive and selective non-enzymatic detection of creatinine via electrodeposited copper over polymelamine formaldehyde

A non-enzymatic electrochemical biosensor was developed for highly sensitive detection of creatinine using copper nanoparticles supported over polymelamine formaldehyde. The synergy between the electrodeposited copper nanoparticles over the highly porous polymer (eCu-PMF) provided a greener platform to boost up the electron transport at the electrode electrolyte interface by eliminating the role of redox species as well as interference of major interferents like glucose, dopamine, and ascorbic acid in physiological media 0.1 M PBS (pH 7.4). The proposed sensor exhibited a wide detection range of 100 fM-60 mM with high sensitivities of 0.320 mA nM-1 cm-2 and 3.8 mA nM-1 cm-2. Moreover, the sensor was applied to real samples of serum creatinine and recoveries of 97 to 114% were found. Additionally, a paper-based flexible screen-printed electrode was fabricated which displayed an excellent activity with the same detection range of 100 fM-60 mM and long-term storage stability of 15 days.

An Electrochemical Sensor Based on Cu-MOF-199@MWCNTs Laden with CuNPs for the Sensitive Detection of Creatinine

In this study, the synthesis of Cu-MOF-199@multiwalled carbon nanotubes (Cu-MOF-199@MWCNTs) composites was achieved and utilized to create an advanced electrochemical sensor for creatinine (Cre) detection. The composites were modified on a glassy carbon electrode surface through direct drip coating, followed by the deposition of copper nanoparticles (CuNPs) via constant potential deposition. Characterized by various techniques and electrochemical analyses, the Cu-MOF-199@MWCNTs composite increased the CuNPs load, improving the detection sensitivity for Cre. Under optimal conditions, the modified electrode exhibited good linearity across a broad range of Cre concentrations (0.05-40.0 μM) with a low detection limit of 11.3 nM. The developed sensor demonstrated remarkable stability, reproducibility, and selectivity, showing promise in sensitive and accurate Cre detection in serum samples.

Electrodeposited copper nanoparticles for creatinine detection via the in situ formation of copper-creatinine complexes

Creatinine is an important biomarker of kidney diseases. In this work, a fast and facile electrochemical sensor was developed for creatinine detection based on the use of copper nanoparticle-modified screen-printed electrodes. The copper electrodes were prepared by simple electrodeposition of Cu²⁺ (aq). The electrochemically inactive creatinine was detected reductively via the in situ formation of copper-creatinine complexes. Two linear detection ranges, 0.28-3.0 mM and 3.0-20.0 mM, were achieved using differential pulse voltammetry, with the sensitivities of 0.824 ± 0.053 μA mM^-1 and 0.132 ± 0.003 μA mM^-1, respectively. The limit of detection was determined to be 0.084 mM. The sensor was validated in synthetic urine samples to yield 99.3% recovery (%RSD = 2.8), demonstrating high tolerance to possible interfering species. Finally, the stability of creatinine and its degradation kinetics at different temperatures were evaluated using our developed sensor. The loss of creatinine was found to be a first-order reaction with the activation energy of 64.7 kJ mol^-1.

Portable smartphone integrated 3D-Printed electrochemical sensor for nonenzymatic determination of creatinine in human urine

3D printing technologies are an attractive for fabricating electrochemical sensors due to their ease of operation, freedom of design, fast prototyping, low waste, and low cost. We report the fabrication of a simple 3D-printed electrochemical sensing device for non-enzymatic detection of creatinine, an important indicator of renal function. To create the 3D-printed electrodes (3DE), carbon black/polylactic acid (CB/PLA) composite filament was used. The 3DE was activated using 0.5 M NaOH via amperometry prior to use to improve electrochemical performance. To give selectivity for creatinine, the activated 3DE was modified with a copper oxide nanoparticle-ionic liquid/reduced graphene oxide (CuO-IL/rGO) composite. The modified 3DE was characterized using microscopy and electrochemistry. Cyclic voltammetry and amperometry were used to evaluate sensor performance. The modified 3DE provided electrocatalytic activity towards creatinine without enzymes. Under optimal conditions, the modified 3DE directly coupled with a portable smartphone potentiostat exhibited the linear detection range of 0.5-35.0 mM, and the limit of detection was 37.3 μM, which is sufficient for detecting creatinine in human urine samples. Furthermore, the other physiological compounds present in human urine were not detected on the modified 3DE. Therefore, the modified 3DE could be a tool for effective creatinine screening in the urine.

Visualized concentration sensors based on fluorescence indication in a dye-doped polymer microwire

We demonstrate visualized microwire sensors based on fluorescence indication for detecting the concentrations of the aqueous solutions. The single Rhodamine (RhB) doped polymer microwires (PMWs) which are excited by the waveguiding excitation method are used as the sensory area. According to the fluorescent microimages of the PMWs, stable periodic oscillations could be observed in the RhB-doped PMWs. The fluorescent period which is dependent on the concentration is further analyzed by image processing and information extraction algorithms. Corresponding to a 1.0% change, the period length change of the visualized sensor reaches ∼380 nm, ∼270 nm, and ∼300 nm in NaCl, KCl, and sucrose solutions, respectively. The dection limits of the three solutions are estimated to be around 1.5 × 10^-4%. The dye-doped PMW sensors by fluorescence indication and image analysis proposed here realize the direct visualized detection in concentration sensing, making it possible to avoid the challenges of stability and weak signal detection and offer a potentially stable and cost-effective approach for micro/nanofiber sensor application.

Anodic SnO2 Nanoporous Structure Decorated with Cu2O Nanoparticles for Sensitive Detection of Creatinine: Experimental and DFT Study

Advanced anodic SnO₂ nanoporous structures decorated with Cu₂O nanoparticles (NPs) were employed for creatinine detection. Anodization of electropolished Sn sheets in 0.3 M aqueous oxalic acid electrolyte under continuous stirring produced complete open top, crack-free, and smooth SnO₂ nanoporous structures. Structural analyses confirm the high purity of rutile SnO₂ with successful functionalization of Cu₂O NPs. Morphological studies revealed the formation of self-organized and highly-ordered SnO₂ nanopores, homogeneously decorated with Cu₂O NPs. The average diameter of nanopores is ∼35 nm, while the average Cu₂O particle size is ∼23 nm. Density functional theory results showed that SnO₂@Cu₂O hybrid nanostructures are energetically favorable for creatinine detection. The hybrid nanostructure electrode exhibited an ultra-high sensitivity of around 24343 μA mM^-1 cm^-2 with an extremely lower detection limit of ∼0.0023 μM, a fast response time (less than 2 s), and wide linear detection ranges of 2.5-45 μM and 100 μM to 15 mM toward creatinine. This is ascribed to the creation of highly active surface sites as a result of Cu₂O NP functionalization, SnO₂ band gap diminution, and the formation of heterojunction and Cu(1)/Cu(ll)-creatinine complexes through secondary amines which occur in the creatinine structure. The real-time analysis of creatinine in blood serum by the fabricated electrode evinces the practicability and accuracy of the biosensor with reference to the commercially existing creatinine sensor. The proposed biosensor demonstrated excellent stability, reproducibility, and selectivity, which reflects that the SnO₂@Cu₂O nanostructure is a promising candidate for the non-enzymatic detection of creatinine.

Convex fiber-tapered seven core fiber-convex fiber (CTC) structure-based biosensor for creatinine detection in aquaculture

The purpose of this article is to propose an optical fiber sensor probe based on the localized surface plasma resonance (LSPR) technique for the detection of creatinine in aquaculture. The sensing probe is functionalized through the use of gold nanoparticles (AuNPs), niobium carbide (Nb₂CTx) MXene, and creatinase (CA) enzyme. The intrinsic total internal reflection (TIR) mechanism is modified to increase the evanescent field intensity using a heterogeneous core mismatch and tapering probe structure (i.e., convex fiber-tapered seven core fiber-convex fiber (CTC) structure). Strong evanescent fields can stimulate AuNPs and induce the LSPR effect, thereby increasing probe sensitivity. The specific recognition is enhanced by Nb₂CTx MXene adsorbing more active CA enzymes. The developed sensor probe has a sensitivity and limit of detection of 3.1 pm/µM and 86.12 µM, respectively, in the linear range of 0-2000 µM. Additionally, the sensor probe's reusability, reproducibility, stability, and selectivity were evaluated, with satisfactory results obtained with impact for areas like food protein, marine life and healthcare.

Electrochemical creatinine detection for advanced point-of-care sensing devices: a review

Creatinine is an amino acid derived from creatine catabolism at different steps of the body's organs, and its detection is significant because levels out of normal values are linked to some diseases like kidney failure. Normal concentration levels of creatinine in blood are from 45 to 110 μM, while in urine, typical concentrations range between 3.3 to 27 mM, and in saliva from 8.8 and 26.5 μM. Nowadays, the creatinine detection is carried through different spectroscopic-colorimetric methods; however, the resulting values present errors due to high interferences, delayed analysis, and poor stability. Electrochemical sensors have been an alternative to creatinine detection, and the electrochemical methods have been adapted to detect in enzymatic and non-enzymatic sensors, the latter being more relevant in recent years. Nanomaterials have made creatinine sensors more stable, sensitive, and selective. This review presents recent advances in creatinine electrochemical sensors for advances in point-of-care (POC) sensing devices, comprising both a materials point of view and prototypes for advanced sensing. The effect of the metal, particle size, shape and other morphological and electronic characteristics of nanomaterials are discussed in terms of their impact on the effective detection of creatinine. In addition, the application of nanomaterials in POC devices is revised pointing to practical applications and looking for more straightforward and less expensive devices to manufacture.

Creatinine is an amino acid derived from creatine catabolism at different steps of the body's organs, and its detection is significant because levels out of normal values are linked to some diseases like kidney failure.

An electrochemical sensor based on a Co3O4-ERGO nanocomposite modified screen-printed electrode for detection of uric acid in artificial saliva

In this study, we report the fabrication of a nanocomposite consisting of Co₃O₄ nanoparticles (Co₃O₄ NPs) and electrochemically reduced graphene oxide (ERGO) on a screen-printed electrode (SPE) and its sensing performance in the electrochemical detection of uric acid (UA). The surface modification of the electrode was confirmed by using a variety of characterization techniques (FE-SEM, XRD, AFM, EDX, WCA, FTIR, and Raman spectroscopy). In addition, the surface modification was electrochemically characterized step by step through CV, EIS and DPV techniques, and the results showed that the Co₃O₄-ERGO nanocomposite exhibited highly sensitive and selective sensing performance towards the oxidation of UA in 0.1 M (pH 7.0) phosphate buffer solution (PBS). The sensor (Co₃O₄-ERGO/SPE) signals were observed to be linear to the UA concentration in the range of 5 μM to 500 μM (R² = 0.9985). After revealing its other performance characteristics, such as repeatability, reproducibility, stability, sensitivity, and selectivity, the sensor was successfully applied to the analysis of UA in artificial saliva samples.

Facile Detection of Blood Creatinine Using Binary Copper-Iron Oxide and rGO-Based Nanocomposite on 3D Printed Ag-Electrode under POC Settings

Metal nanoparticles have been helpful in creatinine sensing technology under point-of-care (POC) settings because of their excellent electrocatalyst properties. However, the behavior of monometallic nanoparticles as electrochemical creatinine sensors showed limitations concerning the current density in the mA/cm² range and wide detection window, which are essential parameters for the development of a sensor for POC applications. Herein, we report a new sensor, a reduced graphene oxide stabilized binary copper-iron oxide-based nanocomposite on a 3D printed Ag-electrode (Fe-Cu-rGO@Ag) for detecting a wide range of blood creatinine (0.01 to 1000 μM; detection limit 10 nM) in an electrochemical chip with a current density ranging between 0.185 and 1.371 mA/cm² and sensitivity limit of 1.1 μA μM^-1 cm^-2 at physiological pH. Interference studies confirmed that the sensor exhibited no interference from analytes like uric acid, urea, dopamine, and glutathione. The sensor response was also evaluated to detect creatinine in human blood samples with high accuracy in less than a minute. The sensing mechanism suggested that the synergistic effects of Cu and iron oxide nanoparticles played an essential role in the efficient sensing where Fe atoms act as active sites for creatinine oxidation through the secondary amine nitrogen, and Cu nanoparticles acted as an excellent electron-transfer mediator through rGO. The rapid sensor fabrication procedure, mA/cm² peak current density, a wide range of detection limits, low contact resistance including high selectivity, excellent linear response (R² = 0.991), and reusability ensured the application of advanced electrochemical sensor toward the POC creatinine detection.

Effective and reliable platform for nonenzymatic nanomolar-range quinol detection in water samples using ceria doped polypyrrole nanocomposite embedded on graphitic carbon nitride nanosheets

A glassy carbon electrode modification by a novel ternary nanocomposite of advantageously united ceria, polypyrrole, and graphitic carbon nitride (CeO₂/Ppy@g-C₃N₄) is reported here. It can be used to tailor the sensor surface for the electrochemical detection of nanomolar-level quinol (Qnl), a chemical widely used as a developing agent in photography and lithography, as a cosmetic, and as an antioxidant in rubber and food industries. The occupational exposure of Qnl may occur by inhalation or dermal contact, leading to lot of health hazards. The synthesized nanocomposite was characterized by various analytical techniques such as UV-Vis, Fourier transformed infrared (FTIR), X-ray powder diffraction, field emission scanning electron microscopy, high-resolution transmission electron microscopy, Raman, thermogravimetric analysis, energy-dispersive X-ray spectroscopy, selected area electron diffraction, and elemental mapping analyses. The oxidation current of Qnl is linear to its concentration in the range of 0.01-260 μM and the lowest detection and quantification limit are found to be 1.5 nM and 0.004 μM, respectively, with a sensitivity of 283.33 μA mM^-1 cm^-2. The performance of the modified electrode was compared with those of high-performance liquid chromatography, which indicates that the proposed sensor can be used as an effective and reliable platform for nano-molar detection of Qnl in various environmental and biological fluids.

Advanced materials-integrated electrochemical sensors as promising medical diagnostics tools: A review

Electrochemical sensors have increasingly been linked with terms as modern biomedically effective highly selective and sensitive devices, wearable and wireless technology, portable electronics, smart textiles, energy storage, communication and user-friendly operating systems. The work brings the overview of the current advanced materials and their application strategies for improving performance, miniaturization and portability of sensing devices. It provides the extensive information on recently developed (bio)sensing platforms based on voltammetric, amperometric, potentiometric and impedimetric detection modes including portable, non-invasive, wireless, and self-driven miniaturized devices for monitoring human and animal health. Diagnostics of selected free radical precursors, low molecular biomarkers, nucleic acids and protein-based biomarkers, bacteria and viruses of today's interest is demonstrated.

A new CQDs/f-MWCNTs/GO nanocomposite electrode for arsenic (10−12M) quantification in bore-well water and industrial effluents

Strategic combination ofCQDs/f-MWCNTs/GO/GCE for pico-molar arsenic sensing.

Enzyme-free detection of uric acid using hydrothermally prepared CuO·Fe2O3 nanocrystals

Copper oxide doped iron oxide nanocrystals (CuO·Fe₂O₃ NCs) were prepared using a simple hydrothermal technique at low temperature in an alkaline medium.