Flow-induced crystallization of isotactic polypropylene: Modeling formation of multiple crystal phases and morphologies

Deformation-Induced Phase Transitions in iPP Polymorphs

This detailed study reveals the relation between structural evolution and the mechanical response of α -, β - and γ -iPP. Uni-axial compression experiments, combined with in situ WAXD measurements, allowed for the identification of the evolution phenomena in terms of phase composition. Tensile experiments in combination with SAXS revealed orientation and voiding phenomena, as well as structural evolution in the thickness of the lamellae and amorphous layers. On the level of the crystallographic unit cell, the WAXD experiments provided insight into the early stages of deformation. Moreover, transitions in the crystal phases taking place in the larger deformation range and the orientation of crystal planes were monitored. At all stretching temperatures, the crystallinity decreases upon deformation, and depending on the temperature, different new structures are formed. Stretching at low temperatures leads to crystal destruction and the formation of the oriented mesophase, independent of the initial polymorph. At high temperatures, above T α c , all polymorphs transform into oriented α -iPP. Small quantities of the initial structures remain present in the material. The compression experiments, where localization phenomena are excluded, show that these transformations take place at similar strains for all polymorphs. For the post yield response, the strain hardening modulus is decisive for the mechanical behavior, as well as for the orientation of lamellae and the evolution of void fraction and dimensions. β -iPP shows by far the most intense voiding in the entire experimental temperature range. The macroscopic localization behavior and strain at which the transition from disk-like void shapes, oriented with the normal in tensile direction, into fibrillar structures takes place is directly correlated with the strain hardening modulus.

Full Characterization of Multiphase, Multimorphological Kinetics in Flow-Induced Crystallization of IPP at Elevated Pressure

Understanding the complex crystallization behavior of isotactic polypropylene (iPP) in conditions comparable to those found in polymer processing, where the polymer melt experiences a combination of high shear rates and elevated pressures, is key for modeling and therefore predicting the final structure and properties of iPP products. Coupling a unique experimental setup, capable to apply wall shear rates similar to those experienced during processing and carefully control the pressure before and after flow is imposed, with in situ X-ray scattering and diffraction techniques (SAXS and WAXD) at fast acquisition rates (up to 30 Hz), a well-defined series of short-term flow experiments are carried out using 16 different combinations of wall shear rates (ranging from 110 to 440 s-1) and pressures (100-400 bar). A complete overview on the kinetics of structure development during and after flow is presented. Information about shish formation and growth of α-phase parents lamellae from the shish backbones is extracted from SAXS; the overall apparent crystallinity evolution, amounts of different phases (α, β, and γ), and morphologies developing in the shear layer (parent and daughter lamellae both in α and γ phase) are fully quantified from the analysis of WAXD data. Both flow rate and pressure were found to have a significant influence on the nucleation and the growth process of oriented and isotropic structures. Flow affects shish formation and the growth of α-parents; pressure acts on relaxation times, enhancing the effect of flow, and (mainly) on the growth rate of γ-phase. The remarkably high amount of γ-lamellae found in the oriented layer strongly indicates the nucleation of γ directly from the shish backbone. All the observations were conceptually in agreement with the flow-induced crystallization model framework developed in our group and represent a unique and valuable data set that will be used to further validate and implement our numerical modeling, filling the gap for quantitatively modeling crystallization during complicated processing operations like injection molding.

The non-equilibrium phase diagrams of flow-induced crystallization and melting of polyethylene

Combining extensional rheology with in-situ synchrotron ultrafast x-ray scattering, we studied flow-induced phase behaviors of polyethylene (PE) in a wide temperature range up to 240 °C. Non-equilibrium phase diagrams of crystallization and melting under flow conditions are constructed in stress-temperature space, composing of melt, non-crystalline δ, hexagonal and orthorhombic phases. The non-crystalline δ phase is demonstrated to be either a metastable transient pre-order for crystallization or a thermodynamically stable phase. Based on the non-equilibrium phase diagrams, nearly all observations in flow-induced crystallization (FIC) of PE can be well understood. The interplay of thermodynamic stabilities and kinetic competitions of the four phases creates rich kinetic pathways for FIC and diverse final structures. The non-equilibrium flow phase diagrams provide a detailed roadmap for precisely processing of PE with designed structures and properties.