The unforeseen relationship of Fe2O3 and ZnO on fibrous silica KCC-1 catalyst for fabricated Z-scheme extractive-photooxidative desulphurization

Vanadia as an electron-hole recombination inhibitor on fibrous silica-titania for selective hole oxidation of ciprofloxacin and Congo red photodegradation

Vanadia (V2O5)-incorporated fibrous silica-titania (V/FST) catalysts, which were successfully synthesized using a hydrothermal method followed by the impregnation of V2O5. The catalysts were then characterized using numerous techniques, including X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, nitrogen adsorption-desorption analyses, ultraviolet-visible diffuse reflectance spectroscopy, Fourier-transform infrared, X-ray photoelectron spectroscopy, and photoluminescence (PL) analyses. The study found that varying the amount of V2O5 (1-10 wt%) had a significant impact on the physicochemical properties of the FST, which in turn improved the photodegradation efficiency of two organic compounds, ciprofloxacin (CIP) and congo red (CR). 5V/FST demonstrated the best performance in degrading 10 mg L-1 of CIP (83%) and CR (100%) at pH 3 using 0.375 g L-1 catalyst under visible light irradiation within 180 min. The highest photoactivity of 5V/FST is mainly due to higher crystallinity and the highest number of V2O5-FST interactions. Furthermore, as demonstrated by PL analysis, the 5V/FST catalyst has the most significant impact on interfacial charge transfer and reduces electron-hole recombination. The photodegradation of both contaminants follows the Langmuir-Hinshelwood pseudo-first-order model, according to the kinetic study. The scavenger investigation demonstrated that hydroxyl radicals and holes dominated species in the system, indicating that the catalyst effectively generated reactive species for pollutant degradation. A possible mechanism was also identified for FST and 5V/FST. Interestingly, V2O5 acts as an electron-hole recombination inhibitor on FST for selective hole oxidation of ciprofloxacin and congo red photodegradation. Finally, the degradation efficiency of the catalyst remained relatively stable even after five cyclic experiments, indicating its potential for long-term use in environmental remediation.

Co-production of hydrogen and carbon nanotubes by catalytic cracking of waste cooking oil model compound over Ni-Cu/Al-KCC-1

Ni-Cu/Al-KCC-1 catalysts with different metal contents were prepared using fibrous nano-silica (Al-KCC-1) as a support. Field emission scanning electron microscopy observations showed that the spherical particle morphology and fibrous structure of the Al-KCC-1 were not changed after metal loading. Transmission electron microscopy images demonstrated that the introduction of copper improved the dispersion of the nickel, while X-ray diffraction and hydrogen temperature-programmed reduction confirmed the formation of a Ni-Cu alloy. The N₂-Brunauer-Emmett-Teller specific surface areas of the catalysts were in the range of 269-378 m²/g and the average pore diameters were 7.988-12.078 nm. These Ni-Cu/Al-KCC-1 catalysts were used to promote the cracking of waste cooking oil model compound (WCOMC) to produce H₂ and carbon nanotubes (CNTs), and the 10 wt% Ni-5 wt% Cu/Al-KCC-1 exhibited the highest catalytic activity. At a WCOMC flow rate of 0.04 mL/min and 750 °C, the instantaneous volume fraction of H₂ reached 49.8 vol% and the content of H₂ in the gaseous product was close to 71.4 vol%.

CuO improved energy band of AgO/fibrous SiO2-ZrO2 for optimized simultaneous photocatalytic redox of chromium (VI) and p-cresol using response surface methodology

Ternary CuO/AgO/FSZr photocatalysts were fabricated via the hydrothermal and electrochemical methods with three different CuO loading (1, 3 and 5 wt%), indicated as 1CuO/AgO/FSZr, 3CuO/AgO/FSZr and 5CuO/AgO/FSZr. The photocatalytic reaction was tested towards simultaneous chromium (VI) photoreduction and p-cresol photooxidation and the performance in order as follow: 3CuO/AgO/FSZr > 5CuO/AgO/FSZr > 1CuO/AgO/FSZr > AgO/FSZr > FSZr. CuO/AgO/FSZr photocatalysts showed an improvement in photocatalytic activity compared to AgO/FSZr and FSZr due to the reduction potential of chromium (VI) aligned closer to the conduction band of CuO and provided abundant free active electrons (e^-) and holes (h⁺) with efficient transportation and migration. Interestingly, the 3CuO/AgO/FSZr was established as the best photocatalyst with 98% reduction of chromium (VI) and 83% oxidation of p-cresol simultaneously, owing to its strong corporation between the metal oxides and support and higher total pore volume. The Langmuir-Hinshelwood model were employed for kinetics which followed the pseudo-first-order kinetics model well. Based on the simultaneous photocatalytic mechanism, chromium (VI) and p-cresol were directly reduced and oxidized by e^- and h⁺, respectively. The response surface methodology (RSM) discovered that the quadratic term initial concentration of chromium (VI) is the main significant factor in photocatalytic performance. The optimum parameters for simultaneous photoredox of chromium (VI) and p-cresol predicted from RSM are 9.6 mg L^-1 of chromium (VI) concentration, 9.8 mg L^-1 of p-cresol concentration and 0.32 g L^-1 of catalyst dosage. Under these conditions the error between the predicted and experimental values is only 3.7%. The 3CuO/AgO/FSZr sustained the photocatalytic performance after reused for five cycles and could oxidized various organic pollutants as well as reduced chromium (VI) simultaneously.

Synthesis of Mesoporous Silica Incorporated with Low Iron Concentration and Gelatin Co-Template via The Ultrasonication Method and Its Methylene Blue Photodegradation Performance

In this work, low iron concentration incorporated on mesoporous silica with gelatin co-template (Fe2O3/GSBA-15) has been successfully synthesized via the ultrasonication method. The physical, chemical, and structural properties of the samples were investigated with X-Ray Diffraction (XRD), Scanning Electron Microscope- Energy Dispersive X-Ray (SEM-EDX), Fourier Transform Infra-Red (FTIR), and N2 adsorption-desorption. Results showed good distribution of low concentration of iron oxide on the gelatin mesoporous silica GSBA-15. Elemental and surface analysis presented that iron oxide incorporation with higher concentration exhibited lower surface area due to the blocking pore. The highest photocatalytic activity on the methylene blue dye degradation was achieved at 10% Fe2O3/GSBA-15 with ~80% efficiency. The results revealed that the photocatalytic activity of Fe2O3/GSBA-15 enhanced with the presence of iron oxide. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Promoting a well-dispersion of MoO3 nanoparticles on fibrous silica catalyst via one-pot synthesis for enhanced photoredox environmental pollutants efficiency

The coexistence of pharmaceutical compounds and heavy metals in the aquatic environment has resulted in complications in the treatment process and thus, causing uproar among the citizens. The radical-based photocatalysis technology has aroused as an excellent method to eliminate both heavy metal and pharmaceutical compounds in the water. Herein, reported the utilization of the microemulsion technique for the preparation of nanoporous fibrous silica-molybdenum oxide (FSMo) towards simultaneous photocatalytic abatement of hexavalent chromium (Cr(VI)) and tetracycline (TC). The FESEM analysis showed the spherical morphology of the FSMo catalyst with dendrimeric silica fiber. The synthesized FSMo catalyst exhibited narrowed bandgap, high crystallinity, and well Mo element dispersion for enhanced photo-redox of Cr(VI) and TC. Remarkably, simultaneous remediation of the Cr(VI) and TC over FSMo demonstrated superior photocatalytic efficiency, 69% and 75%, respectively, than in the individual system, possibly due to the effective separation of photoinduced charges. The introduction of the Mo element to the silica framework via microemulsion technique demonstrated better dispersion of Mo compared to the incipient wetness impregnation method and thus, yielded higher photocatalytic activity towards simultaneous removal of TC and Cr(VI). Besides, quenching experiments revealed the electrons and holes as the active species that play a dominant role in the simultaneous photo-redox of Cr(VI) and TC. Lastly, the FSMo catalyst demonstrated high stability after four continuous cycles of simultaneous photocatalysis reactions, implying its potential as a suitable material for practical wastewater treatments.

New insight into the kinetic study on the different loadings of the CuO/CNT catalyst and its optimization for p-chloroaniline photodegradation

The effect of the copper (Cu) content on Cu oxide loaded onto a carbon nanotube (CuO/CNT) catalyst on the mechanistic, kinetic, and photonic efficiency of the photodegradation of p-chloroaniline (PCA) under visible (Vis) and ultraviolet (UV) light irradiation has been explored. For low-loading (1-5 wt%) CuO/CNTs, photodegradation performed better under UV (>84%) rather than the Vis system; this may be due to the presence of abundant defect sites on both CuO and CNTs, which allowed the multielectron reduction of oxygen at their impurity levels to generate more hydrogen peroxide and subsequent ·OH radicals. The active species under UV were in the following order: h⁺ ≫ e^- > ·OH, while it was vice versa for the Vis system with a well-balanced 50 wt% CuO/CNT catalyst that exhibited a similar performance. The kinetic study showed the transition of the kinetic order from the zeroth to the first order on increasing the PCA concentration under the Vis system and vice versa for the UV system. The Thiele modulus (ϕ) further confirmed that the effect of internal mass transfer was negligible under UV light. In contrast, the transition from mass transfer to kinetic control limitation was observed under the Vis system. The optimum PCA degradation predicted from the response surface analysis was 97.36% at the reaction pH of 7.3, catalyst dosage of 0.45 g L^-1, and initial PCA concentration of 11.02 mg L^-1. The condition obtained was fairly close to the forecasted value with an error of 0.26%.

A review on synergistic coexisting pollutants for efficient photocatalytic reaction in wastewater remediation

With the tremendous development of the economy and industry, the pollution of water is becoming more serious due to the excessive chemical wastes that need to remove thru reduction or oxidation reactions. Simultaneous removal of dual pollutants via photocatalytic redox reaction has been tremendously explored in the last five years due to effective decontamination of pollutants compared to a single pollutants system. In a photocatalysis mechanism, the holes in the valence band can remarkably promote the oxidation of a pollutant. At the same time, photoexcited electrons are also consumed for the reduction reaction. The synergistic between the reduction and oxidation inhibits the recombination of electron-hole pairs extending their lifetime. In this review, the binary pollutants that selectively removed via photocatalysis reduction or oxidation are classified according to heavy metal-organic pollutant (HM/OP), heavy metal-heavy metal (HM/HM) and organic-organic pollutants (OP/OP). The intrinsic between the pollutants was explained in three different mechanisms including inhibition of electron-hole recombination, ligand to metal charge transfer and electrostatic attraction. Several strategies for the enhancement of this treatment method which are designation of catalysts, pH of mixed pollutants and addition of additive were discussed. This review offers a recent perspective on the development of photocatalysis system for industrial applications.

Recent advances on nanocellulose biomaterials for environmental health photoremediation: An overview

As one of the potential bionanomaterials, nanocellulose has appeared as a favorable candidate for photoremediation of the environment because of its abundance in nature, inexpensive, eco-friendly, decomposable, high surface area, and outstanding mechanical properties. The current review carefully summarized the diverse type of nanocellulose, their preparation approaches, and several previous works on the use of nanocellulose for photoremediation. These include the role of nanocellulose for the increased surface active site of the hybrid photocatalysts by providing a large surface area for enhanced adsorption of photons and pollutant molecules, as a dispersing agent to increase distribution of metal/non-metal dopants photocatalysts, as well as for controlled size and morphology of the dopants photocatalysts. Furthermore, the recommendations for upcoming research provided in this review are anticipated to ignite an idea for the development of other nanocellulose-based photocatalysts. Other than delivering beneficial information on the present growth of the nanocellulose biomaterials photocatalysts, this review is expected will attract more interest to the utilization of nanocellulose photocatalyst and distribute additional knowledge in this exciting area of environmental photoremediation. This could be attained by considering that a review on nanocellulose biomaterials for environmental health photoremediation has not been described elsewhere, notwithstanding intensive research works have been dedicated to this topic.

Density Functional Theory Study on the Adsorption Mechanism of Sulphide Gas Molecules on α-Fe2O3(001) Surface

Sulphide gas is an impurity that affects the quality of natural gas, which needs reasonable storage and transportation. In this work, we investigated the adsorption structure and electronic behavior of hydrogen sulfide (H2S), carbonyl sulfur (COS), and methyl mercaptan (CH3SH) on sulphide gas molecules on pure and vacant α-Fe2O3(001) surfaces by density functional theory with geometrical relaxations. The results show that H2S and CH3SH are mainly adsorbed in the form of molecules on the pure Fe2O3(001) surface. On the vacant α-Fe2O3(001) surface, they can be adsorbed on Fe atoms in molecular form and by dissociation. The absolute value of the adsorption energy of H2S and CH3SH on the vacancy defect α-Fe2O3 surface is larger, and the density of states show that the electron orbital hybridization is more significant, and the adsorption is stronger. The charge differential density and Mulliken charge population analysis show that the charge is rearranged and chemical bonds are formed. The affinity of H2S to the vacancy α-Fe2O3(001) surface is slightly higher than that of CH3SH, while COS molecules basically do not adsorb on the α-Fe2O3(001) surface, which may be related to the stable chemical properties of the molecules themselves.

Simultaneous photocatalytic reduction of hexavalent chromium and oxidation of p-cresol over AgO decorated on fibrous silica zirconia

The co-existence of heavy metals and organic compounds including Cr(VI) and p-cresol (pC) in water environment becoming a challenge in the treatment processes. Herein, the synchronous photocatalytic reduction of Cr(VI) and oxidation of pC by silver oxide decorated on fibrous silica zirconia (AgO/FSZr) was reported. In this study, the catalysts were successfully developed using microemulsion and electrochemical techniques with various AgO loading (1, 5 and 10 wt%) and presented as 1, 5 and 10-AgO/FSZr. Catalytic activity was tested towards simultaneous photoredox of hexavalent chromium and p-cresol (Cr(VI)/pC) and was ranked as followed: 5-AgO/FSZr (96/78%) > 10-AgO/FSZr (87/61%) > 1-AgO/FSZr (47/24%) > FSZr (34/20%). The highest photocatalytic activity of 5-AgO/FSZr was established due to the strong interaction between FSZr and AgO and the lowest band gap energy, which resulted in less electron-hole recombination and further enhanced the photoredox activity. Cr(VI) ions act as a bridge between the positive charge of catalyst and cationic pC in pH 1 solution which can improve the photocatalytic reduction and oxidation of Cr(VI) and pC, respectively. The scavenger experiments further confirmed that the photogenerated electrons (e^-) act as the main species for Cr(VI) to be reduced to Cr(III) while holes (h⁺) and hydroxyl radicals are domain for photooxidation of pC. The 5-AgO/FSZr was stable after 5 cycles of reaction, suggesting its potential for removal of Cr(VI) and pC simultaneously in the chemical industries.