Fused-ring bislactone building blocks for polymer donors

Design of a Fully Non-Fused Bulk Heterojunction toward Efficient and Low-Cost Organic Photovoltaics

To modulate the miscibility between donor and acceptor materials both possessing fully non-fused ring structures, a series of electron acceptors (A4T-16, A4T-31 and A4T-32) with different polar functional substituents were synthesized and investigated. The three acceptors show good planarity, high conformational stability, complementary absorption and energy levels with the non-fused polymer donor (PTVT-BT). Among them, A4T-32 possesses the strongest polar functional group and shows the highest surface energy, which facilitates morphological modulation in the bulk heterojunction (BHJ) blend. Benefiting from the proper morphology control method, an impressive power conversion efficiency (PCE) of approaching 16.0 % and a superior fill factor over 0.795 are achieved in the PTVT-BT : A4T-32-based organic photovoltaic cells with superior photoactive materials price advantage, which represent the highest value for the cells based on the non-fused blend films. Notably, this cell maintains ≈84 % of its initial PCE after nearly 2000 h under the continuous simulated 1-sun-illumination. In addition, the flexible PTVT-BT : A4T-32-based cells were fabricated and delivered a decent PCE of 14.6 %. This work provides an effective molecular design strategy for the non-fused non-fullerene acceptors (NFAs) from the aspect of bulk morphology control in fully non-fused BHJ layers, which is crucial for their practical applications.

Combining Polymer Zwitterions and Zinc Oxide for High Performance Inverted Organic Solar Cells

Zinc oxide (ZnO) is a widely used cathode interlayer material in inverted organic solar cells (OSCs). However, there are lots of surface or bulk film defects in ZnO layers, which degrades solar cell performance. Here, the typical phosphorylcholine- and sulfobetaine-based polymer zwitterions (PMPC and PDMAPS) were synthesized via reversible addition-fragmentation chain-transfer (RAFT) polymerization to modify ZnO interlayers for inverted OSCs. The polymer zwitterions can efficiently passivate the defects in ZnO films and thus increase the conductivity of the ZnO interlayers. Both PMPC and PDMAPS modified ZnO interlayers show some general advantages on improving the performance of fullerene-based and non-fullerene-based OSCs. A highest efficiency of 16.69% was achieved by using PMPC modified ZnO interlayers in PM6:Y6 based solar cell devices, which is among the best performance in inverted OSCs. Such an improvement on device performance is attribute to the work function reduction of the polymer zwitterions modified ZnO films, which provides an efficient cathode platform to extract and transport electrons from the active layers, to the benefit of suppressing interfacial charge recombination. As a result, the organic-inorganic hybrid composites (ZnO: polymer zwitterions) show efficient interfacial modification to align energy-levels at the device interface, which have promising application prospects in organic electronics. This article is protected by copyright. All rights reserved.

Thermoplastic Elastomer Tunes Phase Structure and Promotes Stretchability of High-Efficiency Organic Solar Cells

Top-performance organic solar cells (OSCs) consisting of conjugated polymer donors and nonfullerene small molecule acceptors (NF-SMAs) deliver rapid increases in efficiencies. Nevertheless, many of the polymer donors exhibit high stiffness and small molecule acceptors are very brittle, which limit their applications in wearable devices. Here, a simple and effective strategy is reported to improve the stretchability and reduce the stiffness of high-efficiency polymer:NF-SMA blends and simultaneously maintain the high efficiency by incorporating a low-cost commercial thermoplastic elastomer, polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS). The microstructure, mechanical properties, and photovoltaic performance of PM6:N3 with varied SEBS contents and the molecular weight dependence of SEBS on microstructure and mechanical properties are thoroughly characterized. This strategy for mechanical performance improvement exhibits excellent applicability in some other OSC blend systems, e.g., PBQx-TF:eC9-2Cl and PBDB-T:ITIC. More crucially, the elastic modulus of such complex ternary blends can be nicely predicted by a mechanical model. Therefore, incorporating thermoplastic elastomers is a widely applicable and cost-effective strategy to improve mechanical properties of nonfullerene OSCs and beyond.

Performance Enhancement of Organic Solar Cells by Adding a Liquid Crystalline Molecule in Cathode and Anode Interlayers

In this study, an effective and simple approach for optimizing the performance of both cathode and anode interlayers in OSCs is demonstrated using 4-heptyl-4'-cyanobiphenyl (7CB) to dope a classic cathode (ZnO and SnO₂) or an anode interlayer [poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)]. Because of the enhanced light absorption, improved physical contact between a photoactive layer and an interlayer, and increased carrier recombination, all of the devices based on a 7CB-doped interlayer show increased short-circuit current density (J_sc), fill factor (FF), and power conversion efficiency (PCE) compared to the corresponding undoped interlayer, regardless it is the anode interlayer or the cathode interlayer, which is a rare phenomenon in the interlayer modification field.