PBT assessment under REACH: Screening for low aquatic bioaccumulation with QSAR classifications based on physicochemical properties to replace BCF in vivo testing on fish

Screening Disinfection Byproducts in Arid-Coastal Wastewater: A Workflow Using GC×GC-TOFMS, Passive Sampling, and NMF Deconvolution Algorithm

Disinfection during tertiary municipal wastewater treatment is a necessary step to control the spread of pathogens; unfortunately, it also gives rise to numerous disinfection byproducts (DBPs), only a few of which are regulated because of the analytical challenges associated with the vast number of potential DBPs. This study utilized polydimethylsiloxane (PDMS) passive samplers, comprehensive two-dimensional gas chromatography (GC×GC) coupled with time-of-flight mass spectrometry (TOFMS), and non-negative matrix factorization (NMF) spectral deconvolution for suspect screening of DBPs in treated wastewater. PDMS samplers were deployed upstream and downstream of the chlorination unit in a municipal wastewater treatment plant located in Abu Dhabi, and their extracts were analyzed using GC×GC-TOFMS. A workflow incorporating a multi-tiered, eight-filter screening process was developed, which successfully enabled the reliable isolation of 22 candidate DBPs from thousands of peaks. The NMF spectral deconvolution improved the match factor score of unknown mass spectra to the reference mass spectra available in the NIST library by 17% and facilitated the identification of seven additional DBPs. The close match of the first-dimension retention index data and the GC×GC elution patterns of DBPs, both predicted using the Abraham solvation model, with their respective experimental counterparts-with the measured data available in the NIST WebBook and the GC×GC elution patterns being those observed for the candidate peaks-significantly enhanced the accuracy of peak assignment. Isotopic pattern analysis revealed a close correspondence for 11 DBPs with clearly visible isotopologues in reference spectra, thereby further strengthening the confidence in the peak assignment of these DBPs. Brominated analogues were prevalent among the detected DBPs, possibly due to seawater intrusion. The fate, behavior, persistence, and toxicity of tentatively identified DBPs were assessed using EPI Suite™ and the CompTox Chemicals Dashboard. This revealed their significant toxicity to aquatic organisms, including developmental, mutagenic, and endocrine-disrupting effects in certain DBPs. Some DBPs also showed activity in various CompTox bioassays, implicating them in adverse molecular pathways. Additionally, 11 DBPs demonstrated high environmental persistence and resistance to biodegradation. This combined approach offers a powerful tool for future research and environmental monitoring, enabling accurate identification and assessment of DBPs and their potential risks.

Predicting the Accumulation of Ionizable Pharmaceuticals and Personal Care Products in Aquatic and Terrestrial Organisms

The extent to which chemicals bioaccumulate in aquatic and terrestrial organisms represents a fundamental consideration for chemicals management efforts intended to protect public health and the environment from pollution and waste. Many chemicals, including most pharmaceuticals and personal care products (PPCPs), are ionizable across environmentally relevant pH gradients, which can affect their fate in aquatic and terrestrial systems. Existing mathematical models describe the accumulation of neutral organic chemicals and weak acids and bases in both fish and plants. Further model development is hampered, however, by a lack of mechanistic insights for PPCPs that are predominantly or permanently ionized. Targeted experiments across environmentally realistic conditions are needed to address the following questions: (1) What are the partitioning and sorption behaviors of strongly ionizing chemicals among species? (2) How does membrane permeability of ions influence bioaccumulation of PPCPs? (3) To what extent are salts and associated complexes with PPCPs influencing bioaccumulation? (4) How do biotransformation and other elimination processes vary within and among species? (5) Are bioaccumulation modeling efforts currently focused on chemicals and species with key data gaps and risk profiles? Answering these questions promises to address key sources of uncertainty for bioaccumulation modeling of ionizable PPCPs and related contaminants. Environ Toxicol Chem 2024;43:502-512. © 2022 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Effects of water quality on palladium-induced olfactory toxicity and bioaccumulation in rainbow trout (Oncorhynchus mykiss)

Through emission processes, palladium (Pd) particulates from industrial sources are introduced into a range of ecosystems including freshwater environments. Despite this, research on Pd-induced bioaccumulation, uptake, and toxicity is limited for freshwater fishes. Unlike other metals, there are currently no regulations or protective guidelines to limit Pd release into aquatic systems, indicating a global absence of measures addressing its environmental impact. To assess the olfactory toxicity potential of Pd, the present study aimed to explore Pd accumulation in olfactory tissues, olfactory disruption, and oxidative stress in rainbow trout (Oncorhynchus mykiss) following waterborne Pd exposure. Olfactory sensitivity, measured by electro-olfactography, demonstrated that Pd inhibits multiple pathways of the olfactory system following 96 h of Pd exposure. In this study, the concentrations of Pd for inhibition of olfactory function by 20% (2.5 μg/L; IC20) and 50% (19 μg/L; IC50) were established. Rainbow trout were then exposed to IC20 and IC50 Pd concentrations in combination with varying exposure conditions, as changes in water quality alter the toxicity of metals. Independent to Pd, increased water hardness resulted in decreased olfactory perception owing to ion competition at the olfactory epithelium. No other environmental parameter in this study significantly influenced Pd-induced olfactory toxicity. Membrane-associated Pd was measured at the olfactory rosette and gill following exposure; however, this accumulation did not translate to oxidative stress as measured by the production of malondialdehyde. Our data suggest that Pd is toxic to rainbow trout via waterborne contamination near field-measured levels. This study further demonstrated Pd bioavailability and uptake at water-adjacent tissues, adding to our collective understanding of the toxicological profile of Pd. Taken together, our results provide novel insights into the olfactory toxicity in fish following Pd exposure. Integr Environ Assess Manag 2024;00:1-13. © 2024 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals LLC on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Prioritization of chemicals in personal care products based on persistent, bioaccumulative and toxic (PBT) potential: An Indian perspective

Numerous organic ingredients present in Personal care products (PCPs) are being detected in sewage which has a high potential to impact the environment. These compounds are called as Emerging contaminants (ECs) or Contaminants of emerging concern. However, the information on the source and occurrence of ECs present in PCPs is very minimal. Specifically, information on the persistence (P), bioaccumulation (B) and toxicity (T) is very scarce. The determination of PBT properties is a complex task given the magnitude of chemicals, thus it is necessary to have a tool to quickly screen and prioritize the most important compounds. Estimation Program Interface (EPI) Suite™ is one such tool authorized by United States Environmental Protection Agency (US EPA) for screening purposes. In the present study, several organic compounds present in the PCPs viz. body lotion, sunscreens, moisturizers, hair dyes, and some hair care products were identified and their PBT property was estimated. The results from the study indicate that the order of increasing occurrence of PBT chemicals is sunscreens > moisturizers > body lotion > hair care products > hair dyes. The prioritized compounds were given rank 1 (maximum concern) to rank 4 (minimum concern). From the results, the compounds octocrylene in sunscreens and butylphenyl methylpropional in body lotions were prioritized as Rank 1.

In silico bioavailability triggers applied to direct and indirect thyroid hormone disruptors

Among endocrine disruption, interference with the thyroid hormone (TH) regulation is of increasing concern. Respective compounds encode through their structural features both the potential for TH disruption, and the bioavailability mitigating the toxicological effect. The aim of this study is to provide a substructure-based screening-level QSAR (quantitative structure-activity relationship) that discriminates bioavailable TH disruptors from not bioavailable counterparts, covering both direct and indirect (retinoid- and AhR-mediated) modes of action. The QSAR has been derived from literature data for 1642 compounds, and takes into account Lipinski's rule-of-five and the brain/blood partition coefficient Kbrain/blood. For its validation, an external test set of 145 substances has been used. For 1787 compounds meeting the model application domain, the model yields only one false negative. The discussion addresses the mechanistic meaning of the bioavailability triggers molecular weight, H-bond donor and acceptor, hydrophobicity (log Kow), and the physicochemical properties underlying log Kbrain/blood. The model may serve as bioavailability-screening step within a decision support system for the predictive assessment of chemicals regarding their potential to disrupt thyroid hormone function in a direct or indirect manner.

A review on in silico prediction of the environmental risks posed by pharmaceutical emerging contaminants

Computer-aided (in silico) prediction has shown good potential to support the environmental risk assessment (ERA) of pharmaceutical emerging contaminants (PECs), allowing low-cost, animal-free, high-throughput screening of multiple potential risks posed by a wide variety of pharmaceuticals in the environment based on insufficient toxicity data. This review provided recent insights regarding the application of in silico approaches in prediction for environmental risks of PECs. Based on the review of 20 included articles from 8 countries published since 2018, we found that the researchers' interest and concern in this research topic were sharply aroused since 2021. Recently, in silico approaches have been widely used for the prediction of bioaccumulation and biodegradability, lethal endpoints, developmental toxicity, mutagenicity, other eco-toxicological effects such as ototoxicity and hematological toxicity, and human health hazards of exposure to PECs. Particular attention has been given to the simultaneous discernment of multiple environmental risks and health effects of PECs based on mechanistic data of pharmaceuticals using advanced bioinformatic methods such as transcriptomic analysis and network pharmacology prediction. In silico software platforms and databases used in the included studies were diversified, and there is currently no standardized and accepted in silico model for ERA of PECs. Date suggested that in silico prediction of the environmental risks posed by PECs is still in its infancy. Considerable critical challenges need to be addressed, including consideration of environmental exposure concentration for PECs, interactions among mixtures of PECs and other contaminants coexisting in environments, and development of in silico models specific to ERA of PECs.

Systematic computational toxicity analysis of the ozonolytic degraded compounds of azo dyes: Quantitative structure-activity relationship (QSAR) and adverse outcome pathway (AOP) based approach

The present study identifies and analyses the degraded products of three azo dyes (Reactive Orange 16, Reactive Red 120, and Direct Red 80) and proffers their in silico toxicity predictions. In our previously published work, the synthetic dye effluents were degraded using an ozonolysis-based Advanced Oxidation Process. In the present study, the degraded products of the three dyes were analysed using GC-MS at endpoint strategy and further subjected to in silico toxicity analysis using Toxicity Estimation Software Tool (TEST), Prediction Of TOXicity of chemicals (ProTox-II), and Estimation Programs Interface Suite (EPI Suite). Several physiological toxicity endpoints, such as hepatotoxicity, carcinogenicity, mutagenicity, cellular and molecular interactions, were considered to assess the Quantitative Structure-Activity Relationships (QSAR) and adverse outcome pathways. The environmental fate of the by-products in terms of their biodegradability and possible bioaccumulation was also assessed. Results of ProTox-II suggested that the azo dye degradation products are carcinogenic, immunotoxic, and cytotoxic and displayed toxicity towards Androgen Receptor and Mitochondrial Membrane Potential. TEST results predicted LC50 and IGC50 values for three organisms Tetrahymena pyriformis, Daphnia magna, and Pimephales promelas. EPISUITE software via the BCFBAF module surmises that the degradation products' bioaccumulation (BAF) and bioconcentration factors (BCF) are high. The cumulative inference of the results suggests that most degradation by-products are toxic and need further remediation strategies. The study aims to complement existing tests to predict toxicity and prioritise the elimination/reduction of harmful degradation products of primary treatment procedures. The novelty of this study is that it streamlines in silico approaches to predict the nature of toxicity of degradation by-products of toxic industrial affluents like azo dyes. These approaches can assist the first phase of toxicology assessments for any pollutant for regulatory decision-making bodies to chalk out appropriate action plans for their remediation.

Bioaccumulation/bioconcentration of pharmaceutical active compounds in aquatic organisms: Assessment and factors database

There is increasing evidence that the presence of certain pharmaceuticals in the environment leads to biota exposure and constitute a potential risk for ecosystems. Bioaccumulation is an essential focus of risk assessment to evaluate at what degree emerging contaminants are a hazard both to the environment and the individuals that inhabit it. The main goals of the present review are 1) to summarize and describe the research and factors that should be taken into account in the evaluation of bioaccumulation of pharmaceuticals in aquatic organisms; and 2) to provide a database and a critical review of the bioaccumulation/bioconcentration factors (BAF or BCF) of these compounds in organisms of different trophic levels. Most studies fall into one of two categories: laboratory-scale absorption and purification tests or field studies and, to a lesser extent, large-scale, semi-natural system tests. Although in the last 5 years there has been considerable progress in this field, especially in species of fish and molluscs, research is still limited on other aquatic species like crustaceans or algae. This revision includes >230 bioconcentration factors (BCF) and >530 bioaccumulation factors (BAF), determined for 113 pharmaceuticals. The most commonly studied is the antidepressant group, followed by diclofenac and carbamazepine. There is currently no reported accumulation data on certain compounds, such as anti-cancer drugs. BCFs are highly influenced by experimental factors (notably the exposure level, time or temperature). Field BAFs are superior to laboratory BCFs, highlighting the importance of field studies for reliable assessments and in true environmental conditions. BAF data appears to be organ, species and compound-specific. The potential impact on food web transfer is also considered. Among different aquatic species, lower trophic levels and benthic organisms exhibit relatively higher uptake of these compounds.

In vitro biotransformation assays using fish liver cells: Comparing rainbow trout and carp hepatocytes

Biotransformation assays using primary hepatocytes from rainbow trout, Oncorhynchus mykiss, were validated as a reliable in vitro tool to predict in vivo bioconcentration factors (BCF) of chemicals in fish. Given the pronounced interspecies differences of chemical biotransformation, the present study aimed to compare biotransformation rate values and BCF predictions obtained with hepatocytes from the cold-water species, rainbow trout, to data obtained with hepatocytes of the warm-water species, common carp (Cyprinus carpio). In a first step, we adapted the protocol for the trout hepatocyte assay, including the cryopreservation method, to carp hepatocytes. The successful adaptation serves as proof of principle that the in vitro hepatocyte biotransformation assays can be technically transferred across fish species. In a second step, we compared the in vitro intrinsic clearance rates (CL_{in vitro, int}) of two model xenobiotics, benzo[a]pyrene (BaP) and methoxychlor (MXC), in trout and carp hepatocytes. The in vitro data were used to predict in vivo biotransformation rate constants (k_B) and BCFs, which were then compared to measured in vivo k_B and BCF values. The CL_{in vitro, int} values of BaP and MXC did not differ significantly between trout and carp hepatocytes, but the predicted BCF values were significantly higher in trout than in carp. In contrast, the measured in vivo BCF values did not differ significantly between the two species. A possible explanation of this discrepancy is that the existing in vitro-in vivo prediction models are parameterized only for trout but not for carp. Therefore, future research needs to develop species-specific extrapolation models.

Interaction of ionic liquids with human serum albumin in the view of bioconcentration: a preliminary study

Bioaccumulation potential is critical in PBT and risk assessment of chemicals. However, for ionic liquids (ILs), this aspect remains neglected. It is especially important to fill this gap, because for this group of compounds, existing data confirm their risk of being environmentally persistent and toxicity. Moreover, considering preliminary reports on the interactions of ILs with lipids, it may be assumed that ILs have a higher potential for bioaccumulation than indicated by previous estimations built upon octanol–water partition coefficients. Moreover, the bioconcentration of ionizable chemical compounds may also be strongly related to plasma protein contents. Therefore, in this work, the affinity of a set of imidazolium cations and organic anions, and their combination to human serum albumin (HSA) was determined. The obtained results reveal that both cations and anions can be strongly bound to HSA, and blood proteins might play an important role in overall bioaccumulation. Furthermore, it was observed that HSA binding properties towards IL cations depend on the hydrophobicity of cations. The obtained data also provide indication that cation–anion interaction may affect ILs ions affinity to HSA.

Polychlorinated Diphenyl Sulfides: An Emerging Class of Persistent, Bioaccumulative, and Toxic Substances in the Environment

Polychlorinated diphenyl sulfides (PCDPSs) have recently attracted increasing attention due to their potential adverse effects on human and ecosystem health. We present a review regarding their environmental occurrence, persistence, bioaccumulation, toxicity, and biotransformation. The existing literature demonstrates that PCDPSs are ubiquitous in various environmental matrices, are persistent in the environment, and have long-range transport potential. In addition, the high bioaccumulation potential of these emerging pollutants, especially the low chlorinated PCDPS congeners, has been confirmed based on both theoretical calculations and experimental investigations. Moreover, a spectrum of adverse effects, such as acute liver injury, retardation of development, reproductive disorders, and increased mortality have been widely reported in vertebrates. These adverse outcomes were associated with oxidative stress and activation of aryl hydrocarbon receptors. Given these findings, PCDPSs represent candidate persistent, bioaccumulative, and toxic substances and thus deserve further research to fully elucidate their environmental behavior and fate, and evaluate the risks to human and ecosystem health. Environ Toxicol Chem 2021;40:2657-2666. © 2021 SETAC.

Interaction of pharmaceutical metabolites with blood proteins and membrane lipids in the view of bioconcentration: A preliminary study based on in vitro assessment

Pharmaceuticals pose a real threat to the environment, which has been proven in many studies to date. However, still little is known about the transformation products (TPs) of these compounds, which can also interact with organisms, causing adverse effects like noticeable toxicity or bioconcentration. Many recent works confirm that metabolites of pharmaceuticals are present in the environment, and preliminary studies suggest that they may be equally dangerous to or even more so than their parent compounds. Additionally, it has been proven that some of them have high hydrolytic stability, thus they may be persistent in the environment. This property also increases the likelihood that these compounds will be uptaken and accumulated in the tissues of organisms. Therefore, the aim of the present study was to preliminarily estimate the affinity of the transformation products of selected drugs for blood proteins and cell membrane-forming lipids, considered as important sorption phases during distribution in a living organism. In this study, it was shown that although the examined metabolites do not have a strong affinity for membrane lipids, they exhibit relatively strong binding to proteins, which may considerably affect the distribution of TPs in an organism and may indicate a non-classical process of bioconcentration. The results obtained confirm that the TPs of pharmaceuticals should be given much more attention and their potential for bioconcentration should be further determined.

Ionic liquids as environmental hazards - Crucial data in view of future PBT and PMT assessment

Ionic liquids (ILs) constitute a large group of chemical compounds. They have gained much attention among scientists and industry due to their unique properties. Due to the fact that ILs are purely ionic compounds, there is the possibility to design an enormous number of cation and anion combinations, making them designer solvents. Thus it also creates the possibility of producing more environmentally benign solvents. However, significant drawbacks related mainly to their toxicity and persistence have already been noticed. Furthermore the interest in these compounds is constantly growing and their impact on the environment should be defined. More and more ILs are produced or imported in the amount higher than 10 tonnes per year and the group of ILs registered in REACH is still expanding. Thus for an increasing number of compounds, it will be necessary to perform a PBT and PMT assessment using the criteria described in REACH. Therefore the data collected in this work thoroughly sort out the information on the toxicity, bioconcentration/bioaccumulation, biodegradation and mobility of ILs in the context of PBT and PMT assessment.

In Vitro Biotransformation Assays Using Liver S9 Fractions and Hepatocytes from Rainbow Trout (Oncorhynchus mykiss): Overcoming Challenges with Difficult to Test Fragrance Chemicals

In vitro metabolic stability assays using rainbow trout (Oncorhynchus mykiss) isolated hepatocytes (RT-HEP) or hepatic S9 fractions (RT-S9) were introduced to provide biotransformation rate data for the assessment of chemical bioaccumulation in fish. The present study explored the suitability of the RT-HEP and RT-S9 assays for difficult test chemicals, and the in vitro-based predictions were compared to in silico-based predictions and in vivo-measured bioconcentration factors (BCFs). The results show that volatile or reactive chemicals can be tested with minor modifications of the in vitro protocols. For hydrophobic chemicals, a passive dosing technique was developed. Finally, a design-of-experiment approach was used to identify optimal in vitro assay conditions. The modified assay protocols were applied to 10 fragrances with diverse physicochemical properties. The in vitro intrinsic clearance rates were higher in the S9 than in the hepatocyte assay, but the in vitro-in vivo (IVIV) predictions were comparable between the 2 assays. The IVIV predictions classified the test chemicals as nonbioaccumulative (BCF < 2000), which was in agreement with the in vivo data but in contrast to the in silico-based predictions. The findings from the present study provide strong evidence that the RT-HEP and RT-S9 assays can provide reliable estimates of in vivo biotransformation rates for test chemicals with difficult physicochemical properties. Environ Toxicol Chem 2020;39:2396-2408. © 2020 SETAC.

Predicting PBT and CMR properties of substances of very high concern (SVHCs) using QSAR models, and application for K-REACH

•

BIOWIN is effective for predicting persistence and bioaccumulation.

•

Toxtree is effective for predicting carcinogenicity and mutagenicity.

•

WoE approach enhances the sensitivity.

•

It is recommended to set a conservative criteria of log Kow more than 4.5 in K-REACH.

Quantitative structure-activity relationship (QSAR) models have been applied to predict a variety of toxicity endpoints. Their performance needs to be validated, in a variety of cases, to increase their applicability to chemical regulation. Using the data set of substances of very high concern (SVHCs), the performance of QSAR models were evaluated to predict the persistence and bioaccumulation of PBT, and the carcinogenicity and mutagenicity of CMR. BIOWIN and Toxtree showed higher sensitivity than other QSAR models – the former for persistence and bioaccumulation, the latter for carcinogenicity. In terms of mutagenicity, the sensitivities of QSAR models were underestimated, Toxtree was more accurate and specific than lazy structure–activity relationships (LAZARs) and Computer Assisted Evaluation of industrial chemical Substances According to Regulations (CAESAR). Using the weight of evidence (WoE) approach, which integrates results of individual QSAR models, enhanced the sensitivity of each toxicity endpoint. On the basis of obtained results, in particular the prediction of persistence and bioaccumulation by KOWWIN, a conservative criterion is recommended of log Kow greater than 4.5 in K-REACH, without an upper limit. This study suggests that reliable production of toxicity data by QSAR models is facilitated by a better understanding of the performance of these models.

Bioconcentration factors for hydrocarbons and petrochemicals: Understanding processes, uncertainty and predictive model performance

Fish bioconcentration factors (BCFs) are often used to assess substance-specific bioaccumulation. However, reliable BCF data are limited given the practical challenges of conducting such tests. The objectives of this paper are to describe nine rainbow trout studies performed in our lab using tailored dosing and test designs for obtaining empirical BCFs for 21 test substances; gain insights into the structural features and processes determining the magnitude and uncertainty in observed BCFs; and assess performance of six quantitative structure property relationships (QSPRs) for correctly categorizing bioaccumulation given current regulatory triggers. Resulting mean steady-state BCFs, adjusted to a 5% lipid content, ranged from 12 Lkg^-1 for isodecanol to 15,448 Lkg^-1 for hexachlorobenzene which served as a positive control. BCFs for hydrocarbons depended on aromatic and saturated ring configurations and position. Uptake clearances appeared to be modulated by gill metabolism and substance bioavailability, while elimination rates were likely influenced by somatic biotransformation. Current approaches for quantifying uncertainty in experimental BCFs, which take into account only variability in measured fish concentrations, were found to underestimate the true uncertainty in this endpoint with important implications for decision-making. The Vega (KNN/Read-Across) QSPR and Arnot-Gobas model yielded the best model performance when compared to measured BCFs generated in this study.

Predictive models in ecotoxicology: Bridging the gap between scientific progress and regulatory applicability-Remarks and research needs

This paper concludes a special series of 7 articles (4 on toxicokinetic-toxicodynamic [TK-TD] models and 3 on quantitative structure-activity relationship [QSAR] models) published in previous issues of Integrated Environmental Assessment and Management (IEAM). The present paper summarizes the special series articles and highlights their contribution to the topic of increasing the regulatory applicability of effect models. For both TK-TD and QSAR approaches, we then describe the main research needs. The use of TK-TD models for describing sublethal effects must be better developed, particularly through the improvement of the dynamic energy budget (DEBtox) approach. The potential of TK-TD models for moving from lower (molecular) to higher (population) hierarchical levels is highlighted as a promising research line. Some relevant issues to improve the acceptance of QSAR models at the regulatory level are also described, such as increased transparency of the performance assessment and of the modeling algorithms, model documentation, relevance of the chosen target for regulatory needs, and improved mechanistic interpretability. Integr Environ Assess Manag 2019;00:000-000. © 2019 SETAC.

In vitro or not in vitro: a short journey through a long history

The aim of ecotoxicology is to study toxic effects on constituents of ecosystems, with the protection goal being populations and communities rather than individual organisms. In this ecosystem perspective, the use of in vitro methodologies measuring cellular and subcellular endpoints at a first glance appears to be odd. Nevertheless, more recently in vitro approaches gained momentum in ecotoxicology. In this article, we will discuss important application domains of in vitro methods in ecotoxicology. One area is the use of in vitro assays to replace, reduce, and refine (3R) in vivo tests. Research in this field has focused mainly on the use of in vitro cytotoxicity assays with fish cells as non-animal alternative to the in vivo lethality test with fish and on in vitro biotransformation assays as part of an alternative testing strategy for bioaccumulation testing with fish. Lessons learned from this research include the importance of a critical evaluation of the sensitivity, specificity and exposure conditions of in vitro assays, as well as the availability of appropriate in vitro-in vivo extrapolation models. In addition to this classical 3R application, other application domains of in vitro assays in ecotoxicology include the screening and prioritization of chemical hazards, the categorization of chemicals according to their modes of action and the provision of mechanistic information for the pathway-based prediction of adverse outcomes. The applications discussed in this essay may highlight the potential of in vitro technologies to enhance the environmental hazard assessment of single chemicals and complex mixtures at a reduced need of animal testing.