Traffic contribution to polycyclic aromatic hydrocarbons in road dust: A source apportionment analysis under different antecedent dry-weather periods

Polycyclic aromatic hydrocarbons in dust from rural communities around gas flaring points in the Niger Delta of Nigeria: an exploration of spatial patterns, sources and possible risk

Indoor and outdoor dust from three rural communities (Emu-Ebendo, EME, Otu-Jeremi, OTJ, and Ebedei, EBD) around gas flaring points, and a rural community (Ugono Abraka, UGA) without gas flare points, in the Niger Delta of Nigeria, was analysed for the concentrations and distribution of polycyclic aromatic hydrocarbons (PAHs), their sources, and possible health risk resulting from human exposure to PAHs in dust from these rural communities. The PAHs were extracted from the dust with a mixture of dichloromethane/n-hexane by ultrasonication, and purified on a silica gel/alumina packed column. Gas chromatography-mass spectrometry was employed to determine the identity and concentrations of PAHs in the cleaned extracts. The Σ16PAH concentrations in the indoor dust ranged from 558 to 167 000, 6580 to 413 000, and 2350-37 500 μg kg-1 for EME, OTJ and EBD respectively, while those of their outdoor counterparts varied from 347 to 19 700, 15 000 to 130 000, and 1780 to 46 300 μg kg-1 for EME, OTJ and EBD respectively. On the other hand, the UGA community without gas flare points had Σ16PAH concentrations in the range of 444-5260 μg kg-1 for indoor dust, and 154-7000 μg kg-1 for outdoor dust. The lifetime cancer risk values for PAHs in these matrices surpassed the acceptable limit of 10-6 suggesting a potential carcinogenic risk resulting from human exposure to PAHs in indoor and outdoor dust from these rural communities. Principal component analysis suggested that PAH contamination of dust from these communities arises principally from gas flaring, combustion of wood/biomass, and vehicular emissions.

PAHs, PCBs and OCPs in olive oil during the fruit ripening period of olive fruits

Because of their possible carcinogenic effects, it is crucial to determine levels of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in olive oils. However, there are a few studies about these pollutants' levels in olive oils and no other studies reported PAHs, PCBs and OCPs at the same time and during the ripening period of olives in olive oils. A modified clean-up technique was successfully applied for eliminating lipidic components. Additionally, this study does not just report the concentrations of these pollutants but also inspects the sources depending on the actual sampling site. Also, PCBs and OCPs carcinogenic risks in olive oil were reported for the first time in the literature. This study aims to present levels, carcinogenic risks, sources and concentration changes during the ripening period of these pollutants in olive oil. For this purpose, fruit samples for oil extraction were collected between the beginning of the fruit ripening and harvest period. Obtained olive oils from the fruits were extracted and cleaned up using the QuEChERS method. GC-MS and GC-ECD were used for the quantitative analysis of the targeted pollutants. The average concentrations for ∑₁₆PAHs, ∑₃₇PCBs and ∑₁₀OCPs were 222.48 ± 133.76 μg/kg, 58.26 ± 21.64 μg/kg and 25.48 ± 19.55 μg/kg, respectively. During the harvest period, the concentrations were in a decreasing trend. Calculated carcinogenic risks were above acceptable limits for all groups and traffic, wood-coal burning, atmospheric transport and previous uses were the main sources. Results of the source determination indicated that some possible sources could be prevented with regulations and precautions.

Biodegradation performance and diversity of enriched bacterial consortia capable of degrading high-molecular-weight polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are key organic pollutants in the environment that pose threats to the ecosystem and human health. The degradation of high molecular weight (HMW) PAHs by enriched bacterial consortia has been previously studied, while the involved metabolisms and microbial communities are still unclear and warrant further investigations. In this study, five bacterial consortia capable of utilizing different PAHs (naphthalene, anthracene, and pyrene) as the sole carbon and energy sources were enriched from PAH-contaminated soil samples. Among the five consortia, consortium TC exhibited the highest pyrene degradation efficiency (91%) after 19 d of incubation. The degradation efficiency was further enhanced up to 99% by supplementing yeast extract. Besides, consortium TC showed tolerances to high concentrations of pyrene (up to 1000 mg/L) and different heavy metal stresses (including Zn²⁺, Cd²⁺, and Pb²⁺). The dominant genus in consortium TC, GS, and PL showing relatively higher degradation efficiency for anthracene and pyrene was Pseudomonas, whereas consortium PG and GD were predominated by genus Achromobacter and class Enterobacteriaceae, respectively. Consortium TC, as a highly efficient HMW PAH-degrading consortium, could be applied for synergistic biodegradation of HMW PAHs and in situ bioremediation of the sites contaminated with both PAHs and heavy metals.

Impact of particle sizes on health risks and source-specific health risks for heavy metals in road dust

To analyze the impact of particle sizes on sources and related health risks for heavy metals, road dust samples in Beijing were collected and sifted into five particle sizes. The positive matrix factorization (PMF), human health risk assessment model (HHRA), and Monte Carlo simulation were used in the health risk assessment and source apportionment. Results showed that mass of particles < 74 μm occupied about 50% of the total particles, while only 8.48% of the particles were > 500 μm. Mass distribution and concentrations of heavy metals in each particle size changed in temporal. Over 85.00% of carcinogenic risks (CR) were from particles <74 μm, whereas CR from particles >250 μm were ignorable. Sources for health risks in each particle size were traffic exhaust, fuel combustion, construction, and use of pesticides and fertilizers. Proportions of sources to CR differed among particle sizes. Traffic exhaust and fuel combustion contributed over 90% to CR in particles <74 μm, whereas construction contributed the highest (31.68-54.14%) among all sources in particles 74-250 μm. Furthermore, the difference between health risks based on sifted road dust and that based on unsifted road dust was quantitatively analyzed. Source-specific health risk apportionment based on unsifted road dust was not presentative to all particle sizes, and true value of health risks could be over 2.5 times of the estimated value based on unsifted road dust, emphasized the importance of sifting of road dust.

Polycyclic aromatic hydrocarbons in road dusts of a densely populated African city: spatial and seasonal distribution, source, and risk assessment

Road dust is a principal source and depository of polycyclic aromatic hydrocarbons (PAHs) in many urban areas of the world. Hence, this study probed the spatial and seasonal pattern, sources, and related cancer health risks of PAHs in the road dusts sampled at ten traffic intersection (TIs) of a model African city. Mixed PAHs sources were ascertained using the diagnostic ratios and positive matrix factorization (PMF) model. The results showed fluctuations in mean concentrations from 36.51 to 43.04 µg/g. Three-ring PAHs were the most abundant PAHs with anthracene (Anth) ranging from 6.84 ± 1.99 to 9.26 ± 4.42 µg/g being the predominant pollutant in Ibadan. Benzo(k)Fluoranthene (BkF) which is a pointer of traffic emission was the most dominant among the seven carcinogenic PAHs considered, varying from 2.68 ± 0.43 to 4.59 ± 0.48 µg/g. Seasonal variation results showed that PAH concentrations were 20% higher during dry season than rainy season. The seven sources of PAHs identified by PMF model include the following: diesel vehicle exhausts, gasoline combustion, diesel combustion, coal tar combustion, gasoline vehicle exhausts, coal and wood (biomass) combustion, and emissions from unburnt fossil fuels. Employing the incremental lifetime cancer risk (ILCR) model, the city's cancer risk of 5.96E-05 for children and 6.60E-05 for adults were more than the satisfactory risk baseline of ILCR ≤ 10^-6 and higher in adults than in Children.

Distribution, sources and exposure risk of polycyclic aromatic hydrocarbons in soils, and indoor and outdoor dust from Port Harcourt city, Nigeria

In this study, we evaluated the concentrations, composition, sources, and potential risks of polycyclic aromatic hydrocarbons (PAHs) in soils, and indoor and outdoor dust from Port Harcourt city in Nigeria. Gas chromatography-mass spectrometry (GC-MS) was used for the detection and quantification of PAH species in the samples. The concentrations of the US EPA 16 PAHs plus 2-methyl-naphthalene (∑17 PAHs) in soils, and indoor and outdoor dust from Port Harcourt city ranged from 240 to 38 400, 276 to 9130 and 44 to 13 200 μg kg^-1 (dry weight, d.w.) respectively. The PAH concentrations in these matrices followed the sequence: soil > indoor dust > outdoor dust. The composition of PAHs in soils and dust (indoor and outdoor) showed remarkable differences with prominence of 3- and 5-ring PAHs. The estimated carcinogenic risk to the residents arising from exposure to these concentrations of PAHs in soils, and indoor and outdoor dust from Port Harcourt was above the acceptable target cancer risk value of 10^-6. We concluded that these sites require clean-up, remedial actions and implementation of stringent pollution control measures with the intention of reducing the undesirable impacts of PAHs on both the ecosystem and humans.

Impact of Land-Use Types on the Distribution and Exposure Risk of Polycyclic Aromatic Hydrocarbons in Dusts from Benin City, Nigeria

The concentrations of the sixteen United States Environmental Protection Agency polycyclic aromatic hydrocarbons (PAHs) were determined in dusts from different land-use types in Benin City by means of gas chromatography-mass spectrometry. The results obtained were used to assess the ecological and human health risk and to determine the source apportionment. The Ʃ16 PAH concentrations in dusts from Benin City ranged from 230 to 2300 µg kg^-1 for industrial areas, 211-1330 µg kg^-1 for commercial areas, 153-1170 µg kg^-1 for residential areas, and from 216 to 1970 µg kg^-1 for school playgrounds/parks. The ecological risk assessment suggested that the levels of PAHs in dusts from these land-use types are of low-to-moderate risk to organisms. The benzo(a)pyrene carcinogenic potency [BaP_TEQ] (70.5-131 µg kg^-1) and benzo(a)pyrene mutagenic potency [BaP_MEQ] (62.9-122 µg kg^-1) concentrations were below the Canadian soil quality guideline value of 600 µg kg^-1. The incremental lifetime carcinogenic risk (ILCR) arising from exposure of adults and children to PAHs in dusts from Benin City were in the magnitude of 10^-4-10^-2, which exceeded the safe target levels of 10^-6, implying a considerable cancer risk for residents of this city. The PAH source apportionment derived from isomeric ratios and multivariate statistics indicated that burning of biomass, wood, and charcoal, and vehicular traffic were the predominant sources of PAHs in dusts from Benin City.

Temporal variations of levels and sources of health risk associated with heavy metals in road dust in Beijing from May 2016 to April 2018

To analyze the temporal variations of heavy metals, health risk, and source-specific health risk, 24 road dust samples were collected from Beijing in each month in two years. The temporal variations of Hg, Pb, and Ni were higher than other heavy metals. Most heavy metals reached their highest concentrations either in winter or in spring, then the concentrations decreased and reached the lowest values in autumn. Human health risk assessment (HHRA) model showed that As, Cr, and Ni might pose cautionary carcinogenic risk (CR) to children (CR > 10^-6). CR for adults were only 0.15 to 0.19 times of that for children. Four sources were identified based on positive matrix factorization model and HHRA model, they were traffic exhaust, fuel combustion, construction, and use of pesticides and fertilizers. Influenced by the difference of carcinogenicity of heavy metals, traffic exhaust contributed the largest to heavy metals (36.02%, over 42.24% higher than other sources), while contributions of fuel combustion to CR (36.95%) was similar to traffic exhaust (37.17%). Monte-Carlo simulation showed that the 95th percentile of probability density functions of CR posed by Cr and Ni from each source were 9.90 × 10^-5 to 2.64 × 10^-4, posing cautionary carcinogenic risk to children. The seasonal change of CR varied among different sources. CR from use of pesticides and fertilizers in spring was 35.06 times of that in winter, and that from fuel combustion in winter was 1.15-2.40 times of that in other seasons. CR from each source was sensitive to ingestion rate and skin adherence factor.

Characterizing the anthropogenic-induced trace elements in an urban aquatic environment: A source apportionment and risk assessment with uncertainty consideration

The spatial distribution of water quality status, especially in water bodies near intensively urbanized areas, is tightly associated with patterns of human activities. For establishing a robust assessment of the sediment quality in an urban aquatic environment, the source apportionment and risk assessment of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg, and Pb in sediments from an anthropogenic-influenced lake were carried out with considering uncertainties from the analysis methods, random errors in the sample population and the spatial sediment heterogeneity. The distribution analysis of the trace metals with inverse distance weighting-determined method showed that the pollutants were concentrated in the middle and southern areas of the lake. According to the self-organizing map and constrained positive matrix factorization receptor model, agricultural sources (24.8%), industrial and vehicular sources (42.5%), and geogenic natural sources (32.7%) were the primary contributors to the given metals. The geogenic natural had the largest random errors, but the overall result was reliable according to the uncertainty analysis. Furthermore, the stochastic contamination and ecological risk models identified a moderate/considerable contamination level and a moderate ecological risk to the urban aquatic ecosystem. With consideration of uncertainties from the spatial heterogeneity, the contamination level of Hg, and the ecological risk of Cd in had a 20-30% probability of the increase.

Alternative sorption filter materials effectively remove non-particulate organic pollutants from stormwater

Urban runoff contains a mixture of both particulate and non-particulate organic pollutants (OPs). Hydrophobic OPs such as higher petroleum hydrocarbons, phthalates, and polycyclic organic hydrocarbons (PAHs) are not exclusively bound to particles, but also present in runoff in colloidal and truly dissolved forms. These hydrophobic compounds can also form nano- and microsized emulsions that may carry pollutants in stormwater. Hence, it is of great importance to develop treatment technologies such as sorption filters that can remove non-particulate OPs from contaminated stormwater. A pilot plant using column bed-filters of sand as a pre-filter, in combination with granulated activated carbon, Sphagnum peat or Pinus sylvestris bark, was used to investigate the removal of non-particulate OPs from urban stormwater. Samples from the filter effluents were collected weekly; during or after rain events; and during stress tests when incoming water was spiked with contaminated sediment and petrol or diesel. All sorption filters showed efficient reduction of aliphatic diesel hydrocarbons C₁₆-C₃₅, benzene, and the PAHs phenanthrene, fluoranthene, and pyrene during most of the operation time, which was 18 months. During the stress test events, all sorption filters showed 100% reduction of PAH-16, petrol and diesel aliphatics C₅-C₃₅. All sorption filters released DOC and nanoparticles, which may explain some of the transportation of OPs through the filter beds. The recommendation is to use a combination of sand pre-filtration and all the studied sorption materials in stormwater filters in series, to achieve effective removal of different types of OPs. It is also important to improve the hydraulic conditions to obtain sufficient water flows through the filters.

Nationwide health risk assessment of juvenile exposure to polycyclic aromatic hydrocarbons (PAHs) in the water body of Chinese lakes

The high emissions of polycyclic aromatic hydrocarbons (PAHs) pose a serious threat to the lake ecosystem and human health, and the human health risk assessment of PAH exposure is expected as an urgent project in China. This paper focused on 44 Chinese lakes in 6 lake zones to investigate the occurrence, composition and source of 19 PAHs in water body and estimate the human health risk under PAH exposure. The "List of PAH Priority Lakes" in China was generated based on the combination of incremental lifetime cancer risk (ILCR) model and Monte Carlo simulation. Our results showed that the Σ₁₇ PAHs ranged from 3.75 ng·L^-1 to 368.68 ng·L^-1 with a median of 55.88 ng·L^-1. Low-ring PAHs were the predominant compounds. PAH profiles varied significantly at lake zone level. Diagnostic ratios showed that PAHs might derive from petroleum and coal or biomass combustion. Benzo[a]pyrene-equivalent toxic concentrations (BaPeq) of the Σ₁₇ PAHs ranged from 0.07 ng·L^-1 to 2.26 ng·L^-1 (0.62 ± 0.52 ng·L^-1, mean ± standard deviation) with a median of 0.47 ng·L^-1. Benzo[a]anthracene (BaA), benzo[a]pyrene (BaP) and benzo[e]pyrene (BeP) were the main toxic isomers. Juvenile exposure to PAHs via oral ingestion (drinking) and dermal contact (showering) had negligible and potential health risks, respectively. Juveniles were the sensitive population for PAH exposure. 15 lakes were screened into the "List of PAH Priority Lakes" in three priority levels: first priority (Level A), moderate priority (Level B) and general priority (Level C). Lake Taihu, Lake Chaohu and Lake Hongze were the extreme priority lakes. Optimizing the economic structures and reducing the combustion emissions in these areas should be implemented to reduce the population under potential health risk of PAHs.

Levels, spatial distribution, and source identification of airborne environmentally persistent free radicals from tree leaves

Environmentally persistent free radicals (EPFRs) are receiving increasing concern due to their toxicity and ubiquity in the environment. To avoid restrictions imposed when using a high-volume active sampler, this study uses tree leaves to act as passive samplers to investigate the spatial distribution characteristics and sources of airborne EPFRs. Tree leaf samples were collected from 120 sites in five areas around China (each approximately 4 km × 4 km). EPFR concentrations in particles (<2 μm) on the surface of 110 leaf samples were detected, ranging from 7.5 × 10¹⁶ to 4.5 × 10¹⁹ spins/g. For the 10 N.D. samples, they were all collected from areas inaccessible by vehicles. The g-values of EPFRs on 68% leaf samples were larger than 2.004, suggesting the electron localized on the oxygen atom, and they were consistent with the road dust sample (g-value: 2.0042). Significant positive correlation was found between concentrations of elemental carbon (tracer of vehicle emissions) and EPFRs. Spatial distribution mapping showed that EPFR levels in various land uses differed noticeably. Although previous work has linked atmospheric EPFRs to waste incineration, the evidence in this study suggests that vehicle emissions, especially from heavy-duty vehicles, are the main sources. While waste incinerators with low emissions or effective dust-control devices might not be an important EPFR contributor. According to our estimation, over 90% of the EPFRs deposited on tree leaves might be attributed to automotive exhaust emissions, as a synergistic effect of primary exhausts and degradation of aromatic compounds in road dust. With adding the trapping agent into the particle samples (<2 μm), signals of hydroxyl radicals were observed. This indicates that EPFRs collected from this phytosampling method can lead to the release of reactive oxygen species (ROS) once they are inhaled by human beings. Thus, this study helps highlight EPFR "hotspots" for potential health risk identification.

Organic pollutants, nano- and microparticles in street sweeping road dust and washwater

Road areas are pollution hotspots where many metals, organic pollutants (OPs) and nano/microparticles accumulate before being transported to receiving waters. Particles on roads originate from e.g. road, tyre and vehicle wear, winter road maintenance, soil erosion, and deposition. Street sweeping has the potential to be an effective and affordable practice to reduce the occurrence of road dust, and thereby the subsequent spreading of pollutants, but there is currently little knowledge regarding its effectiveness. In this paper we investigate the potential of street sweeping to reduce the amounts of OPs and nano/microparticles reaching stormwater, in a case study sampling road dust and washwater from a street sweeping machine, road dust before and after sweeping, and stormwater. The compound groups generally found in the highest concentrations in all matrices were aliphatics C₅-C₃₅ > phthalates > aromatics C₈-C₃₅ > PAH-16. The concentrations of aliphatics C₁₆-C₃₅ and PAHs in washwater were extremely high at ≤ 53,000 µg/L and ≤ 120 µg/L, respectively, and the highest concentrations were found after a 3-month winter break in sweeping. In general, fewer aliphatic and aromatic petroleum hydrocarbons and PAHs were detected in road dust samples than in washwater. The relative composition of the specific PAH-16 suggests tyre wear, vehicle exhausts, brake linings, motor oils and road surface wear as possible sources. The study indicates that many of the hydrophobic compounds quantified in washwater are attached to small particles or truly dissolved. The washwater contains a wide range of small particles, including nanoparticles in sizes from just below 1 nm up to 300 nm, with nanoparticles in the size range 25-300 nm present in the highest concentrations. The results also indicated agglomeration of nanoparticles in the washwater. The street sweeping collected a large amount of fine particles and associated pollutants, leading to the conclusion that washwater from street sweeping needs to be treated before disposal.

Measuring performance of low impact development practices for the surface runoff management

Continuous urbanization over the last few years has led to the increase in impervious surfaces and stormwater runoff. Low Impact Development (LID) is currently receiving increased attention as a promising strategy for surface runoff management. To analyze the performance of LID practices for surface runoff management, a long-term hydrological modeling from 2001 to 2015 along with a cost-effectiveness analysis were carried out on a campus in Dresden, Germany. Seven LID practices and six precipitation scenarios were designed and simulated in a Storm Water Management Model (SWMM). A cost-effectiveness analysis was conducted by calculating the life-cycle costs and runoff removal rate of LID practices. Results demonstrated that the LID practices significantly contributed to surface runoff mitigation in the study area. The LID performance was primarily affected by the length of the precipitation scenarios and LID implementing schemes. The runoff removal rate of the LID practices fluctuated significantly when the rainfall scenario was shorter than 12 months. When the rainfall scenario exceeded 1 year the effects on the runoff removal rate was constant. The combination of an infiltration trench, permeable pavement, and rain barrel (IT ​+ ​PP ​+ ​RB), was the best runoff control capacity with a removal rate ranging from 23.2% to 27.4%. Whereas, the rain barrel was the most cost-effective LID option with a cost-effectiveness (C/E) ratio ranged from 0.34 to 0.41. The modeling method was improved in this study by conducting long-term hydrological simulations with different durations rather than short-term simulations with single storms. In general, the methods and results of this study provided additional improvements and guidance for decision-making process regarding the implementation of appropriate LID practices.

Potential sources and health risk assessment of polycyclic aromatic hydrocarbons in street dusts of Karaj urban area, northern Iran

In the present study chemical fingerprinting approach (isomeric ratios), a receptor-oriented model (principal component analysis with multiple linear regression, PCA/MLR) and a probabilistic health risk framework were employed to characterization, source appointment and carcinogenic risk assessment of polycyclic aromatic hydrocarbons (PAHs) in street dusts of Karaj urban area (northern Iran). Thirty street dusts samples were collected from the different functional areas in the city of Karaj and analyzed for PAHs by gas chromatography/mass spectrometry (GS/MS). The results obtained showed that ∑16PAHs concentrations varied widely from 16.2 to 1236.2 with a mean of 624 μg/kg and decreased in the following order of functional areas; traffic> residential > green/park areas. PAHs profile in the majority of dust samples were dominated by 5-6 rings PAHs, accounting for 25%-95% of the total PAHs. Qualitative source apportionment using the molecular isomeric ratios indicated mixed sources of PAHs in street dusts while PCA/MLR receptor model quantitatively identified three major sources with following relative contributions to the total dust PAH burden; 51% for pyrogenic-traffic sources, 32% for traffic-stationary sources and, 16% for petrogenic sources. The results of health risk assessment based on probabilistic model indicated that at the 95% percentiles, total cancer risks for children and adults are 8.43 × 10^-4 and 3.34 × 10^-5, respectively which both are higher than the acceptable baseline (10^-6) indicating potential carcinogenic risk for local residents. It was also revealed that dust ingestion pathway is the most important contributor to the total carcinogenic risks of PAHs for both children and adults although the cancer risk level for adults through dermal and inhalation was 10 times greater than that for children. Based on the sensitivity analysis using the Monte Carlo simulation, benzo[a]pyrene equivalent concentration, exposure duration, dermal exposure area and ingestion rate were found to be the most sensitive exposure parameters which could introduce uncertainties into the cancer risk estimated.

Road dust contamination by polycyclic aromatic hydrocarbons and their methylated derivatives in northern Vietnam: Concentrations, profiles, emission sources, and risk assessment

Concentrations of unsubstituted and methylated polycyclic aromatic hydrocarbons (PAHs and Me-PAHs) were examined in road dusts from some representative areas with different land-use types in northern Vietnam, providing updated information about the occurrence, sources, and risks of these pollutants in Southeast Asian region. The Vietnamese road dusts were contaminated with low to moderate levels of PAHs and Me-PAHs as compared to those from other countries in the world. Concentrations of PAHs and Me-PAHs (Σ34PAHs) decreased in the order: urban (median 1800; range 1100-5500) ≈ industrial (1300; 550-10,000) > suburban (450; 310-1300) ≈ rural road dust (330; 210-2300 ng g^-1), suggesting an urban-rural declining trend and effects of urbanization-industrialization processes in PAH emission extent in Vietnam. The profiles and diagnostic ratios of PAHs and Me-PAHs in our samples revealed that these compounds were mainly derived from pyrogenic sources rather than petrogenic sources. Traffic emissions (e.g., vehicle exhaust, tire debris, and possible leaks of fuels, oils, and lubricants) were estimated as principal sources of PAHs and Me-PAHs, especially in the urban and industrial areas. Other pyrogenic sources (e.g., coal, wood, and biomass combustion) were also existed in the industrial, suburban, and rural areas, reflecting PAH origins from thermal industrial processes, open burning of agricultural by-products, and domestic energy utilization. Persons working outdoors and children in the urban and industrial areas were estimated to receive higher intake doses of PAHs and Me-PAHs, which were one to two orders of magnitude higher than those estimated for other groups. Except for potential cancer risk estimated for the occupational groups in the industrial area under the worst exposure scenarios, the non-cancer and cancer risk levels were generally acceptable; however, more comprehensive risk assessment considering other exposure pathways (e.g., inhalation and diet) is needed.

Comparative toxicity of organic mixture attached to road deposited sediments: Inadequacy of conventionally using individual pollutants to assess comprehensive hazard effects

Organic pollutants attached on road deposited sediments (RDS) during dry days can be washed-off into stormwater runoff during rainfall events, undermining stormwater reuse safety. Previous research studies commonly utilized individual pollutant groups and their quantity to evaluate the hazard effect of pollutants attached to RDS in terms of stormwater reuse. Since many types of organic pollutants are present together rather than individually, conventional approaches might not permit a comprehensive understanding of how appropriately the RDS polluted stormwater can be reused. This study undertook a toxicity test of organic pollutants attached to RDS using Chinese hamster ovary cells (CHO), testing a hypothesis that solely focusing on individual pollutant groups are not adequate to represent hazard effects of resulting stormwater and hence their adequacy for reuse. It is noted that comparative toxicity of RDS is not strongly related to total solids (commonly seen as the key carrier of pollutants) and chemical oxygen demand (COD, representing organic matters). Additionally, the comparison results of spatial distributions of toxicity (in this study) and individual pollutants in previous studies did not show a similar trend. These results imply that toxicity should be also used to indicate how stormwater can be safely reused while solely investigating individual pollutants can not adequately show a comprehensive hazard effect in terms of ensuring stormwater reuse safety. Based on study outcomes, a new assessment approach considering both pollutant and toxicity were proposed. This will assist on effective stormwater reuse and ensuring their reuse safety.