Are pharmaceuticals removal and membrane fouling in electromembrane bioreactor affected by current density?

Pharmaceuticals removal from hospital wastewater by fluidized aerobic bioreactor in combination with tubesettler

Micropollutants, especially pharmaceutical compounds, are of significant concern owing to their ngL- 1 to µgL- 1 concentration, making them difficult for conventional treatment plants to remove from wastewater. Despite municipal wastewater treatment plant being a primary source of these compounds to be released into the wastewater, on comparison little attention has been given to hospital wastewater. The major focus of studies addressing pharmaceutical compounds is based on synthetic wastewater. This study addresses this research gap by treating wastewater to remove micropollutants (Fluvastatin, ketoprofen, paracetamol, ciprofloxacin, carbamazepine, sulfamethoxazole, and lorazepam) by employing a fluidized aerobic bioreactor. Tubesettler was attached to a fluidized-bed bioreactor to see if it could be used as a polishing unit rather than a secondary clarifier. The environmental risk from the effluent discharge into the environment was assessed regarding the hazard quotient. The paracetamol and ketoprofen were removed at an efficiency of 51% and 60%, respectively, followed by carbamazepine at 50%, ciprofloxacin at 40%, fluvastatin at 47%, sulfamethoxazole at 31%, and lorazepam at 20%. The influent posed moderate environmental risk with (Hazard Quotient) HQ > 0.5, while in effluent the risk was reduced with HQ value 0.4. For effluent from fluidized bed bioreactors (HQ 0.13) and tube setters (HQ 0.15). The associated tube settler was found suitable for polishing units with additional removal efficiencies of 15-43% for all the targeted pharmaceutical compounds. Further studies are required to explore disinfectants' effect on the reactor's biodegradation efficiency. Also, further modification and a hybrid version of the fluidized bed bioreactor can be used.

Sustainable control of microplastics in wastewater using the electrochemically enhanced living membrane bioreactor

Wastewater treatment plant (WWTP) discharges are major contributors to the release of microplastics (MPs) into the environment. This research work aimed to assess the performance of the novel living membrane bioreactor (LMBR), which utilizes a biological layer as a membrane filter for the removal of polyethylene (PE) MPs from wastewater. The impact of an intermittently applied low current density (0.5 mA/cm2) on the reduction of MPs in the electrochemically enhanced LMBR (e-LMBR) has also been examined. The reactors were also compared to a conventional membrane bioreactor (MBR) and an electro-MBR (e-MBR). 1H nuclear magnetic resonance spectroscopy (1H NMR) was implemented for the MPs detection and quantification in terms of mass per volume of sample. The LMBR and MBR achieved comparable mean PE MPs reduction at 95% and 96%, respectively. The MPs mass reduction in the e-LMBR slightly decreased by 2% compared to that achieved in the LMBR. This potentially indicated the partial breakdown of the MPs due to electrochemical processes. Decreasing and inconsistent NH4-N and PO4-P removal efficiencies were observed over time due to the addition of PE MPs in the MBR and LMBR. In contrast, the integration of electric field in the e-MBR and e-LMBR resulted in consistently high values of conventional contaminant removals of COD (99.72-99.77 %), NH4-N (97.96-98.67%), and PO4-P (98.44-100.00%), despite the MPs accumulation. Integrating electrochemical processes in the e-LMBR led to the development of a stable living membrane (LM) layer, as manifested in the consistently low effluent turbidity 0.49 ± 0.33 NTU. Despite the increasing MPs concentration in the mixed liquor, applying electrochemical processes reduced the fouling rates in the e-LMBR. The e-LMBR achieved comparable efficiencies in contaminant reductions as those observed in the e-MBR, while using a low-cost membrane material.

Treatment of azo dye-containing wastewater in a combined UASB-EMBR system: Performance evaluation and membrane fouling study

This work investigated the treatment of azo dye-containing wastewater in an upflow anaerobic sludge blanket (UASB) reactor combined with an electro-membrane bioreactor (EMBR). Current densities of 20 A m-2 and electric current exposure mode of 6'ON/30'OFF were applied to compare the performance of the EMBR to a conventional membrane bioreactor (MBR). The results showed that dye (Drimaren Red CL-7B) removal occurred predominantly in the UASB reactor, which accounted for 57% of the total dye removal achieved by the combined system. When the MBR was assisted by electrocoagulation, the overall azo dye removal efficiency increased from 60.5 to 67.1%. Electrocoagulation batch tests revealed that higher decolorization rates could be obtained with a current density of 50 A m-2. Over the entire experimental period, the combined UASB-EMBR system exhibited excellent performance in terms of chemical oxygen demand (COD) and NH4+-N removal, with average efficiencies above 97%, while PO43--P was only consistently removed when the electrocoagulation was used. Likewise, a consistent reduction in the absorption spectrum of aromatic amines was observed when the MBR was electrochemically assisted. In addition to improving the pollutants removal, the use of electrocoagulation reduced the membrane fouling rate by 68% (0.25-0.08 kPa d-1), while requiring additional energy consumption and operational costs of 1.12 kWh m-3 and 0.32 USD m-3, respectively. Based on the results, it can be concluded that the combined UASB-EMBR system emerges as a promising technological approach for textile wastewater treatment.

Mechanisms and Strategies of Advanced Oxidation Processes for Membrane Fouling Control in MBRs: Membrane-Foulant Removal versus Mixed-Liquor Improvement

Membrane bioreactors (MBRs) are well-established and widely utilized technologies with substantial large-scale plants around the world for municipal and industrial wastewater treatment. Despite their widespread adoption, membrane fouling presents a significant impediment to the broader application of MBRs, necessitating ongoing research and development of effective antifouling strategies. As highly promising, efficient, and environmentally friendly chemical methods for water and wastewater treatment, advanced oxidation processes (AOPs) have demonstrated exceptional competence in the degradation of pollutants and inactivation of bacteria in aqueous environments, exhibiting considerable potential in controlling membrane fouling in MBRs through direct membrane foulant removal (MFR) and indirect mixed-liquor improvement (MLI). Recent proliferation of research on AOPs-based antifouling technologies has catalyzed revolutionary advancements in traditional antifouling methods in MBRs, shedding new light on antifouling mechanisms. To keep pace with the rapid evolution of MBRs, there is an urgent need for a comprehensive summary and discussion of the antifouling advances of AOPs in MBRs, particularly with a focus on understanding the realizing pathways of MFR and MLI. In this critical review, we emphasize the superiority and feasibility of implementing AOPs-based antifouling technologies in MBRs. Moreover, we systematically overview antifouling mechanisms and strategies, such as membrane modification and cleaning for MFR, as well as pretreatment and in-situ treatment for MLI, based on specific AOPs including electrochemical oxidation, photocatalysis, Fenton, and ozonation. Furthermore, we provide recommendations for selecting antifouling strategies (MFR or MLI) in MBRs, along with proposed regulatory measures for specific AOPs-based technologies according to the operational conditions and energy consumption of MBRs. Finally, we highlight future research prospects rooted in the existing application challenges of AOPs in MBRs, including low antifouling efficiency, elevated additional costs, production of metal sludge, and potential damage to polymeric membranes. The fundamental insights presented in this review aim to elevate research interest and ignite innovative thinking regarding the design, improvement, and deployment of AOPs-based antifouling approaches in MBRs, thereby advancing the extensive utilization of membrane-separation technology in the field of wastewater treatment.

Electro living membrane bioreactor for highly efficient wastewater treatment and fouling mitigation: Influence of current density on process performances

The next generation of the self-forming dynamic membrane, referred to in this study as the "Living Membrane (LM)", is a new patented technology based on an encapsulated biological layer that self-forms on a designed coarse-pore size support material during wastewater treatment and acts as a natural membrane filter. Integrating electrochemical processes with wastewater treatment using the LM approach has also been recently studied (the reactor is referred to as the Electro-Living Membrane Bioreactor or e-LMBR). This study investigated the effects of varying current densities, i.e., 0.3, 0.5, and 0.9 mA/cm2, on the performance of an e-LMBR. The results were also compared with those of the Living Membrane Bioreactor or LMBR (without applied current density). Higher pollutant removals were observed in the presence of the electric field. However, the effect of varying applied current densities on the COD (98-99 %), NH3-N (97-99 %), and PO43-P (100 %) removals was not statistically significant. The more prominent differences (p < 0.05) were observed in the decrease of NO3--N concentrations from mixed liquor to effluent, with increasing current density resulting in lower mean NO3--N effluent concentrations (0.3 mA/cm2: 6.13 mg/L; 0.5 mA/cm2: 4.38 mg/L; 0.9 mA/cm2: 3.70 mg/L). The reduction of NO3--N concentrations as wastewater permeated through the LM layer also confirmed its role in removing nitrogen-containing compounds. Higher current densities resulted in lower concentrations of fouling substances, particularly those of microbial extracellular polymeric substances (EPS) and transparent exopolymer particles (TEPs). The average values of the temporal variation of transmembrane pressure (d(TMP)/d(t)) in the e-LMBR were extremely low, in the range of 0.013-0.041 kPa/day, throughout the operation period. The highest (d(TMP)/d(t)) was observed for the highest current density. However, the TMP values remained below 2 kPa in all the e-LMBR runs even after the initial LM formation stage.

Recent perspective of antibiotics remediation: A review of the principles, mechanisms, and chemistry controlling remediation from aqueous media

Antibiotic pollution is an ever-growing concern that affects the growth of plants and the well-being of animals and humans. Research on antibiotics remediation from aqueous media has grown over the years and previous reviews have highlighted recent advances in antibiotics remediation technologies, perspectives on antibiotics ecotoxicity, and the development of antibiotic-resistant genes. Nevertheless, the relationship between antibiotics solution chemistry, remediation technology, and the interactions between antibiotics and adsorbents at the molecular level is still elusive. Thus, this review summarizes recent literature on antibiotics remediation from aqueous media and the adsorption perspective. The review discusses the principles, mechanisms, and solution chemistry of antibiotics and how they affect remediation and the type of adsorbents used for antibiotic adsorption processes. The literature analysis revealed that: (i) Although antibiotics extraction and detection techniques have evolved from single-substrate-oriented to multi-substrates-oriented detection technologies, antibiotics pollution remains a great danger to the environment due to its trace level; (ii) Some of the most effective antibiotic remediation technologies are still at the laboratory scale. Thus, upscaling these technologies to field level will require funding, which brings in more constraints and doubts patterning to whether the technology will achieve the same performance as in the laboratory; and (iii) Adsorption technologies remain the most affordable for antibiotic remediation. However, the recent trends show more focus on developing high-end adsorbents which are expensive and sometimes less efficient compared to existing adsorbents. Thus, more research needs to focus on developing cheaper and less complex adsorbents from readily available raw materials. This review will be beneficial to stakeholders, researchers, and public health professionals for the efficient management of antibiotics for a refined decision.

Super-adsorbent microspheres based on a triallyl isocyanurate-maleic anhydride copolymer for the removal of organic pollutants from water

Owing to the frequent occurrence of diclofenac sodium (DS) in fresh aquatic environments and its potential toxicity towards living organisms, the effective removal of DS has attracted worldwide attention. Herein, a green and efficient strategy to fabricate crosslinked microspheres with interconnected mesoporous structures and abundant adsorption active sites was developed. With this strategy, triallyl isocyanurate (TAIC)-maleic anhydride (MAH) copolymer microspheres (TMs) with a diameter of 1.19-1.35 μm were first prepared by self-stabilized precipitation (2SP) polymerization, and the TMs possess a large amount reactive anhydride groups (62.5-71.8 mol%), a specific surface area of 51.6-182.4 m² g^-1 and a mesoporous structure (average pore size: 3.4-3.8 nm). Then the TMs were further functionalized with polyethylenimine (PEI) to give rise to cationic microspheres (Cat-TMs), which showed excellent adsorption performance to DS with a rapid adsorption rate (reached equilibrium within 30 min), a very high equilibrium adsorption capacity (1421 mg g^-1) and excellent recyclability. The pseudo-second-order model and Langmuir model were a good fit for the adsorption kinetic and isotherm process, respectively. Furthermore, due to the high cation density (4.291 mmol g^-1) and excellent pH buffer capacity of Cat-TMs, the adsorption capacity can be maintained at a high level within the pH range of 6-10. The regenerated Cat-TMs showed only a slight loss (<5%) in the adsorption capacity even after 5 adsorption-desorption cycles. In short, Cat-TMs can be considered as a highly promising adsorbent for the rapid and ultra-efficient removal of anionic organic contaminants and have significant potential to be applied in wastewater treatment.

Exploration of the effect of simultaneous removal of EDCs in the treatment process of different types of wastewater

The SPE-HPLC-MS/MS method was used to investigate the concentration distribution of nine types of estrogens in 18 locations of pollution source along the Jiuzhou River belonging to river systems in Guangdong province and Guangxi Zhuang autonomous region in China, and the estrogenic activity and potential ecological risks were evaluated by calculating the estradiol equivalency (EEQ). The results showed that the calculated estradiol equivalents (cEEQs) of wastewater treatment plants from 17 locations were all higher than 1 ng/L. To further study the removal effect of the treatment process on the estrogens, the pig breeding wastewater from P4 and the municipal wastewater from P13, as well as the black-odorous water, were sampled and surveyed during the entire process. It turned out that estrogens were effectively removed after nitrification activated sludge treatment. Meanwhile, there was a positive correlation between the removal of NH₃-N, total nitrogen (TN) and total phosphorus (TP) and the removal of endocrine disrupting chemicals (EDCs). It is shown in the study the secondary treatment process has achieved a significant effect on the removal of estrogen in both the wet and dry periods and that there has been a positive correlation between the activities of total phosphorus compounds, nitrogen-based compounds and the removal of EDCs.

Anaerobic membrane bioreactors for pharmaceutical-laden wastewater treatment: A critical review

Pharmaceuticalsare a diverse group of chemical compounds widely used for prevention and treatment of infectious diseases in both humans and animals. Pharmaceuticals, either in their original or metabolite form, find way into the wastewater treatment plants (WWTPs) from different sources. Recently, anaerobic membrane bioreactors (AnMBR) has received significant research attention for the treatment of pharmaceuticals in various wastewater streams. This review critically examines the behaviour and removal of a wide array of pharmaceuticals in AnMBR with primary focus on their removal efficiencies and mechanisms, critical influencing factors, and the microbial community structures. Subsequently, the inhibitory effects of pharmaceuticals on the performance of AnMBR and membrane fouling are critically discussed. Furthermore, the imperative role of membrane biofouling layer and its components in pharmaceuticals removal is highlighted. Finally, recent advancements in AnMBR configurations for membrane fouling control and enhanced pharmaceuticals removal are systemically discussed.

A review on advances in removal of endocrine disrupting compounds from aquatic matrices: Future perspectives on utilization of agri-waste based adsorbents

In the recent past, a class of emerging contaminants particularly endocrine disrupting compounds (EDCs) in the aquatic environment have gained a lot of attention. This is due to their toxic behaviour, affecting endocrine activities in humans as well as among aquatic animals. Presently, there are no regulations and discharge limits for EDCs to preclude their negative impact. Furthermore, the conventional treatment processes fail to remove EDCs efficiently. This necessitates the need for more research aimed at development of advanced alternative treatment methods which are economical, efficient, and sustainable. This paper focusses on the occurrence, fate, toxicity, and various treatment processes for removal of EDCs. The treatment processes (physical, chemical, biological and hybrid) have been comprehensively studied highlighting their advantages and disadvantages. Additionally, the use of agri-waste based adsorption technologies has been reviewed. The aim of this review article is to understand the prospect of application of agri-waste based adsorbents for efficient removal of EDCs. Interestingly, research findings have indicated that the use of these low-cost and abundantly available agri-waste based adsorbents can efficiently remove the EDCs. Furthermore, the challenges and future perspectives on the use of agri-waste based adsorbents have been discussed.

Effective leachate treatment by a pilot-scale submerged electro-membrane bioreactor

Most landfill leachates contain organic compounds that cannot be easily separated by conventional biological processes. Recently, integration of membrane bioreactors and electro-oxidation has been proposed as a suitable option for the treatment and separation of organic and inorganic contaminants in leachate. Therefore, in the present study, the performance of submerged electro-membrane bioreactor (SEMBR) along with a conventional membrane bioreactor (MBR) on a pilot scale was evaluated for the treatment of leachate. Both bioreactors were used to compare treatment efficiency under the same conditions. The removal rates of chemical oxygen demand (COD), ammonia nitrogen (NH₄⁺-N), phosphate (PO₄^3--P), color, UV₂₅₄, and metals were investigated. The results showed that applying electric current to the MBR could approximately increase the COD removal efficiency from 94 to 98.5%; PO₄^3--P removal from 70 to 99%; NH₃⁺-N removal from 91 to 99%; UV₂₅₄ removal from 80 to 96%; and heavy metals removal from 40 to 95%. Humic acid removal efficiency as another indicator of humic substances was increased from 75% in the MBR to 96% in the SEMBR process. The results also showed that the effluent can be introduced into the wastewater treatment plant for further treatment. The SEMBR process achieved a minimization of fouling of membranes compared to conventional MBR. The consumption of the energy and electrode was in accordance with the previous results, and the required energy of 1.57 kWh/m³ of wastewater was calculated. The sludge volume index (SVI) in SEMBR (105 ml/g) was better than MBR (135 ml/g) due to the electrokinetic effect on the production of denser flocs. Based on the results, it can be concluded that the application of electric current can improve the performance of MBR in removing PO₄^3-, NH₄⁺, and membrane fouling.

Innovative encapsulated self-forming dynamic bio-membrane bioreactor (ESFDMBR) for efficient wastewater treatment and fouling control

The concept of a novel living encapsulated self-forming dynamic bio-membranes (ESFDM) for an innovative wastewater treatment in membrane bioreactor (MBR) is presented in the current study. The active filtering membrane is encapsulated, and thus stabilized, between two support meshes with pore in micrometer size. The combination of activated sludge, the ESFDM and the cake layer formed external to the filtering module contributed to the treatment of municipal wastewater. COD concentration reductions (average value of 95.55 ± 1.44%) by ESFDM bioreactor (ESFDMBR) were comparable to those obtained with a previously reported membrane bioreactor (MBR), where a conventional membrane was studied under the same operating conditions. The ESFDMBR, compared to the conventional MBR, obtained higher reductions of NH₃-N, NO₃^-N and PO₄^3-P concentrations. Increased removals of nitrogen-containing nutrients were ascribed to anoxic conditions reached in the ESFDM layer protected from the aeration by the external cake layer. Rate of increase of transmembrane pressure (TMP) per day in the ESFDMBR (0.03 kPa/day) was lower than the value obtained in the previously reported conventional MBR (8.08 kPa/day). Lower concentrations of fouling precursors in combination with the effective filtration capacity of the porous living ESFDM resulted in the reduction of the fouling rate. Analysis of microbiological community revealed that the microbial community structures in the mixed liquor and ESFDM were different. The ESFDM layer promoted growth of bacteria as indicated by the higher total cell count and higher microbial diversity compared to those observed in the mixed liquor.

Wastewater treatment and fouling control in an electro algae-activated sludge membrane bioreactor

The effect of addition of algae to activated sludge as active biomass in membrane bioreactors (MBRs) and electro-MBRs (e-MBRs) for wastewater remediation was examined in this study. The performances of Algae-Activated Sludge Membrane Bioreactor (AAS-MBR) and electro Algae-Activated Sludge Membrane Bioreactor (e-AAS-MBR) were compared to those observed in conventional MBR and e-MBR, which were previously reported and utilized activated sludge as biomass. The effect of application of electric field was also examined by the comparison of performances of e-AAS-MBR and AAS-MBR. Similar chemical oxygen demand (COD) reduction efficiencies of AAS-MBR, e-AAS-MBR, MBR, and e-MBR (98.35 ± 0.35%, 99.12 ± 0.08%, 97.70 ± 1.10%, and 98.10 ± 1.70%, respectively) were observed. The effect of the algae-activated sludge system was significantly higher in the nutrient removals. Ammoniacal nitrogen (NH₃-N) removal efficiencies of AAS-MBR and e-AAS-MBR were higher by 43.89% and 26.61% than in the conventional MBR and e-MBR, respectively. Phosphate phosphorous (PO₄^3--P) removals were also higher in AAS-MBR and e-AAS-MBR by 6.43% and 2.66% than those in conventional MBR and e-MBR. Membrane fouling rates in AAS-MBR and e-AAS-MBR were lower by 57.30% and 61.95% than in MBR and e-MBR, respectively. Lower concentrations of fouling substances were also observed in the reactors containing algae-activated sludge biomass. Results revealed that addition of algae improved nutrient removal and membrane fouling mitigation. The study also highlighted that the application of electric field in the e-AAS-MBR enhanced organic contaminants and nutrients removal, and fouling rate reduction.

Recent Trends in Pharmaceuticals Removal from Water Using Electrochemical Oxidation Processes

Nowadays, the research on the environmental applications of electrochemistry to remove recalcitrant and priority pollutants and, in particular, drugs from the aqueous phase has increased dramatically. This literature review summarizes the applications of electrochemical oxidation in recent years to decompose pharmaceuticals that are often detected in environmental samples such as carbamazapine, sulfamethoxazole, tetracycline, diclofenac, ibuprofen, ceftazidime, ciprofloxacin, etc. Similar to most physicochemical processes, efficiency depends on many operating parameters, while the combination with either biological or other physicochemical methods seems particularly attractive. In addition, various strategies such as using three-dimensional electrodes or the electrosynthesis of hydrogen peroxide have been proposed to overcome the disadvantages of electrochemical oxidation. Finally, some guidelines are proposed for future research into the applications of environmental electrochemistry for the degradation of xenobiotic compounds and micropollutants from environmental matrices. The main goal of the present review paper is to facilitate future researchers to design their experiments concerning the electrochemical oxidation processes for the degradation of micropollutants/emerging contaminants, especially, some specific drugs considering, also, the existing limitations of each process.

Secondary treatment phase of tertiary wastewater treatment works significantly reduces estrogenic load

Estrogenic compounds enter waterways via effluents from wastewater treatment works (WWTW), thereby indicating a potential risk to organisms inhabiting adjacent receiving waters. However, little is known about the loads or concentrations of estrogenic compounds that enter Australian WWTWs, the efficiency of removing estrogenic compounds throughout the various stages of tertiary WWTW processes (which are common in Australia), nor the concentrations released into estuarine or marine receiving waters, and the associated risk for aquatic taxa residing in these environments. Therefore, seven estrogenic compounds, comprising the natural estrogens estrone (E1), 17β-estradiol (E2) and estriol (E3), the synthetic estrogen (EE2), and the industrial chemicals bisphenol A (BPA), 4-t-octyl phenol (4-t-OP) and 4-nonyl phenol (4-NP), in wastewater samples were quantified via liquid chromatographic-mass spectrometry (LC-MS) after solid-phase extraction at different stages of wastewater treatment and associated receiving waters. The concentrations of the target compounds in wastewater ranged from < LOQ (limit of quantification) to 158 ng/L for Tanilba Bay WWTW and < LOQ to 162 ng/L for Belmont WWTW. Most target compounds significantly declined after the secondary treatment phase. Appreciable removal efficiency throughout the treatment process was observed with removal from 39.21 to 99.98% of influent values at both WWTWs. The reduction of the natural estrogens (E1, E2 and E3) and 4-t-OP were significantly greater than EE2, BPA, and 4-NP in both WWTWs. Risk quotients (RQs) were calculated to assess potential ecological risks from individual estrogenic compounds. In predicted diluted effluents, no targeted compounds showed any ecological risk (RQ ≤1.65 × 10^-2) at both WWTWs. Similarly, all RQs for shore samples at both WWTWs were below 1. Finally, the hazard index (HI), which represents combined estrogenic contaminants' ecological risk, indicated no mentionable risk for predicted diluted effluents (HI = 0.0097 to 0.0218) as well as shoreline samples (HI = 0.393 to 0.522) in the receiving estuarine or marine waters.

Innovative membrane photobioreactor for sustainable CO2 capture and utilization

The rising of greenhouse-gas emissions (GHG), during the last 200 years, is associated to the well known global warming phenomena. One of the main sources of CO₂-equivalent GHGs emissions are the environmental protection plants accounting for 1.57% of the global emissions and thus sustainable and effective technologies for their mitigation are strongly needed. The current paper presents and discusses the assessment of an innovative membrane photo-bioreactor (MPBR) whose aim was the promotion of CO₂ capture from conveyed flows, such as those from wastewater treatment plants (WWTPs), landfill and composting plants, for production and energy valorisation of algal biomass. Chlorella vulgaris microalgae strain was selected as photosynthetic platform for the abovementioned purposes. The influence of various operating parameters has been explored, including the photosynthetic photon flux densities (PPFD) (60 and 120 μmol m^-2 s^-1), liquid/gas ratio (L/G = 5, 10 or 15) and CO₂ concentration (5, 10 and 15%) in order to investigated their effects on carbon capture effectiveness and biomass production. The results demonstrated that the increasing of PPFD significantly enhanced the biomass production in terms of biomass productivity (P) and total dry weight (DW). The highest biomass concentration of 1.01 g L^-1 was achieved at PPFD of 120 μmol m^-2 s^-1 with a L/G of 15. Under the aforementioned conditions, carbon dioxide removal efficiency (RE) reached values up to 80%. In addition, the novel MPBR equipped with an innovative self-forming dynamic membrane (SFDM) showed a simultaneous biomass harvesting rate of 41 g m^-2 h^-1.

Emerging contaminants in the water bodies of the Middle East and North Africa (MENA): A critical review

Many emerging contaminants (ECs) are not currently removed by conventional water treatment methods and consequently, often reach the aquatic environment. In the absence of proper management strategies, ECs can accumulate in water bodies, which poses potential environmental and health risks. This paper critically reviews, for the first time, the reported occurrence and treatment of ECs in the Middle Eastern and North Africa (MENA) region. The paper also provides recommendations to properly manage EC risks. In the MENA region, pharmaceuticals and personal care products (PPCPs) have been detected in surface water, seawater, groundwater, and wastewater treatment plants. A focus on surface water in the published literature suggests that studies are skewed towards worldwide trends, whereas studies on ECs in seawater are of great importance in the study region. The types of PPCPs detected in the MENA region vary, but anti-inflammatories and antibiotics dominate. In comparison, microplastics have mainly been studied in surface waters and seawater with much less focus on drinking water. The majority of microplastics in the region are secondary types resulting from the degradation of larger plastic debris; polyethylene (PE) and polypropylene (PP) fibers are the most frequently detected polymers, which are indicative of local anthropogenic sources. Research progress on ECs varies between countries, having received more attention in Iran and Tunisia. Most MENA countries have now begun monitoring water bodies for ECs; however, studies are still lacking in some countries including Sudan, Djibouti, Syria, Ethiopia, and Bahrain. Based on this review, critical knowledge gaps and research needs are identified. Countries in the MENA region require further research on a broader range of EC types. Overall, water pollution due to the use and release of ECs can be tackled by improving public awareness, public campaigns, government intervention, and advanced monitoring and treatment methods.

Biodegradation performance and biofouling control of a halophilic biocarriers-MBR in saline pharmaceutical (ampicillin-containing) wastewater treatment

This work develops a halophilic biocarriers-MBR for saline pharmaceutical wastewater treatment. The system has effectively treated the ampicillin-containing saline wastewater for 32 days, when the ampicillin concentration is lower than 20 mg/L. The system can tolerate the saline organic wastewater with a reasonable biodegradability (removals of COD over 75%) when the ampicillin concentration is 50 mg/L. The system has a bad performance in biodegradation (COD removals around 60-70%) and fouled within 16 days at a high ampicillin concentration of 100 mg/L. At high transmembrane pressures over 30 KPa, some ampicillin molecules may permeate through the membrane causing decreases in the ampicillin removal. The concentrations of protein and carbohydrate in EPS and SMP have increased over time and with increasing the ampicillin concentration. The method of biofouling control in MBR for the ampicillin situations has been proposed based on monitoring the concentrations of EPS and SMP. The drying-assisted monitoring of membrane biofoulants has showed a better efficiency than the monitoring of transmembrane pressure for membrane anti-biofouling in the treatment of pharmaceutical saline wastewaters where a spectroscopic detection can be hardly applied. This work may benefit relative research works for the control of biodegradation performance and membrane biofouling to better treat saline pharmaceutical wastewaters.

Electrochemical membrane bioreactors: State-of-the-art and future prospects

Integration of an electrochemical process with membrane bioreactor (MBR) has attracted considerable attention in the last decade for simultaneous improvement in pollutant removal and hydraulic performance of MBR. Electrochemical MBR (eMBR) with sacrificial anodes has been observed to achieve enhanced phosphorus (up to 40%) and micropollutant removal (5-60%). This is because direct anodic oxidation, indirect oxidation by reactive oxygen species and electrocoagulation can supplement the biological process. The application of an electric field can substantially reduce membrane fouling by 10% to 95% in the eMBR as compared to the conventional MBR. Sacrificial electrodes (e.g., iron or aluminium) have been reported to be more suitable for fouling mitigation than non-sacrificial electrodes (e.g., titanium). However, during prolonged operation, metal ions released from sacrificial electrodes can adversely affect microbial activity and could accumulate in activated sludge. Depending on the current density and electrode material (sacrificial or non- sacrificial), anodic oxidation, electrocoagulation, electrophoresis and/or electroosmosis mechanisms are responsible for suppressing membrane fouling propensity. This paper critically reviews the current status of the electrochemical MBR technology and presents a concise summary of eMBR configurations and electrode materials. Comparative removal of bulk organics, nutrients and micropollutants in the eMBR and conventional MBR is discussed, and performance governing factors are elucidated. Impacts of operating conditions such as current density on mixed liquor properties (e.g., floc size and zeta potential) and microbial activity are elucidated. The extent of membrane fouling mitigation along with associated mechanisms as well as energy consumption is explained and critically analysed. Future research directions are suggested to fast track the scalability of eMBR, which include but are not limited to electrode lifetime, development of self-cleaning conductive membranes, optimisation of operating parameters, removal of emerging micropollutants, accumulation of toxic metals in activated sludge, and degradation by-products and ecotoxicity.

Emerging pollutants-Part II: Treatment

Emerging pollutants (EPs) refer to a class of pollutants, which are emerging in the environment or recently attracted attention. EPs mainly include pharmaceutical and personal care products (PPCPs), endocrine-disrupting chemicals (EDCs), and antibiotic resistance genes (ARGs). EPs have potential threats to human health and ecological environment. In recent years, the continuous detections of EPs in surface and ground water have brought huge challenges to water treatment and also made the treatment of EPs become an international research hotspot. This paper summarizes some research results on EPs treatment published in 2019. This paper may be helpful to understand the current situations and development trends of EP treatment technologies.

Recent Trends in Removal Pharmaceuticals and Personal Care Products by Electrochemical Oxidation and Combined Systems

Due to various potential toxicological threats to living organisms even at low concentrations, pharmaceuticals and personal care products in natural water are seen as an emerging environmental issue. The low efficiency of removal of pharmaceuticals and personal care products by conventional wastewater treatment plants calls for more efficient technology. Research on advanced oxidation processes has recently become a hot topic as it has been shown that these technologies can effectively oxidize most organic contaminants to inorganic carbon through mineralization. Among the advanced oxidation processes, the electrochemical advanced oxidation processes and, in general, electrochemical oxidation or anodic oxidation have shown good prospects at the lab-scale for the elimination of contamination caused by the presence of residual pharmaceuticals and personal care products in aqueous systems. This paper reviewed the effectiveness of electrochemical oxidation in removing pharmaceuticals and personal care products from liquid solutions, alone or in combination with other treatment processes, in the last 10 years. Reactor designs and configurations, electrode materials, operational factors (initial concentration, supporting electrolytes, current density, temperature, pH, stirring rate, electrode spacing, and fluid velocity) were also investigated.