How can we trace microplastics in wastewater treatment plants: A review of the current knowledge on their analysis approaches

Py-GC-MS analysis for microplastics: Unlocking matrix challenges and sample recovery when analyzing wastewater for polypropylene and polystyrene

Matrix interference and recovery when using pyrolysis gas chromatography (Py-GC-MS) to analyze wastewater for polystyrene (PS) and polypropylene (PP) microplastics (MP) was studied. Raw wastewater underwent a sample preparation train commonly applied for such matrix. The train consisted of six discrete steps to reduce the organic matter content without affecting MP in the sample. One large wastewater sample was collected, homogenized, and subdivided into 21 subsamples. Three samples were analyzed without further sample preparation. The remaining samples were divided in sets of three, and each set underwent an increasing number of steps of the procedure, up to the last set, which underwent the full treatment. The matrix effect on the determination of PS and PP was statistically evaluated by comparing in-matrix and external calibration curves at each step. Recovery of MP was assessed after each step by adding deuterated PS to the samples. A main finding was that there was no significant matrix effect for these polymers throughout the preparation train, suggesting that matrix components did not interfere with the analytical method. However, a significant loss of polymer mass was found between the steps, which may result in MPs falling below detection limits. Therefore, Py-GC-MS could be used for MP quantification before analysis by other techniques which require more extensive matrix removal. A downside of this approach is that analyzing such samples without matrix reduction will increase the need for instrumental maintenance.

Microplastic contamination in wastewater: Sources, distribution, detection and remediation through physical and chemical-biological methods

Microplastics are tiny plastic particles smaller than 5 mm. that have been widely detected in the environment, including in wastewater. They originate from various sources including breakdown of larger plastic debris, release of plastic fibres from textiles, and microbeads commonly used in personal care products. In wastewater, microplastics can pass through the treatment process and enter the environment, causing harm to biodiversity by potentially entering the food chain. Additionally, microplastics can act as a vector for harmful pollutants, increasing their transport and distribution in the environment. To address this issue, there is a growing need for effective wastewater treatment methods that can effectively remove microplastics. Currently, several physical and chemical methods are available, including filtration, sedimentation, and chemical degradation. However, these methods are costly, low efficiency and generate secondary pollutants. Furthermore, lack of standardization in the measurement and reporting of microplastics in wastewater, makes it difficult to accurately assess microplastic impact on the environment. In order to effectively manage these issues, further research and development of effective and efficient methods for removing microplastics from wastewater, as well as standardization in measurement and reporting, are necessary to effectively manage these detrimental contaminants.

Nano and microplastics occurrence in wastewater treatment plants: A comprehensive understanding of microplastics fragmentation and their removal

Nano/microplastic (NP/MP) pollution is a growing concern for the water environment. Wastewater treatment plants (WWTPs) are considered the major recipients of MP before discharging into local waterbodies. MPs enter WWTPs mainly from synthetic fibers through washing activities and personal care products. To control and prevent NP/MP pollution, it is essential to have a comprehensive understanding of their characteristics, fragmentation mechanisms, and the effectiveness of the current treatment processes used in WWTPs for NP/MP removal. Therefore, the objectives of this study are to (i) understand the detailed mapping of NP/MP in the WWTP, (ii) understand the fragmentation mechanisms of MP into NP, and (iii) investigate the removal efficiency of NP/MP by existing processes in the WWTP. This study found that fiber is the dominant shape of MP, and polyethylene, polypropylene, polyethylene terephthalate, and polystyrene are the major polymer type of MP in wastewater samples. Crack propagation and mechanical breakdown of MP due to water shear forces induced by treatment facilities (e.g., pumping, mixing, and bubbling) could be the major causes for NP generation in the WWTP. Conventional wastewater treatment processes are ineffective for the complete removal of MPs. Although these processes are capable of removing ∼95% of MPs, they tend to accumulate in sludge. Thus, a significant number of MPs may still be released into the environment from WWTPs on a daily basis. Therefore, this study suggested that using DAF process in the primary treatment unit can be an effective strategy to control MP in the initial stage before it goes to the secondary and tertiary stage.

Occurrence and sources of microplastics in dust of the Ebinur lake Basin, northwest China

Currently, there is a lack of studies on microplastic pollution in mountain terrains and foothills areas in Northwest China and Central Asia. Here, we collected monthly dusts samples for one year and we studied the distribution, pollution levels, and sources of microplastics in atmospheric dust fall in the Ebinur Lake Basin in Northwest China. Results showed that the average content of dust microplastic on construction land was 28.61 ± 1.13 mg/kg, followed by farmland (20.25 ± 1.56 mg/kg), forest (19.52 ± 1.06 mg/kg), and deserts (8.08 ± 0.56 mg/kg). Regarding different land use types, atmospheric dust reduction dominated on farmland (58.64%), followed by urban area (26.65%), forest (9.76%), and desert (4.95%). Regarding the shape of microplastics, the order of occurrence in dust was film (46.85%) > fiber (35.15%) > foam(12.35%) > fragment (5.65%). In this study, four colors of microplastics were found in dust, and white accounted for the largest proportion (52.15%), followed by transparent (18.65%), black (19.45%), and green (9.75%). The main components of film microplastics in atmospheric dustfall in the Ebinur Lake Basin were PE and PP, and their sources were mainly plastic products in daily life, plastic industrial packaging materials from urban enterprises, broken plastic woven bags, and PET mostly from fabric fragment emissions. The abundance of microplastics in dust was correlated with atmospheric dust pH, EC, and total salt content. The contents of seven heavy metals (Cu, Ni, Cd, Pb, Cr, Mn, and Co) adsorbed by microplastics were also correlated with pH, EC, and total salt content. Our results represent a reference for microplastics pollution prevention in mountain terrains and foothills areas in northwest China and Central Asia.

Microplastics identification and quantification in the composted Organic Fraction of Municipal Solid Waste

Composted Organic Fraction of Municipal Solid Waste (OFMSW) is used in agricultural soils as a source of organic matter and nutrients. Besides, its use avoids landfilling or incineration following the principles of circular economy. It is well established that source separated OFMSW is suitable for compost production, but its quality depends on their content in non-compostable materials. In this work, we selected and studied the final refined compost form five OFMSW facilities over a five-month period. The plants displayed differences in collection systems, concentration on non-desired materials, treatment technology and density of served population. The presence of plastic was studied using a separation and identification process that consisted of oxidation and flotation followed by spectroscopic identification. The results showed a concentration of plastic impurities in the 10-30 items/g of dry compost range. The concentration of small fragments and fibres (equivalent diameter < 5 mm) was in the 5-20 items/g of dry weight range and were dominated by fibres (25% of all particles <500 μm). Five polymers represented 94% of the plastic items: polyethylene, polystyrene, polyester, polypropylene, polyvinyl chloride, and acrylic polymers in order of abundance. Polyethylene was more abundant in films, polystyrene in fragments, polypropylene in filaments, and fibres were dominated by polyester. Our results showed that smaller plants, with OFMSW door-to-door collection systems produced compost with less plastic of all sizes. Compost from big facilities fed by OFMSW from street bin collection displayed the highest contents of plastics. No debris from compostable bioplastics were found in any of the samples, meaning that if correctly composted their current use does not contribute to the spreading of anthropogenic pollution. Our results suggested that the use of compostable polymers and the implementation of door-to-door collection systems could reduce the concentration of plastic impurities in compost from OFMSW.

Microplastic retention in small and medium municipal wastewater treatment plants and the role of the disinfection

Wastewater treatment plants (WWTPs) efficiently retain microplastic particles (MPs) generated within urban areas. Among the wastewater treatment steps, disinfection has not been characterized for its potential MPs retention activity, although it has been reported that processes used to abate the bacterial load could also affect MPs concentration. For this reason, we evaluated the MPs concentration across the overall wastewater treatment process and before and after the disinfection step in four small/medium WWTPs located in the north of Italy. Most of the MPs found in the samples were fibers or fragments, smaller than 500 μm, mainly composed of polyethylene, polypropylene, or polyethylene terephthalate. The retention efficiency at the outlets was higher than 94% in all the plants analyzed. More interestingly, the disinfection treatments adopted by the different WWTPs reduced MPs concentration from a minimum of 9.1% (UV treatment) to a maximum of 67.6% (chlorination), promoting a further increase of the overall retention efficiency of the WWTPs from 0.4 to 0.7%. Quantitatively, the disinfection contributes to the MPs reduction in the outlets by retaining 0.5-6.7 million MPs per day, in WWTPs that discharge 2.7-12 million MPs per day. The results of the present work underline the importance of a careful choice of the steps that constitute the wastewater treatment, including disinfection, in order to minimize MPs discharge into the natural ecosystems.

Facemask Global Challenges: The Case of Effective Synthesis, Utilization, and Environmental Sustainability

Coronavirus disease (COVID-19), caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), has caused a rapidly spreading pandemic and is severely threatening public health globally. The human-to-human transmission route of SARS-CoV-2 is now well established. The reported clinical observations and symptoms of this infection in humans appear in the range between being asymptomatic and severe pneumonia. The virus can be transmitted through aerosols and droplets that are released into the air by a carrier, especially when the person coughs, sneezes, or talks forcefully in a closed environment. As the disease progresses, the use and handling of contaminated personal protective equipment and facemasks have become major issues with significant environmental risks. Therefore, providing an effective method for treating used/contaminated facemasks is crucial. In this paper, we review the environmental challenges and risks associated with the surge in facemask production. We also discuss facemasks and their materials as sources of microplastics and how disposal procedures can potentially lead to the contamination of water resources. We herein review the potential of developing nanomaterial-based antiviral and self-cleaning facemasks. This review discusses these challenges and concludes that the use of sustainable and alternative facemask materials is a promising and viable solution. In this context, it has become essential to address the emerging challenges by developing a new class of facemasks that are effective against the virus, while being biodegradable and sustainable. This paper represents the potentials of natural and/or biodegradable polymers for manufacturing facemasks, such as wood-based polymers, chitosan, and other biodegradable synthetic polymers for achieving sustainability goals during and after pandemics.

Sewage sludge as a source of microplastics in the environment: A review of occurrence and fate during sludge treatment

Modern wastewater treatment plants (WWTPs) effectively remove microplastics (MPs) from wastewater and unsurprisingly concentrate them in sludge. Hence through its beneficial use and disposal, sludge causes secondary release pathways of an estimated average amount of 10⁶ to 10¹⁴ wastewater-based MPs to various environmental compartments yearly. Despite these numbers, studies investigating sludge are scarce. Currently, majority of the studies in the field focus on identifying the magnitude of the problem, whereas research investigating the fate and effects of MPs during sludge treatment are very rare. This review aims to bring together and critically evaluate the limited studies conducted about MPs in the sludge treatment line and bring out the key gaps and research needs in the area. Studies conducted so far indicate that depending on the type, size, and amount of MPs, their effects during anaerobic digestion differ, with some studies demonstrating serious negative impact on biogas production. Possible effect mechanisms are also suggested such as formation of reactive oxygen species (ROS) and leaching of toxic chemicals. Moreover, a potential for sludge treatment processes (thickening, dewatering, drying, stabilization, etc.) to change the characteristics and the number of MPs, which may increase surface area available for adsorption and desorption of pollutants, was observed. Review uncovers that, in the broad universe of MPs, some highly abundant ones in sludge such as polypropylene, polyurethane, polycarbonate, and acrylic are not yet investigated in sludge treatment. Future research should focus not only to investigate the fate/effects but to fully understand the mechanisms behind these, which is missing in many studies reviewed. Besides, new studies show that effect of MPs start from the floc formation stage during biological treatment, which in fact determine the final sludge behavior in thickening and dewatering. Therefore, holistic approaches starting from wastewater till sludge exits WWTP seem necessary. Substantiating from polymer chemistry and response of plastics to stress conditions, review suggests possibilities of deterioration during sludge treatment processes. It becomes evident that some totally uninvestigated aspects such as disintegration conducted before stabilization, can change the fate of MPs during sludge treatment and may bring new perspectives to the solution of the problem.

Water science under the global epidemic of COVID-19: Bibliometric tracking on COVID-19 publication and further research needs

There are overwhelming increases of studies and over 200,000 publications related to all the aspects of COVID-19. Among them, 262 papers were published by authors from 67 countries regarding COVID-19 with water science and technology. Although the transmission routes of SARS-CoV-2 in water cycle have not been proved, the water and wastewater play an important role in the control of COVID-19 pandemic. Accordingly, it is scholarly relevant and interesting to look into publications of COVID-19 in water science and technology to track the investigations for moving forward in the years to come. It is believed that, through the literature survey, the question on what we know and what we do not know about COVID-19 so far can be clear, thus providing useful information for helping curbing the epidemic from water sector. This forms the basis of the current study. As such, a bibliometric analysis was conducted. It reveals that wastewater-based epidemiology (WBE) has recently gained global attention with the source and survival characteristics of coronavirus in the aquatic environment; the methodology of virus detection; the water hygiene; and the impact of the COVID-19 pandemic on the water ecosystem being the main topics in 2020. Various studies have shown that drinking water is safety whereas wastewater may be a potential risk during this pandemic. From the perspective of the water cycle, the scopes for further research needs are discussed and proposed, which could enhance the important role and value of water science in warning, monitoring, and predicting COVID-19 during epidemic outbreaks.

Optimising sample preparation for FTIR-based microplastic analysis in wastewater and sludge samples: multiple digestions

The lack of standardised methodologies in microplastic research has been addressed in recent years as it hampers the comparison of results across studies. The quantification of microplastics in the environment is key to the assessment of the potential eco-toxicological impacts that this new category of emerging pollutants could have on terrestrial and aquatic species. Therefore, the need for protocols that are robust, simple and reliable together with their standardisation are of crucial importance. This study has focused on removal of organic matter with Fenton reagent from wastewater and sludge samples. This step of analysis was optimised by implementing a multi-digestion treatment on these samples that have high concentration of complex mixtures of organic matter, which interfere with microplastic enumeration. Moreover, this study targeted the detection of microplastics in the sub-hundred-micron size range due to the potential higher risks associated with smaller-sized particles and the limited data available from previous wastewater research. To show the validity of the method, triplicate samples of raw sewage, final effluent and sludge were independently spiked with two different sizes and types of microplastic polymers. Due to the various analytical stages required for the isolation of microplastics, time is a limiting factor in sample processing. The sequential digestion with Fenton reagent represents an inexpensive and time-efficient procedure for wastewater research providing effective degradation of organic material. These advantages over other currently available methods mean the method is suitable for analysis of large numbers of samples allowing robust monitoring data sets to be generated.