Caffeine removal from aqueous media by adsorption: An overview of adsorbents evolution and the kinetic, equilibrium and thermodynamic studies

Enrichment and detection of polycyclic aromatic hydrocarbon in tea and coffee using phenyl-functionalized NiFe2O4@Ti3C2TX based magnetic solid-phase extraction

Polycyclic aromatic hydrocarbons (PAHs) are commonly found in various environmental matrices and have received significant attention due to their toxic effects on ecosystems and environmental health. In this study, a specific magnetic composite material derived from MXene, known as phenyl-functionalized NiFe2O4@Ti3C2TX, was designed and synthesized using a simple method. This composite material was used to develop an effective magnetic solid-phase extraction (MSPE) method for enriching trace polycyclic aromatic hydrocarbons (PAHs) in tea and coffee samples. The eluted PAHs were analyzed via gas chromatography-tandem mass spectrometry. Under optimal conditions, this method exhibited excellent linear relationships for 16 PAHs within the ranges of 0.001-25 and 0.0005-25 μg/L, with correlation coefficients exceeding 0.9979. The limits of detection for the target PAHs ranged from 0.1 to 0.3 ng/L. The effectiveness of the proposed method was evaluated by analyzing tea and coffee samples, and the satisfactory spiked recoveries of PAHs ranged from 84.5% to 112.6%.

Valorization and Upcycling of Acid Mine Drainage and Plastic Waste via the Preparation of Magnetic Sorbents for Adsorption of Emerging Contaminants

Plastic waste poses a serious environmental risk, but it can be recycled to produce a variety of nanomaterials for water treatment. In this study, poly(ethylene terephthalate) (PET) waste and acid mine drainage were used in the preparation of magnetic mesoporous carbon (MMC) nanocomposites for the adsorptive removal of pharmaceuticals and personal care products (PPCPs) from water samples. The latter were then characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and ζ potential. The results of Brunauer-Emmett-Teller isotherms revealed high specific surface areas of 404, 664, and 936 m2/g with corresponding pore sizes 2.51, 2.28, and 2.26 nm for MMC, MMAC-25%, and MMAC-50% adsorbents, respectively. Under optimized conditions, the equilibrium studies were best described by the Langmuir and Freundlich models and kinetics by the pseudo-second-order model. The maximum adsorption capacity for monolayer adsorption from the Langmuir model was 112, 102, and 106 mg/g for acetaminophen, caffeine, and carbamazepine, respectively. The composites could be reused for up to six cycles without losing their adsorption efficiency. Furthermore, prepared adsorbents were used to remove acetaminophen, caffeine, and carbamazepine from wastewater samples, and up to a 95% removal efficiency was attained.

Management of caffeine in wastewater using MOF and perovskite materials: optimization, kinetics, and adsorption isotherm modelling

Pharmaceuticals and personal care products (PPCPs) have been increasingly used all over the world and they have been reported on water cycle and cause contamination. Among these pharmaceuticals is caffeine (CAF). In this work, CAF removal from aqueous samples by metal-organic framework (UIO-66) and perovskite (La0.7Sr0.3FeO3) was achieved. Detailed studies on the preparation of MOFs and perovskite oxides compounds have been presented. Extensive characterizations such as X-Ray diffraction (XRD), field emission scanning electron microscope (FESEM), Fourier transform infrared spectra (FT-IR), N2 adsorption-desorption isotherms were also carried out to assure proper formation and to better understand the physico-chemical behavior of the synthesized samples before and after adsorption. Batch experiments of CAF adsorption onto both MOFs and perovskite were performed to compare the effectiveness of both materials on the removal competence of the CAF residue at different conditions including the effect of pH, initial concentration, and contact time. It was observed that the adsorption capacity of CAF by MOF increased with increasing acidity. On the other hand, the adsorption capacity of perovskite is stable in pH 4-10. The maximum adsorption capacities of UiO-66 and perovskite toward CAF are high as 62.5 mg g-1 and 35.25 mg g-1, respectively. Equilibrium isotherms were investigated by numerous models: Langmuir, Freundlich, Temkin, Redlich-Peterson, Sips, Langmuir-Freundlich, Toth, Kahn, Baudu, and Fritz Schlunder. Moreover, the kinetics of the CAF@MOF and CAF@Perovskite systems have been studied by five kinetic models (Pseudo-1st -order (PFO), Pseudo-2nd -order (PSO), Mixed 1st, 2nd-order, Intraparticle diffusion and Avrami). The best model described the adsorption of CAF onto both of MOF and perovskite was the mixed 1st, 2nd-order model. The metal-organic framework and perovskite were applied to quickly extract CAF from water samples successfully. The maximum removal percentage obtained for MOF and perovskite was 0.89% and 0.94% respectively within 30 min contact time which suggests that these materials are considered as promising adsorbents for CAF.

Sustainable removal of caffeine and acetaminophen from water using biomass waste-derived activated carbon: Synthesis, characterization, and modelling

The removal of caffeine (CFN) and acetaminophen (ACT) from water using low-cost activated carbons prepared from artichoke leaves (AAC) and pomegranate peels (PAC) was reported in this paper. These activated carbons were characterized using various analytical techniques. The results showed that AAC and PAC had surface areas of 1203 and 1095 m2 g-1, respectively. The prepared adsorbents were tested for the adsorption of these pharmaceuticals in single and binary solutions. These experiments were performed under different operating conditions to evaluate the adsorption properties of these adsorbents to remove CFN and ACT. AAC and PAC showed maximum adsorption capacities of 290.86 and 258.98 mg g-1 for CFN removal, 281.18 and 154.99 mg g-1 for the ACT removal over a wide pH range. The experimental equilibrium adsorption data fitted to the Langmuir model and the kinetic data were correlated with the pseudo-second order model. AAC showed the best adsorption capacities for the removal of these pharmaceuticals in single systems and, consequently, it was tested for the simultaneous removal of these pollutants in binary solutions. The simultaneous adsorption of these compounds on AAC was improved using the central composite design and response surface methodology. The results indicated an antagonistic effect of CFN on the ACT adsorption. AAC regeneration was also analyzed and discussed. A statistical physics model was applied to describe the adsorption orientation of the tested pollutants on both activated carbon samples. It was concluded that AAC is a promising adsorbent for the removal of emerging pollutants due to its low cost and reusability properties.

Novel manganese and nitrogen co-doped biochar based on sodium bicarbonate activation for efficient removal of bisphenol A: Mechanism insight and role analysis of manganese and nitrogen by combination of characterizations, experiments and density functional theory calculations

A novel porous manganese and nitrogen co-doped biochar (Mn-N@SBC) was synthesized via one-step pyrolysis, utilizing loofah agricultural waste as the precursor and NaHCO3 as the activator. The behavior of bisphenol A adsorbed on Mn-N@SBC was evaluated using static batch adsorption experiments. Compared to direct manganese-nitrogen co-doping, co-doping based on NaHCO3 activation significantly increased the specific surface area (231 to 1027 m2·g-1) and adsorption capacity (15 to 351 mg·g-1). Wide pH (2-10) and good resistance to cation/anion, humic acid and actual water demonstrated the robust adaptability of Mn-N@SBC to environmental factors. The significantly reduced specific surface area after adsorption, adverse effects of ethanol and phenanthrene on the removal of bisphenol A, and theoretically predicted interaction sites indicated the primary adsorption mechanisms involved pore filling, hydrophobicity, and π-π-electron-donor-acceptor interaction. This work presented an approach to create high-efficiency adsorbents from agricultural waste, offering theoretical and practical guidance for the removal of pollutants.

Insights into the pH-dependent interactions of sulfadiazine antibiotic with soil particle models

Sulfonamide antibiotics (SAs) are widely used as a broad-spectrum antibiotic, leading to global concerns due to their potential soil accumulation and subsequent effects on ecosystems. SAs often exhibit remarkable environmental persistence, necessitating further investigation to uncover the ultimate destiny of these molecules. In this work, molecular dynamics simulations combined with complementary quantum chemistry calculations were employed to investigate the influence of pH on the behavior of sulfadiazine (SDZ, a typical SAs) in soil particle models (silica, one of the main components of soil). Meanwhile, the quantification of SDZ molecules aggregation potential onto silica was further extended. SDZ molecules tend to form a monolayer on the soil surface under acidic conditions while forming aggregated adsorption on the surface under neutral conditions. Due to the hydrophilicity of the silica, multiple hydration layers would form on its surface, hindering the further adsorption of SDZ molecules on its surface. The calculated soil-water partition coefficient (Psoil/water) of SDZ+ and SDZ were 9.01 and 7.02, respectively. The adsorption evaluation and mechanisms are useful in controlling the migration and transformation of SAs in the soil environment. These findings provide valuable insights into the interactions between SDZ and soil components, shedding light on its fate and transport in the environment.

Evaluation of hydrochar from peach stones for caffeine removal from aqueous medium and treatment of a synthetic mixture

The presence of micropollutants, such as caffeine (CAF), has been detected throughout the world, since conventional treatment plants are not able to properly degrade them. CAF is a widely consumed stimulant, and has been demanding the development of efficient methodologies for its removal. Aiming at the agriculture waste valorization, a new hydrochar was developed based on chemical and thermal modification of peach stones (mod-PS) for CAF removal from water and from a synthetic mixture. The morphology, functional groups and surface electrical charge of the adsorbent were characterized by SEM, FTIR and zeta potential, respectively. Regarding CAF adsorption performance, the equilibrium time was reached at 480 min and the pseudo-second-order model presented the best fit for the experimental data. The maximum adsorption capacity was 68.39 mg g-1 (298 K) and the Langmuir model exhibited a better fit for the isothermal data. The thermodynamic properties confirmed that the process was exothermic, spontaneous and reversible. The main adsorption mechanisms were hydrogen bonds and π-interactions. The global removal efficiency was satisfactory in the synthetic mixture simulating real wastewater (67%). Therefore, the proposed new hydrochar has potential application as a low-cost adsorbent for CAF removal.

Adsorption on activated carbon combined with ozonation for the removal of contaminants of emerging concern in drinking water

The presence of Contaminants of Emerging Concern (CECs) in drinking water is raising concern for potential negative effects on human health. Ozonation and adsorption on activated carbon are the most suitable processes for CECs removal in drinking water treatment plants (DWTPs). This study aims at evaluating the performance of ozonation and adsorption as in-series processes compared to those of the stand-alone processes, focusing on 18 compounds representative of various CECs families. No CECs spike was performed to evaluate the effectiveness of these processes towards CECs at their environmental concentrations. Adsorption isotherms were performed on water samples collected before and after the full-scale ozonation in a DWTP, testing different combinations of ozone and activated carbon doses. Generally, the combination of the two processes was beneficial (83% average removal) compared to adsorption and ozonation alone (71% and 34% average removal respectively). The effect of ozonation on adsorption depends on CECs reactivity with ozone, since ozonation improves the adsorption performance of poorly-oxidizable CECs, but worsens that of well-oxidizable compounds. The removal of organic matter, investigated by absorbance at 254 nm and fluorescence, by ozonation reduces competition for the subsequent CECs removal by adsorption (up to 20% increase of total CECs adsorption). Finally, the removal of both absorbance and fluorescence seems to be a good proxy variables for total CECs adsorption, with different relationships depending on the presence of ozonation. Conversely, it is not effective for ozonation, since the relationship depends on the reactivity of the specific CEC with ozone.

Removal of two antidepressant active pharmaceutical ingredients from hospital wastewater by polystyrene-coated magnetite nanoparticles-assisted batch adsorption process

This study employed simple polystyrene-coated magnetite nanoparticles (PS@MNPs)-assisted batch adsorption process for the removal of two antidepressant active ingredients (amitriptyline HCl and sertraline HCl) from hospital wastewater. Dominant parameters of the adsorption process including pH, adsorbent amount, and contact period were optimized through the univariate approach to enhance the adsorption efficiency. Upon reaching optimum adsorption conditions, equilibrium experiments were performed by spiking the adsorbates in hospital wastewater in the concentration range of 100-2000 μg/L. The concentrations of the adsorbates in the effluent were calculated using the matrix-matching calibration strategy to enhance the accuracy of quantification. A validated switchable solvent-based liquid phase microextraction (SS-LPME) method was employed to enrich the two active pharmaceutical ingredients (APIs) prior to sensitive determination with GC-MS (gas chromatography-mass spectrometry). The equilibrium data were mathematically modeled employing the Langmuir and Freundlich adsorption isotherm models. The isotherm constants were calculated, and the results showed that both the isotherm models fitted well with the experimental data. The efficient and simple batch adsorption strategy reported in this study was successfully employed to remove amitriptyline HCl and sertraline HCl from hospital wastewater at low concentrations.

Competitive adsorption of acetaminophen and caffeine onto activated Tingui biochar: characterization, modeling, and mechanisms

Tingui biochar (TB) activated with potassium hydroxide (TB-KOH) was synthesized in the present study. The adsorption capacity of TB-KOH was evaluated for the removal of acetaminophen and caffeine in monocomponent and bicomponent solutions. As a result, the study of the TB-KOH characterization as well as the adsorption kinetics, isotherm, thermodynamics, and a suggestion of the global adsorption mechanism are presented. TB-KOH was characterized through physical-chemical analysis to understand its surface morphology and how it contributes to the adsorption of these drugs. Furthermore, modelling using advanced statistical physical models was performed to describe how acetaminophen and caffeine molecules are adsorbed in the active sites of TB-KOH. Through the characterizations, it was observed that the activation with KOH contributed to the development of porosity and functional groups (-OH, C-O, and C = O) on the surface of TB. The monocomponent adsorption equilibrium was reached in 90 min with a maximum adsorption capacity of 424.7 and 350.8 mg g-1 for acetaminophen and caffeine, respectively. For the bicomponent solution adsorption, the maximum adsorption capacity was 199.4 and 297.5 mg g-1 for acetaminophen and caffeine, respectively. The isotherm data was best fitted to the Sips model, and the thermodynamic study indicated that acetaminophen removal was endothermic, while caffeine removal was exothermic. The mechanism of adsorption of acetaminophen and caffeine by TB-KOH was described by the involvement of hydrogen bonds and π-π interactions between the surface of TB-KOH and the molecules of the contaminants.

Theoretical verification on adsorptive removal of caffeine by carbon and nitrogen-based surfaces: Role of charge transfer, π electron occupancy, and temperature

Eliminating an emerging water pollutant, caffeine molecules, from an aqueous solution using carbon and nitrogen-based adsorbents is of significant interest to public health. These adsorbents have been shown to have decent adsorption capacity toward caffeine due to their surface functionality. Therefore, screening various carbon and nitrogen-based surfaces can be a better option for high-performance adsorbents to remove caffeine efficiently from wastewater. Herein, we present combined first principles and molecular dynamics quantification of the adsorption enthalpies of caffeine molecules on the possible active sites of carbon and nitrogen-based adsorbents (graphene, phagraphene, graphdiyne, single-wall carbon nanotube, fullerene, and graphitic carbon nitride) with the incorporation of Van der Waals interactions. From the DFT calculations, N-doped carbon surfaces show the highest adsorption energies of single and dimer CAF compared to pristine carbon-based adsorbents. A charge density difference and Bader charge analysis display that high charge transfer occurs between the caffeine's oxygen and the surface's nitrogen atoms. An abundance of π-electrons from the nitrogen atoms, composed of large electron clouds of aromatic rings on the graphitic carbon surface, tends to favor extensive π-π interactions with the caffeine molecule. The high value of pz electron occupancy (1.445) of N in the hexagonal ring of the graphitic surface transfers additional charge transfer, which leads to strong adsorption energy of CAF than pristine surfaces. Also, the g-C3N4 surface adsorbs the CAF molecule with higher adsorption than other N-doped carbon surfaces due to the high pz_eo (1.5448) of N atoms on the surface. At 310 K, the water molecules' kinetics aids the single and dimer caffeine molecules to adsorb with the highest adsorption energies on the active sites of g-C3N4 surfaces than graphene adsorbent.

Removal of hydrophilic, hydrophobic, and charged xenobiotic organic compounds from greywater using green wall media

Green walls offer a novel on-site approach for greywater treatment and reuse in densely build urban environments. However, they need to be engineered for effective removal of a wide range of emerging contaminants such as xenobiotic organic compounds (XOCs), which may be present in greywater due to extensive use of personal care products and household chemicals. This study used laboratory column design and batch experiments to investigate the performance of three lightweight green wall media (coco coir, zeolite, and perlite) and their mixture in three different combinations for the removal of twelve XOCs, covering wide range of hydrophilic, hydrophobic, and charged pollutants in greywater. The experiments were designed to assess the removal of targeted XOCs under different operational condition (i.e., hydraulic loading, infiltration rate, drying) and uncover the dominant mechanisms of their removal. Results showed excellent removal (>90%) of all XOCs in coco coir and media mix columns at the start of the experiment (i.e., fresh media and initial 2 pore volume (PV) of greywater dosing). The removal of highly hydrophobic and positively charged XOCs remained high (>90%) under all operational conditions, while hydrophilic and negatively charged XOCs exhibited significant reduction in removal after 25 PV and 50 PV, possibly due to their low adsorption affinity and electrostatic repulsion from negatively charged media. The effect of infiltration rate on the removal of XOCs was not significant; however, higher removal was achieved after 2-weeks of drying in coco coir and media mix columns. The dominant removal mechanism for most XOCs was found to be adsorption, however, a few hydrophilic XOCs (i.e., acetaminophen and atrazine) exhibited both adsorption and biodegradation removal processes. While findings showed promising prospects of unvegetated media for removing XOCs from greywater, long term studies on vegetated green wall systems are needed to understand any synergetic contribution of plants and media in removing these XOCs.

Caffeine Synthesis and Its Mechanism and Application by Microbial Degradation, A Review

Caffeine is a metabolite derived from purine nucleotides, typically accounting for 2-5% of the dry weight of tea and 1-2% of the dry weight of coffee. In the tea and coffee plants, the main synthesis pathway of caffeine is a four-step sequence consisting of three methylation reactions and one nucleosidase reaction using xanthine as a precursor. In bacteria, caffeine degradation occurs mainly through the pathways of N-demethylation and C-8 oxidation. However, a study fully and systematically summarizing the metabolism and application of caffeine in microorganisms has not been established elsewhere. In the present study, we provide a review of the biosynthesis, microbial degradation, gene expression, and application of caffeine microbial degradation. The present review aims to further elaborate the mechanism of caffeine metabolism by microorganisms and explore the development prospects in this field.

Handleable TiO2-coated zeolitic material for photodecomposition of caffeine boosted by urine matrix

The photocatalytic decomposition of caffeine under UV-light irradiation was observed for the first time in a matrix of synthetic urine using granules of hydrogenated and iron-exchanged natural zeolite, coated with two loadings of TiO₂. A natural clinoptilolite-mordenite blend was used to prepare photocatalytic adsorbents coated with TiO₂ nanoparticles. The performance of the obtained materials was tested in the photodegradation of caffeine, a water contaminant of emerging concern. The photocatalytic activity was better in the urine matrix, due to the formation of surface complexes on the TiO₂ coating, cation exchange performed by the zeolite support, and use of the carrier electrons in the reduction of ions, affecting recombination of the electrons and holes during photocatalysis. The composite granules maintained photocatalytic activity for at least four cycles, with more than 50% of caffeine removal in the synthetic urine matrix.

A hypothetical model of multi-layered cost-effective wastewater treatment plant integrating microbial fuel cell and nanofiltration technology: A comprehensive review on wastewater treatment and sustainable remediation

Wastewater management has emerged as an uprising concern that demands immediate attention from environmentalists worldwide. Indiscriminate and irrational release of industrial and poultry wastes, sewage, pharmaceuticals, mining, pesticides, fertilizers, dyes and radioactive wastes, contribute immensely to water pollution. This has led to the aggravation of critical health concerns as evident from the uprising trends of antimicrobial resistance, and the presence of xenobiotics and pollutant traces in humans and animals due to the process of biomagnification. Therefore, the development of reliable, affordable and sustainable technologies for the supply of fresh water is the need of the hour. Conventional wastewater treatment often involves physical, chemical, and biological processes to remove solids from the effluent, including colloids, organic matter, nutrients, and soluble pollutants (metals, organics). Synthetic biology has been explored in recent years, incorporating both biological and engineering concepts to refine existing wastewater treatment technologies. In addition to outlining the benefits and drawbacks of the current technologies, this review addresses novel wastewater treatment techniques, especially those using dedicated rational design and engineering of organisms and their constituent parts. Furthermore, the review hypothesizes designing a multi-bedded wastewater treatment plant that is highly cost-efficient, sustainable and requires easy installation and handling. The novel setup envisages removing all the major wastewater pollutants, providing water fit for household, irrigation and storage purposes.

Integration of ozonation with water treatment for pharmaceuticals removal from Arroio Diluvio in southern Brazil

Pharmaceutical compounds can reach water bodies through sewage systems. The process of water treatment is insufficient for the removal of these contaminants. The ozonation has great potential to be integrated into the treatment, since it promotes the reduction of pharmaceuticals, reduces the generation of disinfection byproducts and can reduce operational costs. In this work, the integration of the ozonation process with water treatment was studied. The ozone was applied in the pre-oxidation and intermediate ozonation stages, to evaluate the dependence of different variables. Water samples were collected from Arroio Diluvio, a river of the city of Porto Alegre (Brazil). The doses of ozone were maintained between 0.5 and 1.0 mgO₃ L^-1 while the coagulant was between 25 and 150 mg·L^-1. Pre-ozonation resulted in a removal of pharmaceuticals at pH 10.0, time of 15 min and coagulant concentration of 52.5 mgL^-1. The intermediate ozonation provided a removal with pH 10.0 and a time of 5 min of bubbling. Based on the results, it was confirmed that the synergy of the ozonation process with conventional water treatment is an effective, sensitive and fast method for the removal of pharmaceuticals from the aqueous medium.

Synthesis and characterization of hydrogel-based magnetite nanocomposite adsorbents for the potential removal of Acid Orange 10 dye and Cr(VI) ions from aqueous solution

Magnetic responsive hydrogels (CMX-cl-P4VP/M-NPs) were successfully synthesized through in situ co-precipitation procedure and investigated using various techniques. The surface morphology analysis revealed that the M-NPs were uniformly distributed within the hydrogel matrix and had average sizes ranging from 4.98 to 15.02 nm. The graft copolymer containing nanoparticles exhibited a sensitive magnetic response, and their recovery could be facilitated by applying a magnetic field. The purpose of this research is to study the ability of the prepared magnetic hydrogel to remove AO-10 dye and hexavalent chromium ions (Cr(VI)) from the aqueous solution under various factors, namely contact time, pH, amount of adsorbent, coexisting ions and AO-10 and Cr(VI) concentrations. The outcomes of the batch adsorption demonstrated that the adsorbent hydrogel incorporated with a low percentage (10 %) of M-NPs had a strong affinity for the removal of AO-10 dye and Cr(VI) ions at an optimum pH = 3, and the removal percentage reached 99.3 and 97.4 % for 500 mg L^-1 and 300 mg L^-1 of AO-10 dye and Cr(VI) ions within 90, 50 min, respectively. The data were well-fitted by pseudo-first-order kinetics. The maximum adsorption capacities of AO-10 dye and Cr(VI) ions onto adsorbent were 2448 and 574.7 mg g^-1 at 298 K, calculated from the Langmuir model.

Highly effective sustainable membrane based cyanobacteria for uranium uptake from aqueous environment

Wastewater from industrial process of uranium ore mining contains a large amount of this radioactive pollutant. Regarding the advantages of biosorption, it was found that varieties of biomasses such as agricultural waste, algae and fungi are effective for uranium removal. However, there is limited research on cyanobacteria, therefore, cyanobacteria, Anagnostidinema amphibium (CAA) was investigated by batch method for the first time for biosorption of uranium (VI). Optimization of biosorption parameters showed that maximum removal efficiency of 92.91% was reached at pH range of 9-11 with 50 mg of cyanobacteria to 100 mg/L U(VI) initial concentration, at 25 °C within 40 min. Used biosorbent exhibited very good selectivity for U(VI) ions and reusability in IV sorption/desorption cycles. Characterization of CAA surface was performed by FTIR, EDS, EDXRF and SEM analysis and it has shown various functional groups (CONH, COOH, OH, PO alkyl group) and that it is very rich in elements such as iron, potassium and calcium. In binary systems, contained of U(VI) and selected ions, CAA exhibits very good selectivity towards U(VI) ions. Kinetic data revealed the best accordance of experimental data with the pseudo-second-order model and isotherms data agreed with Freundlich model. Thermodynamic data implied that U(VI) biosorption process by A. amphibium exhibited spontaneity and modelling of the investigated process showed that the adsorption of uranium ions occurs mainly via peptidoglycan carboxyl groups. Overall results show that these cyanobacteria with a maximum sorption capacity of 324.94 mg/g have great potential for the processing of wastewater polluted with uranium (VI).

Adsorptive removal of multiple organic dyes from wastewater using regenerative microporous carbon: Decisive role of surface-active sites, charge and size of dye molecules

Present work addresses the synthesis of microporous activated carbon (SDAC) by a facile thermochemical conversion of teak sawdust powder. The high surface area (1999 m² g^-1), excellent microporosity (average pore size: 2.62 nm), and turbostratic carbon structure with intertwined graphitic domains make SDAC a highly efficient adsorptive material for the removal of organic pollutants. The spectroscopic analyses (FTIR, Raman, and XPS) and adsorption locator calculations revealed multiple interactions between organic dyes and SDAC adsorbent, i.e., electrostatic, π-π, n-π interactions, and hydrogen linkages. The size, chemical functionalities, aromatic rings, electronegative and heteroatoms in dye molecules, along with the surface-active sites, microstructured and textural features of SDAC adsorbent collectively governed the interaction pathways and adsorption efficiency. The calculated adsorption energy using Monte Carlo-based simulation annealing method signified faster and higher adsorption of malachite green than methylene blue dye at surface-active sites (-COOH, CO, C-OH, and π-electron-rich domains) of SDAC adsorbent, corroborating the experimental results. The batch-mode adsorptive separation results showed remarkably high adsorption efficiency (>99%) for industrial wastewater to remove cationic and anionic dyes together. The SDAC displayed significantly high adsorption of methylene blue dye (625 mg.g^-1) with excellent recyclability without measurable loss of adsorption efficiency even after ten cycles. The SDAC fixed-bed column showed a dye removal capacity of 594 mg.g^-1 at 90% breakthrough in a continuous-mode process signifying its applicability for a real-time industrial run. The excellent conformity between batch mode and fixed bed continuous column adsorption data, along with higher removal capacity and remarkable recyclability, promise the use of SDAC adsorbent for industrial wastewater treatment to remove multiple organic pollutants.

Influence of Organic Matter on the Sorption of Cefdinir, Memantine and Praziquantel on Different Soil and Sediment Samples

Pharmaceuticals are known for their great effects and applications in the treatment and suppression of various diseases in human and veterinary medicine. The development and modernization of science and technologies have led to a constant increase in the production and consumption of various classes of pharmaceuticals, so they pose a threat to the environment, which can be subjected to the sorption process on the solid phase. The efficiency of sorption is determined by various parameters, of which the physicochemical properties of the compound and the sorbent are very important. One of these parameters that determine pharmaceutical mobility in soil or sediment is the soil−water partition coefficient normalized to organic carbon (Koc), whose determination was the purpose of this study. The influence of organic matter, suspended in an aqueous solution of pharmaceutical (more precisely: cefdinir, memantine, and praziquantel), was studied for five different types of soil and sediment samples from Croatia. The linear, Freundlich, and Dubinin−Raduskevich sorption isotherms were used to determine specific constants such as the partition coefficient Kd, which directly describes the strength of sorbate and sorbent binding. The linear model proved to be the best with the highest correlation coefficients, R2 > 0.99. For all three pharmaceuticals, a positive correlation between sorption affinity described by Kd and Koc and the amount of organic matter was demonstrated.

Fabrication of novel Fe/Mn/N co-doped biochar and its enhanced adsorption for bisphenol a based on π-π electron donor-acceptor interaction

In this work, a novel Fe/Mn/N co-doped biochar (Fe&Mn-NBC800) derived from waste apple tree branches was fabricated for bisphenol A (BPA) removal. Fe&Mn-NBC800 exhibited higher adsorption capacity (84.96 mg·g-1) in 318 K for BPA than the pristine biochar, doped mono-atomic, and di-atomic biochar. Higher temperature and adsorbent dosage promoted BPA removal, while higher solution pH was detrimental to the adsorption process. The kinetic and isothermal processes of BPA removal followed the pseudo-second-order model and Langmuir, respectively. Characterizations and correlation analysis indicated that π-π interactions showed the major contribution to the BPA adsorption. Furthermore, the pore filling, electrostatic interactions, hydrogen bonding, and hydrophobic interactions also played a role. Good water environment anti-interference ability (ion species, ionic strength, actual water body) and excellent recyclability of Fe&Mn-NBC800 make it exhibit the potential for engineering projects.

Mechanism and behavior of caffeine sorption: affecting factors

Caffeine is one of the emerging pollutants with a diverse chemical composition. It is mixed with the hydrobiota as a result of its high consumption, and when certain dose intervals are exceeded, it re-enters the human body through indirect routes such as plants, animals, soil, water, and the food chain, causing health problems that are difficult or impossible to treat, and irreversible environmental problems. This situation raises concerns about the presence of pollutants emerging in water resources, igniting interest in water treatment processes and the development of alternative methods. Although there are several methods for removing caffeine from aqueous media, adsorption is the most popular because it is less expensive than other methods and has the highest removal efficiency. Furthermore, it has the benefit of selectively attaching the molecules in solution. In this article, studies on the caffeine adsorption process have been examined, and the caffeine adsorption efficiency of various adsorbents has been summarized by compiling information such as pH, contact time, temperature, and concentration of adsorbent and adsorbate, which are considered as optimum processing conditions. The binding mechanism was investigated, and it was clearly stated how caffeine adheres to the adsorbent surface. Among the equilibrium adsorption isotherms, the isotherm model with the best agreement with the experimental data was attempted to be determined. Many studies clearly show that the process of developing environmentally friendly and high-capacity adsorbents in sustainable processes and in harmony with the circular economy is increasing day by day.

Sorption of cefdinir, memantine, praziquantel and trimethoprim in sediment and soil samples

The everyday use of various pharmaceuticals to treat humans or animals means that they are increasingly found in the environment. Contamination of the soil can cause the active ingredients to be strongly sorbed to the soil or sediment. In the worst case, they can also be expected to occur in the aquatic environment due to their different polarity. In this study, four drugs from different therapeutic classes (trimetoprim, memantine, cefdinir, praziquantel) were used in dissolved form in two sediment and three soil samples to obtain data that can describe their fate and behavior in the environment. The sorption affinities of the pharmaceuticals were described using linear, Freundlich and Dubinin-Radushkevich sorption isotherms. The highest K_d values were obtained for cefdinir, while memantine and praziquantel tended to be present in water due to their very low sorption coefficients. The studied influence of pH showed a negative trend for memantine and trimetoprim, while an increase in ionic strength resulted in higher K_d values for all drugs. The sorption mechanism for all tested samples was best described by the pseudo-secondary kinetic model (R² > 0.9999).

Coral-inspired environmental durability aerogels for micron-size plastic particles removal in the aquatic environment

Removing microplastics (MPs) from water has been a huge challenge due to their inherent features including small size and high stability. In this research, inspired by the active adsorption and passive adhesion mechanisms of corals to MPs, a new strategy to fabricate polydopamine enhanced magnetic chitosan (PDA-MCS) aerogels was developed with a target to match the surface properties of MPs, achieving high MPs removal efficiency. PDA-MCS aerogels were highly efficient in adsorbing polyethylene terephthalate (PET) microplastics in water at pH values of 6-9, with a removal efficiency of up to 91.6%. Even after three recycles, PDA-MCS aerogels still displayed comparatively high removal efficiency (83.4%). Kinetic and isothermal experiments showed that the adsorption process was the result of electrostatic interactions and physical adhesion between aerogels and microplastics. Moreover, PDA-MCS aerogels maintained high removal efficiency under simulated environmental conditions, and the removal efficiency of PET, polyethylene (PE) and polystyrene (PS) microplastics in waters reached 97.3%, 94.6%, and 92.3%, respectively. Therefore, high-efficiency environmentally durable aerogels adsorbent materials have the potential for the removal of MPs from the aquatic environment.

Adsorption removal and photocatalytic degradation of azithromycin from aqueous solution using PAC/Fe/Ag/Zn nanocomposite

The improper use of antibiotics and their discharge into the environment can have serious and hazardous consequences. The purpose of this research is to synthesize an activated carbon impregnated magnetite composite (PAC/Fe), prepare PAC/Fe/Ag/Zn nanocomposites, and innovate by simultaneously synthesizing two metals, zinc and silver, on magnetically activated carbon and check its ability to remove azithromycin antibiotic (AZT) from an aqueous solution via UV system. PAC/Fe/Ag/Zn nanocomposites were characterized by various techniques including XRD, FESEM, and EDX. A series of batch experiments were carried out under various experimental conditions such as pH of the solution (3-11), contact time (0-120 min), initial concentration of AZT (10-40 ppm), amount of PAC/Fe/Ag/Zn nano-absorbent (0.01-0.04 g/l), and recoverability and reuse. Some common isotherm models were used for the study of AZT adsorption removal and finding the best model. Also, kinetic studies of AZT removal were performed by fitting the experimental data on first-order and second-order models. In this system, under optimal conditions of pH = 9, 120 min with 0.04 g/l of PAC/Fe/Ag/Zn, 99.5% of 10 ppm AZT were degraded under UV-C irradiation. Furthermore, the obtained results of isotherm and kinetic studies revealed that Langmuir (R² = 0.9336) isotherm model, and the pseudo-first-order kinetic model (R² = 0.9826) had the highest correlation with the experimental data of AZT antibiotic adsorption. Finally, the reusability experiments showed that PAC/Fe/Ag/Zn nanocomposites have a high ability of antibiotic adsorption and high stability after four cycles of application (99.5 to 40%).

Preparation of Amino-Functionalized Mesoporous SBA-15 Nanoparticles and the Improved Adsorption of Tannic Acid in Wastewater

Ordered mesoporous Santa Barbara amorphous (SBA-15) materials have high surface areas and are widely used in adsorption, separation, filtration, and heterogeneous catalytic processes. However, SBA-15 surfaces contain hydroxyl groups that are unsuited to the adsorption of organic pollutants; thus, SBA-15 must be chemically modified to promote its adsorption activity. In this study, amino-functionalized nanoporous SBA-15 was fabricated by employing sodium silicate as a precursor. The structural characteristics of the prepared composites were examined using thermogravimetric analysis, X-ray diffraction, Fourier transform infrared spectrometry, field-emission scanning electron microscopy, transmission electron microscopy, and surface area analysis. The prepared SBA-15 had a large pore size (6.46–7.60 nm), large pore volume (1.037–1.105 cm³/g), and high surface area (546–766 m²/g). Functionalization caused a reduction in the SBA-15 pore volume and surface area, whereas amino groups that promoted an interaction between adsorbates and solids facilitated solute adsorption. The adsorption of tannic acid (TA) onto amino-modified silica composites (SBA-15 and 3-aminopropyltriethoxysilane (SBA-15/APTES) and SBA-15 and pentaethylenehexamine (SBA-15/PEHA)) was studied. Their adsorption capacities were affected by solution temperature, solution pH, agitation speed, adsorbent dosage, and initial TA concentration. The maximum adsorption capacities for SBA-15/APTES and SBA-15/PEHA were 485.18 and 413.33 mg/g, respectively, with SBA-15/APTES exhibiting ultrafast removal of TA (98.61% removal rate at 15 min). In addition, this study explored the thermodynamics, adsorption isotherms, and kinetics. A comparison of two types of amino-functionalized SBA-15 was used for the first time to adsorb TA, which providing valuable information on TA adsorption on high adsorption capacity materials in water media.

Preparation and characterization of lignin-derived hard templated carbon(s): Statistical optimization and methyl orange adsorption isotherm studies

In this study, lignin-derived zeolite templated carbon materials were fabricated to remove the organic contaminant, methyl orange. Response surface methodology with Box-Behnken design was used to optimize the adsorption parameters. Based on Box-Behnken design, a quadratic model was developed to correlate the adsorption variables with the response, removal efficiency. Analysis of variance revealed the adsorbent dosage as the most influential adsorption variable. Lignin derived ZSM-5 (PZ) and mordenite (PM) templated carbon materials exhibited high surface area; 476.0 and 716.0 m²/g respectively. The maximum theoretical adsorption capacity of PZ and PM for methyl orange was 514.0 and 225.0 mg/g, respectively. The experimental kinetic data best fitted to pseudo-second-order model for both the adsorbents. PZ adsorbent was also utilized to treat real wastewater containing dyes and achieved 40 % methyl orange removal efficiency. Adsorption thermodynamic study revealed the process as spontaneous, exothermic and also indicated the increment in entropy after adsorption.

A Review of Caffeine Adsorption Studies onto Various Types of Adsorbents

A systematic literature review of publications from 2000 to 2020 was carried out to identify research trends on adsorbent materials for the removal of caffeine from aqueous solutions. Publications were retrieved from three databases (Scopus, Web of Science, and Google Scholar). Words "adsorption AND caffeine" were examined into titles, abstracts, and keywords. A brief bibliometric analysis was performed with emphasis on the type of publication and of most cited articles. Materials for the removal of caffeine were classified according to the type of material into three main groups: organic, inorganic, and composites, each of them subdivided into different subgroups consistent with their origin or production. Tables resume for each subgroup of adsorbents the key information: specific surface area, dose, pH, maximum adsorption capacity, and isotherm models for the removal of caffeine. The highest adsorption capacities were achieved by organic adsorbents, specifically those with granular activated carbon (1961.3 mg/g) and grape stalk activated carbon (916.7 mg/g). Phenyl-phosphate-based porous organic polymer (301 mg/g), natural sandy loam sediment (221.2 mg/g), composites of MCM-48 encapsulated graphene oxide (153.8 mg/g), and organically modified clay (143.7 mg/g) showed adsorption capacities lower than those of activated carbons. In some activated carbons, a relation between the specific surface area (SSA) and the maximum adsorption capacity (Q max) was found.