Wastewater treatment and fouling control in an electro algae-activated sludge membrane bioreactor

Mini critical review: Membrane fouling control in membrane bioreactors by microalgae

Membrane bioreactors (MBRs) hold significant promise for wastewater treatment, yet the persistent challenge of membrane fouling impedes their practical application. One promising solution lies in the synergy between microalgae and bacteria, offering efficient nutrient removal, reduced energy consumption, and potential mitigation of extracellular polymeric substances (EPS) concentrations. Inoculating microalgae presents a promising avenue to address membrane fouling in MBRs. This review marks the first exploration of utilizing microalgae for membrane fouling control in MBR systems. The review begins with a comprehensive overview of the evolution and distinctive traits of microalgae-MBRs. It goes further insight into the performance and underlying mechanisms facilitating the reduction of membrane fouling through microalgae intervention. Moreover, the review not only identifies the challenges inherent in employing microalgae for membrane fouling control in MBRs but also illuminates prospective pathways for future advancement in this burgeoning field.

Mechanisms and Strategies of Advanced Oxidation Processes for Membrane Fouling Control in MBRs: Membrane-Foulant Removal versus Mixed-Liquor Improvement

Membrane bioreactors (MBRs) are well-established and widely utilized technologies with substantial large-scale plants around the world for municipal and industrial wastewater treatment. Despite their widespread adoption, membrane fouling presents a significant impediment to the broader application of MBRs, necessitating ongoing research and development of effective antifouling strategies. As highly promising, efficient, and environmentally friendly chemical methods for water and wastewater treatment, advanced oxidation processes (AOPs) have demonstrated exceptional competence in the degradation of pollutants and inactivation of bacteria in aqueous environments, exhibiting considerable potential in controlling membrane fouling in MBRs through direct membrane foulant removal (MFR) and indirect mixed-liquor improvement (MLI). Recent proliferation of research on AOPs-based antifouling technologies has catalyzed revolutionary advancements in traditional antifouling methods in MBRs, shedding new light on antifouling mechanisms. To keep pace with the rapid evolution of MBRs, there is an urgent need for a comprehensive summary and discussion of the antifouling advances of AOPs in MBRs, particularly with a focus on understanding the realizing pathways of MFR and MLI. In this critical review, we emphasize the superiority and feasibility of implementing AOPs-based antifouling technologies in MBRs. Moreover, we systematically overview antifouling mechanisms and strategies, such as membrane modification and cleaning for MFR, as well as pretreatment and in-situ treatment for MLI, based on specific AOPs including electrochemical oxidation, photocatalysis, Fenton, and ozonation. Furthermore, we provide recommendations for selecting antifouling strategies (MFR or MLI) in MBRs, along with proposed regulatory measures for specific AOPs-based technologies according to the operational conditions and energy consumption of MBRs. Finally, we highlight future research prospects rooted in the existing application challenges of AOPs in MBRs, including low antifouling efficiency, elevated additional costs, production of metal sludge, and potential damage to polymeric membranes. The fundamental insights presented in this review aim to elevate research interest and ignite innovative thinking regarding the design, improvement, and deployment of AOPs-based antifouling approaches in MBRs, thereby advancing the extensive utilization of membrane-separation technology in the field of wastewater treatment.

Principles and research progress of physical prevention and control technologies for algae in eutrophic water

The abnormal reproduction of algae in water worldwide is prominent in the context of human interference and global climate change. This study first thoroughly analyzed the effects of physical factors, such as light, temperature, hydrodynamics, and operational strategies, on algal growth and their mechanisms. Physical control techniques are safe and have great potential for preventing abnormal algal blooms in the absence of chemical reagents. The focus was on the principles and possible engineering applications of physical shading, ultrasound, micro-current, and ultraviolet (UV) technologies, in controlling abnormal algal reproduction. Physical shading can inhibit or weaken photosynthesis in algae, thereby inhibiting their growth. Ultrasound mainly affects the physiological and biochemical activities of cells by destroying the cell walls, air cells, and active enzymes. Micro-currents destroy the algal cell structure through direct and indirect oxidation, leading to algal cell death. UV irradiation can damage DNA, causing organisms to be unable to reproduce or algal cells to die directly. This article comprehensively summarizes and analyzes the advantages of physical prevention and control technologies for the abnormal reproduction of algae, providing a scientific basis for future research. In the future, attempts will be made toward appropriately and comprehensively utilizing various physical technologies to control algal blooms. The establishment of an intelligent, comprehensive physical prevention and control system to achieve environmentally friendly, economical, and effective physical prevention and control of algae, such as the South-to-North Water Diversion Project in China, is of great importance for specific waters.

Metagenomic analysis of microbial consortia native to the Amazon, Highlands, and Galapagos regions of Ecuador with potential for wastewater remediation

Native microbial consortia have been proposed for biological wastewater treatment, but their diversity and function remain poorly understood. This study investigated three native microalgae-bacteria consortia collected from the Amazon, Highlands, and Galapagos regions of Ecuador to assess their metagenomes and wastewater remediation potential. The consortia were evaluated for 12 days under light (LC) and continuous dark conditions (CDC) to measure their capacity for nutrient and organic matter removal from synthetic wastewater (SWW). Overall, all three consortia demonstrated higher nutrient removal efficiencies under LC than CDC, with the Amazon and Galapagos consortia outperforming the Highlands consortium in nutrient removal capabilities. Despite differences in α- and β-diversity, microbial species diversity within and between consortia did not directly correlate with their nutrient removal capabilities. However, all three consortia were enriched with core taxonomic groups associated with wastewater remediation activities. Our analyses further revealed higher abundances for nutrient removing microorganisms in the Amazon and Galapagos consortia compared with the Highland consortium. Finally, this study also uncovered the contribution of novel microbial groups that enhance wastewater bioremediation processes. These groups have not previously been reported as part of the core microbial groups commonly found in wastewater communities, thereby highlighting the potential of investigating microbial consortia isolated from ecosystems of megadiverse countries like Ecuador.

Insights into the growth and biochemical defense responses associated with fenitrothion toxicity and uptake by freshwater cyanobacteria

The extensive use of fenitrothion (FNT) in agricultural practices induces its persistence in soil and waterways. Therefore, it is essential to implement effective management practices such as using cyanobacteria for FNT removal and accumulation, particularly under accidental contamination. To this end, we evaluated the responses of two freshwater cyanobacteria taxa, Nostoc muscorum and Anabaena laxa to mild (7.5 mg L-1) and high (15 mg L-1) levels of FNT over a period of 7 d. Compared to N. muscorum, A. laxa was more tolerant to FNT, exhibiting higher FNT uptake and removal efficiencies at mild (16.3%) and high (17.5%) levels. FNT induced a dose-dependent decrease in cell growth, Chl a, phosphoenolpyruvate carboxylase and ribulose-1,5-bisphosphate carboxylase/oxygenase activities, which were more pronounced in N. muscorum. Moreover, FNT significantly increased oxidative damage markers i.e., increased lipid peroxidation (MDA), protein oxidation, H2O2 levels and NADPH oxidase enzyme activity, to more extent in N. muscorum. Compared to N. muscorum, A. laxa had high antioxidant capacity (FRAP), glutathione and increased activities of glutathione-S-transferase, glutathione reductase, glutathione peroxidase and superoxide dismutase, suggesting a robust antioxidant defense mechanism to mitigate FNT toxicity. However, N. muscorum devoted the induction of ascorbate content and the activity of catalase, peroxidase, monodehydroascorbate reductase, ascorbate peroxidase, and dehydroascorbate reductase enzymes. Although A. laxa had greater intracellular FNT, it experienced less FNT-induced oxidative stress, likely due to over production of antioxidants. Consequently, A. laxa is considered as a promising candidate for FNT phycoremediation. Our findings provide fundamental information on species-specific toxicity of FNT among cyanobacteria and the environmental risk of FNT toxicity in aquatic environments.

Biological performance and membrane fouling of a microalgal-bacterial membrane photobioreactor for wastewater treatment without external aeration and carbonation

Biological nutrient removal processes involving the use of activated sludge (AS) to treat municipal wastewater normally result in high aeration energy consumption and significant greenhouse gas (GHG) emissions. Therefore, developing cost-efficient and environmentally friendly processes for wastewater treatment is vital. In this work, a novel non-aerated microalgal-bacterial membrane photobioreactor (MB-MPBR) was proposed, and its feasibility for organic contaminant and nutrient removals was evaluated, for the first time. The effects of inoculation ratio (microalgae to bacteria (M/B)) on the biological performance and membrane fouling were systematically investigated. The results showed that 95.9% of the chemical oxygen demand (COD), 74.5% of total nitrogen (TN), 98.5% of NH4+-N and 42.0% of total phosphorus (TP) were removed at an inoculation M/B ratio of 3:2 at steady state, representing a significant improvement compared to the M/B inoculation ratio of 1:3. Additionally, the higher inoculation M/B ratio (3:2) significantly promoted the biomass production owing to the favorable mutual exchange of oxygen and carbon dioxide between microalgae and bacteria. Cake layer formation was the primary fouling mechanism owing to the absence of aeration scouring on the membrane surface. The membrane fouling rate was slightly higher at the higher inoculation ratio (M/B = 3:2) owing to the increased biomass and extracellular polymeric substances (EPS) productions, despite the larger particle size. These results demonstrated that the non-aerated MB-MPBR could achieve superior biological performance, of which the inoculation M/B ratio was of critical importance for the initiation and maintenance of microalgal-bacterial symbiotic system, yet possibly caused severer membrane fouling in the absence of external aeration and carbonation. This study provides a new perspective for further optimizing and applying non-aerated MB-MPBR to enhance municipal wastewater treatment.

Carbon neutrality in wastewater treatment plants: An integrated biotechnological-based solution for nutrients recovery, odour abatement and CO2 conversion in alternative energy drivers

Wastewater treatment plants play a crucial role in water security and sanitation, ensuring ecosystems balance and avoiding significant negative effects on humans and environment. However, they determine also negative pressures, including greenhouse gas and odourous emissions, which should be minimized to mitigate climate changes besides avoiding complaints. The research has been focused on the validation of an innovative integrated biological system for the sustainable treatment of complex gaseous emissions from wastewater treatment plants. The proposed system consists of a moving bed biofilm reactor coupled with an algal photobioreactor, with the dual objective of: i) reducing the inlet concentration of the odourous contaminants (in this case, hydrogen sulphide, toluene and p-xylene); ii) capturing and converting the carbon dioxide emissions produced by the degradation process into exploitable algal biomass. The first reactor promoted the degradation of chemical compounds up to 99.57% for an inlet load (IL) of 22.97 g m-3 d-1 while the second allowed the capture of the CO2 resulting from the degradation of gaseous compounds, with biofixation rate up to 81.55%. The absorbed CO2 was converted in valuable feedstocks, with a maximum algal biomass productivity in aPBR of 0.22 g L-1 d-1. Dairy wastewater has been used as alternative nutrient source for both reactors, with a view of reusing wastewater while cultivating biomass, framing the proposed technology in a context of a biorefinery within a circular economy perspective. The biomass produced in the algal photobioreactor was indeed characterized by a high lipid content, with a maximum percentage of lipids per dry weight biomass of 35%. The biomass can therefore be exploited for the production of alternative and clean energy carrier. The proposed biotechnology represents an effective tool for shifiting the conventional plants in carbon neutral platform for implementing principles of ecological transition while achieving high levels of environmental protection.

Membrane processes enhanced by various forms of physical energy: A systematic review on mechanisms, implementation, application and energy efficiency

Membrane technologies in water and wastewater treatment have been eagerly pursued over the past decades, yet membrane fouling remains the major bottleneck to overcome. Membrane fouling control methods which couple membrane processes with online in situ application of external physical energy input (EPEI) are getting closer and closer to reality, thanks to recent advances in novel materials and energy deliverance methods. In this review, we summarized recent studies on membrane fouling control techniques that depend on (i) electric field, (ii) acoustic field, (iii) magnetic field, and (iv) photo-irradiation (mostly ultraviolet or visible light). Mechanisms of each energy input were first reported, which defines the applicability of these methods to certain wastewater matrices. Then, means of implementation were discussed to evaluate the compatibility of these fouling control methods with established membrane techniques. After that, preferred applications of each energy input to different foulant types and membrane processes in the experiment reports were summarized, along with a discussion on the trends and knowledge gaps of such fouling control research. Next, specific energy consumption in membrane fouling control and flux enhancement was estimated and compared, based on the experimental results reported in the literature. Lastly, strength and weakness of these methods and future perspectives were presented as open questions.

Research progress of electrically-enhanced membrane bioreactor (EMBR) in pollutants removal and membrane fouling alleviation

Membrane bioreactor (MBR), as a biological unit for wastewater treatment, has been proven to have the advantages of simple structure and high pollutant removal rate. However, membrane fouling limits its wide application, and it is crucial to adopt effective membrane fouling control methods. As a new type of membrane fouling control technology, electrically-enhanced MBR (EMBR) has attracted more interest recently. It uses the driving force of electric field to make pollutants flocculate or move away from the membrane surface to achieve the purpose of inhibiting membrane fouling. This paper expounds the configuration of EMBR in recent years, including the location of membrane components, the way of electric field application and the selection of electrode and membrane materials, and provides the latest development information in various aspects. The enhanced effect of electric field on the removal of comprehensive and refractory pollutants is outlined in detail. And from the perspective of sludge properties (EPS, SMP, sludge particle size, zeta potential and microbial activity), the influence of electric field on sludge characteristics and the relationship between the changes of sludge properties in EMBR and membrane fouling are discussed. Moreover, the electrochemical mechanisms of electric field alleviating membrane fouling are elucidated from electrophoresis, electrostatic repulsion, electroflocculation, electroosmosis, and electrochemical oxidation, and the regeneration and stability of EMBR are assessed. The existing challenges and future research directions are also proposed. This review could provide theoretical guidance and further studies for subsequent topic, and promoting the wide engineering applications of EMBR.

Advanced treatment of toluene emissions with a cutting-edge algal bacterial photo-bioreactor: Performance assessment in a circular economy perspective

A novel approach for the treatment of VOCs (by using toluene used as a model compound) and the simultaneous conversion of carbon dioxide into valuable biomass has been investigated by using a combination of an activated sludge moving bed bioreactor (MBBR) and an algal photo-bioreactor (PBR). The first unit (MBBR, R1) promoted toluene removal up to 99.9 % for inlet load (IL) of 119.91 g m^-3 d^-1. The CO₂ resulting from the degradation of toluene was then fixed in PBR (R2), with a fixation rate up to 95.8 %. The CO₂ uptake was promoted by algae, with average production of algal biomass in Stage VI of 1.3 g L^-1 d^-1. In the contest of the circular economy, alternative sources of nutrients have been assessed, using synthetic urban wastewater (UWW) and dairy wastewater (DWW) for liquid renewal. The produced biomass with DWW showed a high lipid content, with a maximum productivity of 450.25 mg of lipids L^-1 d^-1. The solution proposed may be thus regarded as a sustainable and profitable strategy for VOCs treatment in a circular economy perspective.

Cyanobacteria as a Valuable Natural Resource for Improved Agriculture, Environment, and Plant Protection

Taking into consideration, the challenges faced by the environment and agro-ecosystem make increased for suggestions more reliable methods to help increase food security and deal with difficult environmental problems. Environmental factors play a critical role in the growth, development, and productivity of crop plants. Unfavorable changes in these factors, such as abiotic stresses, can result in plant growth deficiencies, yield reductions, long-lasting damage, and even death of the plants. In reflection of this, cyanobacteria are now considered important microorganisms that can improve the fertility of soils and the productivity of crop plants due to their different features like photosynthesis, great biomass yield, ability to fix the atmospheric N2, capability to grow on non-arable lands, and varied water sources. Furthermore, numerous cyanobacteria consist of biologically active substances like pigments, amino acids, polysaccharides, phytohormones, and vitamins that support plant growth enhancement. Many studies have exposed the probable role of these compounds in the alleviation of abiotic stress in crop plants and have concluded with evidence of physiological, biochemical, and molecular mechanisms that confirm that cyanobacteria can decrease the stress and induce plant growth. This review discussed the promising effects of cyanobacteria and their possible mode of action to control the growth and development of crop plants as an effective method to overcome different stresses.

Graphical Abstract

Living membrane bioreactor for highly effective and eco-friendly treatment of textile wastewater

The treatability of synthetic textile wastewater containing model dyes, such as reactive black and direct black dye (25.0 ± 2.6 mg_dye/L), with chemical oxygen demand (COD, 1000 ± 113 mg/L), ammonia‑nitrogen (NH₃-N, 140 ± 97 mg/L) and sulphate ions (SO₄^2-, 1357 ± 10.86 mg/L) was investigated in this study using an innovative living membrane bioreactor (LMBR) using an encapsulated self-forming dynamic membrane (ESFDM). The key advantage of ESFDMBR is the self-forming of the biological filtering layer protected between two meshes of inert robust and inexpensive material. A laboratory scale bioreactor (BR) equipped with a filtering unit mounting polyester meshes with a pore size of 30 μm, operated at an influent flux of 30 LMH was thus used. After the formation of the biological living membrane (LM), the treatment significantly reduced COD and DOC concentrations to the average values of 34 ± 10 mg/L and 32 ± 7 mg/L, corresponding to reduction efficiencies of 96.0 ± 1.1 % and 94 ± 1.05 %, respectively. Throughout the LMBR operation, the colours were successfully removed from synthetic textile wastewater with an overall removal efficiency of about 85.0 ± 1.8 and 86.0 ± 1.9 % for direct and reactive dyes, respectively. In addition, the proposed system was also found effective in affording removal efficiency of ammonia (NH₃) of 97 ± 0.5 %. Finally, this treatment afforded circa 40.7 ± 5.8 % sulphate removal, with a final concentration value of 805 ± 78.61 mg/L. The innovative living membrane, based on an encapsulated self-forming dynamic membrane allows a prolonged containment of the membrane fouling, confirmed by investigating the concentration of membrane fouling precursors and the time-course variations of turbidity and transmembrane pressure (TMP). Those final concentrations of wastewater pollutants were found to be below the limits for admission of the effluents in public sanitation networks in Italy and Tunisia, as representative countries for the regulation in force in Europe and North Africa. In conclusion, due to the low costs of plant and maintenance, the simple applicability, the rapid online implementation, the application of LMBR results in a promising method for the treatment of textile wastewater.

Near dissolved organic matter microfiltration (NDOM MF) coupled with UVC LED disinfection to maximize the efficiency of water treatment for the removal of Giardia and Cryptosporidium

Microfiltration (MF) membranes with a mean pore size same as or smaller than 0.45 µm have been typically used to separate pathogenic protozoa in water since materials larger than 0.45 µm are considered particulates. However, 0.45 µm is too small to separate protozoa which are 4-6 µm (Cryptosporidium oocyst) or 8-15 µm (Giardia cyst) in size. In this study, we optimized the mean pore size of MF membranes to maximize the producibility and guarantee a high removal rate simultaneously and proposed the membrane filtration using an MF membrane with an optimum mean pore size larger than but close to dissolved organic matter (DOM), which is called near DOM MF (NDOM MF). According to the MF test using polystyrene surrogate beads with diameters of 3 and 8 µm, an MF membrane with a 0.8 µm mean pore size was the best in that it showed 52% to 146% higher water fluxes than a 0.45 µm MF membrane while maintaining the removal rate at 3-4 log. It was also the case for a low-temperature MF test, revealing the NDOM MF is highly effective regardless of temperature changes. Lastly, we tried to find the possibility of combining the NDOM MF with disinfection by an ultraviolet light emitting diode (UVC LED) to further guarantee the high quality of treated water while providing high process efficiency.

Bioremediation of Wastewater Using Yeast Strains: An Assessment of Contaminant Removal Efficiency

The main goal of wastewater treatment is to significantly reduce organic compounds, micronutrients (nitrogen and phosphorus) and heavy metals and other contaminants (pathogens, pharmaceuticals and industrial chemicals). In this work, the efficiency of removing different contaminants (COD, NO₃^-, NO₂^-, NH₄⁺, PO₄^3-, SO₄^2-, Pb²⁺, Cd²⁺) from synthetic wastewater was tested using five different yeast strains: Kluyveromyces marxianus CMGBP16 (P1), Saccharomyces cerevisiae S228C (P2), Saccharomyces cerevisiae CM6B70 (P3), Saccharomyces cerevisiae CMGB234 (P4) and Pichia anomala CMGB88 (P5). The results showed a removal efficiency of up to 70% of COD, 97% of nitrate, 80% of nitrite, 93% of phosphate and 70% of sulfate ions for synthetic wastewater contaminated with Pb²⁺ (43 mg/L) and Cd²⁺ ions (39 mg/L). In contrast, the results showed an increase in ammonium ions, especially in the presence of Pb²⁺ ions. The yeast strains showed a high capacity to reduce Pb²⁺ (up to 96%) and Cd²⁺ (up to 40%) ions compared to the initial concentrations. In presence of a crude biosurfactant, the removal efficiency increased up to 99% for Pb²⁺ and 56% for Cd²⁺ simultaneously with an increase in yeast biomass of up to 11 times. The results, which were obtained in the absence of aeration and in neutral pH conditions, proved a high potential for practical applications in the biotreatment of the wastewater and the recovery of Pb and Cd ions, with a high benefit-cost ratio.

Modification of reinforced hollow fiber membranes with WO3 nanosheets for treatment of textile wastewater by membrane bioreactor

In this study, performance of braid reinforced hollow fiber membrane containing polyvinylidene fluoride (PVDF) embedded with tungsten trioxide (WO₃) nanosheets in a membrane bioreactor (MBR) was examined for textile wastewater treatment. The WO₃ nanosheets was synthesized and blended at different concentrations (0.1-0.02 wt%) in casting solutions of the membranes. The WO₃ nanosheets characterized using various tests such as XRD, FTIR, SEM, EDS, dot-mapping, and TEM. Furthermore, the effects of the increased WO₃ nanosheets into the PVDF matrix on the membrane morphology, hydrophilicity, permeability, antifouling, and COD and color removal efficiency was investigated. The addition of 0.1 wt% of the nanosheets reduces the water contact angle from 69.3° to 62.5° while increasing overall porosity from 37.5 to 43.2%. COD and color removal for PVDF/0.10 wt% WO₃ membrane was between 86-89% and 72-76%, respectively. While the TMP of modified WO₃ membranes did not significantly increase due to antimicrobial properties of the WO₃ nanosheets, the TMP of the pure PVDF membrane increase, indicating considerable cake layer fouling. The results of this study showed that modification of PVDF braid reinforced hollow fiber membrane using WO₃ nanosheets is promising membrane for MBR systems.

Microalgae-based wastewater treatment: Mechanisms, challenges, recent advances, and future prospects

The rapid expansion of both the global economy and the human population has led to a shortage of water resources suitable for direct human consumption. As a result, water remediation will inexorably become the primary focus on a global scale. Microalgae can be grown in various types of wastewaters (WW). They have a high potential to remove contaminants from the effluents of industries and urban areas. This review focuses on recent advances on WW remediation through microalgae cultivation. Attention has already been paid to microalgae-based wastewater treatment (WWT) due to its low energy requirements, the strong ability of microalgae to thrive under diverse environmental conditions, and the potential to transform WW nutrients into high-value compounds. It turned out that microalgae-based WWT is an economical and sustainable solution. Moreover, different types of toxins are removed by microalgae through biosorption, bioaccumulation, and biodegradation processes. Examples are toxins from agricultural runoffs and textile and pharmaceutical industrial effluents. Microalgae have the potential to mitigate carbon dioxide and make use of the micronutrients that are present in the effluents. This review paper highlights the application of microalgae in WW remediation and the remediation of diverse types of pollutants commonly present in WW through different mechanisms, simultaneous resource recovery, and efficient microalgae-based co-culturing systems along with bottlenecks and prospects.

Microalgae-Enabled Wastewater Remediation and Nutrient Recovery through Membrane Photobioreactors: Recent Achievements and Future Perspective

The use of microalgae for wastewater remediation and nutrient recovery answers the call for a circular bioeconomy, which involves waste resource utilization and ecosystem protection. The integration of microalgae cultivation and wastewater treatment has been proposed as a promising strategy to tackle the issues of water and energy source depletions. Specifically, microalgae-enabled wastewater treatment offers an opportunity to simultaneously implement wastewater remediation and valuable biomass production. As a versatile technology, membrane-based processes have been increasingly explored for the integration of microalgae-based wastewater remediation. This review provides a literature survey and discussion of recent progressions and achievements made in the development of membrane photobioreactors (MPBRs) for wastewater treatment and nutrient recovery. The opportunities of using microalgae-based wastewater treatment as an interesting option to manage effluents that contain high levels of nutrients are explored. The innovations made in the design of membrane photobioreactors and their performances are evaluated. The achievements pave a way for the effective and practical implementation of membrane technology in large-scale microalgae-enabled wastewater remediation and nutrient recovery processes.

CO2 bio-mitigation using genetically modified algae and biofuel production towards a carbon net-zero society

CO₂ sequestration carried by biological methodologies shows enhanced potential and has the advantage that biomass produced from the captured CO₂ can be used for different applications. Bio-mitigation of carbons through a micro-algal system addresses a promising and feasible option. This review mostly focused on the role of algae, particular mechanisms, bioreactors in algae cultivation, and genetically modified algae in CO₂ fixation and energy generation systems. A combination of CO₂ bio-mitigation and biofuel production might deliver an extremely promising alternative to current CO₂ mitigation systems. Bio mitigation in which the excess carbon is captured and bio fixation which the carbon is captured by algae or autotrophs and used for producing biofuel. This review revealed that steps for biofuel production from algae include factors affecting, harvesting techniques, oil extraction and transesterification. This review helps environmentalists and researchers to assess the effect of algae-based biorefinery on the green environment.

Nutrient and organic pollutants removal in synthetic wastewater by Pseudomonas aeruginosa and Chryseobacterium sp./biofilter systems

Nutrient and organic pollution raise serious problems for aquatic ecosystems through the accumulation of organic carbon, the reduction of light penetration, and the loss of submerged aquatic vegetation. The over-enrichment of water with nitrogen and phosphorus leads to an imbalance in nutrient ratios, creating favorable conditions for toxic algal blooms, formation of oxygen-depleted water, etc. Thus, developing new technological solutions to reduce their amount is imperative. The present study investigates the capacity of Pseudomonas aeruginosa and Chryseobacterium sp. bacterial strains to form biofilm on solid support (biofilter), both individually and in tandem, using various analytical techniques. Also, the biofilm/biofilter systems' efficiency in removing nutrients such as nitrate, nitrite, ammonium, and phosphate ions from municipal wastewaters is assessed. The results showed a reduction of nutrient pollution of up to 91%, 98%, 55%, and 71% for nitrite, nitrate, ammonium, and phosphate ions. A reduction of about 78% of COD was also observed. The results were obtained in the absence of an additional aeration process, thus having a great potential for reducing total costs of wastewater treatment and developing ecological systems for wastewater management.

Harnessing photosynthesis to produce electricity using cyanobacteria, green algae, seaweeds and plants

The conversion of solar energy into electrical current by photosynthetic organisms has the potential to produce clean energy. Life on earth depends on photosynthesis, the major mechanism for biological conversion of light energy into chemical energy. Indeed, billions of years of evolution and adaptation to extreme environmental habitats have resulted in highly efficient light-harvesting and photochemical systems in the photosynthetic organisms that can be found in almost every ecological habitat of our world. In harnessing photosynthesis to produce green energy, the native photosynthetic system is interfaced with electrodes and electron mediators to yield bio-photoelectrochemical cells (BPECs) that transform light energy into electrical power. BPECs utilizing plants, seaweeds, unicellular photosynthetic microorganisms, thylakoid membranes or purified complexes, have been studied in attempts to construct efficient and non-polluting BPECs to produce electricity or hydrogen for use as green energy. The high efficiency of photosynthetic light-harvesting and energy production in the mostly unpolluting processes that make use of water and CO₂ and produce oxygen beckons us to develop this approach. On the other hand, the need to use physiological conditions, the sensitivity to photoinhibition as well as other abiotic stresses, and the requirement to extract electrons from the system are challenging. In this review, we describe the principles and methods of the different kinds of BPECs that use natural photosynthesis, with an emphasis on BPECs containing living oxygenic photosynthetic organisms. We start with a brief summary of BPECs that use purified photosynthetic complexes. This strategy has produced high-efficiency BPECs. However, the lifetimes of operation of these BPECs are limited, and the preparation is laborious and expensive. We then describe the use of thylakoid membranes in BPECs which requires less effort and usually produces high currents but still suffers from the lack of ability to self-repair damage caused by photoinhibition. This obstacle of the utilization of photosynthetic systems can be significantly reduced by using intact living organisms in the BPEC. We thus describe here progress in developing BPECs that make use of cyanobacteria, green algae, seaweeds and higher plants. Finally, we discuss the future challenges of producing high and longtime operating BPECs for practical use.

Degradation of gaseous volatile organic compounds (VOCs) by a novel UV-ozone technology

In this study, a UV-assisted ozonation (UV/O₃) process for the degradation of VOCs emissions with a final scrubbing phase was implemented to evaluate the removal efficiency of toluene and to prevent the release of polluting intermediates of the single-step process. Inlet toluene concentration and applied voltage were varied in order to investigate several operating conditions. The results highlighted that at higher inlet concentration the abatement of toluene was lower, while increase in ozone concentration led to an increase of the degradation efficiencies. The additional water scrubbing step enhanced the abatement of UV/O₃ up to 98.5%, due to the solubilisation of ozone and by-products in the process water and, thus, the further oxidation of the contaminants within this phase. A maximum Elimination Capacity (EC_max) of 22.6 g m⁻³ h⁻¹ was achieved with the UV/O₃ + Scrubbing. The combined system boosted higher performance and stability compared to the stand-alone (UV/O₃) process along with a more economical and environmental sustainability.

The Biological Performance of a Novel Electrokinetic-Assisted Membrane Photobioreactor (EK-MPBR) for Wastewater Treatment

Developing an effective phycoremediation system, especially by utilizing microalgae, could provide a valuable approach in wastewater treatment for simultaneous nutrient removal and biomass generation, which would help control environmental pollution. This research aims to study the impact of low-voltage direct current (DC) application on Chlorella vulgaris properties and the removal efficiency of nutrients (N and P) in a novel electrokinetic-assisted membrane photobioreactor (EK-MPBR) in treating synthetic municipal wastewater. Two membrane photobioreactors ran in parallel for 49 days with and without an applied electric field (current density: 0.261 A/m2). Mixed liquid suspended soils (MLSS) concentration, chemical oxygen demand (COD), floc morphology, total phosphorus (TP), and total nitrogen (TN) removals were measured during the experiments. The results showed that EK-MPBR achieved biomass production comparable to the control MPBR. In EK-MPBR, an over 97% reduction in phosphate concentration was achieved compared to 41% removal in the control MPBR. The control MPBR outperformed the nitrogen removal of EK-MPBR (68% compared to 43% removal). Induced DC electric field led to lower pH, lower zeta potential, and smaller particle sizes in the EK-MPBR as compared with MPBR. The results of this novel study investigating the incorporation of Chlorella vulgar is in an electrokinetic-assisted membrane photobioreactor indicate that this is a promising technology for wastewater treatment.

State-of-the-Art Review on the Application of Membrane Bioreactors for Molecular Micro-Contaminant Removal from Aquatic Environment

In recent years, the emergence of disparate micro-contaminants in aquatic environments such as water/wastewater sources has eventuated in serious concerns about humans’ health all over the world. Membrane bioreactor (MBR) is considered a noteworthy membrane-based technology, and has been recently of great interest for the removal micro-contaminants. The prominent objective of this review paper is to provide a state-of-the-art review on the potential utilization of MBRs in the field of wastewater treatment and micro-contaminant removal from aquatic/non-aquatic environments. Moreover, the operational advantages of MBRs compared to other traditional technologies in removing disparate sorts of micro-contaminants are discussed to study the ways to increase the sustainability of a clean water supplement. Additionally, common types of micro-contaminants in water/wastewater sources are introduced and their potential detriments on humans’ well-being are presented to inform expert readers about the necessity of micro-contaminant removal. Eventually, operational challenges towards the industrial application of MBRs are presented and the authors discuss feasible future perspectives and suitable solutions to overcome these challenges.

A Review of Microalgae- and Cyanobacteria-Based Biodegradation of Organic Pollutants

This review proposes a new bioremediation method based on the diverse functionalities of algae. A greenway for cleansing wastewater is more ecologically friendly and environmentally sustainable than prior methods with other bacteria. New bioremediation technology employing algae and cyanobacteria for the removal of a wide range of organic contaminants is reasonable and has great potential. The prevalence of organic contaminants in aquatic habitats may endanger the health and well-being of several marine creatures. Agriculture, industry, and household trash are just a few of the human-caused sources of organic pollutants that contaminate waterways around the world. Before wastewater can be released into waterways, it must be cleaned. Algae-based wastewater treatment systems are becoming increasingly popular because of their environmental sustainability and lack of secondary pollutants. According to the kind of pollutant, the physicochemical properties of wastewater, and the algal species, algae and cyanobacteria can absorb and accumulate a wide spectrum of organic pollutants at different rates. In addition, phytoremediation is a cost-effective alternative to conventional treatments for degrading organic contaminants. Phycoremediationally produced algal biomass may also be an important part of the bioenergy value chain. This article focuses on microalgae and cyanobacteria species, which may remove many organic contaminants from water systems.

Innovative encapsulated self-forming dynamic bio-membrane bioreactor (ESFDMBR) for efficient wastewater treatment and fouling control

The concept of a novel living encapsulated self-forming dynamic bio-membranes (ESFDM) for an innovative wastewater treatment in membrane bioreactor (MBR) is presented in the current study. The active filtering membrane is encapsulated, and thus stabilized, between two support meshes with pore in micrometer size. The combination of activated sludge, the ESFDM and the cake layer formed external to the filtering module contributed to the treatment of municipal wastewater. COD concentration reductions (average value of 95.55 ± 1.44%) by ESFDM bioreactor (ESFDMBR) were comparable to those obtained with a previously reported membrane bioreactor (MBR), where a conventional membrane was studied under the same operating conditions. The ESFDMBR, compared to the conventional MBR, obtained higher reductions of NH₃-N, NO₃^-N and PO₄^3-P concentrations. Increased removals of nitrogen-containing nutrients were ascribed to anoxic conditions reached in the ESFDM layer protected from the aeration by the external cake layer. Rate of increase of transmembrane pressure (TMP) per day in the ESFDMBR (0.03 kPa/day) was lower than the value obtained in the previously reported conventional MBR (8.08 kPa/day). Lower concentrations of fouling precursors in combination with the effective filtration capacity of the porous living ESFDM resulted in the reduction of the fouling rate. Analysis of microbiological community revealed that the microbial community structures in the mixed liquor and ESFDM were different. The ESFDM layer promoted growth of bacteria as indicated by the higher total cell count and higher microbial diversity compared to those observed in the mixed liquor.

Full-Scale Odor Abatement Technologies in Wastewater Treatment Plants (WWTPs): A Review

The release of air pollutants from the operation of wastewater treatment plants (WWTPs) is often a cause of odor annoyance for the people living in the surrounding area. Odors have been indeed recently classified as atmospheric pollutants and are the main cause of complaints to local authorities. In this context, the implementation of effective treatment solutions is of key importance for urban water cycle management. This work presents a critical review of the state of the art of odor treatment technologies (OTTs) applied in full-scale WWTPs to address this issue. An overview of these technologies is given by discussing their strengths and weaknesses. A sensitivity analysis is presented, by considering land requirements, operational parameters and efficiencies, based on data of full-scale applications. The investment and operating costs have been reviewed with reference to the different OTTs. Biofilters and biotrickling filters represent the two most applied technologies for odor abatement at full-scale plants, due to lower costs and high removal efficiencies. An analysis of the odors emitted by the different wastewater treatment units is reported, with the aim of identifying the principal odor sources. Innovative and sustainable technologies are also presented and discussed, evaluating their potential for full-scale applicability.

Phycoremediation of wastewater for pollutant removal: A green approach to environmental protection and long-term remediation

Surface and water bodies in many parts of the world are affected due to eutrophication, contamination and depletion. The approach of wastewater treatment using algae for eliminating nutrients and other pollutants from domestic wastewater is growing interest among the researchers. However, sustainable treatment of the wastewater is considered to be important in establishing more effective nutrient and pollutant reduction using algal systems. In comparison to the conventional method of remediation, there are opportunities to commercially viable businesses interest with phycoremediation, thus by achieving cost reductions and renewable bioenergy options. Phycoremediation is an intriguing stage for treating wastewater since it provides tertiary bio-treatment while producing potentially valuable biomass that may be used for a variety of applications. Furthermore, the phycoremediation provides the ability to remove heavy metals as well as harmful organic substances, without producing secondary contamination. In this review, the role of microalgae in treating different wastewaters and the process parameters affecting the treatment and future scope of research have been discussed. Though several algae are employed for wastewater treatment, species of the genera Chlamydomonas, Chlorella, and Scenedesmus are extensively utilized. Interestingly, there is a vast scope for employing algal species with high flocculation capacity and adsorption mechanisms for the elimination of microplastics. In addition, the algal biomass generated during phycoremediation has been found to possess high protein and lipid contents, promising their exploitation in biofuel, food and animal feed industries.

Assessing effects of Ca2+ addition on membrane bioreactor performance and macro-floc sludge characteristics

Calcium ions (Ca²⁺) can trigger coagulation-flocculation process to form macro-flocculated sludge (MFS). Thus, dosing Ca²⁺-containing reagents into membrane bioreactors (MBRs) is considered as a promising approach to mitigate membrane biofouling. However, a mechanistic understanding of Ca²⁺ addition to MBR performance remains elucidated, such as physicochemical characteristics of MFS and their functionality variations. Consequently, this study was sought to understand the interplays of Ca²⁺ addition and MBR performance with a focus on characterizing MFS in detail. Three parallel MBRs were amended with 82, 208 and 410 mg-Ca²⁺/L final concentrations. Particle size analyses revealed that MFS formation was overall enhanced by the Ca²⁺ addition and granular sludge with diameters of up to 900 μm was formed in the 410 mg-Ca²⁺/L scenario. We believed that cationic bridges facilitated by elevated Ca²⁺ concentrations in conjunction with coagulation-flocculation were primary mechanisms of the formation of large flocs. Moreover, significant portions of soluble proteins and polysaccharides were flocculated and precipitated by Ca²⁺, which demonstrated a negative correlation between extracellular polymeric substances (EPS) concentrations and the formation of MFS. Furthermore, the population abundancies of Thiotrichaceae, Sphingomonadales and Hyphomicrobiaceae decreased in the sludge with Ca²⁺ addition resulted in profound changes of the microbial communities in the MBRs. But MBR performance, such as chemical oxygen demand removal (over 90%), showed no variation during the MBR operation. On the contrary, total nitrogen removal was inhibited in the MBRs. It was because the enlarging MFS formed diffusion barriers to prevent organic component from entering into the sludge flocs to be consumed.

Effective Parameters on Fabrication and Modification of Braid Hollow Fiber Membranes: A Review

Hollow fiber membranes (HFMs) possess desired properties such as high surface area, desirable filtration efficiency, high packing density relative to other configurations. Nevertheless, they are often possible to break or damage during the high-pressure cleaning and aeration process. Recently, using the braid reinforcing as support is recommended to improve the mechanical strength of HFMs. The braid hollow fiber membrane (BHFM) is capable apply under higher pressure conditions. This review investigates the fabrication parameters and the methods for the improvement of BHFM performance.

One planet, one health, one future: The environmental perspective

The final goal of the "One Health" is the control of the global health of our planet with a multidisciplinary approach that involves knowledge for different disciplines. In the near future, we could see in the same team veterinarians, doctors, and environmental experts work together to guarantee the health of our planet and one sustainable future for all.