Simple and low-cost production of magnetite/graphene nanocomposites for heavy metal ions adsorption

A thorough investigation into the adsorption behavior of sophorolipid-modified fly ash towards compound pollution of lead and tetracycline

Heavy metal ions and antibiotics were simultaneously detected in authentic water systems. This research, for the first time, employed synthesized sophorolipid-modified fly ash(SFA) to eliminate tetracycline(TC) and lead(Pb2+) from wastewater. Various characterization techniques, including SEM-EDS, FTIR, XPS, BET, and Zeta, were employed to investigate the properties of the SFA. The results showed that the sophorolipid modification significantly improved the fly ash's adsorption capacities for the target pollutants. The static adsorption experiments elucidated the adsorption behaviors of SFA towards TC and Pb2+ in single and binary systems, highlighting the effects of different Environmental factors on the adsorption behavior in both types of systems. In single systems, SFA exhibited a maximum adsorption capacity of 128.96 mg/g for Pb2+ and 55.57 mg/g for TC. The adsorption of Pb2+ and TC followed pseudo-second-order kinetics and Freundlich isotherm models. The adsorption reactions are endothermic and occur spontaneously. SFA demonstrates varying adsorption mechanisms for two different types of pollutants. In the case of Pb2+, the primary mechanisms include ion exchange, electrostatic interaction, cation-π interaction, and complexation, while TC primarily engages in hydrogen bonding, π-π interaction, and complexation. The interaction between Pb2+ and TC has been shown to improve adsorption efficiency at low concentrations. Additionally, adsorption-desorption experiments confirm the reliable cycling performance of modified fly ash, highlighting its potential as a cost-effective and efficient adsorbent for antibiotics and heavy metals.

Adsorptive removal of heavy metals from aqueous solutions: Progress of adsorbents development and their effectiveness

Increased levels of heavy metals (HMs) in aquatic environments poses serious health and ecological concerns. Hence, several approaches have been proposed to eliminate/reduce the levels of HMs before the discharge/reuse of HMs-contaminated waters. Adsorption is one of the most attractive processes for water decontamination; however, the efficiency of this process greatly depends on the choice of adsorbent. Therefore, the key aim of this article is to review the progress in the development and application of different classes of conventional and emerging adsorbents for the abatement of HMs from contaminated waters. Adsorbents that are based on activated carbon, natural materials, microbial, clay minerals, layered double hydroxides (LDHs), nano-zerovalent iron (nZVI), graphene, carbon nanotubes (CNTs), metal organic frameworks (MOFs), and zeolitic imidazolate frameworks (ZIFs) are critically reviewed, with more emphasis on the last four adsorbents and their nanocomposites since they have the potential to significantly boost the HMs removal efficiency from contaminated waters. Furthermore, the optimal process conditions to achieve efficient performance are discussed. Additionally, adsorption isotherm, kinetics, thermodynamics, mechanisms, and effects of varying adsorption process parameters have been introduced. Moreover, heavy metal removal driven by other processes such as oxidation, reduction, and precipitation that might concurrently occur in parallel with adsorption have been reviewed. The application of adsorption for the treatment of real wastewater has been also reviewed. Finally, challenges, limitations and potential areas for improvements in the adsorptive removal of HMs from contaminated waters are identified and discussed. Thus, this article serves as a comprehensive reference for the recent developments in the field of adsorptive removal of heavy metals from wastewater. The proposed future research work at the end of this review could help in addressing some of the key limitations facing this technology, and create a platform for boosting the efficiency of the adsorptive removal of heavy metals.

Fabrication of engineered biochar for remediation of toxic contaminants in soil matrices and soil valorization

Biochar has emerged as an efficacious green material for remediation of a wide spectrum of environmental pollutants. Biochar has excellent characteristics and can be used to reduce the bioavailability and leachability of emerging pollutants in soil through adsorption and other physico-chemical reactions. This paper systematically reviewed previous researches on application of biochar/engineered biochar for removal of soil contaminants, and underlying adsorption mechanism. Engineered biochar are derivatives of pristine biochar that are modified by various physico-chemical and biological procedures to improve their adsorption capacities for contaminants. This review will promote the possibility to expand the application of biochar for restoration of degraded lands in the industrial area or saline soil, and further increase the useable area. This review shows that application of biochar is a win-win strategy for recycling and utilization of waste biomass and environmental remediation. Application of biochar for remediation of contaminated soils may provide a new solution to the problem of soil pollution. However, these studies were performed mainly in a laboratory or a small scale, hence, further investigations are required to fill the research gaps and to check real-time applicability of engineered biochar on the industrial contaminated sites for its large-scale application.

Remediation of Pb(II) and Cd(II) in polluted waters with calcium thioglycolate-modified straw biochar

The pollution of water bodies by heavy metals (HMs) such as Pb(II) and Cd(II) poses a serious environmental risk. Herein, rice straw biochar (RBC) modified with calcium thioglycolate was used to remove Pb(II) and Cd(II) from aqueous solutions. The adsorption performance of the modified biochar was investigated via adsorption kinetics and isotherm model fitting. Furthermore, scanning electron microscopy (SEM), X-ray energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) were used to elucidate the modification and adsorption mechanisms. The results showed that the modification process loaded sulfur-containing functional groups, calcium carbonate, and calcium oxalate crystals on the biochar surface, considerably enhancing its complexation performance and ion-exchange capacity. The equilibrium adsorption amounts for Pb(II) and Cd(II) reached 124.92 and 65.44 mg g-1 in unary systems, respectively; they reached 121.34 and 39.43 mg g-1 in a binary Pb(II) and Cd(II), respectively. Moreover, the optimal adsorption conditions were as follows: pH = 6, temperature = 25 °C, dosage = 0.8 g L-1, and contact time = 2 h. In the binary Pb(II) and Cd(II) system, the adsorption process obeyed the Langmuir competitive adsorption model, which means that one adsorption site on the modified biochar was effective for only one heavy-metal ion, and the modified biochar was more selective for Pb(II) than for Cd(II). The adsorption mechanism, which was dominated by chemisorption, mainly involved complexation, precipitation, ion exchange, and cation-π interactions. Meanwhile, adsorption and desorption experiments indicated that the modified biochar exhibited satisfactory recycling performance, demonstrating its feasibility as an inexpensive and efficient heavy-metal adsorbent for polluted water.

In-situ conversion of geopolymer into novel floral magnetic sodalite microspheres for efficient removal of Cd(II) from water

In the present work, a novel, floral-like, magnetic sodalite microsphere (SODM) was synthesized in situ by using fly ash (FA) and metakaolin (MK) as raw materials and was used to remove Cd(II) from water. Its magnetism can solve the problems of adsorbent recovery and possible secondary pollution. During the static adsorption, SODM shows a maximum adsorption capacity of 245.17 mg/g. The adsorption of Cd(II) on the SODM surface is spontaneous, exothermic, and physicochemical adsorption, which was evaluated by thermodynamics, kinetics, and isotherm studies. During dynamic adsorption, SODM shows a maximum adsorption capacity of 342.74 mg/g in the simulated solution prepared by the deionized water, compared to 215.88 mg/g in the simulated solution prepared using Xiangsi Lake water from Guangxi Minzu University. At 0.5 g SODM dosage in the dynamic adsorption, the adsorption capacity could rise to 632.81 mg/g. These results demonstrated the excellent Cd (II) adsorption performance of the SODM. The adsorption of cadmium on the SODM surface includes the synergistic effects of electrostatic attraction, ion exchange, and surface coordination reaction. Besides, the SODM shows good regeneration performance in both the deionized water and Xiangsi Lake water. The present study explores SODM as an adsorbent for the Cd (II) removal from wastewater and unbolts the industrial applicability of the SODM in the field of wastewater purification.

New insights on the adsorption of phenol red dyes from synthetic wastewater using activated carbon/Fe2(MoO4)3

Water shortage is considered as one of the main challenges of human life. A practical solution to this problem is the wastewater treatment. The removal of dyes from wastewaters has received considerable critical attention by researchers due to their high volume and toxicity. In the current research, the adsorption of phenol red dyes from synthetic wastewater using the activated carbon produced from Mespilus germanica modified with Fe₂(MoO₄)₃ was studied. The proposed adsorbent was characterized by Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray analysis (EDX)/Map, Brunauer-Emmett-Teller (BET), and Raman techniques. The optimal adsorption operating parameters including pH, stirring rate, temperature, dosage of adsorbent, dye initial concentration, and contact time were 3, 500 rpm, 25 °C, 1 g/L, 10 mg/L, and 60 min, respectively. Furthermore, the successful regeneration of the adsorbent for 3 times, using methanol solution as a regeneration medium, denoted its capability in performing adsorption and desorption processes. Equilibrium studies showed that the adsorption of phenol red dyes by activated carbon (AC)/Fe₂(MoO₄)₃ was desirable and physical and the experimental data were fitted well by the Freundlich model. In addition, the kinetic behavior of the current adsorption process was well described by the pseudo-second-order kinetic model, while thermodynamic calculations showed that the process was exothermic and spontaneous.

Preparation of esterified biomass waste hydrogels and their removal of Pb2+, Cu2+ and Cd2+ from aqueous solution

The treatment of polluted water is a serious environmental problem in the world. Biomass is easily modified and can be prepared into adsorbent materials, which is expected to solve the problem of heavy metal ion adsorption in sewage. In this paper, esterified tobacco straw based hydrogels (ETS-PAA) were synthesized from waste tobacco straw biomass. The structure and thermal stability of these hydrogels were characterized by FTIR, SEM, EDS, XPS and TG. The adsorption of metal ions by the hydrogel was measured by ICP-MS. The effects of initial ion concentration, adsorption time, pH, and temperature on the heavy metal adsorption were investigated. The results showed that ETS-PAA possessed more pores, which led to a better adsorption capacity. The maximum adsorption amounts of Pb²⁺, Cu²⁺ and Cd²⁺ were 2.41 mmol·g^-1, 1.93 mmol·g^-1 and 1.77 mmol·g^-1, respectively. Finally, the adsorption mechanism and kinetics were analyzed. The adsorption was mainly accomplished by ion exchange of -COOK on the monomer chain with heavy metal ions, coordination of -OH and -CONH with heavy metal ions and interaction of ester bond, -COOH with heavy metal ions. The adsorption process was in accordance with the pseudo-second-order kinetic model and Freundlich model. The adsorption process belonged to multilayer chemisorption. This work shows that ETS-PAA was a promising material for the removal of heavy metal pollutants from aqueous solution.

Combination mechanism of the ternary composite based on Fe3O4-chitosan-graphene oxide prepared by solvothermal method

Magnetic nanohybrid combining chitosan and graphene have demonstrated promising application in environmental remediation. Herein, ternary composite MCG based on Fe₃O₄, chitosan (CS) and graphene oxide (GO) was facilely prepared via solvothermal method. The as prepared composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), Raman, Brunauer/Emmett/Teller-Barret/Joyner/Halenda (BET-BJH) and thermo gravimetric-differential thermal analysis (TG-DTA). The combination mechanism of MCG was unveiled via employing the hard-soft acid-base (HSAB) theory and spectroscopic investigations including X-ray photoelectron spectroscopy (XPS), Ultraviolet-visible (UV-Vis) and fluorescent emission spectra. Particularly, combination mechanism of MCG was elucidated by the probable site to site interaction of the couplet components in MCG, as follows. (1) CS-Fe₃O₄. The primary interaction is N(NH₂)-Fe(III), electron donates from N to Fe, transforming one half of the amino groups of chitosan into positive N⁺. (2) GO-CS. Amidation reaction is the primary interaction form, converting the other half of the amino groups of chitosan into -C(O)NH-. (3) GO-Fe₃O₄. Dominant interactions are those of epoxy, hydroxyl and aromatic ring with Fe(III). Moreover, MCG exhibits fair adsorption performance on divalent heavy metals in six consecutive cycles. These explorations may shed light on the design of efficient adsorbent based on Fe₃O₄-chitosan-graphene architecture.

Adsorption of heavy metal onto biomass-derived activated carbon: review

Due to the rapid development of the social economy and the massive increase in population, human beings continue to undertake processing, and commercial manufacturing activities of heavy metals, which has caused serious damage to the environment and human health. Heavy metals lead to serious environmental problems such as soil contamination and water pollution. Human health and the living environment are closely affected by the handling of heavy metals. Researchers must find several simple, economical and practical methods to adsorb heavy metals. Adsorption technology has been recognized as an efficient and economic strategy, exhibiting the advantages of recovering and reusing adsorbents. Biomass-derived activated carbon adsorbents offer large adjustable specific surface area, hierarchically porous structure, strong adsorption capacity, and excellent high economic applicability. This paper focuses on reviewing the preparation methods of biomass-derived activated carbon in the past five years. The application of representative biomass-derived activated carbon in the adsorption of heavy metals preferentially was described to optimize the critical parameters of the activation type of samples and process conditions. The key factors of the adsorbent, the physicochemical properties of the heavy metals, and the adsorption conditions affecting the adsorption of heavy metals are highlighted. In addition, the challenges faced by biomass-derived activated carbon are also discussed.

Reduction of Ultrafiltration Membrane Fouling by the Pretreatment Removal of Emerging Pollutants: A Review

Ultrafiltration (UF) processes exhibit high removal efficiencies for suspended solids and organic macromolecules, while UF membrane fouling is the biggest obstacle affecting the wide application of UF technology. To solve this problem, various pretreatment measures, including coagulation, adsorption, and advanced oxidation, for application prior to UF processes have been proposed and applied in actual water treatment processes. Previously, researchers mainly focused on the contribution of natural macromolecular pollutants to UF membrane fouling, while the mechanisms of the influence of emerging pollutants (EPs) in UF processes (such as antibiotics, microplastics, antibiotic resistance genes, etc.) on membrane fouling still need to be determined. This review introduces the removal efficiency and separation mechanism for EPs for pretreatments combined with UF membrane separation technology and evaluates the degree of membrane fouling based on the UF membrane's materials/pores and the structural characteristics of the cake layer. This paper shows that the current membrane separation process should be actively developed with the aim of overcoming specific problems in order to meet the technical requirements for the efficient separation of EPs.

Graphene Synthesis Techniques and Environmental Applications

Graphene is fundamentally a two-dimensional material with extraordinary optical, thermal, mechanical, and electrical characteristics. It has a versatile surface chemistry and large surface area. It is a carbon nanomaterial, which comprises sp² hybridized carbon atoms placed in a hexagonal lattice with one-atom thickness, giving it a two-dimensional structure. A large number of synthesis techniques including epitaxial growth, liquid phase exfoliation, electrochemical exfoliation, mechanical exfoliation, and chemical vapor deposition are used for the synthesis of graphene. Graphene prepared using different techniques can have a number of benefits and deficiencies depending on its application. This study provides a summary of graphene preparation techniques and critically assesses the use of graphene, its derivates, and composites in environmental applications. These applications include the use of graphene as membrane material for the detoxication and purification of water, active material for gas sensing, heavy metal ions detection, and CO₂ conversion. Furthermore, a trend analysis of both synthesis techniques and environmental applications of graphene has been performed by extracting and analyzing Scopus data from the past ten years. Finally, conclusions and outlook are provided to address the residual challenges related to the synthesis of the material and its use for environmental applications.

Application of Water Hyacinth Biomass (Eichhornia crassipes) as an Adsorbent for Methylene Blue Dye from Aqueous Medium: Kinetic and Isothermal Study

Water pollution has generated the need to develop technologies to remove industrial pollutants. Adsorption has been recognized as one of the most effective techniques for effluent remediation. In this study, parts (stem and leaves) of a problematic aquatic weed, the water hyacinth (Eichhornia crassipes), were separated to produce a bioadsorbent. The objective was to evaluate the adsorption of a cationic dye, methylene blue (MB), in an aqueous solution of the biomass from different parts of the water hyacinth (Eichhornia crassipes) plants. The materials were characterized through techniques of infrared spectroscopy, scanning electron microscopy, X-ray diffractometry, and thermogravimetric analysis, before and after the material adsorption. Water hyacinth biomasses presented adsorption capacity above 89%, and the kinetics was faster for stem biomass. The kinetic study found that the adsorption process is better described by the pseudo-second-order model, and the adjustments of the isotherm experimental data indicated that both materials are favorable for adsorption. Therefore, water hyacinth bioadsorbent represents a renewable resource with potential for effluent treatment.