Enhanced removal of heavy metals and metalloids by constructed wetlands: A review of approaches and mechanisms

Non-phytoremediation and phytoremediation technologies of integrated remediation for water and soil heavy metal pollution: A comprehensive review

Since the 1980s, there has been increasing concern over heavy metal pollution remediation. However, most research focused on the individual remediation technologies for heavy metal pollutants in either soil or water. Considering the potential migration of these pollutants, it is necessary to explore effective integrated remediation technologies for soil and water heavy metals. This review thoroughly examines non-phytoremediation technologies likes physical, chemical, and microbial remediation, as well as green remediation approaches involving terrestrial and aquatic phytoremediation. Non-phytoremediation technologies suffer from disadvantages like high costs, secondary pollution risks, and susceptibility to environmental factors. Conversely, phytoremediation technologies have gained significant attention due to their sustainable and environmentally friendly nature. Enhancements through chelating agents, biochar, microorganisms, and genetic engineering have demonstrated improved phytoremediation remediation efficiency. However, it is essential to address the environmental and ecological risks that may arise from the prolonged utilization of these materials and technologies. Lastly, this paper presents an overview of integrated remediation approaches for addressing heavy metal contamination in groundwater-soil-surface water systems and discusses the reasons for the research gaps and future directions. This paper offers valuable insights for comprehensive solutions to heavy metal pollution in water and soil, promoting integrated remediation and sustainable development.

Distribution and removal pathways of heavy metals during the operation of sludge treatment wetlands

ABSTRACTThe distribution and removal pathways of heavy metals within different sludge treatment wetlands (STWs) during different running periods in Northeast China have not been well studied. In this study, we examined three STWs, i.e. an STW with aeration tubes only (unit 1; U1), an STW with reeds and aeration tubes (unit 2; U2), and an STW with reeds only (unit 3; U3). The results showed that the levels of Cu as well as Zn accumulated faster within STW residual sludge, whereas the levels of Cd, Cr, Ni, and Pb accumulated more slowly and decreased slightly over time. The removal rates of heavy metals from the influent sludge by STWs ranged from 64.5% (Cr) to 92.2% (Zn). Reeds removed heavy metals from the STWs by direct absorption, and Zn was highly enriched in the reeds. The presence of reeds also promoted the spreading of heavy metals to the substrate layer and improved the removal of heavy metals in STWs. The mass of each heavy metal accumulated within the residual sludge of U2 and U3 was lower than that of U1, indicating that reeds could facilitate the removal of heavy metals. The STWs removed heavy metal mainly by substrate adsorption, and the mass percentage of heavy metals accumulated in the substrate ranged from 35.8 to 63.6%.

Potential of biochar and humic substances for phytoremediation of trace metals in oil sands process affected water

Oil sands process affected water (OSPW) is produced during bitumen extraction and typically contains high concentrations of trace metals. Constructed wetlands have emerged as a cost effective and green technology for the treatment of metals in wastewaters. Whether the addition of amendments to constructed wetlands can improve metal removal efficiency is unknown. We investigated the synergistic effects of carbon based amendments and wetland plant species in removal of arsenic, cadmium, cobalt, chromium, copper, nickel, and selenium from OSPW. Three native wetland species (Carex aquatilis, Juncus balticus, Scirpus validus) and two amendments (canola straw biochar, nano humus) were investigated in constructed wetland mesocosms over 60 days. Amendment effect on metal removal efficiency was not significant, while plant species effect was. Phytoremediation resulted in removal efficiencies of 78.61-96.31 % for arsenic, cadmium, and cobalt. Carex aquatilis had the highest removal efficiencies for all metals. Amendments alone performed well in removing some metals and were comparable to phytoremediation for cadmium, cobalt, copper, and nickel. Metals were primarily distributed in roots with negligible translocation to shoots. Our work provides insights into the role of plants and amendments during metal remediation and their complex interactions in constructed treatment wetlands.

Optimization of hydrochar synthesis conditions for enhanced Cd(II) and Pb(II) adsorption in mono and multimetallic systems

The characterisation of hydrochars derived from Sargassum biomass collected along the Mexican Caribbean coast reveals their favourable morphology and chemical composition for incorporating metal ions, including Cd(II) and Pb(II). Among the synthesized materials, HCS-3, produced at 180 °C with a 2 h residence time, exhibited superior yield, specific area, carbon content, and capacity for removing Cd(II) and Pb(II). Adsorption equilibrium studies demonstrate the presence of adsorption processes during Cd(II) and Pb(II) retention on HCS-3, with adsorption capacities slightly exceeding 140 and 340 mg g⁻1, respectively. Notably, HCS-3 shows a greater affinity for Pb(II) over Cd(II) when both elements are present concurrently. The physicochemical analysis through FTIR spectroscopy, functional group analysis, point of zero charge determination, SEM/EDS, and other techniques evidenced that HCS-3 possesses favourable characteristics to serve as a heavy metal adsorbent. These findings underscore the efficacy of hydrochars from Sargassum biomass in removing heavy metals, suggesting their potential as superior adsorbents compared to traditional or novel materials, and advising its possible versatility for other pollutants. Utilizing these hydrochars could mitigate the economic and environmental impact of Sargassum biomass by repurposing it for valuable applications.

Hybrid constructed wetlands and filamentous fungi for treatment of mixed sewage and industrial effluents

Developing countries face multifaceted problems of water pollution and futile measures to combat water pollution. This study was conducted to explore the potential application of sustainable nature-based solutions, hybrid constructed wetlands, and the application of filamentous fungi to treat polluted river water that receives sewage and industrial wastewater. A pilot-scale hybrid constructed wetland design comprising two types of floating plants in distinct tanks along with a floating wetland and a free-water surface wetland connected in series was commissioned and tested. The system successfully removed organic pollution (BOD 94% and COD 90%), nutrients (NH4-N and NO3-N 67% and PO4-P 81%), and heavy metals (Cr 75%, Ni 56%, and Fe 79%) in 40 h and showed a high buffering capacity to cope with the varying pollutant loads. Metagenomics analysis of treated and untreated samples of river water revealed a diversified spatial bacterial community with ~ 25% sequences related to sulfur-metabolizing bacteria, genus Sulfuricurvum. The application of an immobilized strain of A. niger as a mycoremediation technique was also tested. It successfully removed pollutants in the combined sewage and industrial wastewater present in river water: COD (96%), TSS (97%), NH4-N (65%), NO3-N (67%), and PO4-P (78%). This study demonstrated that hybrid constructed wetlands and mycoremediation can be used as sustainable wastewater treatment options in the local context and also in developing countries where most of the conventional wastewater treatment plants do not operate.

An insight on the plausible biological and non-biological detoxification of heavy metals in tannery waste: A comprehensive review

A key challenge for the tannery industries is the volume of tannery waste water (TWW) generated during the processing of leather, releasing various forms of toxic heavy metals resulting in uncontrolled discharge of tannery waste (TW) into the environment leading to pollution. The pollutants in TW includes heavy metals such as chromium (Cr), cadmium (Cd), lead (Pb) etc, when discharged above the permissible limit causes ill effects on humans. Therefore, several researchers have reported the application of biological and non-biological methods for the removal of pollutants in TW. This review provides insights on the global scenario of tannery industries and the harmful effects of heavy metal generated by tannery industry on micro and macroorganisms of the various ecological niches. It also provides information on the process, advantages and disadvantages of non-biological methods such as electrochemical oxidation, advanced oxidation processes, photon assisted catalytic remediation, adsorption and membrane technology. The various biological methods emphasised includes strategies such as constructed wetland, vermitechnology, phytoremediation, bioaugmentation, quorum sensing and biofilm in the remediation of heavy metals from tannery wastewater (TWW) with special emphasize on chromium.

A review of passive acid mine drainage treatment by PRB and LPB: From design, testing, to construction

An extensive volume of acid mine drainage (AMD) generated throughout the mining process has been widely regarded as one of the most catastrophic environmental problems. Surface water and groundwater impacted by pollution exhibit extreme low pH values and elevated sulfate and metal/metalloid concentrations, posing a serious threat to the production efficiency of enterprises, domestic water safety, and the ecological health of the basin. Over the recent years, a plethora of techniques has been developed to address the issue of AMD, encompassing nanofiltration membranes, lime neutralization, and carrier-microencapsulation. Nonetheless, these approaches often come with substantial financial implications and exhibit restricted long-term sustainability. Among the array of choices, the permeable reactive barrier (PRB) system emerges as a noteworthy passive remediation method for AMD. Distinguished by its modest construction expenses and enduring stability, this approach proves particularly well-suited for addressing the environmental challenges posed by abandoned mines. This study undertook a comprehensive evaluation of the PRB systems utilized in the remediation of AMD. Furthermore, it introduced the concept of low permeability barrier, derived from the realm of site-contaminated groundwater management. The strategies pertaining to the selection of materials, the physicochemical aspects influencing long-term efficacy, the intricacies of design and construction, as well as the challenges and prospects inherent in barrier technology, are elaborated upon in this discourse.

Removal of metals and emergent contaminants from liquid digestates in constructed wetlands for agricultural reuse

Given the increasing pressure on water bodies, it is imperative to explore sustainable methodologies for wastewater treatment and reuse. The simultaneous presence of multiples contaminants in complex wastewater, such as the liquid effluents from biogas plants, can compromise biological treatment effectiveness for reclaiming water. Vertical subsurface flow constructed wetlands were established as low-cost decentralized wastewater treatment technologies to treat the liquid fraction of digestate from municipal organic waste with metals, antibiotics, and antibiotic resistance genes, to allow its reuse in irrigation. Twelve lab-scale planted constructed wetlands were assembled with gravel, light expanded clay aggregate and sand, testing four different treating conditions (liquid digestate spiked with oxytetracycline, sulfadiazine, or ofloxacin, at 100 μg/ L, or without dosing) during 3 months. Physicochemical parameters (pH, chemical oxygen demand (COD), nutrients, metals, and antibiotics), the microbial communities dynamics (through 16S high-throughput sequencing) and antibiotic resistance genes removal (qPCR) were monitored in influents and effluents. Systems removed 85.8%-96.9% of organic matter (as COD), over 98.1% of ammonium and phosphate ions, and 69.3%-99.4% of nitrate and nitrite ions, with no significant differences between the presence or absence of antibiotics. Removal of Fe, Mn, Zn, Cu, Pb and Cr exceeded 82% in all treatment cycles. The treatment also removed oxytetracycline, sulfadiazine and ofloxacin over 99%, and decreased intl1, tetA, tetW, sul1 and qnrS gene copies. Nonetheless, after 3 months of ofloxacin dosing, qnrS gene started being detected. Removal processes relied on high HRT (14 days) and various mechanisms including sorption, biodegradation, and precipitation. Microbial community diversity in liquid digestate changed significantly after treatment in constructed wetlands with a decrease in the initial Firmicutes dominance, but with no clear effect of antibiotics on the microbial community structure. Removals above 85% and 94% were observed for Streptococcus and Clostridium, respectively. Results suggest that vertical subsurface flow constructed wetlands were a suitable technology for treating the liquid digestate to reuse it in irrigation agricultural systems, contributing to the circular bioeconomy concept. However, a more profound understanding of effective wastewater treatment strategies is needed to avoid antibiotic resistance genes dissemination.

Adsorption properties of Pb(II) and Cd(II) in acid mine drainage by oyster shell loaded lignite composite in different morphologies

A new idea to alleviate environmental pollution is the development of low-cost adsorbents using natural minerals and fishery wastes to treat high concentrations of heavy metal pollutants in acid mine drainage (AMD). Adsorbent morphology, adsorptive and regenerative capacity, and application potential are limiting factors for their large-scale use. Oyster shells capable of releasing alkalinity were loaded on the surface of lignite to develop two composite adsorbents with different morphologies (powdery and globular) for the treatment of AMD containing Pb(II) and Cd(II). The results show that the ability of the adsorbent to treat AMD is closely related to its morphologies. The pseudo-second-order kinetic model and the Langmuir model are suitable to describe the adsorption process of OS-M(P), and the maximum adsorption saturation capacities of Pb(II) and Cd(II) are 332.6219 mg/g and 318.9854 mg/g, respectively. The pseudo-second-order kinetic model and the Freundlich model are suitable to describe the adsorption process of OS-M(G). A synergistic result of electrostatic adsorption, neutralization precipitation, ion exchange and complex reaction is achieved in the removal of Pb(II) and Cd(II) by two morphologies of adsorbents. The regeneration times (5 times) and recovery rate (75.75%) of OS-M(G) are higher than those of OS-M(P) (3 times) and recovery rate (20%). The ability of OS-M(G) to treat actual AMD wastewater is still better than that of OS-M(P). OS-M(G) can be used as a promising environmentally friendly adsorbent for the long-term remediation of AMD. This study provides a comprehensive picture of resource management and reuse opportunities for natural mineral and fishery wastes.

Bioenergy-producing two-stage septic tank and floating wetland for onsite wastewater treatment: Circuit connection and external aeration

This study designed a two-stage, electrode-integrated septic tank-floating wetland system and assessed their pollutant removal performances under variable operational conditions. The two-stage system achieved mean organic, nitrogen, phosphorus, and coliform removal percentages of 99, 78, 99, and 97%, respectively, throughout the experimental run. The mean metals (chromium, cadmium, nickel, copper, zinc, lead, iron, and manganese) removal percentages ranged between 81 and 98%. Accumulated sludge, filler media, and the hanging root mass contributed to pollutant removals by supporting physicochemical and biological pathways. The mean effluent organic concentration and coliform number across the two-stage system were 20 mg/L and 1682 CFU/100 mL, respectively, during the closed-circuit protocol, which was beneath the open-circuit-based performance profiles, i.e., 32 mg/L and 2860 CFU/100 mL, respectively. Effluent organic, nitrogen, phosphorus, metals, and coliform number ranges across the two-stage system were 9-17 mg/L, 13-24 mg/L, 1-1.5 mg/L, 0.001-0.2 mg/L, and 1410-2270 CFU/100 mL, respectively during intermittent and continuous aeration periods. The air supply rate differences influenced pollutant removal depending on the associated removal mechanisms. The non-aeration phase produced higher effluent pollutant concentrations than the aeration periods-based profiles. The overall mean power density production of the septic tank ranged between 107 and 596 mW/m3; 110 and 355 mW/m3 with the floating wetland. The bioenergy production capacity of the septic tank was positively correlated to external air supply rates. This study demonstrates the potential application of the novel bioenergy-producing septic tank-floating wetland system for wastewater treatment in decentralized areas.

A pilot-scale assessment of five common weeds in the sustainable treatment of sewage utilizing SHEFROL®, with prospects of a closed-loop biorefinery

Relative efficacy of five common weeds-of the kind that are either rooted in soil or which freely float over water-was assessed in rapid, effective and sustainable treatment of sewage at pilot plant scale in the recently developed and patented SHEFROL® bioreactors. The plants were utilized in a unit of capacity 12,000 liters/day (LPD) which, after two years of use, was enlarged to handle 40,000 LPD of sewage. It was then further expanded after an year to treat 57,000 LPD. All the five weeds, of which none has previously been tested in a pilot-scale SHEFROL, were able to foster highly efficient primary treatment (in terms of suspended and total solids) and secondary treatment (in terms of BOD and COD) to levels exceeding 85% in most cases. Additionally, the weeds also helped in achieving significant tertiary treatment. At different hydraulic retention times, and at steady state, the five weeds achieved treatment of BOD, COD, suspended solids, nitrogen, phosphorous, copper, nickel, zinc, and manganese in the ranges, 80-95, 79-91, 82-95, 61-71, 51-73, 37-43, 30-38, 39-47, and 27-35%, respectively. It all occurred in a single process step and without the use of any machine or chemical. This made the system not only simple and inexpensive to install but also to maintain. Over continuous long-term operation for four years, the system was seen to be very robust as it was able to handle wide variations in the volumes and characteristics of sewage, as well as absorb shock loads without compromising the reactor performance. The sustainability of the system can be further enhanced by upgrading it to a circular biorefinery. Energy sources in the form of volatile fatty acids (VFAs) can be extracted from the weeds removed from SHEFROL and then the weeds can be converted into organic fertilizer using high-rate vermireactors recently developed by the authors.

Zinc and nano zinc mediated alleviation of heavy metals and metalloids in plants: an overview

Heavy metals and metalloids (HMs) contamination in the environment has heightened recently due to increasing global concern for food safety and human livability. Zinc (Zn2+ ) is an important nutrient required for the normal development of plants. It is an essential cofactor for the vital enzymes involved in various biological mechanisms of plants. Interestingly, Zn2+ has an additional role in the detoxification of HMs in plants due to its unique biochemical-mediating role in several soil and plant processes. During any exposure to high levels of HMs, the application of Zn2+ would confer greater plant resilience by decreasing oxidative stress, maintaining uptake of nutrients, photosynthesis productivity and optimising osmolytes concentration. Zn2+ also has an important role in ameliorating HMs toxicity by regulating metal uptake through the expression of certain metal transporter genes, targeted chelation and translocation from roots to shoots. This review examined the vital roles of Zn2+ and nano Zn in plants and described their involvement in alleviating HMs toxicity in plants. Moving forward, a broad understanding of uptake, transport, signalling and tolerance mechanisms of Zn2+ /zinc and its nanoparticles in alleviating HMs toxicity of plants will be the first step towards a wider incorporation of Zn2+ into agricultural practices.

Removal of chloramphenicol and resistance gene changes in electric-integrated vertical flow constructed wetlands

The performance of an electric-integrated vertical flow constructed wetland (E-VFCW) for chloramphenicol (CAP) removal, changes in microbial community structure, and the fate of antibiotic resistance genes (ARGs) were evaluated. CAP removal in the E-VFCW system was 92.73% ± 0.78% (planted) and 90.80% ± 0.61% (unplanted), both were higher than the control system which was 68.17% ± 1.27%. The contribution of anaerobic cathodic chambers in CAP removal was higher than the aerobic anodic chambers. Plant physiochemical indicators in the reactor revealed electrical stimulation increased oxidase activity. Electrical stimulation enhanced the enrichment of ARGs in the electrode layer of the E-VFCW system (except floR). Plant ARGs and intI1 levels were higher in the E-VFCW than in the control system, suggesting electrical stimulation induces plants to absorb ARGs, reducing ARGs in the wetland. The distribution of intI1 and sul1 genes in plants suggests that horizontal transfer may be the main mechanism dispersing ARGs in plants. High throughput sequencing analysis revealed electrical stimulation selectively enriched CAP degrading functional bacteria (Geobacter and Trichlorobacter). Quantitative correlation analysis between bacterial communities and ARGs confirmed the abundance of ARGs relates to the distribution of potential hosts and mobile genetic elements (intI1). E-VFCW is effective in treating antibiotic wastewater, however ARGs potentially accumulate.

Innovative Membrane Technologies for the Treatment of Wastewater Polluted with Heavy Metals: Perspective of the Potential of Electrodialysis, Membrane Distillation, and Forward Osmosis from a Bibliometric Analysis

A bibliometric analysis, using the Scopus database as a source, was carried out in order to study the scientific documents published up to 2021 regarding the use of electrodialysis, membrane distillation, and forward osmosis for the removal of heavy metals from wastewater. A total of 362 documents that fulfilled the search criteria were found, and the results from the corresponding analysis revealed that the number of documents greatly increased after the year 2010, although the first document was published in 1956. The exponential evolution of the scientific production related to these innovative membrane technologies confirmed an increasing interest from the scientific community. The most prolific country was Denmark, which contributed 19.3% of the published documents, followed by the two main current scientific superpowers: China and the USA (with 17.4% and 7.5% contributions, respectively). Environmental Science was the most common subject (55.0% of contributions), followed by Chemical Engineering (37.3% of contributions) and Chemistry (36.5% of contribution). The prevalence of electrodialysis over the other two technologies was clear in terms of relative frequency of the keywords. An analysis of the main hot topics identified the main advantages and drawbacks of each technology, and revealed that examples of their successful implementation beyond the lab scale are still scarce. Therefore, complete techno-economic evaluation of the treatment of wastewater polluted with heavy metals via these innovative membrane technologies must be encouraged.

Insights into the enhanced effect of biochar on cadmium removal in vertical flow constructed wetlands

Biochar has been increasingly applied in constructed wetlands (CWs) to remediate heavy metal (HM)-polluted water. Nevertheless, only few studies have elucidated the enhanced mechanism and potential synergies related to the HM removal from biochar-based CWs (BC-CWs) for HMs removal. This study used cadmium (Cd) as the target HM and added biochar into CWs to monitor physicochemical parameters, plant' physiological responses, substrate accumulation, and microbial metabolites and taxa. In comparison with the biochar-free CW (as CWC), a maximum Cd²⁺ removal of 99.7% was achieved in the BC-CWs, associated with stable physicochemical parameters. Biochar preferentially adsorbed the available Cd²⁺ and significantly accumulated Fe/Mn oxides-bond and the exchangeable Cd fraction. Moreover, biochar alleviated the lipid peroxidation (decreased by 36.4%) of plants, resulting in improved growth. In addition, extracellular polymeric substances were increased by 376.9-396.8 mg/L in BC-CWs than compared to CWC, and N and C cycling was enhanced through interspecific positive connectivity. In summary, this study explored comprehensively the performance and mechanism of BC-CWs in the treatment of Cd²⁺-polluted water, suggesting a promising approach to promote the plant-microbe-substrate synergies under HM toxicity.

Recent advances in constructed wetlands methane reduction: Mechanisms and methods

Constructed wetlands (CWs) are artificial systems that use natural processes to treat wastewater containing organic pollutants. This approach has been widely applied in both developing and developed countries worldwide, providing a cost-effective method for industrial wastewater treatment and the improvement of environmental water quality. However, due to the large organic carbon inputs, CWs is produced in varying amounts of CH₄ and have the potential to become an important contributor to global climate change. Subsequently, research on the mitigation of CH₄ emissions by CWs is key to achieving sustainable, low-carbon dependency wastewater treatment systems. This review evaluates the current research on CH₄ emissions from CWs through bibliometric analysis, summarizing the reported mechanisms of CH₄ generation, transfer and oxidation in CWs. Furthermore, the important environmental factors driving CH₄ generation in CW systems are summarized, including: temperature, water table position, oxidation reduction potential, and the effects of CW characteristics such as wetland type, plant species composition, substrate type, CW-coupled microbial fuel cell, oxygen supply, available carbon source, and salinity. This review provides guidance and novel perspectives for sustainable and effective CW management, as well as for future studies on CH₄ reduction in CWs.

An inexpensive phytoremediation system for treating 50,000 L/day of sewage

The paper describes the setting up and long-term continuous operation of the first real-life, pilot scale, sewage treatment plant based on the recently patented phytoremediation technology, trademarked as SHEFROL^®. The unit was about three times cheaper to install, operate and maintain than the least expensive of the other wetland-based technologies presently in vogue. Its semi-permanent version is 30 times cheaper. Monitoring of flow rates and levels of treatment intermittently over a 3 year course of continuous operation indicated the constancy and robustness of the reactor in treating total solids, suspended solids, chemical oxygen demand, biological oxygen demand, total Kjeldahl nitrogen, and soluble phosphorous to the average extents of 94, 84, 79, 70, 62 and 28% respectively. Earlier experience with bench-scale SHEFROL^® units has indicated that removal of metals like Cu, Ni, Co, Zn, and Mn also takes place to the extent of 25-45% in these systems. These primary, secondary, and tertiary treatments occurred in a single unit process with no necessity of any pumping, aeration, or recycling. Models based on artificial intelligence were developed which enable forecasting the reactor performance in terms of secondary and tertiary treatment, respectively.

Advances in microbial electrochemistry-enhanced constructed wetlands

Constructed wetland (CW) is an effective ecological technology to treat water pollution and has the significant advantages of high impact resistance, simple construction process, and low maintenance cost. However, under extreme conditions such as low temperature, high salt concentration, and multiple types of pollutants, some bottlenecks exist, including the difficulty in improving operating efficiency and the low pollutant removal rate. Microbial electrochemical technology is an emerging clean energy technology and has the similar structure and pollutant removal mechanism to CW. Microbial electrochemistry combined with CW can improve the overall removal effect of pollutants in wetlands. This review summarizes characterization methods of microbial electrochemistry-enhanced constructed wetland systems, construction methods of different composite systems, mechanisms of single and composite systems, and removal effects of composite systems on different pollutants in water bodies. Based on the shortcomings of existing studies, the potential breakthroughs in microbial electrochemistry-enhanced constructed wetlands are proposed for developing the optimization solution of constructed wetlands.

Wastewater treatment using bamboos in constructed wetlands: experiences and future perspectives

Wastewater treatment using constructed wetlands (CWs) based on natural wetlands constitute a viable alternative with excellent cost and benefit, presenting themselves as efficient technologies in the secondary and tertiary treatment of wastewaters with low implementation, operation, and maintenance costs. The present study aims to evaluate the use of bamboo species, as an alternative to macrophytes, frequently used in CWs, through bibliometric analysis, besides to a review based on case studies. The maps generated by the VOSviewer software and by the analyses of the Web of Science and Scopus databases allowed for a review of typical concepts of CWs, in addition to revealing potential benefits of using bamboos in CWs, such as their hyperaccumulation capacity and bioproduct generation. Other promising aspects were identified, for example the use of bamboo charcoal as a substrate used in subsurface wetlands and the application of ornamental bamboo species for landscape improvements, among other observations. The efficiencies found in six case studies showed values between 89-99.7%, 47.6-99.7%, 58.3-99.9%, and 85.5-99.8% for BOD₅, COD, total nitrogen (TN), and total phosphorus (TP), respectively. Despite the promising results, the lack of studies using bamboos in CWs for the treatment of wastewaters limits an assertive statement about the use of this technology, requiring further research, focusing on the morphological functions of bamboos in this treatment with landscape integration and resources recovery.