Cost-effective photoelectrocatalytic treatment of dyes in a batch reactor equipped with solar cells

Revealing the influences of functional groups in azo dyes on the degradation efficiency and power output in solar photocatalytic fuel cell

In this study, the degradation efficiency and electricity generation of the azo dyes affected by the functional groups and molecular structure in a solar photocatalytic fuel cell (PFC) system were investigated and discussed in detail. Four different azo dyes such as, Acid Orange 7 (AO7), Acid Red 18 (AR18), Reactive Black 5 (RB5), Reactive Red 120 (RR120) with different molecular structure were evaluated. The degradation efficiency of AO7, AR18, RB5 and RR120 achieved 5.6 ± 0.3%, 11.1 ± 0.6%, 41.9 ± 0.9% and 52.1 ± 1.3%, respectively, after 6 h irradiated under solar light. In addition, the maximum power density, P_max for AO7, AR18, RB5 and RR120 was 0.0269 ± 0.01, 0.111 ± 0.03, 1.665 ± 0.67 and 4.806 ± 1.79 mW cm^-2, respectively. Meanwhile, the concentration of COD for AO7, AR18, RB5 and RR120 reduced to 16 ± 0.1, 10 ± 0.3, 7 ± 0.6 and 3 ± 0.9 mg L^-1, respectively. The concentration ratio of benzene / naphthalene, benzene / azo bond and naphthalene / azo bond, respectively, was analyzed to investigate the impact of the functional groups over photodegradation of the azo dyes in PFC. Electron releasing groups (-OH and -NH₂) and electron withdrawing groups (-SO₃Na) which attached to the naphthalene or benzene ring also played a pivotal role in the degradation mechanism.

Degradation of chloramphenicol using Ti-Sb/attapulgite ceramsite particle electrodes

Ti-Sb/attapulgite ceramsite particle electrodes were prepared for the efficient degradation of chloramphenicol (CAP) in wastewater. To observe the surface morphology and structural characteristics of the Ti-Sb/attapulgite ceramsite particle electrodes, Fourier transform infrared spectroscopy, X-ray fluorescence, scanning electron microscopy, and X-ray diffraction were used for characterization. Parameters affecting the degradation efficiency and the energy consumption of the Ti-Sb/attapulgite ceramsite particle electrodes, such as current density, electrode distance, initial pH, conductivity, air flow, and packing ratio, were examined. Results showed that the optimal conditions were 20 mA/cm² current intensity, 3 cm electrode distance, 5,000 μS/cm conductivity, 2.0 L/min air flow, 50.0% packing ratio, and initial pH 1. The removal efficiency of chloramphenicol was 73.7% under the optimal conditions, and the energy consumption was 191.3 (kW h)/kg CAP. PRACTITIONER POINTS: Attapulgite ceramsite with good physical performance was prepared. The removal efficiencies for CAP in water by Ti-Sb/attapulgite ceramsite particle electrodes were studied. CAP was effectively removed by 3-D electrode system. CAP removal was significantly influenced by operational parameters. Three-dimensional electrode system shows good degradation ability.

Recent advances in heterogeneous photocatalytic decolorization of synthetic dyes

During the process and operation of the dyes, the wastes produced were commonly found to contain organic and inorganic impurities leading to risks in the ecosystem and biodiversity with the resultant impact on the environment. Improper effluent disposal in aqueous ecosystems leads to reduction of sunlight penetration which in turn diminishes photosynthetic activity, resulting in acute toxic effects on the aquatic flora/fauna and dissolved oxygen concentration. Recently, photodegradation of various synthetic dyes has been studied in terms of their absorbance and the reduction of oxygen content by changes in the concentration of the dye. The advantages that make photocatalytic techniques superior to traditional methods are the ability to remove contaminates in the range of ppb, no generation of polycyclic compounds, higher speed, and lower cost. Semiconductor metal oxides, typically TiO₂, ZnO, SnO, NiO, Cu₂O, Fe₃O₄, and also CdS have been utilized as photocatalyst for their nontoxic nature, high photosensitivity, wide band gap and high stability. Various process parameters like photocatalyst dose, pH and initial dye concentrations have been varied and highlighted. Research focused on surface modification of semiconductors and mixed oxide semiconductors by doping them with noble metals (Pt, Pd, Au, and Ag) and organic matter (C, N, Cl, and F) showed enhanced dye degradation compared to corresponding native semiconductors. This paper reviews recent advances in heterogeneous photocatalytic decolorization for the removal of synthetic dyes from water and wastewater. Thus, the main core highlighted in this paper is the critical selection of semiconductors for photocatalysis based on the chemical, physical, and selective nature of the poisoning dyes.