Enhancement in hydrophilicity of different polymer phase-inversion ultrafiltration membranes by introducing PEG/Al2O3 nanoparticles

Perfluorooctanoic acid-contaminated wastewater treatment by forward osmosis: Performance analysis

Perfluorooctanoic acid (PFOA) is a persistent compound, raising considerable global apprehension due to its resistance to breakdown and detrimental impacts on human health and aquatic environments. Pressure-driven membrane technologies treating PFAS-contaminated water are expensive and prone to fouling. This study presented a parametric investigation of the effectiveness of cellulose triacetate membrane in the forward osmosis (FO) membrane for removing PFOA from an aqueous solution. The study examined the influence of membrane orientation modes, feed pH, draw solution composition and concentration, and PFOA concentration on the performance of FO. The experimental results demonstrated that PFOA rejection was 99 % with MgCl2 and slightly >98 % with NaCl draw solutions due to the mechanism of PFOA binding to the membrane surface through Mg2+ ions. This finding highlights the crucial role of the draw solution's composition in PFOA treatment. Laboratory results revealed that membrane rejection of PFOA was 99 % at neutral and acidic pH levels but decreased to 95 % in an alkaline solution at pH 9. The decrease in membrane rejection is attributed to the dissociation of the membrane's functional groups, consequently causing pore swelling. The results were confirmed by calculating the average pore radius of the CTA membrane, which increased from 27.94 nm at pH 5 to 30.70 nm at pH 9. Also, variations in the PFOA concentration from 5 to 100 mg/L did not significantly impact the membrane rejection, indicating the process's capability to handle a wide range of PFOA concentrations. When seawater was the draw solution, the FO membrane rejected 99 % of PFOA concentrations ranging from 5 mg/L to 100 mg/L. The CTA FO treating PFOA-contaminated wastewater from soil remediation achieved a 90 % recovery rate and water flux recovery of 96.5 % after cleaning with DI water at 40 °C, followed by osmotic backwash. The results suggest the potential of using abundant and cost-effective natural solutions in the FO process, all without evident membrane fouling.

Bead-Containing Superhydrophobic Nanofiber Membrane for Membrane Distillation

This study introduces an innovative approach to enhancing membrane distillation (MD) performance by developing bead-containing superhydrophobic sulfonated polyethersulfone (SPES) nanofibers with S-MWCNTs. By leveraging SPES's inherent hydrophobicity and thermal stability, combined with a nanostructured fibrous configuration, we engineered beads designed to optimize the MD process for water purification applications. Here, oxidized hydrophobic S-MWCNTs were dispersed in a SPES solution at concentrations of 0.5% and 1.0% by weight. These bead membranes are fabricated using a novel electrospinning technique, followed by a post-treatment with the hydrophobic polyfluorinated grafting agent to augment nanofiber membrane surface properties, thereby achieving superhydrophobicity with a water contact angle (WCA) of 145 ± 2° and a higher surface roughness of 512 nm. The enhanced membrane demonstrated a water flux of 87.3 Lm-2 h-1 and achieved nearly 99% salt rejection efficiency at room temperature, using a 3 wt% sodium chloride (NaCl) solution as the feed. The results highlight the potential of superhydrophobic SPES nanofiber beads in revolutionizing MD technology, offering a scalable, efficient, and robust membrane for salt rejection.

Next-Generation Water Treatment: Exploring the Potential of Biopolymer-Based Nanocomposites in Adsorption and Membrane Filtration

This review article focuses on the potential of biopolymer-based nanocomposites incorporating nanoparticles, graphene oxide (GO), carbon nanotubes (CNTs), and nanoclays in adsorption and membrane filtration processes for water treatment. The aim is to explore the effectiveness of these innovative materials in addressing water scarcity and contamination issues. The review highlights the exceptional adsorption capacities and improved membrane performance offered by chitosan, GO, and CNTs, which make them effective in removing heavy metals, organic pollutants, and emerging contaminants from water. It also emphasizes the high surface area and ion exchange capacity of nanoclays, enabling the removal of heavy metals, organic contaminants, and dyes. Integrating magnetic (Fe2O4) adsorbents and membrane filtration technologies is highlighted to enhance adsorption and separation efficiency. The limitations and challenges associated are also discussed. The review concludes by emphasizing the importance of collaboration with industry stakeholders in advancing biopolymer-based nanocomposites for sustainable and comprehensive water treatment solutions.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

Classification of Nanomaterials and the Effect of Graphene Oxide (GO) and Recently Developed Nanoparticles on the Ultrafiltration Membrane and Their Applications: A Review

The emergence of mixed matrix membranes (MMMs) or nanocomposite membranes embedded with inorganic nanoparticles (NPs) has opened up a possibility for developing different polymeric membranes with improved physicochemical properties, mechanical properties and performance for resolving environmental and energy-effective water purification. This paper presents an overview of the effects of different hydrophilic nanomaterials, including mineral nanomaterials (e.g., silicon dioxide (SiO₂) and zeolite), metals oxide (e.g., copper oxide (CuO), zirconium dioxide (ZrO₂), zinc oxide (ZnO), antimony tin oxide (ATO), iron (III) oxide (Fe2O3) and tungsten oxide (WO_X)), two-dimensional transition (e.g., MXene), metal-organic framework (MOFs), covalent organic frameworks (COFs) and carbon-based nanomaterials (such as carbon nanotubes and graphene oxide (GO)). The influence of these nanoparticles on the surface and structural changes in the membrane is thoroughly discussed, in addition to the performance efficiency and antifouling resistance of the developed membranes. Recently, GO has shown a considerable capacity in wastewater treatment. This is due to its nanometer-sized holes, ultrathin layer and light and sturdy nature. Therefore, we discuss the effect of the addition of hydrophilic GO in neat form or hyper with other nanoparticles on the properties of different polymeric membranes. A hybrid composite of various NPs has a distinctive style and high-quality products can be designed to allow membrane technology to grow and develop. Hybrid composite NPs could be used on a large scale in the future due to their superior mechanical qualities. A summary and future prospects are offered based on the current discoveries in the field of mixed matrix membranes. This review presents the current progress of mixed matrix membranes, the challenges that affect membrane performance and recent applications for wastewater treatment systems.

Photocatalytic nanohybrid membranes for highly efficient wastewater treatment: A comprehensive review

Wastewater is inevitably generated from human activities as part of the life cycle chain that potentially damages the environment. The integration of photocatalytic reaction and membrane separation for wastewater treatment has gained great attention in recent studies. However, there are still many technical limitations for its application such as toxic metal release, catalyst deactivation, fouling/biofouling, polymer disintegration, and separation performance decline. Different types, combinations, and modifications of photocatalysts material combined with membranes such as semiconductor metal oxides, binary/ternary hybrid metal oxides, elemental doped semiconductors, and metal-organic frameworks (MOFs) for improving the performance and compatibility are presented and discussed. The strategies of incorporating photocatalysts into membrane matrix for pursuing the most stable membrane integrity, high photocatalytic efficiency, and excellent perm-selectivity performance in the very recent studies were discussed. This review also outlines the performance enhancement of photocatalytic membranes (PMs) in wastewater treatment and its potential for water reclamation. Photocatalysts enhanced membrane separation by inducing anti-fouling and self-cleaning properties as well as antibacterial activity. Based on the reviewed study, PMs are possible to achieve complete removal of emerging contaminants and ∼99% reduction of bacterial colony that leading on the zero liquid discharge (ZLD). However, the intensive exposure of photo-induced radicals potentially damages the polymeric membrane. Therefore, future studies should be focused on fabricating chemically stable host-membrane material. Moreover, the light source and the membrane module design for the practical application by considering the hydrodynamic and cost-efficiency should be a concern for technology diffusion to the industrial-scale application.

A Novel Treatment: Effects of Nano-Sized and Micro-Sized Al2O3 on Steel Surface for the Shear Strength of Epoxy–Steel Single-Lap Joints

Traditional steel surface treatment (e.g., sand blasting, or silane treatment) was regarded as an effective method to improve the bonding strength of steel–epoxy single-lap joints. In the present study, a new steel surface treatment method was developed. With this method, the steel surfaces were treated with suspensions of nano-sized and micro-sized Al2O3 particles in ethanol/water mixture using the dip-coating method. Both Al2O3 particle sizes were previously treated or not treated with silane. Single-lap shear tests of the steel–epoxy bonds were conducted to compare the effects of the treating methods. According to the testing results, the highest increase in the bonding strength (by 51.8%) was found for the steel coated with the suspension of silane treated nano-Al2O3 particles. Scanning electron microscopy (SEM) analysis and energy dispersive spectrometer (EDS) analysis indicates that the nano-Al2O3 particles were clearly attached to the treated steel surfaces. Moreover, the steel surface with the silane-treated nano-Al2O3 particles was found to clearly enhance the contact angle between the steel and epoxy resin. The fracture morphology analysis of the single-lap shear testing specimen shows that the bonding between the steel and adhesive changed from steel–epoxy interfacial failure to cohesive failure when the steel surfaces were treated with the nano-Al2O3 particles suspension. The developed steel surface treatment method with the suspension of nano-particles proves to be effective and reliable in enhancing the bonding strength of the steel-to-epoxy adhesives.

Fabrication and characterization of high-performance forward-osmosis membrane by introducing manganese oxide incited graphene quantum dots

Forward osmosis (FO) is the futuristic membrane desalination technology as it transcends the disadvantages of other pressure-driven techniques. But, there still remain critical challenges like fabrication of highly permeable membrane with ideal structures maintaining high rejection rates that need to be addressed for implementation as a practical technology. In this work, novel thin-film composite (TFC) membranes were fabricated by means of incorporating manganese oxide (MnO₂) incited graphene quantum dots (GQDs) nanocomposite into a cellulose acetate (CA) suspension followed by phase inversion (PI) for enhanced FO performance. The surface morphology and chemical structure of fabricated membranes were studied using various characterization techniques like XRD, FT-IR, SEM-EDS, Mapping, AFM, and TGA. The structural parameters, water flux, reverse salt flux and salt rejection was estimated on the basis of data obtained from four varying initial draw solution concentrations. At high nanocomposites stacking, the hydrophilicity of the casting blend increase, and subsequently, the PI exchange rate additionally increases, which brings about noticeable difference in the surface morphology. The membrane with 0.5 wt% nanocomposite exhibited superior FO separation performance with osmotic water flux of 18.89, 34.49, 41.76 and 42.34 in L.m^-2.h^-1 with variable concentrations of NaCl salt solution (0.25M, 0.5M, 1M, and 2M), respectively. Also, the porosity of the membrane was increased to 47.23% with 96.87% salt rejection. The results indicate that the hydrophilicity of the nanocomposite drives them to the interface among CA and water during PI process leading to solid hydrogen bonding to achieve high water permeability.

Alkyl Silica Hybrid Nanowire Assembly in Improved Superhydrophobic Membranes for RO Filtration

Alkyl silica membranes and wires were synthesized by a sol-gel method, which has the capacity to control the size of the particles or membranes by controlling the reactions. Trimethoxyoctylsilane (C₈TMOS) was used as a chemical surfactant; poly(vinylpyrrolidone) (PVP) as an emulsifier, dissolved in butanol for emulsion; and tetraethylorthosilicate (TEOS) as a precursor and a source of silica. An assembly of silica wires was fabricated on glass and cotton substrates by the dip-coating technique. Porous membranes and silica wires were observed using scanning electron microscopy (SEM) images. The contact angles of all of the samples were in the range of 140-154° as measured by ImageJ software, which confirmed the hydrophobic nature of the samples. The contact angle was increased by increasing the amount of the surfactant. Phase changes of silica wires and membranes were investigated by thermogravimetric analysis. Chemical bonds of the sample were studied using Fourier transform infrared (FTIR) spectroscopy. The band gap of silica nanowires was measured to be 3.8-3.4 eV using the UV-visible spectrum and decreased as compared to that of bulk silica. These silica-based porous membranes with enhanced transport properties can be used in filtration and separation techniques. This fabricated hybrid silica membrane showed ∼96% salt rejection within a permeation flux of 3.04 L/m² h.

Fabrication of Polysulfone-Surface Functionalized Mesoporous Silica Nanocomposite Membranes for Removal of Heavy Metal Ions from Wastewater

Membranes are an efficient way to treat emulsified heavy metal-based wastewater, but they generally come with a trade-off between permeability and selectivity. In this research, the amine and sulphonic groups on the inner and outer surface of mesoporous silica nanoparticles (MSNs) were first modified by a chemical approach. Then, MSNs with amine and sulphonic groups were utilized as new inorganic nanofiller to fabricate mixed matrix polysulfone (PSU) nanocomposite membranes using the classical phase inversion approach. The resultant nanoparticles and membranes were characterized by their physico-chemical characteristics as well as determination of pure water permeability along with cadmium and zinc ion removal. Embedding nanoparticles resulted in a significant rise in the water permeability as a result of changes in the surface properties and porosity of the membrane. Furthermore, the efficiency of developed membranes to remove cadmium and zinc was significantly improved by more than 90% due to the presence of functional groups on nanoparticles. The functionalized-MSNs/PSU nanocomposite membrane has the potential to be an effective industrial effluent removal membrane.

Manufacturing and Characterisation of Polymeric Membranes for Water Treatment and Numerical Investigation of Mechanics of Nanocomposite Membranes

In this study, polyethersulfone (PES) and polyvinylidene fluoride (PVDF) microfiltration membranes containing polyvinylpyrrolidone (PVP) with and without support layers of 130 and 150 μm thickness are manufactured using the phase inversion method and then experimentally characterised. For the characterisation of membranes, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and pore size analysis are performed, the contact angle and water content of membranes are measured and the tensile test is applied to membranes without support layers. Using the results obtained from the tensile tests, the mechanical properties of the halloysite nanotube (HNT) and nano-silicon dioxide (nano SiO₂) reinforced nanocomposite membranes are approximately determined by the Mori–Tanaka homogenisation method without applying any further mechanical tests. Then, plain polymeric and PES and PVDF based nanocomposite membranes are modelled using the finite element method to determine the effect of the geometry of the membrane on the mechanical behaviour for fifteen different geometries. The modelled membranes compared in terms of three different criteria: equivalent stress (von Mises), displacement, and in-plane principal strain. Based on the data obtained from the characterisation part of the study and the numerical analysis, the membrane with the best performance is determined. The most appropriate shape and material for a membrane for water treatment is specified as a 1% HNT doped PVDF based elliptical membrane.

Nanofiltration Composite Membranes Based on KIT-6 and Functionalized KIT-6 Nanoparticles in a Polymeric Matrix with Enhanced Performances

The nanofiltration composite membranes were obtained by incorporation of KIT-6 ordered mesoporous silica, before and after its functionalization with amine groups, into polyphenylene-ether-ether-sulfone (PPEES) matrix. The incorporation of silica nanoparticles into PPEES polymer matrix was evidenced by FTIR and UV–VIS spectroscopy. SEM images of the membranes cross-section and their surface topology, evidenced by AFM, showed a low effect of KIT-6 silica nanoparticles loading and functionalization. The performances of the obtained membranes were appraised in permeation of Chaenomeles japonica fruit extracts and the selective separation of phenolic acids and flavonoids. The obtained results proved that the PPEES with functionalized KIT-6 nanofiltration membrane, we have prepared, is suitable for the polyphenolic compound’s concentration from the natural extracts.

Enhanced performance of porous forward osmosis (FO) membrane in the treatment of oily wastewater containing HPAM by the incorporation of palygorskite

Since the emergence of forward osmosis (FO), low energy requirements, low fouling propensity and high-water recovery have made it one of the most promising water purification technologies. However, there have been few reports focusing on the treatment of polymer flooding produced water (PFPW) using FO technology up to now. In the present work, porous FO membranes with/without palygorskite (Pal) nanoparticles were utilized as the separation membrane to evaluate the potential of a porous FO membrane in the treatment of oily wastewater containing HPAM and the effect of Pal nanoparticles on the FO performance was investigated. When the loading concentration of Pal in the membrane was 0.75 wt%, the water flux could reach 37.67 L m⁻² h⁻¹ by using 4 g L⁻¹ poly(sodium-p-styrenesulfonate) (PSS) as draw solution under a cross-flow rate of 18.5 cm s⁻¹, which was much higher than that for pure polysulfone (PS) membranes. Besides, the comparison between ultrafiltration (UF) and FO performance in treating HPAM solution indicated that FO possessed better antifouling capacity, since less decline and higher recovery of water flux were observed during the FO process. Furthermore, recycling the draw solution gave an almost unchanged water flux, which suggested the feasibility of draw solute regeneration in the FO process. This work broadens the application field of porous FO technology and may pave a new way in the treatment of PFPW.

Porous forward osmosis (FO) membranes with/without palygorskite (Pal) nanoparticles were utilized as the separation membrane to evaluate the potential of porous FO membrane in the treatment of oily wastewater containing HPAM.

Antifouling and antimicrobial polyethersulfone/hyperbranched polyester-amide/Ag composite

This study provided a facile approach for the development of antifouling and antibacterial polyethersulfone (PES) composite film. Mainly, hyperbranched polyester-amide (PESAM) was used as both the reducing and capping agent for the in situ formation of AgNPs. The nanoparticles were intensively investigated using Fourier transform infrared spectroscopy (FTIR), ultra-violet spectroscopy (UV-vis), scanning and transmission electron microscopy (SEM & TEM) and X-ray diffraction (XRD). AgNPs were narrowly distributed with an average particle size of about 6 nm. PESAM was mixed with PES to realize free-standing film using the phase inversion method. The inclusion of PESAM in the composite film significantly improved hydrophilicity as confirmed by the contact angle measurements. Furthermore, SEM and EDX investigations confirmed that PESAM induced the in situ formation of AgNPs not only on the film surface but also inside its macro-voids. The composite film (PES/PESAM/Ag) displayed significant antibacterial potential against Gram positive and Gram negative bacteria. Overall, the described method paves the way towards development of advanced PES composite films with antimicrobial properties for broad application areas that include desalination membranes or active packaging materials.

This study provided a facile approach for the development of antifouling and antibacterial polyethersulfone (PES) composite film.

ZrO2-TiO2 Incorporated PVDF Dual-Layer Hollow Fiber Membrane for Oily Wastewater Treatment: Effect of Air Gap

Dual-layer hollow fiber (DLHF) nanocomposite membrane prepared by co-extrusion technique allows a uniform distribution of nanoparticles within the membrane outer layer to enhance the membrane performance. The effects of spinning parameters especially the air gap on the physico-chemical properties of ZrO2-TiO2 nanoparticles incorporated PVDF DLHF membranes for oily wastewater treatment have been investigated in this study. The zeta potential of the nanoparticles was measured to be around -16.5 mV. FESEM-EDX verified the uniform distribution of Ti, Zr, and O elements throughout the nanoparticle sample and the TEM images showed an average nanoparticles grain size of ~12 nm. Meanwhile, the size distribution intensity was around 716 nm. A lower air gap was found to suppress the macrovoid growth which resulted in the formation of thin outer layer incorporated with nanoparticles. The improvement in the separation performance of PVDF DLHF membranes embedded with ZrO2-TiO2 nanoparticles by about 5.7% in comparison to the neat membrane disclosed that the incorporation of ZrO2-TiO2 nanoparticles make them potentially useful for oily wastewater treatment.

Production of High Flux Poly(Ether Sulfone) Membrane Using Silica Additive Extracted from Natural Resource

This paper reports the application of silica derived from natural biomasses of rice husk and bagasse ashes as membrane modifying agents. The modification was conducted on poly(ether sulfone) (PES) membrane by blending the silica into the dope solution. The modification was aimed to improve the structure and hydraulic performance of the resulting PES membrane. The effects of silica addition to the membrane system were evaluated through the analysis of change in chemical structure using ATR-FTIR, surface morphological change using AFM, and surface hydrophilicity using water contact angle measurement. SEM and AFM images show the silica loading significantly affects the membranes morphologies. Silica loading also promotes hydrophilic property as shown by the decrease in water contact angles from 82° to 52-60° due to the presence of polar groups in some residual silica in the membrane matrix. Silica blending also leads to the formation of membranes with higher permeability of up to three folds but lower humic acid rejection (78-62%). The findings indicate the role of silica to enhance the membrane pore size. The ability of membrane to reject humic acid (of 0.8 nm minimum diameter) indicating that the resulting membranes were in between tight ultrafiltration and nanofiltration type. Nonetheless, applying too-high silica concentration decreased the humic acid rejection most likely due to over enlargement of the membrane pore size.

Synthesis, characterization and applications of metallic nanoparticles/rGO blended poly methyl methacrylate membranes for the efficient removal of Cd2+ from model and real wastewater

Herein we report the fabrication of polymer blended hybrid membranes from poly methyl methacrylate (PMMA) as a matrix, and reduced graphene oxide (rGO) and Fe₂O₃, ZnO, CuO and AgO nanoparticles (NPs) as primary and secondary fillers, respectively.

Nano CuO/g-C3N4 sheets-based ultrafiltration membrane with enhanced interfacial affinity, antifouling and protein separation performances for water treatment application

To improve the interfacial affinity and antifouling properties of polyphenylsulfone (PPSU) membrane, nano CuO/g-C₃N₄ (g-CN) sheets were synthesized via facile calcination route as one pot synthesis method. The uniformly assembled nanohybrid fillers, CuO on g-CN sheets were confirmed by using XRD, TEM, EDX and FTIR analysis. The non-solvent induced phase inversion technique was used to fabricate the nanohybrid ultrafiltration (UF) membranes by doping different concentration (0.5-1 wt.%) of nano CuO/g-C₃N₄ (g-CN) sheets within the PPSU matrix. The results of contact angle, atomic force microscopy, energy-dispersive X-ray spectroscopy reveal that surface structure and physico-chemical properties of nanohybrid membrane plays lead role in solute interaction and rejection compared to bare membrane, M0. Furthermore, the interfacial affinity of membrane was explored in detail via surface free energy, spreading coefficient, wetting tension and reversible work of adhesion analysis. Nanohybrid UF membrane, with 0.5% of the filler (M1) displayed remarkable permeation flux of 202, 131 L/m²/hr for pure water and protein solution, respectively while maintaining a high protein rejection (96%). Moreover, the exceptional dispersion of the nanosheets in the polymer matrix enhanced FRR (79%) and decreased the overall resistance of M1 compared to the pristine membrane (M0). Overall results suggest that the incorporation of nano sheets is a facile modification technique which improves the comprehensive membrane performance and holds a great potential to be further explored for water treatment.

High-flux ultrafiltration membrane with open porous hydrophilic structure using dual pore formers

This work investigated the synergistic effect of polyvinylpyrrolidone (PVP) and hydroxypropyl-beta-cyclodextrin (HP-β-CD) as dual pore forming agents on the properties and performance of polysulfone (PSf) ultrafiltration membranes. A fixed concentration of PVP and varying concentrations of HP-β-CD were used to prepare the membranes using the phase inversion technique. The results showed that the inclusion of these additives in the dope solution increased its thermodynamic instability and promoted instantaneous demixing. Overall, an increase was observed in the hydrophilicity, open porous structure and mechanical strength of the membranes. Cross-flow filtration tests demonstrated that the pure water permeability of the fabricated membrane was 891 LMH bar^-1, about 4.37 times higher than the pristine membrane, while bovine serum albumin (BSA) rejection was relatively constant (about 93%) for all the fabricated membranes. This work proposed that the addition of HP-β-CD and PVP as dual pore formers can produce a viable ultrafiltration membrane with improved water permeability without a middle ground on rejection potential.

Fabrication of Tween-20 coated PVDF membranes for wastewater treatment: optimization of preparation parameters, removal and membrane fouling control performance

In the present study, polyoxyethylene (20) sorbitan monolaurate (Tween-20) was employed as a surface coating agent for hydrophilic modification of poly(vinylidene fluoride) microfiltration membranes.

Polyethersulfone Membranes Prepared with 3-Aminopropyltriethoxysilane Modified Alumina Nanoparticles for Cu(II) Removal from Water

In this study, 3-aminopropyltriethoxysilane (APTES) modified γ-alumina nanoparticles were utilized to improve the copper removal efficiency of polyethersulfone (PES) membranes. Alumina nanoparticles were first modified by APTES silane coupling agent before impregnating into PES composite membranes. The PES membranes were fabricated by incorporating three different amounts of modified nanoparticles by a phase inversion process. The prepared membranes were characterized using field emission scanning electron microscopy, Fourier transform infrared, X-ray diffraction, thermogravimetric analysis (TGA), dynamic mechanical analysis, water contact angle, water flux, and porosity measurements. The Cu(II) removal and adsorption capacity of the membranes were also analyzed. The addition of nanoparticles increased the thermal stability, hydrophilicity, total porosity, Brunauer-Emmett-Teller surface area, and glass transition temperature of the membranes. TGA confirmed a suitable uptake of the nanoparticles during the membrane fabrication process. The water permeation of the membranes also increased significantly. Membranes synthesized with 4 wt % nanoparticles showed the highest rejection for copper ions of 87%. Adsorption isotherms were tested using Langmuir and Freundlich models, where the Freundlich isotherm model resulted in the best fitting.

Recent advances in hydrophilic modification and performance of polyethersulfone (PES) membrane via additive blending

The blending of additives in the polyethersulfone (PES) matrix is an important approach in the membrane industry to reduce membrane hydrophobicity and improve the performance (flux, solute rejection, and reduction of fouling). Several (hydrophilic) modifications of the PES membrane have been developed. Given the importance of the hydrophilic modification methods for PES membranes and their applications, we decided to dedicate this review solely to this topic. The types of additives embedded into the PES matrix can be divided into two main categories: (i) polymers and (ii) inorganic nanoparticles (NPs). The introduced polymers include polyvinylpyrrolidone, chitosan, polyamide, polyethylene oxide, and polyethylene glycol. The introduced nanoparticles discussed include titanium, iron, aluminum, silver, zirconium, silica, magnesium based NPs, carbon, and halloysite nanotubes. In addition, the applications of hydrophilic PES membranes are also reviewed. Reviewing the research progress in the hydrophilic modification of PES membranes is necessary and imperative to provide more insights for their future development and perhaps to open the door to extend their applications to other more challenging areas.

Highly permeable and stable forward osmosis (FO) membrane based on the incorporation of Al2O3 nanoparticles into both substrate and polyamide active layer

In the present study, hydrophilic Al₂O₃ nanoparticles were used as additives in both substrate and polyamide active (PA) layer to improve forward osmosis (FO) membrane properties.