Coupling of membrane filtration and advanced oxidation processes for removal of pharmaceutical residues: A critical review

Evaluation of direct photolysis and UVC/H 2 O 2 process in the oxidation of benzoic acid: experimental and numerical analysis

Produced water management is a significant challenge for the oil and gas industry. Due to the large volumes and complex composition of this water, treatment requires special attention, resulting in high costs for companies in the sector. Naphthenic acids, known for their recalcitrance, add a layer of complexity to the treatment process. Benzoic acid, a simple aromatic carboxylic acid, has been extensively studied due to its structural similarity to naphthenic acids, highlighting its importance in developing treatment strategies. Advanced oxidative processes, such as UV/H2 O2 , have emerged as promising alternatives for the degradation of recalcitrant organic pollutants. This study aims to enhance the UV/H2 O2 process through experiments, kinetic mechanisms, and mathematical models that allow the simulation of various experimental conditions, providing a clearer and more economical approach to produced water treatment in the oil and gas industry. The results indicate that the oxidation of benzoic acid by the UV/H2 O2 process achieved removals between 12.29 and 83.56% in a batch reactor over 120 min. Additionally, the influence of solution pH and H2 O2 concentration was significant, with better removal rates observed at pH 3. The molar extinction coefficient of benzoic acid was also found to be pH-dependent, indicating a greater photon absorption capacity at lower pH. The mathematical model developed for the UV/H2 O2 process accurately predicted experimental data and process variable effects, offering valuable insights into reaction kinetics and the influence of experimental conditions.

Characteristics and functional bacteria of an efficient benzocaine-mineralizing bacterial consortium

The extensive use of pharmaceutical and personal care products (PPCPs) has led to widespread residual pollution, which increases the risk of the development of drug resistance in pathogenic microorganisms. Benzocaine is a PPCP that is widely used medical anesthesia and in sunscreen. Microorganisms are essential for the degradation of residual PPCPs. However, no studies have reported the microbial degradation of benzocaine. In this study, through continuous enrichment of the initial consortium HJ1, the highly efficient benzocaine-degrading consortium HJ7 was obtained, HJ7 exhibited a degradation rate that was 1.92 times greater than that of HJ1. Methyl 4-aminobenzoate and 4-aminobenzoic acid were identified as major intermediate products during benzocaine biodegradation by consortium HJ1 or HJ7. Methylobacillus (57.8 % ± 0.9 %) and Pseudomonas (22.1 % ± 0.7 %), which are thought to harbor essential species for benzocaine degradation, were significantly enriched in consortium HJ7. Two benzocaine-degrading strains, Pseudomonas sp. A8 and Microbacterium sp. A741, and one methyl 4-aminobenzoate-degrading strain, Achromobacter sp. A5, were isolated from consortium HJ7, and they synergistically mineralized benzocaine. These findings not only provide new insights into the biotransformation of benzocaine but also provide strain resources for the bioremediation of residual benzocaine in the environment.

Removal of fluoroquinolone antibiotic and sulfonated dye by functionalized Persea americana seed powder: Appraisal on phase transfer kinetics, equilibrium, economics, and applications in rural settings

The study focuses on reactive orange 16 (RO16), a sulfonated dye, and ciprofloxacin (CiP), a fluoroquinolone antibiotic treatment from aquatic surface by adsorption. The functionalized Persea americana seed powder (PASP) was developed by acid hydrolysis technique and investigated for RO16 and CiP removal in batch scale at different concentrations for CiP and RO16, pH (2-8), contact duration and temperature (303-318K). Utilizing a scanning electron microscope (SEM) with energy dispersive X-ray spectroscopy (EDAX), the generated native PASP were assessed for their morphological characteristics. Fourier transform infrared (FTIR) spectroscopy was applied to examine the performing characteristics of PASP. Experimental findings with four kinetic mathematical models allowed the estimation of the process involved in the biosorption. The most effective agreement was explained by the pseudo-second-order model and Sips isotherm (Cip = 34.603 mg/g and RO16 = 30.357 mg/g) at 303K temperature. For Cip Process economics of the biosorbent was done, and it was observed that it was less than the readily market-available activated carbon.

Advancements in Inorganic Membrane Filtration Coupled with Advanced Oxidation Processes for Wastewater Treatment

Membrane filtration is an effective water recycling and purification technology to remove various pollutants in water. Inorganic membrane filtration (IMF) technology has received widespread attention because of its unique high temperature and corrosion resistance. Commonly used inorganic membranes include ceramic membranes and carbon-based membranes. As novel catalytic inorganic membrane processes, IMF coupled with advanced oxidation processes (AOPs), can realize the separation and in situ degradation of pollutants, thus mitigating membrane contamination. In this paper, the types and performance of IMF are discussed. The influencing factors of inorganic membranes in practical wastewater treatment are summarized. The applications, advantages, and disadvantages of the coupled process of IMF and AOPs are summarized and outlined. Finally, the challenges and prospects of IMF and IMF coupled with AOPs are presented, respectively. This contributes to the design and development of coupled systems of membrane filtration with inorganic materials and IMF coupled with AOPs for practical wastewater treatment.

A review on reactive oxygen species generation, anode materials and operating parameters in sonoelectrochemical oxidation for wastewater remediation

The application of sonoelectrochemical (SEC) oxidation technique involving the incorporation of ultrasound irradiation into an electrochemical oxidation system has found enormous success for various purposes, especially for organic synthesis and water treatment. Although its industrial application towards the removal of organic contaminants in water is not popular, its success on the laboratory scale is often attributed to the physical and chemical effects. These effects arise from the influence of ultrasound irradiation, thus eliminating electrode passivation or fouling, improving mass transfer and enhancing reactive oxygen species (ROS) generation. The continuous activation of the electrode surface, improved reaction kinetics and other associated advantages are equally occasioned by acoustic streaming and cavitation. This review hereby outlines common ROS generated in SEC oxidation and pathways to their generation. Furthermore, classes of materials commonly employed as anodes and the influence of prominent operational parameters on the performance of the technique for the degradation of organic pollutants in water are extensively discussed. Hence, this study seeks to broaden the significant promises offered by SEC oxidation to environmentally sustainable technology advances in water treatment and pollution remediation.

Tempospatially Confined Catalytic Membranes for Advanced Water Remediation

The application of homogeneous catalysts in water remediation is limited by their excessive chemical and energy input, weak regenerability, and potential leaching. Heterogeneous catalytic membranes (CMs) offer a new approach to facilitate efficient, selective, and continuous pollutant degradation. Thus, integrating membranes and continuous filtration with heterogeneous advanced oxidation processes (AOPs) can promote thermodynamic and kinetic mass transfers in spatially confined intrapores and facilitate diffusion-reaction processes. Despite the remarkable advantages of heterogeneous CMs, their engineering application is practically restricted due to the fuzzy design criteria for specific applications. Herein, the recent advances in CMs for advanced water remediation are critically reviewed and the design flow for tempospatially confined CMs is proposed. Further, state-of-the-art CM materials and their catalytic mechanisms are reviewed, after which the tempospatial confinement mechanisms comprising the nanoconfinement effect, interface effect, and kinetic mass transfer are emphasized, thus clarifying their roles in the construction and performance optimization of CMs. Additionally, the fabrication methods for CMs based on their catalysts and pore sizes are summarized and an overview of their application and performance evaluations is presented. Finally, future directions for CMs in materials research and water treatment, are presented.

Sustainable approach for the treatment of dye-containing wastewater – a critical review

In the world’s rapidly expanding economy, textile industries are recognized as a substantial contributor to economic growth, but they are one of the most significant polluting industrial sectors. Dye-contaminated water sources can pose serious public health concerns, including toxicity, mutagenicity, and carcinogenicity among other adverse health effects. Despite a limited understanding of efficacious decolorization methodologies, the pursuit of a sustainable strategy for the treatment of a wide spectrum of dyes remains a formidable challenge. This article conducted an exhaustive review of extant literature pertaining to diverse physical, chemical, biological, and hybrid processes with the aim of ascertaining their efficacy. It also elucidates the advantages and disadvantages, cost considerations, as well as scalability impediments of the treatment methodologies, thereby facilitating the identification of optimal strategies for establishing techno-economically efficient processes in the sustainable handling of these effluents. The hybrid configuration exhibited superior efficiency and was documented to surmount the limitations and constraints inherent to individual techniques. The study also revealed that most of the proven and established dye removal techniques share a common limitation viz., the generation of secondary pollution (i.e., sludge generation, toxic intermediates, etc.) to the ecosystem.

Removal of 6-methylquinoline from shale gas wastewater using electrochemical carbon nanotubes filter

6-Methylquinoline (6-MQ) is identified as a high-concentration organic compound pervasive in shale gas wastewater (SGW) and poses a significant risk of environmental pollution. In response, this study aimed to address these challenges by introducing an innovative electrochemical membrane constructed with multi-walled carbon nanotubes (CNTs) for the removal of 6-MQ. The investigation systematically explored the impact of voltage, initial pollutant concentration, and salinity on the performance of the electrochemical CNTs filter. It was found a positive correlation between removal efficiency and increasing voltage and salinity levels. Conversely, as the initial concentration of pollutants increased, the efficiency showed a diminishing trend. The electrochemical CNTs filter exhibited remarkable efficacy in both adsorption removal and electrochemical oxidation of 6-MQ. Notably, the CNTs membrane exhibited robust adsorption capabilities, evidenced by the sustained adsorption of 6-MQ for over 33 h. Furthermore, applying an electrochemical oxidation voltage of 3 V consistently maintained a removal rate exceeding 34.0% due to both direct and indirect oxidation, underscoring the sustained efficacy of the electrochemical membranes. Besides, real wastewater experiments, while displaying a reduction in removal efficiency compared to synthetic wastewater experiments, emphasized the substantial potential of the electrochemical CNTs filter for practical applications. This study underscores the significant promise of electrochemical membranes in addressing low molecular weight contaminants in SGW, contributing valuable insights for advancing SGW treatment strategies.

Selective Heterogeneous Fenton Degradation of Formaldehyde Using the Fe-ZSM-5 Catalyst

As a toxic Volatile Organic Pollutant (TVOC), formaldehyde has a toxic effect on microorganisms, consequently inhibiting the biochemical process of formaldehyde wastewater treatment. Therefore, the selective degradation of formaldehyde is of great significance in achieving high-efficiency and low-cost formaldehyde wastewater treatment. This study constructed a heterogeneous Fe-ZSM-5/H2O2 Fenton system f or the selective degradation of target compounds. By immobilizing Fe3+ onto the surface of a ZSM-5 molecular sieve, Fe-ZSM-5 was prepared successfully. XRD, BET and FT-IR spectral studies showed that Fe-ZSM-5 was mainly composed of micropores. The influences of different variables on formaldehyde-selective heterogeneous Fenton degradation performance were studied. The 93.7% formaldehyde degradation and 98.2% selectivity of formaldehyde compared with glucose were demonstrated in the optimized Fenton system after 360 min. Notably, the resultant selective Fenton oxidation system had a wide range of pH suitability, from 3.0 to 10.0. Also, the Fe-ZSM-5 was used in five consecutive cycles without a significant drop in formaldehyde degradation efficiency. The use of reactive oxygen species scavengers indicated that the hydroxyl radical was the primary active species responsible for degrading formaldehyde. Furthermore, great degradation performance was acquired with high concentrations of formaldehyde for this system, and the degradation efficiency was more than 95.0%.

A comprehensive review and perspective research in technology integration for the treatment of gaseous volatile organic compounds

Volatile organic compounds (VOCs) are harmful pollutants emitted from industrial processes. They pose a risk to human health and ecosystems, even at low concentrations. Controlling VOCs is crucial for good air quality. This review aims to provide a comprehensive understanding of the various methods used for controlling VOC abatement. The advancement of mono-functional treatment techniques, including recovery such as absorption, adsorption, condensation, and membrane separation, and destruction-based methods such as natural degradation methods, advanced oxidation processes, and reduction methods were discussed. Among these methods, advanced oxidation processes are considered the most effective for removing toxic VOCs, despite some drawbacks such as costly chemicals, rigorous reaction conditions, and the formation of secondary chemicals. Standalone technologies are generally not sufficient and do not perform satisfactorily for the removal of hazardous air pollutants due to the generation of innocuous end products. However, every integration technique complements superiority and overcomes the challenges of standalone technologies. For instance, by using catalytic oxidation, catalytic ozonation, non-thermal plasma, and photocatalysis pretreatments, the amount of bioaerosols released from the bioreactor can be significantly reduced, leading to effective conversion rates for non-polar compounds, and opening new perspectives towards promising techniques with countless benefits. Interestingly, the three-stage processes have shown efficient decomposition performance for polar VOCs, excellent recoverability for nonpolar VOCs, and promising potential applications in atmospheric purification. Furthermore, the review also reports on the evolution of mathematical and artificial neural network modeling for VOC removal performance. The article critically analyzes the synergistic effects and advantages of integration. The authors hope that this article will be helpful in deciding on the appropriate strategy for controlling interested VOCs.

Adsorptive removal of diclofenac sodium from aqueous solution by highly efficient metal organic framework (UiO-66)/multi-walled carbon nanotube composite

In the current study, synthesis and use of a novel adsorbent (composite in nature) are presented for treatment of one of the most commonly found pharmaceutical compound, viz, diclofenac sodium (DCF) in waste water. Synthesis of the composite adsorbent was done by hydrothermal method metal organic framework (MOF) based on Zr metal and multi-walled carbon nanotube (MWCNT). The composite adsorbent is termed as UiO-66/MWCNT. The confirmation of successful synthesis of the adsorbent is done with the help of sophisticated characterization techniques like FTIR, XRD, zeta potential analyser, and SEM. The synthesized composite adsorbent is found to have good adsorption capacity for DCF. The experiments related to the process of adsorption were done in batch mode and the significance of various operating parameters affecting the specific uptake of DCF. Maximum adsorption is observed at 3 pH (acidic condition) when the initial concentration of DCF and adsorbent dose was 30 mg/L and 100 mg/L, respectively. The Langmuir isotherm model best describes the process of adsorption with a maximum adsorption capacity of 256.41 mg/g. Experimental results obtained through the studies conducted related to the kinetics displayed that the process followed pseudo-second order model, and intraparticle studies suggested that diffusion through pores controls the rate. Thermodynamic studies suggest that the adsorption of DCF on UiO-66/MWCNT was completely spontaneous with ΔH = -22.089 kJ/mol. The possible mechanism for the adsorptive removal of DCF through UiO-66/MWCNT as found from this study is electrostatic interaction.

Ecotoxicological impacts of landfill sites: Towards risk assessment, mitigation policies and the role of artificial intelligence

Waste disposal in landfills remains a global concern. Despite technological developments, landfill leachate poses a hazard to ecosystems and human health since it acts as a secondary reservoir for legacy and emerging pollutants. This study provides a systematic and scientometric review of the nature and toxicity of pollutants generated by landfills and means of assessing their potential risks. Regarding human health, unregulated waste disposal and pathogens in leachate are the leading causes of diseases reported in local populations. Both in vitro and in vivo approaches have been employed in the ecotoxicological risk assessment of landfill leachate, with model organisms ranging from bacteria to birds. These studies demonstrate a wide range of toxic effects that reflect the complex composition of leachate and geographical variations in climate, resource availability and management practices. Based on bioassay (and other) evidence, categories of persistent chemicals of most concern include brominated flame retardants, per- and polyfluorinated chemicals, pharmaceuticals and alkyl phenol ethoxylates. However, the emerging and more general literature on microplastic toxicity suggests that these particles might also be problematic in leachate. Various mitigation strategies have been identified, with most focussing on improving landfill design or leachate treatment, developing alternative disposal methods and reducing waste volume through recycling or using more sustainable materials. The success of these efforts will rely on policies and practices and their enforcement, which is seen as a particular challenge in developing nations and at the international (and transboundary) level. Artificial intelligence and machine learning afford a wide range of options for evaluating and reducing the risks associated with leachates and gaseous emissions from landfills, and various approaches tested or having potential are discussed. However, addressing the limitations in data collection, model accuracy, real-time monitoring and our understanding of environmental impacts will be critical for realising this potential.

Easily scale 3D conductive gradient fiber membrane for contaminants removal and fouling mitigation under electrochemical assistance

An electrochemical membrane filtration system provides an innovative approach to enhance contaminant removal and mitigate membrane fouling. There is an urgent need to develop portable, versatile, and efficient electrochemical membranes for affordable wastewater treatment. Here, a 3D conductive gradient fiber membrane (CC/PVDF) with a gradient porous structure was prepared using a two-step phase inversion method. Methyl orange (MO) was utilized as model organic substance to investigate the electrochemical performance of the CC/PVDF membrane. At applied potentials of +2 V, +3 V, -2 V and -3 V, the removal efficiency of MO was 5.1, 5.3, 4.8, and 5.1 times higher than at 0 V. A dramatic flux loss of 35.02% occurred on the membrane without electrochemistry, interestingly, whereas the flux losses were only 23.59%-10.24% in the applied potential after 30 min of filtration, which were approximately 1.18, 1.28, 1.29 and 1.38 times as high as that without electrochemistry, respectively. The enhanced removal and anti-fouling performances of the membranes were attributed to the functions of electrochemical degradation, electrostatic repulsion, and electrically enhanced wettability. Electrochemical generation of Hydrogen peroxide, along with HO• radicals, was detected and direct electron transfer and HO• were proved to be the dominant oxidants responsible for MO degradation. The intermediate oxidation products were identified by mass spectrometry, and an electrochemical degradation pathway of MO was proposed based on bond-breaking oxidation, ring-opening reactions, and complete oxidation. All the findings emphasize that the ECMF system possesses superior efficiency and creative potential for water purification applications.

Recent advances in electrospinning-nanofiber materials used in advanced oxidation processes for pollutant degradation

Electrospun nanofiber membranes have emerged as a novel catalyst, demonstrating exceptional efficacy in advanced oxidation processes (AOPs) for the degradation of organic pollutants. Their superior performance can be attributed to their substantial specific surface area, high porosity, ease of modification, rapid recovery, and unparalleled chemical stability. This paper aims to comprehensively explore the progressive applications and underlying mechanisms of electrospun nanofibers in AOPs, which include Fenton-like processes, photocatalysis, catalytic ozonation, and persulfate oxidation. A detailed discussion on the mechanism and efficiency of the catalytic process, which is influenced by the primary components of the electrospun catalyst, is presented. Additionally, the paper examines how concentration, viscosity, and molecular weight affect the characteristics of the spinning materials and seeks to provide a thorough understanding of electrospinning technology to enhance water treatment methods. The review proposes that electrospun nanofiber membranes hold significant potential for enhancing water treatment processes using advanced oxidation methods. This is attributed to their advantageous properties and the tunable nature of the electrospinning process, paving the way for advancements in water treatment through AOPs.

Efficacy of new generation biosorbents for the sustainable treatment of antibiotic residues and antibiotic resistance genes from polluted waste effluent

Antimicrobials are frequently used in both humans and animals for the treatment of bacterially-generated illnesses. Antibiotic usage has increased for more than 40% from last 15 years globally per day in both human populations and farm animals leading to the large-scale discharge of antibiotic residues into wastewater. Most antibiotics end up in sewer systems, either directly from industry or healthcare systems, or indirectly from humans and animals after being partially metabolized or broken down following consumption. To prevent additional antibiotic compound pollution, which eventually impacts on the spread of antibiotic resistance, it is crucial to remove antibiotic residues from wastewater. Antibiotic accumulation and antibiotic resistance genes cannot be effectively and efficiently eliminated by conventional sewage treatment plants. Because of their high energy requirements and operating costs, many of the available technologies are not feasible. However, the biosorption method, which uses low-cost biomass as the biosorbent, is an alternative technique to potentially address these problems. An extensive literature survey focusing on developments in the field was conducted using English language electronic databases, such as PubMed, Google Scholar, Pubag, Google books, and ResearchGate, to understand the relative value of the available antibiotic removal methods. The predominant techniques for eliminating antibiotic residues from wastewater were categorized and defined by example. The approaches were contrasted, and the benefits and drawbacks were highlighted. Additionally, we included a few antibiotics whose removal from aquatic environments has been the subject of extensive research. Lastly, a few representative publications were identified that provide specific information on the removal rates attained by each technique. This review provides evidence that biosorption of antibiotic residues from biological waste using natural biosorbent materials is an affordable and effective technique for eliminating antibiotic residues from wastewater.

Electric Field-Assisted Nanofiltration for PFOA Removal with Exceptional Flux, Selectivity, and Destruction

Per- and polyfluoroalkyl substances (PFAS) pose significant environmental and human health risks and thus require solutions for their removal and destruction. However, PFAS cannot be destroyed by widely used removal processes like nanofiltration (NF). A few scarcely implemented advanced oxidation processes can degrade PFAS. In this study, we apply an electric field to a membrane system by placing a nanofiltration membrane between reactive electrodes in a crossflow configuration. The performance of perfluorooctanoic acid (PFOA) rejection, water flux, and energy consumption were evaluated. The reactive and robust SnO2-Sb porous anode was created via a sintering and sol-gel process. The characterization and analysis techniques included field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), ion chromatography, mass spectroscopy, porosimeter, and pH meter. The PFOA rejection increased from 45% (0 V) to 97% (30 V) when the electric field and filtration were in the same direction, while rejection capabilities worsened in opposite directions. With saline solutions (1 mM Na2SO4) present, the induced electro-oxidation process could effectively mineralize PFOA, although this led to unstable removal and water fluxes. The design achieved an exceptional performance in the nonsaline feed of 97% PFOA rejection and water flux of 68.4 L/m2 hr while requiring only 7.31 × 10-5 kWh/m3/order of electrical energy. The approach's success is attributed to the proximity of the electrodes and membrane, which causes a stronger electric field, weakened concentration polarization, and reduced mass transfer distances of PFOA near the membrane. The proposed electric field-assisted nanofiltration design provides a practical membrane separation method for PFAS removal from water.

Electrochemical-based processes for produced water and oily wastewater treatment: A review

The greatest volume of by-products produced in oil and gas recovery operations is referred to as produced water and increasing environmental concerns and strict legislations on discharging it into the environment cause to more attention for focusing on degradation methods for treatment of produced water especially electrochemical technologies. This article provides an overview of electrochemical technologies for treating oily wastewater and produced water, including: electro-coagulation, electro-Fenton, electrochemical oxidation and electrochemical membrane reactor as a single stage and combination of these technologies as multi-stage treatment process. Many researchers have carried out experiments to examine the impact of various factors such as material (i.e, electrode material) and operational conditions (i.e., potential, current density, pH, electrode distance, and other factors) for organic elimination to obtain the high efficiency. Results of each method are reviewed and discussed according to these studies, comprehensively. Furthermore, several challenges need to be overcome and perspectives for future study are proposed for each method.

Preparation of a Molecularly Imprinted Silica Nanoparticles Embedded Microfiltration Membrane for Selective Separation of Tetrabromobisphenol A from Water

The ubiquitous presence of tetrabromobisphenol A (TBBPA) in aquatic environments has caused severe environmental and public health concerns; it is therefore of great significance to develop effective techniques to remove this compound from contaminated waters. Herein, a TBBPA imprinted membrane was successfully fabricated via incorporating imprinted silica nanoparticles (SiO₂ NPs). The TBBPA imprinted layer was synthesized on the 3-(methacryloyloxy) propyltrimethoxysilane (KH-570) modified SiO₂ NPs via surface imprinting. Eluted TBBPA molecularly imprinted nanoparticles (E-TBBPA-MINs) were incorporated onto a polyvinylidene difluoride (PVDF) microfiltration membrane via vacuum-assisted filtration. The obtained E-TBBPA-MINs embedded membrane (E-TBBPA-MIM) showed appreciable permeation selectivity toward the structurally analogous to TBBPA (i.e., 6.74, 5.24 and 6.31 of the permselectivity factors for p-tert-butylphenol (BP), bisphenol A (BPA) and 4,4'-dihydroxybiphenyl (DDBP), respectively), far superior to the non-imprinted membrane (i.e., 1.47, 1.17 and 1.56 for BP, BPA and DDBP, respectively). The permselectivity mechanism of E-TBBPA-MIM could be attributed to the specific chemical adsorption and spatial complementation of TBBPA molecules by the imprinted cavities. The resulting E-TBBPA-MIM exhibited good stability after five adsorption/desorption cycles. The findings of this study validated the feasibility of developing nanoparticles embedded molecularly imprinted membrane for efficient separation and removal of TBBPA from water.

Preparation of Fe/Ni-MOFs for the Adsorption of Ciprofloxacin from Wastewater

This work studies the use of Fe/Ni-MOFs for the removal of ciprofloxacin (CIP) in wastewater. Fe/Ni-MOFs are prepared by the solvothermal method and characterized by X-ray diffraction (XRD), a scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR), and a thermal gravimetric analyzer (TG). Under the conditions of the concentration of 50 ppm, a mass of 30 mg, and a temperature of 30 °C, the maximum adsorption capacity of ciprofloxacin removal within 5 h was 232.1 mg/g. The maximum removal rate was 94.8% when 40 mg of the Fe/Ni-MOFs was added to the solution of 10 ppm ciprofloxacin. According to the pseudo-second-order (PSO) kinetic model, the R² values were all greater than 0.99, which proved that the adsorption theory of ciprofloxacin by Fe/Ni-MOFs was consistent with the practice. The adsorption results were mainly affected by solution pH and static electricity, as well as other factors. The Freundlich isotherm model characterized the adsorption of ciprofloxacin by Fe/Ni-MOFs as multilayer adsorption. The above results indicated that Fe/Ni-MOFs were effective in the practical application of ciprofloxacin removal.

Introducing machine learning model to response surface methodology for biosorption of methylene blue dye using Triticum aestivum biomass

A major environmental problem on a global scale is the contamination of water by dyes, particularly from industrial effluents. Consequently, wastewater treatment from various industrial wastes is crucial to restoring environmental quality. Dye is an important class of organic pollutants that are considered harmful to both people and aquatic habitats. The textile industry has become more interested in agricultural-based adsorbents, particularly in adsorption. The biosorption of Methylene blue (MB) dye from aqueous solutions by the wheat straw (T. aestivum) biomass was evaluated in this study. The biosorption process parameters were optimized using the response surface methodology (RSM) approach with a face-centred central composite design (FCCCD). Using a 10 mg/L concentration MB dye, 1.5 mg of biomass, an initial pH of 6, and a contact time of 60 min at 25 °C, the maximum MB dye removal percentages (96%) were obtained. Artificial neural network (ANN) modelling techniques are also employed to stimulate and validate the process, and their efficacy and ability to predict the reaction (removal efficiency) were assessed. The existence of functional groups, which are important binding sites involved in the process of MB biosorption, was demonstrated using Fourier Transform Infrared Spectroscopy (FTIR) spectra. Moreover, a scan electron microscope (SEM) revealed that fresh, shiny particles had been absorbed on the surface of the T. aestivum following the biosorption procedure. The bio-removal of MB from wastewater effluents has been demonstrated to be possible using T. aestivum biomass as a biosorbent. It is also a promising biosorbent that is economical, environmentally friendly, biodegradable, and cost-effective.

An Overview of Photocatalytic Membrane Degradation Development

Environmental pollution has become a worldwide issue. Rapid industrial and agricultural practices have increased organic contaminants in water supplies. Hence, many strategies have been developed to address this concern. In order to supply clean water for various applications, high-performance treatment technology is required to effectively remove organic and inorganic contaminants. Utilizing photocatalytic membrane reactors (PMRs) has shown promise as a viable alternative process in the water and wastewater industry due to its efficiency, low cost, simplicity, and low environmental impact. PMRs are commonly categorized into two main categories: those with the photocatalyst suspended in solution and those with the photocatalyst immobilized in/on a membrane. Herein, the working and fouling mechanisms in PMRs membranes are investigated; the interplay of fouling and photocatalytic activity and the development of fouling prevention strategies are elucidated; and the significance of photocatalysis in membrane fouling mechanisms such as pore plugging and cake layering is thoroughly explored.

Hybrid system coupling ozonation and nanofiltration with functionalized catalytic ceramic membrane for ibuprofen removal

The investigations on the removal of ibuprofen (IBU) in a hybrid system coupling ozonation and nanofiltration with functionalized catalytic ceramic membrane are presented. The gaseous ozone into feed water in concentration of 11 g Nm^-3 was supplied. Positive influence of catalytic ozonation on ibuprofen decomposition was observed. The application of catalytic nanofiltration membrane led to the ibuprofen removal of 91% after the first 15 min from the beginning of the O₃/NF process, while at the same time, for the pristine membrane, it was equal to 76%. The investigations revealed incomplete degradation of drug under pH 3 after 2 h, i.e., 89%. On the other hand, the addition of inorganic salts did not affect the catalytic ibuprofen removal efficiency. Under acidic pH, the highest permeate flux decline (26%) was noted, whereas no differences between permeate flux measured under natural and alkaline conditions were observed. During the treatment process, three IBU by-products were detected, which significantly affected the permeate toxicity; however, after 2 h of catalytic nanofiltration, the product of treatment process was found as non-toxic.

Eco-friendly fabrication of multifunctional magnetic plasmonic photocatalyst for adsorption, SERS monitoring and photodegradation of residual fluoroquinolone antibiotics in water

In this work, a kind of multifunctional magnetic plasmonic photocatalyst was prepared by a green and efficient process. Magnetic mesoporous anatase titanium dioxide (Fe₃O₄@mTiO₂) was synthesized by microwave-assisted hydrothermal, and Ag NPs were simultaneously in-situ grown on Fe₃O₄@mTiO₂ (Fe₃O₄@mTiO₂@Ag), graphene oxide (GO) was then wrapped on Fe₃O₄@mTiO₂@Ag (Fe₃O₄@mTiO₂@Ag@GO) to increase its adsorption capacity for fluoroquinolone antibiotics (FQs). Owing to the localized surface plasmon resonance (LSPR) effect of Ag, as well as the photocatalytic capacity of TiO₂, a multifunctional platform based on Fe₃O₄@mTiO₂@Ag@GO was constructed for adsorption, surface-enhanced Raman spectroscopy (SERS) monitoring and photodegradation of FQs in water. The quantitative SERS detection of norfloxacin (NOR), ciprofloxacin (CIP), and enrofloxacin (ENR) was demonstrated with LOD of 0.1 μg mL^-1, and the qualitative analysis was confirmed by density functional theory (DFT) calculation. The photocatalytic degradation rate of NOR over Fe₃O₄@mTiO₂@Ag@GO was about 4.6 and 1.4 times faster than that of Fe₃O₄@mTiO₂ and Fe₃O₄@mTiO₂@Ag, indicating the synergetic effects of Ag NPs and GO, the used Fe₃O₄@mTiO₂@Ag@GO can be easily recovered and recycled for at least 5 times. Thus, the eco-friendly magnetic plasmonic photocatalyst provided a potential solution for the removal and monitoring of residual FQs in environmental water.

Removal of Toxic Metals from Water by Nanocomposites through Advanced Remediation Processes and Photocatalytic Oxidation

Purpose of Review

Heavy and toxic metals are becoming more prevalent in the water sources of the globe, which has detrimental repercussions for both human health and the health of ecosystems. The summary of recent findings on treatment possibilities of toxic metal species by nanomaterials should facilitate the development of more advanced techniques of their removal.

Recent Findings

The high concentrations of chromium, mercury, and arsenic identified in wastewater cause a hazard to human health. There is a wide variety of nanoadsorbents and nanophotocatalysts used for heavy/hazardous metal removal. Recent research has resulted in the production of advanced nanostructures that exhibit extraordinary heavy/hazardous metal adsorption effectiveness and photocatalytic diminution of metal ions. These nanostructures have physically and chemically tunable features.

Summary

In this review article, the use of carbon-based nanomaterials, polymer-based nanomaterials, and semiconductor-based nanomaterials are extensively discussed to remove mercury, chromium, and arsenic ions from wastewater by the adsorption process. Advanced nanomaterials involved in photocatalytic reduction are also comprehensively discussed.

Kinetic Effects of Ciprofloxacin, Carbamazepine, and Bisphenol on Biomass in Membrane Bioreactor System at Low Temperatures to Treat Urban Wastewater

This study analysed the kinetic results in the presence and absence of micropollutants (bisphenol A, carbamazepine, ciprofloxacin, and the mixture of the three compounds) obtained with respirometric tests with mixed liquor and heterotrophic biomass in a membrane bioreactor (MBR) working for two different hydraulic retention times (12-18 h) and under low-temperature conditions (5-8 °C). Independently of the temperature, the organic substrate was biodegraded faster over a longer hydraulic retention time (HRT) with similar doping, which was probably due to the longer contact time between the substrate and microorganisms within the bioreactor. However, low values of temperature negatively affected the net heterotrophic biomass growth rate, with reductions from 35.03 to 43.66% in phase 1 (12 h HRT) and from 37.18 to 42.77% in phase 2 (18 h HRT). The combined effect of the pharmaceuticals did not worsen the biomass yield compared with the effects caused individually.

Poly(vinylidene fluoride) membrane with immobilized TiO2 for degradation of steroid hormone micropollutants in a photocatalytic membrane reactor

The lack of effective technologies to remove steroid hormones (SHs) from aquatic systems is a critical issue for both environment and public health. The performance of a flow-through photocatalytic membrane reactor (PMR) with TiO₂ immobilized on a photostable poly(vinylidene fluoride) membrane (PVDF-TiO₂) was evaluated in the context of SHs degradation at concentrations from 0.05 to 1000 µg/L under UV exposure (365 nm). A comprehensive investigation into the membrane preparation approach, including varying the surface Ti content and distribution, and membrane pore size, was conducted to gain insights on the rate-limiting steps for the SHs degradation. Increasing surface Ti content from 4 % to 6.5 % enhanced the 17β-estradiol (E2) degradation from 46 ± 12-81 ± 6 %. Apparent degradation kinetics were independent of both TiO₂ homogeneity and membrane pore size (0.1-0.45 µm). With optimized conditions, E2 removal was higher than 96 % at environmentally relevant feed concentration (100 ng/L), a flux of 60 L/m²h, 25 mW/cm², and 6.5 % Ti. These results indicated that the E2 degradation on the PVDF-TiO₂ membrane was limited by the catalyst content and light penetration depth. Further exploration of novel TiO₂ immobilization approach that can offer a larger catalyst content and light penetration is required to improve the micropollutant removal efficiency in PMR.

Carbon electrochemical membrane functionalized with flower cluster-like FeOOH catalyst for organic pollutants decontamination

Decorating active catalysts on the reactive electrochemical membrane (REM) is an effective way to further improve its decontamination performance. In this work, a novel carbon electrochemical membrane (FCM-30) was prepared through coating FeOOH nano catalyst on a low-cost coal-based carbon membrane (CM) through facile and green electrochemical deposition. Structural characterizations demonstrated that the FeOOH catalyst was successfully coated on CM, and it grew into a flower cluster-like morphology with abundant active sites when the deposition time was 30 min. The nano FeOOH flower clusters can obviously boost the hydrophilicity and electrochemical performance of FCM-30, which enhance its permeability and bisphenol A (BPA) removal efficiency during the electrochemical treatment. Effects of applied voltages, flow rates, electrolyte concentrations and water matrixes on BPA removal efficiency were investigated systematically. Under the operation condition of 2.0 V applied voltage and 2.0 mL·min^-1 flow rate, FCM-30 can achieve the high removal efficiency of 93.24% and 82.71% for BPA and chemical oxygen demand (COD) (71.01% and 54.89% for CM), respectively, with only a low energy consumption (EC) of 0.41 kWh·kgCOD^-1, which can be ascribed to the enhancement on OH yield and direct oxidation ability by the FeOOH catalyst. Moreover, this treatment system also exhibits good reusability and can be adopted on different water background as well as different pollutants.

Roles and gains of coordination chemistry in nanofiltration membrane: A review

The nanofiltration (NF) membranes with the specific separation accuracy for molecules with the size of 0.5-2 nm have been applied in various industries. However, the traditional polymeric NF membranes still face problems like the trade-off effect, organic solvent consumption, and weak durability in harsh conditions. The participation of coordination action or metal-organic coordination compounds (MOCs) brings the membrane with uniform pores, better antifouling properties, and high hydrophilicity. Some of the aqueous-phase reactions also help to introduce a green fabrication process to NF membranes. This review critically summarizes the recent research progress in coordination chemistry relevant NF membranes. The participation of coordination chemistry was classified by the various functions in NF membranes like additives, interlayers, selective layers, coating layers, and cross-linkers. Then, the effect and mechanism of the coordination chemistry on the performance of NF membranes are discussed in depth. Perspectives are given for the further promotion that coordination chemistry can make in NF processes. This review also provides comprehensive insight and constructive guidance on high-performance NF membranes with coordination chemistry.

Preparation of Porous Ti/RuO2-IrO2@Pt, Ti/RuO2-TiO2@Pt and Ti/Y2O3-RuO2-TiO2@Pt Anodes for Efficient Electrocatalytic Decomposition of Tetracycline

Electrocatalytic oxidation (ECO) has attracted attention because of its high efficiency and environmental friendliness in water treatment. The preparation of anodes with high catalytic activity and long service lifetimes is a core part of electrocatalytic oxidation technology. Here, porous Ti/RuO₂-IrO₂@Pt, Ti/RuO₂-TiO₂@Pt, and Ti/Y₂O₃-RuO₂-TiO₂@Pt anodes were fabricated by means of modified micro-emulsion and vacuum impregnation methods with high porosity titanium plates as substrates. The scanning electron microscopy (SEM) images showed that RuO₂-IrO₂@Pt, RuO₂-TiO₂@Pt, and Y₂O₃-RuO₂-TiO₂@Pt nanoparticles were coated on the inner surface of the as-prepared anodes to form the active layer. Electrochemical analysis revealed that the high porosity substrate could result in a large electrochemically active area, and a long service life (60 h at 2 A cm^-2 current density, 1 mol L^-1 H₂SO₄ as the electrolyte, and 40 °C). The degradation experiments conducted on tetracycline hydrochloride (TC) showed that the porous Ti/Y₂O₃-RuO₂-TiO₂@Pt had the highest degradation efficiency for tetracycline, reaching 100% removal in 10 min with the lowest energy consumption of 167 kWh kg^-1 TOC. The reaction was consistent with the pseudo-primary kinetics results with a k value of 0.5480 mol L^-1 s^-1, which was 16 times higher than that of the commercial Ti/RuO₂-IrO₂ electrode. The fluorospectrophotometry studies verified that the degradation and mineralization of tetracycline were mainly ascribed to the •OH generated in the electrocatalytic oxidation process. This study thus presents a series of alternative anodes for future industrial wastewater treatment.

A review on algal biosorbents for heavy metal remediation with different adsorption isotherm models

Biosorbent composites like chitin, alginate, moss, xanthene, and cotton can be derived from biotic species such as plants, algae, fungi, and bacteria which can be used for the exclusion of both organic and inorganic toxicants from sewage, industrial effluent, polluted soils, and many more. The use of composites in place of raw substrates like alginate and chitin increases the adsorption capacity as CS₄CPL₁ beads increase the adsorption capacity for copper and nickel from 66.7 mg/g and 15.3 mg/g in the case of alginate microsphere to 719.38 mg/g and 466.07 mg/g respectively. Biosorbent fabricated from algae Chlorella vulgaris having surface area of 12.1 m²/g and pore size of 13.7 nm owing to which it displayed a higher adsorption capacity for Pb 0.433 mmol/g indicating their potential as an efficient biosorbent material. This article contains detailed information related to heavy metals as well as biosorbent that includes different isotherms, kinetics, techniques to estimate heavy metal concentration, removal methods, and adverse health effects caused due to heavy metal pollution. Apart from the above recovery and reuse of biosorbent, correlation with the sustainable development goals has also been included.

Removal of pharmaceutical and personal care products (PPCPs) by MOF-derived carbons: A review

Nowadays, the increasing demand for pharmaceuticals and personal care products (PPCPs) has resulted in the uncontrolled release of large amounts of PPCPs into the environment, which poses a great challenge to the existing wastewater treatment technologies. Therefore, novel materials for efficient treatment of PPCPs need to be developed urgently. MOF-derived carbons (MDCs), have many advantages such as high mechanical strength, excellent water stability, large specific surface area, excellent electron transfer capability, and environmental friendliness. These advantages give MDCs an excellent ability to remove PPCPs. In this review, the effects of different substances on the properties and functions of MDCs are discussed. In addition, representative applications of MDCs and composites for the removal of PPCPs in the field of adsorption and catalysis are summarized. Finally, the future challenges of MDCs and composites are foreseen.

Pre-treatment of real pharmaceutical wastewater by heterogeneous Fenton and persulfate oxidation processes

This study compares the pre-oxidation of pharmaceutical wastewater by hydroxyl radical based advanced oxidation (HR-AOP) and a sulfate radical based advanced oxidation process (SR-AOP). The heterogeneous Fenton process is chosen as a model HR-AOP and persulfate (PS) activation as a model SR-AOP. The pre-treatment efficacy of both processes in terms of TOC, and COD removals using Fe₃O₄-rGO catalyst were considered. Under the investigated experimental conditions, both processes yielded fluctuating COD values with time. The heterogeneous Fenton process discovered to be the most efficient to remove 68.7% TOC in 180 min of treatment, when Fe₃O₄-rGO: H₂O₂ = 300 mg L^-1:150 mM H₂O₂ was used at pH 3. Notably, the heterogeneous Fenton system was not considerably inhibited at the natural pH of pharmaceutical wastewater (6.75), as the process successfully removed 64.6% TOC. On the other hand, in persulfate activation studies, Fe₃O₄-rGO: PS = 400 mg L^-1: 5 mM was the ideal condition for removing 59.5% TOC in 180 min at pH 3. Whereas the natural pH condition significantly inhibited the TOC removal, as only 20.8% TOC removal was feasible. The wastewater characterisation before and after Fenton treatment reveals that Fenton oxidation leads to an increase in inorganics (chlorides: 160 ± 15 mg L^-1, nitrates: 63.14 ± 3.08 mg L^-1, sulfates: 266.31 ± 31.39 mg L^-1) necessitating an additional treatment step to reduce COD and inorganics further.

Wastewater treatment by anodic oxidation in electrochemical advanced oxidation process: Advance in mechanism, direct and indirect oxidation detection methods

Electrochemical Advanced Oxidation Process (EAOP) has been applied to the degradation of refractory pollutants in wastewater due to its strong oxidation capacity, high degradation efficiency, simple operation, and mild reaction. Among electrochemical processes, anodic oxidation (AO) is the most widely used and its mechanism is mainly divided into direct oxidation and indirect oxidation. Direct oxidation means that pollutants are oxidized at the anode by direct electron transfer. Indirect oxidation refers to the generation of active species during the electrolytic reaction, which acts on pollutants. The mechanism of AO process is controlled by many factors, including electrode type, electrocatalyst material, wastewater composition, pH, applied current and voltage levels. It is very important to explore the reaction mechanism of electrochemical treatment, which determines the efficiency of the reaction, the products of the reaction, and the extent of reaction. This paper firstly reviews the current research progress on the mechanism of AO process, and summarizes in detail the different mechanisms caused by influencing factors under common AO process. Then, strategies and methods to distinguish direct oxidation and indirect oxidation mechanisms are reviewed, such as intermediate product analysis, electrochemical test analysis, active species detection, theoretical calculation, and the limitations of these methods are analyzed. Finally some suggestions are put forward for the study of the mechanism of electrochemical advanced oxidation.

Carbon-based nanomaterial intervention and efficient removal of various contaminants from effluents - A review

Water treatment is a worldwide issue. This review aims to present current problems and future challenges in water treatments with the existing methodologies. Carbon nanotube production, characterization, and prospective uses have been the subject of considerable and rigorous research around the world. They have a large number of technical uses because of their distinct physical characteristics. Various catalyst materials are used to make carbon nanotubes. This review's primary focus is on integrated and single-treatment technologies for all kinds of drinking water resources, including ground and surface water. Inorganic non-metallic matter, heavy metals, natural organic matter, endocrine-disrupting chemicals, disinfection by-products and microbiological pollutants are among the contaminants that these treatment systems can remediate in polluted drinking water resources. Significant advances in the antibacterial and adsorption capabilities of carbon-based nanomaterials have opened up new options for excluding organic/inorganic and biological contaminants from drinking water in recent years. The advancements in multifunctional nanocomposites synthesis pave the possibility for their use in enhanced wastewater purification system design. The adsorptive and antibacterial characteristics of six main kinds of carbon nanomaterials are single-walled carbon nanotubes, multi-walled carbon nanotubes, graphene, graphene oxide, fullerene and single-walled carbon nanohorns. This review potentially addressed the essential metallic and polymeric nanocomposites, are described and compared. Barriers to use these nanoparticles in long-term water treatment are also discussed.

Fouling mechanisms in anoxic-aerobic sequencing batch membrane bioreactor based on adapted Hermia models and main foulant characteristics

Various derivatives of Hermia models (complete pore blocking, intermediate pore blocking, cake layer formation, and standard pore blocking) and different assessments of foulant characteristics have long been used to determine the membrane fouling mechanisms. Accordingly, this study aims to adapt Hermia models and their combination according to the operating conditions of an anoxic-aerobic sequencing batch membrane bioreactor (A/O-SBMBR). In addition, fouling mechanisms of the A/O-SBMBR were assessed using these models along with the main foulant characteristics. Models fitting with the transmembrane pressure (TMP) data indicated that the intermediate-standard model was accounting for the increased fouling during the whole regular operating period, with the residual sum of squares (RSS) of 58.3. A more detailed study on the distinct stages of TMP curve showed that the intermediate-standard model had the best fit in stages of 2 and 3, with the RSS equal to 2.6 and 2.8, respectively. Also, the complete-standard model provided the best description of the fouling mechanism in stage 4, with the RSS of 12.5. Different analyzes revealed how the main foulant characteristics affect the occurrence of intermediate, complete and standard fouling mechanisms in the A/O-SBMBR, which is consistent with the fitting results of the adapted Hermia models. The modeling and experimental methods used in the presented study provided a valuable basis to prevent and control membrane fouling in membrane bioreactors.

Rhodococcus: A promising genus of actinomycetes for the bioremediation of organic and inorganic contaminants

Rhodococcus is a genus of actinomycetes that has been explored by the scientific community for different purposes, especially for bioremediation uses. However, the mechanisms governing Rhodococcus-mediated bioremediation processes are far from being fully elucidated. In this sense, this work aimed to compile the recent advances in the use of Rhodococcus for the bioremediation of organic and inorganic contaminants present in different environmental compartments. We reviewed the bioremediation capacity and mechanisms of Rhodococcus spp. in the treatment of polycyclic aromatic hydrocarbons, phenolic substances, emerging contaminants, heavy metals, and dyes given their human health risks and environmental concern. Different bioremediation techniques were discussed, including experimental conditions, treatment efficiencies, mechanisms, and degradation pathways. The use of Rhodococcus strains in the bioremediation of several compounds is a promising approach due to their features, primarily the presence of appropriate enzyme systems, which result in high decontamination efficiencies; but that vary according to experimental conditions. Besides, the genus Rhodococcus contains a small number of opportunistic species and pathogens, representing an advantage from the point of view of safety. Advances in analytical detection techniques and Molecular Biology have been collaborating to improve the understanding of the mechanisms and pathways involved in bioremediation processes. In the context of using Rhodococcus spp. as bioremediation agents, there is a need for more studies that 1) evaluate the role of these actinomycetes on a pilot and field scale; 2) use genetic engineering tools and consortia with other microorganisms to improve the bioremediation efficiency; and 3) isolate new Rhodococcus strains from environments with extreme and/or contaminated conditions aiming to explore their adaptive capabilities for bioremediation purposes.

COD Reduction of Aeration Effluent by Utilizing Optimum Quantities of UV/H2O2/O3 in a Small-Scale Reactor

Extensive research has been carried out to figure out safe means of disposing various industrial effluents. Industrial wastewaters from the aeration industry such as heavy metals and oily substances contain a high degree of contamination. The advanced oxidation process is one of the most effective and rapid methods of removing contaminations, which can lead to a high chemical oxygen demand (COD). The aim of the present study is to reduce the COD of an aeration effluent with the initial COD of 13,004 mg/L. About 20 sets of experimental tests were conducted to identify the contribution of H2O2, O3, and UV to the treatment process. The influence of the quantities of additives and the dose of the UV irradiance were, too, among the subjects of the study. These factors were altered throughout the experiments and their mutual effects were measured. To design the experiments, Minitab software 16 was utilized. The experimental conditions were set at the standard values of 25 °C and 1 bar to minimize any uncertainty. Based on the results, a correlation was derived, which was capable of expressing the effects of the input parameters (AOPs parameters) on the response (the COD level). Finally, the optimization process was conducted to find the quantities of H2O2, O3, and UV irradiance required to decrease the CODs of the effluent to their lowest possible. Based on the findings, when the doses of H2O2, O3, and UV to the treatment process were 40 mg/L, 8 mg/L and 86 mWs/cm2, respectively, the COD percent change was 51.5%.

Tertiary Wastewater Treatment Technologies: A Review of Technical, Economic, and Life Cycle Aspects

The activated sludge process is the most widespread sewage treatment method. It typically consists of a pretreatment step, followed by a primary settling tank, an aerobic degradation process, and, finally, a secondary settling tank. The secondary effluent is then usually chlorinated and discharged to a water body. Tertiary treatment aims at improving the characteristics of the secondary effluent to facilitate its reuse. In this work, through a literature review of the most prominent tertiary treatment methods, a benchmarking of their technical efficiency, economic feasibility, and environmental impact was carried out. The photo-Fenton method proved to be the most technically efficient process, significantly reducing the microbial load and pharmaceutical content (by 4.9 log and 84%, respectively) of the secondary effluent. Chlorination and UV irradiation exhibited the lowest treatment costs (0.004 EUR/m−3) and the lowest global warming potential (0.04 and 0.09 kg CO2eq. m−3, respectively). After all the data were aggregated, a decision-making tool was constructed in the form of a ternary diagram, which indicates the most appropriate tertiary treatment method according to the weight-per-process aspect (technical, economic, and environmental) selected by the user, with chlorination, UV irradiation, ozonation, microalgae cultivation, and constructed wetlands prevailing in the final results.

Enrofloxacin and Sulfamethoxazole Sorption on Carbonized Leonardite: Kinetics, Isotherms, Influential Effects, and Antibacterial Activity toward S. aureus ATCC 25923

Excessive antibiotic use in veterinary applications has resulted in water contamination and potentially poses a serious threat to aquatic environments and human health. The objective of the current study was to quantify carbonized leonardite (cLND) adsorption capabilities to remove sulfamethoxazole (SMX)- and enrofloxacin (ENR)-contaminated water and to determine the microbial activity of ENR residuals on cLND following adsorption. The cLND samples prepared at 450 °C and 850 °C (cLND450 and cLND550, respectively) were evaluated for structural and physical characteristics and adsorption capabilities based on adsorption kinetics and isotherm studies. The low pyrolysis temperature of cLND resulted in a heterogeneous surface that was abundant in both hydrophobic and hydrophilic functional groups. SMX and ENR adsorption were best described using a pseudo-second-order rate expression. The SMX and ENR adsorption equilibrium data on cLND450 and cLND550 revealed their better compliance with a Langmuir isotherm than with four other models based on 2.3-fold higher values of q_mENR than q_mSMX. Under the presence of the environmental interference, the electrostatic interaction was the main contributing factor to the adsorption capability. Microbial activity experiments based on the growth of Staphylococcus aureus ATCC 25923 revealed that cLND could successfully adsorb and subsequently retain the adsorbed antibiotic on the cLND surface. This study demonstrated the potential of cLND550 as a suitable low-cost adsorbent for the highly efficient removal of antibiotics from water.

Current Progress in Natural Degradation and Enhanced Removal Techniques of Antibiotics in the Environment: A Review

Antibiotics are used extensively throughout the world and their presence in the environment has caused serious pollution. This review summarizes natural methods and enhanced technologies that have been developed for antibiotic degradation. In the natural environment, antibiotics can be degraded by photolysis, hydrolysis, and biodegradation, but the rate and extent of degradation are limited. Recently, developed enhanced techniques utilize biological, chemical, or physicochemical principles for antibiotic removal. These techniques include traditional biological methods, adsorption methods, membrane treatment, advanced oxidation processes (AOPs), constructed wetlands (CWs), microalgae treatment, and microbial electrochemical systems (such as microbial fuel cells, MFCs). These techniques have both advantages and disadvantages and, to overcome disadvantages associated with individual techniques, hybrid techniques have been developed and have shown significant potential for antibiotic removal. Hybrids include combinations of the electrochemical method with AOPs, CWs with MFCs, microalgal treatment with activated sludge, and AOPs with MFCs. Considering the complexity of antibiotic pollution and the characteristics of currently used removal technologies, it is apparent that hybrid methods are better choices for dealing with antibiotic contaminants.

Performance and mechanism of removal of antibiotics and antibiotic resistance genes from wastewater by electrochemical carbon nanotube membranes

Electrochemical carbon nanotube (CNT) and carboxylated carbon nanotube (CNT-COOH) membranes were prepared by vacuum filtration for the removal of antibiotics and antibiotic resistance genes (ARGs) from water. Scanning electron microscopy and energy-dispersive spectroscopy were used to analyze the performances of the two electrochemical membranes in the removal of antibiotics and ARGs, to determine the effects of different factors on removal rates, and to explore the mechanisms of the removal of antibiotics and ARGs. The results showed that CNT-COOH formed a porous mesh structure on the surface of polytetrafluoroethylene membrane and contained more oxygen than CNT. The electrochemical CNT-COOH membrane showed higher antibiotic and ARG removal rates than the electrochemical CNT membrane, with an antibiotics removal rate of 82% after 60 min of reaction and an ARGs concentration decrease by 1.85 log. The removal rate of antibiotics and ARGs increased with the increase in electrolyte concentration and anode voltage but decreased with the increase in the influent flow rate. The removal rate of antibiotics decreased with the increase in pH, while the best removal rates of ARGs were observed in a neutral environment. The degradation mechanism of antibiotics on the electrochemical CNT-COOH membrane was analyzed, and possible antibiotic degradation pathways were proposed. The removal of antibiotics and ARGs mainly occurred through electrochemical degradation, where hydroxyl radicals (-OH) played a dominant role.

The effect of ultrafiltration process on the fate of antibiotic-related microcontaminants, pathogenic microbes, and toxicity in urban wastewater

Ultrafiltration (UF) was assessed at chemical, microbiological, genetical and toxicological level and in terms of removing specific antibiotic-related microcontaminants from urban wastewater. The UF capacity to remove various antibiotics (clarithromycin, erythromycin, ampicillin, ofloxacin, sulfamethoxazole, trimethoprim, and tetracycline; [A₀] = 100 μg L^-1) was optimised with respect to the feed recirculation rate (25-50%) and feed/transmembrane pressure (1.5-3/1.5-2.4 bar, respectively). Here, we tested the UF capacity to reduce the cultivable bacteria (faecal coliforms, total heterotrophs, Enterococci, Pseudomonas aeruginosa), enteric opportunistic pathogens, including antibiotic-resistant bacteria (ARB) and antibiotic-resistance genes (ARGs) load. Moreover, the toxicity towards Daphnia magna and three plant species was investigated. Upon optimisation of UF, the removal of antibiotics ranged from 19% for trimethoprim to 95% for clarithromycin. The concentration of cultivable faecal coliforms in the permeate was significantly reduced compared to the feed (P < 0.001), whereas all the bacterial species decreased by more than 3 logs. A similar pattern of reduction was observed for the ARGs (P < 0.001) and enteric opportunistic pathogens (~3-4 logs reduction). A nearly complete removal of the antibiotics was obtained by UF followed by granular activated carbon adsorption (contact time: 90 min), demonstrating the positive contribution of such combination to the abatement of chemical microcontaminants.

Sulfate radical based advanced oxidation processes for agro-industrial effluents treatment: A comparative review with Fenton's peroxidation

Agro-industrial wastewater management becomes a major task while environmental regulations are becoming stricter worldwide. Agro-industrial wastewaters are known by high content of organic pollutants that cause an adverse effect on the water bodies. Industries are looking for efficient, easy-to-use and affordable treatment processes. Sulfate radical based advanced oxidation processes (S-AOPs) are arising as suitable alternatives for agro-industrial effluents treatment. In this review, the major findings regarding the application of this technology for real agro-industrial wastewater depuration are discussed. Moreover, these technologies are compared as an alternative to Fenton's process, which is a widely studied advanced oxidation process and with high efficiency in the treatment of agro-industrial effluents. The studies already carried out are promising, but there is still a great lack of studies in this area and using this technique.

Adsorption of anionic dyes from textile wastewater utilizing raw corncob

Toxic dyes are irrefutable effluent components of textile wastewater, so they have become a major economic and health concern. With the purpose of efficient removal of textile dyes, multiple nature-inspired adsorbents have been applied. Herein, raw corncob is proposed as a novel highly efficient, low-price, and abundantly attainable adsorbent with the potential for uptake of methyl red and methyl orange. Multiple experiments were carried out to optimize parameters including pH, primary concentration, adsorbent dosage, temperature, and contact time. The adsorption was raised with the mounting of the contact time and it was alleviated with the addition of initial concentration. The foremost uptake of dye was apperceived at an acidic medium pH 4 for methyl red and pH 1 for methyl orange. Scanning Electron Microscopy and Fourier Transform Infrared Spectroscopy were employed to characterize the surfaces of corncobs. The well-fitted Langmuir and Freundlich models (methyl red: R² = 0.9956 and methyl orange: R² = 0.9883) confirmed the homogeneous monolayer adsorption process on the raw corncob surface. The obtained results disclose that corncob is an effectual biosorbent for eliminating anionic dyes without the necessity for any prior modifications.

Adsorptive Removal of Naproxen from Water Using Polyhedral Oligomeric Silesquioxane (POSS) Covalent Organic Frameworks (COFs)

Covalent organic frameworks are porous crystalline compounds made up of organic material bonded together by strong reversible covalent bonds (these are novel types of materials which have the processability of extended or repeated structures with high performance, like those of thermosets and thermoplastics that produce high surface coverage). These have a long-term effect on an arrangement’s geometry and permeability. These compounds are entirely made up of light elements like H, B, C, N, O and Si. Pharmaceuticals and personal care products (PPCPs) have emerged as a new threatened species. A hazardous substance known as an “emerging toxin,” such as naproxen, is one that has been established or is generated in sufficient amounts in an environment, creating permanent damage to organisms. COF-S7, OAPS and 2-methylanthraquionone(2-MeAQ), and COF-S12, OAPS and terephthalaldehyde (TPA) were effectively synthesized by condensation (solvothermal) via a Schiff base reaction (R1R2C=NR′), with a molar ratio of 1:8 for OAPS to linker (L1 and L2), at a temperature of 125 °C and 100 °C for COF-S7 and COF-S12, respectively. The compounds obtained were assessed using several spectroscopy techniques, which revealed azomethine C=N bonds, aromatic carbon environments via solid 13C and 29Si NMR, the morphological structure and porosity, and the thermostability of these materials. The remedied effluent was investigated, and a substantial execution was noted in the removal ability of the naproxen over synthesized materials, such as 70% and 86% at a contact time of 210 min and 270 min, respectively, at a constant dose of 0.05 g and pH 7. The maximum adsorption abilities of the substances were found to be 35 mg/g and 42 mg/g. The pH result implies that there is stable exclusion with a rise in pH to 9. At pH 9, the drop significance was attained for COF-S7 with the exception of COF-S12, which was detected at pH 11, due to the negative Foster charge, consequent to the repulsion among the synthesized COFs and naproxen solution. From the isotherms acquired (Langmuir and Freundlich), the substances displayed a higher value (close to 1) of correlation coefficient (R2), which showed that the substances fit into the Freundlich isotherm (heterogenous process), and the value of heterogeneity process (n) achieved (less than 1) specifies that the adsorption is a chemical process. Analysis of the as-prepared composites revealed remarkable reusability in the elimination of naproxen by adsorption. Due to its convenience of synthesis, significant adsorption effectiveness, and remarkable reusability, the as-synthesized COFs are expected to be able to be used as potential adsorbents for eliminating AIDs from water.