Adsorption characteristics of directional cellulose nanofiber/chitosan/montmorillonite aerogel as adsorbent for wastewater treatment

Flexible cellulose nanofiber aerogel with enhanced porous structure and its applications in copper(II) removal

In order to achieve an aerogel with both rigid pore structures and desired flexibility, stiff carboxyl-functionalized cellulose nanofiber (CNFs) were introduced into a flexible polyvinyl alcohol-polyethyleneimine (PVA-PEI) crosslinking network, with 4-formylphenylboronic acid (4FPBA) bridging within the PVA-PEI network to enable dynamic boroxine and imine bond formation. The strong covalent bonds and hydrogen connections between CNF and the crosslinking network enhanced the wet stability of the aerogel while also contributed to its thermal stability. Importantly, the harmonious coordination between the stiff CNF and the flexible polymer chains not only facilitated aerogel flexibility but also enhanced its increased specific surface area by improving pore structure. Moreover, the inclusion of CNF enhanced the adsorption capacity of the aerogel, rendering it effective for removing heavy metal ions. The specific surface area and adsorption capacity for copper ions of the aerogel increased significantly with a 3 wt% addition CNF suspension, reaching 19.74 m2 g-1 and 60.28 mg g-1, respectively. These values represent a remarkable increase of 590.21 % and 213.96 %, respectively, compared to the blank aerogel. The CNF-enhanced aerogel in this study, characterized by its well-defined pore structures, and desired flexibility, demonstrates versatile applicability across multiple domains, including environmental protection, thermal insulation, electrode fabrication, and beyond.

Acid-resistant chitosan/graphene oxide adsorbent for Cu2+ removal: The role of mixed cross-linking and amino-functionalized

Copper ions in wastewater pose a significant threat to human and ecological safety. Therefore, preparing macroscopic adsorbents with reusable and high adsorption performance is paramount. This paper used graphene oxide as the adsorbent and chitosan as the thickener. Additionally, a silane coupling agent was employed to enhance the acid resistance of chitosan, and amino-modification of graphene oxide was performed. Macroscopic adsorbents with high adsorption capacity were fabricated using 3D printing technology. The results show that all five proportions of inks exhibit good printability. Dissolution experiments revealed that all materials maintained structural integrity after 180 days across pH values. Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) confirmed the successful preparation of the materials. Adsorption experiments showed that the best performing material ratio was 8 wt% graphene oxide and 7 wt% chitosan. Adsorption kinetics and isothermal adsorption experiments demonstrated that the adsorption process occurred via monolayer chemisorption. The adsorption process was attributed to strong electrostatic forces, van der Waals forces, and nitrogen/oxygen-containing functional group coordination. Cycling experiments showed that the material retained good adsorption performance after 6 cycles, suggesting its potential for practical heavy metal treatment applications.

Amino-functionalized cellulose composite for efficient simultaneous adsorption of tetracycline and copper ions: Performance, mechanism and DFT study

A novel cellulose composite (denoted as PEI@MMA-1) with porous interconnected structure was prepared by adsorbing methyl cellulose (MC) onto microcrystalline cellulose (MCC) and cross-linking polyethyleneimine (PEI) with MCC by the action of epichlorohydrin, which had the excellent adsorption property, wettability and elasticity. The performances of PEI@MMA-1 composite for removing tetracycline (TC), Cu2+ and coexistent pollutant (TC and Cu2+ mixture) were systematically explored. For single TC or Cu2+ contaminant, the maximum adsorption capacities were 75.53 and 562.23 mg/g at 30 °C, respectively, while in the dual contaminant system, they would form complexes and Cu2+ could play a "bridge" role to remarkably promote the adsorption of TC with the maximum adsorption capacities of 281.66 and 253.58 mg/g for TC and Cu2+. In addition, the adsorption kinetics, isotherms and adsorption mechanisms of single-pollutant and dual-pollutant systems have been thoroughly investigated. Theoretical calculations indicated that the amide group of TC molecule with the assistance of Cu2+ interacted with the hydroxyl group of PEI@MMA-1 composite to enhance the TC adsorption capacity. Cycle regeneration and fixed bed column experiments revealed that the PEI@MMA-1 possessed the excellent stability and utility. Current PEI@MMA-1 cellulose composite exhibited a promising application for remediation of heavy metals and antibiotics coexistence wastewater.

Surface modifications of biopolymers for removal of per- and polyfluoroalkyl substances from water: Current research and perspectives

Per- and polyfluoroalkyl substances (PFAS) are highly recalcitrant organic contaminants that have attracted ever-increasing attention from the general public, government agencies and scientific communities. To remove PFAS from water, especially the enormous volume of drinking water, stormwater, and groundwater, sorption is the most practical approach. Success of this approach demands green, renewable, and sustainable materials for capturing PFAS at ng/L or µg/L levels. To meet this demand, this manuscript critically reviewed sorbents developed from biopolymers, such as chitosan (CTN), alginate (ALG), and cellulose (CEL) covering the period from 2008 to 2023. The use of different cross-linkers for the surface modifications of biopolymers were described. The underlying removal mechanism of biosorbents for PFAS adsorption from molecular perspectives was discussed. Besides reviewing and comparing the performance of different bio-based sorbents with respect to environmental factors like pH, and sorption kinetics and capacity, strategies for modifying biosorbents for better performance were proposed. Additionally, approaches for regeneration and reuse of the biosorbents were discussed. This was followed by further discussion of challenges facing the development of biosorbents for PFAS removal.

Formulating of the sustained release of Tebuconazole pesticide using chitosan aerogel reinforced NFC/CaCO3 nanocomposite

Chitosan-based aerogels were fabricated through utilizing of nanofibrillated cellulose (NFC)/CaCO3 composites. Chitosan aerogel and extra three aerogels loaded different concentrations of NFC/CaCO3 were investigated to explore their release efficiency of Tebuconazole pesticides. Results obtained from ATR-FTIR showed a remarkable decline of the characterized chitosan hydroxyl group peak prolonging with appearance of new peaks assigned to the inclusion of inorganic calcium element. Also, SEM images showed chitosan aerogel with regular porous structure increased by incorporation with of NFC/CaCO3 nanocomposite, while EDS affirmed the presence of calcium element rather pristine chitosan aerogel. In addition to this, the physical characterizations showed significant improvement in swelling properties for aerogels incorporated NFC/CaCO3 nanocomposite at low ratios. Chitosan aerogel reinforced NFC/CaCO3 nanocomposite exhibited benefit on loading and release efficiency of Tebuconazole. All samples showed accessibility to column release method with fastest release at low slow rate 2 mL/min as giving chance for diffusion and solubility of ingredient, while release increase as heat increase as result of pore expansion. In conclusion, chitosan aerogels incorporated calcium carbonate showed better-sustained release of Tebuconazole pesticides than pristine chitosan aerogel. The produced aerogels loaded NFC/CaCO3 nanocomposite could be promising for controlled release of pesticides at water-streams in agriculture sector.

Bio-Based Aerogels for the Removal of Heavy Metal Ions and Oils from Water: Novel Solutions for Environmental Remediation

Contamination of the aqueous environment caused by the presence of heavy metal ions and oils is a growing concern that must be addressed to reduce their detrimental impact on living organisms and safeguard the environment. Recent efficient and environmentally friendly remediation methods for the treatment of water are based on third-generation bioaerogels as emerging applications for the removal of heavy metal ions and oils from aqueous systems. The peculiarities of these materials are various, considering their high specific surface area and low density, together with a highly porous three-dimensional structure and tunable surface chemistry. This review illustrates the recent progress in aerogels developed from cellulose and chitosan as emerging materials in water treatment. The potential of aerogel-based adsorbents for wastewater treatment is reported in terms of adsorption efficacy and reusability. Despite various gaps affecting the manufacturing and production costs of aerogels that actually limit their successful implementation in the market, the research progress suggests that bio-based aerogels are ready to be used in water-treatment applications in the near future.

Enhanced generation of oxysulfur radicals by the BiOBr/Montmorillonite activated sulfite system: Performance and mechanism

The easily synthesized, cost-effective, and stable photocatalysts for sulfite activation are always required for the enhancement of organic contaminants degradation. Herein, the facile coprecipitation synthesis of Bismuth oxybromide (BiOBr)/Montmorillonite (MMT) was reported, which could activate sulfite (SO32-/HSO3-) under sunlight and accelerate the catalytic performance more effectively than pristine BiOBr. After adding sulfite to the photocatalysis system, the photodegradation efficiency of atrazine (ATZ) achieved 73.7% ± 1.5% after 5 min and 94.4% ± 1.6% after 30 min of sunlight irradiation with BiOBr/MMT. The BiOBr/MMT-sulfite system also presented remarkable photocatalytic performance to eliminate various contaminants, including ciprofloxacin, sulfadiazine, tetracycline, and carbamazepine. The various features of the photocatalyst materials were studied, including their surface morphology, structure, optical properties, and composition. The results illustrated that by adding MMT, the bandgap of the pristine BiOBr was reduced and the surface area was increased, which led to an increased ability to adsorb materials. Results of various influence factors showed this enhanced system had satisfactory and stable removal performance of ATZ in the pH range of 3.0-6.5, but HPO42- had a strong negative effect on the system performance. Oxysulfur radicals (SO5·- and SO4·-), h+, and 1O2 were discovered as the prevailing active species in the BiOBr/MMT-sulfite system. The proposed degradation mechanism of this photocatalyst-enhanced system revealed that sulfite adsorption on the surface of the photocatalyst played a vital role during the initial phase, and the degradation pathway of ATZ was discussed. This study provides a new synthesis strategy of a photocatalyst for sulfite activation and expands the potential uses of Bi-based photocatalysts in degrading difficult-to-remove organic pollutants.

Magnetite nanoparticles decorated on cellulose aerogel for p-nitrophenol Fenton degradation: Effects of the active phase loading, cross-linker agent and preparation method

Magnetite nanoparticles (Fe3O4 NPs) are among the most effective Fenton-Like heterogeneous catalysts for degrading environmental contaminants. However, Fe3O4 NPs aggregate easily and have poor dispersion stability because of their magnetic properties, which seriously decrease their catalytic efficiency. In this study, a novel environmentally friendly method for synthesising Fe3O4@CA was proposed. Fe3O4 NPs were immobilized on the 3D cellulose aerogels (CAs) in order to augment the degradation efficiency of p-nitrophenol (PNP) treatment and make the separation of the catalyst accessible by vacuum filtration method. Besides, CAs were fabricated from a cellulose source extracted from water hyacinth by using different cross-linking agents, such as kymene (KM) and polyvinyl alcohol-glutaraldehyde system (PVA-GA), and other drying methods, including vacuum thermal drying and freeze drying, were evaluated in the synthesis process. As-synthesized samples were analysed by various methods, including Powder X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, energy dispersive X-ray analysis and Brunauer-Emmett-Teller. Then, using ultraviolet-visible spectroscopy, the difference in the degradability of PNP of the obtained material samples was also investigated to determine their potential applications. Results highlighted that the Fe3O4-3@CA-KF catalyst with an Fe3O4 loading of 0.40 g/gCA used KM as a cross-linker and the freeze-drying method demonstrated the highest PNP removal efficiency (92.5 %) in all Fe3O4@CA samples with a H2O2 content of 5 g/L. The degradation kinetics and well-fitted pseudo-first-order model were investigated. Notably, after five successive PNP degradation experiments, this catalyst retained ∼80 % of the ability to degrade PNP, indicating its outstanding reusability. In environmental remediation, this study provides valuable insights into the development of simply separated and high-efficiency catalysts for heterogeneous catalytic reactions.

Nanocellulose-based composite aerogels toward the environmental protection: Preparation, modification and applications

Nanocellulose aerogel has the advantages of porosity, low density and high specific surface area, which can effectively realize the adsorption and treatment of wastewater waste gas. The methods of preparing nanocellulose mainly include mechanical, chemical and biological methods. Nanocellulose is formed into nanocellulose aerogel after gelation, solvent replacement and drying processes. Based on the advantages of easy modification of nanocellulose aerogels, nanocellulose aerogels can be functionalized with conductive fillers, reinforcing fillers and other materials to give nanocellulose aerogels in electrical, mechanical and other properties. Through functionalization, the properties of nanocellulose composite aerogel such as hydrophobicity and adsorption are improved, and the aerogel is endowed with the ability of electrical conductivity and electromagnetic shielding. Through functionalization, the applicability and general applicability of nanocellulose composite aerogel in the field of environmental protection are improved. In this paper, the preparation and functional modification methods of nanocellulose aerogels are reviewed, and the application prospects of nanocellulose composite aerogels in common environmental protection fields such as dye adsorption, heavy metal ion adsorption, gas adsorption, electromagnetic shielding, and oil-water separation are specifically reviewed, and new solutions are proposed.

Green composite aerogel based on citrus peel/chitosan/bentonite for sustainable removal Cu(II) from water matrices

Here, we propose a green and sustainable 3D porous aerogel based on citrus peel (CP), chitosan (CS), and bentonite (BT). This aerogel is prepared through a simple sol-gel and freeze-drying process and is designed for efficient capture of Cu(II) ions from water matrices. CCBA-2, with its abundance of active binding sites, exhibits an impressive Cu(II) adsorption yield of 861.58 mg/g. The adsorption isotherm and kinetics follow the Freundlich and pseudo-second-order models, respectively. In the presence of coexisting mixed-metal ions, CCBA-2 demonstrates a significantly higher selectivity coefficient (KdCu = 1138.5) for removing Cu(II) ions compared to other toxic metal ions. Furthermore, the adsorption of Cu(II) ions by CCBA-2 is not significantly affected by coexisting cations/anions, ionic strength, organic matter, or different water matrices. Dynamic fixed-bed column experiments show that the adsorption capacity of Cu(II) ions reaches 377.4 mg/g, and the Yoon-Nelson model accurately describes the adsorption process and breakthrough curve. Through experiments, FTIR, and XPS analyses, we propose a reasonable binding mechanism between CCBA-2 and metal cations, involving electrostatic attraction and chemical chelation between Cu(II) and the functional groups of the aerogel. CCBA-2 saturated with Cu(II) ions can be successfully regenerated by elution with 1 M HNO3, with only a slight decrease in adsorption efficiency (5.3%) after 5 adsorption-desorption cycles. Therefore, CCBA-2 offers a cost-effective and environmentally friendly material that can be considered as a viable alternative for the green and efficient removal of toxic Cu(II) ions from wastewater.

Preparation of a Multifunctional and Multipurpose Chitosan/Cyclodextrin/MIL-68(Al) Foam Column and Examining Its Adsorption Properties for Anionic and Cationic Dyes and Sulfonamides

A multifunctional cylindrical hybrid foam column, referred to as the chitosan/cyclodextrin/MIL-68(Al) (CS/CD/MIL-68(Al)) foam column, was prepared for the first time. The prepared foam column could be used for the adsorption/removal of hydrophilic and hydrophobic contaminants by different forms. Here, it was placed in hydrophilic dye solutions to investigate the adsorption behavior of methylene blue and trypan blue. The adsorption process followed the pseudo-second-order kinetic model with R2 ranging from 0.9983 to 0.9998 for methylene blue and from 0.9993 to 1.0000 for trypan blue, and the adsorption process was consistent with the Langmuir isothermal model with R2 greater than 0.96. The RL values for methylene blue and trypan blue were 0.8871 and 0.5366, respectively, which were present between 0 and 1, indicating that the adsorption behaviors of the two dyes onto the CS/CD/MIL-68(Al) foam column were favorable. The maximum adsorption capacities (Qm) of methylene blue and trypan blue were 60.61 and 454.55 mg/g at 298 K, respectively. Also, the CS/CD/MIL-68(Al) foam column was spun into a syringe and used to adsorb trace hydrophobic sulfonamides from water in the form of filtration. The porous structure impeded the need for any external force and equipment, allowing the water sample to pass through the foam column smoothly. The conditions of the CS/CD/MIL-68(Al) foam column were optimized. The adsorption was carried out under the condition of pH = 4, the amount of the adsorbent was two foam columns, and no salt was added. It was found that the removal rate of the CS/CD/MIL-68(Al) foam column for six sulfonamides was 100%, and it could be reused at least five times. Therefore, this CS/CD/MIL-68(Al) foam column had a simple preparation method, offered a flexible and diverse form of use, was nonpolluting, biodegradable, and reusable, and could have a wider application in the field of environmental pollutant removal and adsorption.

Regenerated cellulose/chitosan composite aerogel with highly efficient adsorption for anionic dyes

A novel reusable, high-compressible cotton regenerated cellulose/chitosan composite aerogel (RC/CSCA) was prepared using N-methylmorpholine-N-oxide (NMMO) as the green cellulose solvent, and glutaraldehyde (GA) as the crosslinking agent. The regenerated cellulose obtained from cotton pulp could chemically crosslink with chitosan and GA, to form a stable 3D porous structure. The GA played an essential role in preventing shrinkage and preserving the deformation recovery ability of RC/CSCA. Due to the ultralow density (13.92 mg/cm³), thermal stability (above 300 °C), and high porosity (97.36 %), the positively charged RC/CSCA can be used as a novel biocomposite adsorbent for effective and selective removal of toxic anionic dyes from wastewater, showing an excellent adsorption capacity, environmental adaptability, and recyclability. The maximal adsorption capacity and removal efficiency of RC/CSCA for methyl orange (MO) was 742.68 mg/g and 95.83 %.

Rapid adsorption of directional cellulose nanofibers/3-glycidoxypropyltrimethoxysilane/polyethyleneimine aerogels on microplastics in water

Currently, cellulose-based aerogel materials are a hot topic owing to their high specific surface area and high porosity, as well as the green, degradable and biocompatible characteristics of cellulosic materials. Modification of cellulose to enhance the adsorption properties of cellulose-based aerogels has important research significance in solving the problem of water body pollution. In this paper, cellulose nanofibers (CNFs) were modified with polyethyleneimine (PEI), and modified aerogels with directional structures were prepared by a simple reaction and freeze-drying method. The adsorption behavior of the aerogel followed the adsorption kinetic models and isotherm models. More significantly, the aerogel could rapidly adsorb microplastics, reaching equilibrium within 20 min. Furthermore, the fluorescence displayed directly expresses the occurrence of the adsorption behavior of the aerogels. Therefore, the modified cellulose nanofiber aerogels were of reference significance for microplastic removal from water bodies.

Noval green sodium alginate/gellan gum aerogel with 3D hierarchical porous structure for highly efficient and selective removal of Congo red from water

Rational design of adsorbed materials with three-dimensional (3D) hierarchical porous structure, sustainable, high adsorption capacity, and excellent selective is of great significance in practical applications. Herein, a novel aerogel adsorbed material with 3D hierarchical porous architecture was fabricated by employing naturally abundant sodium alginate (SA)/gellan gum (GG) as basic construction blocks to achieve sustainability as well as applying polyethyleneimine (PEI) as functional material for highly efficient and selective capture of Congo red (CR). The aerogel sorbent exhibited strong microstructure, numerous active adsorption sites and being ultralight. The resulting aerogel adsorbent showed high adsorption capacity (3017.23 mg/g) toward CR, exceedingly most previously reported sorbents. Furthermore, the aerogel adsorbent was accompanied by outstanding selectivity for CR in four binary dye systems. Meanwhile, after 3 cycles, the adsorption capacity decreased by 14.8 %, but still maintained the adsorption capacity of 559.79 mg/g. Therefore, excellent adsorption performance, and superb selectivity prefigures its great prospects for wastewater purification.

Bamboo Nanocellulose/Montmorillonite Nanosheets/Polyethyleneimine Gel Adsorbent for Methylene Blue and Cu(II) Removal from Aqueous Solutions

In recent years, the scarcity of pure water resources has received a lot of attention from society because of the increasing amount of pollution from industrial waste. It is very important to use low-cost adsorbents with high-adsorption performance to reduce water pollution. In this work, a gel adsorbent with a high-adsorption performance on methylene blue (MB) and Cu(II) was prepared from bamboo nanocellulose (BCNF) (derived from waste bamboo paper) and montmorillonite nanosheet (MMTNS) cross-linked by polyethyleneimine (PEI). The resulting gel adsorbent was characterized by Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (SEM), X-ray photoelectron spectroscopic (XPS), etc. The results indicated that the MB and Cu(II) adsorption capacities of the resulting gel adsorbent increased with the solution pH, contact time, initial concentration, and temperature before equilibrium. The adsorption processes of MB and Cu(II) fitted well with the fractal-like pseudo-second-order model. The maximal adsorption capacities on MB and Cu(II) calculated by the Sips model were 361.9 and 254.6 mg/g, respectively. The removal of MB and Cu(II) from aqueous solutions mainly included electrostatic attraction, ion exchange, hydrogen bonding interaction, etc. These results suggest that the resulting gel adsorbent is an ideal material for the removal of MB and Cu(II) from aqueous solutions.

Antioxidants from Hyeronima macrocarpa Berries Loaded on Nanocellulose: Thermal and Antioxidant Stability

This study investigated the effect of different storage temperatures (35-55 °C) on the bioactive substances and antioxidant properties of Hyeronima macrocarpa berries loaded on nanocellulose. NC was extracted from banana pseudo-stems and presented an interesting surface and porosity properties. The acidified ethanol extract showed better anthocyanin extraction (1317 mg C3G eq./100 g FW) and was used for the preparation of the powdered product, which presented an intense and uniform magenta color, with CIELAB parameters of L* = 59.16, a* = 35.61, and b* = 7.08. The powder exhibited significant stability at storage temperatures of 35 and 45 °C, in which there was no significant loss of anthocyanins or a decrease in antioxidant capacity. In addition, the color was stable for up to 4 months without adding any preservative agent. The anthocyanin-rich extract of H. macrocarpa reached an estimated shelf-life of 315 days (stored at 35 °C), as a result of the impregnation process between the extract and NC, with the ability to protect the bioactives from degradation, due to NC surface properties.

Bioaerogels, the emerging technology for wastewater treatment: A comprehensive review on synthesis, properties and applications

Over the past decade use of aerogels has received much attention as an emerging technology for wastewater treatment. However, production of aerogels is not environment-friendly. Owing to its excellent properties such as porosity, three-dimensional structure, being amenable to chemical modifications, it is imperative to devise strategies for their improved production and use. Bioaerogels are non-toxic and most of their precursor compounds are biomass-derived. This review aims to present a comprehensive report on survey of existing literature published on the use of bioaerogels for removal of all major categories of water contaminants, namely, heavy metals, industrial dyes, oil, organic compounds and pharmaceuticals. It also gives critical analysis of the lacunae in the existing knowledge such as lack of studies on domestic sewage, emerging pollutants, toxicity of raw materials and adequate disposal of used adsorbents. Proposals of overcoming the limitations in the applicability of bioaerogels, like combining constructed wetlands with use of bioaerogels, among others have been discussed. In this review, emphasis has been given on production of bioaerogels, with an aim to underscore the potential of valorization of biomass waste to develop novel materials for wastewater treatment in an effort towards creating a circular and green economy.

Enhanced adsorption of copper ions from aqueous solution by two-step DTPA-modified magnetic cellulose hydrogel beads

Copper contamination of water is one of the most pressing environmental problems which has attracted extensive concern in recent decades. In this study, a series of magnetic adsorbents were synthesized by two-step modified cellulose with N-[3-(trimethoxysilyl)propyl]ethylenediamine (KH-792) and diethylenetriaminepentaacetic acid (DTPA) using for removal of Cu(II) from aqueous solutions. Adsorption performance of Cu(II) was systematically investigated under various treatment conditions as the effect of solution pH, contact time, initial concentration and temperature. The adsorption process was found to match better with the pseudo-second-order kinetics model, and the equilibrium adsorption data were well described by Langmuir model, which meant predominant governance of monolayer chemical adsorption. The analysis of FTIR and XPS confirmed the possible adsorption mechanism between Cu(II) and the synthesized adsorbents was electrostatic attraction and the chemical coordination. Compared with MCCs and APMC, DPMC showed higher adsorption capacity of Cu(II), reaching maximum adsorption capacity of 298.62 mg·g^-1 at pH 6. Given this, ease of preparation, low cost and excellent reusability, DPMC will be promising adsorbent for application in Cu(II) removal from wastewater.

Highly stable cellulose nanofiber/polyacrylamide aerogel via in-situ physical/chemical double crosslinking for highly efficient Cu(II) ions removal

Water pollution by heavy metal ions is a global concern due to detrimental effects on the ecological environment and human health. To solve the problem of the stability and recyclability of the traditional adsorbents, we proposed three-dimensional lamellar porous cellulose nanofiber/polyacrylamide composite aerogel with outstanding pollutants adsorption, easy regeneration, and multiple recycling. The aerogel adsorbent was prepared by a two-step method via facile in-situ physical/chemical double cross-linking and freeze-drying processes. The resulting aerogels showed good thermal stability, superior water stability and excellent adsorption properties, with a maximum Langmuir adsorption capacity for Cu(II) ions up to 240 mg g^-1 due to the in-situ physical/chemical combination of anionic polyacrylamide and carbonylated cellulose nanofibers. The adsorption mechanism was the electrostatic attraction, chelating effect and complex formation driving forces for the fast and efficient adsorption of Cu(II) ions. The removal efficiency of the aerogels for Cu(II) remained above 80% after 10 adsorption/regeneration cycles, suggesting its outstanding recyclability. The proposed aerogel adsorbent shows noteworthy potential for the practical treatment of heavy metal ion wastewater.

First-Principles Study on Optoelectronic Properties of Fe-Doped Montmorillonite Clay

A theoretical investigation is conducted to describe optoelectronic properties of Fe-doped montmorillonite nanoclay under spin states of low spin (LS), intermediate spin (IS), and high spin (HS). Ground state electronic properties are studied using spin-polarized density functional theory calculations. The nonradiative and radiative relaxation channels of charge carriers are studied by computing nonadiabatic couplings (NACs) using an "on-the-fly" approach from adiabatic molecular dynamics trajectories. The NACs are further processed using a reduced density matrix approach with the Redfield formalism. The computational results are presented for electronic density of states, absorption spectra, charge carrier dynamics, and photoluminescence (PL) by comparing various spin multiplicities. Results on spin α and spin β components are independent and quite different because of the partial occupation of Fe 3d states. Overall, HS is the most stable with the largest Fe-O distances. One finds different nonradiative relaxation pathways in space and on the time scale for electrons and holes. The Redfield PL reveals obvious Fe 3d-3d transitions for LS and IS.

Multifunctional Cellulose and Cellulose-Based (Nano) Composite Adsorbents

In recent years, faced with the improvement of environmental quality problems, cellulose and cellulose-based (nano) composites have attracted great attention as adsorbents. In this review article, we first report the recent progress of modification and functionalization of cellulose adsorbents. In addition, the adsorbents produced by the modification and functionalization of carboxymehyl cellulose are also introduced. Moreover, the cellulose-based (nano) composites as adsorbents are reviewed in detail. Finally, the development prospect of cellulose and cellulose-based (nano) composites is studied in the field of the environment. In this review article, a critical comment is given based on our knowledge. It is believed that these biomass adsorbents will play an increasingly important role in the field of the environment.

Chitosan functionalized with N,N-(2-aminoethyl)pyridinedicarboxamide for selective adsorption of gold ions from wastewater

The recovery of gold from wastewater has always been a research hotspot. Here, a novel chitosan-based adsorbent (CS-DPDM) was successfully synthesized by functionalizing chitosan with (N, N-(2-aminoethyl))-2,6-pyridinedicarboxamide. The adsorbent was analyzed by fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (¹H NMR), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and zeta potential method (Zeta). To investigate the adsorption performance of CS-DPDM for Au(III), the effects of pH, temperature, adsorption time and initial concentration were discussed. The maximum adsorption capacity of CS-DPDM for Au(III) at pH 5.0 is 659.02 mg/g at 318 K. The adsorption is a spontaneous endothermic behavior, and the adsorption process follows the quasi-second-order kinetic and Langmuir isotherm models, indicating that a single layer of chemical adsorption may have occurred on the surface of the adsorbent. The competitive adsorption and repetitive experiments show that CS-DPDM has considerable selectivity and reusability for Au(III). X-ray photoelectron spectroscopy (XPS) results show that N and O functional groups adsorb Au(III) on the surface of CS-DPDM through electrostatic, chelation and reduction. These results indicate that CS-DPDM has broad application prospects in recovering gold ions from aqueous solutions.

Characterization and evaluation of adsorption potential of chitosan impregnated cellulose nanofiber / multi-walled carbon nanotubes aerogel for copper ions

The development of aerogel materials with high preparation efficiency, no pollution, and high adsorption efficiency was still an effective solution for water pollution caused by heavy metal ions. This paper...

Development of Pectin-Based Aerogels with Several Excellent Properties for the Adsorption of Pb2

Traditional aerogels lack specific functional groups for the adsorption of Pb2+, which results in a low adsorption capacity and limits the application scope. Novel porous pectin-based aerogels (PPEAs) were prepared by incorporating polyethylenimine (PEI) using ethylene glycol diglycidyl ether (EGDE) as a cross-linker for the removal of Pb2+ from water. The cross-linking mechanism, morphology, mechanical strength, thermal stability, adsorption properties, and mechanism of the aerogels were investigated. The aerogels possessed several desirable features, such as a large maximum Pb2+ adsorption capacity (373.7 mg/g, tested at pH 5.0), ultralight (as low as 63.4 mg/cm3), high mechanical strength (stress above 0.24 MPa at 50% strain), and easy recyclability. Meanwhile, the equilibrium adsorption data was well described by the Langmuir-Freundlich (Sips) model and the kinetic adsorption process was well fitted using the pseudo-second-order model. The donor groups, such as -NH2, and oxygen-containing functional groups were responsible for the Pb2+ adsorption, which was confirmed by the FTIR and XPS analysis. The excellent characteristics mean that PPEAs are highly effective adsorbents in the remediation of lead-containing wastewater.

Adsorption Performance of Amino Functionalized Magnetic Molecular Sieve Adsorbent for Effective Removal of Lead Ion from Aqueous Solution

Lead ion (Pb²⁺) has high toxicity and brings great harm to human body. It is very important to find an effective method to address lead ion pollution. In this work, amino functionalized CoFe₂O₄/SBA–15 nanocomposite (NH₂–CoFe₂O₄/SBA–15) was prepared for the effective removal of Pb²⁺ from aqueous solution. The prepared NH₂–CoFe₂O₄/SBA–15 adsorbent was manifested by using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectrum (FTIR), X-ray powder diffraction (XRD), and Brunauer-Emmett-Teller (BET) analysis. In the meantime, the adsorption conditions, including pH, adsorbent dosage, and adsorption time, were studied. The investigation of adsorption kinetics revealed that the adsorption results conform to the pseudo-first-order kinetic model. The adsorption isotherms research displayed that the adsorption was consistent with the Freundlich model, demonstrating that the adsorption for Pb²⁺ with the prepared adsorbent was a multimolecular layer adsorption process. In addition, the thermodynamic investigations (ΔG < 0, ΔH > 0, ΔS > 0) demonstrated that the adsorption for Pb²⁺ with the prepared adsorbent was endothermic and spontaneous. Moreover, the prepared adsorbent showed superior anti-interference performance and reusability, implying the potential application of the adsorbent in actual water treatment. Furthermore, this research may provide a reference and basis for the study of other heavy metal ions.