Enhanced and selective adsorption of tamoxifen using sodium dodecyl sulfate modified oil-based drill cutting ash

Removal of total petroleum hydrocarbons from oil-based drilling cuttings by a heat activation persulfate-based process

Oil-based drilling cuttings (OBDC) are typical hazardous wastes generated during shale gas extraction. In this study, two persulfate-based advanced oxidation processes (AOPs), heat/PMS and heat/PDS, have been used to treat OBDC. The results showed that for the heat/PMS process, within a certain range, the oxidant dosage, temperature, and reaction time were significantly positively correlated with the degree of total petroleum hydrocarbon (TPH) removal. When these parameters were increased from their initial values to 3.57 mmol/g, 70°C, and 80 min, respectively, TPH removal rates increased significantly, by 20.95%, 18.68%, and 16.41%, respectively. However, further increases in these parameters had little effect on the TPH removal rate. Similar observations were made for the heat/PDS process. There are other differences between the two processes, including that the heat/PDS process required less oxidant to reach an effective activation state than the heat/PMS process, but required a higher temperature and a longer reaction time. Fourier-transform infrared spectrometry and gas chromatography-mass spectrometry have shown that both processes could effectively remove the light components of linear paraffins contained in OBDC. The heat/PMS process performed significantly better than the heat/PDS process in removing aromatic hydrocarbons and long-chain alkanes. Scanning electron microscopy, energy-dispersive spectrometry, and X-ray diffraction analysis implied that the elemental and mineral compositions of OBDC were not significantly modified by reaction in the heat/PMS and heat/PDS processes. This study may provide theoretical support for the technological development of heat activation and persulfate-based AOPs to remove TPH from OBDC.

Degradation of petroleum pollutants in oil-based drilling cuttings using an Fe2+-based Fenton-like advanced oxidation processes

Oil-based drilling cuttings (OBDC) contain a large amount of total petroleum hydrocarbon (TPH) pollutants, which are hazardous to the environment. In this study, Fe²⁺-activating hydrogen peroxide (Fe²⁺/H₂O₂), peroxymonosulfate (Fe²⁺/PMS), and peroxydisulfate (Fe²⁺/PDS) advanced oxidation processes (AOPs) were used to treat OBDC due to the difference in the degradation capacity of TPH caused by the type of free radical generated and effective activation conditions observed for the different oxidants studied. The results showed that the oxidant concentration, Fe²⁺ dosage, and reaction time in the three AOPs were greatly positively correlated with the TPH removal rate in a certain range. The initial pH value had a significant effect on the Fe²⁺/H₂O₂ process, and its TPH removal rate was negatively correlated in the pH range from 3 to 11. However, the Fe²⁺/PMS and Fe²⁺/PDS processes only displayed lower TPH removal rates under neutral conditions and tolerated a wider range of pH conditions. The optimal TPH removal rates observed for the Fe²⁺/H₂O₂, Fe²⁺/PMS, and Fe²⁺/PDS processes were 45.04%, 42.75%, and 44.95%, respectively. Fourier transform infrared spectrometer and gas chromatography-mass spectrometer analysis showed that the alkanes in OBDC could be effectively removed using the three processes studied, and their degradation ability toward straight-chain alkanes was in the order of Fe²⁺/PMS > Fe²⁺/PDS > Fe²⁺/H₂O₂, among which Fe²⁺/PMS exhibited the optimal removal effect for aromatic hydrocarbons. Scanning electron microscope, energy dispersive spectroscopy, and X-ray diffraction results showed no significant changes in the elemental and mineral composition of OBDC before and after treatment. Therefore, this study provided a theoretical reference for the effective degradation of TPH pollutants in OBDC.

Regional distribution, properties, treatment technologies, and resource utilization of oil-based drilling cuttings: A review

Oil-based drilling cuttings (OBDC) are hazardous wastes produced during the extensive use of oil-based drilling mud in oil and gas exploration and development. They have strong mutagenic, carcinogenic, and teratogenic effects and need to be properly disposed of to avoid damaging the natural environment. This paper reviews the recent research progress on the regional distribution, properties, treatment technologies, and resource utilization of OBDC. The advantages and disadvantages of different technologies for removing petroleum pollutants from OBDC were comprehensively analyzed, and required future developments in treatment technologies were proposed.

Enhanced adsorption of tetracycline using modified second pyrolysis oil-based drill cutting ash

In this work, second pyrolysis oil-based drill cutting ash (OBDCA-sp) was modified using NaOH and cetyltrimethylammonium bromide (CTAB), respectively. The modified OBDCA-sp was used as the novel adsorbent for adsorption of tetracycline (TC) in aqueous solutions. The original and modified OBDCA-sp were characterized by SEM, XRD, FTIR, zeta potential analysis, contact angle, and BET. The maximum theoretical adsorption quantity (45 ℃) for TC was calculated as 1.7 mg/g using CTAB-OBDCA-sp as the adsorbent. The adsorption isotherm of TC on OBDCA-sp was fitted well with Freundlich model and the adsorption kinetic was illustrated by pseudo-second-order model. Neutral condition was favorable for the adsorption of TC. The result of regeneration experiment indicated the reusability of OBDCA-sp. The hydrogen bonding was the possible mechanism for TC adsorption. This paper developed the novel surface modification methods of OBDCA-sp and provided an approach for the resource utilization of OBDCA-sp as an environmental functional material.