Treatment of textile wastewater by sulfate radical based advanced oxidation processes

Mechanistic insights of PO43- functionalized carbon nitride homojunction hydrogels in photocatalytic-self-Fenton-peroxymonosulfate system for tetracycline degradation

In this study, metal-free PO43- enriched g-C3N4/g-C3N4 (PGCN) homojunction alginate 3D beads were developed for in-situ H2O2 production under visible light. Later, the photocatalytic-self-Fenton system was integrated with peroxymonosulfate for tetracycline degradation. Initially, the PO43- enriched g-C3N4 (PCN) and a homojunction composed of PCN and g-C3N4 (GCN) were prepared via the wet-impregnation method. Later, PGCN homojunction was formulated into 3D alginate beads through the blend-crosslinking method. The comprehensive characterization of the homojunction beads affirmed the closer contact between the semiconductors, alteration of the bandgap, faster channelization of electron-hole pairs, and improved separation of charge carriers that attributed to higher catalytic efficacy. The PGCN beads exhibited a maximum H2O2 production of 535 ± 12 µM under visible light irradiation for 60 min. The homojunction hydrogels displayed 99 ± 0.25 % tetracycline degradation in 20 min in the photocatalytic-self-Fenton-PMS system. The experimental studies also claimed a maximum chemical oxygen demand removal of 81 ± 3.6 % in 20 min with maximum reusability of beads up to 20 cycles. The Z-scheme electron migration mechanism is proposed based on the results aided by scavenger and electron spin resonance analysis. Overall, the as-synthesized alginate-supported homojunction-based photocatalytic-self-Fenton-peroxymonosulfate system is highly versatile and reusable for energy and environmental remediation.

Enhanced activation of peroxymonosulfate with cobalt-doped manganese-iron oxides for contaminant degradation: Regulation of oxygen vacancy defects

Peroxymonosulfate (PMS) based on heterogeneous catalytic reaction was a promising advanced oxidation process (AOP) to remove refractory contaminants. However, the contaminant degradation efficiency was challenged by the limited number of catalytic active site and low capacity for durable electron transfer. In this study, cobalt-doped manganese-iron oxides (CoxMn1-xFe2O4) rich in oxygen vacancy (Ov) were synthesized using a microwaved hydrothermal method and applied to activate PMS for bisphenol A (BPA) degradation, which achieved the complete removal of BPA within 30 min. In all samples, Co0.5Mn0.5Fe2O4 exhibited good catalytic activity for PMS, which was approximately 21.10 times higher than that of MnFe2O4. The results of density functional theory calculations and in-situ characterization demonstrated that the enhanced performance was ascribed to the generation of Ov and the enrichment of active site, which significantly accelerated the cycling of redox pairs and improved the PMS adsorption, which was more favorable to the formation of active specie in the electron transport process. The oxidation process involved both free radical and non-radical mechanisms, with main reactive species of O2-, and 1O2 being responsible for BPA degradation. In addition, the effects of different aqueous matrices, the results of reusability experiments, and ecotoxicity assessment experiments demonstrated the viability of the Co0.5Mn0.5Fe2O4/PMS system for real sewage purification. This research revealed a structural regulation method to enhance the catalytic activity of the material and offered new perspectives on the engineering of rich Ov.

Selective removal of organic contaminants and ascorbic acid enhancement effect based on the magnetic Fe0/FeS2-doped carbon nanolayer

Developing highly effective iron-based catalyst to selectively remove organic contaminants has garnered considerable attention. Herein, a magnetic Fe0/FeS2-doped carbon nanolayer (S-Fe@NC) was synthesized through a straightforward one-step pyrolysis method, pyrolyzing a mixture composed of 4,6-dihydroxypyrimidine, trithiocyanuric acid, and FeCl3·6H2O. With the presence of PMS, S-Fe@NC demonstrated the ability to remove almost 100% bisphenol-A (50 μM) within 3 min, attributed to its excellent graphitization degree and high FeS2/Fe0 content. Furthermore, the S-Fe@NC catalyst demonstrated an impressive kobs value of 1.476 min-1, which surpassed the traditional Fenton system by 77 times and even exceeded the commercial Fe0 catalyst by 127 times. More importantly, the S-Fe@NC/PMS system succeeded in selectively removing organic contaminants based on the hydrophobic interaction between catalyst and contaminants. Besides, the result of electron paramagnetic resonance and the radical quenching experiments indicated that ·OH, SO4·-, 1O2, and O2·- were involved in the organic contaminants removal. Interestingly, after adding ascorbic acid (AA) to the S-Fe@NC/PMS system, more ROS could be generated to result in the kobs augmenting by 4.16 times (6.133 min-1), completely different from the common sense that AA was usually used as a radical quencher. Additionally, the magnetically separable catalyst also exhibited excellent reusability and broad pH adaptability (2.0-12.0). This study provided a valuable insight for developing highly selective and effective Fe-based catalyst for practical wastewater treatment.

Potential of metallurgical iron-containing solid waste-based catalysts as activator of persulfate for organic pollutants degradation

The production of solid wastes in the metallurgical industry has significant implications for land resources and environmental pollution. To address this issue, it is crucial to explore the potential of recycling these solid wastes to reduce land occupation while protecting the environment and promoting resource utilization. Steel slag, red mud, copper slag and steel picking waste liquor are examples of solid wastes generated during the metallurgical process that possess high iron content and Fe species, making them excellent catalysts for persulfate-based advanced oxidation processes (PS-AOPs). This review elucidates the catalytic mechanisms and pathways of Fe2+ and Fe0 in the activation PS. Additionally, it underscores the potential of metallurgical iron-containing solid waste (MISW) as a catalyst for PS activation, offering a viable strategy for its high-value utilization. Lastly, the article provides an outlook towards future challenges and prospects for MISW in PS activation for the degradation of organic pollutants.

Role of biochar in superoxide-dominated dye degradation in catalyst-activated peroxymonosulphate process

In recent times, the application of biochar (BC) as an upcoming catalyst for the elimination of recalcitrant pollutants has been widely explored. Here, an iron loaded bamboo biochar activated peroxymonosulphate (PMS) process was tested for removing Congo red (CR) dye from water medium. The catalyst was synthesized using a green synthesis method using neem extracts and characterized using SEM, FTIR, and XRD. The effects of various operating parameters, including solution pH, catalyst dosage, and pollutant dosage, on dye degradation efficiency were examined. The results showed that at the optimized conditions of 300 mg L-1 PMS concentration, 200 mg L-1 catalyst dosage, and pH 6, about 89.7% of CR dye (initial concentration 10 ppm) was removed at 60 min of operation. Scavenging experiments revealed the significant contribution of O2•-, •OH, and 1O2 for dye degradation, with a major contribution of O2•-. The activation of PMS was mainly done by biochar rather than iron (loaded on biochar). The catalyst was highly active even after four cycles.

Advancements in application of modified biochar as a green and low-cost adsorbent for wastewater remediation from organic dyes

Synthetic organic dyes, which are resistant to biodegradation, pose a notable health risk, potentially leading to cancer and respiratory infections. Researchers have addressed this concern by exploring physicochemical methods to remove organic dyes from wastewater. A particularly promising solution involves modified biochar adsorbents, which demonstrate high efficiency in organic dye removal. Biochar, a charcoal-like material derived from biomass pyrolysis, offers advantages such as low cost, eco-friendliness, high efficiency and reusability. Beyond its role in sustainable soil remediation, biochar proves effective in removing organic dyes from wastewater after undergoing physical or chemical modification. Acid-base activation or metal-heteroatom impregnation enhances biochar's adsorption capacity. This comprehensive review examines the attributes of biochar, common methods for production and modification, and the impacts of raw materials, pyrolysis temperature, heating rate and residence time. It further elucidates the biochar adsorption mechanism in the removal of organic dyes, assessing factors influencing efficiency, including biochar feedstock, solution pH, adsorption temperature, particle size, initial dye concentration, biochar dosage and reaction time. It explores challenges, opportunities, reusability and regeneration methods of biochar in treating organic dye wastewater. It also discusses recent advances in organic dye removal using adsorption-based biochar. The review ultimately advocates for enhancing biochar's adsorption performance through post-modification.

In situ synthesis of oxygen-doped carbon quantum dots embedded in MIL-53(Fe) for efficient degradation of oxytetracycline

Introducing carbon quantum dots (CQDs) into photocatalysts is believed to boost the charge transfer rate and reduce charge complexation. Doping heteroatoms such as N, S, or P enable CQDs to have an uplifting electron transfer capability. However, the application of oxygen-doped CQDs to improve the performance of photocatalysts has rarely been reported. Herein, a type of carbon-oxygen quantum dots (COQDs) was in situ embedded into MIL-53(Fe) to aid peroxydisulfate (PDS)-activated degradation of oxytetracycline (OTC) under visible light irradiation. The successful embedding of COQDs was confirmed by XRD, FT-IR, XPS, SEM, and TEM techniques. Photoelectrochemical testing confirmed its better performance. The prepared COQDs1/MIL-53(Fe) showed 88.2% decomposition efficiency of OTC in 60 min, which was 1.45 times higher than that of pure MIL-53(Fe). In addition, the performance of the material was tested at different pH, OTC concentrations, catalyst dosing, and PDS dosing. It was also subjected to cyclic testing to check stability. Moreover, free radical trapping experiments and electron paramagnetic resonance were conducted to explore the possible OTC deterioration mechanism. Our work provides a new idea for the development of MOFs for water treatment and remediation.

Decomposition of metal-organic complexes and metal recovery in wastewater: A systematic review and meta-synthesis

Metals are rarely found as free ions in natural and anthropogenic environments, but they are often associated with organic matter and minerals. Under the context of circular economy, metals should be recycled, yet they are difficult to extract for their complex forms in real situations. Based on the protocols of review methodology and the analysis of VOS viewer, there are few reviews on the properties of metal-organic complexes, decomplexation methods, the effect of coexisting ions, the pH influence, and metal recovery methods for the increasingly complicated metal-organic complexes wastewater. Conventional treatment methods such as flocculation, adsorption, biological degradation, and ion exchange fail to decompose metal-organic complexes completely without causing secondary pollution in wastewater. To enhance comprehension of the behavior and morphology exhibited by metal-organic complexes within aqueous solutions, we presented the molecular structure and properties of metal-organic complexes, the decomplexation mechanisms that encompassed both radical and non-radical oxidizing species, including hydroxyl radical (OH), sulfate radical (SO˙4-), superoxide radical (O˙2-), hydrogen peroxide (H2O2), ozone (O3), and singlet oxygen (1O2). More importantly, we reviewed novel aspects that have not been covered by previous reviews considering the impact of operational parameters and coexisting ions. Finally, the potential avenues and challenges were proposed for future research.

Synthesis, characterization, and application of Cu-substituted LaNiO3 perovskites as photocatalysts and/or catalysts for persulfate activation towards pollutant removal

The presence of emerging contaminants in environmental aqueous matrices is an ever-growing problem, since conventional wastewater treatment methods fail to adequately remove them. Therefore, the application of non-conventional methodologies such as advanced oxidation processes is of great importance to tackle this modern problem. Photocatalysis as well as catalytic activation of persulfates are promising techniques in this field as they are capable of eliminating various emerging contaminants, and current research aims to develop new materials that can be utilized for both processes. In this light, the present study focused on the use of a simple sol-gel-combustion methodology to synthesize Cu-substituted LaNiO3 perovskite materials in an attempt to improve the photocatalytic and catalytic performance of pure LaNiO3, using molar ratios of Cu:Ni that have not been previously reported in the literature. The morphological, structural, and optical features of the synthesized materials were characterized by a series of analytical techniques (e.g., X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, diffuse reflectance spectroscopy, etc.). Also, their performance as photocatalysts, persulfate anion activators and simultaneously as photocatalysts/persulfate anion activators (hybrid) was evaluated by conducting laboratory-scale experiments using phenol (phenolics) as a model emerging contaminant. Interestingly, the results revealed that LaCu0.25Ni0.75O3 exhibited the best efficiency in all the applied processes, which was mainly attributed to the introduction of oxygen vacancies in the structure of the substituted material. The contribution of selected reactive species in the hybrid photocatalytic/catalytic experiments utilizing LaCu0.25Ni0.75O3 as a (photo)catalyst was investigated using appropriate scavengers, and the results suggested that singlet oxygen is the most dominant. Additionally, the stability of all synthesized perovskites was assessed by monitoring the concentration of the leached Cu and/or Ni cations at the end of every applied process. Finally, the reusability of LaCu0.25Ni0.75O3 was evaluated in three consecutive catalytic cycles using the hybrid experiment methodology, as this process demonstrated the best efficiency in terms of phenolics removal, and the results were rather promising.

Novel Magnetic MnFe2O4-Decorated Graphite-Like Porous Biochar as a Heterogeneous Catalyst for Activation of Peroxydisulfate Toward Degradation of Rhodamine B

A magnetic MnFe2O4-modified graphite-like porous biochar composite (MnFe2O4/KFS800) was synthesized by the hydrothermal method, and its catalytic activity was evaluated in the activation of peroxydisulfate toward degradation of Rhodamine B. After characterization by SEM, XRD, and the BET method, the specific surface area and total pore volume of the MnFe2O4/KFS800 catalyst reached 121 m2/g and 0.263 m3/g, and exhibited plate-like morphology with good crystallinity. The degradation rate of Rhodamine B by the obtained composite was more than 91.1% when the initial concentration of RhB was 10 mg/L, the dosage of MnFe2O4/KFS800 was 0.2 g/L, and the initial pH was 6.7. Then the anti-interference ability of the obtained composite was studied, and it was found that there was a little effect on the degradation of Rhodamine B with the presence of humic acid. Finally, quenching test, EPR research, and XPS analysis were conducted to reveal the catalytic mechanism, and possible mechanism was a synergistic behavior of free radicals (SO4•-, •OH, O2•-) and nonfree radicals (1O2), and trace amounts of uncarbonized bagasse was also involved in the formation of free radicals.

Isolating micro/nanoplastics from organic-rich wastewater: Co/PMS outweighs Fenton system

Rapid isolation of microplastics is the prerequisite for correct and in-depth understanding of their environmental impacts and human health threats. And Fenton's reagent (Fe/H2O2 system, FHS) has been proven to be a viable way to isolate microplastics from wastewater, but it is limited because of harsh reaction conditions, long reaction time and low efficiency. Herein, it's proven that the Fenton-like system, which is using Cobalt (II) salts to decompose potassium peroxymonosulfate (Co/PMS system, CPS) with generation of 1O2, can offer shorter time (within 30 min) in complex sample isolation. The experimental results showed that the isolation time of micro/nanoplastics from pollutants with CPS in only 30 min, while it was at least more than 5 h with FHS. Via a serious of experiments of comparison and characterization between FHS and CPS, whether from the point of view of reaction time or isolation effect, CPS is superior to FHS. On this basis, we validate the applicability of this system (CPS) in different reaction conditions (concentration, pH), different sizes (from microns to nanometers) and types of plastic (PS, PA, PE, PP, PVC). In addition, the CPS can also preserve the integrity of the plastic itself and reduce the impact on the quality of samples evidenced by a variety of characterization of physicochemical structure like UV-vis, TEM, AFM, FTIR and XPS. CPS is proved to be faster, higher, stronger for enhancing the isolation of micro/nanoplastics from complex matrix. In a word, this study provides a promising solution for the efficient isolation of microplastics from wastewater without causing additional harm to the plastics.

Comparative study of Fe2+/H2O2 and Fe2+/persulfate systems on the pre-treatment process of real pharmaceutical wastewater

Advanced oxidation technologies based on hydroxyl radical (•OH) and sulfate radical (SO4-•) are two common types of advanced oxidation technologies, but there are not many reports on the application of advanced oxidation methods in actual wastewater pretreatment. This article compares the pre-treatment performance of Fe2+/H2O2 and Fe2+/Persulfate systems in actual pharmaceutical wastewater, and combines EEM, GC-MS, and toxicity testing results to explore the differences in TOC, COD, and NH3-N removal rates, optimal catalyst dosage, applicable pH range, toxicity of effluent after reaction, and pollutant structure between the two systems. The results indicate that the Fe2+/H2O2 system has a higher pollutant removal rate (TOC: 71.9%, COD: 66.9%, NH3-N: 34.1%), but also requires a higher catalyst (Fe2+) concentration (6.0 g/L), and its effluent exhibits characteristic peaks of aromatic proteins. The Fe2+/Persulfate system has a wider pH range (pH ≈ 3-7) and is more advantageous in treating wastewater containing more cyclic organic compounds, but the effluent contains some sulfur-containing compounds. In addition, toxicity tests have shown that the toxicity reduction effect of the Fe2+/Persulfate system is stronger than that of the Fe2+/H2O2 system.

Mechanistic investigation of the electricity and gallic acid synergistically accelerated Fe(III)/Fe(II) cycle for the degradation of carbamazepine

This study investigated the application of a natural plant polyphenol, gallic acid (GA) to form complex with iron to promote the redox cycle of Fe(III)/Fe(II) under neutral initial pH conditions in the electrochemical (EC) system for activation of peroxymonosulfate (PMS) to efficiently degrade carbamazepine (CBZ). Results demonstrated that the synergistic effects of GA and EC significantly improved the removal efficiency, and the EC/GA/Fe(III)/PMS system effectively removed 100% of CBZ within a wide initial pH range of 3.0-7.0. The optimum stoichiometric ratio of GA to Fe(III) was found as 2:1. Investigations including quenching experiment, chemical probe analysis, and electron paramagnetic resonance (EPR) analysis were conducted to identify the primary reaction radicals as •OH, SO4•-, along with the 1O2 and Fe(IV). In the EC/GA/Fe(III)/PMS system, the synergistic effect of GA and electrochemistry led to a remarkable enhancement in the generation of •OH. Furthermore, the complexation reduction mechanism of GA and Fe(III) was proposed based on experimental and instrumental analyses, which demonstrated that the semi-quinone products of GA were the main substances promoting the Fe(III)/Fe(II) cycle. Mass spectrometry results showed that CBZ generated 27 byproducts during degradation, with formic acid as the main product of GA. The degradation efficiency of the EC/GA/Fe(III)/PMS system remained stable and excellent, exhibiting remarkable performance in the presence of various inorganic anions, including Cl- and NO3-, as well as naturally occurring organic compounds such as fulvic acid (FA). Overall results indicated that the EC/GA/Fe(III)/PMS system can be applied to effectively treat practical wastewater treatment without requirement of pH adjustment.

PMS coupled Mn(II) mediated electrochemistry processes (E-Mn(II)-PMS) on the efficient RB19 wastewater treatment: Focus on the regulation and reinforcement of Mn(III)/Mn(II)

Dye wastewater, represented by reactive blue 19 (RB19), severely threatens the aquatic ecological environment and human health, such that an efficient RB19 wastewater treatment technology should be urgently developed. Based on manganese ion-mediated electrochemistry, PMS was introduced to develop a novel electrocatalytic system (E-Mn(II)-PMS) that can efficiently remove and degrade RB19. The synergistic effect between E, Mn(II), and PMS was verified in this study through comparative experiments of a wide variety of systems. The removal efficiency of RB19 reached 95.1% in 50 min under reasonable power consumption (3.29 kWh/m3). Moreover, the effects exerted by different operating conditions (e.g., initial pH, current density, RB19 concentration, Mn(II) concentration, as well as PMS concentration) and water matrix on the degradation efficiency of RB19 were explored through single factor experiments. The active oxidation species (ROS) and their contribution rate for the degrading and removing RB19 were studied through quenching experiments, EPR experiments, TMT-15 metal capture experiments, as well as PP complexation experiments. The role played by non-free radicals took on critical significance in the oxidation removal of RB19, which comprised direct electro oxidation, Mn(III) oxidation, and 1O2 oxidation. The enhancement effect of free radicals (SO4·- and HO∙) was not sufficiently significant, with a low degree of contribution. The oxidation effect of the anode facilitated the conversion of Mn (II) to Mn (III), which was employed in PMS for expediting the production of 1O2. The reduction effect of the cathode blocked the production of Mn (IV) as a side reaction, such that the continuous circulation of manganese ions between divalent and trivalent was promoted. Meanwhile, the cathode reacted with PMS to generate a small part of SO4·- and HO∙. In addition, the reaction active site of RB19 was predicted, and a possible degradation pathway was proposed in accordance with the mass spectrometry results and the DFT calculation. As revealed by the results of the QSAR analysis and the plant culture experiments, the biological toxicity of RB19 was markedly reduced after the sample was administrated with E-Mn(II)-PMS. E-Mn(II)-PMS-mediated electrochemical technology displays several advantages (e.g., high efficiency, low consumption, recyclability, wide pH window, and strong applicability) while showing promising market development and utilization for treating dye wastewater.

High-efficient removal of anionic dye from aqueous solution using metal-organic frameworks@chitosan aerogel rich in benzene structure

With the exponentially increase of dye pollutants, the purification of dye wastewater has been an urgent ecological problem. As a novel type of porous adsorbent, metal-organic frameworks still face challenges in recyclability, agglomeration, and environmentally unfriendly synthesis. Herein, MOF-525 was in-situ growth onto the surface of the chitosan (CS) beads to fabricate MOF-525@CS aerogel. CS was utilized as substrate to uniformly disperse MOF-525, thereby significantly mitigating agglomeration and improving recyclability of MOF-525. The characterization results shown that MOF-525@CS aerogel had a high specific surface area of 103.0 m2·g-1, and MOF-525 was uniformly distributed in the 3D porous structure of CS, and the presence of benzoic acid was detected. The MOF-525@CS aerogel had a remarkable adsorption capacity of 1947 mg·g-1 for Congo red, which is greater than the sum of its parts. MOF-525@CS aerogel also inherited the rapid adsorption ability of MOF-525, removing 80 % of Congo red within 600 min. Such excellent adsorption performance can be attributed to the benzoic acid trapped by CS via CN band to enhance the π-π stacking interactions. Additionally, the utilization of benzoic acid makes the synthesis process of MOF-525@CS aerogel more environmentally friendly. The high-efficient MOF-525@CS aerogel is a competitive candidate for dye pollution adsorption.

Iron-loading N and S heteroatom doped porous carbon derived from chitosan and CdS-Tetrahymena thermophila for peroxymonosulfate activation

Transforming waste into resources is an important strategy to enhance the economic efficiency and reduce the waste entering the environment. In this work, iron-loading N and S co-doped porous carbon materials, as peroxymonosulfate (PMS) activator for pollutants degradation, were prepared by pyrolysis of the mixture of iron loading chitosan and CdS-Tetrahymena thermophila under N2 flow. Chitosan is mainly derived from the shell waste of shrimp and crab, and CdS-Tetrahymena thermophila is produced in the removing process of Cd2+ pollution bioremediation using Tetrahymena thermophila. The synergistic effects of iron related species and heteroatoms (S/N) co-doped porous carbon in the obtained carbon materials improved the performance for activating PMS. The prepared Fe-S-CS-1-900 exhibited high performance for the degradation of Rhodamine B (RhB) by activating PMS. Radical quenching tests and electron paramagnetic resonance measurements suggested that superoxide radical (O2-) and singlet oxygen (1O2) were the primary reactive oxygen species in RhB degradation. These results propose new insights of using biomass waste to derive Fe-loading N and S heteroatom co-doping carbon as PMS activator applied in the removal of organic pollutants.

Removal of oxytetracycline from water by S-doped MIL-53(Fe): Synergistic effect of surface adsorption and persulfate activation

In this study, a novel catalyst based on MIL-53(Fe) was synthesized and modified through sublimed sulfur (S-MIL-53(Fe)) to induce a synergistic effect of surface adsorption and persulfate activation. The S-doped modification not only increased the surface area but also accelerated the electron transfer process of the iron cycle. The performance of the newly synthesized S-MIL-53(Fe) adsorptive catalyst was evaluated by chemical adsorption and peroxydisulfate (PDS) activated removal of an emerging pollutants, oxytetracycline (OTC). The S-MIL-53(Fe) adsorptive catalyst was able to adsorb 61.7% of OTC after 120 min, and the removal efficiency reached 84.8% within 5 min after PDS dosing. The boosting effect of sulfur on the system was confirmed by characterization analysis and experimental testing. Even after 7 cycles, the removal efficiency of S-MIL-53(Fe) (69.0%) for OTC remained superior to that of pure MIL-53(Fe) (25.1%). Additionally, the adsorption kinetics and adsorption isotherm model of the material were investigated. The possible OTC degrading process was proposed based on radical quenching and electron paramagnetic resonance (EPR). This study provides a feasible way to fabricate an S-doped MIL-53(Fe) adsorptive catalyst for the remediation of antibiotics-containing wastewater.

Treatment of textile wastewater using the Co(II)/NaHCO3/H2O2 oxidation system

Textile wastewater (TWW) is one of the most hazardous wastewaters for ecosystems when it is discharged directly into water streams without adequate treatment. Some organic pollutants, such as dyes in TWW, are considered refractory compounds that are difficult to degrade using conventional chemical and biological methods. The bicarbonate-activated peroxide (BAP) system is an advanced oxidation process (AOP) based on applying H2O2, which has been demonstrated to be a clean and efficient technology for dye degradation, with the advantage of operating under slightly alkaline pH conditions. In this study, response surface methodology (RSM) based on a central composite design (CCD) was used to optimize the degradation of TWW contaminated with the azo dye Acid Black 194 using the BAP system catalyzed with cobalt ions in solution (Co2+). The analysis of variance (ANOVA) technique was applied to identify significant variables and their individual and interactive effects on the degradation of TWW. The optimum reagent concentrations for degrading TWW at 25 °C and with 45 μM Co2+ were 787.61 and 183.34 mM for H2O2 and NaHCO3, respectively. Under these conditions, complete decolorization (≥99.40), 32.20 % mineralization, and 52.02 % chemical oxygen demand removal were achieved. Additionally, the acute toxicity of textile wastewater before and after oxidation was evaluated with guppy fish (Poecilia reticulata), showing a total reduction in mortality after treatment with the Co2+-BAP system. The Co2+-BAP oxidation system is a potential method for textile wastewater treatment, which, in addition to achieving complete decolorization and partial mineralization, improves biodegradability and reduces the toxicity of the treated water.

B4C/Ce co-modified Ti/PbO2 dimensionally stable anode: Facile one-step electrodeposition preparation and highly efficient electrocatalytic degradation of tetracycline

The application of PbO2 for electrochemical oxidation technology is limited by its low electrocatalytic activity and short service life. Herein, based on the facile one-step electrodeposition, we prepared a boron carbide (B4C) and cerium (Ce) co-modified Ti/PbO2 (Ti/PbO2-B4C-Ce) electrode to overcome these shortcomings. Compared with Ti/PbO2 electrode, the denser surface is displayed by Ti/PbO2-B4C-Ce electrode. Meanwhile, electrochemical characterization indicates that the introduction of B4C and Ce significantly enhance the electrochemical performance of PbO2 electrode. In degradation experiments, under optimized conditions (current density 20 mA cm-2, pH 9, 0.15 M Na2SO4 and 30 °C), the fully degradation of tetracycline (TC) can be completed within 30 min. Furthermore, the trapping experiment demonstrates that ∙OH and SO4·- radicals have a synergistic effect in the degradation process of TC. Based on results of liquid chromatography-mass spectrometer, the generated ·OH preferentially attacks amides, phenols and conjugated double bond groups in TC. Importantly, Ti/PbO2-B4C-Ce electrode maintains a constant degradation efficiency even after 10 recycling tests, and its service life is 2.4 times of traditional Ti/PbO2 electrode. Hence, Ti/PbO2-B4C-Ce electrode is a promising electrode for degradation of organic wastewater containing amides, phenols, and conjugated double bond groups.

Straw-derived biochar for the removal of antibiotics from water: Adsorption and degradation mechanisms, recent advancements and challenges

Antibiotics, a kind of containments with the properties of widely distributed and difficult to degrade, has aroused extensive attention in the world. As a prevalent agricultural waste, straws can be utilized to prepare biochar (straw-derived biochar, SBC) to remove antibiotics from aquatic environment. To date, although a number of review papers have summarized and discussed research on biochar application in wastewater treatment and soil remediation, there are few reviews on SBC for antibiotic removal. Due to the limitations of poor adsorption and degradation performance of the pristine SBC, it is necessary to modify SBC to improve its applications for antibiotics removal. The maximum antibiotic removal capacity of modified SBC could reach 1346.55 mg/g. Moreover, the adsorption mechanisms between modified SBC and antibiotics mainly involve π-π interactions, electrostatic interactions, hydrophobic interactions, and charge dipole interactions. In addition, the modified SBC could completely degrade antibiotics within 6 min by activating oxidants, such as PS, PDS, H2O2, and O3. The mechanisms of antibiotic degradation by SBC activated oxidants mainly include free radicals (including SO4•-, •OH, and O2•-) and non-free radical pathway (such as, 1O2, electrons transfer, and surface-confined reaction). Although SBC and modified SBC have demonstrated excellent performance in removing antibiotics, they still face some challenges in practical applications, such as poor stability, high cost, and difficulties in recycling. Therefore, the further research directions and trends for the development of SBC and biochar-based materials should be taken into consideration.

Prussian blue analogues-derived zero valent iron to efficiently activate peroxymonosulfate for phenol degradation triggered via reactive oxygen species and high-valent iron-oxo complexes

It is of great significance to develop the effective technique to treat phenol-containing wastewater. Herein, Fe-based prussian blue analogues-derived zero valent iron (ZVI) was successfully synthesized by one-step calcination method. Owing to high specific surface area and rich active sites, ZVI-2 possessed excellent performance in charge transfer. Notably, in comparison with conventional ZVI and Fe2+, ZVI-2 can effectively activate peroxymonosulfate (PMS) for achieving rapid degradation of phenol, and the highest removal efficiency of phenol reached 94.9% within 24 min. More importantly, developed ZVI-2/PMS oxidation system with good stability displayed strong anti-interference capability. Interestingly, Fe0 loaded on the surface of ZVI-2 can efficiently break the O-O bond of PMS to generate reactive oxygen species (i.e., SO4•-, OH•, O2•- and 1O2). As main adsorption sites of PMS, the existence of oxygen vacancy promote the formation of high-valent transition metal complexes (namely ZVI-2≡Fe4+=O). Under the combined action of reactive oxygen species and ZVI-2≡Fe4+=O, phenol can be eventually degraded into CO2 and H2O. The possible degradation pathways of phenol were also investigated. Furthermore, proposed ZVI-2/PMS oxidation system displayed great potential for application in the field of wastewater treatment. All in all, current work provided a valuable reference for design and application of Fe-based catalysts in PS-AOPs.

Z-scheme MnO2/Mn3O4 heterojunctions with efficient peroxymonosulfate activation for organic pollutant removal

The exploration of efficient heterogeneous catalysts for persistent organic pollutant removal is extremely attractive. In the present work, MnO2/Mn3O4 photo-Fenton catalysts were designed by a facile hydrothermal route to activate peroxymonosulfate (PMS) under visible light irradiation for organic pollutant degradation. The optimized MnO2/Mn3O4 heterojunction shows excellent Rhodamine B (RhB) removal efficiency, whose apparent kinetic constant is 11.9 and 5.36 times as high as the MnO2 and Mn3O4. Meanwhile, there is a neglectable attenuation in catalytic performance after 5 recycling runs. Based on the active species trapping experiments, the non-radical process contributes more than the radical process during RhB degradation. Moreover, factors including the dosage of PMS, initial RhB concentration, initial pH, the presence of various anions, different organic pollutants, and water sources are investigated. Systematical characterizations reveal that the enlarged specific surface areas and the efficient charge separation aroused from the Z-scheme mechanism are attributed to the enhanced photo-Fenton performance. The present work contributes to the construction of the Mn-based photo-Fenton catalyst with efficient PMS activation capacity for environmental remediation.

Pineapple wastewater as co-substrate in treating real alkaline, non-biodegradable textile wastewater using biogranulation technology

This study was to develop biogranules using a sequencing batch reactor (SBR) and to evaluate the effect of pineapple wastewater (PW) as a co-substrate for treating real textile wastewater (RTW). The biogranular system cycle was 24 h (2 stages of phase), with an anaerobic phase (17.8 h) followed by an aerobic phase (5.8 h) for every stage of the phase. The concentration of pineapple wastewater was the main factor studied in influencing COD and color removal efficiency. Pineapple wastewater with different concentrations (7, 5, 4, 3, and 0% v/v) makes a total volume of 3 L and causes the OLRs to vary from 2.90 to 0.23 kg COD/m3day. The system achieved 55% of average color removal and 88% of average COD removal at 7%v/v PW concentration during treatment. With the addition of PW, the removal increased significantly. The experiment on the treatment of RTW without any added nutrients proved the importance of co-substrate in dye degradation.

Combination of electrochemically activated persulfate process and electro-coagulation for the treatment of municipal landfill leachate with low biodegradability

To handle complex wastewater with limited biodegradability, hybrid treatment systems are necessary. The current study represents the combined effectiveness of sulfate-radical associated electro-chemical advanced oxidation process (SR-EAOP) and electro-coagulation (EC) for the treatment of stabilized landfill leachate. For SR-EAOP, Pt/Ti was employed as the anode and an iron plate as the cathode; while EC treatment was performed by switching the polarity. Hence, both electrochemical treatment was carried out in single reactor. Initially, the effects of pH, applied voltage, persulfate and Fe2+ dosage, on the performance of SR-EAOP was examined. Sulfate radical was generated in the electrolytic system via cathodic reduction of persulfate (PS) and ferrous (Fe2+) ion activation. Auxiliary processes such as anodic oxidation via Pt/Ti anode and indirect electro-chemical oxidation were also contributed for pollutant degradation. Combined process SR-EAOP followed by EC (SR-EAOP + EC) has better leachate treatment efficacy in comparison with EC + SR-EAOPs. The SR-EAOP + EC based combined treatment mechanism achieved an efficient COD reduction of 88.67% than that of EC + SR - EAOP process (74.51% COD reduction). Characterization studies have been carried out for post-treated dried-sludge using Field Emission scanning electron microscope (FE-SEM) and X-ray powder diffraction (XRD) techniques. The combined process treatment (SR-EAOP + EC) can be applied as pre-treatment for leachate decontamination.

Adsorptive removal of acid blue dye 113 using three agricultural waste biomasses: The possibility of valorization by activation and carbonization - A comparative analysis

The presence of various organic and inorganic contaminants in wastewater leads to serious health effects on humans and ecosystems. Industrial effluents have been considered as noticeable sources of contaminating water streams. These effluents directly liberate the pollutants such as dye molecules and heavy metal ions into the environment. In the present study, three biowaste materials (groundnut shell powder, coconut coir powder and activated corn leaf carbon) were utilized and compared for the removal of acid blue dye 113 from aqueous solutions. The characterization study of newly prepared sorbent material (H3PO4-activated corn leaf carbon) and the other utilized sorbents was carried out by Scanning Electron Microscope (SEM) and Fourier Transform Infrared Spectrophotometer (FTIR), along with Energy Dispersive X-Ray (EDX) Analysis. The influence of experimental conditions such as pH, initial dye concentration, temperature, contact time, and sorbent dosage on the removal efficiency of the dye were appraised. The adsorption isotherm and kinetic result of acid blue dye 113 adsorption onto the sorbents best obeyed from Sips and pseudo-second-order kinetic model. Overall, the outcomes confirmed that the newly synthesized sorbent material (carbonized H3PO4-activated corn leaf) has superior adsorption capacity, rapid adsorption, and higher suitability for the removal of toxic dyes from the contaminated waters.

Removal of chemical oxygen demand and ammonia nitrogen from high salinity tungsten smelting wastewater by one-step electrochemical oxidation: From bench-scale test, pilot-scale test, to industrial test

In recent years, electrochemical oxidation (EO) shows the characteristics of green and high efficiency in removing chemical oxygen demand (COD) and ammonia nitrogen (NH₃-N) from wastewater, which has been favored by researchers. However, at present, most of current studies on EO remain in laboratory stage, reports about pilot-scale or even industrial tests with large treatment capacity are few, which slowing down the use of the advanced technology to practical application. In this study, bench-scale tests, pilot-scale tests (treatment capacity 200-500 L/h), and industrial tests (treatment capacity 100 m³/h) were carried out by EO technology in view of the characteristics of tungsten smelting wastewater (TSW) with high salinity (NaCl), COD, and NH₃-N. Results showed that the removal of COD and NH₃-N was a competitive reaction in the EO process, and COD could be removed more preferentially than NH₃-N. When NH₃-N content was low, the influent pH had a minimal effect on its removal, and when NH₃-N content was high, increasing the influent pH was beneficial to its removal. Industrial tests showed that the one-step removal of COD and NH₃-N in TSW met the standard, and the power consumption per cubic meter of wastewater was only 4.2 kW h, and the treatment cost was much lower than the two-step process of "breaking point chlorination to remove NH₃-N and adding oxidant to remove COD". This study has successfully realized industrial application of EO technology in TSW treatment for the first time and provided a successful case, which is helpful to accelerate the popularization and application of this technology in the field of high salinity organic ammonia nitrogen wastewater treatment.

Peroxymonosulfate activation with an α-MnO2/Mn2O3/Mn3O4 hybrid system: parametric optimization and oxidative degradation of organic dye

The present study proposed the synthesis of low-toxicity and eco-friendly spherically shaped manganese oxides (α-MnO₂, Mn₂O₃, and Mn₃O₄) by using the chemical precipitation method. The unique variable oxidation states and different structural diversity of manganese-based materials have a strong effect on fast electron transfer reactions. XRD, SEM, and BET analyses were used to confirm the structure morphology, higher surface area, and excellent porosity. The catalytic activity of as-prepared manganese oxides (MnO_x) was investigated for the rhodamine B (RhB) organic pollutant with peroxymonosulfate (PMS) activation under the condition of control pH. In acidic conditions (pH = 3), complete RhB degradation and 90% total organic carbon (TOC) reduction were attained in 60 min. The effects of operating parameters such as solution pH, PMS loading, catalyst dosage, and dye concentration on RhB removal reduction were also tested. The different oxidation states of MnO_x promote the oxidative-reductive reaction under acidic conditions and enhance the SO₄^•-/^•OH radical formation during the treatment, whereas the higher surface area offers sufficient absorption sites for interaction of the catalyst with pollutants. A scavenger experiment was used to investigate the generation of more reactive species that participate in dye degradation. The effect of inorganic anions on divalent metal ions that genuinely occur in water bodies was also studied. Additionally, separation and mass analysis were used to investigate the RhB dye degradation mechanism at optimum conditions based on the intermediate's identification. Repeatability tests confirmed that MnO_x showed superb catalytic performance on its removal trend.

Application of KHSO5 for remediation of soils polluted by organochlorides: A comprehensive study on the treatment's efficacy, environmental implications, and phytotoxicity

Soil pollution caused by complex organochloride mixtures has been increasing in many parts of the world in recent years; as a result, countless numbers of people are exposed to dangerous pollutions; hence, the treatment of organochlorides-polluted soils is gaining considerable attention. In this study, the potential of unactivated peroxymonosulfate (KHSO₅) in remediating soil co-contaminated with trichlorophenol, para-dichlorobenzene, and para-chloro-meta-cresol was investigated. In addition, the treatment's collateral effect on critical soil properties was explored. The result revealed that treating 10 g of soil with 20 mL of 5 mM KHSO₅ for 60 min could oxidize 70.49% of the total pollutants. The pH of the soil was decreased following the treatment. The significant decrease, (p < 0.05), in the soil organic matter following the remediation has affected cation exchange capacity, and available nitrogen. It was also observed that the treatment reduced the β-glucosidase, urease, invertase, and cellulase activities significantly, (p < 0.05). The treatment, on the other hand, brought negligible effects on available phosphorus, available potassium, and particle size distribution. The phytotoxicity tests, which included seed germination and root elongation and soil respiration tests revealed that the treatment did not leach toxins into the treated soil. The treatment method was found to be relatively ecofriendly and cost effective.

Exploring the potential of Fe(III)-EGTA and Fe(III)-DTPA as the catalysts to enhance UV/persulfate in the degradation of aqueous sulfamethazine

The combination of UV and water-soluble Fe(III) complexes is an effective method for generating Fe(II) in situ for activating advanced oxidation processes. This study explored the potential of Fe(III)-diethylenetriaminepentaacetic acid (Fe(III)-DTPA) and Fe(III)-ethylene glycol-bis(2-aminoethylether)-N,N,N',N'-tetraacetic acid (Fe(III)-EGTA) in activating the UV/persulfate (UV/PS) for sulfamethazine removal. The initial screening showed that Fe(III)-EGTA and Fe(III)-DTPA could significantly improve the rate of sulfamethazine removal. The optimum molar ratios of persulfate to Fe(III)-DTPA and Fe(III)-EGTA were 100:1 and 100:2.5. The predicted percentage of sulfamethazine removal under the optimized conditions, obtained using response surface methodology, was ~99% for both catalysts. The pH range of 6 to 8 did not significantly affect the performance of UV/PS in the removal of sulfamethazine. The percentage sulfamethazine removal in the selected water samples was ranged from 93.6% to 99.6%, agreeing with the predicted value. The performance of both catalysts in activating UV/PS is comparable with that of the frequently used Fe(III)-EDDS. PRACTITIONERS POINTS: The potential of Fe(III)-DTPA and Fe(III)-EGTA in activating UV/persulfate (UV/PS) was explored. Fe(III)-DTPA and Fe(III)-EGTA improved the performance of UV/PS in sulfamethazine removal. Fe(III)-DTPA and Fe(III)-EGTA are effective in catalyzing UV/PS under pH 6 to 8. The performance of Fe(III)-DTPA and Fe(III)-EGTA is comparable with well-studied Fe(III)-EDDS.

Applications of biochar in sulfate radical-based advanced oxidation processes for the removal of pharmaceuticals and personal care products

Recently, biochar (BC) has been increasingly used as a catalyst for the degradation of 'emerging pollutants' (EPs). Pharmaceuticals and personal care products (PPCPs), which come under 'EPs', can be harmful to the aquatic ecosystem despite being present in very low concentrations (ng/L-μg/L). Advanced oxidation processes (AOPs), which produce sulfate radical (SR-AOPs), show a great potential to degrade PPCPs effectively from wastewater. It is mainly due to the higher stability, long half-lives and better non-selectivity of SO₄^{• -} compared with AOPs with •OH generation. Furthermore, research focus is now given on AOPs coupled with BC-supported catalyst to enhance the degradation of PPCPs because of quicker generation of radicals (•OH, SO₄^•-) by the activation of persulfate (PS) and peroxymonosulfate (PMS). This article sheds light on the catalytic ability of BC after its physical and chemical modifications such as acid/alkali treatment and metal doping. The role of persistent free radicals (PFRs) in the BC for effective removal of PPCPs has been elaborated. Its potential applications in synthetic as well as real wastewater have also been discussed.

The multiple roles of phenols in the degradation of aniline contaminants by sulfate radicals: A combined study of DFT calculations and experiments

Recent research revealed inhibition or enhancement of dissolved organic matter (DOM) to the degradation of trace organic contaminants (TrOC) in natural and engineered water systems. Phenols containing acetyl, carboxyl, formyl, hydroxy, and methoxy groups were selected as the model DOM to quantitatively study their roles in the degradation of simple anilines, sulfonamide antibiotics, phenylurea pesticides by sulfate radicals (SO₄^•-). Experimental results found that p-methoxyphenol inhibited aniline and sulfamethoxazole degradation by thermally activated peroxydisulfate (TAP), while p-acetylphenol slightly promoted aniline degradation. Quantum chemical calculations were applied to study the microscopic mechanism and kinetics of phenols affecting the degradation of aniline pollutants (AN) in three ways: competitively reacting with SO₄^•-, repairing aniline cationic radicals (AN^•+) and phenylaminyl radicals (AN(-H)^•), and generating phenoxy radicals to degrade anilines. Generally, the degradation of sulfonamides and phenylureas prefer to be inhibited by hydroxy- and methoxy-phenols with low oxidation potential (E_ox), due to their diffusion-limiting reaction with SO₄^•- and rapid back-reduction AN^•+ with the calculated rate constants of (0.02 - 6.38) × 10⁹ M^-1 s^-1. Phenols repairing AN(-H)^• through H abstraction reaction is speculated to possibly dominate the joint degradation of phenols and anilines by TAP, which has a poor correlation with E_ox. This study provides mechanistic insight into the chemical behavior of complex and heterogeneous DOM in complex aqueous environments.

Waste to catalyst: Role of agricultural waste in water and wastewater treatment

Presently, owing to the rapid development of industrialization and urbanization activities, a huge quantity of wastewater is generated that contain toxic chemical and heavy metals, imposing higher environmental jeopardies and affecting the life of living well-being and the economy of the counties, if not treated appropriately. Subsequently, the advancement in sustainable cost-effective wastewater treatment technology has attracted more attention from policymakers, legislators, and scientific communities. Therefore, the current review intends to highlight the recent development and applications of biochars and/or green nanoparticles (NPs) produced from agricultural waste via green routes in removing the refractory pollutants from water and wastewater. This review also highlights the contemporary application and mechanism of biochar-supported advanced oxidation processes (AOPs) for the removal of organic pollutants in water and wastewater. Although, the fabrication and application of agriculture waste-derived biochar and NPs are considered a greener approach, nevertheless, before scaling up production and application, its toxicological and life-cycle challenges must be taken into account. Furthermore, future efforts should be carried out towards process engineering to enhance the performance of green catalysts to improve the economy of the process.

La2CoO4+δ perovskite-mediated peroxymonosulfate activation for the efficient degradation of bisphenol A

Sulfate radical-based technology has been considered as an efficient technology to remove pharmaceuticals and personal care products (PPCPs) with heterogeneous metal-mediated catalysts for the activation of peroxymonosulfate (PMS). In this study, La₂CoO_4+δ perovskite with Ruddlesden-Popper type structure was synthesised by the sol-gel method, which was employed in PMS activation. Different characteriazation technologies were applied for the characterization of La₂CoO_4+δ , such as SEM-EDX, XRD, and XPS technologies. A common organic compound, bisphenol A (BPA), is used as a target contaminant, and the effect impactors were fully investigated and explained. The results showed that when the dosage of La₂CoO_4+δ was 0.5 g L^-1 and the concentration of PMS was 1.0 mM in neutral pH solution, about 91.1% degradation efficiency was achieved within 25 minutes. Quenching experiments were introduced in the system to verify the catalytic mechanism of PMS for the BPA degradation, proving the existence of superoxide, hydroxyl radicals and sulfate radicals, which are responsible for the catalytic degradation of BPA. Moreover, the reusability and stability of the catalyst were also conducted which showed good stability during the reaction. This work would improve the applications of A₂BO₄-type perovskites for activating PMS to degrade BPA.

Sulfate radicals-based advanced oxidation processes for the degradation of pharmaceuticals and personal care products: A review on relevant activation mechanisms, performance, and perspectives

Owing to the rapid development of modern industry, a greater number of organic pollutants are discharged into the water matrices. In recent decades, research efforts have focused on developing more effective technologies for the remediation of water containing pharmaceuticals and personal care products (PPCPs). Recently, sulfate radicals-based advanced oxidation processes (SR-AOPs) have been extensively used due to their high oxidizing potential, and effectiveness compared with other AOPs in PPCPs remediation. The present review provides a comprehensive assessment of the different methods such as heat, ultraviolet (UV) light, photo-generated electrons, ultrasound (US), electrochemical, carbon nanomaterials, homogeneous, and heterogeneous catalysts for activating peroxymonosulfate (PMS) and peroxydisulfate (PDS). In addition, possible activation mechanisms from the point of radical and non-radical pathways are discussed. Then, biodegradability enhancement and toxicity reduction are highlighted. Comparison with other AOPs and treatment of PPCPs by the integrated process are evaluated as well. Lastly, conclusions and future perspectives on this research topic are elaborated.

Pre-treatment of real pharmaceutical wastewater by heterogeneous Fenton and persulfate oxidation processes

This study compares the pre-oxidation of pharmaceutical wastewater by hydroxyl radical based advanced oxidation (HR-AOP) and a sulfate radical based advanced oxidation process (SR-AOP). The heterogeneous Fenton process is chosen as a model HR-AOP and persulfate (PS) activation as a model SR-AOP. The pre-treatment efficacy of both processes in terms of TOC, and COD removals using Fe₃O₄-rGO catalyst were considered. Under the investigated experimental conditions, both processes yielded fluctuating COD values with time. The heterogeneous Fenton process discovered to be the most efficient to remove 68.7% TOC in 180 min of treatment, when Fe₃O₄-rGO: H₂O₂ = 300 mg L^-1:150 mM H₂O₂ was used at pH 3. Notably, the heterogeneous Fenton system was not considerably inhibited at the natural pH of pharmaceutical wastewater (6.75), as the process successfully removed 64.6% TOC. On the other hand, in persulfate activation studies, Fe₃O₄-rGO: PS = 400 mg L^-1: 5 mM was the ideal condition for removing 59.5% TOC in 180 min at pH 3. Whereas the natural pH condition significantly inhibited the TOC removal, as only 20.8% TOC removal was feasible. The wastewater characterisation before and after Fenton treatment reveals that Fenton oxidation leads to an increase in inorganics (chlorides: 160 ± 15 mg L^-1, nitrates: 63.14 ± 3.08 mg L^-1, sulfates: 266.31 ± 31.39 mg L^-1) necessitating an additional treatment step to reduce COD and inorganics further.

Degradation of Textile Dye by Bimetallic Oxide Activated Peroxymonosulphate Process

The sulphate radical based advanced oxidation processes (AOPs) are highly in demand these days, owing to their numerous advantages. Herein, the Fe-Mn bimetallic oxide particle was used to activate peroxymonosulphate (PMS) for Rhodamine B (RhB) degradation. Three bimetallic catalysts were synthesized via the chemical precipitation method with different concentrations of metals; Fe-Mn (1:1), Fe-Mn (1:2) and Fe-Mn (2:1). The best performance was shown by Fe-Mn (2:1) system at optimized conditions; 96% of RhB was removed at optimized conditions. Scavenging experiments displayed the clear dominance of hydroxyl radical in pH 3, while sulphate radical was present in a large amount at pH 7 and 10. The monometallic Fe and Mn oxides were also synthesized to confirm the synergistic effect that was present in the bimetallic oxide system. The application of optimized condition in real textile wastewater was conducted, which revealed the system works efficiently at high concentrations of PMS and catalyst dosage.

Contribution of electrolyte in parametric optimization of perfluorooctanoic acid during electro-oxidation: Active chlorinated and sulfonated by-products formation and distribution

The present study investigated the roles of peroxydisulfate (PDS) radicals and sulfate radicals (SO₄^•-) that formed from sulfate (SO₄^2-) during electrochemical oxidation of perfluorooctanoic acid (PFOA). The effect of operating parameters such as different types of electrolytes (NaCl, NaClO₄, and Na₂SO₄), initial pH, current density, dose of electrolyte, and initial concentration of PFOA using electrochemical oxidation for perfluorooctanoic acid (PFOA) decomposition study was investigated. A difference in the removal efficiency with different electrolytes (i.e., Cl^-, ClO₄^-, and SO₄^2-) illustrated an increasing effect of electrooxidation of PFOA in the order of ClO₄^- < Cl^- < SO₄^2-, which suggested that ^•OH induced oxidation and direct e^- transfer reaction continued to play a crucial role in oxidation of PFOA. At the optimum treatment condition of j = 225.2 Am^-2, Na₂SO₄ concentration = 1.5 gL^-1, [PFOA]_o = 50 mgL^-1 and initial pH = 3.8 maximum PFOA removal of 92% and TOC removal of 80% was investigated at 240 min. The formation of three shorter-chain perfluorocarboxylates (i.e., perfluoroheptanoic acid (PFHpA), perfluorohexanoic acid (PFHxA), and perfluoropentanoic acid (PFPeA) and formate (HCOO^-) ions were detected as by-products of PFOA electro-oxidation, showing that the C-C bond first broken in C₇F₁₅ and then mineralized into CO₂, and fluoride ion (F^-). The fluorine recovery as F^- ions and the organic fluorine as the shorter-chain by-products were also obtained. The degradation kinetic has also been studied using the nth-order kinetic model.

Positively charged membranes for dye/salt separation based on a crossover combination of Mannich reaction and prebiotic chemistry

With the advent of increasingly loose nanofiltration membranes for dye desalination, synthesis methods based on interfacial polymerization and bio-inspired materials such as polydopamine (pDA) have been investigated. However, the long polymerization time of pDA greatly limits the synthesis and application of fast dye/salt separation membranes. In this work, prebiotic chemistry-inspired aminomalononitrile (AMN) was used as a binder to co-deposit the Mannich reaction of tetrakis(hydroxymethyl)phosphonium chloride (THPC) and polyethyleneimine (PEI) to form the positively charged selective layer rapidly. The optimum membrane had a water permeance of 30.7 LMH bar^-1 and a rejection of positively charged Victoria blue B (VBB, 200 ppm) and Na₂SO₄ (1 g/L) of 99.5 % and 9.9 %, respectively. Moreover, the results of a practical application test showed that it had excellent separation performance towards various positively charged dyes and salts. In addition, the actual application test results show that the membrane has good long-term stability during application. In terms of antifouling and antibacterial, the membrane has excellent antibacterial and antifouling properties., Further antibacterial tests were carried out, and the inactivation effect of the membrane on E. coli was also confirmed. The preparation method proposed in this work provides technical support for developing new dye/salt separation membranes.