Gold-nanoparticle-embedded nafion composite modified on glassy carbon electrode for highly selective detection of arsenic(III)

Anodic stripping voltammetry of arsenic determination with edible mushroom-nafion-modified glassy carbon electrode

An edible Mushroom-Nafion modified glassy carbon electrode (M2N5-GCE) was prepared using a homogeneous mixture varying the concentrations of these, in addition to the origin of the mushroom (Shiitake, Lentinula edodes, M1 and Abrantes, Agariscus bisporus, M2) and applied to the As(III) determination by anodic stripping voltammetry. After choosing the optimal conditions in the preparation of the electrode, the second stage was to study the effects of various parameters such as supporting electrolyte, pH, accumulation potential, and time (Eacc, tacc). The optimum experimental conditions chosen were Britton Robinson buffer 0.01 mol L-1 pH:4.6; Eacc: -1.0 and tacc: 60 s obtaining a signal of oxidation of As(0) to As(III) about 0.08 V. Peak current was proportional to arsenic concentration over the 19.6-117.6 μg L-1 range, with a 3σ detection limit of 13.4 μg L-1. The method was validated using As(III) spiked tap water from the laboratory with satisfactory results (RE:3.0 %). Finally, the method was applied to the determination of As(III) in water samples from the Loa River (Northern Chile) in the presence of As(V) in a concentration >20 times higher (RE: 2.3 %).

High Sensitivity Electrochemical As (III) Sensor Based on Fe3O4/MoS2 Nanocomposites

Currently, heavy metal ion pollution in water is becoming more and more common, especially As (III), which is a serious threat to human health. In this experiment, a glassy carbon electrode modified with Fe3O4/MoS2 nanocomposites was used to select the square wave voltammetry (SWV) electrochemical detection method for the detection of trace As (III) in water. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) showed that Fe3O4 nanoparticles were uniformly attached to the surface of MoS2 and were not easily agglomerated. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) showed that Fe3O4/MoS2 has higher sensitivity and conductivity. After optimizing the experimental conditions, the Fe3O4/MoS2-modified glassy carbon electrode exhibited high sensitivity (3.67 μA/ppb) and a low detection limit (0.70 ppb), as well as excellent interference resistance and stability for As (III).

Electrodeposited rGO/AuNP/MnO2 Nanocomposite-Modified Screen-Printed Carbon Electrode for Sensitive Electrochemical Sensing of Arsenic(III) in Water

Herein, a simple and portable electrochemical sensor based on a reduced graphene oxide/gold nanoparticle/manganese dioxide (rGO/AuNP/MnO₂) nanocomposite-modified screen-printed carbon electrode (SPCE) was constructed by the facile stepwise electrodeposition method and used for electrochemical detection of As(III). The resultant electrode was characterized for its morphological, structural, and electrochemical properties using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). From the morphologic structure, it can be clearly observed that the AuNPs and MnO₂ alone or their hybrid were densely deposited or entrapped in thin rGO sheets on the porous carbon surface, which may favor the electro-adsorption of As(III) on the modified SPCE. It is interesting that the nanohybrid modification endows the electrode with a significant decrease in charge transfer resistance and an increase in electroactive specific surface area, which dramatically increases the electro-oxidation current of As(III). This improved sensing ability was ascribed to the synergistic effect of gold nanoparticles with excellent electrocatalytic property and reduced graphene oxide with good electrical conductivity, as well as the involvement of manganese dioxide with a strong adsorption property in the electrochemical reduction of As(III). Under optimized conditions, the sensor can detect As(III) via square wave anodic stripping voltammetry (SWASV) with a low limit of detection of 2.4 μg L^-1 and a linear range of 25-200 μg L^-1. The proposed portable sensor shows the advantages of a simple preparation procedure, low cost, good repeatability, and long-term stability. The feasibility of rGO/AuNPs/MnO₂/SPCE for detecting As(III) in real water was further verified.

Surface Defects Improved SERS Activity of Nanoporous Gold Prepared by Electrochemical Dealloying

Nanoporous metals possess excellent catalytic and optical properties that are related with surface morphology. Here, we modulated the ligament surface of nanoporous gold (NPG) by controlling electrochemical dealloying and obtained NPG with an improved enhancement of its surface-enhanced Raman scattering (SERS) property. We found that both high-density atomic steps and kinks on the curved surfaces and high-content silver atoms close to the ligament surface contributed to the high SERS ability. The presented strategy will be useful for the fabrication of nanoporous metal with an excellent surface that is needed for sensing, conversion, and catalytic.

An application of miniaturized electrochemical sensing for determination of arsenic in herbal medicines

This study aimed to create a miniaturized electrochemical platform for detecting As(III) contamination in herbal medicines. To reduce the operational steps of modification and determination, only a single drop of mixed standard Au(III) and sample solution is proposed to perform the electrochemical measurements using a screen-printed graphene electrode (SPGE). Square wave anodic stripping voltammetry was employed to integrate the simultaneous modification and determination processes. To perform the measurement, As(III) and Au(III) migrate to the SPGE surface while the reduction potential is held at -0.5 V, forming an Au-As intermetallic alloy. Then, As is stripped off for the electrochemical determination of As(III). The total assay time is less than 3 min. Under suitable conditions, the electrochemical sensing system can detect As(III) at concentrations ranging from 0.1 to 3.0 ppm, with a limit of quantification and limit of detection of 0.1 and 0.03 ppm, respectively. The applicability and accuracy of the proposed sensor were verified by determining As(III) in herbal medicinal samples, and they were found to be in line with the standard method (ICP-OES). The benefits of simple operation, rapid detection, portability, and low cost (<1 USD) make this a more powerful tool for routine monitoring and on-site analysis applications.

Anodic Stripping Voltammetric Analysis of Trace Arsenic(III) on a Au-Stained Au Nanoparticles/Pyridine/Carboxylated Multiwalled Carbon Nanotubes/Glassy Carbon Electrode

A Au-stained Au nanoparticle (Au_s)/pyridine (Py)/carboxylated multiwalled carbon nanotubes (C-MWCNTs)/glassy carbon electrode (GCE) was prepared for the sensitive analysis of As(III) by cast-coating of C-MWCNTs on a GCE, electroreduction of 4-cyanopyridine (cPy) to Py, adsorption of gold nanoparticles (AuNPs), and gold staining. The Py/C-MWCNTs/GCE can provide abundant active surface sites for the stable loading of AuNPs and then the AuNPs-initiated Au staining in HAuCl₄ + NH₂OH solution, giving a large surface area of Au on the Au_s/Py/C-MWCNTs/GCE for the linear sweep anodic stripping voltammetry (LSASV) analysis of As(III). At a high potential-sweep rate of 5 V s⁻¹, sharp two-step oxidation peaks of As(0) to As(III) and As(III) to As(V) were obtained to realize the sensitive dual-signal detection of As(III). Under optimal conditions, the ASLSV peak currents for oxidation of As(0) to As(III) and of As(III) to As(V) are linear with a concentration of As(III) from 0.01 to 8 μM with a sensitivity of 0.741 mA μM⁻¹ and a limit of detection (LOD) of 3.3 nM (0.25 ppb) (S/N = 3), and from 0.01 to 8.0 μM with a sensitivity of 0.175 mA μM⁻¹ and an LOD of 16.7 nM (1.20 ppb) (S/N = 3), respectively. Determination of As(III) in real water samples yielded satisfactory results.

Advances in Electrochemical Detection Electrodes for As(III)

Arsenic is extremely abundant in the Earth’s crust and is one of the most common environmental pollutants in nature. In the natural water environment and surface soil, arsenic exists mainly in the form of trivalent arsenite (As(III)) and pentavalent arsenate (As(V)) ions, and its toxicity can be a serious threat to human health. In order to manage the increasingly serious arsenic pollution in the living environment and maintain a healthy and beautiful ecosystem for human beings, it is urgent to conduct research on an efficient sensing method suitable for the detection of As(III) ions. Electrochemical sensing has the advantages of simple instrumentation, high sensitivity, good selectivity, portability, and the ability to be analyzed on site. This paper reviews various electrode systems developed in recent years based on nanomaterials such as noble metals, bimetals, other metals and their compounds, carbon nano, and biomolecules, with a focus on electrodes modified with noble metal and metal compound nanomaterials, and evaluates their performance for the detection of arsenic. They have great potential for achieving the rapid detection of arsenic due to their excellent sensitivity and strong interference immunity. In addition, this paper discusses the relatively rare application of silicon and its compounds as well as novel polymers in achieving arsenic detection, which provides new ideas for investigating novel nanomaterial sensing. We hope that this review will further advance the research progress of high-performance arsenic sensors based on novel nanomaterials.

Electrochemical detection of selected heavy metals in water: a case study of African experiences

The safety of water resources throughout the globe has been compromised by various human activities and climate change over the last decades.

Electrochemical Mini-Platform with Thread based Electrodes for Interference Free Arsenic Detection

Herein, a fully integrated thread/textile-based electrochemical sensing device has been demonstrated. A hydrophilic conductive carbon thread, chemically modified with gold nanoparticles through an electrodeposition process, was used as a working electrode (WE). The hydrophilic thread coated with Ag/AgCl and an unmodified bare hydrophilic thread were used as reference electrode (RE) and counter electrode (CE) respectively. The device was fabricated with hydrophilic conductive carbon threads supported by capillary tubes and these integrated electrodes were placed in a 2 mL glass vial. The physico-chemical characterization of the working electrode was carried out using SEM (scanning electron microscopy) and X-ray photoelectron spectroscopy (XPS). Furthermore, the fabricated sensing platform, was tested for electrochemical sensing of arsenic. The electrocatalytic oxidation activity of arsenic in the designed platform was investigated via cyclic voltammetry (CV) and square wave Voltammetry (SWV). An oxidation peak at -0.4 V corresponding to the oxidation of arsenic was obtained. Scan rate effect was performed using CV analysis and the diffusion coefficient was found to be 2.478×10-10 with a regression coefficient of R2 = 0.9647. Further, concentration effect was accomplished in the linear range 0.4 μM to 60 μM. The limit of detection was obtained as 0.416 μM. For the practical application, effect of interference from other chemicals and real sample analysis from the tap water and blood serum sample was carried out which gave remarkable recovery values.

Preparation of GO/Fe3O4@PMDA/AuNPs nanocomposite for simultaneous determination of As3+ and Cu2+ by stripping voltammetry

One of the critical challenges in the simultaneous determination of As³⁺ and Cu²⁺ by stripping voltammetry is the overlapping of their oxidation peaks. Therefore, the engineering of nanostructured sensors in order to uplift their electrochemical performance is a significant issue for the codetection of As³⁺ and Cu²⁺. Herein, we modified a glassy carbon electrode with a new nanocomposite based on poly methyldopa along with gold nanoparticles immobilized on the surface of magnetic graphene oxide (GCE/GO/Fe₃O₄@PMDA/AuNPs) that can determine As³⁺ and Cu²⁺ with great sensitivity. Optimization of the measurement conditions by square wave stripping voltammetry (SWSV) caused the oxidation peaks of As³⁺ and Cu²⁺ to be distinguished significantly from each other, while the peak currents of As³⁺ and Cu²⁺ increased 9-12 fold, respectively, compared to the bare electrode. The proposed electrode exhibits low detection limits (S/N ≥ 3): 0.15 ppb for As³⁺ and 0.11 ppb for Cu²⁺. The GCE/GO/Fe₃O₄@PMDA/AuNPs also has good linearity over a wide concentration range from 5 to 500 ppb for As³⁺ and 0.5-750 ppb for Cu²⁺. The good recovery values were obtained for the analysis of As³⁺ and Cu²⁺ in pool and drinking water samples.

Nano-Enabled sensors for detection of arsenic in water

The elevated cases of arsenic contamination reported across the globe have made its early detection and remediation an active area of research. Although, the World Health Organisation has set the maximum provisional value for arsenic in drinking water at 10 parts per billion, yet concentrations as high as 5000 parts per billion are still reported. In human beings, chronic arsenic exposure can culminate into lethal diseases such as cancer. Thus, there is a need for urgent emergence of efficient and reliable detection system. This paper offers an overview of the state-of-art knowledge on current arsenic detection mechanisms. The central agenda of this paper is to develop an understanding into the nano-enabled methods for arsenic detection with an emphasis on strategic fabrication of nanostructures and the modulation of nanomaterial chemistry in order to strengthen the knowledge into novel nano-enabled solutions for arsenic contamination. Towards the end prospects for arsenic detection in water are also prompted.

A novel and sensitive electrochemical sensor based on nanoporous gold for determination of As(III)

Three-dimensional porous gold nanoparticles (NPG) were synthesized in situ on indium-doped tin oxide (ITO) substrates by a green and convenient one-step electrodeposition method to achieve super-sensitive As(III) detection. The introduction of NPG method not only greatly improves the electron transfer capacity and surface area of sensor interface but provides more active sites for As(III) enrichment, thus boosting sensitivity and selectivity. The sensor was characterized by scanning electron microscopy, energy dispersion spectroscopy, differential pulse anode stripping voltammetry (DPASV), and electrochemical impedance to evaluate its morphology, composition, and electrochemical performance. The wall thickness of NPG was customized by optimizing the concentration of electroplating solution, dissolved electrolyte, deposition potential, and reaction time. Under optimal conditions, the electrochemical sensor showed a wide linear range from 0.1 to 50 μg/L As(III), with a detection limit (LOD) of 0.054 μg/L (S/N = 3). The LOD is far below 10 μg/L, the recommended maximum value by the world health organization for drinking water. Stability, reproducibility, and repeatability of NGP/ITO were determined to be 2.77%, 4.9%, and 4.1%, respectively. Additionally, the constructed sensor has been successfully applied to determine As(III) in three actual samples, and the results are in good agreement with that of hydride generation atomic fluorescence spectrometry (AFS). Graphical abstract.

A Schiff base modified graphene oxide film for anodic stripping voltammetric determination of arsenite

A protocol is described for chemical modification of graphene oxide with a Schiff base derived from diethylenetriamine and 2-hydroxy-4-methoxybenzophenone. The base was grafted onto an indium tin oxide (ITO) film and applied to electroanalytical determination of arsenite. Successful grafting was confirmed by Fourier transform-infrared spectroscopy, spectrophotometry, field emission scanning electron microscopy and cyclic voltammetry. Secondly, the coated ITO film served as a working electrode for the stripping voltammetric determination of arsenite. The analytical signal is generated by selective oxidation of metal species via multi-donor sites present in the derivatized Schiff base. The electroanalytical protocol was optimized by investigating the effects of deposition time, working potential, frequency and amplitude of square wave anodic stripping voltammetry. The method has attractive features including (a) the usage of a non-metallic, non-toxic and cost-effective material; (b) improved sensitivity (with limit of detection as low as 156 pM) due to better adsorption of arsenite in the Schiff base pockets on the ITO, and (c) the application to the determination of arsenite in real samples. Graphical abstract Schematic representation of the fabrication of a Schiff base-functionalized graphene oxide on an indium tin oxide (SB@SiO2@GO@ITO) electrode for selective electrochemical sensing of arsenite due to adsorption on multi-donor sites.

Preparation of Au nanoparticles on a magnetically responsive support via pyrolysis of a Prussian blue composite

A strategy is described for the direct preparation of Au nanoparticles (AuNPs) on a Fe-based support, coated with porous carbon (PC), via pyrolysis of an AuCN functionalised Prussian Blue (PB) metal organic framework (MOF). The composite starting material was prepared with an even distribution of AuCN on the surface via galvanic exchange of PB with a gold salt in solution. The resulting structures after pyrolysis were shown to be active Au-based nanomaterials for model applications including catalysis (4-nitrophenol reduction) and electroanalysis (arsenic (III) detection), suggesting broad application where Au nanoparticles are required at a liquid-solid interface. The Fe based support was seen to consist of Fe, Fe₃C and Fe₄C phases, and the carbon coating increased the stability and improved the conductivity of the materials. The temperature of pyrolysis was seen to affect the activity of the supported nanoparticles, with an increased Au surface area obtained at the higher pyrolysis temperature (650 °C) tested. A general strategy is thus confirmed for preparation of noble metal nanoparticles evenly distributed on a magnetic support, allowing easy separation of catalysts from products in heterogeneous applications.

Electrochemical Detection of As(III) by a rGO/Fe3O4-modified Screen-Printed Carbon Electrode

A reduced graphene oxide (rGO)/Fe₃O₄ composites modified screen-printed carbon electrode (SPCE) was used to determinate As(III) in a HAc-NaAc buffer solution. The rGO/Fe₃O₄ composites were prepared by a simple and one-pot synthesis method, and characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM), FT-IR and Raman spectra. The electrochemical behaviors of the composite electrode were characterized by cycle voltammetry and electrochemical impedance spectroscopy. The experimental parameters, such as supporting electrolyte, solution pH, deposition potential, deposition time were optimized, respectively. The calibration curve for the detection of As(III) in the range of 2 to 20 ppb was I = -4.495 + 1.922C, with a coefficient of 0.994. The sensitivity was 1.922 μA/ppb, and with about twice Fe₃O₄ modified SPCE, a detection limit as low as 0.3 ppb was achieved. The proposed electrode was validated by analyzing the As(III) content in real water samples.

Towards cancer diagnostics – an α-feto protein electrochemical immunosensor on a manganese(iv) oxide/gold nanocomposite immobilisation layer

A novel electrochemical immunosensor for the quantification of α-feto protein (AFP) using a nanocomposite of manganese(iv) oxide nanorods (MnO₂NRs) and gold nanoparticles (AuNPs) as the immobilisation layer is presented. The MnO₂NRs was synthesised using a hydrothermal method and AuNPs were electrodeposited on a glassy carbon electrode surface. The MnO₂NRs were characterised with scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM) and X-ray powder diffraction (XRD). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterise the immunosensor at each stage of the biosensor preparation. The MnO₂ nanorods and AuNPs were applied as the immobilisation layer to efficiently capture the antibodies and amplify the electrochemical signal. Under optimised conditions, the fabricated immunosensor was utilised for the quantification of AFP with a wide dynamic range of 0.005 to 500 ng mL⁻¹ and detection limits of 0.00276 ng mL⁻¹ and 0.00172 ng mL⁻¹ (S/N = 3) were obtained from square wave anodic stripping voltammetry and EIS respectively. The nanocomposite modifier enhanced the immunosensor performance. More so, this label-free immunosensor possesses good stability over a period of two weeks when stored at 4 °C and was selective in the presence of some interfering species.

A novel electrochemical immunosensor for the quantification of α-feto protein (AFP) using a nanocomposite of manganese(iv) oxide nanorods (MnO₂NRs) and gold nanoparticles (AuNPs) as the immobilisation layer is presented.

Electrochemical determination of arsenic in natural waters using carbon fiber ultra-microelectrodes modified with gold nanoparticles

We have developed an anodic stripping voltammetry method that employs carbon fiber ultra-microelectrodes modified with gold nanoparticles to determine arsenic in natural waters. Gold nanoparticles were potentiostatically deposited on carbon fiber ultra-microelectrodes at -0.90V (vs SCE) for a time of 15s, to form the carbon fiber ultra-microelectrodes modified with gold nanoparticles. Cyclic voltammetry, electrochemical impedance spectroscopy and scanning electron microscopy coupled to an X-ray microanalysis system were used to check and confirm the presence of gold nanoparticles on the carbon fiber ultra-microelectrodes. Arsenic detection parameters such as deposition potential and deposition time were optimized allowing a detection range between 5 to 60µgL^-1. The developed modified electrodes allowed rapid As determination with improved analytical characteristics including better repeatability, higher selectivity, lower detection limit (0.9μgL^-1) and higher sensitivity (0.0176nAμgL^-1) as compared to the standard carbon electrodes. The analytical capability of the optimized method was demonstrated by determination of arsenic in certified reference materials (trace elements in water (NIST SRM 1643d)) and by comparison of results with those obtained by hydride generation atomic absorption spectrometry (HG-AAS) in the determination of the analyte in tap and well waters.

How cutting-edge technologies impact the design of electrochemical (bio)sensors for environmental analysis. A review

Through the years, scientists have developed cutting-edge technologies to make (bio)sensors more convenient for environmental analytical purposes. Technological advancements in the fields of material science, rational design, microfluidics, and sensor printing, have radically shaped biosensor technology, which is even more evident in the continuous development of sensing systems for the monitoring of hazardous chemicals. These efforts will be crucial in solving some of the problems constraining biosensors to reach real environmental applications, such as continuous analyses in field by means of multi-analyte portable devices. This review (with 203 refs.) covers the progress between 2010 and 2015 in the field of technologies enabling biosensor applications in environmental analysis, including i) printing technology, ii) nanomaterial technology, iii) nanomotors, iv) biomimetic design, and (v) microfluidics. Next section describes futuristic cutting-edge technologies that are gaining momentum in recent years, which furnish highly innovative aspects to biosensing devices.

Label-free signal-on aptasensor for sensitive electrochemical detection of arsenite

A signal-on aptasensor was fabricated for highly sensitive and selective electrochemical detection of arsenite with a label-free Ars-3 aptamer self-assembled on a screen-printed carbon electrode (SPCE) via Au-S bond. The Ars-3 aptamer could adsorb cationic polydiallyldimethylammonium (PDDA) via electrostatic interaction to repel other cationic species. In the presence of arsenite, the change of Ars-3 conformation due to the formation of Ars-3/arsenite complex led to less adsorption of PDDA, and the complex could adsorb more positively charged [Ru(NH3)6](3+) as an electrochemically active indicator on the aptasensor surface, which produced a sensitive "turn-on" response. The target-induced structure switching could be used for sensitive detection of arsenite with a linear range from 0.2 nM to 100 nM and a detection limit down to 0.15 nM. Benefiting from Ars-3 aptamer, the proposed system exhibited excellent specificity against other heavy metal ions. The SPCE-based aptasensor exhibited the advantages of low cost and simple fabrication, providing potential application of arsenite detection in environment.

Shape dependent stripping behavior of Au nanoparticles toward arsenic detection: evidence of enhanced sensitivity on the Au (111) facet

This work reports a comparative study of gold cubes {100}, octahedra {111}, and rhombic dodecahedra {110} toward the detection of arsenic for the first time. Au octahedral nanoparticles were found to exhibit the highest sensitivity.

Robust and direct electrochemical sensing of arsenic using zirconia nanocubes

The presence of heavy metal ions in the environment and in food items can severely harm human health.

A facile Pt catalyst regeneration process significantly improves the catalytic activity of Pt–organic composites for the O2 reduction reaction

Combination of the “nano-size” effect and Cl⁻ complexation ability causes massive electrodissolution of Pt under acidic conditions to promote the regeneration of Pt–organic composites and to significantly improve the catalytic performance of the O₂ reduction reaction.