Two-step microextraction combined with high performance liquid chromatographic analysis of pyrethroids in water and vegetable samples

Small nanofibrous disks for preconcentration of environmental contaminants followed by direct in-vial elution and chromatographic determination

A novel method for the extraction of river water contaminants as model analytes of ranging polarities, including bisphenols A, C, S, Z, fenoxycarb, kadethrin, and deltamethrin, using small compact fibrous disks has been developed and validated. Polymer nanofibers and microfibers prepared from poly(3-hydroxybutyrate), polypropylene, polyurethane, polyacrylonitrile, poly(lactic acid), and polycaprolactone doped with graphene were evaluated in terms of extraction efficiency, selectivity, and stability in organic solutions. Our novel extraction procedure comprised preconcentration of analytes from 150 mL river water to 1 mL of eluent using a compact nanofibrous disk freely vortexed in the sample. Small nanofibrous disks with a diameter of 10 mm were cut from a compact and mechanically stable 1-2 mm thick micro/nanofibrous sheet. After 60 min extraction in a magnetically stirred sample located in a beaker, the disk was removed from the liquid and washed with water. Then, the disk was inserted into a 1.5 mL HPLC vial and extracted with 1.0 ml methanol upon short intensive shaking. Our approach avoided the undesired problems related to the manual handling typical of "classical" SPE procedure since the extraction was carried out directly in the HPLC vial. No sample evaporation, reconstitution, or pipetting was required. The nanofibrous disk is affordable, needs no support or holder, and its use avoids creation of plastic waste originating from disposable materials. Recovery of compounds from the disks was 47.2-141.4% depending on the type of polymer used and the relative standard deviations calculated from 5 extractions ranged from 6.1 to 11.8% for poly(3-hydroxybutyrate), 6.3-14.8% for polyurethane, and 1.7-16.2% for polycaprolactone doped with graphene. A small enrichment factor was obtained for polar bisphenol S using all sorbents. A higher preconcentration reaching up to 40-fold was achieved for lipophilic compounds such as deltamethrin when using poly(3-hydroxybutyrate) and graphene-doped polycaprolactone.

A Schiff base networks coated stir bar for sorptive extraction of pyrethroid pesticide residues in tobacco

Schiff base networks (SNWs) were introduced as a new stir bar coating, and a method of SNWs- coated stir bar sorptive extraction (SBSE) coupled to high performance liquid chromatography-ultraviolet detector (HPLC-UV) was developed for determination of pyrethroid pesticide residues in tobacco. The prepared amorphous SNWs polymer from melamine and 3,5-dihydroxybenzaldehyde riches in triazine rings, hydroxyl groups and amino groups, and the SNWs/polydimethylsiloxane (PDMS) stir bar prepared by sol-gel method can extract weakly polar pyrethroid pesticides through hydrophobic, π-π and hydrogen bonding. The SNWs/PDMS stir bar exhibited high extraction efficiency toward pyrethroid pesticides (70-76%) and good mechanical stability with reused time more than 50 times. Under the optimal experimental conditions, the limits of detection were 0.20 - 0.66 µg/L with relative standard deviation varying in the range of 2.3-8.2%, which meets the requirements of trace analysis of pesticide residues in the tobacco industry. The method was applied to the determination of six pyrethroid pesticides in cigarette samples, and the recovery for the spiked samples ranged from 82 to 117%, showing a great applicability for the analysis of pesticide residues in real samples with a complex sample matrix.

Dispersive magnetic solid-phase extraction for capsaicinoid compounds in human serum using LC-HRMS: targeted and non-targeted approaches

A new analytical method based on the use of dispersive magnetic solid-phase extraction (DMSPE) is described for the preconcentration of capsaicin (CAP), dihydrocapsaicin (DCAP), and N-vanillylnonanamide (PCAP) from human serum samples. The influence of several experimental factors affecting the adsorption (nature and amount of magnetic material, adsorption time, and pH) and desorption (nature of solvent, its volume and desorption time) steps was studied. Among seven different nanomaterials studied, the best results were obtained using magnetic multiwalled carbon nanotubes, which were characterized by means of spectrometry- and microscopy-based techniques. Analyses were performed by ultra-high-performance liquid chromatography with quadrupole-time-of-flight mass spectrometry using electrospray ionization in positive mode (UHPLC-ESI-Q-TOF-MS). The developed method was validated by obtaining several parameters, including linearity (0.3-300 μg L^-1 range), and limits of detection which were 0.1, 0.15, and 0.17 μg L^-1 for CAP, DCAP, and PCAP, respectively. The repeatability of the method, expressed as relative standard deviation (RSD, n = 7), varied from 3.4 to 11%. The serum samples were also studied through a non-targeted approach in a search for capsaicinoid metabolites and related compounds. With this objective, the fragmentation pathway of this family of compounds was initially studied and a strategy was established for the identification of novel or less studied capsaicinoid-derived compounds.

Systematic Stereoselectivity Evaluations of Tetramethrin Enantiomers: Stereoselective Cytotoxicity, Metabolism, and Environmental Fate in Earthworms, Soils, Vegetables, and Fruits

Tetramethrin is a widely applied type I chiral pyrethroid insecticide that exists as a mixture of four isomers. In the present study, its stereoselective cytotoxicity, bioaccumulation, degradation, and metabolism were investigated for the first time at the enantiomeric level in detail by using a sensitive chiral high-performance liquid chromatography-tandem mass spectroscopy (HPLC-MS/MS) method. Results showed that among rac-tetramethrin and its four enantiomers, the trans (+)-1R,3R-tetramethrin had the strongest inhibition effect on the PC12 cells. In the earthworm exposure trial, the concentration of trans (-)-1S,3S-tetramethrin was 0.94-8.92 times in earthworms (cultivated in natural soil) and 1.67-5.01 times (cultivated in artificial soil) higher than trans (+)-1R,3R-tetramethrin, respectively. In the greenhouse experiment, the trans (+)-1R,3R-tetramethrin and cis (+)-1R,3S-tetramethrin were preferentially degraded. Furthermore, for rat liver microsome in vitro incubation, the maximum metabolism rate of cis (-)-1S,3R-tetramethrin was 1.50 times higher than its antipodes. Altogether, the aim of this study was to provide a scientific and reasonable reference for the possibility of developing a single enantiomer to replace the application of rac-tetramethrin, which could possess better bioactivity and lower ecotoxicity, and thus permit more reliable and accurate environmental monitoring and risk assessment.

Modified DLLME-GC-TQMS determination of pesticide residues in Gomti River, Lucknow, India: ecological risk assessment and multivariate statistical approach

This research article aims to establish an easy and well-defined analytical method for detection and quantification of multiclass pesticides in Gomti river water samples because the increased agricultural activities, industrialization, and urbanization had increased the presence of pesticides in the ecosystem which causes the depletion of water quality making it a global concern. The analytical method, vortex-assisted ultrasonication-based dispersive liquid-liquid microextraction-solidification of floating organic droplets (VAUS-DLLME-SFO) was optimized using one parameter at a time approach which gave the recovery between 69.45 and 114.15%, limit of detection (LOD), and limit of quantification (LOQ) 0.0011-0.0111 µg/L and 0.0033-0.0368 µg/L, respectively, and RSD in the range of 0.75-1.29 which shows sensitivity and accuracy better than earlier reported methods. The data obtained were subjected to measurement uncertainty, risk assessment, and multivariate statistical analysis to establish the robustness of the developed analytical method. The measurement uncertainty found was concluded to be in the acceptable range for analytical results. Furthermore, the real samples were analyzed and the associated value of the risk quotient was found to be less than 1, except for aquatic invertebrates, establishing the fact that the current concentration of pesticides has no such negative threat to flora and fauna. The possible source of pesticides in the Gomti river system was established by multivariate analysis. It was thus concluded that anthropogenic activity is responsible for the variable concentration of pesticides found in the sample.

Counter Current Salting-out Homogenous Liquid-liquid Extraction and Dispersion Liquid-liquid Microextraction Based on the Solidification of Floating Organic Drop Followed by High-performance Liquid Chromatography for the Isolation and Preconcentration of Pesticides from Fruit Samples

BACKGROUND

Pesticides are widely used to control pests and prevent diseases in crops, including cereals, vegetables, and fruits. Due to factors such as the persistence of pesticides, bioaccumulation, and potential toxicity, the pesticide residues monitoring in foodstuffs is very important.

OBJECTIVE

In the current research, we proposed a novel approach to counter current salting-out homogenous liquid-liquid extraction (CCSHLLE) combined with dispersive liquid-liquid microextraction based on the solidification of floating organic drop (DLLME-SFO) in pesticides from aqueous samples for the isolation and preconcentration, which were evaluated prior to analysis as real samples by high-performance liquid chromatography-ultraviolet detection (HPLC-UV).

METHODS

In brief, sodium chloride was applied as a separation reagent, which is filled in a small glass column, through which a combination of an aqueous solution (here we could say as juice of fruit) and passing of acetonitrile. In this process, the droplets rose through the column and a separated layer would be formed on what has remained from aqueous phase. Following that, acetonitrile as the organic phase combined with 50.0 µL of extraction solvent. To further enrich the analytes, the mixture was injected into five milliliters of a 4% sodium chloride solution and placed in a tube for the DLLME-SFO.

RESULTS

Under optimal conditions, the dynamic linear range of 0.5-500 μg/L, extraction recovery of 65-85%, enrichment factors of 108-142, and limit of detection as 0.2-0.4 μg/L were obtained for the organophosphorus pesticides. In addition, the repeatability and reproducibility in the five replicate of the pesticides measurements (100 μg/L) are within the ranges of 3.5-5.1% and 4.5-6.3%, respectively.

New Trend in the Extraction of Pesticides from the Environmental and Food Samples Applying Microextraction Based Green Chemistry Scenario: A Review

This review focused on the green microextraction methods used for the extraction of pesticides from the environmental and food samples. Microextraction techniques have been explored and applied in various fields of analytical chemistry since its beginning, as evinced by the numerous reviews published. The success of any technique in science and technology is measured by the simplicity, environmentally friendly, and its applications; and the microextraction technique is highly successive. Deliberations were attentive to studies where efforts have been made to validate the methods through the inter-laboratory comparison study to assess the analytical performance of microextraction techniques against conventional methods. Succinctly, developed microextraction methods are shown to impart significant benefits over conventional techniques. Provided that the analytical community continues to put forward attention and resources into the growth and validation of the microextraction technique, a promising future for microextraction is forecasted.

Multivariate optimization of a dispersive liquid-liquid microextraction method for the determination of six antiparasite drugs in kennel effluent waters by using second-order chromatographic data

Six veterinary active ingredients (imidacloprid, albendazole, fenbendazole, praziquantel, fipronil and permethrin) were extracted and quantified by liquid chromatography with diode array detection in water samples from a wetland system used for the treatment of waste from a dog breeding plant. Response surface methodology, based on least-squares and artificial neural networks modelling, was applied for the optimization of a dispersive liquid-liquid microextraction (DLLME) procedure. Firstly, two experimental designs were built for screening and optimization, respectively. Then, the desirability function was implemented for the simultaneous optimization of the six recoveries (chromatographic areas of the six compounds). The optimum conditions were: 600 μL of acetone (dispersive solvent), 670 μL of dichloromethane (extractant solvent) and 0.6 min of vortex mixing. The preconcentration factor was 37.5. Then, in order to identify and quantify the six drugs, second-order calibration with MCR-ALS modeling of HPLC-DAD data was implemented attaining successful results. The limits of quantification were 4 ng mL^-1 for imidaclopril, albendazole and fenbendazole; 8 ng mL^-1 for praziquantel and fipronil; and 26 ng mL^-1 for permethrin. The developed method allowed the quantitation of the target analytes, even in the presence of unexpected compounds from dirty water samples. The following maximum levels of veterinary drugs were found (in ng mL^-1): imidaclopril, 7; albendazole, 46; fenbendazole, 21; praziquantel, 29; fipronil, 29 and permethrin, 217.

Quick and Sensitive Enantioselective Determination of Permethrin in Fruits and Vegetables by Combining Supramolecular Solvents and Chiral Liquid Chromatography-Tandem Mass Spectrometry

Permethrin (PM) is one of the chiral insecticides most widely used around the world. The significant differential toxicity of its four enantiomers and its important adverse effects on human health highlights the need for determination of PM enantiomers. The aim of this work was to develop the first enantioselective method for quantification of PM in fruits and vegetables. The method is based on the extraction of PM enantiomers in supramolecular solvents with restricted access properties (SUPRAS-RAM) and their separation/detection by chiral liquid chromatography-tandem mass spectrometry (LC-MS/MS) which is first reported in this article. SUPRAS-RAM-based extraction is proposed as an innovative treatment approach that drastically reduces solvent consumption and avoids the need for sample cleanup. Extraction of PM enantiomers is quick (vortexing for 5 min) and efficient (recoveries 93-107%). The method is sensitive (quantification limits from 1.0 to 1.2 μg kg^-1) and suitable for control of PM enantiomers in agri-food products.

Optimization of dispersive liquid-liquid microextraction procedure for detecting chlorpyrifos in human urine samples

Background: Selecting an effective sample preparation method to measure target pesticides in biological matrices is a serious challenge for researchers. This study aimed to optimize the dispersive liquid-liquid microextraction (DLLME) technique to obtain a simple, valid, and fast method with high efficiency to detect chlorpyrifos in urine samples. Methods: DLLME, coupled with high performance liquid chromatography equipped with ultra violet detector, was used to extract chlorpyrifos pesticide in human urine samples. Different affecting parameters on the efficiency of the method were optimized using one factor at a time method. Results: The limit of detection and enrichment factor of the method was 0.5 and 230 µg L-1, respectively. Linear calibration curve with 1-500 µg L-1 concentration range was used. The relative standard deviation (RSD) for 6 replicate experiments at the concentration of 200 µg L-1 was less than 5%. The relative recoveries of spiked urine samples were 96.3%, 102.3%, and 98.7% at 3 different concentration levels of 50, 200, and 1000 µg L-1, respectively. Conclusion: Compared to other extraction techniques, the optimized DLLME resulted in some advantages such as shorter extraction time, high extraction efficiency, and good enrichment factor for the extraction of chlorpyrifos from human urine samples.

Determination of Pyrethroids in Paris polyphylla Sample by High-Performance Liquid Chromatography Using Ultrasound-Assisted Magnetic Solid-Phase Extraction

A novel ultrasound-assisted magnetic solid-phase extraction (UA-MSPE) was developed for the separation/preconcentration of trace amounts of pyrethroids (fenpropathrin, fenvalerate, deltamethrin, and bifenthrin) in Paris polyphylla sample using carbon nanotubes based on Fe₃O₄ magnetic nanoparticles (Fe₃O₄@CNT MNPs), and high-performance liquid chromatography-UV is described. High recoveries of pyrethroids were obtained at a low MNPs concentration because sonication enhances the contact chances between magnetic nanoparticles and extractable analytes and promotes the extractability of the MSPE process. After the extraction, the adsorbent can be conveniently separated from the sample solution by an external magnet, and the adsorbed analytes were eluted from magnetic Fe₃O₄@CNT. The main factors influencing the extraction efficiency including the amount of the MNPs, the extraction time, the pH of sample solution, the sonicating time, and the desorption conditions were studied and optimized. Under the optimized experimental conditions, a good linearity was observed in the range of 1-100.0 ng mL^-1 for all the analytes, with the correlation coefficients (r) ranging from 0.9962 to 0.9991. The limits of detection of the four pyrethroids are 0.53, 0.26, 0.47, and 0.67 ng mL^-1, respectively. The recoveries of the method were in the range between 85.5% and 93.2%. This method is much faster and more effective than traditional SPE methods, and it is promising for the analysis of pyrethroids residues.

Synthesis of molecularly imprinted nanoparticles for selective exposure assessment of permethrin: optimization by response surface methodology

BACKGROUND

Extensive use of high-efficiency pyrethroid pesticides as pest-control agents lead to remarkable adsorption and release of these materials in soil and aquatic environment which could have serious adverse effects on water and food chain quality as well as human health. In this study, a molecularly imprinted polymer was synthesized and used as a selective sorbent in the sample preparation procedure in order to facilitate sensitive and quantitative exposure assessment of insecticide permethrin.

METHODS

Molecular imprinted nanoparticles were prepared by precipitation polymerization technique using 1:4:20 mmol ratio of the template, functional monomer, and cross-linker, respectively, as well as 80 mL of chloroform as progen solvent. The obtained nanoparticles were characterized by field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectrometry (FT-IR). The optimization of critical variables in the MISPE process was done using the central composite design (CCD) of the response surface methodology.

RESULTS

Quadratic regressional models were developed to correlate the response and independent variables and the analysis of variance (ANOVA) verified the excellent fitting of proposed models for experimental data. Optimum conditions for the highest MISPE yield were selected as follow: sorbent mass of 7.71 mg, sample pH 5.58 and 5.68 for cis and trans-permethrin, respectively, sample flow rate of 0.6 mL/min, as well as 5 and 3.94 mL of methanol/acetic acid at the flow rate of 2 mL/min as elution solvents for cis and trans-permethrin, respectively. Under optimized conditions, the linear range was obtained 20-120 μg/L (R2 = 0.99) and the detection limits were 5.51 and 5.72 μg/L for cis and trans-permethrin, respectively. Analysis of real samples demonstrated the high extraction efficiency of designed protocol ranging from 93.01 to 97.14 with the relative standard deviation (RSD) less than 4.51%.

CONCLUSIONS

The satisfactory results confirmed the reliability and efficiency of the proposed method for trace analysis of permethrin isomers in biological and environmental samples.

Fe3O4/hydroxyapatite/graphene quantum dots as a novel nano-sorbent for preconcentration of copper residue in Thai food ingredients: Optimization of ultrasound-assisted magnetic solid phase extraction

Fe₃O₄/hydroxyapatite/graphene quantum dots (Fe₃O₄/HAP/GQDs) nanocomposite was synthesized and used as a novel magnetic adsorbent. This nanocomposite was characterized using scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, energy dispersive X-ray spectroscopy, and magnetization property. The Fe₃O₄/HAP/GQDs was applied to pre-concentrate copper residues in Thai food ingredients (so-called "Tom Yum Kung") prior to determination by inductively coupled plasma-atomic emission spectrometry. Based on ultrasound-assisted extraction optimization, various parameters affecting the magnetic solid-phase extraction, such as solution pH, amount of magnetic nanoparticles, adsorption and desorption time, and type of elution solvent and its concentration were evaluated. Under optimal conditions, the linear range was 0.05-1500ngmL^-1 (R²>0.999), limit of detection was 0.58ngmL^-1, and limit of quantification was 1.94ngmL^-1. The precision, expressed as the relative standard deviation of the calibration curve slope (n=5), for intra-day and inter-day analyses was 0.87% and 4.47%, respectively. The recovery study of Cu for real samples was ranged between 83.5% and 104.8%. This approach gave the enrichment factor of 39.2, which guarantees trace analysis of Cu residues. Therefore, Fe₃O₄/HAP/GQDs can be a potential and suitable candidate for the pre-concentration and separation of Cu from food samples. It can easily be reused after treatment with deionized water.

In-syringe low-density ionic liquid dispersive liquid–liquid microextraction for the fast determination of pyrethroid insecticides in environmental water samples by HPLC-DAD

In-syringe low-density ionic liquid dispersive liquid–liquid microextraction.

Magnetic solid-phase extraction based on modified ferum oxides for enrichment, preconcentration, and isolation of pesticides and selected pollutants

Recently, a simple, rapid, high-efficiency, selective, and sensitive method for isolation, preconcentration, and enrichment of analytes has been developed. This new method of sample handling is based on ferum oxides as magnetic nanoparticles (MNPs) and has been used for magnetic solid-phase extraction (MSPE) of various analytes from various matrices. This review focuses on the applications of modified ferum oxides, especially modified Fe3O4 MNPs, as MSPE adsorbent for pesticide isolation from various matrices. Further perspectives on MSPE based on modified Fe3O4 for inorganic metal ions, organic compounds, and biological species from water samples are also presented. Ferum(III) oxide MNPs (Fe2O3) are also highlighted.