Spectrophotometric system based on a device created by 3D printing for the accommodation of a webcam chamber as a detection system

3D-printed device for the kinetic determination of As(III) in groundwater samples by digital movie analysis

High concentrations of inorganic arsenic in groundwater for human consumption is a worldwide common problem. Particularly, the determination of As(III) becomes important, since this species is more toxic than organic, pentavalent and elemental arsenic forms. In this work, a 3D-printed device that included a 24-well microplate was developed to perform the colourimetric kinetic determination of arsenic (III) by digital movie analysis. A smartphone camera attached to the device was used to take the movie during the process where As(III) inhibited the decolourization of methyl orange. The movie images were subsequently transformed from RGB to YIQ space to obtain a new analytical parameter called "d", which was related to the chrominance of the image. Then, this parameter allowed the determination of the inhibition time of reaction (t_in), which was linearly correlated with the concentration of As(III). A linear calibration curve (R = 0.9995) in the range from 5 μg L^-1 to 200 μg L^-1 was obtained. The method was precise (RSD = 1.2%), and the limits of detection (LOD) and quantification (LOQ) were 1.47 μg L^-1 and 4.44 μg L^-1, respectively. These values were lower than the limit established by the World Health Organization for total arsenic in drinking water (10 μg L^-1). The accuracy of the method was assessed by a recovery study with optimal results (94.3%-104.0%). Additionally, the Analytical GREEnness metric approach was applied, obtaining a score 1.7 times higher than previously published works. The method is simple, portable and low-cost, being in compliance with various principles of green analytical chemistry.

Modular 3D-printed fluorometer/photometer for determination of iron(ii), caffeine, and ciprofloxacin in pharmaceutical samples

The demand for the development of portable and low-cost analytical devices has encouraged studies employing additive manufacturing techniques, such as 3D-printing. This method can be used to produce components such as printed electrodes, photometers, and fluorometers for low-cost systems that provide advantages including low sample volume, reduced chemical waste, and easy coupling with LED-based optics and other instrumental devices. In the present work, a modular 3D-printed fluorometer/photometer was designed and applied for the determination of caffeine (CAF), ciprofloxacin (CIP), and Fe(ii) in pharmaceutical samples. All the plastic parts were printed separately by a 3D printer, using Tritan as the plastic material (black color). The final size of the modular 3D-printed device was 12 × 8 cm. The radiation sources were light-emitting diodes (LEDs), while a light dependent resistor (LDR) was used as a photodetector. The analytical curves obtained for the device were: y = 3.00 × 10^-4 [CAF] + 1.00 and R ² = 0.987 for caffeine; y = 6.90 × 10^-3 [CIP] - 3.39 × 10^-2 and R ² = 0.991 for ciprofloxacin; and y = 1.12 × 10^-1 [Fe(ii)] + 1.26 × 10^-2 and R ² = 0.998 for iron(ii). The results obtained using the developed device were compared with reference methods, with no statistically significant differences observed. The 3D-printed device was composed of moveable parts, providing flexibility for adaptation and application as a photometer or fluorometer, by only switching the photodetector position. The LED could also be easily switched, permitting application of the device for different purposes. The cost of the device, including the printing and electronic components, was lower than US$10. The use of 3D-printing enables the development of portable instruments for use in remote locations with a lack of research resources.

Development of Pipetteless Paper-Based Analytical Devices with a Volume Gauge

In this work, we propose a new design for paper-based analytical devices (PADs) that eliminate the need to use a micropipette for sample introduction. With this design, a PAD is equipped with a distance-based detection channel that is connected to a storage channel that indicates the volume of a sample introduced into the PAD. The analyte in the sample solution reacts with a colorimetric reagent deposited into the distance-based detection channel as the sample solution flows into the storage channel where the volume is measured. The ratio of the lengths of the detection channel and that of the storage channel (D/S ratio) are constant for a sample containing a certain concentration, which is independent of the introduced volume. Therefore, the PADs permit volume-independent quantification using a dropper instead of a micropipette because the length of the storage channel plays the role of a volume gauge to estimate the introduced sample volume. In this study, the D/S ratios obtained with a dropper were comparable to those obtained with a micropipette, which confirmed that precise volume control is unnecessary for this PAD system. The proposed PADs were applied to the determinations of iron and bovine serum albumin using bathophenanthroline and tetrabromophenol blue as colorimetric reagents, respectively. The calibration curves showed good linear relationships with coefficients of 0.989 for iron and 0.994 for bovine serum albumin, respectively.

Multifunctional Portable System Based on Digital Images for In-Situ Detecting of Environmental and Food Samples

The development of a portable device created by 3D printing for colorimetric and fluorometric measurements is an efficient tool for analytical applications in situ or in the laboratory presenting a wide field of applications in the environmental and food field. This device uses a light-emitting diode (LED) as radiation source and a webcam as a detector. Digital images obtained by the interaction between the radiation source and the sample were analyzed using a programming language developed in Matlab (Mathworks Inc., Natick, MA, USA), which builds the calibration curves in real-time using the RGB colour model. In addition, the entire system is connected to a notebook which serves as an LED and detector power supply without the need for any additional power source. The proposed device was used for the determination in situ of norfloxacin, allura red, and quinine in water and beverages samples, respectively. For the validation of the developed system, the results obtained were compared with a conventional spectrophotometer and spectrofluorometer respectively with a t-test at a 95% confidence level, which provides satisfactory precision and accuracy values.

Development of a versatile smartphone-based environmental analyzer (vSEA) and its application in on-site nutrient detection

The citizen-science-based environmental survey can benefit from the smartphone technology used in chemical and biological sensing of a wide range of analytes. Quantification by smartphone-based colorimetric assays is being increasingly reported, however, most of the quantification uses empirical formula or complex exhaustive methods. In this study, a versatile and robust algorithm is proposed to overcome these limitations. A model is established to simulate and analyze the conversion process from the camera's spectral information into RGB (Red, Green, Blue) color information. Moreover, the feasibility of the algorithm for the quantification of different analytes is also explored. Based on this algorithm, a versatile smartphone-based environmental analyzer (vSEA) is built and its reliability, versatility, and analytical performance are comprehensively optimized. The good linearity (R² ≥ 0.9954) and precision (relative standard deviations < 5.3%) indicates that the vSEA is accurate enough to quantify the nutrients in most natural waters. Furthermore, the vSEA is used for the field measurement of five important nutrients, and the results show no significant difference compared to conventional methods. The vSEA offers a simpler and easier method for the on-site measurement of nutrients in natural water bodies, which can aid in the emergency monitoring of aqueous ecosystems and the performance of citizen-science-based research.

A new and accessible instrumentation to determine urea in UHT milk using digital image analysis

This research demonstrates the development, optimization and application of a new low-cost detection system, based on digital image analysis, for the detection of urea in ultra-high-temperature (UHT) milk samples. The apparatus built in the laboratory, allows the capture of images through a simple system built by polyvinyl chloride (PVC) tubes, a digital microscope and a peristaltic mini-pump, after the colorimetric reaction between urea and diacetylmonoxime (butane-2,3-dionammonoxime). The red, green and blue (RGB) and hue, saturation and value (HSV) color systems were studied, with the saturation channel of the HSV color system selected as the analytical signal. Subsequently, the experimental chemical conditions were evaluated through multivariate experimental designs and the optimal conditions were defined. The proposed method was validated, and the detection and quantification limits presented by the method were 0.35 mg L^-1 and 0.52 mg L^-1, respectively; precision, ranged between 1.6  and 2.8 %. The results were compared with those obtained using the mid-infrared technique and no statistically significant differences were observed at a 95 % confidence level. The proposed method was applied to eight UHT milk samples that presented urea content ranging from 187 to 386 mg L^-1. The mean values obtained are in agreement with values presented in other studies for the determination of urea in milk. The results indicated that the system described and validated here is promising and can be applied to assess the authenticity and quality of milk.

Mesopores silica nanotubes-based sensors for the highly selective and rapid detection of Fe2+ ions in wastewater, boiler system units and biological samples

Mesopores silica nanotubes (MSNTs)-based chemical sensors for the rapid detection and of highly selective Fe²⁺ ions have been prepared. The novel nanosensors were prepared via immobilization of 1,10-phenanthroline-5-amine (PA) and bathophenanthroline (BP) onto the MSNTs. The resultant PA and BP sensors display high sensitivity for detection the Fe²⁺ ions in tap water, river water, sea water, two units in simple cycle power station, and biological samples. More interestingly, upon meeting ultra-trace amount of Fe²⁺ ions, a red complex appears at once. Color changes can be seen from the naked eye and tracked with a smartphone or spectrophotometric techniques. The response time that is necessary to achieve a stable signal was less than 15 s. The Univariate (Univar) calibration technique had been utilized for the determination of figures of merits. The detection limit obtained from the digital image analysis was 19 ppb (7.04 × 10^-7 M) for Fe²⁺ ions, while the obtained from the spectrophotometric method was 6.7 ppb (2.48 × 10^-7 M). Therefore, the two sensors had been successfully used in the determination of Fe²⁺ in several real samples with high sensitivity and selectivity. In addition, they can be used as a simple, rapid, and portable method to detect and quantify the pre rust in any cooler system.

Simple-to-use and portable device for free chlorine determination based on microwave-assisted synthesized carbon dots and smartphone images

A new portable and simple 3D printed device was designed for free chlorine determination in water samples. The analytical method was based on the quenching caused by free chlorine on the fluorescence emission of the carbon dots (CD) synthesized from citric acid and urea. The fluorescence was captured through the camera of a smartphone, which was coupled to the 3D printed device, and the images were processed using the RGB system by the ImageJ 1.51q software. The proposed method was selective and precise (RSD% 4.6, for n = 6), and the trueness of the results was evaluated by comparing the results obtained with those recovered by the spectrophotometric method 4500-Cl G (standard method), with good agreement between them. Moreover, the remarkable correlation between the CD signal and the free chlorine concentration resulted in a determination with low detection limits (limit of detection of 6 μg L^-1 and limit of quantification of 20 μg L^-1). Therefore, the new method and the related portable device could be considered a fast, economical and reliable alternative for the on-site determination of free chlorine in water samples.

Use of universal 3D-Printed smartphone spectrophotometer to develop a time-based analysis for hypochlorite

A fully-functional smartphone-based spectrophotometer was designed and built using 3D printing. The major advantage of this approach is its capacity to be interfaced with a variety of smartphones, allowing the use of the smartphone's camera and display, and regardless of the relative position of the camera. The analytical performance of the device was analyzed using a model dye (crystal violet), leading to a proportional response for concentrations in the 0.06-15.0 mg L^-1 range, with a variability of 1.0% (intra-day) and 2.6% (inter-day). To demonstrate the functionality of the device, the degradation process of the dye by sodium hypochlorite was studied. The results obtained were applied to develop a paper-based test for NaClO in sanitation solutions, in which the time required to bleach the dye was used to estimate the concentration of the solution. This device represents a simple and inexpensive tool for everyday laboratory use and could address important analytical challenges in low-income communities and features a versatile arrangement, that is compatible with a wide variety of smartphones and software platforms.

Low-cost and open-source strategies for chemical separations

In recent years, a trend toward utilizing open access resources for laboratory research has begun. Open-source design strategies for scientific hardware rely upon the use of widely available parts, especially those that can be directly printed using additive manufacturing techniques and electronic components that can be connected to low-cost microcontrollers. Open-source software eliminates the need for expensive commercial licenses and provides the opportunity to design programs for specific needs. In this review, the impact of the "open-source movement" within the field of chemical separations is described, primarily through a comprehensive look at research in this area over the past five years. Topics that are covered include general laboratory equipment, sample preparation techniques, separations-based analysis, detection strategies, electronic system control, and software for data processing. Remaining hurdles and possible opportunities for further adoption of open-source approaches in the context of these separations-related topics are also discussed.

Design of an automatic spectrophotometric system

A Multi-Syringe Flow Injection Analysis (MSFIA) fluorometric system based on a 3D printing device hosting a CCD detector has been designed for the determination of quinine in soft drinks. A LED controlled by an electronic circuit was used as a radiation source. The entire system is connected to two USB outputs of a computer. The AutoAnalysis program has been used for data acquisition and treatment. The results are more accurate and precise than those obtained with a manual method using a conventional spectrofluorometer. This developed system is a viable alternative to reduce the consumption of reagents, the impact on the environment and reduce measurement costs.

Design of a portable spectrophotometric system part II: Using a digital microscope as detector

A simple, cheap and portable spectrophotometric system is described. It is based on the use of a cheap digital microscope housed from a 3D printed device which simultaneously supports a LED as a light source and a flow cell. A simple electronic device to power the LED is also described using electronic smd components. Both the digital microscope and the power source required to light the LED are connected to the USB ports of a notebook in order to avoid the need of any power source to complete the portable system. This method was applied to make the determination of Fe²⁺ with o-phenanthroline as chromogenic reagent. The reaction provided the red complex which is used to monitor the analytical response with the digital microscope.

New, inexpensive and simple 3D printable device for nephelometric and fluorimetric determination based on smartphone sensing

A new, inexpensive and easy to use 3D printable device was developed for nephelometric and fluorimetric determination. Its applicability was tested for the quantification of quinine in tonic drinks and sulfate in natural water with good analytical accuracy. In this way, sulfate determination was carried out by nephelometry using a red LED, while quinine was determined using a blue LED by fluorimetry. A smartphone camera was used to take the pictures and afterwards transform them into the RGB color space using the software ImageJ by a personal computer. The linear range was 2.0–50.0 mg L⁻¹ for sulfate with a LOD of 0.13 mg L⁻¹, and the corresponding quantification limit (LOQ) was 0.43 mg L⁻¹. The linear range for quinine was from 0.42 to 3.10 mg L⁻¹. The LOD and LOQ were 0.11 mg L⁻¹ and 0.38 mg L⁻¹, respectively.

A new, inexpensive and easy to use 3D printable device was developed for nephelometric and fluorimetric determination.