The emerging role of 3D printing in the fabrication of detection systems

Cost-effective fully 3D-printed on-drop electrochemical sensor based on carbon black/polylactic acid: a comparative study with screen-printed sensors in food analysis

3D-printing technology allows scientist to fabricate easily electrochemical sensors. Until now, these sensors were designed employing a large amount of material, which increases the cost and decreases manufacturing throughput. In this work, a low-cost 3D-printed on-drop electrochemical sensor (3D-PES) was fully manufactured by fused filament fabrication, minimizing the number of printing layers. Carbon black/polylactic acid filament was employed, and the design and several printing parameters were optimized to yield the maximum electroanalytical performance using the minimal amount of material. Print speed and extrusion width showed a critical influence on the electroanalytical performance of 3D-PES. Under optimized conditions, the fabrication procedure offered excellent reproducibility (RSD 1.3% in working electrode diameter), speed (< 3 min/unit), and costs (< 0.01 $ in material cost). The 3D-PES was successfully applied to the determination of phloridzin in apple juice. The analytical performance of 3D-PES was compared with an equivalent commercial on-drop screen-printed electrode, yielding similar precision and accuracy but lower sensitivity. However, 3D-PES provides interesting features such as recyclability, biodegradability, low-cost, and the possibility of being manufactured near the point of need, some of which meets several demands of Green Chemistry. This cost-effective printing approach is a green and promising alternative for manufacturing disposable and portable electroanalytical devices, opening new possibilities not only in on-site food analysis but also in point-of-care testing.

3D-printed portable device for illicit drug identification based on smartphone-imaging and artificial neural networks

In this manuscript, a 3D-printed analytical device has been successfully developed to classify illicit drugs using smartphone-based colorimetry. Representative compounds of different families, including cocaine, 3,4-methylenedioxy-methamphetamine (MDMA), amphetamine and cathinone derivatives, pyrrolidine cathinones, and 3,4-methylenedioxy cathinones, have been analyzed and classified after appropriate reaction with Marquis, gallic acid, sulfuric acid, Simon and Scott reagents. A picture of the colored products was acquired using a smartphone, and the corrected RGB values were used as input data in the chemometric treatment. ANN using two active layers of nodes (6 nodes in layer 1 and 2 nodes in layer 2) with a sigmoidal transfer function and a minimum strict threshold of 0.50 identified illicit drug samples with a sensitivity higher than 83.4 % and a specificity of 100 % with limits of detection in the microgram range. The 3D printed device can operate connected to a rechargeable lithium-ion cell portable battery, is inexpensive, and requires minimal training. The analytical device has been able to discriminate the analyzed psychoactive substances from cutting and mixing agents, being a useful tool for law enforcement agents to use as a screening method.

Simultaneously performing Taylor dispersion analysis with fluorimetry, photometry, and contactless conductometry at the same detection window

Taylor dispersion analysis (TDA) is a rapid and precise method for determining the hydrodynamic radius (RH) of various substances. We present a versatile TDA system with a flow-through sample injection device, two compact 3-in-1 detectors, and a high-voltage power supply. The 3D-printed detectors combine fluorimetry (FD), photometry (AD@255 nm), and contactless conductometry (C4D) in a single head, enabling simultaneous detection at one capillary window. Using bovine serum albumin (BSA) as a model analyte, we compare TDA with different detection methods. BSA labeled with fluorescein isothiocyanate (FITC) is analyzed in both pulse mode and capillary electrophoresis (CE) TDA. FD and AD detection yield similar RH values, except when FITC binds with small ions in the buffer. In phosphate buffer, C4D underestimates RH values by approximately 18 % due to BSA self-association. In Tris-based buffers, C4D values are 87%-96 % of AD values in pulse mode. With CE-TDA using Tris-CHES buffer, no statistical difference is found across all detections. The system is also applied to CE-TDA of various compounds, particularly charged saccharides. CE-TDA improves the accuracy of TDA results from C4D. We demonstrate the resolution of mixed C4D-TDA signals with assistance from FD and AD signals, successfully resolving gluconate peaks fully covered by another compound. The versatile system with 3-in-1 detection offers a powerful tool for TDA of mixtures and enhances sample throughput.

Modulable 3D-printed plantibody-laden platform enabling microscale affinity extraction and ratiometric front-face fluorescence detection of microcystin-LR in marine waters

A 3D-printed stereolithographic platform for selective biorecognition is designed to enable convective microscale affinity extraction of microcystin-LR (MC-LR) followed by direct solid-phase optosensing exploiting ratiometric front-face fluorescence spectroscopy. For this purpose, a recombinant monoclonal plantibody (recAb) is covalently attached to a 3D-printed structure for sorptive immunoextraction, whereupon the free and unbound primary amino moieties of the recAb are derivatized with a fluorescent probe. The fluorophore-recAb-MC-LR laden device is then accommodated in the cuvette holder of a conventional fluorometer without any instrumental modification for the recording of the solid-phase fluorescence emission. Using Rodbard's four-parameter sigmoidal function, the 3D-printed bioselective platform features a limit of detection (LOD) of 28 ng L-1 using a sample volume of 500 mL, device-to-device reproducibility down to 12%, and relative recoveries ranging from 91 to 100% in marine waters. Printed prototypes are affordable, just 0.4 € per print and ≤ 10 € per device containing recAb. One of the main assets of the miniaturized immunoextraction device is that it performs comparably well in terms of analytical figures of merit with costly mass spectrometric-based analytical methodologies, such as HPLC-MS/MS. The device is readily applicable to high-matrix samples, such as seawater, as opposed to previous biosensing platforms, just applied to freshwater systems.

Enhancing the Concentration Capability of Nonsupported Electrically Driven Liquid-Phase Microextraction through Programmable Flow Using an All-In-One 3D-Printed Optosensor: A Proof of Concept

A versatile millifluidic 3D-printed inverted Y-shaped unit (3D-YSU) was prototyped to ameliorate the concentration capability of nonsupported microelectromembrane extraction (μ-EME), exploiting optosensing detection for real-time monitoring of the enriched acceptor phase (AP). Continuous forward-flow and stop-and-go flow modes of the donor phase (DP) were implemented via an automatic programmable-flow system to disrupt the electrical double layer generated at the DP/organic phase (OP) interface while replenishing the potentially depleted layers of analyte in DP. To further improve the enrichment factor (EF), the organic holding section of the OP/AP channel was bifurcated to increase the interfacial contact area between the DP and the OP. Exploiting the synergistic assets of (i) the continuous forward-flow of DP (1050 μL), (ii) the unique 3D-printed cone-shaped pentagon cross-sectional geometry of the OP/AP channel, (iii) the bifurcation of the OP that creates an inverted Y-shape configuration, and (iv) the in situ optosensing of the AP, a ca. 24 EF was obtained for a 20 min extraction using methylene blue (MB) as a model analyte. The 3D-YSU was leveraged for the unsupervised μ-EME and the determination of MB in textile dye and urban wastewater samples, with relative recoveries ≥88%. This is the first work toward analyte preconcentration in μ-EME with in situ optosensing of the resulting extracts using 3D-printed millifluidic platforms.

Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer

Electrochemical (EC) detection is a powerful tool supporting simple, low-cost, and rapid analysis. Although screen printing is commonly used to mass fabricate disposable EC chips, its mask is relatively expensive. In this research, we demonstrated a method for fabricating three-electrode EC chips using 3D printing of relatively high-viscosity paste. The electrodes consisted of two layers, with carbon paste printed over silver/silver chloride paste, and the printed EC chips were baked at 70 °C for 1 h. Engineering challenges such as bulging of the tubing, clogging of the nozzle, dripping, and local accumulation of paste were solved by material selection for the tube and nozzle, and process optimization in 3D printing. The EC chips demonstrated good reversibility in redox reactions through cyclic voltammetry tests, and reliably detected heavy metal ions Pb(II) and Cd(II) in solutions using differential pulse anodic stripping voltammetry measurements. The results indicate that by optimizing the 3D printing of paste, EC chips can be obtained by maskless and flexible 3D printing techniques in lieu of screen printing.

A review of the recent achievements and future trends on 3D printed microfluidic devices for bioanalytical applications

3D printing has revolutionized the manufacturing process of microanalytical devices by enabling the automated production of customized objects. This technology promises to become a fundamental tool, accelerating investigations in critical areas of health, food, and environmental sciences. This microfabrication technology can be easily disseminated among users to produce further and provide analytical data to an interconnected network towards the Internet of Things, as 3D printers enable automated, reproducible, low-cost, and easy fabrication of microanalytical devices in a single step. New functional materials are being investigated for one-step fabrication of highly complex 3D printed parts using photocurable resins. However, they are not yet widely used to fabricate microfluidic devices. This is likely the critical step towards easy and automated fabrication of sophisticated, complex, and functional 3D-printed microchips. Accordingly, this review covers recent advances in the development of 3D-printed microfluidic devices for point-of-care (POC) or bioanalytical applications such as nucleic acid amplification assays, immunoassays, cell and biomarker analysis and organs-on-a-chip. Finally, we discuss the future implications of this technology and highlight the challenges in researching and developing appropriate materials and manufacturing techniques to enable the production of 3D-printed microfluidic analytical devices in a single step.

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples

BACKGROUND

There is a quest of novel functional and reliable platforms for enhancing the efficiency of microextraction approaches in troublesome matrices, such as industrial wastewaters. 3D printing has been proven superb in the analytical field to act as the springboard of microscale extraction approaches.

RESULTS

In this work, low-force stereolithography (SL) was exploited for 3D printing and prototyping bespoke fluidic devices for accommodating nonsupported microelectromembrane extraction (μEME). The analytical performance of 3D-printed μEME devices with distinct cross-sections, including square, circle, and obround, and various channel dimensions was explored against that of commonly used circular polytetrafluoroethylene (PTFE) tubing in flow injection systems. A computer-controlled millifluidic system was harnessed for the (i) automatic liquid-handling of minute volumes of donor, acceptor, and organic phases at the low μL level that spanned from 3 to 44 μL in this work, (ii) formation of three-phase μEME, (iii) in-line extraction, (iv) flow-through optical detection of the acceptor phase, and (v) solvent removal and regeneration of the μEME device and fluidic lines. Using methylene blue (MB) as a model analyte, experimental results evinced that the 3D-printed channels with an obround cross-section (2.5 mm × 2.5 mm) were the most efficient in terms of absolute extraction recovery (59%), as compared to PTFE tubing of 2.5 mm inner diameter (27%). This is attributed to the distinctive convex interface of the organic phase (1-octanol), with a more pronounced laminar pattern, in 3D-printed SL methacrylate-based fluidic channels against that of PTFE tubing on account of the enhanced 1-octanol wettability and lower contact angles for the 3D-printed devices. The devices with obround channels were leveraged for the automatic μEME and in-line clean-up of MB in high matrix textile dyeing wastewater samples with relative recoveries ≥81%, RSD% ≤ 17.1% and LOD of 1.3 mg L-1. The 3D-printed nonsupported μEME device was proven superb for the analysis of wastewater samples with an elevated ionic strength (0.7 mol L-1 NaCl, 5000 mg L-1 Na2CO3, and 0.013 mol L-1 NaOH) with recorded electric currents below 12 μA.

NOVELTY

The coupling of 3D printing with nonsupported μEME in automatic flow-based systems is herein proposed for the first time and demonstrated for the clean-up of troublesome samples, such as wastewaters.

4D-Printed Elution-Peak-Guided Dual-Responsive Monolithic Packing for the Solid-Phase Extraction of Metal Ions

Four-dimensional printing (4DP) technologies are revolutionizing the fabrication of stimuli-responsive devices. To advance the analytical performance of conventional solid-phase extraction (SPE) devices using 4DP technology, in this study, we employed N-isopropylacrylamide (NIPAM)-incorporated photocurable resins and digital light processing three-dimensional printing to fabricate an SPE column with a [H+]/temperature dual-responsive monolithic packing stacked as interlacing cuboids to extract Mn, Co, Ni, Cu, Zn, Cd, and Pb ions. When these metal ions were eluted using 0.5% HNO3 solution as the eluent at a temperature below the lower critical solution temperature of polyNIPAM, the monolithic packing swelled owing to its hydrophilic/hydrophobic transition and electrostatic repulsion among the protonated units of polyNIPAM. These effects resulted in smaller interstitial volumes among these interlacing cuboids and improvements in the elution peak profiles of the metal ions, which, in turn, demonstrated the reduced method detection limits (MDLs; range, 0.2-7.2 ng L-1) during analysis using inductively coupled plasma mass spectrometry. We studied the effects of optimizing the elution peak profiles of the metal ions on the analytical performance of this method and validated its reliability and applicability by analyzing the metal ions in reference materials (CASS-4, SLRS-5, 1643f, and Seronorm Trace Elements Urine L-2) and performing spike analyses of seawater, groundwater, river water, and human urine samples. Our results suggest that this 4D-printed elution-peak-guided dual-responsive monolithic packing enables lower MDLs when packed in an SPE column to facilitate the analyses of the metal ions in complex real samples.

Novel disposable and portable 3D-printed electrochemical apparatus for fast and selective screening of 25E-NBOH in forensic samples

The advent of new psychoactive substances (NPS) has caused enormous difficulty for legal control since they are rapidly commercialized, and their chemical structures are routinely altered. In this aspect, derivatives phenethylamines, such as 25E-NBOH, have received great attention in the forensic scenario. Hence, we propose portable and cost-effective (U$ 5.00) 3D-printed devices for the electrochemical screening of 25E-NBOH for the first time. The cell and all electrodes were printed using acrylonitrile butadiene styrene filament (insulating material) and conductive filament (graphite embedded in a polylactic acid matrix), respectively, both by the fused deposition modeling (FDM) 3D printing technique. The electrochemical apparatus enables micro-volume analysis (50-2000 μL), especially important for low sample volumes. A mechanistic route for the electrochemical oxidation of 25E-NBOH is proposed based on cyclic voltammetric data, which showed two oxidation processes around +0.75 V and +1.00 V and a redox pair between +0.2 and -0.2 V (vs. graphite ink pseudo-reference). A fast and sensitive square-wave voltammetry method was developed, which exhibited a linear working range from 0.85 to 5.1 μmoL-1, detection limit of 0.2 μmol L-1, and good intra-electrode precision (n = 10, RSD <5.3 %). Inter-electrode measurements (n = 3, RSD <9.8 %) also attested that the electrode production process is reproducible. Interference tests in the presence of other drugs frequently found in blotting paper indicated high selectivity of the electrochemical method for screening of 25E-NBOH. Screening analysis of blotting paper confirmed the presence of 25E-NBOH in the seized samples. Moreover, a recovery percentage close to 100 % was found for a spiked saliva sample, suggesting the method's usefulness for quantitative purposes aimed at information on recent drug use.

Research progress of All-in-One PCR tube biosensors based on functional modification and intelligent fabrication

PCR amplification technology is the cornerstone of molecular biology. All-in-One PCR tube, as an emerging integrated device, is booming in biosensors application. All-in-One PCR tube biosensors are integrated PCR tubes designed for signal recognition, signal amplification or signal output. They enable "one-pot" detection within functionally modified and intelligently fabricated PCR tubes, effectively overcoming the limitations of conventional PCR applications, like complex procedural steps, risk of contamination and so on. Based on this, the review article summarizes the recent advance of All-in-One PCR tube biosensors for the first time as well as systematically categorizes five approaches of functional modification, three types of intelligent fabrication and relevant property characterization techniques. More emphasis is placed on the review of five ways of functional modification, including physical modification, chemical modification, UV photografting surface treatment, plasma surface modification, and layer-by-layer assembly coating. Moreover, All-in-One PCR tube biosensors covering different recognition elements range from small molecules to protein are detailed discussed on principle of sensing, providing a deeper understanding of the design and application of All-in-One-tube biosensor. Last, the future opportunities and challenges in this fascinating field are also deliberated.

A new adsorptive 3D-printed sampling device for simultaneous determination of 63 urinary organic acids by LC-MS/MS

BACKGROUND

The detection and quantification of urinary metabolites play an important role in disease diagnosis. In most cases, urinary analyses are done with liquid urine samples, which must be quickly transported to the laboratory to avoid metabolites degradation that is associated with temperature fluctuations. Consequently, dried sampling devices have emerged to minimize analyte degradation. However, most commercial dried sampling devices are expensive, aggregate low volumes, and need better analytical sensitivity. Therefore, a new dry urine sampling device that is inexpensive, suitable for domestic sampling operation, and efficient for quantifying metabolites without requiring high-resolution instruments is proposed in the present study.

RESULTS

The newly designed dry urine sampling device was produced by 3D printing that efficiently determines 63 urinary organic acids using liquid chromatography coupled with mass spectrometry (LC-MS/MS). The system's efficiency was demonstrated with analytical figures of merit, such as precision, accuracy, and stability of analytes after the sampling and storing of ordinary urine samples. The limits of quantification ranged from 0.01 to 0.42 ng mL-1. Precision and accuracy tests showed relative standard deviations of less than 15 %. The urine stability in the sampling device was high within seven days without any significant degradation of the metabolites. The method was applied to the analysis of 10 human urine samples and compared to a conventional method without the use of the sampling device. The results showed no statistically significant differences, demonstrating the method's efficiency.

SIGNIFICANCE

The proposed 3-D printing device was developed with fast, low-cost manufacturing features and can be manufactured with different volumetric capacities, adaptable to the needs of each user. Furthermore, it is innovative because this is the first sampling device that is effective for the simultaneous storage and preservation of several important urinary metabolites. Thus, it is anticipated that its application would contribute significantly to the identification of metabolic disorders.

Compact contactless conductometric, ultraviolet photometric and dual-detection cells for capillary electrophoresis via additive manufacturing

The growing demand for tailored detectors in capillary electrophoresis (CE), addressing tasks like field deployment or dual-detection analysis, emphasizes the necessity for compact detection cells. In this work, we propose cost-effective and user-friendly additive manufacturing (3D-printing) approaches to produce such miniaturized detection cells suitable for a range of CE applications. Firstly, capacitively-coupled contactless conductivity detection (C4D) cells of different sizes are fabricated by casting low-melting-point alloy into 3D-printed molds. Various designs of Faraday shields are integrated within the cells and compared. A mini-C4D cell (9.5×7.0×7.5 mm3) is produced, with limits of detection for alkaline cations ranging from 8-12 μM in a short-capillary based CE application. Secondly, ultraviolet photometric (UV-PD) detection cells are fabricated using 3D printing. These cells feature two narrow slits with a width of 60 μm, which are positioned along the path of incident and transmission light to facilitate collimation. A deep UV-LED (235 nm or 255 nm) is employed as the light source, and black resin is determined to be the optimal material for 3D printing the UV-PD cell, owing to its superior UV light absorption capabilities. The UV-PD cell is connected to the LED and photodetector through two optical fibers, making it easy to switch the light source and detector. The effective pathlength and stray light percentage for detecting on a 75 μm id capillary are 74 μm and 0.5 %, respectively. Thirdly, a dual-detection cell that combined C4D and UV-PD at a single detection point is proposed. The performance of direct detection by C4D and indirect detection by UV-PD is compared for detecting organic acids. The strategies for developing cost-effective compact detection cells facilitate the versatile integration of multiple detection methods in CE analysis.

3D Printed Lattice Template by Material Extrusion Technique for Fabrication of Pixelated Photodetector

Rigid and flexible, pixelated ultraviolet photodetectors (PD) based on ZnO have been fabricated by material extrusion 3D printing technique. The photoresponse is studied in an out-of-plane configuration. An open lattice structure is printed using PLA over ITO/Glass substrate for rigid, and TPU over ITO/PET substrate for flexible PDs. ZnO slurry is filled selectively into the columnar matrix by the microdispensing technique. The optical detector printed on ITO/Glass substrate shows a sensitivity of 25 and responsivity of 1.55 nA/mW with a rise and decay time of 1.6 and 0.6 s, respectively. Similarly, the flexible PD printed using TPU lattice shows a sensitivity of 9.5 and responsivity of 0.38 nA/mW with a rise and decay time of 1.8 and 0.6 s, respectively. The charge transport mechanism is studied using band diagram analysis. 3D printed open lattice structure is found to be a potential template for sensor fabrication. This work demonstrates the capability of material extrusion 3D printing with an open lattice structure for the fabrication of high-resolution pixelated PDs.

Application of three-dimensional printing technology in environmental analysis: A review

The development of environmental analysis devices with high performance is essential to assess the potential risks of environmental pollutants. However, it is still challenging to develop environmental analysis equipment with miniaturization, portability, and high sensitivity based on traditional processing techniques. In recent years, the popularity of 3D printing technology (3DP) with high precision, low cost, and unlimited design freedom has provided opportunities to solve the existing challenges of environmental analysis. 3D printing has brought solutions to promote the high performance and versatility of environmental analysis equipment by optimizing printing materials, enhancing equipment structure, and integrating multidisciplinary technology. In this paper, we comprehensively review the latest progress in 3D printing in various aspects of environmental analysis procedures, including but not limited to sample collection, pretreatment, separation, and detection. We highlight their advantages and challenges in determining various environmental contaminants through passive sampling, solid-phase extraction, chromatographic separation, and mass spectrometry detection. The manufacturing of 3D-printed environmental analysis devices is also discussed. Finally, we look forward to their development prospects and challenges.

A novel 3D-printed graphite/polylactic acid sensor for the electrochemical determination of 2,4,6-trinitrotoluene residues in environmental waters

Here, lab-made graphite and polylactic acid (Gpt-PLA) biocomposite materials were used to additively manufacture electrodes via the fused deposition modeling (FDM) technique for subsequent determination of the explosive 2,4,6-trinitrotoluene (TNT, considered a persistent organic pollutant). The surface of the 3D-printed material was characterized by SEM and Raman, which revealed high roughness and the presence of defects in the graphite structure, which enhanced the electrochemical response of TNT. The 3D-printed Gpt-PLA electrode coupled to square wave voltammetry (SWV) showed suitable performance for fastly determining the explosive residues (around 7 s). Two reduction processes at around -0.22 V and -0.36 V were selected for TNT detection, with linear ranges between 1.0 and 10.0 μM. Moreover, detection limits of 0.52 and 0.66 μM were achieved for both reduction steps. The proposed method was applied to determine TNT in different environmental water samples (tap water, river water, and seawater) without a dilution step (direct analysis). Recovery values between 98 and 106% confirmed the accuracy of the analyses. Additionally, adequate selectivity was achieved even in the presence of other explosives commonly used by military agencies, metallic ions commonly found in water, and also some electroactive camouflage species. Such results indicate that the proposed device is promising to quantify TNT residues in environmental samples, a viable on-site analysis strategy.

4D-printed needle panel meters coupled with enzymatic derivatization for reading urea and glucose concentrations in biological samples

On-site analytical techniques continue being developed with advances in modern technology. To demonstrate the applicability of four-dimensional printing (4DP) technologies in the direct fabrication of stimuli-responsive analytical devices for on-site determination of urea and glucose, we used digital light processing three-dimensional printing (3DP) and 2-carboxyethyl acrylate (CEA)-incorporated photocurable resins to fabricate all-in-one needle panel meters. When adding a sample having a value of pH above the pKa of CEA (ca. 4.6-5.0) into the fabricated needle panel meter, the [H+]-responsive layer of the needle, printed using the CEA-incorporated photocurable resins, swelled as a result of electrostatic repulsion among the dissociated carboxyl groups of the copolymer, leading to [H+]-dependent bending of the needle. When coupled with a derivatization reaction (urease-mediated hydrolysis of urea to decrease [H+]; glucose oxidase-mediated oxidization of glucose to increase [H+]), the bending of the needle allowed reliable quantification of urea or glucose when referencing pre-calibrated concentration scales. After method optimization, the method's detection limits for urea and glucose were 4.9 and 7.0 μM, respectively, within a working concentration range from 0.1 to 10 mM. We verified the reliability of this analytical method by determining the concentrations of urea and glucose in samples of human urine, fetal bovine serum, and rat plasma with spike analyses and comparing the results with those obtained using commercial assay kits. Our results confirm that 4DP technologies can allow the direct fabrication of stimuli-responsive devices for quantitative chemical analysis, and that they can advance the development and applicability of 3DP-enabling analytical methods.

Electrochemical Determination of the Drug Colchicine in Pharmaceutical and Βiological Samples Using a 3D-Printed Device

In this work, a simple, fast, and sensitive voltammetric method for the trace determination of the alkaloid drug colchicine (Colc) using a 3D-printed device is described. The electrochemical method was based on the adsorptive accumulation of the drug at a carbon-black polylactic acid (CB/PLA) working electrode, followed by voltammetric determination of the accumulated species. The plastic sensor was printed in a single step by a low-cost dual extruder 3D-printer and featured three CB/PLA electrodes (serving as working, reference, and counter electrodes) and a holder, printed from a non-conductive PLA filament. The electrochemical parameters that affected the response of the device towards Colc determination, such as accumulation time and potential, solution pH, and other variables, were optimized. Under the selected conditions, the oxidation current of Colc was proportional to the concentration of Colc, and its quantification was conducted in the concentration range of 0.6-2.2 μmol L^-1 with a limit of detection of 0.11 μmol L^-1 in phosphate buffer (pH 7.0). Both within-device and between-device reproducibility were lower than 9%, revealing satisfactory operational and fabrication reproducibility. Furthermore, the 3D-printed device was employed for the voltammetric determination of Colc in pharmaceutical tablets and in human urine with satisfactory results, justifying its suitability for low-cost routine analysis of Colc.

3D-printed electrochemical glucose device with integrated Fe(II)-MOF nanozyme

Estimation of glucose (GLU) levels in the human organism is very important in the diagnosis and monitoring of diabetes. Scientific advances in nanomaterials have led to the construction of new generations of enzymatic-free GLU sensors. In this work, an innovative 3D-printed device modified with a water-stable and non-toxic metal-organic framework of iron (Fe(II)-MOF), which serves as a nanozyme, has been developed for the voltammetric determination of GLU in artificial sweat. In contrast to existing MOF-based GLU sensors which exhibit electrocatalytic activity for the oxidation of GLU in alkaline media, the nanozyme Fe(II)-MOF/3D-printed device can operate in the acidic epidermal sweat environment. The enzymatic-free GLU sensor is composed of a 3-electrode 3D-printed device with the MOF nanozyme immobilized on the surface of the working electrode. GLU sensing is conducted by differential pulse voltammetry without interference from other co-existing metabolites in artificial sweat. The response is based on the oxidation of glucose to gluconolactone, induced by the redox activity of the Fe-centers of the MOF. GLU gives rise to an easily detectable and well-defined voltammetric peak at about - 1.2 V and the limit of detection is 17.6 μmol L-1. The synergy of a nanozyme with 3D printing technology results in an advanced, sensitive, and low-cost sensor, paving the way for on-skin applications.

3D printed opto-microfluidic autonomous analyzer for photometric applications

3D printed opto-microfluidic autonomous analyzer for photometric applications performs the automation of analytical micro-processes. The proposed device was designed under restrictions of small size and low energy consumption, which allow its portability for in-situ, on line and real time analysis. The autonomous process and auto-calibration consists of four functions: control and data acquisition; hydrodynamic: fluid pumping and flow injection; optical detection and wireless communication. All electronics systems where controlled with a virtual instrument interface. In the experiments carried out to measure fluorides, the results obtained were very close to those obtained with laboratory equipment. The consumption of reagents was 50% less and waste was reduced by 80%. The cost of the portable and autonomous microanalyzer is 75% less than large and robust laboratory equipment.

Past, current, and future roles of 3D printing in the development of capillary electrophoresis systems

3D printing, an additive manufacturing technology, has made significant inroads into improving systems for bioanalysis in recent years. This approach is particularly powerful due to the ease and flexibility in rapidly creating novel and complex designs for analytical applications. As such, 3D printing offers an emerging technology for creating systems for electrophoretic analysis. Here, we review 3D printing work on improving and miniaturizing capillary electrophoresis (CE), emphasizing publications from 2019‒2022. We describe enabling uses of 3D printing in interfacing upstream sample preparation or downstream detection with CE. Recent developments in miniaturized CE enabled by 3D printing are also elaborated, including key areas where 3D printing could further improve over the current state-of-the-art. Lastly, we highlight promising future trends for using 3D printing in miniaturizing CE and the significant potential for innovative advancements. 3D printing is poised to play a key role in moving forward miniaturized CE in the coming years.

3D-printed chemiluminescence flow cells with customized cross-section geometry for enhanced analytical performance

Low force stereolithography is exploited for the first time for one-step facile fabrication of chemiluminescence (CL) flow-through cells that bear unrivalled features as compared to those available through milling or blowing procedures or alternative 3D printing technologies. A variety of bespoke cross-section geometries with polyhedral features (namely, triangular, square, and five-side polygon) as well as semicircular cross-section are herein critically evaluated in terms of analytical performance against the standardcircular cross-section in a flat spirally-shape format. The idea behind is to maximize capture of elicited light by the new designs while leveraging 3D printing further for fabrication of (i) customized gaskets that enable reliable attaching of the active mixing zone of the CL cell to the detection window, (ii) in-line 3D-printed serpentine reactors, and (iii) flow confluences with tailorable shapes for enhancing mixing of samples with CL reagents. Up to twenty transparent functional cells were simultaneously fabricated without inner supports following post-curing and surface treatment protocols lasting less than 5 h. In fact, previous attempts to print spirally-shaped cells in one-step by resorting to less cost effective photopolymer inkjet printing technologies were unsuccessful because of the requirement of lengthy procedures (>15 days) for quantitative removal of the support material. By exploiting the phthalazinedione-hydrogen peroxide chemistry as a model reaction, the five-side irregular pentagon cell exhibited superior analytical figures of merit in terms of LOD, dynamic range and intermediate precision as compared to alternative designs. Computational fluid dynamic simulations for mapping velocities at the entry region of the spiral cell corroborated the fact that the 5-side polygon cross-section flow-cell with Y-type confluence permitted the most efficient mixing of reagents and sample while enabling larger flow velocities near the inlet that contribute to a more efficient capture of the photons from the flash-type reaction. The applicability of the 3D-printed 5-side polygon CL cell for automatic determination of hydrogen peroxide using a computerized hybrid flow system was demonstrated for the analysis of high matrix samples, viz., seawater and saliva, with relative recoveries ranging from 83 to 103%.

Carbon Black Integrated Polylactic Acid Electrodes Obtained by Fused Deposition Modeling: A Powerful Tool for Sensing of Sulfanilamide Residues in Honey Samples

Sulfanilamide (SFL) is used to prevent infections in honeybees. However, many regulatory agencies prohibit or establish maximum levels of SFL residues in honey samples. Hence, we developed a low-cost and portable electrochemical method for SFL detection using a disposable device produced through 3D printing technology. In the proposed approach, the working electrode was printed using a conductive filament based on carbon black and polylactic acid and it was associated with square wave voltammetry (SWV). Under optimized SWV parameters, linear concentration ranges (1-10 μmol L^-1 and 12.5-35.0 μmol L^-1), a detection limit of 0.26 μmol L^-1 (0.05 mg L^-1), and suitable RSD values (2.4% for inter-electrode; n = 3) were achieved. The developed method was selective in relation to other antibiotics applied in honey samples, requiring only dilution in the electrolyte. The recovery values (85-120%) obtained by SWV were statistically similar (95% confidence level) to those obtained by HPLC, attesting to the accuracy of the analysis and the absence of matrix interference.

Three-in-One Detector by 3D Printing: Simultaneous Contactless Conductivity, Ultraviolet Absorbance, and Laser-Induced Fluorescence Measurements for Capillary Electrophoresis

We describe a 3-in-1 detector for simultaneous contactless conductivity (C⁴D), ultraviolet absorbance (UV-AD), and laser-induced fluorescence (LIF) measurements on a single detection point for capillary electrophoresis (CE). A key component of the detector was a rectangular detector head that was assembled with four 3D-printed parts. Two parts covering the detector head to function as a Faraday cage were fused deposition modeling printed using an electrically conductive material. The other two parts in between the conductive parts were stereolithography (SLA) printed with high-resolution (50 μm) constructions on the surface. After assembling the two SLA printed parts, several cavities were built with the surface constructions. Two electrodes and a Faraday shield for C⁴D were cast by injecting molten Wood's metal into the cavities. For UV-AD, a slit (100 μm width) was created by putting together two grooves (50 μm depth) on the surface of the SLA printed parts. A 255 nm UV-LED was used as the light source. The effective path length and stray light for a 50 μm id capillary were 39 μm and 13%, which were superior to those of other reported 3D-printed AD detectors. Confocal LIF detection was conducted by using an objective lens to focus the laser on the capillary via a through-hole. The detector was used to detect model analytes, including inorganic and organic ions, and fluorescein isothiocyanate labeled amino acids in a signal-run CE separation. In detecting fluorescein, LODs were 1.3 μM (C⁴D), 2.0 μM (UV-AD), and 1 nM (LIF). The calibration ranges covered from 0.01 μM to 500 μM.

3D-printed sensor decorated with nanomaterials by CO2 laser ablation and electrochemical treatment for non-enzymatic tyrosine detection

The combination of CO₂ laser ablation and electrochemical surface treatments is demonstrated to improve the electrochemical performance of carbon black/polylactic acid (CB/PLA) 3D-printed electrodes through the growth of flower-like Na₂O nanostructures on their surface. Scanning electron microscopy images revealed that the combination of treatments ablated the electrode's polymeric layer, exposing a porous surface where Na₂O flower-like nanostructures were formed. The electrochemical performance of the fabricated electrodes was measured by the reversibility of the ferri/ferrocyanide redox couple presenting a significantly improved performance compared with electrodes treated by only one of the steps. Electrodes treated by the combined method also showed a better electrochemical response for tyrosine oxidation. These electrodes were used as a non-enzymatic tyrosine sensor for quantification in human urine samples. Two fortified urine samples were analyzed, and the recovery values were 106 and 109%. The LOD and LOQ for tyrosine determination were 0.25 and 0.83 μmol L^-1, respectively, demonstrating that the proposed devices are suitable sensors for analyses of biological samples, even at low analyte concentrations.

3D Printed Voltammetric Sensor Modified with an Fe(III)-Cluster for the Enzyme-Free Determination of Glucose in Sweat

In this work, a 3D printed sensor modified with a water-stable complex of Fe(III) basic benzoate is presented for the voltammetric detection of glucose (GLU) in acidic epidermal skin conditions. The GLU sensor was produced by the drop-casting of Fe(III)-cluster ethanolic mixture on the surface of a 3D printed electrode fabricated by a carbon black loaded polylactic acid filament. The oxidation of GLU was electrocatalyzed by Fe(III), which was electrochemically generated in-situ by the Fe(III)-cluster precursor. The GLU determination was carried out by differential pulse voltammetry without the interference from common electroactive metabolites presented in sweat (such as urea, uric acid, and lactic acid), offering a limit of detection of 4.3 μmol L-1. The exceptional electrochemical performance of [Fe3O(PhCO2)6(H2O)3]∙PhCO2 combined with 3D printing technology forms an innovative and low-cost enzyme-free sensor suitable for noninvasive applications, opening the way for integrated 3D printed wearable biodevices.

3D-printed electrochemical platform with multi-purpose carbon black sensing electrodes

The 3D printing is described of a complete and portable system comprising a batch injection analysis (BIA) cell and an electrochemical platform with eight sensing electrodes. Both BIA and electrochemical cells were printed within 3.4 h using a multimaterial printer equipped with insulating, flexible, and conductive filaments at cost of ca. ~ U$ 1.2 per unit, and their integration was based on a threadable assembling without commercial component requirements. Printed electrodes were exposed to electrochemical/Fenton pre-treatments to improve the sensitivity. Scanning electron microscopy and electrochemical impedance spectroscopy measurements upon printed materials revealed high-fidelity 3D features (90 to 98%) and fast heterogeneous rate constants ((1.5 ± 0.1) × 10⁻³ cm s⁻¹). Operational parameters of BIA cell were optimized using a redox probe composed of [Fe(CN)₆]^4−/3− under stirring and the best analytical performance was achieved using a dispensing rate of 9.0 µL s⁻¹ and an injection volume of 2.0 µL. The proof of concept of the printed device for bioanalytical applications was evaluated using adrenaline (ADR) as target analyte and its redox activities were carefully evaluated through different voltammetric techniques upon multiple 3D-printed electrodes. The coupling of BIA system with amperometric detection ensured fast responses with well-defined peak width related to the oxidation of ADR applying a potential of 0.4 V vs Ag. The fully 3D-printed system provided suitable analytical performance in terms of repeatability and reproducibility (RSD ≤ 6%), linear concentration range (5 to 40 µmol L⁻¹; R² = 0.99), limit of detection (0.61 µmol L⁻¹), and high analytical frequency (494 ± 13 h⁻¹). Lastly, artificial urine samples were spiked with ADR solutions at three different concentration levels and the obtained recovery values ranged from 87 to 118%, thus demonstrating potentiality for biological fluid analysis. Based on the analytical performance, the complete device fully printed through additive manufacturing technology emerges as powerful, inexpensive, and portable tool for electroanalytical applications involving biologically relevant compounds.

3D printed spinning cup-shaped device for immunoaffinity solid-phase extraction of diclofenac in wastewaters

This article reports current research efforts towards designing bespoke microscale extraction approaches exploiting the versatility of 3D printing for fast prototyping of novel geometries of sorptive devices. This is demonstrated via the so-called 3D printed spinning cup-based platform for immunoextraction of emerging contaminants using diclofenac as a model analyte. A new format of rotating cylindrical scaffold (containing a semispherical upper cavity) with enhanced coverage of biorecognition elements, and providing elevated enhancement factors with no need of eluate processing as compared with other microextraction stirring units is proposed. Two distinct synthetic routes capitalized upon modification of the acrylate surface of stereolithographic 3D printed parts with hexamethylenediamine or branched polyethyleneimine chemistries were assayed for covalent binding of monoclonal diclofenac antibody.

Under the optimized experimental conditions, a LOD of 108 ng L⁻¹ diclofenac, dynamic linear range of 0.4–1,500 µg L^–1, and enrichment factors > 83 (for near-exhaustive extraction) were obtained using liquid chromatography coupled with UV–Vis detection. The feasibility of the antibody-laden device for handling of complex samples was demonstrated with the analysis of raw influent wastewaters with relative recoveries ranging from 102 to 109%. By exploiting stereolithographic 3D printing, up to 36 midget devices were fabricated in a single run with an estimated cost of mere 0.68 euros per 3D print and up to 16 €/device after the incorporation of the monoclonal antibody.

Electrochemical (Bio)Sensors Enabled by Fused Deposition Modeling-Based 3D Printing: A Guide to Selecting Designs, Printing Parameters, and Post-Treatment Protocols

The 3D printing (or additive manufacturing, AM) technology is capable to provide a quick and easy production of objects with freedom of design, reducing waste generation. Among the AM techniques, fused deposition modeling (FDM) has been highlighted due to its affordability, scalability, and possibility of processing an extensive range of materials (thermoplastics, composites, biobased materials, etc.). The possibility of obtaining electrochemical cells, arrays, pieces, and more recently, electrodes, exactly according to the demand, in varied shapes and sizes, and employing the desired materials has made from 3D printing technology an indispensable tool in electroanalysis. In this regard, the obtention of an FDM 3D printer has great advantages for electroanalytical laboratories, and its use is relatively simple. Some care has to be taken to aid the user to take advantage of the great potential of this technology, avoiding problems such as solution leakages, very common in 3D printed cells, providing well-sealed objects, with high quality. In this sense, herein, we present a complete protocol regarding the use of FDM 3D printers for the fabrication of complete electrochemical systems, including (bio)sensors, and how to improve the quality of the obtained systems. A guide from the initial printing stages, regarding the design and structure obtention, to the final application, including the improvement of obtained 3D printed electrodes for different purposes, is provided here. Thus, this protocol can provide great perspectives and alternatives for 3D printing in electroanalysis and aid the user to understand and solve several problems with the use of this technology in this field.

A handheld multifunctional smartphone platform integrated with 3D printing portable device: On-site evaluation for glutathione and azodicarbonamide with machine learning

Azodicarbonamide (ADA) in flour can be easily decomposed to semi-carbazide and biuret, exhibiting strong genotoxicity in vitro and carcinogenicity. Glutathione (GSH) can be conjugated with some ketone-containing compounds and unsaturated aldehydes to form toxic metabolites. Here, a novel ratio fluorescence probe based on blue emitting biomass-derived carbon dots (BCDs) and yellow emitting 2,3-diaminophenazine (OxOPD) was prepared for the bifunctional determination of glutathione (GSH) and ADA. This strategy includes three processes: (1) Ag⁺ oxidizes o-phenylenediamine (OPD) to produce OxOPD. The peak at 562 nm was enhanced, and the peak at 442 nm was reduced due to fluorescence resonance energy transfer (FRET), (2) glutathione binds Ag⁺ and inhibits the production of OxOPD, (3) ADA oxidizes GSH to form GSSG, resulting in the release of Ag⁺ by GSH. Therefore, the newly designed ratio fluorescence probe can be based on the intensity ratio (I₄₄₂/I₅₆₂) changes and significant fluorescent color changes to detect GSH and ADA. Moreover, a smartphone WeChat applet and a yolov3-assisted deep learning classification model have been developed to quickly detect GSH and ADA on-site based on an image processing algorithm. These results indicate that smartphone ratiometric fluorescence sensing combined with machine learning has broad prospects for biomedical analysis.

Portable stirring device for the on-site extraction of environmental waters using magnetic hydrophilic-lipophilic balance tape

The spatial heterogeneity of environmental systems makes sampling at multiple locations crucial to provide complete and representative information. The on-site application of an extraction technique simplifies the sampling logistics, increasing sample integrity during transportation and storage. This article presents a portable, simple, and low-cost device capable of performing the simultaneous on-site extraction of several environmental water samples. The device consists of a small electric motor integrated into the plastic cap of a conventional glass bottle and operated with a portable battery. The electric motor provides stirring to a novel magnetic sorptive phase based on the deposition of hydrophilic-lipophilic balance (HLB) particles over a magnetic tape. The use of open technology makes the device globally affordable. In this first approach, the isolation and preconcentration of atrazine and simazine have been selected as proof of concept. Using an internal standard made unnecessary the adjustment of the ionic strength before the extraction, thus simplifying the analytical procedure. Under the optimum conditions and using direct infusion mass spectrometry as the instrumental technique, detection limits as low as 15 ng/L were obtained. The precision calculated at three different levels was better than 8.3%. The accuracy, calculated with spiked samples, indicates the applicability of the approach for environmental water analysis.

Infrared spectroscopic monitoring of solid-state processes

We put a spotlight on IR spectroscopic investigations in materials science by providing a critical insight into the state of the art, covering both fundamental aspects, examples of its utilisation, and current challenges and perspectives focusing on the solid state.

Simulation and Validation of Porosity and Permeability of Synthetic and Real Rock Models Using Three-Dimensional Printing and Digital Rock Physics

A standard digital rock physics workflow aims to simulate petrophysical properties of rock samples using few millimeter size subsets scanned with X-ray microtomography at a high resolution of around 1 μm. The workflow is mainly based on image analysis and simulation procedures at a subset scale leading to potential uncertainties and errors that cannot be quantified experimentally. To overcome the gap between scales, we propose to integrate three-dimensional (3D) printing technology to generate enlarged subsets at a scale where experimental measurements are feasible to validate simulated results. In this study, we 3D printed synthetic and real samples and compared digital and experimental rock properties. The most challenging phase in the workflow consists of the difficulties encountered while cleaning the 3D printed samples to remove the support material. Results for subsets extracted from synthetic, sandstone, and carbonate samples showed good agreement between digital and experimental measurements for porosity values less than 12% and a range of permeability values between 100 and 2000 mD.

3D printed enzymatic microchip for multiplexed electrochemical biosensing

The low-cost e-fabrication of specialized multianalyte biosensors within the point-of-care (POC) settings in a few minutes remains a great challenge. Unlike prefabricated biosensors, 3D printing seems to be able to meet this challenge, empowering the end user with the freedom to create on-demand devices adapted to immediate bioanalytical need. Here, we describe a novel miniature all-3D-printed 4-electrode biochip, capable of the simultaneous determination of different biomarkers in a single assay. The chip is utterly fabricated via an one-step 3D printing process and it is connected to a mini portable bi-potentiostant, permitting simultaneous measurements. The bioanalytical capability of the microchip is demonstrated through the simultaneous amperometric determination of two cardiac biomarkers (cholesterol and choline) in the same blood droplet, via enzymatic assays developed on its two tiny integrated electrodes. The simultaneous determination of cholesterol and choline is free from cross-talk phenomena and interferences offering limits of detection much lower than the cut-off levels of these biomarkers in blood for coronary syndromes. The biodevice is an easy-constructed, low-cost, sensitive and e-transferable POC chip with wide scope of applicability to other enzymatic bioassays.

Additively manufactured carbon/black-integrated polylactic acid 3Dprintedsensor for simultaneous quantification of uric acid and zinc in sweat

For the first time the development of an electrochemical method for simultaneous quantification of Zn²⁺ and uric acid (UA) in sweat is described using an electrochemically treated 3D-printed working electrode. Sweat analysis can provide important information about metabolites that are valuable indicators of biological processes. Improved performance of the 3D-printed electrode was achieved after electrochemical treatment of its surface in an alkaline medium. This treatment promotes the PLA removal (insulating layer) and exposes carbon black (CB) conductive sites. The pH and the square-wave anodic stripping voltammetry technique were carefully adjusted to optimize the method. The peaks for Zn²⁺ and UA were well-defined at around - 1.1 V and + 0.45 V (vs. CB/PLA pseudo-reference), respectively, using the treated surface under optimized conditions. The calibration curve showed a linear range of 1 to 70 µg L^-1 and 1 to 70 µmol L^-1 for Zn²⁺ and UA, respectively. Relative standard deviation values were estimated as 4.8% (n = 10, 30 µg L^-1) and 6.1% (n = 10, 30 µmol L^-1) for Zn²⁺ and UA, respectively. The detection limits for Zn²⁺ and UA were 0.10 µg L^-1 and 0.28 µmol L^-1, respectively. Both species were determined simultaneously in real sweat samples, and the achieved recovery percentages were between 95 and 106% for Zn²⁺ and 82 and 108% for UA.

Fully Integrated 3D-Printed Electronic Device for the On-Field Determination of Antipsychotic Drug Quetiapine

In this work, we developed a novel all-3D-printed device for the simple determination of quetiapine fumarate (QF) via voltammetric mode. The device was printed through a one-step process by a dual-extruder 3D printer and it features three thermoplastic electrodes (printed from a carbon black-loaded polylactic acid (PLA)) and an electrode holder printed from a non-conductive PLA filament. The integrated 3D-printed device can be printed on-field and it qualifies as a ready-to-use sensor, since it does not require any post-treatment (i.e., modification or activation) before use. The electrochemical parameters, which affect the performance of the sensor in QF determination, were optimized and, under the selected conditions, the quantification of QF was carried out in the concentration range of 5 × 10⁻⁷–80 × 10⁻⁷ mol × L⁻¹. The limit of detection was 2 × 10⁻⁹ mol × L⁻¹, which is lower than that of existing electrochemical QF sensors. The within-device and between-device reproducibility was 4.3% and 6.2% (at 50 × 10⁻⁷ mol × L⁻¹ QF level), respectively, demonstrating the satisfactory operational and fabrication reproducibility of the device. Finally, the device was successfully applied for the determination of QF in pharmaceutical tablets and in human urine, justifying its suitability for routine and on-site analysis.

A 3D Printer Guide for the Development and Application of Electrochemical Cells and Devices

3D printing is a type of additive manufacturing (AM), a technology that is on the rise and works by building parts in three dimensions by the deposit of raw material layer upon layer. In this review, we explore the use of 3D printers to prototype electrochemical cells and devices for various applications within chemistry. Recent publications reporting the use of Fused Deposition Modelling (fused deposition modeling®) technique will be mostly covered, besides papers about the application of other different types of 3D printing, highlighting the advances in the technology for promising applications in the near future. Different from the previous reviews in the area that focused on 3D printing for electrochemical applications, this review also aims to disseminate the benefits of using 3D printers for research at different levels as well as to guide researchers who want to start using this technology in their research laboratories. Moreover, we show the different designs already explored by different research groups illustrating the myriad of possibilities enabled by 3D printing.

Chromatomembrane preconcentration of phenols using a new 3D printed microflow cell followed by reversed-phase HPLC determination

Chromatomembrane process represents a universal approach to the separation of compounds in liquid-gas and liquid-liquid phases systems. However, the broad application of chromatomembrane separation methods in chemical analysis is restricted by the absence of serially produced chromatomembrane flow cells and the difficulties of their laboratory production. The present work addresses the preparation of chromatomembrane flow cell by using 3D printing. Fused deposition modeling and stereolithography were modes for the production of the flow cell using acrylonitrile-butadiene-styrene and polyacrylate-based Anycubic UV resins respectively. The separation and analytical performance of the 3D-printed flow cell were compared with a polyimide unit fabricated by a milling machine, the trial addressing the determination of phenol in the air. The method is based on chromatomembrane absorption of the analytes in 95 μL of the aqueous phase positioned in the cell. Reversed-phase HPLC with fluorimetric detection was applied for the determination of the absorbed analytes. The detection limit of phenols (phenol and m-cresol) in the air was 0.9 μg/m³ by absorption preconcentration time of 10 min. The volumetric flow rate of the analyzed air through the chromatomembrane cell using an electrodriven aspirator was 0.1 L/min.