Concentrations of perfluoroalkyl and polyfluoroalkyl substances before and after full-scale landfill leachate treatment

Investigating the partitioning behavior of per- and polyfluoroalkyl substances (PFAS) during thermal landfill leachate evaporation

Thermal landfill leachate evaporator systems can reduce the volume of leachate by up to 97%, while releasing water vapor and producing residuals (volume-reduced leachate and sludge) that are managed on-site. On-site thermal evaporators offer landfill operators leachate management autonomy without being subject to increasingly stringent wastewater treatment plant requirements. However, little is known about the partitioning of PFAS within these systems, nor the extent to which PFAS may be emitted into the environment via vapor. In this study, feed leachate, residual evaporated leachate, sludge, and condensed vapor were sampled at two active full-scale thermal landfill leachate evaporators and from a laboratory-scale leachate evaporation experiment. Samples were analyzed for 91 PFAS via ultra-high pressure liquid chromatography - tandem mass spectrometry (UHPLC-MS/MS). Similar trends were observed from Evaporator 1, Evaporator 2, and the laboratory-scale evaporator; ∑PFAS were concentrated in the residual evaporated leachate during evaporation by a factor of 5.3 to 20. All condensed vapors sampled (n = 5) contained PFAS, predominantly 5:3 fluorotelomer carboxylic acid (5:3FTCA), (full-scale vapors 729 - 4087 ng/L PFAS; lab-scale vapor 61.0 ng/L PFAS). For Evaporators 1 and 2, an estimated 9 - 24% and 10%, respectively, of the PFAS mass entering the evaporators in leachate was released with vapor during the days of sample collection. '.

Per- and polyfluoroalkyl substances (PFAS) in construction and demolition debris (CDD): discerning sources and fate during waste management

As regulatory frameworks for per- and polyfluoroalkyl substances (PFAS) evolve, the solid waste community seeks to manage PFAS risks effectively. Despite extensive research on PFAS in municipal solid waste (MSW) and wastewater sludge, there is limited information on a major global waste stream which seldom gleans regulatory oversight - construction and demolition debris (CDD). This study sampled a CDD processing facility to provide material-specific information on the PFAS profile within CDD. The bulk CDD accepted by this facility was separated into major categories, representatively sampled, then characterized for total available PFAS (∑92PFAS). As reprocessed CDD is ultimately recycled or landfilled, often unencapsulated or in unlined landfills, the PFAS leaching potential was also examined using two leaching procedures. Among the categories assessed for total PFAS, carpeting, carpet padding, and gypsum drywall showed elevated concentrations compared to other components, with most of the PFAS mass contributed by precursor species. However, materials with the highest total PFAS, such as carpeting, did not necessarily exhibit the highest leaching, and leachate was predominantly composed of terminal species rather than precursors. Extrapolating these findings with national CDD generation and management data inventories suggests that despite MSW having higher total available PFAS concentrations, the leachability of PFAS from landfilled CDD is comparable, raising legitimate concerns with CDD disposal practices, particularly in unlined CDD landfills.

Can on-site leachate treatment facilities effectively address the issue of perfluoroalkyl acids (PFAAs) in leachate?

In recent decades, the presence of perfluoroalkyl acids (PFAAs) in municipal solid waste leachate has emerged as a growing concern. Research has focused on PFAA release and occurrence characteristics in landfill and waste-to-energy leachate, highlighting their significant impact when released into wastewater treatment plants. Given the extremely high loading rate faced by current on-site leachate treatment plants (LTPs), the objective of this study is to assess whether the current "anaerobic/aerobic (A/O) + membrane bioreactor (MBR) + nanofiltration (NF) + reverse osmosis (RO)" configuration is effective in PFAAs removal. Concentrations of raw and treated leachate in 10 on-site LTPs with same treatment configuration and varying landfill ages were measured, and a comprehensive mass flow analysis of each treatment process was conducted. The results indicate that A/O treatment has limited capacity for PFAA removal, while NF and RO processes reached 77.44 % and 94.30 % removal rates of ∑PFAAs concentration, respectively. Short-chain PFAAs (> 80 % detected frequency) primarily influenced the distribution and variations of PFAAs in leachate and tend to disperse in the water phase. Correlation analysis revealed the current on-site LTPs exhibit a more efficient removal capacity for long-chain PFAAs.

Characterization of per- and polyfluoroalkyl substances (PFAS) and other constituents in MSW landfill leachate from Puerto Rico

Elevated per- and polyfluoroalkyl substance (PFAS) concentrations have been reported in municipal solid waste (MSW) landfill leachate with higher levels in wet and warmer subtropical climates. Information about landfill leachate characteristics is much more limited in tropical climates. In this study, 20 landfill leachate samples were collected from three MSW landfills on the tropical island of Puerto Rico and results were compared against landfills nationally and within Florida, USA. The samples collected in Puerto Rico underwent physical-chemical analysis, as well as a quantitative analysis of 92 PFAS. Samples described in this study include discrete leachate types, such as leachate, gas condensate, and leachate which has undergone on-site treatment (e.g., RO treatment, phytoremediation, lagoons). A total of 51 PFAS were detected above quantitation limits, including perfluorohexylphosphonic acid, a perfluoroalkyl acid (PFAA) which has not been reported previously in landfill leachate. ∑PFAS concentrations in this study (mean: 38,000 ng L-1), as well as concentrations of individual PFAS, are significantly higher than other reported MSW landfill leachate concentrations. The profiles of leachates collected from on-site treatment systems indicate possible transformation of precursor PFAS as a result of treatment processes - oxidizing conditions, for example, may facilitate aerobic transformation, increase the concentrations of PFAAs, and possibly increase the apparent ∑PFAS concentration. Extreme climate events, including rising temperatures and more frequent hurricanes, have placed additional strain on the solid waste management infrastructure on the island - adding complexity to an already challenging PFAS management issue. As concern grows over PFAS contamination in drinking water, these findings should inform solid waste and leachate management decisions in order to minimize PFAS emissions in island environments.

Evaluation of per- and polyfluoroalkyl substances (PFAS) in landfill liquids from Pennsylvania, Colorado, and Wisconsin

PER: and polyfluoroalkyl substances (PFAS) have been measured in aqueous components within landfills. To date, the majority of these studies have been conducted in Florida. This current study aimed to evaluate PFAS concentrations in aqueous components (leachate, gas condensate, stormwater, and groundwater) from four landfills located outside of Florida, in Pennsylvania, Colorado, and Wisconsin (2 landfills). The Pennsylvania landfill also provided the opportunity to assess a leachate treatment system. Sample analyses were consistent across studies including the measurements of 26 PFAS and physical-chemical parameters. For the four target landfills, average PFAS concentrations were 6,900, 22,000, 280, and 260 ng L-1 in the leachate, gas condensate, stormwater, and groundwater, respectively. These results were not significantly different than those observed for landfills in Florida except for the significantly higher PFAS concentrations in gas condensate compared to leachate. For on-site treatment at the Pennsylvania landfill, results suggest that the membrane biological bioreactor (MBBR) system performed similarly as aeration-based leachate treatment systems at Florida landfills resulting in no significant decreases in ∑26PFAS. Overall, results suggest a general consistency across US regions in PFAS concentrations within different landfill liquid types, with the few differences observed likely influenced by landfill design and local climate. Results confirm that leachate exposed to open air (e.g., in trenches or in treatment systems) have lower proportions of perfluoroalkyl acid precursors relative to leachate collected in enclosed pipe systems. Results also confirm that landfills without bottom liner systems may have relatively higher PFAS levels in adjacent groundwater and that landfills in wetter climates tend to have higher PFAS concentrations in leachate.

Evaluation of per- and polyfluoroalkyl substances (PFAS) released from two Florida landfills based on mass balance analyses

Per- and polyfluoroalkyl substances (PFAS) have been found at high levels within landfill environments. To assess PFAS distributions, this study aimed to evaluate PFAS mass flux leached from disposed solid waste and within landfill reservoirs by mass balance analyses for two full-scale operational Florida landfills. PFAS mass flux in different aqueous components within landfills were estimated based on PFAS concentrations and water flow rates. For PFAS concentration, 26 PFAS, including 18 perfluoroalkyl acids (PFAAs) and 8 PFAA-precursors, were measured in samples collected from the landfills or estimated based on previous studies. Flow rates of aqueous components (rainfall, evapotranspiration, runoff, stormwater, groundwater, leakage, gas condensate, and leachate) were evaluated through the Hydrologic Evaluation of Landfill Performance model, water balance, and Darcy's Law. Results showed that the average PFAS mass flux leached from the solid waste standardized by area was estimated as 36.8 g/ha-yr, which was approximately 1 % to 3 % of the total amount of PFAS within the solid waste. The majority of PFAS leached from the solid waste (95 % to 97 %) is captured by the leachate collection system, with other aqueous components representing much smaller fractions (stormwater system at 3 % to 5 %, and gas condensate and groundwater at < 1 %). Also, based on the results, we estimate that PFAS releases will likely occur at least over 40 years. Overall, these results can help prioritize components for waste management and PFAS treatment during the anticipated landfill release periods.

Comparison of the PFAS and physical-chemical parameter fluctuations between an ash landfill and a MSW landfill

Studies of per- and polyfluoroalkyl substances (PFAS) fluctuations at landfills have focused on municipal solid waste (MSW) leachate. Few studies exist that evaluate fluctuations (defined by the coefficient of variation, CV) in MSW incinerator ash (MSWA) landfill leachate and that evaluate PFAS fluctuations in stormwater, groundwater, and treated liquids on-site. In this study, aqueous landfill samples (leachate, treated leachate, stormwater, gas condensate, ambient groundwater, and effluent from a groundwater remediation system) were collected from a MSW and an MSWA landfill geographically located within close proximity (less than 40 km). The objective of this study was to compare the leachate compositions between these two landfill types and to evaluate temporal variations. Results indicated that the CV of total detected PFAS concentrations in leachate was higher for the MSW landfill (CV = 43 %) compared to the MSWA landfill (CV = 16 %). The total detected PFAS concentration in MSW leachate samples (mean: 9641 ng/L) was higher than in MSWA leachate samples (mean: 2621 ng/L) (p < 0.05). Within a landfill, PFAS concentrations were correlated (rs > 0.6, p < 0.05) with alkalinity, total organic carbon (TOC), and ammonia. Results from the on-site leachate treatment system at the MSW landfill indicated reductions in COD, TOC, and ammonia; however, the ∑26PFAS concentration increased 3 % after the treatment. Overall, results demonstrated that differences between landfill types and fluctuations in PFAS within landfills should be considered when designing landfill leachate collection and treatment systems to remove PFAS. The comparative analysis in this study can provide insights into optimizing leachate management for MSW and MSWA landfills.

Assessing construction and demolition wood-derived biochar for in-situ per- and polyfluoroalkyl substance (PFAS) removal from landfill leachate

With regulations for per-and polyfluoroalkyl substances (PFAS) impending, the abundance of these chemicals of emerging concern in municipal solid waste (MSW) landfill leachate increasingly challenges landfill operators to seek on-site leachate pre-treatment options. This two-staged study explores the potential reuse of biochar derived from construction and demolition debris (CDD) wood as an in-situ PFAS sorbent for application within MSW landfill leachate collection systems. Batch leaching tests were first used to examine the feasibility of capturing PFAS from landfill leachate using two sources of CDD-wood-derived biochar. Then, columns were used to test the in-situ sorption capabilities of the same biochars under simulated landfill conditions. All leachates were characterized for pH, chemical oxygen demand, ammonia-nitrogen, and 92 PFAS. Seventeen PFAS were detected in the batch leaching experiment, and nine PFAS were detected in column leachates. In the batch leaching scenario, Biochar 1 achieved a maximum of 29% PFAS reduction compared to controls. Columns containing Biochar 1 generated leachates with PFAS concentrations 50% to 80% higher than those in control columns for the duration of the experiment. Columns containing Biochar 2 generated leachates with PFAS concentrations 44% less than controls in week 1 and similar concentrations in weeks 2, 3, and 4. In this study, PFAS removal from landfill leachate using biochar derived from CDD wood was not significant. Further research on biochar derived from CDD wood is needed before it can be recommended as an in-situ landfill leachate pre-treatment method.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

Fluorine mass balance analysis of PFAS in communal waters at a wastewater plant from Austria

Wastewater treatment plants are a major source of per and polyfluoroalkyl substances (PFAS) in the environment; moreover, long chain PFAS are known to accumulate in sewage sludge. Although publications on PFAS in wastewater are available from around the globe, little information is available from Central Europe. In this study influent, effluent, and sludge from two wastewater treatment plants from Austria were analysed for target PFAS compounds with HPLC MS/MS and extractable organic fluorine (EOF) content with combustion ion chromatography (CIC). The sum of 31 target PFAS increased from 22 to 47 ng L-1 in influent to 140 - 213 ng L-1 in effluent and around 10 ng g-1 in sludge, while EOF were found to be consistent (2.3 - 3.5 µg F L-1) in influent/effluent and 280 ng F g-1 in sludge. Mass balance analysis showed an increase in the identified PFAS compounds in the effluent compared to the influent (from 0.9% - 1.3% to 3.6% - 6.1%), suggesting biotransformation of non-targeted PFAS precursor compounds. In conclusion, wastewater treatment plants transform some PFAS, and wastewater effluent is a source of PFAS contamination in surface water.

Management of per- and polyfluoroalkyl substances (PFAS)-laden wastewater sludge in Maine: Perspectives on a wicked problem

This article discusses the challenges and potential solutions for managing wastewater sludge that contains per- and polyfluoroalkyl substances (PFAS), using the experience in Maine as a guide toward addressing the issue nationally. Traditional wastewater treatment, designed to remove excess organic waste and nutrients, does not eliminate persistent toxic pollutants like PFAS, instead partitioning the chemicals between discharged effluent and the remaining solids in sludge. PFAS chemistry, the molecular size, the alkyl chain length, fluorine saturation, the charge of the head group, and the composition of the surrounding matrix influence PFAS partitioning between soil and water. Land application of sludge, incineration, and storage in a landfill are the traditional management options. Land application of Class B sludge on agricultural fields in Maine peaked in the 1990s, totaling over 2 × 106 cu yd over a 40-year period and has contaminated certain food crops and animal forage, posing a threat to the food supply and the environment. Additional Class A EQ (Exceptional Quality) composted sludge was also applied to Maine farmland. The State of Maine banned the land application of wastewater sludge in August 2022. Most sludge was sent to the state-owned Juniper Ridge Landfill, which accepted 94 270 tons of dewatered sludge in 2022, a 14% increase over 2019. Between 2019 and 2022, the sum of perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) concentrations in sludge sent to the landfill ranged from 1.2 to 104.9 ng/g dw. In 2022, the landfill generated 71.6 × 106 l of leachate. The concentration of sum of six PFAS in the leachate increased sixfold between 2021 and 2022, reaching 2 441 ng/l. The retention of PFAS within solid-waste landfills and the potential for long-term release of PFAS through liners into groundwater require ongoing monitoring. Thermal treatment, incineration, or pyrolysis can theoretically mineralize PFAS at high temperatures, yet the strong C-F bond and reactivity of fluorine require extreme temperatures for complete mineralization. Future alternatives may include interim options such as preconditioning PFAS with nonpolar solvents prior to immobilization in landfills, removing PFAS from leachate, and interrupting the cycle of PFAS moving from landfill, via leachate, to wastewater treatment, and then back to the landfill via sludge. Long-term solutions may involve destructive technologies such as electron beam irradiation, electrochemical advanced oxidation, or hydrothermal liquefaction. The article highlights the need for innovative and sustainable solutions for managing PFAS-contaminated wastewater sludge.

Relationships between per- and polyfluoroalkyl substances (PFAS) and physical-chemical parameters in aqueous landfill samples

Variable chemistries of liquids from landfills can potentially impact levels of per- and polyfluoroalkyl substances (PFAS). The objective of the current study was to evaluate relationships between physical-chemical properties (bulk measurements, oxygen demand components, and metals) and PFAS concentrations in different types of aqueous landfill samples. Aqueous landfill samples were collected from 39 landfill facilities in Florida, United States. These samples included leachates from landfills that receive different waste types, such as municipal solid waste incineration ash (MSWA), construction and demolition debris (C&D), and municipal solid waste (MSW). Additional aqueous landfill samples were sourced from treated landfill leachate, gas condensate, stormwater, and groundwater from within and near the landfill boundaries. Results showed significant correlations (p < 0.05) between ∑26PFAS and alkalinity (rs = 0.83), total organic carbon (TOC) (rs = 0.84), and ammonia (rs = 0.79) for all leachate types. Other physical-chemical parameters that were significantly correlated (rs > 0.60, p < 0.05) with PFAS included specific conductivity, chemical oxygen demand (COD), and to a lesser extent, total dissolved solids (TDS) and total solids (TS). For gas condensates, PFAS was significantly correlated with TOC. Stormwater and groundwater, within and near the landfill boundaries, had considerably lower levels of PFAS and had a minimal correlation between PFAS and physical-chemical parameters. Although PFAS concentrations and physical-chemical parameters and their correlations varied between different types of aqueous landfill samples, results suggest that physical-chemical properties can be useful indicators of relative PFAS concentrations within a leachate type. More research is needed to validate the mechanisms that relate physical-chemical parameters to PFAS concentrations in landfill leachates.

Per- and Polyfluoroalkyl Substances in Personal Hygiene Products: The Implications for Human Exposure and Emission to the Environment

Per- and polyfluoroalkyl substances (PFAS) have been related to reproductive toxicity in humans, but their occurrence in some specific personal hygiene products, i.e., sanitary pads, panty liners, tampons, paper diapers, menstrual cups, and bactericidal liquids, has not been extensively studied. This work investigated 31 representative PFAS in six categories of such personal hygiene products (n = 91). Perfluorinated carboxylic acids were the primary PFAS found in the samples, accounting for over 85% of the total concentrations of PFAS. Paper diapers contained the highest sum of PFAS concentrations (64.6 ng/g) followed by sanitary pads (52.3 ng/g) and menstrual cups (21.1 ng/g). The estimated exposure doses of perfluorooctanoic acid through dermal absorption from the use of menstrual cups and paper diapers for infants (adults) were 0.77 and 2.1 (1.2) ng/kg-bw/day, which contributed more than normal dust ingestion. The estimated emission of paper diapers and sanitary pads into the environment was 2.58 and 322 kg/year with an assumed leaching rate of 100%. The potential exposure of PFAS through the use of personal hygiene products observed in this work suggests a previously unreported exposure pathway of these chemicals to humans.

PFAS in municipal landfill leachate: Occurrence, transformation, and sources

To understand sources and processes affecting per- and polyfluoroalkyl substances (PFAS), 32 PFAS were measured in landfill leachate from 17 landfills across Washington State in both pre-and post-total oxidizable precursor (TOP) assay samples, using an analytical method that was the precursor to EPA Draft Method 1633. As in other studies, 5:3FTCA was the dominant PFAS in the leachate, suggesting that carpets, textiles, and food packaging were the main sources of PFAS. Total PFAS concentrations (Σ₃₂PFAS) ranged from 61 to 172,976 ng/L and 580-36,122 ng/L in pre-TOP and post-TOP samples, respectively, suggesting that little or no uncharacterized precursors remained in landfill leachate. Furthermore, due to chain-shortening reactions, the TOP assay often resulted in a loss of overall PFAS mass. Positive matrix factorization (PMF) analysis of the combined pre- and post-TOP samples produced five factors that represent sources and processes. Factor 1 consisted primarily of 5:3FTCA (intermediate of 6:2 fluorotelomer degradation and characteristic of landfill leachate), while factor 2 was dominated by PFBS (degradant of C-4 sulfonamide chemistry) and, to a lesser extent, by several PFCAs and 5:3FTCA. Factor 3 consisted primarily of both short-chain PFCAs (end-products of 6:2 fluorotelomer degradation) and PFHxS (derived from C-6 sulfonamide chemistry), while the main component of factor 4 was PFOS (dominant in many environmental media but minor in landfill leachate, perhaps reflecting a production shift from longer to shorter chain PFAS). Factor 5, highly loaded with PFCAs, was dominant in post-TOP samples and therefore represented the oxidation of precursors. Overall, PMF analysis suggests that the TOP assay approximates some redox processes which occur in landfills, including chain-shortening reactions which yield biodegradable products.

Per- and polyfluoroalkyl substances (PFAS) distribution in landfill gas collection systems: leachate and gas condensate partitioning

While per- and polyfluoroalkyl substances (PFAS) have been reported extensively in municipal solid waste (MSW) landfill leachate,they have rarely been quantified in landfill gas or in discrete landfill liquids such as landfill gas condensate (LGC), and the potential for PFAS to partition to the condensate has not been reported. LGC and leachate collected from within gas wells known as gas well pump-out (GWP) from three MSW landfills underwent physical-chemical characterization and PFAS analysis to improve understanding of the conditions under which these liquids form and to illuminate PFAS behavior within landfills. LGC was observed to be clear liquid containing ammonia and alkalinity while GWP strongly resembled leachate - dark in color, high in chloride and ammonia. Notably, arsenic and antimony were found in concentrations exceeding regulatory thresholds by over two orders of magnitude in many LGC samples. LGC contained a lower average concentration of ΣPFAS (19,000 ng L) compared to GWP (56,000 ng L); however, LGC contained more diversity of PFAS, with 53 quantified compared to 44 in GWP. LGC contained proportionally more precursor PFAS than GWP, including more semi-volatile PFAS which are rarely measured in water matrices, such as fluorotelomer alcohols and perfluoroalkane sulfonamido ethanols. This study provides the first detailed comparison of these matrices to inform timely leachate management decisions.

Evaluation of per- and polyfluoroalkyl substances (PFAS) in leachate, gas condensate, stormwater and groundwater at landfills

Per- and polyfluoroalkyl substances (PFAS), found in many consumer products, are commonly disposed of in landfills at the end of their service lives. To identify landfill liquids that should be prioritized for treatment, this study aimed to evaluate PFAS levels in different aqueous samples from landfills and identify relationships between PFAS and landfill characteristics. Twenty-six PFAS including 11 perfluoroalkyl carboxylic acids (PFCAs), 7 perfluoroalkyl sulfonates (PFSAs), and 8 perfluoroalkyl acid precursors (PFAA-precursors) were measured in municipal solid waste (MSW) leachate, construction and demolition debris (CDD) leachate, municipal solid waste incineration (MSWI) ash leachate, gas condensate, stormwater, and groundwater from landfills. Based on the median, results show that PFAS levels in MSW leachate were the highest (10,000 ng L-1), CDD leachate were intermediate (6200 ng L-1), and MSWI ash leachate were the lowest (1300 ng L-1) among the leachates evaluated. PFAS levels in gas condensate (7000 ng L-1) were similar to MSW leachate. PFAS in stormwater and groundwater were low (medians were less than 500 ng L-1). Dominant subgroups included PFCAs and PFAA-precursors in all leachates. PFSAs were also found in CDD leachate, PFAA-precursors in gas condensate, and PFCAs in stormwater and groundwater. Landfill characteristics significantly correlated with ∑26PFAS included waste proportions (percentage of MSWI ash in landfill, |rs| = 0.22), operational status (active or not, |rs| = 0.27) and rainfall (30-d cumulative rainfall, |rs| = 0.39). The results from this study can be used to prioritize which landfills and which reservoir of liquids (and corresponding subgroup of PFAS) to target for PFAS management.

Occurrence and removal of per- and polyfluoroalkyl substances (PFAS) in leachates from incineration plants: A full-scale study

Municipal solid wastes (MSWs) contain diverse per- and polyfluoroalkyl substances (PFAS), and these substances may leach into leachates, resulting in potential threats to the environment and human health. In this study, leachates from incineration plants with on-site treatment systems were measured for 17 PFAS species, including 13 perfluorocarboxylic acids (PFCAs) and 4 perfluorosulfonic acids (PFSAs). PFAS were detected in all of the raw leachates and finished effluents in concentrations ranging from 7228 to 16,565 ng L^-1 and 43 to 184 ng L^-1, respectively, with a greater contribution from the short-chain PFAS and PFCAs. The results showed that the existing combined processes (biological treatment and membrane filtration) were effective in decreasing PFAS in the aqueous phase with removal efficiencies over 95%. In addition, correlation analysis suggested that physical entrapment, not biodegradation, was the main means of PFAS reduction in the treatment system. These results filled a gap in the understanding of PFAS occurrence and removal in leachates from incineration plants during the full-scale treatment processes, and demonstrated those leachates were previously under-explored sources of PFAS.

Do PFAS changes in landfill leachate treatment systems correlate with changes in physical chemical parameters?

Per- and polyfluoroalkyl substances (PFAS) have been found at relatively elevated concentrations in landfill leachates. Some landfill facilities treat physical-chemical parameters of their leachates using on-site leachate treatment systems before discharge. The objective of this study was to evaluate whether changes in physical-chemical parameters of leachate at on-site treatment systems (including bulk measurements, oxygen demanding components, and metals) were associated with concentration changes in PFAS. Leachates were evaluated at 15 on-site treatment facilities which included pond systems, aeration tanks, powdered activated carbon (PAC), sand filtration, reverse osmosis (RO) and combination treatment processes. Results show that most physical-chemical parameters and PFAS were significantly reduced in RO systems (over 90 %). For pond systems, statistically significant correlations (r_s > 0.6, p < 0.05) were observed between ∑₂₆PFAS changes and the changes in pH, alkalinity, ammonia, and some metals. Significant correlations were also found between ∑₈PFAAs precursors changes and specific conductivity (SPC), pH, alkalinity, ammonia, and metals changes. For aeration tank systems, significant correlations (r_s > 0.6, p < 0.05) were observed between ∑₂₆PFAS changes and changes in total dissolved solids and zinc, and between the changes of ∑₈PFAAs precursors and field pH. These correlations are believed to be associated with rainfall dilution and precipitation of calcium carbonate and other metals as leachate is introduced to the atmosphere.