Efficient treatment of perfluorohexanoic acid by nanofiltration followed by electrochemical degradation of the NF concentrate

Perfluorooctanoic acid-contaminated wastewater treatment by forward osmosis: Performance analysis

Perfluorooctanoic acid (PFOA) is a persistent compound, raising considerable global apprehension due to its resistance to breakdown and detrimental impacts on human health and aquatic environments. Pressure-driven membrane technologies treating PFAS-contaminated water are expensive and prone to fouling. This study presented a parametric investigation of the effectiveness of cellulose triacetate membrane in the forward osmosis (FO) membrane for removing PFOA from an aqueous solution. The study examined the influence of membrane orientation modes, feed pH, draw solution composition and concentration, and PFOA concentration on the performance of FO. The experimental results demonstrated that PFOA rejection was 99 % with MgCl2 and slightly >98 % with NaCl draw solutions due to the mechanism of PFOA binding to the membrane surface through Mg2+ ions. This finding highlights the crucial role of the draw solution's composition in PFOA treatment. Laboratory results revealed that membrane rejection of PFOA was 99 % at neutral and acidic pH levels but decreased to 95 % in an alkaline solution at pH 9. The decrease in membrane rejection is attributed to the dissociation of the membrane's functional groups, consequently causing pore swelling. The results were confirmed by calculating the average pore radius of the CTA membrane, which increased from 27.94 nm at pH 5 to 30.70 nm at pH 9. Also, variations in the PFOA concentration from 5 to 100 mg/L did not significantly impact the membrane rejection, indicating the process's capability to handle a wide range of PFOA concentrations. When seawater was the draw solution, the FO membrane rejected 99 % of PFOA concentrations ranging from 5 mg/L to 100 mg/L. The CTA FO treating PFOA-contaminated wastewater from soil remediation achieved a 90 % recovery rate and water flux recovery of 96.5 % after cleaning with DI water at 40 °C, followed by osmotic backwash. The results suggest the potential of using abundant and cost-effective natural solutions in the FO process, all without evident membrane fouling.

A review of electrooxidation systems treatment of poly-fluoroalkyl substances (PFAS): electrooxidation degradation mechanisms and electrode materials

The prevalence of polyfluoroalkyls and perfluoroalkyls (PFAS) represents a significant challenge, and various treatment techniques have been employed with considerable success to eliminate PFAS from water, with the ultimate goal of ensuring safe disposal of wastewater. This paper first describes the most promising electrochemical oxidation (EO) technology and then analyses its basic principles. In addition, this paper reviews and discusses the current state of research and development in the field of electrode materials and electrochemical reactors. Furthermore, the influence of electrode materials and electrolyte types on the deterioration process is also investigated. The importance of electrode materials in ethylene oxide has been widely recognised, and therefore, the focus of current research is mainly on the development of innovative electrode materials, the design of superior electrode structures, and the improvement of efficient electrode preparation methods. In order to improve the degradation efficiency of PFOS in electrochemical systems, it is essential to study the oxidation mechanism of PFOS in the presence of ethylene oxide. Furthermore, the factors influencing the efficacy of PFAS treatment, including current density, energy consumption, initial concentration, and other parameters, are clearly delineated. In conclusion, this study offers a comprehensive overview of the potential for integrating EO technology with other water treatment technologies. The continuous development of electrode materials and the integration of other water treatment processes present a promising future for the widespread application of ethylene oxide technology.

Structural dependence of PFAS oxidation in a boron doped diamond-electrochemical system

Driven by long-term persistence and adverse health impacts of legacy perfluorooctanoic acid (PFOA), production has shifted towards shorter chain analogs (C4, perfluorobutanoic acid (PFBA)) or fluorinated alternatives such as hexafluoropropylene oxide dimer acid (HFPO-DA, known as GenX) and 6:2 fluorotelomer carboxylic acid (6:2 FTCA). Yet, a thorough understanding of treatment processes for these alternatives is limited. Herein, we conducted a comprehensive study using an electrochemical approach with a boron doped diamond anode in Na2SO4 electrolyte for the remediation of PFOA common alternatives, i.e., PFBA, GenX, and 6:2 FTCA. The degradability, fluorine recovery, transformation pathway, and contributions from electro-synthesized radicals were investigated. The results indicated the significance of chain length and structure, with shorter chains being harder to break down (PFBA (65.6 ± 5.0%) < GenX (84.9 ± 3.3%) < PFOA (97.9 ± 0.1%) < 6:2 FTCA (99.4 ± 0.0%) within 120 min of electrolysis). The same by-products were observed during the oxidation of both low and high concentrations of parent PFAS (2 and 20 mg L-1), indicating that the fundamental mechanism of PFAS degradation remained consistent. Nevertheless, the ratio of these by-products to the parent PFAS concentration varied which primarily arises from the more rapid PFAS decomposition at lower dosages. For all experiments, the main mechanism of PFAS oxidation was initiated by direct electron transfer at the anode surface. Sulfate radical (SO4•-) also contributed to the oxidation of all PFAS, while hydroxyl radical (•OH) only played a role in the decomposition of 6:2 FTCA. Total fluorine recovery of PFBA, GenX, and 6:2 FTCA were 96.5%, 94.0%, and 76.4% within 240 min. The more complex transformation pathway of 6:2 FTCA could explain its lower fluorine recovery. Detailed decomposition pathways for each PFAS were also proposed through identifying the generated intermediates and fluorine recovery. The proposed pathways were also assessed using 19F Nuclear Magnetic Resonance (NMR) spectroscopy.

Cutting-edge technologies and relevant reaction mechanism difference in treatment of long- and short-chain per- and polyfluoroalkyl substances: A review

Per- and polyfluoroalkyl substances (PFAS) are emerging contaminants. Compared with short-chain PFAS, long-chain PFAS are more hazardous. Currently, little attention has been paid to the differences in reaction mechanisms between long-chain and short-chain PFAS. This pressing concern has prompted studies about eliminating PFAS and revealing the mechanism difference. The reaction rate and reaction mechanism of each technology was focused on, including (1) adsorption, (2) ion exchange (IX), (3) membrane filtration, (4) advanced oxidation, (5) biotransformation, (6) novel functional material, and (7) other technologies (e.g. ecological remediation, hydrothermal treatment (HT), mechanochemical (MC) technology, micro/nanobubbles enhanced technology, and integrated technologies). The greatest reaction rate k of photocatalysis for long- and short-chain PFAS high up to 63.0 h-1 and 19.7 h-1, respectively. However, adsorption, membrane filtration, and novel functional material remediation were found less suitable or need higher operation demand for treating short-chain PFAS. Ecological remediation is more suitable for treating natural waterbody for its environmentally friendly and fair reaction rate. The other technologies all showed good application potential for both short- and long-chain PFAS, and it was more excellent for long-chain PFAS. The long-chain PFAS can be cleavaged into short-chain PFAS by C-chain broken, -CF2 elimination, nucleophilic substitution of F-, and HF elimination. Furthermore, the application of each type of technology was novelly designed; and suggestions for the future development of PFAS remediation technologies were proposed.

Unveiling nano-empowered catalytic mechanisms for PFAS sensing, removal and destruction in water

Per- and polyfluoroalkyl substances (PFAS) are organofluorine compounds used to manufacture various industrial and consumer goods. Due to their excellent physical and thermal stability ascribed to the strong CF bond, these are ubiquitously present globally and difficult to remediate. Extensive toxicological and epidemiological studies have confirmed these substances to cause adverse health effects. With the increasing literature on the environmental impact of PFAS, the regulations and research have also expanded. Researchers worldwide are working on the detection and remediation of PFAS. Many methods have been developed for their sensing, removal, and destruction. Amongst these methods, nanotechnology has emerged as a sustainable and affordable solution due to its tunable surface properties, high sorption capacities, and excellent reactivities. This review comprehensively discusses the recently developed nanoengineered materials used for detecting, sequestering, and destroying PFAS from aqueous matrices. Innovative designs of nanocomposites and their efficiency for the sensing, removal, and degradation of these persistent pollutants are reviewed, and key insights are analyzed. The mechanistic details and evidence available to support the cleavage of the CF bond during the treatment of PFAS in water are critically examined. Moreover, it highlights the challenges during PFAS quantification and analysis, including the analysis of intermediates in transitioning nanotechnologies from the laboratory to the field.

Electrochemical oxidation of tetrahydrofurfuryl acohol on boron-doped diamond anode: Influence of current density and electrolyte solution

Tetrahydrofurfuryl alcohol (THFA), a widely applied raw materials, intermediate and solvent in the fields of agricultural, industry (especially in nuclear industry), is a potentially hazardous and non-biodegradable pollutant in wastewater. In this study, the electrochemical degradation pathways of THFA by a boron-doped diamond (BDD) anode with different current density (jappl = 20, 40 and 60 mA cm-2) and electrolyte solution (KNO3, KCl and K2SO4) was carefully investigated. The results exhibit that high chemical oxygen demand (COD) removal and mineralization rates were achieved by rapid non-selective oxidation in electrolyte solutions mediated by hydroxyl radicals (∙OH) and active chlorine (sulfate) under constant current electrolysis. In-depth data analysis using the high performance liquid chromatography and liquid chromatography/mass spectroscopy, the underlying removal pathways of THFA in KNO3, KCl and K2SO4 electrolyte solutions are proposed according to the effect of different mineralization mechanisms.

Sustainable application of electrocatalytic and photo-electrocatalytic oxidation systems for water and wastewater treatment: a review

Wastewater treatment and reuse have risen as a solution to the water crisis plaguing the world. Global warming-induced climate change, population explosion and fast depletion of groundwater resources are going to exacerbate the present global water problems for the forthcoming future. In this scenario, advanced electrochemical oxidation process (EAOP) utilising electrocatalytic (EC) and photoelectrocatalytic (PEC) technologies have caught hold of the interest of the scientific community. The interest stems from the global water management plans to scale down centralised water and wastewater treatment systems to decentralised and semicentralised treatment systems for better usage efficiency and less resource wastage. In an age of rising water pollution caused by contaminants of emerging concern (CECs), EC and PEC systems were found to be capable of optimal mineralisation of these pollutants rendering them environmentally benign. The present review treads into the conventional electrochemical treatment systems to identify their drawbacks and analyses the scope of the EC and PEC to mitigate them. Probable electrode materials, potential catalysts and optimal operational conditions for such applications were also examined. The review also discusses the possible retrospective application of EC and PEC as point-of-use and point-of-entry treatment systems during the transition from conventional centralised systems to decentralised and semi-centralised water and wastewater treatment systems.

Electrochemical-based processes for produced water and oily wastewater treatment: A review

The greatest volume of by-products produced in oil and gas recovery operations is referred to as produced water and increasing environmental concerns and strict legislations on discharging it into the environment cause to more attention for focusing on degradation methods for treatment of produced water especially electrochemical technologies. This article provides an overview of electrochemical technologies for treating oily wastewater and produced water, including: electro-coagulation, electro-Fenton, electrochemical oxidation and electrochemical membrane reactor as a single stage and combination of these technologies as multi-stage treatment process. Many researchers have carried out experiments to examine the impact of various factors such as material (i.e, electrode material) and operational conditions (i.e., potential, current density, pH, electrode distance, and other factors) for organic elimination to obtain the high efficiency. Results of each method are reviewed and discussed according to these studies, comprehensively. Furthermore, several challenges need to be overcome and perspectives for future study are proposed for each method.

Electrochemical Oxidation for Treatment of PFAS in Contaminated Water and Fractionated Foam-A Pilot-Scale Study

Per- and polyfluoroalkyl substances (PFAS) are persistent synthetic contaminants that are present globally in water and are exceptionally difficult to remove during conventional water treatment processes. Here, we demonstrate a practical treatment train that combines foam fractionation to concentrate PFAS from groundwater and landfill leachate, followed by an electrochemical oxidation (EO) step to degrade the PFAS. The study combined an up-scaled experimental approach with thorough characterization strategies, including target analysis, PFAS sum parameters, and toxicity testing. Additionally, the EO kinetics were successfully reproduced by a newly developed coupled numerical model. The mean total PFAS degradation over the designed treatment train reached 50%, with long- and short-chain PFAS degrading up to 86 and 31%, respectively. The treatment resulted in a decrease in the toxic potency of the water, as assessed by transthyretin binding and bacterial bioluminescence bioassays. Moreover, the extractable organofluorine concentration of the water decreased by up to 44%. Together, these findings provide an improved understanding of a promising and practical approach for on-site remediation of PFAS-contaminated water.

Is sorption technology fit for the removal of persistent and mobile organic contaminants from water?

Persistent, Mobile, and Toxic (PMT) and very persistent and very mobile (vPvM) substances are a growing threat to water security and safety. Many of these substances are distinctively different from other more traditional contaminants in terms of their charge, polarity, and aromaticity. This results in distinctively different sorption affinities towards traditional sorbents such as activated carbon. Additionally, an increasing awareness on the environmental impact and carbon footprint of sorption technologies puts some of the more energy-intensive practices in water treatment into question. Commonly used approaches may thus need to be readjusted to become fit for purpose to remove some of the more challenging PMT and vPvM substances, including for example short chained per- and polyfluoroalkyl substances (PFAS). We here critically review the interactions that drive sorption of organic compounds to activated carbon and related sorbent materials and identify opportunities and limitations of tailoring activated carbon for PMT and vPvM removal. Other less traditional sorbent materials, including ion exchange resins, modified cyclodextrins, zeolites and metal-organic frameworks are then discussed for potential alternative or complementary use in water treatment scenarios. Sorbent regeneration approaches are evaluated in terms of their potential, considering reusability, potential for on-site regeneration, and potential for local production. In this context, we also discuss the benefits of coupling sorption to destructive technologies or to other separation technologies. Finally, we sketch out possible future trends in the evolution of sorption technologies for PMT and vPvM removal from water.

Effective PFAS degradation by electrochemical oxidation methods-recent progress and requirement

The presence of per- and poly-fluoroalkyl substances (PFASs) in water is of global concern due to their high stability and toxicity even at very low concentrations. There are several technologies for the remediation of PFASs, but most of them are inadequate either due to limited effectiveness, high cost, or production of a large amount of sludge. Electrochemical oxidation (EO) technology shows great potential for large-scale application in the degradation of PFASs due to its simple procedure, low loading of chemicals, and least amount of waste. Here, we have reviewed the recent progress in EO methods for PFAS degradation, focusing on the last 10 years, to explore an efficient, cost-effective, and environmentally benign remediation technology. The effects of important parameters (e.g., anode material, current density, solution pH, electrolyte, plate distance, and electrical connector type) are summarized and evaluated. Also, the energy consumption, the consequence of different PFASs functional groups, and water matrices are discussed to provide an insight that is pivotal for developing new EO materials and technologies. The proposed degradation pathways of shorter-chain PFAS by-products during EO of PFAS are also discussed.

A review on superior advanced oxidation and photocatalytic degradation techniques for perfluorooctanoic acid (PFOA) elimination from wastewater

Perfluorooctanoic acid (PFOA) has been identified as the most toxic specie of the family of perfluorinated carboxylic acids (PFCAs). It has been widely distributed and frequently detected in environmental wastewater. The compound's unique features such as inherent stability, rigidity, and resistance to harsh chemical and thermal conditions, due to its multiple and strong C-F bonds have resulted in its resistance to conventional wastewater remediations. Photolysis and bioremediation methods have been proven to be inefficient in their elimination, hence this article presents intensive literature studies and summarized findings reported on the application of advanced oxidation processes (AOPs) and photocatalytic degradation techniques as the best alternatives for the PFOA elimination from wastewater. Techniques of persulfate, photo-Fenton, electrochemical, photoelectrochemical and photocatalytic degradation have been explored and their mechanisms for the degradation and defluorination of the PFOA have been demonstrated. The major advantage of AOPs techniques has been centralized on the generation of active radicals such as sulfate (SO₄^•-) hydroxyl (•OH). While for the photocatalytic process, photogenerated species (electron (e) and holes (h ⁺ _vb)) initiated the process. These active radicals and photogenerated species possessed potentiality to attack the PFOA molecule and caused the cleavage of the C-C and C-F bonds, resulting in its efficient degradation. Shorter-chain PFCAs have been identified as the major intermediates detected and the final stage entails its complete mineralization to carbon dioxide (CO₂) and fluoride ion (F^-). The prospects and challenges associated with the outlined techniques have been highlighted for better understanding of the subject matter for the PFOA elimination from real wastewaters.

Occurrence and removal of per- and polyfluoroalkyl substances (PFAS) in leachates from incineration plants: A full-scale study

Municipal solid wastes (MSWs) contain diverse per- and polyfluoroalkyl substances (PFAS), and these substances may leach into leachates, resulting in potential threats to the environment and human health. In this study, leachates from incineration plants with on-site treatment systems were measured for 17 PFAS species, including 13 perfluorocarboxylic acids (PFCAs) and 4 perfluorosulfonic acids (PFSAs). PFAS were detected in all of the raw leachates and finished effluents in concentrations ranging from 7228 to 16,565 ng L^-1 and 43 to 184 ng L^-1, respectively, with a greater contribution from the short-chain PFAS and PFCAs. The results showed that the existing combined processes (biological treatment and membrane filtration) were effective in decreasing PFAS in the aqueous phase with removal efficiencies over 95%. In addition, correlation analysis suggested that physical entrapment, not biodegradation, was the main means of PFAS reduction in the treatment system. These results filled a gap in the understanding of PFAS occurrence and removal in leachates from incineration plants during the full-scale treatment processes, and demonstrated those leachates were previously under-explored sources of PFAS.

Advanced Polymeric Nanocomposite Membranes for Water and Wastewater Treatment: A Comprehensive Review

Nanomaterials have been extensively used in polymer nanocomposite membranes due to the inclusion of unique features that enhance water and wastewater treatment performance. Compared to the pristine membranes, the incorporation of nanomodifiers not only improves membrane performance (water permeability, salt rejection, contaminant removal, selectivity), but also the intrinsic properties (hydrophilicity, porosity, antifouling properties, antimicrobial properties, mechanical, thermal, and chemical stability) of these membranes. This review focuses on applications of different types of nanomaterials: zero-dimensional (metal/metal oxide nanoparticles), one-dimensional (carbon nanotubes), two-dimensional (graphene and associated structures), and three-dimensional (zeolites and associated frameworks) nanomaterials combined with polymers towards novel polymeric nanocomposites for water and wastewater treatment applications. This review will show that combinations of nanomaterials and polymers impart enhanced features into the pristine membrane; however, the underlying issues associated with the modification processes and environmental impact of these membranes are less obvious. This review also highlights the utility of computational methods toward understanding the structural and functional properties of the membranes. Here, we highlight the fabrication methods, advantages, challenges, environmental impact, and future scope of these advanced polymeric nanocomposite membrane based systems for water and wastewater treatment applications.

A Review of PFAS Destruction Technologies

Per- and polyfluoroalkyl substances (PFASs) are a family of highly toxic emerging contaminants that have caught the attention of both the public and private sectors due to their adverse health impacts on society. The scientific community has been laboriously working on two fronts: (1) adapting already existing and effective technologies in destroying organic contaminants for PFAS remediation and (2) developing new technologies to remediate PFAS. A common characteristic in both areas is the separation/removal of PFASs from other contaminants or media, followed by destruction. The widely adopted separation technologies can remove PFASs from being in contact with humans; however, they remain in the environment and continue to pose health risks. On the other hand, the destructive technologies discussed here can effectively destroy PFAS compounds and fully address society's urgent need to remediate this harmful family of chemical compounds. This review reports and compare widely accepted as well as emerging PFAS destruction technologies. Some of the technologies presented in this review are still under development at the lab scale, while others have already been tested in the field.

Performance of in-service granular activated carbon for perfluoroalkyl substances removal under changing water quality conditions

Granular activated carbon (GAC) adsorption is one of the best available technologies for removing perfluoroalkyl substances (PFASs) from drinking water. However, GAC processes in full-scale drinking water treatment plants frequently encounter unstable, even negative removal efficiency on PFASs due to the lack of understanding between the GAC characteristics and the PFASs polluted water quality conditions. In this study, the scenarios of raw water pre-chlorination and emergency contamination by multiple PFASs were simulated to evaluate the PFASs control performance by in-service GAC with different properties and ages. The results showed that the adsorption of a relatively longer-chain PFAS by the in-service GAC can be achieved by replacing the pre-adsorbed natural organic matter (NOM). The increased lower molecular weight NOM after pre-chlorination could compete with PFASs for adsorption sites and exacerbate the pore blockage, thus significantly weakening the PFASs removal ability of in-service GAC. When multiple PFASs entered the water by emergency contamination, the PFASs with stronger hydrophobicity could replace the PFASs with less hydrophobicity that had previously been adsorbed on GAC. GAC with a higher proportion of micropores had a lower risk of PFASs leakage facing the water quality changes.

Persulfate-enhanced continuous flow three-dimensional electrode dynamic reactor for treatment of landfill leachate

Compared with sequencing batch reactor, continuous flow dynamic reactors are more conducive to promotion and application. In this study, the ability of a three-dimensional (3D) electrode dynamic reactor to remove pollutants in the landfill leachate was investigated, in which landfill leachate entered through continuous flow. Either increased of current density or the decreased of flow rate was conducive to the removal of pollutants. The optimal process parameters for current density and flow rate were 16 mA cm^-2 and 0.75 L h^-1, respectively. When the current density was constant at 16 mA cm^-2 and the flow rate was kept at 0.75 L h^-1, 60.02% of total organic carbon (TOC), 96.50% of chroma, 64.98% of chemical oxygen demand (COD) and 99.46% of ammonia nitrogen (NH₃-N) were removed. The characteristic peaks of refractory organic pollutants were reduced by 97.95%. After the reaction, the biological oxygen demand (BOD)/COD was increased from 0.24 to 0.32. As one of the emerging trace organics in landfill leachate, 85.90% of ibuprofen (IBU) was removed. The results showed that the 3D electrode dynamic reactor constructed in this study could reduce the TOC, refractory trace organic pollutant, NH₃-N and chroma in the landfill leachate. The 3D electrode dynamic reactor constructed in this research has application potential in the field of landfill leachate treatment.

Sources, occurrence, and treatment techniques of per- and polyfluoroalkyl substances in aqueous matrices: A comprehensive review

Per- and polyfluoroalkyl substances (PFAS), a class of synthetic organic pollutants, have prompted concerns about their global prevalence and possible health effects. This review consolidates the most recent data on different aspects of PFAS, such as their occurrence, and prominent sources. The current literature analysis of PFAS occurrence suggests significant variation in their concentration ranging from 0.025 to 1.2 × 10⁸ ng/L in wastewater, 0.01 to 8.9 × 10⁵ ng/L in surface water, and <0.01 to 1.3 × 10⁴ ng/L in groundwater globally. Since conventional treatment techniques are inadequate in remediating PFAS, innovative treatment approaches based on their removal or mineralization mechanism have been comprehensively reviewed. Advanced treatment technologies have shown degradation or removal of PFAS to be around 6 and > 99.9% in different aqueous matrices. However, due to significant drawbacks in their applicability in wastewater treatment plants (WWTPs), a novel treatment train approach has emerged as an effective alternative. This approach synergistically integrates multiple remediation techniques while addressing the impediments of individual treatments. Furthermore, nanofiltration (NF270) combined with electrochemical degradation has been demonstrated to be the most efficient (>98%) treatment train approach in PFAS remediation. If implemented in WWTPs, nanofiltration followed by adsorption using activated carbon is also a viable method for PFAS removal.

Review: Hydrothermal treatment of per- and polyfluoroalkyl substances (PFAS)

PER: and polyfluoroalkyl substances (PFAS) are a concerning and unique class of environmentally persistent contaminants with biotoxic effects. Decades of PFAS discharge into water and soil resulted in PFAS bioaccumulation in plants, animals, and humans. PFAS are very stable, and their treatment has become a global environmental challenge. Significant efforts have been made to achieve efficient and complete PFAS mineralization using existing and emerging technologies. Hydrothermal treatments in subcritical and supercritical water have emerged as promising end-of-life PFAS destruction technologies, attracting the attention of scholars, industry, and key stakeholders. This paper reviews the state-of-the-art research on the behavior of PFAS, PFAS precursors, PFAS alternatives, and PFAS-containing waste in hydrothermal processes, including the destruction and defluorination efficiency, the proposed reaction mechanisms, and the environmental impact of these treatments. Scientific literature shows that >99% degradation and >60% defluorination of PFAS can be achieved through subcritical and supercritical water processing. The limitations of current research are evaluated, special considerations are given to the challenges of technology maturation and scale-up from laboratory studies to large-scale industrial application, and potential future technological developments are proposed.

Removal of emerging organic micropollutants via modified-reverse osmosis/nanofiltration membranes: A review

Hazardous micropollutants (MPs) such as pharmaceutically active compounds (PhACs), pesticides and personal care products (PCPs) have emerged as a critical concern nowadays for acquiring clean and safe water resources. In the last few decades, innumerable water treatment methods involving biodegradation, adsorption and advanced oxidation process have been utilized for the removal of MPs. Of these methods, membrane technology has proven to be a promising technique for the removal of MPs due to its sustainability, high efficiency and cost-effectiveness. Herein, the aim of this article is to provide a comprehensive review regarding the MPs rejection mechanisms of reverse osmosis (RO) and nanofiltration (NF) membranes after incorporation of nanomaterials and also surface modification atop the PA layer. Size exclusion, adsorption and electrostatic charge interaction mechanisms play important roles in governing the MP removal rate. In addition, this review also discusses the state-of-the-art research on the surface modification of thin film composite (TFC) membrane and nanomaterials-incorporated thin film nanocomposite (TFN) membrane in enhancing MPs removal performance. It is hoped that this review can provide insights in modifying the physicochemical properties of NF and RO membranes to achieve better performance in water treatment process, particularly for the removal of emerging hazardous substances.

Formation of chlorate and perchlorate during electrochemical oxidation by Magnéli phase Ti4O7 anode: inhibitory effects of coexisting constituents

Formation of chlorate (ClO₃⁻) and perchlorate (ClO₄⁻) as by-products in electrooxidation process has raised concern. In the present study, the formation of ClO₃⁻ and ClO₄⁻ in the presence of 1.0 mM Cl⁻ on boron doped diamond (BDD) and Magneli phase titanium suboxide (Ti₄O₇) anodes were evaluated. The Cl⁻ was transformed to ClO₃⁻ (temporal maximum 276.2 μM) in the first 0.5 h on BDD anodes with a constant current density of 10 mA cm², while approximately 1000 μM ClO₄⁻ was formed after 4.0 h. The formation of ClO₃⁻ on the Ti₄O₇ anode was slower, reaching a temporary maximum of approximately 350.6 μM in 4.0 h, and the formation of ClO₄⁻ was also slower on the Ti₄O₇ anode, taking 8.0 h to reach 780.0 μM. Compared with the BDD anode, the rate of ClO₃⁻ and ClO₄⁻ formation on the Ti₄O₇ anode were always slower, regardless of the supporting electrolytes used in the experiments, including Na₂SO₄, NaNO₃, Na₂B₄O₇, and Na₂HPO₄. It is interesting that the formation of ClO₄⁻ during electrooxidation was largely mitigated or even eliminated, when methanol, KI, and H₂O₂ were included in the reaction solutions. The mechanism of the inhibition on Cl⁻ transformation by electrooxidation was explored.

Recent progress and challenges on the removal of per- and poly-fluoroalkyl substances (PFAS) from contaminated soil and water

Currently, due to an increase in urbanization and industrialization around the world, a large volume of per- and poly-fluoroalkyl substances (PFAS) containing materials such as aqueous film-forming foam (AFFF), protective coatings, landfill leachates, and wastewater are produced. Most of the polluted wastewaters are left untreated and discharged into the environment, which causes high environmental risks, a threat to human beings, and hampered socioeconomic growth. Developing sustainable alternatives for removing PFAS from contaminated soil and water has attracted more attention from policymakers and scientists worldwide under various conditions. This paper reviews the recent emerging technologies for the degradation or sorption of PFAS to treat contaminated soil and water. It highlights the mechanisms involved in removing these persistent contaminants at a molecular level. Recent advances in developing nanostructured and advanced reduction remediation materials, challenges, and perspectives in the future are also discussed. Among the variety of nanomaterials, modified nano-sized iron oxides are the best sorbents materials due to their specific surface area and photogenerated holes and appear extremely promising in the remediation of PFAS from contaminated soil and water.

Electrochemical oxidation processes for PFAS removal from contaminated water and wastewater: fundamentals, gaps and opportunities towards practical implementation

Electrochemical oxidation (EO) is emerging as one of the most promising methods for the degradation of recalcitrant per- and poly-fluoroalkyl substances (PFASs) in water and wastewater, as these compounds cannot be effectively treated with conventional bio- or chemical approaches. This review examines the state of the art of EO for PFASs destruction, and comprehensively compares operating parameters and treatment performance indicators for both synthetic and real contaminated water and wastewater media. The evaluation shows the need to use environmentally-relevant media to properly quantify the effectiveness/efficiency of EO for PFASs treatment. Additionally, there is currently a lack of quantification of sorption losses, resulting in a likely over-estimation of process' efficiencies. Furthermore, the majority of experimental results to date indicate that short-chain PFASs are the most challenging and need to be prioritized as environmental regulations become more stringent. Finally, and with a perspective towards practical implementation, several operational strategies are proposed, including processes combining up-concentration followed by EO destruction.

Developing innovative treatment technologies for PFAS-containing wastes

The release of persistent per- and polyfluoroalkyl substances (PFAS) into the environment is a major concern for the United States Environmental Protection Agency (U.S. EPA). To complement its ongoing research efforts addressing PFAS contamination, the U.S. EPA's Office of Research and Development (ORD) commissioned the PFAS Innovative Treatment Team (PITT) to provide new perspectives on treatment and disposal of high priority PFAS-containing wastes. During its six-month tenure, the team was charged with identifying and developing promising solutions to destroy PFAS. The PITT examined emerging technologies for PFAS waste treatment and selected four technologies for further investigation. These technologies included mechanochemical treatment, electrochemical oxidation, gasification and pyrolysis, and supercritical water oxidation. This paper highlights these four technologies and discusses their prospects and the development needed before potentially becoming available solutions to address PFAS-contaminated waste.Implications: This paper examines four novel, non-combustion technologies or applications for the treatment of persistent per- and polyfluoroalkyl substances (PFAS) wastes. These technologies are introduced to the reader along with their current state of development and areas for further development. This information will be useful for developers, policy makers, and facility managers that are facing increasing issues with disposal of PFAS wastes.

Activated carbon versus metal-organic frameworks: A review of their PFAS adsorption performance

Perfluoroalkyl and polyfluoroalkyl substances (PFAS) are a class of fluorinated aliphatic compounds considered as emerging persistent pollutants. Owing to their adverse effects on human health and environment, efficient methods of their removal from various complex matrices need to be developed. This review focuses on recent results addressing the adsorption of PFAS on activated carbons (AC) and metal-organic frameworks (MOF). While the former are well-established adsorbents used in water treatment, the latter are relatively new and still not applied at a large scale. Nevertheless, they attract research interests owing to their developed porosity and versatile surface chemistry. While AC provide high volumes of pores and hydrophobic surfaces to strongly attract fluorinated chains, MOF supply sites for acid-base complexation and a variety of specific interactions. The modifications of AC are focused on the introduction of basicity to attract PFAS anions via electrostatic/chemical interactions, and those of MOF - on structural defects to increase the pore sizes. Based on the comparison of the performance and specifically adsorption forces provided by these two groups of materials, activated carbons were pointed out as worthy of further research efforts. This is because their surface, especially that in large pores, where dispersive forces are week and where extensive pore space might be utilized to adsorb more PFAS, can be further chemically modified and these modifications might be informed by the mechanisms of PFAS adsorption, which are specific for MOF. This review emphasizes the effects of these modifications on the adsorption mechanism and brings the critical assessment of the advantages/disadvantages of both groups as PFAS adsorbents.

A Review of Treatment Techniques for Short-Chain Perfluoroalkyl Substances

In recent years, an increasing amount of short-chain perfluoroalkyl substance (PFAS) alternatives has been used in industrial and commercial products. However, short-chain PFASs remain persistent, potentially toxic, and extremely mobile, posing potential threats to human health because of their widespread pollution and accumulation in the water cycle. This study systematically summarized the removal effect, operation conditions, treating time, and removal mechanism of various low carbon treatment techniques for short-chain PFASs, involving adsorption, advanced oxidation, and other practices. By the comparison of applicability, pros, and cons, as well as bottlenecks and development trends, the most widely used and effective method was adsorption, which could eliminate short-chain PFASs with a broad range of concentrations and meet the low-carbon policy, although the adsorbent regeneration was undesirable. In addition, advanced oxidation techniques could degrade short-chain PFASs with low energy consumption but unsatisfied mineralization rates. Therefore, combined with the actual situation, it is urgent to enhance and upgrade the water treatment techniques to improve the treatment efficiency of short-chain PFASs, for providing a scientific basis for the effective treatment of PFASs pollution in water bodies globally.

Experimental insights into anodic oxidation of hexafluoropropylene oxide dimer acid (GenX) on boron-doped diamond anodes

GenX is the trade name of the ammonium salt of hexafluoropropylene oxide dimer acid (HFPO-DA) and is used as a replacement for the banned perfluorooctanoic acid (PFOA). However, recent studies have found GenX to be more toxic than PFOA. This work deals with the electrochemical degradation of HFPO-DA using boron-doped diamond anodes. For the first time, an experimental study was conducted to investigate the influence of sulfate concentration and other operating parameters on HFPO-DA degradation. Results demonstrated that sulfate radicals were ineffective in HFPO-DA degradation due to steric hindrance by -CF₃ branch. Direct electron transfer was found as the rate-determining step. By comparing degradation of HFPO-DA with that of PFOA, it was observed that the steric hindrance by -CF₃ branch in HFPO-DA decreased the rate of electron transfer from the carboxyl head group even though its defluorination rate was faster. Conclusively, a degradation pathway is proposed in which HFPO-DA mineralizes to CO₂ and F- via formation of three intermediates.

PFAS Molecules: A Major Concern for the Human Health and the Environment

Per- and polyfluoroalkyl substances (PFAS) are a group of over 4700 heterogeneous compounds with amphipathic properties and exceptional stability to chemical and thermal degradation. The unique properties of PFAS compounds has been exploited for almost 60 years and has largely contributed to their wide applicability over a vast range of industrial, professional and non-professional uses. However, increasing evidence indicate that these compounds represent also a serious concern for both wildlife and human health as a result of their ubiquitous distribution, their extreme persistence and their bioaccumulative potential. In light of the adverse effects that have been already documented in biota and human populations or that might occur in absence of prompt interventions, the competent authorities in matter of health and environment protection, the industries as well as scientists are cooperating to identify the most appropriate regulatory measures, substitution plans and remediation technologies to mitigate PFAS impacts. In this review, starting from PFAS chemistry, uses and environmental fate, we summarize the current knowledge on PFAS occurrence in different environmental media and their effects on living organisms, with a particular emphasis on humans. Also, we describe present and provisional legislative measures in the European Union framework strategy to regulate PFAS manufacture, import and use as well as some of the most promising treatment technologies designed to remediate PFAS contamination in different environmental compartments.

Degradation of antibiotics, organic matters and ammonia during secondary wastewater treatment using boron-doped diamond electro-oxidation combined with ceramic ultrafiltration

In this study, a BDD electrolytic oxidation-ceramic membrane ultrafiltration (EO-CM) system for the removals of antibiotics, organic matters and ammonia in wastewater was evaluated. Sulfamethazine (SMZ) was degraded following a pseudo first-order kinetics. The removal rate of SMZ improved with the increase of electro-oxidation time (0-60 min) and current density (5-30 mA/cm²). During the BDD electro-oxidation process, H₂O₂ and hydroxyl radicals (•OH) were generated which were detected by N, N-diethyl-p-phenylenediamine (DPD) method and electron paramagnetic resonance spectroscopy (EPR), respectively. Chemical oxygen demand (COD) was able to be removed by EO and CM processes, in which proteins and humic acids were regarded as the main removed components measured using excitation-emission matrix (EEM) technique. Moreover, BDD electro-oxidation pretreatment could make the CM process maintain a high water flux and significantly control the membrane fouling and relieve transmembrane pollution. In addition, the removal of ammonia was enhanced with the increase of chloride ions (Cl^-) in wastewater during EO process due to the generation of active chlorine (i.e., ClO^-, HClO, or Cl₂) from the oxidation of Cl^-. Chloramine and nitrogen were produced in the oxidation of ammonia by active chlorine. Overall, the results of this study suggest that BDD EO-CM system is a promising process for removing antibiotics, organic matters and ammonia.

Membrane-based technologies for per- and poly-fluoroalkyl substances (PFASs) removal from water: Removal mechanisms, applications, challenges and perspectives

Water purification from per- and poly-fluoroalkyl substances (PFASs), as a group of persistent and mobile fluoro-organic contaminants, is receiving increasing attention worldwide due to the ubiquitous presence of these highly toxic compounds. To reduce the risk of exposure of human life to PFASs and their dispersion in the environment, various techniques, primarily based on membrane technologies, have been rapidly developed. Here we critically review and analyze the current state-of-the-art of membrane-based techniques for PFASs removal, including direct membrane filtrations, adsorption-based membranes, and hybrid membrane processes. Membranes performance, treatment efficiencies, characteristic parameters and mechanisms for PFASs removal are discussed in detail. We highlight and discuss advantages and limitations, as well as challenges and prospects of individual membrane-based PFASs treatments, pointing towards the practical and sustainable application of these technologies.

Advances and Applications of Hollow Fiber Nanofiltration Membranes: A Review

Hollow fiber nanofiltration (NF) membranes have gained increased attention in recent years, partly driven by the availability of alternatives to polyamide-based dense separation layers. Moreover, the global market for NF has been growing steadily in recent years and is expected to grow even faster. Compared to the traditional spiral-wound configuration, the hollow fiber geometry provides advantages such as low fouling tendencies and effective hydraulic cleaning possibilities. The alternatives to polyamide layers are typically chemically more stable and thus allow operation and cleaning at more extreme conditions. Therefore, these new NF membranes are of interest for use in a variety of applications. In this review, we provide an overview of the applications and emerging opportunities for these membranes. Next to municipal wastewater and drinking water processes, we have put special focus on industrial applications where hollow fiber NF membranes are employed under more strenuous conditions or used to recover specific resources or solutes.

The degradation mechanisms of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS) by different chemical methods: A critical review

Per- and polyfluoroalkyl substances (PFASs) are a class of artificial compounds comprised of a perfluoroalkyl main chain and a terminal functional group. With them being applied in a wide range of applications, PFASs have drawn increasing regulatory attention and research interests on their reductions and treatments due to their harmful effects on environment and human beings. Among numerous studies, chemical treatments (e.g., photochemical, electrochemical, and thermal technologies) have been proved to be important methods to degradation PFASs. However, the pathways and mechanisms for the degradation of PFASs through these chemical methods still have not been well documented. This article therefore provides a comprehensive review on the degradation mechanisms of two important PFASs (perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS)) with photochemical, electrochemical and thermal methods. Different decomposition mechanisms of PFOA and PFOS are reviewed and discussed. Overall, the degradation pathways of PFASs are associated closely with their head groups and chain lengths, and H/F exchange and chain shortening were found to be predominant degradation mechanisms. The clear study on the degradation mechanisms of PFOA and PFOS should be very useful for the complete degradation or mineralization of PFASs in the future.

Electro-oxidation to convert dissolved organic nitrogen and soluble non-reactive phosphorus to more readily removable and recoverable forms

Conventional wastewater treatment processes cannot effectively remove dissolved organic nitrogen (DON) and soluble non-reactive phosphorus (sNRP), which can pose regulatory compliance challenges for total nitrogen and total phosphorus discharges. Moreover, DON and sNRP are not easily recoverable for beneficial reuse as part of the waste to resource paradigm. Conversion of DON and sNRP to more readily removable dissolved inorganic nitrogen (DIN) and soluble reactive phosphorus (sRP), respectively, will help meet stringent nutrient limits and facilitate nutrient recovery. In this study, electro-oxidation (EO) was evaluated for conversion of four DON compounds to DIN and five sNRP compounds to sRP. EO was more efficient and provided higher extents of conversion of the recalcitrant nutrient fractions compared to a more traditional advanced oxidation process, UV/H₂O₂. Direct electron transfer was likely the dominant oxidation mechanism for EO-based DON and sNRP conversion, with DON being more recalcitrant. Among the DON compounds tested, greater availability of primary amine (C-N bonds) yielded greater conversion compared to compounds with fewer primary amine or those with secondary amine (C-N-C bond). Among the sNRP compounds tested, those with P-O-C bonds (organic sNRP) converted more readily than those with P-O-P bonds (inorganic sNRP), presumably because cleavage of the latter bond requires greater energy. Using 30 min of EO treatment, the highest DON and sNRP compound conversion was 11.7 ± 0.09% for urea and 31.1 ± 0.75% for beta-glycerol phosphate. A similar extent of EO-based conversion of DON (6.41 ± 1.5%) and sNRP (32.7 ± 3.3%) was observed in real wastewater.

Electrochemical advanced oxidation processes coupled with membrane filtration for degrading antibiotic residues: A review on its potential applications, advances, and challenges

Antibiotic pollution is mainly caused by aquaculture wastewater and pharmaceuticals, which are frequently used by humans. Due to limited treatment efficiency or improper selection of treatment methods, these antibiotic residues may be very harmful in human drinking water and aquatic environments. The EAOPs coupling membrane technology (EAOPs-membrane) can play their own advantages, which can significantly improve the degradation efficiency and alleviate membrane pollution (electrochemical manners). In this context, this review mainly collecting researches and information on EAOPs-membrane treatment of antibiotic pollution published between 2012 and 2020. Discussed the different combinations of these two technologies, the mechanism of them in the system to improve the processing efficiency, prolong the working time, and stabilize the system structure. Mainly due to the synergistic effect of electrochemical behavior such as electric repulsion and in-situ oxidation, the membrane fouling in the system is alleviated. In this review it was summarized that the selection of different membrane electrode materials and their modifications. The paper also elaborates the existing challenges facing the EAOPs-membrane methods for antibiotic pollution treatment, and their prospects.

An electro-oxidation reactor for treatment of nanofiltration concentrate towards zero liquid discharge

Nanofiltration (NF) concentrate generated from the secondary wastewater treatment contains high concentration of ammonium nitrogen and refractory organics, thus having great environmental risks. In this study, an electro-oxidation (EO) reactor built up with a boron-doped diamond (BDD) anode is utilized to treat the NF concentrate. To reach "zero liquid discharge", a mixture of the electrolytic effluent and the raw secondary wastewater was collected and transported back to the NF module. Results show that under the current density of 30 mA·cm^-2, most of ammonia nitrogen was decomposed into N-gases within 30 min due to the active chlorine radicals generated in the electrochemical process. Moreover, the EO reactor completely eliminated antibiotics, humic acids and bacteria in the NF concentrate under long electrolysis time of 60 min. In particular, the organic pollutants removal rate was kept at a stable value in the EO reactor for a long-term operation of up to 120 h. In addition, the NF membrane remained a constant permeate flux without being affected by the membrane biofouling caused by organic components in wastewater. Our study highlights the potential of the NF-EO process as a "zero liquid discharge" approach for treatment of the secondary wastewater.

A review of the occurrence, transformation, and removal of poly- and perfluoroalkyl substances (PFAS) in wastewater treatment plants

Poly- and perfluoroalkyl substances (PFAS) comprise more than 4,000 anthropogenically manufactured compounds with widescale consumer and industrial applications. This critical review compiles the latest information on the worldwide distribution of PFAS and evaluates their fate in wastewater treatment plants (WWTPs). A large proportion (>30%) of monitoring studies in WWTPs were conducted in China, followed by Europe (30%) and North America (16%), whereas information is generally lacking for other parts of the world, including most of the developing countries. Short and long-chain perfluoroalkyl acids (PFAAs) were widely detected in both the influents (up to 1,000 ng/L) and effluents (15 to >1,500 ng/L) of WWTPs. To date, limited data is available regarding levels of PFAS precursors and ultra-short chain PFAS in WWTPs. Most WWTPs exhibited low removal efficiencies for PFAS, and many studies reported an increase in the levels of PFAAs after wastewater treatment. The analysis of the fate of various classes of PFAS at different wastewater treatment stages (aerobic and/aerobic biodegradation, photodegradation, and chemical degradation) revealed biodegradation as the primary mechanism responsible for the transformation of PFAS precursors to PFAAs in WWTPs. Remediation studies at full scale and laboratory scale suggest advanced processes such as adsorption using ion exchange resins, electrochemical degradation, and nanofiltration are more effective in removing PFAS (~95-100%) than conventional processes. However, the applicability of such treatments for real-world WWTPs faces significant challenges due to the scaling-up requirements, mass-transfer limitations, and management of treatment by-products and wastes. Combining more than one technique for effective removal of PFAS, while addressing limitations of the individual treatments, could be beneficial. Considering environmental concentrations of PFAS, cost-effectiveness, and ease of operation, nanofiltration followed by adsorption using wood-derived biochar and/or activated carbons could be a viable option if introduced to conventional treatment systems. However, the large-scale applicability of the same needs to be further verified.

Defect Engineering on a Ti4O7 Electrode by Ce3+ Doping for the Efficient Electrooxidation of Perfluorooctanesulfonate

Defect engineering in an electrocatalyst, such as doping, has the potential to significantly enhance its catalytic activity and stability. Herein, we report the use of a defect engineering strategy to enhance the electrochemical reactivity of Ti₄O₇ through Ce³⁺ doping (1-3 at. %), resulting in the significantly accelerated interfacial charge transfer and yielding a 37-129% increase in the anodic production of the hydroxyl radical (OH^•). The Ce³⁺-doped Ti₄O₇ electrodes, [(Ti_1-xCe_x)₄O₇], also exhibited a more stable electrocatalytic activity than the pristine Ti₄O₇ electrode so as to facilitate the long-term operation. Furthermore, (Ti_1-xCe_x)₄O₇ electrodes were also shown to effectively mineralize perfluorooctanesulfonate (PFOS) in electrooxidation processes in both a trace-concentration river water sample and a simulated preconcentration waste stream sample. A 3 at. % dopant amount of Ce³⁺ resulted in a PFOS oxidation rate 2.4× greater than that of the pristine Ti₄O₇ electrode. X-ray photoelectron spectroscopy results suggest that Ce³⁺ doping created surficial oxygen vacancies that may be responsible for the enhanced electrochemical reactivity and stability of the (Ti_1-xCe_x)₄O₇ electrodes. Results of this study provide insights into the defect engineering strategy for boosting the electrochemical performance of the Ti₄O₇ electrode with a robust reactivity and stability.

Reverse osmosis and nanofiltration membranes for highly efficient PFASs removal: overview, challenges and future perspectives

PFASs are called “forever chemicals” because they do not fully degrade. They have become so ubiquitous in the environment that it is difficult to prevent exposure. This review aims to provide a set of improved technologies to remove PFASs from water.

Rejection of per- and polyfluoroalkyl substances (PFASs) in aqueous film-forming foam by high-pressure membranes

The ubiquitous use and manufacturing of per- and polyfluoroalkyl substances (PFASs) have led to the contamination of water resources worldwide. High-pressure membranes, including nanofiltration (NF) and reverse osmosis (RO), are increasingly being deployed for water treatment and may be an effective barrier to PFASs. However, the impact of membrane operating conditions, background water matrix, and solute adsorption on rejection of diverse PFASs by NF and RO remains unclear. Rejection of perfluoroalkyl acids (PFAAs) present in aqueous film-forming foam (AFFF) diluted into a laboratory electrolyte matrix by NF and RO spiral wound elements was >98% and >99%, respectively. Rejection of the same PFAAs present in an AFFF-impacted groundwater matrix by NF was lower, between 92-98%, and was attributed to background water matrix constituents. Operating conditions did not have a significant impact on rejection of PFASs with the exception of shorter chain perfluoroalkyl sulfonic acids (PFSAs) in the AFFF-impacted groundwater matrix, where rejection increased with increasing flux. Structure-activity analysis of 42 PFASs, including 10 PFAAs and 32 PFASs identified in AFFF through high-resolution mass spectrometry suspect screening methods, showed some correlation between rejection and compound molecular weight. Adsorptive losses of PFAAs, most notably longer-chain hydrophobic PFAAs, to the spiral wound membrane elements and the membrane system were observed. Adsorption of PFAAs to the permeate spacer was especially pronounced and may have implications of artificially high rejection values. Still, rejection of PFASs by NF remained consistently >98% over 13 days of continuous operation.

Photo enhanced degradation of polyfluoroalkyl and perfluoroalkyl substances

The increase in the presence of highly recalcitrant poly- and per- fluoroalkyl substances (PFAS) in the environment, plant tissues and animals continues to pose serious health concerns. Several treatment methods such as physical, biological and chemical processes have been explored to deal with these compounds. Current trends have shown that the destructive treatment processes, which offer degradation and mineralization of PFASs, are the most desirable process among researchers and policy makers. This article, therefore, reviews the degradation and defluorination processes, their efficiencies and the degradation mechanism of photon-based processes. It shows that high degradation and defluorination efficiency of PFASs could be achieved by photon driven processes such as photolysis, photochemical, photocatalysis and photoreduction. The efficiency of these processes is greatly influenced by the nature of light and the reactive radical generated in the system. The limitation of these processes, however, include the long reaction time required and the use of anoxic reaction conditions, which are not obtainable at ambient conditions.