Enhanced dewaterability of anaerobically digested sludge by in-situ free nitrous acid treatment

Advanced application of tea residue extracts rich in polyphenols for enhancing sludge dewaterability: Unraveling the role of pH regulation

Tea polyphenols (TPs), as a kind of derivatives from tea waste, were employed as a novel environmentally friendly bio-based sludge conditioner in this study. The findings showed that when TPs were applied at a dosage of 300 mg g-1 DS, the sludge CST0/CST ratio significantly increased to 1.90. pH regulation was found to markedly affect the dewatering efficiency of sludge. At pH 4, the CST0/CST rose to 2.86, coupled with a reduction in the specific resistance to filtration (SRF) from 6.69 × 1013 m kg-1 to 1.43 × 1013 m kg-1 and a decrease in the moisture content (MC) from 90.57% to 68.75%. TPs formed complexes and precipitated sludge proteins, as demonstrated by changes in the extracellular polymeric substances (EPS), viscosity, zeta potential, and particles size distribution. The optimization significance of acidification treatment on sludge structure disintegration, the interaction of TPs with EPS, and the removal of sludge proteins were elucidated. The research provided an ideal approach for the integrated utilization of biomass resources from tea waste and highlighted the potential application of TPs as an environmentally friendly conditioner in sludge dewatering.

Enhanced anaerobic digestion of waste-activated sludge by thermal-alkali pretreatment: a pilot-scale study

The composition of waste-activated sludge (WAS) is complex, containing a large amount of harmful substances, which pose a threat to the environment and human health. The reduction and resource utilization of sludge has become a development demand in sludge treatment and disposal. Based on the technical bottlenecks in the practical application of direct anaerobic digestion technology, this study adopted two different thermal and thermal-alkali hydrolysis technologies to pretreat sludge. A pilot-scale experiment was conducted to investigate the experimental conditions, parameters, and effects of two hydrolysis technologies. This study showed that the optimal hydrolysis temperature was 70 °C, the hydrolysis effect and pH can reach equilibrium with the hydrolysis retention time was 4-8 h, and the optimal alkali concentration range was 0.0125-0.015 kg NaOH/kg dry-sludge. Thermal-alkali combination treatment greatly improved the performance of methane production, the addition of NaOH increased methane yield by 31.2% than that of 70 °C thermal hydrolysis. The average energy consumption is 75 kWh/m3 80% water-content sludge during the experiment. This study provides a better pretreatment strategy for exploring efficient anaerobic digestion treatment technologies suitable for southern characteristic sewage sludge.

Peracetic acid (PAA)-based pretreatment effectively improves medium-chain fatty acids (MCFAs) production from sewage sludge

Peracetic acid (PAA), known for its environmentally friendly properties as a oxidant and bactericide, is gaining prominence in decontamination and disinfection applications. The primary product of PAA oxidation is acetate that can serve as an electron acceptor (EA) for the biosynthesis of medium-chain fatty acids (MCFAs) via chain elongation (CE) reactions. Hence, PAA-based pretreatment is supposed to be beneficial for MCFAs production from anaerobic sludge fermentation, as it could enhance organic matter availability, suppress competing microorganisms and furnish EA by providing acetate. However, such a hypothesis has rarely been proved. Here we reveal that PAA-based pretreatment leads to significant exfoliation of extracellular polymeric substances (EPS) from sludge flocs and disruption of proteinic secondary structures, through inducing highly active free radicals and singlet oxygen. The production of MCFAs increases substantially to 11,265.6 mg COD L-1, while the undesired byproducts, specifically long-chain alcohols (LCAs), decrease to 723.5 mg COD L-1. Microbial activity tests further demonstrate that PAA pretreatment stimulates the CE process, attributed to the up-regulation of functional genes involved in fatty acid biosynthesis pathway. These comprehensive findings provide insights into the effectiveness and mechanisms behind enhanced MCFAs production through PAA-based technology, advancing our understanding of sustainable resource recovery from sewage sludge.

Potential of free nitrous acid (FNA) for sludge treatment and resource recovery from waste activated sludge: A review

The escalating production of waste activated sludge (WAS) presents significant challenges to wastewater treatment plants (WWTPs). Free nitrous acid (FNA), known for its biocidal effect, has gained a growing focus on sludge dewatering, sludge reduction, and resource recovery from WAS due to its eco-friendly and cost-effective properties. Nevertheless, there have been no attempts made to systematically summarize or critically analyze the application of FNA in enhancing treatment and resource utilization of sludge. In this paper, we provided an overview of the current understanding regarding the application potential and influencing factors of FNA in sludge treatment, with a specific focus on enhancing sludge dewatering efficiency and reducing volume. To foster resource development from sludge, various techniques based on FNA have recently been proposed, which were comprehensively reviewed with the corresponding mechanisms meticulously discussed. The results showed that the chemical oxidation and interaction with microorganisms of FNA played the core role in improving resource utilization. Furthermore, current challenges and future prospects of the FNA-based applications were outlined. It is expected that this review can refine the theoretical framework of FNA-based processes, providing a theoretical foundation and technical guidance for the large-scale demonstration of FNA.

Green synthesis of Fe3O4@ceramsite from sludge improving anaerobic digestion performance of waste activated sludge

Anaerobic digestion (AD) is a promising technique for waste management, which can achieve sludge stabilization and energy recovery. This study successfully prepared Fe3O4@ceramsite from WAS and applied it as an additive in sludge digestion, aiming to improve the conversion of organics to biomethane efficiency. Results showed that after adding the Fe3O4@ceramsite, the methane production was enhanced by 34.7% compared with the control group (88.0 ± 0.1 mL/g VS). Further mechanisms investigation revealed that Fe3O4@ceramsite enhanced digesta stability by strong buffering capacity, improved sludge conductivity, and promoted Fe (III) reduction. Moreover, Fe3O4@ceramsite has a larger surface area and better porous structure, which also facilitated AD performance. Microbial community analysis showed that some functional anaerobes related to AD such as Spirochaeta and Smithella were enriched with Fe3O4@ceramsite treatment. Potential syntrophic metabolisms between syntrophic bacteria (Syntrophomonas, associated with DIET) and methanogens were also detected in the Fe3O4@ceramsite treatment AD system.

Synergic effects of free ammonia and sodium percarbonate for enhancing short-chain fatty acid production during sludge fermentation: Effectiveness assessment and mechanism elucidation

The production of short-chain fatty acids (SCFAs) from waste activated sludge (WAS) via anaerobic fermentation is typically restricted by poor sludge decomposition capacity and low substrate-availability. Therefore, the free ammonia (FA)‑sodium percarbonate (SPC) technology was presented to successfully overcome the limitation while addressing unsatisfactory acidogenic fermentation pretreated with sole FA or SPC. It revealed that FA + SPC co-pretreatment could boost the SCFA concentration to 347.1 mg COD/g VSS at 180 mg/L FA and 0.15 g/g TSS SPC. In-depth studies demonstrated that FA + SPC pretreatment greatly improved sludge disintegration, biodegradability of substrates and acidification of hydrolysis products. Furthermore, FA + SPC co-pretreatment stimulated the activity of hydrolytic and acidogenic enzymes but inhibited methanogenic enzymes while changing the microbial structure and promoting the enrichment of fermentation microorganisms. The synergistic effect of FA and SPC in this work improves the yield of SCFAs from WAS and facilitates the study of WAS carbon resource recovery.

Anaerobic co-fermentation of waste activated sludge with corn gluten meal enhanced phosphorus release and volatile fatty acids production: Critical role of corn gluten meal dosage on fermentation stages and microbial community traits

The anaerobic co-fermentation of iron bound phosphorus (P) compounds (FePs)-bearing sludge with corn gluten meal (CGM) and the underlying mechanisms associated with P release and volatile fatty acids (VFAs) production were investigated. The optimal CGM dosage for P release was 0.6 g chemical oxygen demand (COD)/g total suspended solid (TSS), which resulted in an increase in efficiency from 7 % (control sample) to 39 %. However, the optimal CGM dosage for VFAs production was 0.4 g COD/g TSS, and the yield increased from 37.4 (control sample) to 331.7 mg COD/g volatile suspended solid. The addition of CGM enhanced hydrolysis and acidogenesis by supplying abundant organic substrates to promote the growth of hydrolytic and acidogenic bacteria. A higher VFAs/ammonium-nitrogen ratio resulted in a lower pH, which promoted greater FePs dissolution and P release from the sludge. This study provides novel insights into the effects of CGM on P release and VFAs production.

Filamentous cyanobacteria and hydrophobic protein in extracellular polymeric substances facilitate algae-bacteria aggregation during partial nitrification

In algae-bacteria symbiotic wastewater treatment, the excellent settling performance of algae-bacteria aggregates is critical for biomass separation and recovery. Here, the composition of extracellular polymeric substances (EPS), microbial profiles, and functional genes of algae-bacteria aggregates were investigated at different solid retention times (SRTs) (10, 20, and 40 d) during partial nitrification in photo sequencing bioreactors (PSBRs). Results showed that SRTs greatly influenced the nitrogen transformation and the formation and morphological structure of algae-bacteria aggregates. The highest nitrite accumulation, the largest particle size (~1.54 mm) and the best settling performance were observed for the algae-bacteria aggregates in the PSBR with an SRT of 10 d, where the abundant occurrence of filamentous cyanobacteria with the highest ratio of chlorophyll a/b and the lowest EPS amount with the highest protein-to-polysaccharide ratio were observed. In particular, the EPS at 10 d of SRT contained a higher amount of protein-related hydrophobic groups and a lower ratio of α-helix/(β-sheet + random coil), indicating a looser protein structure, which might facilitate the formation and stabilization of algae-bacteria aggregates. Moreover, algal-bacterial aggregation greatly depended on the composition and evolution of filamentous cyanobacteria (unclassified _o__Oscillatoriales and Phormidium accounted for 56.29 % of the identified algae at SRT 10 d). The metagenomic analysis further revealed that functional genes related to amino acid metabolism (e.g., genes of phenylalanine, tyrosine, and tryptophan biosynthesis) were expressed at high levels within 10 d of SRT. Overall, this study demonstrates the influence of EPS structures and filamentous cyanobacteria on algae-bacteria aggregation and reveals the biological mechanisms driving photogranule structure and function.

N-acyl homoserine lactone mediating initial adhesion of microalgal biofilm formation

While pioneering methods have demonstrated that bacterial N-acyl homoserine lactone (AHL) signaling molecules can influence the growth and self-aggregation of suspended microalgae, whether AHLs can affect the initial adhesion to a carrier has remained an open question. Here we revealed that the microalgae exhibited different adhesion potential under AHL mediation, where the performance was affiliated to both AHL types and concentrations. The result can be well explained by the interaction energy theory, where the energy barrier between the carriers and the cells varied due to AHL mediation. Depth analyses revealed that AHL acted through modifying the properties of the surface electron donor of the cells, which were dependent upon three major components, i.e., extracellular protein (PN) secretion, the PN secondary structure, and the PN amino acid composition. These findings expand the known diversity of AHLs mediation on microalgal initial adhesion and metabolisms, which may interface with other major cycles and become helpful to theoretically guide the application of AHLs in microalgal culture and harvesting.

Free nitrous acid-assisted asymmetrical alternating current electrochemistry (FNA-AACE) for multi-heavy metals decontamination in waste activated sludge

Heavy metal contamination of waste activated sludge (WAS) is a key factor limiting the land application of sludge for nutrients recovery. This study proposes a novel free nitrous acid (FNA)-assisted asymmetrical alternating current electrochemistry (FNA-AACE) process to achieve high-efficiency decontamination of multi-heavy metals (Cd, Pb, and Fe) in WAS. The optimal operating conditions, the heavy metal removal performance of FNA-AACE, and the related mechanisms for maintaining the high performance were systematically investigated. During the FNA-AACE process, FNA treatment was optimal with an exposure time of 13 h at a pH of 2.9 and an FNA concentration of 0.6 mg/g TSS. Then the sludge was washed with EDTA in a recirculating leaching system under asymmetrical alternating current electrochemistry (AACE). The 6-h working and the following electrode cleaning were defined as a working circle of AACE. After three cycles of working-cleaning periods in AACE treatment, the cumulative removal efficiency of the toxic metals Cd and Pb reached over 97% and 93%, respectively, whilst that of Fe was greater than 65%. This surpasses most previously reported efficiencies and possesses a shorter treatment duration and sustainable EDTA circulation. The mechanism analysis suggested that FNA pretreatment provoked the migration of heavy metals for leaching enhancement, as well as reduced the demand for EDTA eluent concentration and increased conductivity, which can improve the AACE efficiency. Meanwhile, the AACE process absorbed the anionic chelates of heavy metals and reduced them to zero-valent particles on the electrode, regenerating the EDTA eluent and maintaining its high extraction efficiency for heavy metals. In addition, FNA-AACE could provide different electric field operation modes, allowing it to have flexibility for the real application processes. This proposed process is expected to be coupled with anaerobic digestion in wastewater treatment plants (WWTPs) for high efficiency of heavy metal decontamination, sludge reduction, and resource/energy recovery.

Effect and mechanism of perfluorooctanoic acid (PFOA) on anaerobic digestion sludge dewaterability

Perfluorooctanoic acid (PFOA) as nonbiodegradable organic pollutant, its presence and risks in wastewater treatment system has aroused wide concern. This study investigated the effect and underlying mechanism of PFOA on anaerobic digestion sludge (ADS) dewaterability. Long-term exposure experiments were set up to investigate the effect with various concentration of PFOA dosed. Experimental results suggested that the existence of high concentration PFOA (over 1000 μg/L) could deteriorate ADS dewaterability. The long-term exposure to 100,000 μg/L PFOA of ADS increased specific resistance filtration (SRF) by 81.57%. It was found that PFOA promoted the release of extracellular polymeric substances (EPS), which was strongly associated with sludge dewaterability. The fluorescence analysis revealed that the high PFOA concentration could significantly improve the percentage of protein-like substances and soluble microbial by-product-like content, and then further deteriorated the dewaterability. The FTIR results showed that long-term exposure of PFOA caused loose protein structure in sludge EPS, which led to loose sludge floc structure. The loose sludge floc structure aggravated the deterioration of sludge dewaterability. The solids-water distribution coefficient (K_d) decreased with the increase of initial PFOA concentration. Moreover, PFOA significantly affected microbial community structure. Metabolic function prediction results showed significant decrease of fermentation function exposed to PFOA. This study revealed that the PFOA with high concentration could deteriorated sludge dewaterability, which should be highly concerned.

Fe(III) enhances Cr(VI) bioreduction in a MFC-granular sludge coupling system: Experimental evidence and metagenomics analysis

The influence of Fe(III) on the bioreduction efficiency of Cr(VI) in a microbial fuel cell (MFC)-granular sludge coupling system using dissolved methane as an electron donor and carbon source was explored, and the mechanism of Fe(III) mediating enhancement in the bioreduction process of Cr(VI) in the coupling system was also investigated. Results showed that the presence of Fe(III) enhanced the ability of the coupling system to reduce Cr(VI). The average removal efficiencies of Cr(VI) in the anaerobic zone in response to 0, 5, and 20 mg/L of Fe(III) were 16.53±2.12%, 24.17±2.10%, and 46.33±4.41%, respectively. Fe(III) improved the reducing ability and output power of the system. In addition, Fe(III) enhanced the electron transport systems activity of the sludge, the polysaccharide and protein content in the anaerobic sludge. Meanwhile, X-ray photoelectron spectrometer (XPS) spectra demonstrated that Cr(VI) was reduced to Cr(III), while Fe2p participated in reducing Cr(VI) in the form of Fe(III) and Fe(II). Proteobacteria, Chloroflexi, and Bacteroidetes were the dominant phylum in the Fe(III)-enhanced MFC-granular sludge coupling system, accounting for 49.7%-81.83% of the microbial community. The relative abundance of Syntrophobacter and Geobacter increased after adding Fe(III), indicating that Fe(III) contributed to the microbial mediated anaerobic oxidation of methane (AOM) and bioreduction of Cr(VI). The genes mcr, hdr, and mtr were highly expressed in the coupling system after the Fe(III) concentration increased. Meanwhile, the relative abundances of coo and aacs genes were up-regulated by 0.014% and 0.075%, respectively. Overall, these findings deepen understanding of the mechanism of the Cr(VI) bioreduction in the MFC-granular sludge coupling system driven by methane under the influence of Fe(III).

New strategy of drinking water sludge as conditioner to enhance waste activated sludge dewaterability: Collaborative disposal

Drinking water sludge (DWS) and waste activated sludge (WAS) are usually treated separately. With the continuous deepening understanding of the characteristics of two types sludge, the research and application of the collaborative disposal is worth considering. The heated modification DWS (HDWS) rich in inorganic matter and aluminum (Al₂O₃) can be used as a conditioner to enhance WAS dewaterability using its properties with physical skeleton and chemically catalyzed ozone (O₃). The results showed that the minimum values of capillary water time (CST) and specific resistance filtration (SRF) for WAS were 20.9±2.40 s and 1.07±0.19×10¹³ m/kg at pH=4, O₃ dosage=60 mg/g VS and HDWS dosage=700 mg/g VS, corresponding to the reduction of sludge cake water content (Wc) to 60.37±0.97 %. The mechanism of HDWS+O₃ enhanced WAS dewaterability was systematically elucidated through pyridine-infrared analysis and density functional theory (DFT) calculations. The surface of Al₂O₃ in HDWS had more Lewis acidic sites, and the oxygen atoms of O₃ combined with Al atoms to form Al-O bonds and undergo electron transfer, while O₃ molecules dissociated to produce more hydroxyl radicals (·OH). With the oxidation of ·OH, the extra-microcolony/cellular polymers (EMPS/ECPS) structure were destroyed and became looser, promoting the conversion of internal moisture to free moisture. Zeta potential tended to zero, particle size increased, and the surface was more hydrophobic. Correlation analysis revealed that the component content, protein (PN) secondary structure and molecular weight (MW) in ECPS were positively and more strongly correlated with the sludge dewaterability compared to EMPS. The discovery of HDWS+O₃ applied to effectively enhance WAS dewaterability provided an inspiring perspective on the emerging DWS and WAS co-processing disposition.

A novel insight on the intensification mechanism of sludge dewaterability by ionic liquids

The huge output of sewage sludge has caused a remarkable environmental burden. Sludge dewatering is considered as an important way to reduce the sludge volume. Five imidazole-based ionic liquids were used to improve the dewaterability of sewage sludge. 1-ethyl-3-methylimidazolium dihydrogen phosphate ([Emim][H₂PO₄]) was screened out as a potential conditioner of sludge due to its excellent dewatering performance and reusability. The solid content of sludge filter cake after treatment with [Emim][H₂PO₄] was about 10% higher than that of sludge treated by cationic polyacrylamides (CPAM). The intensification mechanism of ionic liquids to the improvement of sludge dewatering performance was studied. The presence of acidic ionic liquids [Emim][H₂PO₄] resulted the increase of zeta potential from -14.57 ± 0.81 mV to -5.60 ± 0.30 mV and led to the protonation of biopolymers. Acidic ionic liquids [Emim][H₂PO₄] inactivated the microorganism and led to a porous and unconsolidated structure of the solid sludge particles. All these effects were conducive to destroy the microstructure of sludge and release water. However, [Emim]Cl, [Bmim][OTf] and [Hmim][OTf] showed little effect on the protonation of ionizable functional groups at near-neutral environment. The dissolution of biopolymer decreased the zeta potential and strengthened the electrostatic repulsion. So, they showed weaker intensification effects than CPAM.

Enhanced sludge dewaterability by ferrate/ferric chloride: The key role of Fe(IV) on the changes of EPS properties

The complex characteristics of extracellular polymeric substances (EPS) seriously affect the improvement of sludge dewaterability. Ferrate (Fe(VI))/ferric chloride (Fe(III)) was applied through its strong oxidability to effectively enhance sludge dewaterablity by changing the properties of EPS in this study. Results confirmed that water content (WC), specific resistance to filtration (SRF) and capillary suction time (CST) fell from 82.8 %, 9.3 × 10¹⁰ s²/g and 35.1 s to 76.1 %, 2.6 × 10¹⁰ s²/g and 16.2 s, respectively, when adding 12 mg Fe(VI)/g VSS and 12 mg Fe(III)/g VSS with the dosing interval of 5 min. Investigations of the mechanism strongly suggested that Fe(VI) was successfully catalyzed by Fe(III), promoting the generation of methyl phenyl sulfone (PMSO₂) and facilitating the electron transfer, with Fe(IV) having the major role in the oxidation process. Furthermore, sludge water-holding capacity and hydrophilicity waned after oxidation due to the destruction of EPS structure, which promoted the decrement of bound water to enhance the discharge of sludge water, so as to improve the efficiency of dewatering.

Improving sludge dewaterability by free nitrous acid and lysozyme pretreatment: Performances and mechanisms

Reducing the water content of waste activated sludge (WAS) is critical for sludge treatment and disposal in wastewater treatment plants (WWTPs). In this study, a new combined conditioning processes by using lysozyme (LZM) and free nitrous acid (FNA) were proposed and demonstrated to enhance the dewaterability of WAS. The water content of sludge cake dropped from 82.82 % to 68.42 % (1 h FNA treatment + 1 h LZM treatment) and 69.52 % (6 h FNA treatment + 1 h LZM treatment) with the combined FNA and LZM treatment; and the corresponding capillary suction time (CST) reduction efficiency increased 49.29 % (1 h FNA treatment + 1 h LZM treatment) and 52.98 % (6 h FNA treatment + 1 h LZM treatment). A comprehensive investigation conducted in this study revealed the underlying mechanism of dewaterability improvement lies in the transformations of extracellular polymeric substances (EPS). The combined conditioning led to enhanced hydrophobicity in the sludge, as suggested by FTIR protein secondary structure and interfacial free energy. The reduced zeta potential and the potential barrier indicated the reduction of the repulsive force of sludge particles and the bound water content in the conditioned floc. The hydrophobicity, flow permeability and flocculability were enhanced after combined treatment, leading to the release of bound water.

Enhanced mesophilic fermentation of waste activated sludge by integration with in-situ nitrate reduction

This study investigated the reduction of nitrate in a mesophilic waste activated sludge (WAS) fermentation system and determined the effect of nitrate reduction on the hydrolysis, acidogenesis and acetogenesis. Experimental results showed that the initial nitrate concentrations of 100, 200 and 400 mg/L were completely reduced in 1, 2 and 7 days, respectively. The destruction of volatile suspended solids was 1.2, 1.8 and 2.8 times, respectively, that without nitrate, demonstrating nitrate promoted the release of organic matter in sludge and enhanced the biodegradability of sludge organics. Moreover, batch tests using model substrates illustrated nitrate reduction promoted sludge hydrolysis and acetogenesis, but slightly inhibited acidogenesis. This study offers a feasible method to address two major problems currently faced by biological wastewater treatment plants, i.e. the overabundance of WAS and the lack of carbon sources for the denitrification process.

A novel gravity sedimentation - Forward osmosis hybrid technology for microalgal dewatering

A novel gravity sedimentation - forward osmosis (G-FO) hybrid reactor was built up for separating and concentrating the biomass from the algal-rich water (microalgal dewatering). The extracellular organic matter (EOM) from Chlorella vulgaris (C. vulgaris) was divided into dissolved EOM (dEOM) and bound EOM (bEOM). Water flux, flux recovery rate and moisture content (MC) were investigated. Through sedimentation rate, zeta potential and hydrophilicity/hydrophobicity to analyze the experimental results. Scanning electronic microscopy (SEM) was used to observe the different morphologies of accumulated algae cells and EOM on the surface of the membrane. The results showed that cell + bEOM solution had the fastest sedimentation rate and fewest negative charge, so the pollutants accumulated more easily on the membrane surface, resulting in the highest flux decline. Its algal cake layer was the densest from the view of SEM. Cell + bEOM + dEOM solution had the lowest flux decline and the cake layer was the loosest. Cell + bEOM solution had the most severe irreversible fouling and the lowest flux recovery rate (FRR). The membrane fouling of cell solution was lower than that of cell + bEOM + dEOM solution, and the FRR of cell solution was almost 100%. According to the nonionic macro-porous resin fraction results of EOM, cell + bEOM + dEOM solution contained more hydrophilic components, resulting in the lowest MC. On the contrary, cell + bEOM solution showed the highest MC, which contained more hydrophobic components. Effects of bEOM and dEOM on microalgae dewatering performance of a novel gravity sedimentation - forward osmosis (G-FO) hybrid system were investigated, which provided a theoretical basis for large-scale application of FO technology for microalgae dewatering.

Triple action of FeCl3-assisted hydrothermal treatment of digested sludge for deep dewatering

In this study, a FeCl₃-assisted hydrothermal treatment (HTT) process under mild conditions (90 °C-130 °C) was developed for deep dewatering of anaerobically digested sludge. HTT of sludge at 90 °C-130 °C with 4%-6% Fe³⁺ ions loading based on total sludge solids followed by mechanical dewatering reduced sludge water content from 82% to 38%-53% and sludge weight by 62%-72%. The treatment increased the flowability of sludge through reduction of apparent viscosity and disintegration of colloidal forces between sludge particles. This study unveiled that FeCl₃-assisted HTT process had three mechanisms for improving sludge dewaterability and flowability. The treatment hydrolysed sludge flocs in the presence of Lewis acid FeCl₃ and high temperature (90-130 °C). Fe³⁺ ions also improved dewaterability through the formation of double electric layers and neutralisation of surface negative charges, leading to flocculation of sludge flocs. More importantly, the hydrolysed sludge components produced during HTT process acted as reducing agents and led to in-situ generation of iron oxyhydroxide nanoparticles through reduction-oxidation reactions, further enhancing flocculation/co-precipitation of sludge flocs. The treatment reduced EPS content and changed conformational structures of EPS proteins by breaking down hydrogen bond-maintaining α-helix which led to a loose EPS protein structure and enhanced hydrophobicity and flocculability. Furthermore, the FeCl₃-assisted treatment promoted immobilisation of the majority of heavy metals in the sludge matrix through co-precipitation/complexation reactions with iron species and organic/inorganic matters. This indicates that the FeCl₃-assisted treatment reduced direct toxicity/bioavailability of the majority of heavy metals and the treated sludge may be suitable for land application. Overall, this study provides new insights into mechanism of FeCl₃-assisted HTT process for dewaterability of anaerobically digested sludge and immobilisation of heavy metals.

Unraveling the behavior of nitrite on promoting short-chain fatty acids accumulation from waste activated sludge by peracetic acid pretreatment: Extracellular polymeric substance decomposition and underlying mechanism

Peracetic acid (PAA) is an emerging oxidant for waste activated sludge (WAS) treatment due to its strong oxidization and few toxic byproducts. Nitrite which can be in-situ recovered from WAS fermentation liquor, its protonated form (free nitrous acid, FNA) is regarded as the cost-effective inactivator. The stubborn extracellular polymeric substance (EPS) is the rate-limiting step for energy/resource recovery from WAS. This work found that the co-pretreatment of PAA and FNA can effectively promote short-chain fatty acids (SCFAs) production during anaerobic fermentation. Higher PAA dosage (100 mg/g VSS, FP4WAS) in co-pretreatment was beneficial for organics release (1976.9 mg COD/L), remarkably increased by 10.3- 96.5 % than that of low PAA dosage (25- 75 mg/g VSS), and promoted by 105.1 % and 62.1 % than FNA (FWAS)/PAA (100 mg/g VSS, P4WAS)-pretreated WAS. Effective release of soluble organics contributed to the SCFAs accumulation (7679 ± 86 mg COD/L, 4 d), enhanced by 200.0 % and 19.0 % than FWAS and P4WAS, respectively. Acetic (HAc) and propionic acid (HPr) peaked at 6344.7 mg COD/L in FP4WAS (accounted for 82.6 %), which increased by 10.6- 899.0 % than other groups. Moreover, OH and O₂^- were detected in co-pretreatment, may play the synchronous effect with the crucial intermediates of NO, NO₂ and ONOO^-/ONOOH on EPS decomposition.

A novel pre-magnetized ZVI/PS pretreatment for improving sludge dewaterability: The role of EPS fractions

The dewaterability of waste-activated sludge (WAS) has been extensively examined using zero-valent iron (ZVI)-based advanced oxidation processes (AOPs). However, the high dosage and low utilization efficiencies of ZVI cast doubt on the dependability and viability of ZVI-based AOPs. In this study, we successfully demonstrated pre-magnetization as an efficient, chemical-free, and ecological method for improving the efficiency of sludge dewatering by ZVI/persulfate (PS) process, in which the reduction ratios of capillary suction time (CST) and specific resistance to filtration (SRF) increased by 8.67% and 11.06% under optimal conditions, respectively. The highly active Fe²⁺ released during ZVI corrosion may be more essential than ZVI itself during PS activation, which could be strengthened by pre-magnetization. Both homogeneous and heterogeneous Fe²⁺ could react with PS to produce aqueous hydroxyl radicals (∙OH) and sulfate radicals (SO₄^-∙) as well as surface-bound ∙OH and SO₄^-∙, further decomposing bound-extracellular polymeric substances fractions, broking hydrophilic functional groups and compounds, altering protein secondary structure to expose more hydrophobic sites, and releasing abundant EPS-bound water. Due to the protection of tightly-bound extracellular polymeric substances (TB-EPS) and the competitive oxidation of organics released during the early disintegration stage, radical oxidation primarily occurs at extracellular levels, releasing a bit of intracellular water. Besides, polysaccharides in TB-EPS may function a more significant role in flocculation than proteins, and a porous structure favorable to drainage will be formed after the pre-magnetized ZVI/PS treatment. The cost-benefit analysis further reveals that the Pre-ZVI/PS process presents high reusability and utilization, making it potential for particle application in sludge dewatering.

Methane production from peroxymonosulfate pretreated algae biomass: Insights into microbial mechanisms, microcystin detoxification and heavy metal partitioning behavior

This study investigated the methane production potential of algal biomass by anerobic digestion with the addition of peroxymonosulfate (PMS), the removal of microcystin were analyzed and discussed. The microcystin concentration in the collected algal sludge was 1.20 μg/L in the liquid phase and 1393 μg/g in the algal sludge before anaerobic fermentation. The microcystin concentration decreased to 0.20-0.35 μg/L in the liquid phase and 4.16-11.51 μg/g in the sludge phase after 60 days of digestion. The initial PMS dose and residue microcystin concentration could be simulated with a logarithmic decay model (R² > 0.87). Anaerobic digestion could recover energy from algal source in the form of methane gas, which was not affected in the presence of microcystin, and the microcystin removal rate was >99%. Digestion decreased the total contents of Cd and Zn in the liquid phase and increased the total contents of Cr and Pb in the liquid phase. The microbial community and function prediction results indicated that the PMS0.1 system had the highest methane production, which was attributed to the high abundance of Mechanosaeta (40.52%). This study provides insights into microbial mechanisms, microcystin detoxification and the heavy metal partitioning behavior of the algal biomass during methane production.

Electrochemical impedance spectroscopy (EIS) reveals the role of microbial fuel cell-ceramic membrane bioreactor (MFC-CMBR): Electricity utilization and membrane fouling

Ceramic membrane has become a major concern due to creasing cost and competitive efficiency. Microbial fuel cell-ceramic membrane bioreactor (MFC-CMBR) is considered alternative technology for larger-scale industrial application because of its advantages of convenient detecting and control of membrane fouling. However, MFC-CMBR are highly susceptible to membrane fouling and harsh operating requirements in these wastewaters of different compositions. This research critically discusses that electrochemical response in different types of MFC-CMBRs and control of electricity utilization on ceramic membrane fouling. The experimental results indicated that the application of sludge acclimated in coupling system with higher external resistance could ensure that lower costs (electricity utilization and membrane cleaning) provided enough membrane fouling control. The improved performance of MFC-CMBR-1 could be attributed to its enhanced nitrification/denitrification activity and capacity of electrons migration between electrode and sludge mixture. The coupling system alleviated membrane fouling and impedance increasing by improving the characteristics of sludge (increased particle size, decreased adsorption adhesion free energy), EPS (decreased hydrophobicity, molecular weight distribution regulation). And filtration tests showed that roughness and contact angle for the MFC-CMBR tend for better development compared to CMBR, dependent on the changes in the chemical surface groups as a result of electric distribution ratio. In addition, correlation analysis and filtration experiments showed that the extracellular polymer substances (EPS) enhanced the charge transfer resistance (R_ct), and the protein substance in EPS was the main fouling substance when external resistance was close to the internal resistance of MFC. In summary, the low internal resistance of ceramic membrane lead to obvious better fouling control and electricity utilization than organic membrane, and the paper provides insight into the MFC-CMBR systems for a wide range of detecting membrane fouling and applications of membrane fouling mitigation.

Rhamnolipid increases H2S generation from waste activated sludge anaerobic fermentation: An overlooked concern

Rhamnolipid (RL), one representative biosurfactant, is widely regarded as an economically feasible and environmentally beneficial additive to improve fermentation efficiency and resource recovery from waste activated sludge (WAS). However, its potentially detrimental impact on WAS fermentation such as H₂S generation was overlooked previously. This study therefore aims to fill the gap through exploring whether and how the presence of RL affects H₂S generation from WAS anaerobic fermentation. Experimental results showed that when RL increased from 0 to 40 mg/g total suspended solids (TSS), the cumulative H₂S yield enhanced from 323.6 ×  10^-4 to 620.3 ×  10^-4 mg/g volatile suspended solids (VSS). Mechanism analysis showed that RL reduced WAS surface tension, which benefited transformations of organic sulfurs (e.g., aliphatic-S and sulfoxide) and inorganic sulfate from solid to liquid phase. The presence of RL not only reduced the ratio of α-helix/(β-sheet + random coil) and damaged the hydrogen bonding networks of organic sulfurs but also promoted substrate surface charges and cell membrane permeability. These facilitated the contact between hydrolase and organic sulfurs, thereby increasing sulfide production from organic sulfurs hydrolysis. Further investigations showed that RL promoted the expression of key genes (e.g., aprA/B and dsrA/B) involved in the dissimilatory sulfate reduction, which accelerated the reaction of adenosine 5'-phosphosulfate (APS)→ sulfite→ sulfide. Meanwhile, RL inhibited the corresponding key genes such as CysH, and Sir, responsible for assimilatory sulfate reduction (APS→3'-phosphoadenosine-5'phosphosulfate→organosulfur), which reduced substrate competition in favor of H₂S production from dissimilatory sulfate reduction. Besides, RL decreased the fermentation pH, which benefited the transformation of HS^- to H₂S.

Ferric chloride aiding nitrite pretreatment for the enhancement of the quantity and quality of short-chain fatty acids production in waste activated sludge

The production of short-chain fatty acids (SCFAs) via anaerobic fermentation of waste activated sludge (WAS) is often limited with poor quality of SCFAs and long fermentation time. To overcome these issues, we provided an efficient strategy by using ferric chloride (FC) to aid nitrite pretreatment. Experimental results showed that the maximal SCFAs production of 211.3 ± 3.1 mg COD/g VS was achieved with 4 mmol/L of FC integrated with 250 mg/L of nitrite pretreatment on day 5, which was 4.1-fold higher than that of the blank control (52 ± 5 mg COD/g VS, day 7). Besides, the enrichment of acetic acid was observed in the combined system, which accounted for 54.6 ± 3.5% of total SCFAs, while the proportion was only 31.5 ± 4.9% in the blank control. Propionic acid, isobutyric acid, n-butyric acid, n-valeric acid and isovaleric acid accounted for 14.7 ± 1.5%, 6.9 ± 1.4%, 7.4 ± 1.5%, 13.1 ± 1.0%, and 3.3 ± 1.5% of total SCFAs in the combined system and 22.8 ± 4.0%, 11.9 ± 3.0%, 6.7 ± 3.1%, 17.6 ± 2.0%, and 9.5 ± 3.9% of total SCFAs in the blank control, respectively. It was found that soluble proteins and carbohydrates in the combined system were higher than those in the blank control, suggesting that FC and nitrite pretreatment was beneficial for WAS disintegration. The fluorescence spectrum results suggested that FC and nitrite pretreatment improved the biodegradability of released organics, which provided more biodegradable substances for the subsequent SCFAs production. This was because the addition of FC induced the formation of free nitrous acid from nitrite. Besides, FC-induced iron reduction also promoted the conversion of recalcitrant organics to biodegradable organic matter. Microbial community structure analysis demonstrated that the functional bacteria involved in acetogenesis process such as Enterococcus, Proteiniclasticum, and Petrimonas were highly enriched due to the pretreatment of FC and nitrite, indicating this method could improve the relative abundance of SCFAs producers. Overall, this study revealed that the pretreatment of FC and nitrite promoted the formation of free nitrous acid and increased the yield of SCFAs, which provided a novel method for wastewater treatment plants to ameliorate the sewage treatment craft and rationally use the existing substances in WAS to enhance resource recovery.

A novel approach using protein-rich biomass as co-fermentation substrates to enhance phosphorus recovery from FePs-bearing sludge

A novel approach for the enhancement of phosphorus (P) recovery from Fe bound P compounds (FePs)-bearing sludge by co-fermentation with protein-rich biomass (PRB) is reported. Four PRBs (silkworm chrysalis meal, fish meal, corn gluten meal, and soya bean meal) were used for co-fermentation. The results revealed that PRBs with strong surface hydrophobicity and loose structure favored the hydrolysis and acidogenesis processes. Sulfide produced by PRB could react with FePs to form FeS and promote P release. Due to the neutralization of volatile fatty acids (VFAs) by a relatively high concentration of ammonia, the pH was maintained near neutral and thus prevented the dissolution of metal ions (e.g., Fe and Ca). This was beneficial to save the cost of subsequent P recovery and form high-purity struvite. Compared with the control, the soluble orthophosphate and VFAs increased by 88.3% and 531.3%, respectively, in the co-fermentation system with silkworm chrysalis meal. Cysteine was the important intermediate. The metagenomics analysis indicated that the gene abundances of phosphate acetyltransferase and acetate kinase, which were key enzymes in the acetate metabolism, increased by 117.7% and 52.2%, respectively. The gene abundances of serine O-acetyltransferase and cysteine synthase increased by 63.4% and 54.4%, respectively. Cysteine was primarily transformed to pyruvate and sulfide. This study provides an environment-friendly strategy to simultaneously recover P and VFAs resources from FePs-bearing sludge and PRB waste.

Decrease the effective temperature of hydrothermal treatment for sewage sludge deep dewatering: Mechanistic of tannic acid aided

The formation of refractory compounds and high nitrogen concentrations in filtrates is the bottleneck of hydrothermal treatment (HT) for sludge deep dewatering. To simultaneously solve these two problems, tannic acid (TA)-aided HT was firstly developed in this study. TA addition improved dewaterability under all investigated HT temperatures by improving the sludge relative hydrophobicity. Moreover, the effective HT temperature was reduced from 180 to 160 ℃. The soluble extracellular polymeric substances (S-EPSs) of the sludge hydrothermally treated at 160 ℃ under the optimal TA dose (0.15 mmol/g total solids) contained 47.27% less total organic nitrogen than the S-EPSs of the raw sludge. This result means that the corresponding filtrate contained lower concentrations of refractory compounds and nitrogen than those under the conventional HT conditions and thus could be more easily treated. Furthermore, the changes in the protein secondary structure and the interaction of TA with high-molecular-weight (HMW) proteins in S-EPSs were found to be highly relevant (p < 0.05) to the improvement of sludge dewaterability. With increasing HT temperature (120-180 ℃), the S-EPS HMW proteins with numerous hydrophilic functional groups (hydroxyl and carboxyl) were hydrolyzed, and their secondary structures unfolded; consequently, more sites were exposed for hydrophobic binding with TA, and the TA-protein interaction was more stable and spontaneous. The precipitation of protein with TA also increased with the HT temperature. Thus, TA-aided HT improves protein precipitation and sludge dewaterability through protein structure destruction and the production of more hydrophobic binding sites for TA. The identification of the influencing mechanisms on SS EPS-TA interaction mode and binding capacity are conducive to the further upgrading of TA-aided HT for engineering applications.

Gravity settling and centrifugation increase the acid buffer capacity of activated sludge

Buffer capacity is a critical parameter in sludge management of domestic wastewater treatment plants that determines acid/base usage. It is here shown that gravity settling or centrifugation significantly increased the buffer capacity in the supernatant of the sludge. The sludge thickening considerably elevated the total alkalinity of the sludge from 16.0 to 31.5 mgCaCO₃ taking pH 5.0 for example with the sludge concentration times increasing from 2 to 20 times, while insignificantly affected the total acidity (initial 335.3 vs 240.2 mgCaCO₃ at concentration times of 10 considering pH increased to 11.0). These findings indicate that the inherent buffer in sludge can be released during sludge thickening and the primary component of this buffer is alkalinity. The released buffer may be correlated to a negative surface charge inside sludge flocs, as it consumed base in titration. The increased buffer capacity in supernatant could be due to the buffer released from bound water to free water, and in particular, from the release of interstitial water, an important part of the bound water. Further mechanism analysis suggested that the increased buffer capacity in thickened sludge could relate to extracellular polymeric substances, for which more studies are needed. Overall, this study for the first time reports that sludge thickening can change the buffer capacity of sludge, affecting the efficiency and acid/base usage of sludge treatment.

A comprehensive study on simultaneous enhancement of sludge dewaterability and elimination of polycyclic aromatic hydrocarbons by Fe2+ catalyzing O3 process

Simultaneous removal of polycyclic aromatic hydrocarbons (PAHs) in the process of enhancement of sludge dewaterability via oxidation of hydroxyl radicals (•OH) and flocculation of Fe³⁺ by Fe²⁺-catalyzing O₃ were investigated as a novel research focus. The results showed that capillary suction time (CST) and water content of dewatered sludge cake (Wc) were reduced from 57.9 s and 85.1% to 13.6 s and 69.65% under the optimum usage of 60 mg/g dry solids (DS) O₃ and 80 mg/g DS FeSO₄, respectively. The relevant dewatering mechanism of Fe²⁺-catalyzing O₃ treatment was elucidated. It was found that extracellular polymeric substances-bound (EPS-bound) and intracellular water was dramatically released through destroying sludge cells and EPS gel-like structure by produced •OH. In addition, the results of X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) and ¹³C NMR spectroscopy revealed that •OH oxidized and mineralized hydrophilic organic matters intensifying hydrophobicity of sludge surface. Moreover, Fe³⁺ generated by oxidation of Fe²⁺ agglomerated fragmented fine particles into large aggregates and decreased exposure of hydrophilic sites by neutralizing negative charge, which promoted water-solids separation. Meanwhile, sludge surface roughness was decreased which was determined by material type upright confocal laser microscope (CLM). As a consequence, •OH and Fe³⁺ were mainly responsible for enhancement of sludge dewaterability. Moreover, more than 40% of removal rate of PAHs was accomplished by Fe²⁺-catalyzed O₃ treatment mitigating the environmental risks of PAHs spread.

Carboxymethyl cellulose stabilized ferrous sulfide@extracellular polymeric substance for Cr(VI) removal: Characterization, performance, and mechanism

Iron-based materials, especially ferrous sulfide (FeS), effectively remediate chromium pollution. However, the agglomeration of FeS reduces its reactivity to chromium. Herein, carboxymethyl cellulose stabilized ferrous sulfide@extracellular polymeric substance (CMC-FeS@EPS) was developed to remove hexavalent chromium (Cr(VI)) from water. CMC-FeS@EPS (98.00%) exhibited excellent removal efficiency of 40 mg/L Cr(VI) than those of FeS (57.35%) and CMC-FeS (68.60%). CMC-FeS@EPS showed good removal efficiency of Cr(VI) in wide pH range (from 4 to 9) and the co-existence of ions. FTIR and XPS results demonstrated that EPS functional group accelerated the process of adsorption and precipitation. Electrochemical results showed that CMC-FeS@EPS transferred electrons to Cr(VI) faster than CMC-FeS. In total, this study started from a new idea of using EPS to improve the performance of CMC-FeS, and provided a simple and effective way to remediate chromium pollution without secondary pollution.

The three-stage effect of hydrothermal treatment on sludge physical-chemical properties: Evolution of polymeric substances and their interaction with physicochemical properties

Hydrothermal treatment (HT) is effective for the deep dewatering of sewage sludge (SS); however, the effective temperature generally exceeds 180 ℃, resulting in the production of refractory compounds in the sludge filtrates. To explore a new process based on HT, achieving ideal dehydration efficiency at lower temperatures, it is essential to identify the key sludge dewatering mechanism under different HT stages. In this study, the relationship between the properties of sludge polymeric substances (components and molecular structures) and the physical-chemical properties of sludge flocs during HT (120-260 ℃) was investigated. The results indicated that the SS surface hydrophilicity/hydrophobicity was mainly responsible for sludge dewaterability in the solubilization (120 ℃) and hydrolyzation stages (140-180 ℃), while the mechanically bound water and capillary force were the main limiting factors of sludge dewaterability during the carbonization stage (200-260 ℃). Moreover, in the solubilization stage (120 ℃), a plenty of high-Mw (Mw > 70 kDa) polymeric substances with numerous hydrophilic functional groups and a compact structure were released from the intracellular region to the outer layer, which improved the hydrophilicity of sludge floc surface and deteriorated the sludge dewaterability. With the hydrolysis of the polymeric substances (140-180 ℃, hydrolyzation stage), the destruction of proteins secondary structures and peptide chains exposed more hydrophobic groups, resulting in the release of bound water and improvement of sludge dewaterability. At HT temperatures of 200-260 ℃ (carbonization stage), dehydration and amine aldehyde condensation occurred, benefiting the formation of fixed carbon and smooth morphology structure of SS, reducing the capillary force-induced water-holding capacity of sludge flocs. The establishment of the three-stage influencing theory and the identification of key influencing factors are conducive to the further regulation and upgrading of HT.

Improving methane production from algal sludge anaerobic fermentation by peroxydisulfate (PDS) pretreatment

This study investigated the potential of improving methane production from algal sludge anaerobic digestion by peroxydisulfate (PDS) pretreatment. The results show that with PDS dosage at 0.02 g PDS/g algal sludge TSS, PDS added system has highest accumulative methane production after 60 days fermentation. The accumulative methane production was 1.08, 1.15, 1.14, 1.13, 1.08, 0.76, and 0.15 times as compared with control, at 0.01, 0.02, 0.05, 0.1, 0.2, 0.5, and 1 g PDS/g algal sludge TSS added, respectively. The SCOD in the system was keep increasing with the increment of PDS dosage after 120 min pretreatment. The algal sludge dewatering rate was increased with adding of PDS as pretreatment. The addition of PDS has inhibited the activities of microbes involved in digestion, while the short chain fatty acids production was improved after 3 days digestion. One-substrate model can be used to simulate the methane yield. The hydrolysis rate was decreased after dosing with PDS, while highest actual and predicted accumulative methane yield was occurred at 0.02 g PDS/g algal sludge TSS. Proteobacteria has higher percentage when the PDS was not higher than 0.1 g PDS/g algal sludge TSS, Acetothermia has higher percentage at 0.01 g PDS/g algal sludge TSS. The microcystin-LR (MC-LR) in algal sludge was largely removed after digestion, including the intracellular MC-LR. The higher PDS dosage could cause heavy metal release from algae cell to the digestate during fermentation. The addition of PDS to algal sludge can improve the accumulative methane production and mitigate microcystin concentration.

Insight into the roles of electrolysis-activated persulfate oxidation in the waste activated sludge dewaterability: Effects and mechanism

Sludge dewatering, as one of the most important steps of sludge treatment, can facilitate transportation and improve disposal efficiency by reducing the volume of sludge. This study investigated the effects of electrolysis-activated persulfate oxidation on improving sludge dewaterability. The results indicated that the sludge capillary suction time (CST) and water content of dewatered sludge cake (Wc) reduced from 93.7 s and 87.8% to 9.7 s and 68.3% respectively at the optimized process parameters: electrolysis voltage of 40 V, electrolysis time of 20 min, and 1.2 mmol/g TS S₂O₈^2-. Correlation analysis revealed that the enhancement of sludge dewaterability was closely associated with the increased floc size and zeta potential, decreased protein content in three-layers extracellular polymeric substances (EPS) and viscosity (R = -0.868, p = 0.002; R = -0.703, p = 0.035; R ≥ 0.961, p < 0.001; R = 0.949, p < 0.001). Four protein fluorescence regions in EPS were analyzed by three-dimensional excitation-emission matrix parallel factor (3D-EEM-PARAFAC). The protein secondary structure was changed after the treatment, and the reduction of α-helix/(β-sheet + random coil) indicated that more hydrophobic sites were exposed. Analysis by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) and rheological test demonstrated that the hydrophilic functional groups of the sludge were decreased and the sludge mobility was significantly enhanced after the treatment with electrolysis-activated persulfate oxidation. Moreover, bound water was converted to free water during SO₄·^- and ·OH generated by electrolysis-activated persulfate degraded EPS and attacked sludge cells. Meanwhile, scanning electron microscopy (SEM) images revealed that the treated sludge formed porous channel structures, which promoted the flowability of the water. These findings provide a new insight based on electrolysis-activated persulfate oxidation in sludge treatment for enhancing sludge dewaterability.

Post-treatment options for anaerobically digested sludge: Current status and future prospect

Anaerobic digestion is the most commonly used sludge treatment technology in large-scale wastewater treatment plants (WWTPs), generating two main products, i.e., biogas and anaerobically digested (AD) sludge. Biogas can be used as a source of renewable energy, and AD sludge is often transported for agricultural land application. Land application of AD sludge is confronted with ever-increasing economic and regulatory pressures due to its high water content, high organic content and related odour and pathogen content (if poorly stabilized), as well as potential toxic metal and organic contaminants. To address these challenges, a number of technologies have been developed for the further treatment of AD sludge before final disposal. This review aims to critically evaluate these state-of-the-art technologies. These technologies were categorized based on their primary aims: 1) dewaterability enhancement; 2) solids reduction and stabilization; 3) toxic metals removal. At present, the goal of post-treatment mainly focuses on dewaterability enhancement, to reduce transport costs. In future, we propose that the post-treatment of AD sludge should orient towards multiple aims, i.e., an integrated approach enabling sludge volume reduction, stabilization (including pathogen removal), and metal solubilization simultaneously. Two promising technical routes are suggested as examples, i.e. physio-chemical iron-based advanced oxidation and biological acidic aerobic digestion, while more approaches need to be developed in future studies. We concluded that post-treatment of AD sludge will promote the AD sludge management towards a more economically favourable, socially acceptable, and environmentally sustainable way; however, further development and rigorous evaluation are required for a wider adoption.

Enhanced methane production from anaerobic digestion of waste activated sludge through preliminary pretreatment using calcium hypochlorite

Methane recovery from waste activated sludge (WAS) through anaerobic digestion is generally restricted by the poor degradability of WAS. Herein, a novel sludge pretreatment technology by using the calcium hypochlorite (Ca(ClO)₂) in enhancing the methane production from WAS anaerobic digestion was reported. The solubilization of WAS was significantly increased after 10-240 mg Ca(ClO)₂/g VS (VS: volatile solids) pretreatment for 48 h, under which the solubilization was 1.7-3.4 folds (i.e., 0.17-0.34 mg SCOD/mg VS; SCOD: soluble chemical oxygen demand) higher than that without Ca(ClO)₂ pretreatment (i.e., 0.1 mg SCOD/mg VS). Correspondingly, the methane production was increased from 250.0 ± 5.3 mL/g VS to 385.1 ± 3.3 mL/g VS with the doses of Ca(ClO)₂ increasing from 10 mg/g VS to 240 mg/g VS, resulted in an increasing methane production of 3.6%-59.7% than that without Ca(ClO)₂ pretreatment. The microbial community composition results exhibited that the populations of key acidogens (e.g., Longilinea sp.) and methanogens (e.g., Methanosaeta sp.) were both reduced significantly. Moreover, Ca(ClO)₂ decreased the cells viability, leading to a 76.2% reduction of living cells fraction. Accordingly, it was further confirmed that high dosage of Ca(ClO)₂ could inhibit three microbial-related processes relevant to methane production, i.e., acidification, hydrolysis and methanogenesis.

Electrical impedance spectroscopy as a potential tool to investigate the structure and size of aggregates during water and wastewater treatment

Microscopic structure and size are important metrics for estimating aggregates environmental behaviors during water and wastewater treatment. However, in-situ determination of these characteristics is still a challenge. Here, we drew inspiration from a block disassembly process to propose an electrical impedance spectroscopy (EIS) method and constructed a generalized framework to associate macroscale electrical properties with microscopic structure and size-related characteristics of aggregates of different hierarchies. Extracted via EIS, the proposed models were verified to be capable of describing the self-similarity of aggregates and capturing the fractal and size information. Further, the proposed models exhibited a wide range of applications, which agrees well with the data gathered from various activated sludges, other colloids, and microgels in water and wastewater treatment. Finally, the EIS method was achieved online monitoring of fractal dimension and floc size during a sludge pre-oxidation conditioning process, which was elected as an example to illustrate the potential online applications of this EIS method in real water and wastewater environment. The obtained on-line data were used to indicate the potential suitable oxidation time during sludge pre-oxidation conditioning. These observations may inspire new methods of quantifying the aggregate structure and promote intelligent and dynamic decision-making during water and wastewater treatment.

The Ionic Liquid-H2O Interface: A New Platform for the Synthesis of Highly Crystalline and Molecular Sieving Covalent Organic Framework Membranes

Covalent organic frameworks (COFs) are highly porous crystalline polymers with uniform pores and large surface areas. Combined with their modular design principle and excellent properties, COFs are an ideal candidate for separation membranes. Liquid-liquid interfacial polymerization is a well-known approach to synthesize membranes by reacting two monomers at the interface. However, volatile organic solvents are usually used, which may disturb the liquid-liquid interface and affect the COF membrane crystallinity due to solvent evaporation. Simultaneously, the domain size of the organic solvent-water interface, named the reaction zone, can hardly be regulated, and the diffusion control of monomers for favorable crystallinity is only achieved in the water phase. These drawbacks may limit the widespread applications of liquid-liquid interfacial polymerization to synthesize diverse COF membranes with different functionalities. Here, we report a facile strategy to synthesize a series of imine-linked freestanding COF membranes with different thicknesses and morphologies at tunable ionic liquid (IL)-H₂O interfaces. Due to the H-bonding of the catalysts with amine monomers and the high viscosity of the ILs, the diffusion of the monomers was simultaneously controlled in water and in ILs. This resulted in the exceptionally high crystallinity of freestanding COF membranes with a Brunauer-Emmett-Teller (BET) surface area up to 4.3 times of that synthesized at a dichloromethane-H₂O interface. By varying the alkyl chain length of cations in the ILs, the interfacial region size and interfacial tension could be regulated to further improve the crystallinity of the COF membranes. As a result, the as-fabricated COF membranes exhibited ultrahigh permeance toward water and organic solvents and excellent selective rejection of dyes.

Destroying the structure of extracellular polymeric substance to improve the dewatering performance of waste activated sludge by ionic liquid

The disposal and resource utilization of waste activated sludge (WAS) is a big challenge for its high moisture content. Ionic liquid (IL), 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM][OTf]), was innovatively used as a conditioner to improve the dewatering performance of WAS. The WAS was characterized by flocs size, three-dimensional excitation-emission matrix (3D-EEM), zeta potential, Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM) for the investigation of intensification mechanism. The results showed that the dewatering performance of WAS conditioned by [EMIM][OTf] was significantly improved. The moisture content was successfully decreased to 64.99±0.92 %, and the intensification mechanism was investigated. The results showed that the structures of extracellular polymeric substance (EPS) were destroyed by [EMIM][OTf]. It brought a sharp decrease of the contents of polysaccharides (PS), proteins (PN), humic acid (HA) and fulvic acid (FA) in tightly bound extracellular polymeric substance (TB-EPS) structure. The inactivation of microbial cells promoted the disintegration of flocs. Large flocs were converted into unstable small particles and biopolymers. In addition, the negative charges of WAS were also neutralized for dissolution of biopolymers in [EMIM][OTf], and the electrostatic repulsion between flocs was weakened. [EMIM][OTf] was easily recycled five times. The research results indicate that specific IL, such as [EMIM][OTf], is a potential conditioner to improve the dewatering performance of WAS.

Revealing the heating value characteristics of sludge-based hydrochar in hydrothermal process: from perspective of hydrolysate

Hydrothermal treatment (HT) is a promising method to convert sewage sludge to hydrochar biofuel. The heating value is directly correlated to the carbon content in hydrochar; however, the release of organic matter from sludge to hydrolysate and the transfer of the Maillard reaction products generated in the hydrolysate to the solid phase alter the carbon content in hydrochar. In this study, the relationship between hydrolysate and heating value of sludge-based hydrochar was presented, aiming to explain how the calorific value of hydrochar was affected by HT conditions. We adopted a direct combustion test to verify its clean combustion features. Hydrochar derived at 260 °C and residence time of 4 h (HC 260-4) exhibited the highest calorific value (HHV_daf = 26.23 MJ/kg) with an energy density of 1.43, and its fuel characteristics were similar to those of lignite. The increase in the HT temperature and residence time up to 260 °C and 4 h, respectively, was beneficial for enhancing HHV_daf. Conversely, further increase of the HT temperature to 300 °C and HT time to 6 h yielded a decrease in HHV_daf. Investigation of the underlying mechanism revealed that the protein and polysaccharide releasing from sludge to hydrolysate occurred the Maillard reaction (MR). The generated humic-like Maillard reaction product (MRP) was transferred to hydrochar, inducing an increase in the carbon content and calorific value and a decrease in the organic content of hydrolysate. As the carbohydrate content in the hydrolysate decreased, the MR was terminated, so no more MRP was transferred to hydrochar. At the same time, the protein was still continuously released at higher temperatures and longer residence times, yielding a decline in the HHV_daf. Moreover, clean energy utilization was verified from the reduced nitrogen content in hydrochar and lower CO and NO_x emission of HC 260-4 in the combustion test. After the HT, increased hydrophobicity and a lower fraction of bound water improved the dewaterability, which is of great significance for applying hydrochar as biofuel. The findings of this study provided a new perspective to explain the heating value generation of hydrochar and more direct evidence to assess its clean combustion properties, with promising perspectives for practical applications.

Compact wastewater treatment process based on abiotic nitrogen management achieved high-rate and facile pollutants removal

Chemically enhanced primary treatment (CEPT), ammonium ion exchange and regeneration (AIR) and membrane bioreactor (MBR) were coupled as CAIRM to treat domestic wastewater compactly and efficiently. CAIRM achieved efficient removal of chemical oxygen demand, ammonia nitrogen, total nitrogen (TN) and total phosphorus with total hydraulic retention time of 4.6 h, and obtained 2.3 ± 0.9 mg/L TN in the effluent. CEPT removed phosphate and impurities and prevented AIR from pollution. AIR maintained excellent nitrogen removal with a slight decrease in the exchange capacity of ion exchangers. MBR polished the effluent from AIR, and the larger particle size and better dewaterability of sludge mitigated the membrane fouling. Many heterotrophic genera, such as Rhodobacter and Defluviimonas, were enriched in the oligotrophic MBR. This study demonstrates the viability and stability of CAIRM in efficient wastewater treatment, which will address critical challenges in insufficient nitrogen removal and high land occupancy of current processes.

Understanding the interaction between triclocarban and denitrifiers

The widespread use of triclocarban (TCC) has led to its substantial release into aquatic environment. As an important microbial community in wastewater treatment, denitrifying cultures likely remove TCC and also may be affected by TCC which has not been revealed. This work therefore aims to add knowledge to these questions. Experimental results showed that 71.2 %-79.4 % of TCC was removed by denitrifying sludge in stable operation when TCC concentration was 1∼20 mg/L. Mass balance analyses revealed that TCC was dominantly removed by adsorption rather than biodegradation, and non-homogeneous multilayer adsorption was responsible for this removal, with hydroxyl groups, amides and polysaccharides acting as the possible adsorption sites. Although the physicochemical properties of denitrifying cultures were unaffected after short-term exposure, long-term exposure to TCC deteriorated the settleability, dewaterability, flocculability and hydrophobicity of denitrifying biomass. It was observed that 20 mg/L TCC decreased denitrification efficiency by 70 % in long-term operation. Mechanism studies revealed that long-term exposure to TCC resulted in the increase of extracellular polymeric substances especially proteins, and the decrease of denitrifiers' activities. High-throughput sequencing revealed that TCC decreased the diversity of microbial community and the abundances of denitrifier genera such as Hyphomicrobium, Paracoccus, Saprospiraceae and unclassified-f-Rhodocyclaceae.

A novel strategy for improving volatile fatty acid purity, phosphorus removal efficiency, and fermented sludge dewaterability during waste activated sludge fermentation

Volatile fatty acids (VFAs) from waste activated sludge (WAS) via alkaline fermentation have been shown to provide an effective alternative carbon source for biological nutrient removal in wastewater treatment plants (WWTPs) that promotes the subsequent release of phosphorus (P) and refractory dissolved organic matter. The dewatering ability of fermented sludge is known to decrease during alkaline fermentation. Here, a novel strategy of initiating fermentation at a pH of 10 was developed to improve VFA purity, P removal efficiency, and fermented sludge dewaterability during WAS fermentation. Although VFAs concentration was lower (1.69 ± 0.09 g COD/L) when the pH was only initially adjusted to pH 10 (R_IA) relative to when the pH was maintained at 10 on a daily basis (R_DC), the purity of VFAs in the fermented liquid was improved (58.48%). Furthermore, the release of total phosphorous (TP) in R_IA was 5.90 times lower than that in R_DC (139.37 mg/L). The normalized capillary suction time and specific resistance to filtration in R_IA decreased to 42.23% and 40.70%, respectively, suggesting that the dewaterability of fermented sludge also improved. The amount of alkali needed was 17.44 kg for each ton of total solid (TS) in R_IA, which was 5.49 times lower than that in R_DC. Thus, approximately 45.44 USD was saved in operational costs for each ton of TS processed in R_IA. These results indicated that VFAs production via initial pH 10 fermentation was a robust and cost-efficient way for providing carbon resources in WWTPs.

Dewatering efficiency of sewage sludge during Fe2+-activated persulfate oxidation: Effect of hydrophobic/hydrophilic properties of sludge EPS

To clarify the effect of the hydrophobic/hydrophilic polarity of extracellular polymeric substances (EPS) on sludge filterability improvement during S₂O₈^2-/Fe²⁺ oxidation, waste activated sludge (WAS), glucose-fed hydrophilic sludge (HPI-WAS), and sodium acetate-fed hydrophobic sludge (HPO-WAS) samples were cultivated, and their dewatering behaviors were individually explored. Experimental results showed that S₂O₈^2- oxidation effectively disintegrated the polymeric EPS and led to a more significant reduction in the water content for HPO-WAS than for HPI-WAS (12.87-15.23% vs 9.31-12.12%), especially regarding the bound water (W_b) content. After oxidation, as high as 38.88-42.61% of the W_b within HPO-WAS samples were declined, much higher than the HPI-WAS samples (19.27-29.20%). Specifically, carbohydrates within sludge EPS negatively influenced the dewatering process of S₂O₈^2-/Fe²⁺ oxidation. By contrast, abundant existence of humic acids and polymeric proteinaceous components (especially those hydrophilic proteins and transitional humic acids) within the sludge EPS exhibited a converse trend. FT-IR and EEM spectral, as well as particle sizes variation for the sludge samples before and after S₂O₈^2-/Fe²⁺ oxidation was also evaluated. This study provides new insight into the enhancement of S₂O₈^2-/Fe²⁺ oxidation for sludge dewatering based on polarity analysis of EPS.

Dewaterability enhancement and sulfide mitigation of CEPT sludge by electrochemical pretreatment

Dewatering and sulfide control are the key challenges in treating chemically enhanced primary treatment (CEPT) sludge. In this study, an electrochemical pretreatment (EPT) approach with the input of 10 V/800 mA was explored for simultaneously improving the dewaterability of CEPT sludge and eliminating its sulfide production. The effects of different electrode materials (carbon and titanium) and EPT durations (from 5 to 15 min) were documented to reveal the underlying EPT mechanism. EPT with titanium electrodes (titanium-EPT) led to limited improvement in dewaterability and sulfide control. EPT with carbon electrodes (carbon-EPT) for 15 min, however, led to decreases in capillary suction time and specific resistance in filtration of over 80% and the suppression of about 99% of hydrogen sulfide (H₂S_(g)) production over 5 days of anaerobic storage. Analysis of the characteristics of treated CEPT sludge revealed that carbon-EPT disintegrated sludge flocs with ∼70% reduction in sludge particle sizes and release of aromatic and tyrosine protein-like substances, thus enhancing sludge dewaterability. The sulfur balance in the liquid and gaseous phases showed that most of the sulfur-containing compounds remained in the solid phase as aliphatic sulfur and sulfonic acid after carbon-EPT, thereby mitigating sulfide emission. While the pattern of sulfur distribution in sludge with titanium-EPT was dominated by sulfide, it was similar to the control sample. Reduction in bacteria associated with sulfide production (i.e., Lachnospiraceae) in CEPT sludge after carbon-EPT also contributed to sulfide elimination. This study demonstrates that EPT can be a superior option for simultaneously enhancing the dewaterability of CEPT sludge and mitigating its sulfide production.

Profiling of amino acids and their interactions with proteinaceous compounds for sewage sludge dewatering by Fenton oxidation treatment

During advanced oxidation treatment for enhancing sludge dewaterability, the peptide chains of protein can be decomposed into amino acids. Protein exhibits a great impact on sewage sludge dewaterability. However, the role of amino acids in sludge dewatering remains unclear. In this study, among the 23 types of amino acids investigated, tryptophane (Trp) and lysine (Lys) were identified as the key amino acids affecting sludge dewaterability during Fenton oxidation treatment. The content of lysine showed positive correlations with capillary suction time (CST), specific resistance to filtration (SRF), and bound water content, and the concentrations of total protein, low molecular weight protein, amines and amides, and 3-turn helix of proteinaceous compounds in bound extracellular polymeric substances (EPS), while the content of tryptophane showed negative correlations with the above parameters. The amino acids may be sourced from damage of the membrane and ribosomal proteins by hydroxyl radicals, and the peptide bonds connected with tryptophane were more inclined to be decomposed than other amino acids. Particularly, more amino acids of tryptophane can result in more hydrophobic interaction, and less necessary energy barrier for aggregation of particles. As such, regulating protein degradation towards production of tryptophane may be related with enhanced sludge dewaterability by Fenton oxidation treatment.

Integrating the (311) facet of MnO2 and the fuctional groups of poly(m-phenylenediamine) in core-shell MnO2@poly(m-phenylenediamine) adsorbent to remove Pb ions from water

Exposed active facets and functional groups are critical for adsorbents obtaining excellent adsorption properties. In the present study, MnO₂@PmPD with exposed active facets was successfully prepared. MnO₂,which came from KMnO₄ by the sacrificial reductant of PmPD, deposited on the surface of PmPD. Meanwhile, we combined experimental study and theoretical calculations to elucidate the distinct adsorption nature of MnO₂@PmPD towards Pb. The surface adsorption of MnO₂@PmPD toward Pb was achieved by the interaction between Pb and O atoms on the surface of MnO₂. The DFT calculations revealed the facet-dependent adsorption of MnO₂ toward Pb. The adsorption affinity of facets toward Pb was in the order of (311) > (111) > (400) > (440), and (311) facet was predominantly adsorption site for Pb. The analysis of partial density of state revealed the strong hybridization between the Pb-p state and O-p states of MnO₂. Additionally, the pores of MnO₂ provide the interstitial channels for the transportation of Pb into PmPD. The Pb entered the internal of MnO₂@PmPD was bonded by the amine and newly formed carboxy groups on PmPD. This study not only develops an efficient adsorbent for heavy metals removing, but also throws light on exemplifying the interaction of Pb with MnO₂ based materials.

Effects of acid, acid-ZVI/PMS, Fe(II)/PMS and ZVI/PMS conditioning on the wastewater activated sludge (WAS) dewaterability and extracellular polymeric substances (EPS)

The effects of four conditioning approaches: Acid, Acid-zero-valent iron (ZVI)/peroxydisulfate (PMS), Fe(II)/PMS and ZVI/PMS, on wastewater activated sludge (WAS) dewatering and organics distribution in supernatant and extracellular polymeric substances (EPS) layers were investigated. The highest reduction in bound water and the most WAS destruction was achieved by Acid-ZVI/PMS, and the optimum conditions were pH 3, ZVI dosage 0.15 g/g dry solid (DS), oxone dosage 0.07 g/g DS and reaction time 10.6 min with the reductions in capillary suction time (CST) and water content (Wc) as 19.67% and 8.49%, respectively. Four conditioning approaches could result in TOC increase in EPS layers and supernatant, and protein (PN) content in tightly bound EPS (TB-EPS). After conditioning, organics in EPS layers could migrate to supernatant. Polysaccharide (PS) was easier to migrate to supernatant than PN. In addition, Acid, Acid-ZVI/PMS or Fe(II)/PMS conditioning promoted the release of some polysaccharides containing ring vibrations v PO, v C-O-C, v C-O-P functional groups from TB-EPS. ESR spectra proved that both radicals of SO₄^-· and ·OH contributed to dewatering and organics transformation and migration. CST value of WAS positively correlated with the ratios of PN/PS in LB-EPS and total EPS, while it negatively correlated with TOC, PN content and PS content in TB-EPS, as well as PS content in supernatant and LB-EPS. BWC negatively correlated to zeta potential and TOC value, PN content, and HA content in supernatant.

Does the combined free nitrous acid and electrochemical pretreatment increase methane productivity by provoking sludge solubilization and hydrolysis?

Free nitrous acid based pretreatments are novel and effective chemical strategies for enhancing waste activated sludge solubilization. In this study, the synergetic effects of the combined free nitrous acid and electrochemical pretreatment on sludge solubilization and subsequent methane productivity were evaluated. The results indicated that pretreatment with 10 V plus 14.17 mg N/L substantially enhanced sludge solubilization, with the highest soluble chemical oxygen demand concentration of 3296.7 mg/L, 25.6-time higher than that without pretreatment (128.9 mg/L). Due to the potential toxicity of NO₂^- and NO₃^- to microorganisms and its bioprocesses, the methane production of sludge pretreated by free nitrous acid was significantly deteriorated. The maximum methane yield (152.0 ± 9.6 mL/g-VS_added) was observed at 10 V pretreatment alone, only 1.7% higher than that of the control (149.4 ± 1.6 mL/g-VS_added). Combined pretreatment indeed enhances the sludge solubilization and hydrolysis, but does not always induce an improved anaerobic digestion efficiency.

Mechanistic insights into heavy metals affinity in magnetic MnO2@Fe3O4/poly(m-phenylenediamine) core-shell adsorbent

Adsorption represents an attractive mean to remediate polluted water. Unfortunately, the surface positive charges, low surface area and complicated separation procedures inhibit the usability of poly (m-phenylenediamine) (PmPD) as an adsorbent for heavy metal removing. To overcome these drawbacks, a magnetic MnO₂@Fe₃O₄/PmPD core-shell adsorbent was designed to remove heavy metals from water. The MnO₂ shell, came from the redox reaction between KMnO₄ and PmPD, increased the surface area and changed the surface electronegativity. MnO₂@Fe₃O₄/PmPD could be easily separated from water. It showed a significant increase in heavy metals removal efficiency, with maximum capacities of 438.6 mg/g for Pb(II) and 121.5 mg/g for Cd(II), respectively. The affinity between heavy metals and MnO₂@Fe₃O₄/PmPD were mainly due to electrostatic attraction, ion exchanges and coordinated interaction. Density functional theory (DFT) calculations further confirmed that Pb and Cd were bonded with O atoms. The calculated adsorption energy indicated that the (111) MnO₂ facet presented stronger adsorption affinity toward Pb(II) than Cd(II). Additionally, FM150 (150 mg) could regenerate 22 L Pb(II) wastewater upon single passage through the filterable column with a flux of 20 mL/min. Thus, the present work demonstrates the promising potential of using MnO₂@Fe₃O₄/PmPD for efficiently removing heavy metals from wastewater.