Exclusive microbially driven autotrophic iron-dependent denitrification in a reactor inoculated with activated sludge

Remediation of arsenic- and nitrate-contaminated groundwater through iron-dependent autotrophic denitrifying culture

Groundwater contamination with arsenic and nitrate poses a pressing concern for the safety of local communities. Bioremediation, utilizing Fe(II)-oxidizing nitrate reducing bacteria, shows promise as a solution to this problem. However, the relatively weak environmental adaptability of a single bacterium hampers practical application. Therefore, this study explored the feasibility and characteristics of a mixed iron-dependent autotrophic denitrifying (IDAD) culture for effectively removing arsenic and nitrate from synthetic groundwater. The IDAD biosystem exhibited stable performace and arsenic resistance, even at a high As(III) concentration of 800 μg/L. Although the nitrogen removal efficiency of the IDAD biosystem decreased from 71.4% to 64.7% in this case, the arsenic concentration in the effluent remained below the standard (10 μg/L) set by WHO. The crystallinity of the lepidocrocite produced by the IDAD culture decreased with increasing arsenic concentration, but the relative abundance of the key iron-oxidizing bacteria norank_f_Gallionellaceae in the culture showed an opposite trend. Metagenomic analysis revealed that the IDAD culture possess arsenic detoxification pathways, including redox, methylation, and efflux of arsenic, which enable it to mitigate the adverse impact of arsenic stress. This study provides theoretical understanding and technical support for the remediation of arsenic and nitrate-contaminated groundwater using the IDAD culture.

New insights and enhancement mechanisms of activated carbon in autotrophic denitrification system utilizing zero-valent iron as indirect electron donors

Zero-valent iron acts as an indirect electron donor, supplying ferrous iron for the nitrate-dependent ferrous oxidation (NDFO) process. The addition of activated carbon (AC) increased the specific NDFO activity in situ and ex situ by 0.4 mg-N/(d·g VSS) and 2.2 mg-N/(d·g VSS), respectively, due to the enrichment of NDFO bacteria. Furthermore, AC reduced the nitrous oxide emission potential of the sludge, a mechanism that metagenomic analysis suggests may act as a cellular energy storage strategy. During a 196-day experiment, a total nitrogen removal efficiency of 53.7 % was achieved, which may be attributed to the upregulation of key genes involved in iron oxidation and denitrification. Based on these findings, a model involving pilin, 'nanowires,' and a cyc2/?→/(FoxE→FoxY)/?→cymA/Complex III/?-mediated pathway for extracellular electron uptake was proposed. Overall, this work provides a feasible strategy for enhancing the nitrogen removal performance of the ZVI-NDFO process.

Microbial enhanced manganese-autotrophic denitrification in reactor: performance, microbial diversity, potential functions

Autotrophic denitrification technology has gained increasing attention in recent years owing to its effectiveness, economical, and environmentally friendly nature. However, the sluggish reaction rate has emerged as the primary impediment to its widespread application. Herein, a bio-enhanced autotrophic denitrification reactor with modified loofah sponge (LS) immobilized microorganisms was established to achieve efficient denitrification. Under autotrophic conditions, a nitrate removal efficiency of 59.55 % (0.642 mg/L/h) and a manganese removal efficiency of 86.48 % were achieved after bio-enhance, which increased by 20.92 % and 36.34 %. The bioreactor achieved optimal performance with denitrification and manganese removal efficiencies of 99.84 % (1.09 mg/L/h) and 91.88 %. ETSA and 3D-EEM analysis reveled manganese promoting electron transfer and metabolic activity of microorganisms. High-throughput sequencing results revealed as the increase of Mn(II) concentration, Cupriavidus became one of the dominant strains in the reactor. Prediction of metabolic functions results proved the great potential for Mn(II)-autotrophic denitrification of LS bioreactor.

Feasibility of simultaneous optimization of Anammox start-up and nitrogen removal performance by intermittent dosing of nanoscale zero-valent iron

The long acclimation period and sensitivity to environmental conditions of Anammox are the bottlenecks for its promotion and application. An innovative strategy was adopted to accelerate functional microbial enhancement and improve nitrogen removal performance by inoculating cryopreserved Anammox sludge and activated sludge with intermittent dosing of nanoscale zero-valent iron (nZVI). The acclimation time was shortened by 76 days with nitrogen removal efficiency (NRE) reaching up to 91.07 %. Anammox, NDFO (nitrate/nitrite-dependent Fe(II) oxidation), Feammox (Fe(III) reduction coupled with anaerobic ammonium oxidation) and abiotic reactions were coupled in the system with nZVI, contributing to 69.79 %, 15.14 %, 9.84 % and 0.25 % of nitrogen removal, respectively. Further microbial analysis demonstrated significant enrichment of functional microorganisms, such as Candidatus Jettenia, Acidovorax and Comamonas. High-efficient nitrogen removal was attribute to the increase of functional genes involved in Anammox, electronic transfer, heme C synthesis and iron metabolism. This work provides an inspiring idea for the mainstream Anammox application.

Composition of the microbial community in surface flow-constructed wetlands for wastewater treatment

Traditionally constructed wetlands face significant limitations in treating tailwater from wastewater treatment plants, especially those associated with sugar mills. However, the advent of novel modified surface flow constructed wetlands offer a promising solution. This study aimed to assess the microbial community composition and compare the efficiencies of contaminant removal across different treatment wetlands: CW1 (Brick rubble, lignite, and Lemna minor L.), CW2 (Brick rubble and lignite), and CW3 (Lemna minor L.). The study also examined the impact of substrate and vegetation on the wetland systems. For a hydraulic retention time of 7 days, CW1 successfully removed more pollutants than CW2 and CW3. CW1 demonstrated removal rates of 72.19% for biochemical oxygen demand (BOD), 74.82% for chemical oxygen demand (COD), 79.62% for NH4 +-N, 77.84% for NO3 --N, 87.73% for ortho phosphorous (OP), 78% for total dissolved solids (TDS), 74.1% for total nitrogen (TN), 81.07% for total phosphorous (TP), and 72.90% for total suspended solids (TSS). Furthermore, high-throughput sequencing analysis of the 16S rRNA gene revealed that CW1 exhibited elevated Chao1, Shannon, and Simpson indices, with values of 1324.46, 8.8172, and 0.9941, respectively. The most common bacterial species in the wetland system were Proteobacteria, Spirochaetota, Bacteroidota, Desulfobacterota, and Chloroflexi. The denitrifying bacterial class Rhodobacteriaceae also had the highest content ratio within the wetland system. These results confirm that CW1 significantly improves the performance of water filtration. Therefore, this research provides valuable insights for wastewater treatment facilities aiming to incorporate surface flow-constructed wetland tailwater enhancement initiatives.

Effect of sand minerals on microbially induced carbonate precipitation by denitrification

Soil improvement techniques utilizing the metabolic functions of microorganisms, including microbially induced carbonate precipitation (MICP), have been extensively researched over the past few decades as part of bio-inspired geotechnical engineering research. Given that metabolic reactions in microorganisms produce carbonate minerals, an enhanced understanding of microbial interaction with soils could improve the effectiveness of MICP as a soil improvement technique. Therefore, this study investigated the effects of sands on MICP by denitrification to employ MICP for geotechnical soil improvement. Under the coexistence of natural sand and artificial silica sand, nitrate-reducing bacteria were cultured in a mixed liquid medium with nitrate, acetate, and calcium ions at 37 °C. Nitrate reduction occurred only in the presence of natural sand. However, the lack of chemical weathering of the composed minerals likely prevented the progress of bacterial growth and nitrate reduction in artificial silica sands. For natural sand, artificial chemical weathering by acid wash and ferrihydrite coating of the sand improved bacterial growth and accelerated nitrate reduction. The calcium carbonate formation induced by denitrification was also influenced by the state of the minerals in the soil and the nitrate reduction rate. The observed MICP enhancement is due to the involvement of coexisting secondary minerals like ferrihydrite with large specific surface areas and surface charges, which may improve the reaction efficiency by serving as adsorbents for bacteria and electron donors and acceptors in the solid phases, thereby promoting the precipitation and crystallization of calcium carbonate on the surfaces. This crystal formation in the minerals provides valuable insights for improving sand solidification via MICP. Considering the interactions between the target soil and microorganisms is essential to improving MICP processes for ground improvement.

Superior nitrate and chromium reduction synergistically driven by multiple electron donors: Performance and the related biochemical mechanism

Nitrate and Cr(VI) are the typical and prevalent co-contaminants in the groundwater, how to synchronously and effectively diminish them has received growing attention. The most problem that currently limits the nitrate and Cr(VI) reduction technology for groundwater remediation is with emphasis on exploring the optimal electron donors. This study investigated the feasibility of utilizing the synergistical effect of inorganic electron donors (pyrite, sulfur) and inherently limited organics to promote synchronous nitrate and Cr(VI) removal, which meets the requirement of naturally low-carbon and eco-friendly technologies. The NO3--N and Cr(VI) removal efficiencies in the pyrite and sulfur involved mixotrophic biofilter (PS-BF: approximately 90.8 ± 0.6% and 99.1 ± 2.1%) were substantially higher than that in a volcanic rock supported biofilter (V-BF: about 49.6% ± 2.8% and 50.0% ± 9.3%), which was consistent with the spatial variations of their concentrations. Abiotic and biotic batch tests directly confirmed the decisive role of pyrite and sulfur for NO3--N and Cr(VI) removal via chemical and microbial pathways. A server decline in sulfate production correlated with decreasing COD consumption revealed that there was sulfur disproportionation induced by limited organics. Metagenomic analysis suggested that chemoautotrophic microbes like Sulfuritalea and Thiobacillus were key players responsible for sulfur oxidation, nitrate and Cr(VI) reduction. The metabolic pathway analysis suggested that genes encoding functional enzymes related to complete denitrification, S oxidation, and dissimilatory sulfate reduction were upregulated, however, genes encoding Cr(VI) reduction enzymes (e.g. chrA, chrR, nemA, and azoR) were downregulated in PS-BF, which further explained the synergistical effect of multiple electron donors. These findings provide insights into their potential cooperative interaction of multiple electron donors on greatly promoting nitrate and Cr(VI) removal and have implications for the remediation technology of nitrate and Cr(VI) co-contaminated groundwater.

Interspecies electron transfer and microbial interactions in a novel Fe(II)-mediated anammox coupled mixotrophic denitrification system

This study effectively coupled anammox and mixotrophic denitrification at a high nitrogen load rate of 6.84 g N/L/d with 40 mg/L Fe(II). Fe(II) enhanced the activity of nitrate reductase, nitrite reductase, and hydrazine dehydrogenase enzymes, facilitating accelerated ATP synthesis. Through electrochemical experiments, interspecies electron transfer processes in coupled system were explored. Fe(II) promoted flavin mononucleotide secretion, enhancing electron-donating and electron-accepting capacity by 2.8 and 1.3 times, respectively. Fe(II) triggered the enrichment of autotrophic denitrifying bacteria (Azospira and Hydrogenophaga), transitioning from single organic nutrient to mixotrophic denitrification. Meanwhile, Fe(II) increased Candidatus_Kuenenia abundance from 35.2 % to 49.0 %, establishing the competitive advantage of anammox bacteria over completed denitrifying bacteria (Comamonas). The synergistic interactions between anammox and various denitrification pathways achieved a nitrogen removal rate of 5.88 g N/L/d, with anammox contribution rate of 88.3 %. This study provides insights into broadening the application of partial denitrification /anammox and electron transfer in multi-bacterial coupling systems.

Advancing the treatment of low carbon-to-nitrogen ratio municipal wastewater using a novel microaerobic sludge bed approach: Insights into enhanced performance and functional microbial community

Microaerobic sludge bed systems could align with low-energy, reasonable carbon-nitrogen (C/N) ratio, and synchronous removal objectives during wastewater treatment. However, its ability to treat municipal wastewater (MW) with varying low C/N ratio, low NH4+ concentration, along with managing sludge bulking and loss are still unclear. Against this backdrop, this study investigated the performance of an Upflow Microaerobic Sludge Bed Reactor (UMSR) treating MW characterized by varying low C/N ratios and low NH4+ concentrations. The study also thoroughly examined associated sludge bulking and loss, pollutant removal efficiencies, sludge settleability, microbial community structures, functional gene variations, and metabolic pathways. Findings revealed that the effluent NH4+-N concentration gradually decreased to 0 mg/L with a decrease in the C/N ratio, whereas the effluent COD was unaffected by the influent, maintaining a concentration below 50 mg/L. Notably, TN removal efficiency reached 90% when C/N ratio was 3. The decrease in the C/N ratio (C/N ratio was 1) increased microbial community diversity, with abundances of AOB, AnAOB, aerobic denitrifying bacteria, and anaerobic digestion bacteria reaching 8.34%, 0.96%, 5.07%, and 9.01%, respectively. Microorganisms' metabolic pathways significantly shifted, showing increased carbohydrate and cofactor/vitamin metabolism and decreased amino acid metabolism and xenobiotic biodegradation. This study not only provides a solution for the effluent of different pre-capture carbon processes but also demonstrates the UMSR's capability in managing low C/N ratio municipal wastewater and emphasizes the critical role of microbial community adjustments and functional gene variations in enhancing nitrogen removal efficiency.

In situ electron generation through Fe/C supported sludge coupled with a counter-diffusion biofilm for electron-deficient wastewater treatment: Binding properties and catalytic competition mechanism of nitrate reductase

A membrane-aerated biofilm-coupled Fe/C supported sludge system (MABR-Fe/C) was constructed to achieve in situ electron production for NO3--N reduction enhancement in different Fe/C loadings (10 g and 200 g). The anoxic environment formed in the MABR-Fe/C promoted a continual Fe2+release of Fe/C in 120 d operation (average Fe2+concentrations is 1.18 and 2.95 mg/L in MABR-Fe/C10 and MABR-Fe/C200, respectively). Metagenomics results suggested that the electrons generated from ongoing Fe2+ oxidation were transferred via the Quinone pool to EC 1.7.5.1 rather than EC 1.9.6.1 to complete the process of NO3--N reduction to NO2--N in Acidovorax, Ottowia, and Polaromonas. In the absence of organic matter, the NO3--N removal in MABR-Fe/C10 and MABR-Fe/C200 increased by 11.99 and 12.52 mg/L, respectively, compared to that in MABR. In the further NO2--N reduction, even if the minimum binding free energy (MBFE) was low, NO2--N in Acidovorax and Dechloromonas preferentially bind the Gln-residues for dissimilatory nitrate reduction (DNR) in the presence of Fe/C. Increasing Fe/C loading (MABR-Fe/C200) caused the formation of different residue binding sites, further enhancing the already dominant DNR. When DNR in MABR-Fe/C200 intensified, the TN in the effluent increased by 3.75 mg/L although the effluent NO3--N concentration was lower than that in MABR-Fe/C10. This study demonstrated a new MABR-Fe/C system for in situ electron generation to enhance biological nitrogen removal and analyzed the NO3--N reduction pathway and metabolic mechanism, thus providing new ideas for nitrogen removal in electron-deficient wastewater.

Significantly Enhanced Nitrate and Phosphorus Removal by Pyrite/Sawdust Composite-Driven Mixotrophic Denitrification with Boosted Electron Transfer: Comprehensive Evaluation of Water-Gas-Biofilm Phases during a Long-Term Study

Further reducing total nitrogen (TN) and total phosphorus (TP) in the secondary effluent needs to be realized effectively and in an eco-friendly manner. Herein, four pyrite/sawdust composite-based biofilters were established to treat simulated secondary effluent for 304 days. The results demonstrated that effluent TN and TP concentrations from biofilters under the optimal hydraulic retention time (HRT) of 3.5 h were stable at <2.0 and 0.1 mg/L, respectively, and no significant differences were observed between inoculated sludge sources. The pyrite/sawdust composite-based biofilters had low N2O, CH4, and CO2 emissions, and the effluent's DOM was mainly composed of five fluorescence components. Moreover, mixotrophic denitrifiers (Thiothrix) and sulfate-reducing bacteria (Desulfosporosinus) contributing to microbial nitrogen and sulfur cycles were enriched in the biofilm. Co-occurrence network analysis deciphered that Chlorobaculum and Desulfobacterales were key genera, which formed an obvious sulfur cycle process that strengthened the denitrification capacity. The higher abundances of genes encoding extracellular electron transport (EET) chains/mediators revealed that pyrite not only functioned as an electron conduit to stimulate direct interspecies electron transfer by flagella but also facilitated EET-associated enzymes for denitrification. This study comprehensively evaluates the water-gas-biofilm phases of pyrite/sawdust composite-based biofilters during a long-term study, providing an in-depth understanding of boosted electron transfer in pyrite-based mixotrophic denitrification systems.

Optimization of operating parameters and microbiological mechanism of a low C/N wastewater treatment system dominated by iron-dependent autotrophic denitrification

Ferrous iron (Fe2+) reduces the amount of external carbon source used for the denitrification of low-C/N wastewater. The effects of key operating parameters on the efficiency of ferrous-dependent autotrophic denitrification (FDAD) and the functioning mechanism of the microbiome can provide a regulatory strategy for improving the denitrification efficiency of low C/N wastewater. In this study, the response surface method (RSM) was used to explore the influence of four important parameters-the molar ratio of Fe2+ to NO3--N (Fe/N), total organic carbon (TOC), the molar ratio of inorganic carbon to NO3--N (IC/N) and sludge volume (SV, %)-on the FDAD efficiency. Functional prediction and molecular ecological networks based on high-throughputs sequencing techniques were used to explore changes in the structure, function, and biomarkers of the sludge microbial community. The results showed that Fe/N and TOC were the main parameters affecting FDAD efficiency. Higher concentrations of TOC and high Fe/N ratios provided more electron donors and improved denitrification efficiency, but weakened the importance of biomarkers (Rhodanobacter, Thermomonas, Comamonas, Thauera, Geothrix and unclassified genus of family Gallionellaceae) in the sludge ecological network. When Fe/N > 4, the denitrification efficiency fluctuated significantly. Functional prediction results indicated that genes that dominated N2O and NO reduction and the genes that dominated Fe2+ transport showed a slight decrease in abundance at high Fe/N levels. In light of these findings, we recommend the following optimization ranges of parameters: Fe/N (3.5-4); TOC/N (0.36-0.42); IC/N (3.5-4); and SV (approximately 35%).

In situ incubation of iron(II)-bearing minerals and Fe(0) reveals insights into metabolic flexibility of chemolithotrophic bacteria in a nitrate polluted karst aquifer

Groundwater nitrate pollution is a major reason for deteriorating water quality and threatens human and animal health. Yet, mitigating groundwater contamination naturally is often complicated since most aquifers are limited in bioavailable carbon. Since metabolically flexible microbes might have advantages for survival, this study presents a detailed description and first results on our modification of the BacTrap© method, aiming to determine the prevailing microbial community's potential to utilize chemolithotrophic pathways. Our microbial trapping devices (MTDs) were amended with four different iron sources and incubated in seven groundwater monitoring wells for ∼3 months to promote growth of nitrate-reducing Fe(II)-oxidizing bacteria (NRFeOxB) in a nitrate-contaminated karst aquifer. Phylogenetic analysis based on 16S rRNA gene sequences implies that the identity of the iron source influenced the microbial community's composition. In addition, high throughput amplicon sequencing revealed increased relative 16S rRNA gene abundances of OTUs affiliated to genera such as Thiobacillus, Rhodobacter, Pseudomonas, Albidiferax, and Sideroxydans. MTD-derived enrichments set up with Fe(II)/nitrate/acetate to isolate potential NRFeOxB, were dominated by e.g., Acidovorax spp., Paracoccus spp. and Propionivibrio spp. MTDs are a cost-effective approach for investigating microorganisms in groundwater and our data not only solidifies the MTD's capacity to provide insights into the metabolic flexibility of the aquifer's microbial community, but also substantiates its metabolic potential for anaerobic Fe(II) oxidation.

Synchronous in-situ sludge reduction and enhanced denitrification through improving electron transfer during endogenous metabolisms with Fe(Ⅱ) addition

The creation of large amounts of excess sludge and residual nitrogen are critical issues in wastewater biotreatment. This study introduced Fe(II) into an oligotrophic anaerobic reactor (OARFe) that was implemented to modify an anoxic-oxic process to motivate in-situ sludge reduction and enhance denitrification under an effective electron shuttle among organic matter, nitrogen, and Fe. The addition of 15 mg L-1 Fe(II) resulted in a sludge reduction efficiency reached 32.0% with a decreased effluent nitrate concentration of 33.3%. This was mostly attributed to the electron transfer from Fe(II) to organic matters and nitrogen species in OARFe. The participation of Fe(II) led to the upregulation of Geothrix and Terrimonas, which caused active organic matter hydrolysis and cell lysis to stimulate the release of extracellular polymeric substances (EPS) and substance transfer between each layer of EPS. The higher utilization of released bioavailable dissolved organic matter improved endogenous denitrification, which can be combined with iron autotrophic denitrification to realize multiple electron donor-based nitrogen removal pathways, resulting in an increased nitrate removal rate of 58.2% in the absence of external carbon sources. These functional bacteria associated with the transformation of nitrogen and carbon and cycling between ferrous and ferric ions were enriched in OARFe, which contributed to efficient electron transport occurred both inside and outside the cell and increased 2,3,5-triphenyltetrazolium chloride electronic transport system activity by 46.9%. This contributed to the potential operational costs of chemical addition and sludge disposal of Fe-AO being 1.9 times lower than those of conventional A2O processes. These results imply that the addition of ferrous ions to an oligotrophic anaerobic zone for wastewater treatment has the potential for low-cost pollution control.

Temperature-resilient superior performances by coupling partial nitritation/anammox and iron-based denitrification with granular formation

Partial nitritation-anammox (PN/A), an energy-neutral process, is widely employed in the treatment of nitrogen-rich wastewater. However, the intrinsic nitrate accumulation limits the total nitrogen (TN) removal, and the practical application of PN/A continues to face a significant challenge at low temperatures (<15 °C). Here, an integrated partial nitritation-anammox and iron-based denitrification (PNAID) system was developed to address the concern. Two up-flow bioreactors were set up and operated for 400 days, with one as the control group and the other as the experiment group with the addition of Fe0. In comparison to the control group, the experiment group with the Fe0 supplement showed better nitrogen removal during the entire course of the experiment at different temperature levels. Specifically, the TN removal efficiency of the control group decreased from 82.9 % to 53.9 % when the temperature decreased from 30 to 12 °C, while in stark contrast, the experiment group consistently achieved 80 % of TN removal in the same condition. Apart from the enhanced nitrogen removal, the experiment group also exhibited better phosphorus removal (10.6 % versus 74.1 %) and organics removal (49.5 % versus 65.1 %). The enhanced and resilient nutrient removal performance of the proposed integrated process under low temperatures appeared to be attributed to the compact structure of granules and the increased microbial metabolism with Fe0 supplement, elucidated by a comprehensive analysis including microbial-specific activity, apparent activation energy, characteristics of granular sludge, and metagenomic sequencing. These results clearly confirmed that Fe0 supplement not only improved nitrogen removal of PN/A process, but also conferred a certain degree of robustness to the system in the face of temperature fluctuations.

Iron-electrolysis assisted anammox/denitrification system for intensified nitrate removal and phosphorus recovery in low-strength wastewater treatment

Two iron-electrolysis assisted anammox/denitrification (EAD) systems, including the suspended sludge reactor (ESR) and biofilm reactor (EMR) were constructed for mainstream wastewater treatment, achieving 84.51±4.38 % and 87.23±3.31 % of TN removal efficiencies, respectively. Sludge extracellular polymeric substances (EPS) analysis, cell apoptosis detection and microbial analysis demonstrated that the strengthened cell lysate/apoptosis and EPS production acted as supplemental carbon sources to provide new ecological niches for heterotrophic bacteria. Therefore, NO3--N accumulated intrinsically during anammox reaction was reduced. The rising cell lysis and apoptosis in the ESR induced the decline of anammox and enzyme activities. In contrast, this inhibition was scavenged in EMR because of the more favorable environment and the significant increase in EPS. Moreover, ESR and EMR achieved efficient phosphorus removal (96.98±5.24 % and 96.98±4.35 %) due to the continued release of Fe2+ by the in-situ corrosion of iron anodes. The X-ray diffraction (XRD) indicated that vivianite was the dominant P recovery product in EAD systems. The anaerobic microenvironment and the abundant EPS in the biofilm system showed essential benefits in the mineralization of vivianite.

Two-stage sequencing batch reactors with added iron shavings for nutrient removal and aerobic sludge granulation treating real wastewater with low carbon to nitrogen ratios

In response to the challenges of limited nutrient removal and the difficulty in forming aerobic granular sludge (AGS) with low carbon to nitrogen (C/N) ratios, a novel two-stage sequencing batch reactors (SBRs) (R1 and R2) system with added iron shavings was proposed and established. The results showed that AGS was developed and nitrogen (82.8 %) and phosphorus (94.7 %) were effectively removed under a C/N ratio at 1.7 ± 0.5. The average size of R1 and R2 increased from 45.3 μm to 138.7 μm and 132.8 μm. Under high biological selective pressure, phosphorus accumulating organisms like Comamonadaceae (14.8 %) and Chitinophagales (5.7 %) experienced enrichment in R1. Furthermore, R2 exhibited an increased abundance of nitrifying bacteria (2.3 %) and a higher proportion of nitrogen removal through autotrophic denitrification (＞17.5 %). Overall, this study introduces an innovative two-stage SBRs with added iron shavings, offering a novel approach for the treatment of low C/N ratios wastewater.

Insights into nitrate-reducing Fe(II) oxidation by Diaphorobacter caeni LI3T through kinetic, nitrogen isotope fractionation, and genome analyses

Nitrate (NO3-)-reducing Fe(II) oxidation (NRFO) is prevalent in anoxic environments. However, it is uncertain in which step(s) the biological Fe(II) oxidation is coupled with denitrification during NRFO. In this study, a heterotrophic NRFO bacterium, Diaphorobacter caeni LI3T, was isolated from paddy soil and used to investigate the transformation of Fe(II) and nitrogen as well as nitrogen isotopic fractionation (δ15N-N2O) during NRFO. Fe(II) oxidation was observed in the Cell+NO3- +Fe(II), Cell+NO2- + Fe(II), and NO2- + Fe(II) treatments, resulting in precipitation of amorphous Fe(III) minerals and lepidocrocite on the surface and in the periplasm of cells. The presence of Fe(II) slightly accelerated microbial NO3- reduction in the Cell+NO3- + Fe(II) treatment relative to the Cell+NO3- treatment, but slowed down the NO2- reduction in the Cell+NO2- + Fe(II) treatment relative to the Cell+NO2- treatment likely due to cell encrustation that blocking microbial NO2- reduction in the periplasm. The δ15N-N2O results in the Cell+NO3- + Fe(II) treatment were close to those in the Cell+NO3- and Cell+NO2- treatments, indicating that the accumulative N2O is primarily of biological origin during NRFO. The genome analysis found a complete set of denitrification and oxidative phosphorylation genes in strain LI3T, the metabolic pathways of which were closely related with cyc2 and cytc as indicated by protein-protein interactions network analysis. It is proposed that Fe(II) oxidation is catalyzed by the outer membrane protein Cyc2, with the resulting electrons being transferred to the nitrite reductase NirS via CytC in the periplasm, and the CytC can also accept electrons from the oxidative phosphorylation in the cytoplasmic membrane. Overall, our findings provide new insights into the potential pathways of biological Fe(II) oxidation coupled with nitrate reduction in heterotrophic NRFO bacteria.

Iron cycle-enhanced anaerobic ammonium oxidation in microaerobic granular sludge

Granule-based partial nitritation and anaerobic ammonium oxidation (PN/A) is an energy-efficient approach for treating ammonia wastewater. When treating low-strength ammonia wastewater, the stable synergy between PN and anammox is however difficult to establish due to unstable dissolved oxygen control. Here, we proposed, the PN/A granular sludge formed by a micro-oxygen-driven iron redox cycle with continuous aeration (0.42 ± 0.10 mg-O2/L) as a novel strategy to achieve stable and efficient nitrogen (N) removal. 240-day bioreactor operation showed that the iron-involved reactor had 37 % higher N removal efficiency than the iron-free reactor. Due to the formation of the microaerobic granular sludge (MGS), the bio(chemistry)-driven iron cycle could be formed with the support of anaerobic ammonium oxidation coupled to Fe3+ reduction. Both ammonia-oxidizing bacteria and generated Fe2+ could scavenge the oxygen as a defensive shield for oxygen-sensitive anammox bacteria in the MGS. Moreover, the iron minerals derived from iron oxidation and Fe-P precipitates were also deposited on the MGS surface and/or embedded in the internal channels, thus reducing the size of the channels that could limit oxygen mass transfer inside the MGS. The spatiotemporal assembly of diverse functional microorganisms in the MGS for the realization of stable PN/A could be achieved with the support of the iron redox cycle. In contrast, the iron-free MGS could not optimize oxygen mass transfer, which led to an unstable and inefficient PN/A. This work provides an alternative iron-related autotrophic N removal for low-strength ammonia wastewater.

Effect mechanism of micron-scale zero-valent iron enhanced pyrite-driven denitrification biofilter for nitrogen and phosphorus removal

This study aims to explore the effect mechanism of micron-scale zero-valent iron (mZVI) to improve nitrogen and phosphorus removal in a pyrite (FeS2)-driven denitrification biofilter (DNBF) for the secondary effluent treatment. Two similar DNBFs (DNBF-A with FeS2 as fillers and DNBF-B with the mixture mZVI and FeS2 as carrier) were developed. The results showed that NO3--N, total nitrogen (TN) and PO43--P removal efficiencies were up to 91.64%, 67.44% and 80.26% in DNBF-B, which were obviously higher than those of DNBF-A (with NO3--N, TN and PO43--P removal efficiencies of 38.39%, 44.89% and 53.02%, respectively). Kinetic analysis of both PO43--P and NO3--N showed an increase in the rate constant (K) for DNBF-B compared to DNBF-A. The addition of mZVI not only improved the electron transport system activity (ETSA), but also achieved system Fe(II)/Fe(III) redox cycle in DNBF-B. In addition, the high-throughput sequencing analysis indicated that the addition of mZVI could obviously stimulate the enrichment of functional bacteria, such as Thiobacillus (11.99%), Mesotoga (7.50%), JGI-0000079D21 (6.37%), norank_f__Bacteroidetes_vadinHA17 (6.19%), Aquimonas (5.93%) and Arenimonas (3.97%). These genus played the important role in nitrogen and phosphorus removal in DNBF-B. Addition mZVI in the FeS2-driven denitrification biofilter is highly promising for TN and TP removal during secondary effluent treatment.

Fe(0)-Dissimilatory Nitrate Reduction to Ammonium for Autotrophic Recovery of Reactive Nitrogen

Bioreduction of nitrate to value-added ammonium is a potentially sustainable strategy to recycle nutrients from wastewater. Here, we have proven the feasibility of the reduction of autotrophic nitrate to ammonium with electrons extracted from Fe(0). Using a Geobacter-dominated anodic biofilm as an inoculum, we achieved nitrate-to-ammonium efficiency up to 90 ± 3% with a nitrate reduction rate of 35 ± 1.3 mg N/d/L. An electron acceptor instead of an inoculum greatly influenced the Fe(0)-dissimilatory nitrate reduction to ammonium (DNRA), where nitrite as the electron acceptor provided an effective selective pressure to enrich Geobacter from initial 5 to 56%. The DNRA repressing denitrification was demonstrated by the reverse tendencies of upregulated nrfA and downregulated nirS gene transcription. This finding provides a new route for autotrophic nitrate removal and recycling from water, which has a broader implication on biogeochemical nitrogen and iron cycling.

The biochar/Fe-modified biocarrier driven simultaneous NDFO and Feammox to remove nitrogen from eutrophic water

Novelty techniques of Fe(III) reduction coupled to anaerobic ammonium oxidation (i.e. Feammox) and nitrate-dependent Fe(II) oxidation (i.e. NDFO) provide new insights into autotrophic nitrogen removal from eutrophic waters. Given that Feammox and NDFO can theoretically complete the simultaneous NH+ 4-N and NO- 3-N removal via Fe(III)/Fe(II) cycle, this study introduces iron powder to the surface of the biocarrier as a solid-phase source of Fe, and biochar was used as an electron shuttle to mix with the iron powder to improve the bioavailability of iron. Batch experiments was carried out for 70 days using simulated eutrophic water as the medium to investigate the effects of the modified biocarrier for enhanced nitrogen removal. The results showed that BC1 (Fe:BC=1:1) with the highest relative Fe content exhibited the highest nitrogen removal efficiency of 66.74%. XPS and XRD results showed both Fe(III) and Fe(II) compounds on the biocarrier surface, confirming the occurrence of Fe(III)/Fe(II) cycle. The ex-situ activity test indicated that functional activity was positively correlated with the iron content of the biocarrier. The in-situ experiments with different substrates showed the occurrence of Feammox and NDFO. NDFO bacteria (Gallionellaceae), Feammox bacteria (Alicycliphilus), denitrifying and digesting bacteria were enriched, suggesting that the coupled nitrogen removal of NDFO and Feammox is the result of cooperation between different functional microorganisms. Thus, the Fe-modified biocarrier showed superior performance and application potential in catalyzing autotrophic nitrogen removal from eutrophic water by functional microorganisms.

Removal of oxytetracycline from wastewater by biochar modified with biosynthesized iron oxide nanoparticles and carbon nanotubes: Modification performance and adsorption mechanism

The pollution problem of oxytetracycline (OTC) from wastewater becomes more serious, so an efficient, economical, and green adsorption material is urgently explored. In this study, the multilayer porous biochar (OBC) was prepared by coupling carbon nanotubes with iron oxide nanoparticles synthesized by Aquabacterium sp. XL4 to modify corncobs under medium temperature (600 °C) conditions. The adsorption capacity of OBC could reach 72.59 mg g-1 after preparation and operation parameters were optimized. In addition, various adsorption models suggested that OTC removal resulted from the combined effect of chemisorption, multilayer interaction, and disordered diffusion. Meanwhile, the OBC was fully characterized and exhibited a large specific surface area (237.51 m2 g-1), abundant functional groups, stable crystal structure, high graphitization, and mild magnetic properties (0.8 emu g-1). The OTC removal mechanisms mainly included electrostatic interactions, ligand exchange, π-π bonding reactions, hydrogen bonds, and complexation. pH and coexistence substance experiments revealed that the OBC possesses a wide pH adaptation range and excellent anti-interference ability. Finally, the safety and reusability of OBC were confirmed by repeated experiments. In summary, OBC as a biosynthetic material shows considerable potential for application in the field of purifying new pollution from wastewater.

Performance, microbial growth and community interactions of iron-dependent denitrification in freshwaters

Iron-dependent denitrification is a safe and promising technology for nitrogen removal in freshwaters. However, the understanding of microbial physiology and interactions during the process was limited. Denitrifying systems inoculated with freshwater samples were operated with and without iron(II) at a low C/N ratio for 54 days. Iron addition improved nitrogen removal. Batch experiments confirmed that microbially mediated reaction rather than abiotic reaction dominated during the process. Metagenomics recovered genomes of the five most abundant microorganisms, which accounted for over 99% of the community in every triplicate of the iron-based system. Based on codon usage bias, all of them were fast-growing organisms. The total abundance of fast-growing organisms was 38% higher in the system with iron than in the system without iron. Notably, the most abundant organism Diaphorobacter did not have enzymes for asparagine and aspartate biosynthesis, whereas Rhodanobacter could not produce serine and cobalamin. Algoriphagus and Areminomonas lost synthesis enzymes for more amino acids and vitamins. However, they could always obtain these growth-required substances from another microorganism in the community. The two-partner relationship minimized the limitation on microbial reproduction and increased community stability. Our results indicated that iron addition improved nitrogen removal by supplying electron donors, promoting microbial growth, and building up syntrophic interactions among microorganisms with timely communications. The findings provided new insights into the process, with implications for freshwater remediation.

Filtration columns containing waste iron shavings, loofah, and plastic shavings for further removal of nitrate and phosphate from wastewater effluent

A novel pilot-scale advanced treatment system combining waste products as fillers is proposed and established to enhance the removal of nitrate (NO₃^--N) and phosphate (PO₄^3--P) from secondary treated effluent. The system consists of four modular filter columns, one containing iron shavings (R1), two containing loofahs (R2 and R3), and one containing plastic shavings (R4). The monthly average concentration of total nitrogen (TN) and total phosphorus (TP) decreased from 8.87 to 2.52 mg/L and 0.607 to 0.299 mg/L, respectively. Micro-electrolysis of iron shavings produces Fe²⁺ and Fe³⁺ to remove PO₄^3--P, while oxygen (O₂) consumption creates anoxic conditions for subsequent denitrification. Gallionellaceae, iron-autotrophic Microorganisms, enriched the surface of iron shavings. The loofah served as a carbon source to remove NO₃^--N, and its porous mesh structure facilitated the attachment of biofilm. The plastic shavings intercepted suspended solids and degraded excess carbon sources. This system can be scaled up and installed at wastewater plants to improve the water quality of effluent cost-effectively.

Sustained-release nitrate combined with microbial fuel cell: A novel strategy for PAHs and odor removal from sediment

Nitrate addition is a biostimulation technique that can improve both the oxidation of acid volatile sulfide (AVS) through autotrophic denitrification and the biodegradation of polycyclic aromatic hydrocarbons (PAHs) via heterotrophic denitrification. However, during the remediation, parts of the dissolved nitrate in the sediment migrates from the sediment to the overlying water, leading to the loss of effective electron acceptor. To overcome this limitation, a combined approached was proposed, which involved nitrocellulose addition and a microbial fuel cell (MFC). Results indicated the nitrate could be slowly released and maintained at a higher concentration over long term. In the combined system, the removal efficiencies of PAHs and AVS were 71.56% and 89.76%, respectively. Furthermore, the voltage attained for the MFC-nitrocellulose treatment was maintained at 146.1 mV on Day 70, which was 5.37 times higher than that of the MFC-calcium nitrate treatment. Sediments with nitrocellulose resulted in lower levels of nitrate and ammonium in the overlying water. Metagenomic results revealed that the combined technology improved the expression of nitrogen-cycling genes. The introduction of MFC inhibited sulfide regeneration during incubation by suppressing the enzyme activity like EC4.4.1.2. The enhanced biostimulation provided potential for in-situ bioremediation utilizing MFC coupled with slow-released nitrate (i.e., nitrocellulose) treatment.

Microbial mixotrophic denitrification using iron(II) as an assisted electron donor

Mixotrophic denitrification processes have a great potential in nitrogen removal in biological wastewater treatment processes. However, so far, few studies have focused on the mixotrophic denitrification system using Fe(II) as an exclusively assisted electron donors and the underlying mechanisms in such a process remain unclear. Furthermore, the mechanisms by which microorganisms cover carbon, nitrogen, phosphorus and iron in an iron-assisted mixotrophic system remain unrevealed. In this work, we explore the feasibility of using Fe(II) as an assisted electron donor for enhancing simultaneous nitrogen and phosphorus removal via long-term reactor operation and batch tests. The results show that Fe(II) could provide electrons for efficient nitrate reduction and that biological reactions played a predominant role in these systems. In these systems Thermomonas, a strain of nitrate-reduction Fe(II)-oxidation bacterium, was enriched and accounted for a maximum abundance of 60.2%. These findings indicate a great potential of the Fe(II)-assisted mixotrophic denitrification system for practical use as an efficient simultaneous nitrogen and phosphorus removal process.

Autotrophic denitrification using Fe(II) as an electron donor: A novel prospective denitrification process

As a newly identified nitrogen loss pathway, the nitrate-dependent ferrous oxidation (NDFO) process is emerging as a research hotspot in the field of low carbon to nitrogen ratio (C/N) wastewater treatment. This review article provides an overview of the NDFO process and summarizes the functional microorganisms associated with NDFO from different perspectives. The potential mechanisms by which external factors such as influent pH, influent Fe(II)/N (mol), organic carbon, and chelating agents affect NDFO performance are also thoroughly discussed. As the electron-transfer mechanism of the NDFO process is still largely unknown, the extensive chemical Fe(II)-oxidizing nitrite-reducing pathway (NDFO_chem) of the NDFO process is described here, and the potential enzymatic electron transfer mechanisms involved are summarized. On this basis, a three-stage electron transfer pathway applicable to low C/N wastewater is proposed. Furthermore, the impact of Fe(III) mineral products on the NDFO process is revisited, and existing crusting prevention strategies are summarized. Finally, future challenges facing the NDFO process and new research directions are discussed, with the aim of further promoting the development and application of the NDFO process in the field of nitrogen removal.

Enhanced nitrate and cadmium removal performance at low carbon to nitrogen ratio through immobilized redox mediator granules and functional strains in a bioreactor

The coexistence of multiple pollutants and lack of carbon sources are challenges for the biological treatment of wastewater. To achieve simultaneous removal of nitrate (NO₃^--N) and cadmium (Cd²⁺) at low carbon to nitrogen (C/N) ratios, 2-hydroxy-1,4-naphthoquinone (HNQ) was selected from three redox mediators as an accelerator for denitrification of heterotrophic strain Pseudomonas stutzeri sp. GF2 and autotrophic strain Zoogloea sp. FY6. Then, halloysite nanotubes immobilized with 2-hydroxy-1,4-naphthoquinone (HNTs-HNQ) were prepared and a bioreactor was constructed with immobilized redox mediator granules (IRMG) as the carrier, which was immobilized with HNTs-HNQ and inoculated with the two strains. The immobilized HNQ and the inoculated strains jointly improved the removal ability of NO₃^--N and Cd²⁺ and the removal efficiency of NO₃^--N (25.0 mg L^-1) and Cd²⁺ (5.0 mg L^-1) were 92.81% and 93.94% at C/N = 1.5 and hydraulic retention time (HRT) = 4 h. The Cd²⁺ was removed by adsorption of iron oxides (FeO(OH) and Fe₃O₄) and IRMG. The electron transport system activity (ETSA) of bacteria was improved and the composition of dissolved organic matter in the effluent was not affected by HNQ. The HNQ promoted the production of FeO(OH) and up-regulated the proportion of Zoogloea (54.75% in the microbial community), indicating that Zoogloea sp. FY6 was dominant in the microbial community. In addition, HNQ influenced the metabolic pathways and improved the relative abundance of some genes involved in nitrogen metabolism and the iron redox cycle.

A novel approach to estimate and control denitrification performance in activated sludge systems with respirogram technology

Respirogram technology has been widely applied for aerobic process, however, the response of respirogram to anoxic denitrification is still unclear. To reveal such response may help to design a new method for the evaluation of the performance of denitrification. The size distribution of flocs measured at different denitrification moments demonstrated a clear expansion of flocs triggered by denitrification, during which higher specific endogenous and quasi-endogenous respiration rates (SOUR_e and SOUR_q) were also observed. Furthermore, SOUR_q increases exponentially with the specific denitrification rate (SDNR), suggesting that there should be a maximum SDNR in conventional activated sludge systems. Based on these findings, an index R_q/t, defined as the ratio of quasi-endogenous (OUR_q) to maximum respiration rate (OUR_t), is proposed to estimate the denitrification capacity that higher R_q/t indicates higher denitrification potential, which can be readily obtained without complex measurement or analysis, and it offers a novel and promising respirogram-based approach for denitrification estimation and control by taking measures to extend anoxic time to maintain its value at a high level within a certain range.

New insights on simultaneous nitrate and phosphorus removal in pyrite-involved mixotrophic denitrification biofilter for a long-term operation: Performance change and its underlying mechanism

Simultaneous nitrate and phosphorus removal can be completed by pyrite- and influent organics-involved mixotrophic denitrification and chemical phosphorus removal via iron precipitation. However, so far, how their removal performances change with iron precipitation accumulation remains unclear. In this study, the differences in nitrate and phosphorus removal from municipal tailwater between volcanic and pyrite supported biofilters (V-BF, P-BF) for a long-term operation were investigated, as well as the underlying mechanism for these differences. The nitrate removal efficiencies (NREs) in P-BF were greater than those in V-BF due to the synergistic effect of influent organic and pyrite, as evidenced by comparable TOC consumption and Fe²⁺/SO₄^2- production. The NREs in P-BF were gradually lower than in V-BF as a result of bacterial cell-iron encrustation observed in TEM images, which would deteriorate microbial activity. However, the phosphorus removal efficiencies (PREs) in P-BF remained consistently higher than in V-BF, resulting from chemical phosphorus removal which was confirmed that P, Fe and O elements dominated on the pyrite surface after use by SEM-EDS. The dominant denitrifying bacteria differed significantly, autotrophic and heterotrophic denitrifying microorganisms coexisted in P-BF. The relative abundances of the narG coding gene in P-BF were higher than that in V-BF, which was consistent with the total relative abundances of identified denitrifying bacteria. Besides, the mechanism of simultaneous nitrogen and phosphorus removal in the pyrite-involved mixotrophic denitrification process has been deduced. This work has significant implications for the practical application of a pyrite-involved mixotrophic denitrification process for low C/N wastewater treatment.

Perspective on inorganic electron donor-mediated biological denitrification process for low C/N wastewaters

Nitrate is the most common water environmental pollutant in the world. Inorganic electron donor-mediated denitrification is a typical process with significant advantages in treating low carbon-nitrogen ratio water and wastewater and has attracted extensive research attention. This review summarizes the denitrification processes using inorganic substances, including hydrogen, reductive sulfur compounds, zero-valent iron, and iron oxides, ammonium nitrogen, and other reductive heavy metal ions as electron donors. Aspects on the functional microorganisms, critical metabolic pathways, limiting factors and mathematical modeling are outlined. Also, the typical inorganic electron donor-mediated denitrification processes and their mechanism, the available microorganisms, process enhancing approaches and the engineering potentials, are compared and discussed. Finally, the prospects of developing the next generation inorganic electron donor-mediated denitrification process is put forward.

Fe(Ⅱ) improving sulfurized Anammox coupled with autotrophic denitrification performance: Based on interspecies and intracellular electron transfer

Insufficient nitrite supply and slow metabolism of Anammox bacteria (AnAOB) impeded the application of Anammox process in low level ammonia (LLA) (≤50 mg/L) wastewater. At the initial concentration of 50 mg/L NH4+-N and 75 mg/L NO3--N, Fe(Ⅱ) (10 mg/L) promoted the total nitrogen removal efficiency from 80.79 to 94.92 % by core-shell sulfurized AnAOB coupled with sulfur oxidizing bacteria (S0@AnAOB + SOB). AnAOB outcompeted SOB for nitrite, because the addition of Fe(Ⅱ) not only increased the nitrate reductase activity (37.54 %), but also enhanced the metabolism and electron capture ability of AnAOB, which was highly related with energy metabolic process: hydrazine dehydrogenase activity increased to 139.00 %. Particularly, Fe(Ⅱ) accelerated the interspecies electron transfer (INET) (from SOB to AnAOB) by stimulating the secretion of redox species and electron hopping in EPS. This study shed light on the mechanism of Fe(Ⅱ) promoting electron transfer in S0@AnAOB + SOB system, and provided basis for engineering practice.

A process-based model for describing redox kinetics of Cr(VI) in natural sediments containing variable reactive Fe(II) species

Sediment-associated Fe(II) is a critical reductant for immobilizing groundwater contaminants, such as Cr(VI). The reduction reactivity of sediment-associated Fe(II) is dependent on its binding environment and influenced by the biogeochemical transformation of other elements (i.e., C, N and Mn), challenging the description and prediction of the reactivity of Fe(II) in natural sediments. Here, anaerobic batch experiments were conducted to study the variation in sediment-associated Fe(II) reactivity toward Cr(VI) in natural sediments collected from an intensive agricultural area located in Guangxi, China, where nitrate is a common surface water and groundwater contaminant. Then, a process-based model was developed to describe the coupled biogeochemical processes of C, N, Mn, Fe, and Cr. In the process-based model, Cr(VI) reduction by sediment-associated Fe(II) was described using a previously developed multirate model, which categorized the reactive Fe(II) into three fractions based on their extractabilities in sodium acetate and HCl solutions. The experimental results showed that Fe(II) generation was inhibited by NO₃^- and/or NO₂^-. After NO₃^- and NO₂^- were exhausted, the Fe(II) content and its reduction rate toward Cr(VI) increased rapidly. As the Fe(II) content increased, the three reactive Fe(II) fractions exhibited approximately linear correlations with aqueous Fe(II) concentrations ( [Formula: see text] ), which was probably driven by sorptive equilibrium and redox equilibrium between aqueous and solid phases. The model results indicated that the reaction rate constants of the three Fe(II) fractions (k_n) significantly increased with incubation time, and log(k_n) correlated well with [Formula: see text] [ [Formula: see text] , [Formula: see text] and [Formula: see text] ]. The numerical model developed in this study provides an applicable method to describe and predict Cr(VI) removal from groundwater under dynamic redox conditions.

Achieving deep autotrophic nitrogen removal in aerated biofilter driven by sponge iron: Performance and mechanism

Different from anammox, the combination of Fe (III) reduction coupled to anaerobic ammonium oxidation (Feammox) and nitrate/nitrite dependent ferrous oxidation (NDFO) do not require to control nitrite accumulation. Furthermore, sponge iron can avoid continuous iron supplementation in practice and is a good iron source for the occurrence of Feammox and NDFO in wastewater treatment. Therefore, a biofilter using sponge iron as carrier treating low nitrogen wastewater was built. In this study, the performances of nitrogen removal were explored under different hydraulic retention times (HRT) and gas-water ratios in sponge iron biofilter. And the pathways of nitrogen removal were analyzed by activity tests. The results showed ammonia removal efficiency reached 94.1% and total inorganic nitrogen removal efficiency was up to 70.6% at HRT of 19 h and gas-water ratio of 18. Compared to nitrogen removal by adsorption under non-aeration, the activity tests showed that total inorganic nitrogen loss was caused by Feammox and NDFO after aeration. The results of microbial communities showed that appearances of nitrifier-Nitrosomonadaceae, Feammox bacteria-Clostridiaceae and NDFO bacteria-Gallionellaceae resulted in deep nitrogen removal after aeration, in which Nitrosomonadaceae and Clostridiaceae contributed to ammonia removal and Gallionellaceae contributed to nitrite/nitrate reduction to nitrogen gas. Therefore, it was feasible to achieve deep autotrophic nitrogen removal and Fe (II) and Fe (III) cycle in sponge iron biofilter.

Synchronous N and P Removal in Carbon-Coated Nanoscale Zerovalent Iron Autotrophic Denitrification─The Synergy of the Carbon Shell and P Removal

Fe⁰ is a promising electron donor for autotrophic denitrification in the simultaneous removal of nitrate and phosphorus in low C/N wastewater. However, P removal may inevitably inhibit bio-denitrification. It has not been well recognized and led to an overdose of iron materials. This study employed carbon-coated zerovalent iron (Fe⁰@C) to support autotrophic denitrification to mitigate the inhibition effects of P removal and enhance both N and P removal. The critical role of the carbon shell in Fe⁰@C was to block the direct contact between Fe⁰ and P and NO₃^--N, to maintain the Fe⁰ activity. Besides, P inhibited the chemical reduction of NO₃^--N by competing for Fe⁰ active sites. This indirectly boosted H₂ generation and promoted bio-denitrification. P removal displayed negligible effects on microbial species but indirectly enhanced the nitrogen metabolic activities because of promoted H₂ in Fe⁰@C-based autotrophic denitrification. Bio-denitrification, in turn, strengthened Fe-P co-precipitation by promoting the formation of ferric hydroxide as a secondary adsorbent for P removal. This study demonstrated an efficient method for simultaneous N and P removal in autotrophic denitrification and revealed the synergistic interactions among N and P removal processes.

Unchanged nitrate and nitrite isotope fractionation during heterotrophic and Fe(II)-mixotrophic denitrification suggest a non-enzymatic link between denitrification and Fe(II) oxidation

Natural-abundance measurements of nitrate and nitrite (NO_x) isotope ratios (δ¹⁵N and δ¹⁸O) can be a valuable tool to study the biogeochemical fate of NO_x species in the environment. A prerequisite for using NO_x isotopes in this regard is an understanding of the mechanistic details of isotope fractionation (¹⁵ε, ¹⁸ε) associated with the biotic and abiotic NO_x transformation processes involved (e.g., denitrification). However, possible impacts on isotope fractionation resulting from changing growth conditions during denitrification, different carbon substrates, or simply the presence of compounds that may be involved in NO_x reduction as co-substrates [e.g., Fe(II)] remain uncertain. Here we investigated whether the type of organic substrate, i.e., short-chained organic acids, and the presence/absence of Fe(II) (mixotrophic vs. heterotrophic growth conditions) affect N and O isotope fractionation dynamics during nitrate (NO₃^–) and nitrite (NO₂^–) reduction in laboratory experiments with three strains of putative nitrate-dependent Fe(II)-oxidizing bacteria and one canonical denitrifier. Our results revealed that ¹⁵ε and ¹⁸ε values obtained for heterotrophic (¹⁵ε-NO₃^–: 17.6 ± 2.8‰, ¹⁸ε-NO₃^–:18.1 ± 2.5‰; ¹⁵ε-NO₂^–: 14.4 ± 3.2‰) vs. mixotrophic (¹⁵ε-NO₃^–: 20.2 ± 1.4‰, ¹⁸ε-NO₃^–: 19.5 ± 1.5‰; ¹⁵ε-NO₂^–: 16.1 ± 1.4‰) growth conditions are very similar and fall within the range previously reported for classical heterotrophic denitrification. Moreover, availability of different short-chain organic acids (succinate vs. acetate), while slightly affecting the NO_x reduction dynamics, did not produce distinct differences in N and O isotope effects. N isotope fractionation in abiotic controls, although exhibiting fluctuating results, even expressed transient inverse isotope dynamics (¹⁵ε-NO₂^–: –12.4 ± 1.3 ‰). These findings imply that neither the mechanisms ordaining cellular uptake of short-chain organic acids nor the presence of Fe(II) seem to systematically impact the overall N and O isotope effect during NO_x reduction. The similar isotope effects detected during mixotrophic and heterotrophic NO_x reduction, as well as the results obtained from the abiotic controls, may not only imply that the enzymatic control of NO_x reduction in putative NDFeOx bacteria is decoupled from Fe(II) oxidation, but also that Fe(II) oxidation is indirectly driven by biologically (i.e., via organic compounds) or abiotically (catalysis via reactive surfaces) mediated processes co-occurring during heterotrophic denitrification.

Biological denitrification potential of cellulase-producing Cupriavidus sp. ZY7 and denitrifying Aquabacterium sp. XL4 at low carbon-to-nitrogen ratio: Performance and synergistic properties

This study emphasizes on the cellulase production characteristics of strain ZY7 and its collaboration with nitrate-dependent ferrous oxidizing (NFO) strain XL4 to achieve efficient denitrification at low carbon-to-nitrogen (C/N) ratio. Results indicated that the denitrification efficiency increased from 65.47 to 97.99% at 24 h after co-culture at C/N of 1.0. Three-dimensional fluorescence excitation-emission matrix (3D-EEM) showed significant changes in the intensity of soluble microbial products (SMP), fulvic-like materials, and aromatic proteins after co-culture. Bio-precipitates were characterized by Scanning electron microscope (SEM), Fourier transform infrared spectrometer (FTIR), and X-ray diffraction (XRD), which showed that cellulose structure was disrupted and the metabolites were potential carbon source for denitrification. In addition, cellulase activity suggested that the hydrolysis of β-1,4-glycosidic bonds and oligosaccharides may be the rate-limiting steps in cellulose degradation. This work promoted the understanding of denitrification characteristics of co-culture and expanded the application of cellulose degrading bacteria in sewage treatment.

Use of sponge iron as an indirect electron donor to provide ferrous iron for nitrate-dependent ferrous oxidation processes: Denitrification performance and mechanism

Sponge iron (SI) can serve as an indirect electron donor to provide Fe(II) for the nitrate-dependent ferrous oxidation (NDFO) process, producing OH^- and magnetite. The SI-NDFO system mainly uses Fe(OH)₂ as an electron donor, achieving a TN reduction rate of 0.42 mg-TN/(gVSS·h) for a period of at least 90 days. The enrichment of iron-oxidizing bacteria and the competition of iron-carbon micro-electrolysis for reaction sites on the surface of SI are the main reasons for the improvement of total nitrogen removal efficiency (TNRE). With an influent NO₃^--N concentration of 50 mg/L and a SI concentration of 50 g/L (at pH 5.0 and 30 °C), the TNRE reached a maximum level of 38.28%. In addition, reducing the pH environment was found to improve the denitrification efficiency of the SI-NDFO system, although denitrification stability was also reduced as a result. Overall, the SI-mediated NDFO process is a promising technique.

Simultaneous heterotrophic and FeS2-based ferrous autotrophic denitrification process for low-C/N ratio wastewater treatment: Nitrate removal performance and microbial community analysis

Heterotrophic-autotrophic denitrification reduces the cost of wastewater treatment and the risk of excess chemical oxygen demanded (COD) in the effluent. A mixotrophic denitrification system involving mixed heterotrophic and ferrous autotrophic bacteria was investigated to treat low-C/N ratio (C/N, defined as chemical oxygen demand (COD)/total nitrogen (TN)) wastewater with pyrite and organic carbon as electron donors. The system yielded effluent total nitrogen (TN) of 0.38 mg/L in 48 h due to a synergistic effect when the C/N ratio was 0.5 and influent nitrate nitrogen (NO₃^--N) was 20 mg/L; this TN value was significantly lower than those of the heterotrophic system (14.08 mg/L) and ferrous autotrophic system (12.00 mg/L). The highest abundance of the narG gene was observed in the mixotrophic denitrification system, along with more abundant microbial species. The dominant denitrification bacteria in each system included Thaurea, Ferritrophicum, Pseudomonas, and Thiobacillus, which varied with the initial inoculum source and the environment. Nevertheless, the abundance of the heterotrophic bacteria Thaurea decreased with prolonged operation of the systems. Together, these results implied that the simultaneous heterotrophic and FeS₂-based ferrous autotrophic denitrification process can be an alternative approach for the treatment of low-C/N ratio wastewater.

Autotrophic Fe-Driven Biological Nitrogen Removal Technologies for Sustainable Wastewater Treatment

Fe-driven biological nitrogen removal (FeBNR) has become one of the main technologies in water pollution remediation due to its economy, safety and mild reaction conditions. This paper systematically summarizes abiotic and biotic reactions in the Fe and N cycles, including nitrate/nitrite-dependent anaerobic Fe(II) oxidation (NDAFO) and anaerobic ammonium oxidation coupled with Fe(III) reduction (Feammox). The biodiversity of iron-oxidizing microorganisms for nitrate/nitrite reduction and iron-reducing microorganisms for ammonium oxidation are reviewed. The effects of environmental factors, e.g., pH, redox potential, Fe species, extracellular electron shuttles and natural organic matter, on the FeBNR reaction rate are analyzed. Current application advances in natural and artificial wastewater treatment are introduced with some typical experimental and application cases. Autotrophic FeBNR can treat low-C/N wastewater and greatly benefit the sustainable development of environmentally friendly biotechnologies for advanced nitrogen control.

Denitrification performance of nitrate-dependent ferrous (Fe2+) oxidizing Aquabacterium sp. XL4: Adsorption mechanisms of bio-precipitation of phenol and estradiol

In this study, a nitrate-dependent ferrous (Fe²⁺) oxidizing strain under anaerobic conditions was selected and identified as XL4, which belongs to Aquabacterium. The Box-Behnken design (BBD) was used to optimize the growth conditions of strain XL4, and the nitrate removal efficiency of strain XL4 (with 10% inoculation dosage, v/v) could reach 91.41% under the conditions of 30.34 ℃, pH of 6.91, and Fe²⁺ concentration of 19.69 mg L^-1. The results of Fluorescence excitation-emission matrix spectra (EEM) revealed that the intensity of soluble microbial products (SMP), aromatic proteins and the fulvic-like materials were obvious difference under different Fe²⁺ concentration, pH, and temperature. X-ray diffraction (XRD) data confirmed that the main components of bio-precipitation were Fe₃O₄ and FeO(OH), which were believed to be responsible for the adsorption of phenol and estradiol. Furthermore, the maximum adsorption capacity of bio-precipitation for phenol and estradiol under the optimal conditions were 192.6 and 65.4 mg g^-1, respectively. On the other hand, the adsorption process of phenol and estradiol by bio-precipitation confirmed to the pseudo-second-order and Langmuir model, which shows that the adsorption process is chemical adsorption and occurs on the uniform surface.

Activated carbon as an insoluble electron shuttle to enhance the anaerobic ammonium oxidation coupled with Fe(III) reduction process

Anaerobic ammonium oxidation coupled with Fe(III) reduction (Feammox) is an autotrophic biological nitrogen removal (BNR) technique in treating low-C/N wastewater. However, the nitrogen removal rate of Feammox is limited by the extracellular electron transfer. In this study, wood activated carbon (AC) was chosen as electron shuttle to enhance the start-up of the Feammox process. Within an operational period of 150 days, the NH₄⁺-N removal efficiency reached 97.9-99.5% with a volumetric loading rate (VLR) of 0.04-0.06 kg N m^-3 d^-1. Batch experiments indicated that compared with Fe₂O₃-AQDS and Fe₂O₃ groups, Fe₂O₃-AC group showed higher catalytic performance and TN removal efficiency reached 85.7%. Quinone (CO) and phenolic (-OH) chemical groups of AC were equipped with electron transfer capacity (76.51 ± 9.27 μmol e^- g^-1). Moreover, Fe(II)/Fe(III) species and the secondary iron minerals were found in our system. Microbial analysis showed that Proteobacteria and Acidobacteriota, which observed with relatively high abundance, were played an important role in the integrated Feammox system. This study demonstrates the significant influence of AC on Feammox process and provides an enhanced biological nitrogen removal strategy for practice engineering application.

A feasibility study of metal sulfide (FeS and MnS) on simultaneous denitrification and chromate reduction

Metal sulfide-based biological process is considered as a promising biotechnology for next-generation wastewater treatment. However, it is not clear if simultaneous bio-reduction of nitrate and chromate was achievable in this process. This study aimed to evaluate the feasibility of metal sulfides (FeS and MnS) on simultaneous denitrification and chromate reduction in autotrophic denitrifying column bioreactors. Results showed that simultaneous reduction of nitrate and chromate was achieved using metal sulfides (FeS and MnS) as electron donors, in which sulfate was the sole soluble end-product. Apart from the sulfur element in the metal sulfides, Fe(II) and Mn(II) were also involved in nitrate and chromate reduction as indicative by the formation of their oxidative states compounds. In microbial communities, SHD-231 and Thiobacillus were the most predominant bacteria, which might have played important roles in simultaneous denitrification and chromate reduction. Compared to FeS, MnS showed a higher performance on nitrate and chromate removal, which could also reduce the toxic inhibition of chromate on nitrate reduction. According to results of XRD and XPS, as well as a lower sulfate production in the FeS system, FeS might have been covered easily to hydroxides due to its bio-oxidation, which limited mass transfer efficiency and bio-availability of FeS. The findings in this study offered insights in the development of promising approaches for the treatment of toxic and hazardous compounds using metal sulfide.

Can we use mine waste as substrate in constructed wetlands to intensify nutrient removal? A critical assessment of key removal mechanisms and long-term environmental risks

The utilization of natural ores and/or mine waste as substrate in constructed wetlands (CWs) to enhance nutrient removal performance has been gaining high popularity recently. However, the knowledge regarding the long-term feasibility and key removal mechanisms, particularly the potential negative environmental effects of contaminants leached from mine waste is far insufficient. This study, for the first time, performed a critical assessment by using different CWs with three mine waste (coal gangue, iron ore and manganese ore) as substrates in a 385-day experiment treating wastewater with varying nutrient loadings. The results showed that the addition of mine waste in CWs increased removal of total phosphorus (TP) by 17-34%, and total nitrogen (TN) by 11-51%. The higher removal of TP is mainly attributed to the strong binding mechanism of phosphate with the oxides and hydroxides of Mn, Fe and/or Al, which are leached out of mine waste. Moreover, integration of mine waste in CWs also significantly stimulated biofilm establishment and enriched the relative abundance of key functional genes related to the nitrogen cycle, supporting the observed high-rate nitrogen removal. However, leaching of heavy metals (Fe, Mn, Cu and Cr) from the beded mine waste in the experimented CWs was monitored, which further influenced cytoplasmic enzymes and created oxidative stress damage to plants, resulting in a decline of nutrient uptake by plants.

Partial ozonation of returned sludge via high-concentration ozone to reduce excess sludge production: A pilot study

Partial ozonation of returned sludge via high and low concentration of ozone were compared to evaluate their efficiency in excess sludge production reduction. A pilot-scale system of anaerobic/anoxic/oxic (A/A/O) + ozonated sludge recycle (OSR) process was operated for 97 days, to investigate the effects of different ozone concentration (380 mg/L and 150 mg/L) on the nutrient removal capacity, sludge reduction rate, the excess sludge properties including settling, dewatering and anaerobic digestion (AD) performance. It was found that at the same total ozone dosage (13 mg/g MLSS, 25 mg/g MLVSS), the ozone of 380 mg/L achieved much higher organic matters and total excess sludge reduction (41.6% and 25.9%) than 150 mg/L applied (31.0% and 18.2%). It also laid less deterioration effect on the effluent quality and had better nutrient (COD, NH₄⁺-N, TN) removal capacity than 150 mg/L applied. Meanwhile, little difference was found in the settling, dewatering and AD properties of excess sludge from the two A/A/O + OSR processes. Meanwhile, sludge solubilization rate, BIOLOG ECO microplate, 16S rRNA sequencing were applied comprehensively to illustrate the reasons for above advantages of the elevated ozone dosage applied. It was clarified that compared to 150 mg/L, A/A/O + OSR with ozone of 380 mg/L had higher sludge solubilization rate, less impact on bacterial community distribution and utilization capacity of carbon sources in bioreactors.

Application of pyritic sludge with an anaerobic granule consortium for nitrate removal in low carbon systems

Granules recovered from a highly reduced anaerobic digester were capable of active nitrogen removal in the absence of exogenous electron donors, averaging 0.25 mg mgNO3--N /gVSS/d over 546 days of operation. Electron mass balance indicated that about half the influent nitrate was converted to ammonia via DNRA and another half denitrified. This capacity was associated with an onion-like structure of multiple layers enriched in reduced iron and sulfur, and a complex microbial community shown by metagenomic sequencing to consist of multiple physiological groups and associated activities, including methanogenesis, denitrification, dissimilatory nitrate reduction to ammonia (DNRA), iron oxidation and reduction, and sulfur reduction and oxidation. Nitrate reduction was supported by both entrained organic material and reduced iron and sulfur species, corresponding to 2.13 mg COD/gVSS/d. Batch incubations showed that approximately 15% of denitrified nitrate was coupled to the oxidation of sulfur derived from both sulfate respiration and granular material enriched in iron-sulfide. Inhibition of sulfate reduction resulted in redirection of electron flow to methanogenesis and, in combination with other batch tests, showed that these granules supported a complex microbial community in which cryptic redox cycles linked carbon, sulfur, and iron oxidation with nitrate, sulfate, iron, and carbon dioxide reduction. This system shows promise for treatment of nitrate contaminated ground water without addition of an external organic carbon source as well as wastewater treatment in combination with (granular) sludge elimination leading in a net reduction of solid treatment costs.

Recovery of Iron-Dependent Autotrophic Denitrification Activity from Cell-Iron Mineral Aggregation-Induced Reversible Inhibition by Low-Intensity Ultrasonication

Iron-dependent autotrophic denitrification (IDAD) has garnered increasing interests as an efficient method for removing nitrogen from wastewater with a low carbon to nitrogen ratio. However, an inevitable deterioration of IDAD performance casts a shadow over its further development. In this work, the hidden cause for such a deterioration is uncovered, and a viable solution to this problem is provided. Batch test results reveal that the aggregation of microbial cells and iron-bearing minerals induced a cumulative and reversible inhibition on the activity of IDAD sludge. Extracellular polymeric substances were found to play a glue-like role in the cell-iron mineral aggregates, where microbial cells were caged, and their metabolisms were suppressed. Adopting low-intensity ultrasound treatment efficiently restored the IDAD activity by disintegrating such aggregates rather than stimulating the microbial metabolism. Moreover, the ultrasonication-assisted IDAD bioreactor exhibited an advantageous nitrogen removal efficiency (with a maximum enhancement of 72.3%) and operational stability compared to the control one, demonstrating a feasible strategy to achieve long-term stability of the IDAD process. Overall, this work provides a better understanding about the mechanism for the performance deterioration and a simple approach to maintain the stability of IDAD.

Energetics, electron uptake mechanisms and limitations of electroautotrophs growing on biocathodes - A review

Electroautotrophs are microorganisms that can take the electrons needed for energy generation, CO₂ fixation and other metabolic reactions from a polarized electrode. They have been the focus of intense research for its application in wastewater treatment, bioelectrosynthetic processes and hydrogen generation. As a general trend, current densities produced by the electron uptake of these microorganisms are low, limiting their applicability at large scale. In this work, the electron uptake mechanisms that may operate in electroautotrophs are reviewed, aiming at finding possible causes for this low performance. Biomass yields, growth rates and electron uptake rates observed when these microorganisms use chemical electron donors are compared with those typically obtained with electrodes, to explore limitations and advantages inherent to the electroautotrophic metabolism. Also, the factors affecting biofilm development are analysed to show how interfacial interactions condition bacterial adhesion, biofilm growth and electrons uptake. Finally, possible strategies to overcome these limitations are described.

Impact of Periodic Polarization on Groundwater Denitrification in Bioelectrochemical Systems

Nitrate contamination is a common problem in groundwater around the world. Nitrate can be cathodically reduced in bioelectrochemical systems using autotrophic denitrifiers with low energy investment and without chemical addition. Successful denitrification was demonstrated in previous studies in both microbial fuel cells and microbial electrolysis cells (MECs) with continuous current flow, whereas the impact of intermittent current supply (e.g., in a fluidized-bed system) on denitrification and particularly the electron-storing capacity of the denitrifying electroactive biofilms (EABs) on the cathodes have not been studied in depth. In this study, two continuously fed MECs were operated in parallel under continuous and periodic polarization modes over 280 days, respectively. Under continuous polarization, the maximum denitrification rate reached 233 g NO₃^--N/m³/d with 98% nitrate removal (0.6 mg NO₃^--N/L in the effluent) with negligible intermediate production, while under a 30 s open-circuit/30 s polarization mode, 86% of nitrate was removed at a maximum rate of 205 g NO₃^--N/m³/d (4.5 mg NO₃^--N/L in the effluent) with higher N₂O production (6.6-9.3 mg N/L in the effluent). Conversely, periodic polarization could be an interesting approach in other bioelectrochemical processes if the generation of chemical intermediates (partially reduced or oxidized) should be favored. Similar microbial communities dominated byGallionellaceaewere found in both MECs; however, swapping the polarization modes and the electrochemical analyses suggested that the periodically polarized EABs probably developed a higher ability for electron storage and transfer, which supported the direct electron transfer pathway in discontinuous operation or fluidized biocathodes.