Optimizing Lumbar Pedicle Screw Trajectory Utilizing a 3D Printed Drill Guide to Ensure Placement of Pedicle Screws Into Higher Density Bone May Improve Pedicle Screw Pullout Resistance

The Influence of Increased Pedicle Screw Diameter and Thicker Rods on Surgical Results in Adolescents Undergoing Posterior Spinal Fusion for Idiopathic Scoliosis

Background: Modern surgical techniques allow for the correction of spinal deformity, stopping its progression and improving pain relief and social and physical functioning. These instruments have different implant designs, screws, and rod diameters and can be composed of different metal alloys with different hardnesses, which can have a significant impact on the effect of correcting spinal deformities. We designed a retrospective cohort study based on the same surgical technique and spine system using different implant sizes, and compared the results across them. Methods: This is a retrospective review of adolescent idiopathic scoliosis (AIS) patients who underwent posterior spinal fusion (PSF) between 2016 and 2022 with a minimum two-year follow-up (FU) using two spinal implant systems: 5.5 and 6.0 mm diameter screws with double 5.5 mm titanium rods (Group 1 (G1)), and 6.0 and 6.5 mm diameter pedicle screws with double 6.0 mm cobalt-chromium rods (Group 2 (G2)). The evaluated data were as follows: preoperative personal data, radiographic outcomes, complications, and health-related quality of life questionnaire (HRQoL). The parameters were reviewed preoperatively, after the final fusion, and during the FU. Results: The mean age of all 260 patients at surgery was 14.8 years. The average BMI was also similar in both groups and was noted as 21. The mean levels of fusion and screw density were similar in both groups. The mean preoperative major curves (MCs) were 57.6° and 62.5° in G1 and G2, respectively. The mean flexibility of the curves was noted as 35% in G1 and 33% in G2. After definitive surgery, the mean percentage correction of the MC was better in G2 vs. G1, with 74.5% vs. 69.8%, respectively (p < 0.001). At the final FU, the average loss of correction was 5.9° for G1 and 3.2° for G2 (p < 0.001). The mean preoperative (TK) thoracic kyphosis (T2-T5) was 12.2° in G1 and 10.8° in G2. It was corrected to 15.2° in G1 and to 13° in G2. At the FFU, we noted a significant difference in the TK (T2-T5) between the groups, with 16.7° vs. 9.6° for G1 vs. G2, respectively (p < 0.001). Statistical significance was observed between the preoperative sagittal balance and the final follow-up for both groups (p < 0.001). Conclusions: AIS patients surgically treated with screws with a larger diameter and thicker and stiffer rods showed greater correction and postoperative thoracic kyphosis without implant failure. The complication rates, implant density, and clinical outcomes remained similar. The radiographic benefits reported in this cohort study suggest that large-sized screws and stiffer rods for the correction of pediatric spinal deformities are safe and very effective.

3D-printed Titanium Prosthetic Reconstruction of Unilateral Bone Deficiency After Surgical Resection of Tumor Lesions in the Upper Cervical Spine: Clinical Outcomes of Three Consecutive Cases and Narrative Review

MAIN POINTS

Operational excision of tumor lesions in the upper cervical spine remains a tremendous challenge to surgeons due to the local complex anatomic relationships. Meanwhile, no commercially available device has been specially designed to address bone deficiency after surgical resection. Here, we described the reconstruction of unilateral bone deficiency after surgical resection of a giant cell tumor of the tendon sheath originating from the lateral atlantoaxial joint with the employment of a 3D printing technique and reviewed the relevant literature. In our study, 3 patients with giant cell tumor of the tendon sheath in the upper cervical spine achieved complete tumor removal, and received unilateral bone reconstruction with one-armed 3D-printed titanium prosthesis. During the follow-up, these patients remained neurologically intact and got back to a normal life without wearing the braces. Images demonstrated the satisfactory placement of 3D-printed prosthesis with no failure of fixation and no subsidence. In addition, 6 articles describing the employment of 3D-printed prostheses or models for tumor surgery in the upper cervical spine were reviewed, and satisfactory clinical outcomes were reported in these studies. Hence, 3D-printed titanium prosthetic reconstruction of bone deficiency in the upper cervical spine was a safe and effective technique.

LEVEL OF EVIDENCE

Level IV.

Biomechanical characteristics of 2 different posterior fixation methods of bilateral pedicle screws: A finite element analysis

BACKGROUND

To explore the biomechanical characteristics of 2 posterior bilateral pedicle screw fixation methods using finite element analysis.

METHODS

A normal L3-5 finite element model was established. Based on the verification of its effectiveness, 2 different posterior internal fixation methods were simulated: bilateral pedicle screws (model A) were placed in the L3 and L5 vertebral bodies, and bilateral pedicle screws (model B) were placed in the L3, L4, and L5 vertebral bodies. The stability and stress differences of intervertebral discs, endplates, screws, and rods between models were compared.

RESULTS

Compared with the normal model, the maximum stress of the range of motion, intervertebral disc, and endplate of the 2 models decreased significantly. Under the 6 working conditions, the 2 internal fixation methods have similar effects on the stress of the endplate and intervertebral disc, but the maximum stress of the screws and rods of model B is smaller than that of model A.

CONCLUSIONS

Based on these results, it was found that bilateral pedicle screw fixation in 2 vertebrae L3 and L5 can achieve similar stability as bilateral pedicle screw fixation in 3 vertebrae L3, L4, and L5. However, the maximum stress of the screw and rod in model B is less than that in model A, so this internal fixation method can effectively reduce the risk of fracture. The 3-dimensional finite element model established in this study is in line with the biomechanical characteristics of the spine and can be used for further studies on spinal column biomechanics. This information can serve as a reference for clinicians for surgical selection.