Artificial Structural Colors and Applications

Resonant-mode engineering for additive reflective structural colors with high brightness and high color purity

We present quad-layered reflective structural color filters generating vivid additive primary colors by controlling a mode number in a Fabry-Perot (FP) cavity and an anti-reflective (AR) coating layer, thus accomplishing high spectral contrast which is highly demanded in creating sharp colors. The reflection brightness of fabricated structural color filters is over 78% and a color gamut is comparable to the standard color gamut (sRGB). Higher-order resonant modes are exploited yielding a narrow passband with strong suppression of the reflection at shorter and longer wavelength ranges for a green color, while red and blue colors are produced by employing fundamental resonant modes. Besides, the structural color filters maintain both high brightness and high color purity at oblique incidence angles up to 40° due to a small angle of refraction by a cavity medium with high refractive index. Moreover, a large-scale fabrication is enabled owing to the simplicity of a device structure, where thin film deposition is used. The scheme presented in this work may open the door to a number of applications, such as reflective displays, imaging devices, colored photovoltaics, and decorations.

Bioinspired Colorimetric Double Inverse Opal Photonic Crystal Indicators for Ethanol Concentration Sensing in Fermentation Engineering

Photonic crystal-based ethanol concentration indicators with rapid response and brilliant structural color output definitely take a place in colorimetric sensors. Here, based on the H-bond-regulated swelling of acrylate shape memory polymers (SMPs) and the solvent-induced structural color change of the double inverse opal photonic crystals (DIOPCs), new-type photonic crystals (PCs) colorimetric indicators were constructed, exhibiting a span of maximum reflection wavelength (λmax) up to ∼166 nm in response to alcohols with concentrations from 0 to 100 vol %. DIOPC indicators (DIOPCIs) show a rapid response to alcohols (<1.5 s) and output different structural colors (covering from blue to red). The colorimetric sensing mechanism includes the solvent-triggered recovery of the inverse opal skeleton, the cosolvency effect and H-bonds induced swelling/shrinkage of the polymer, the phase separation between polystyrene (PS) microsphere and polymer skeleton, and the light diffraction of DIOPCs. While ensuring a larger λmax span by regulating the H-bond interactions in polymer chains through acrylamide (AAm), AAm-modified DIOPCIs are sensitive to some specific ethanol concentrations. The real-time sensing of ethanol concentration during fermentation verified the practicability of DIOPCIs, thus establishing a visual model between structural color and corresponding fermentation kinetics. We envisage that the DIOPCIs will contribute to the intelligentization of the alcoholic fermentation and distillation industry.

MXenes for Bioinspired Soft Actuators: Advancements in Angle-Independent Structural Colors and Beyond

Soft actuators have garnered substantial attention in current years in view of their potential appliances in diverse domains like robotics, biomedical devices, and biomimetic systems. These actuators mimic the natural movements of living organisms, aiming to attain  enhanced flexibility, adaptability, and versatility. On the other hand, angle-independent structural color has been achieved through innovative design strategies and engineering approaches. By carefully controlling the size, shape, and arrangement of nanostructures, researchers have been able to create materials exhibiting consistent colors regardless of the viewing angle. One promising class of materials that holds great potential for bioinspired soft actuators is MXenes in view of their exceptional mechanical, electrical, and optical properties. The integration of MXenes for bioinspired soft actuators with angle-independent structural color offers exciting possibilities. Overcoming material compatibility issues, improving color reproducibility, scalability, durability, power supply efficiency, and cost-effectiveness will play vital roles in advancing these technologies. This perspective appraises the development of bioinspired MXene-centered soft actuators with angle-independent structural color in soft robotics.

Determining intrinsic potentials and validating optical binding forces between colloidal particles using optical tweezers

Understanding the interactions between small, submicrometer-sized colloidal particles is crucial for numerous scientific disciplines and technological applications. In this study, we employ optical tweezers as a powerful tool to investigate these interactions. We utilize a full image reconstruction technique to achieve high precision in characterizing particle pairs that enable nanometer-scale measurement of their positions. This approach captures intricate details and provides a comprehensive understanding of the spatial arrangement between particles, overcoming previous limitations in resolution. Moreover, our research demonstrates that properly accounting for optical binding forces to determine the intrinsic interaction potential is vital. We employ a discrete dipole approximation approach to calculate optical binding potentials and achieve a good agreement between the calculated and observed binding forces. We incorporate the findings from these simulations into the assessment of the intrinsic interaction potentials and validate our methodology by using short-range depletion attraction induced by micelles as an example.

A Biomimetic Cardiac Fibrosis-on-a-Chip as a Visible Disease Model for Evaluating Mesenchymal Stem Cell-Derived Exosome Therapy

Cardiac fibrosis acts as a serious worldwide health issue due to its prevalence in numerous forms of cardiac disease and its essential link to cardiac failure. Considering the efficiency of stem cell therapy for cardiac fibrosis, great efforts have been dedicated to developing accurate models for investigating their underlying therapeutic mechanisms. Herein we present an elaborate biomimetic cardiac fibrosis-on-a-chip based on Janus structural color film (SCF) to provide microphysiological visuals for stem cell therapeutic studies. By coculturing cardiomyocytes (CMs) and cardiac fibroblasts (FBs) on Janus SCF with fibrosis induction, the chip can recreate physiological intercellular crosstalk within the fibrotic microenvironment, elucidating the physiological alterations of fibrotic hearts. In particular, the Janus structural color film possesses superior perceptual capabilities for capturing and responding to a weak cardiac force, demonstrating synchronized structural color shifts. Based on these features, we have not only explored the dynamic relationship between color mapping and the evaluated disease phenotype but also demonstrated the self-reporting capacity of the cardiac fibrosis-on-a-chip for the assessment of mesenchymal stem cell-derived exosome therapy. These features suggest that such a chip can potentially facilitate the evolution of precision medicine strategies and create a protocol for preclinical cardiac drug screening.

Hierarchical Assembly of Patternable Chiroptical Biotextiles with Extreme Environment Stability

Flexible photonic textiles constructed by sustainable cholesteric organization are very promising to achieve a combination of chiroptical structural colors, mechanical robustness, sustainability, and environment stability. However, the efficient assembly of well-ordered cholesteric nanoarchitectures on flexible textiles in a scalable and patternable manner remains a grand challenge. In this study, we develop an efficient and scalable approach to construct large area chiroptical biotextiles using renewable and bioenabled cellulose nanocrystals (CNCs) as building blocks. This hierarchical assembly enables cholesteric photonic CNCs "cast" in situ, in a seamlessly tessellated design, onto topography-tailored textiles to form a strong interlocked multilayered structure. The resulting hierarchical architecture not only comprises strong photonic-photonic coupling to synergistically enhance the chiroptical properties with tunable wavelengths but also leads to impressive mechanical and optical stability against external mechanical forces and extreme environments. More importantly, through regulating the localized photonic band of the preformed chiroptical textiles by small molecules (e.g., water and glucose), customized colored patterns can be easily generated in large scale that are highly responsive to multistimuli, including chiral polarized light, view angle, and solvent. This chiroptical biotextile is a promising next-generation biomimetic photonic material for defense, aviation, and marine and aerospace special applications.

Resonant-Cavity-Enhanced Electrochromic Materials and Devices

With rapid advances in optoelectronics, electrochromic materials and devices have received tremendous attentions from both industry and academia for their strong potentials in wearable and portable electronics, displays/billboards, adaptive camouflage, tunable optics, and intelligent devices, etc. However, conventional electrochromic materials and devices typically present some serious limitations such as undesirable dull colors, and long switching time, hindering their deeper development. Optical resonators have been proven to be the most powerful platform for providing strong optical confinement and controllable lightmatter interactions. They generate locally enhanced electromagnetic near-fields that can convert small refractive index changes in electrochromic materials into high-contrast color variations, enabling multicolor or even panchromatic tuning of electrochromic materials. Here, resonant-cavity-enhanced electrochromic materials and devices, an advanced and emerging trend in electrochromics, are reviewed. In this review, w e will focus on the progress in multicolor electrochromic materials and devices based on different types of optical resonators and their advanced and emerging applications, including multichromatic displays, adaptive visible camouflage, visualized energy storage, and applications of multispectral tunability. Among these topics, principles of optical resonators, related materials/devices and multicolor electrochromic properties are comprehensively discussed and summarized. Finally, the challenges and prospects for resonant-cavity-enhanced electrochromic materials and devices are presented.

Tensor completion algorithm-aided structural color design

In recent years, structural color has developed rapidly due to its distinct advantages, such as low loss, high spatial resolution and environmental friendliness. Various inverse design methods have been extensively investigated to efficiently design optical structures. However, the optimization method for the inverse design of structural color remains a formidable challenge. Traditional optimization approaches, such as genetic algorithms require time-consuming repetitions of structural simulations. Deep learning-assisted design necessitates prior simulations and large amounts of data, making it less efficient for systems with a small number of features. This study proposes a tensor completion algorithm capable of swiftly and accurately predicting missing datasets based on partially obtained datasets to assist in structural color design. Transforming the complex physical problem of structural color design into a spatial structure relationship problem linking geometric parameters and spectral data. The method utilizes tensor multilinear data analysis to effectively capture the complex relationships associated with geometric parameters and spectral data in higher-order data. Numerical and experimental results demonstrate that the algorithm exhibits high reliability in terms of speed and accuracy for diverse structures, datasets of varying sizes, and different materials, significantly enhancing design efficiency. The proposed algorithm offers a viable solution for inverse design problems involving complex physical systems, thereby introducing a novel approach to the design of photonic devices. Additionally, numerical experiments illustrate that the structural color of cruciform resonators with diamond can overcome the high loss issues observed in traditional dielectric materials within the blue wavelength region and enhance the corrosion resistance of the structure. We achieve a wide color gamut and a high-narrow reflection spectrum nearing 1 by this structure, and the theoretical analysis further verifies that diamond holds great promise in the realm of optics.

3D gradient printing based on digital light processing

3D gradient printing is a type of fabrication technique that builds three-dimensional objects with gradually changing properties. Gradient digital light processing based 3D printing has garnered considerable attention in recent years. This function-oriented technology precisely manipulates the performance of different positions of materials and prints them as a monolithic structure to realize specific functions. This review presents a conceptual understanding of gradient properties, covering an overview of current techniques and materials that can produce gradient structures, as well as their limitations and challenges. The principle of digital light processing (DLP) technology and feasible strategies for 3D gradient printing to overcome any barriers are also presented. Additionally, this review discusses the promising future of 4D bioprinting systems based on DLP printing.

Quantum-dot light-chip micro-spectrometer

Micro-spectrometers have great potential in various fields such as medicine, agriculture, and aerospace. In this work, a quantum-dot (QD) light-chip micro-spectrometer is proposed in which QDs emit different wavelengths of light that are combined with a spectral reconstruction (SR) algorithm. The QD array itself can play the roles of both the light source and the wavelength division structure. The spectra of samples can be obtained by using this simple light source with a detector and algorithm, and the spectral resolution reaches 9.7 nm in the wavelength range from 580 nm to 720 nm. The area of the QD light chip is 4 × 7.5 mm², which is 20 times smaller than the halogen light sources of commercial spectrometers. It does not need a wavelength division structure and greatly reduces the volume of the spectrometer. Such a micro-spectrometer can be used for material identification: in a demonstration, three kinds of transparent samples, real and fake leaves, and real and fake blood were classified with an accuracy of 100%. These results indicate that the spectrometer based on a QD light chip has broad application prospects.

Aperture-Controlled Fabrication of All-Dielectric Structural Color Pixels

While interference colors have been known for a long time, conventional color filters have large spatial dimensions and cannot be used to create compact pixelized color pictures. Here we report a simple yet elegant interference-based method of creating microscopic structural color pixels using a single-mask process using standard UV photolithography on an all-dielectric substrate. The technology makes use of the varied aperture-controlled physical deposition rate of low-temperature silicon dioxide inside a hollow cavity to create a thin-film stack with the controlled bottom layer thickness. The stack defines which wavelengths of the reflected light interfere constructively, and thus the cavities act as micrometer-scale pixels of a predefined color. Combinations of such pixels produce vibrant colorful pictures visible to the naked eye. Being fully CMOS-compatible, wafer-scale, and not requiring costly electron-beam lithography, such a method paves the way toward large scale applications of structural colors in commercial products.

High-performance circular polarization modulation using a dielectric metasurface

We demonstrate a chiral metasurface that exhibits a giant chiroptical response as well as functions as an optical diode due to geometrical asymmetry for circularly polarized light (CPL). Engineering the Mie-type multipole radiation using geometrical features led to performance values in terms of near-unity transmission and circular dichroism (CD) efficiency (about 0.96) and an extinction ratio of  ∼3.8×104 for 1550 nm wavelength. A continuous stopband of 1538-1556 nm is achieved for an unchosen component of CPL while keeping the transmission efficiency of the chosen CPL component larger than 0.9. Because of the high extinction ratio and CD efficiency, the proposed metasurface has the potential for chiroptical applications including high-contrast polarization imaging, precise Stokes parameters measurement, optical diodes, and polarization detection for CPL.

Ultrasensitive enhanced Raman spectroscopy by hybrid surface-enhanced and interference-enhanced Raman scattering with metal-insulator-metal structures

High-sensitivity, reproducible, and low-cost substrate has been a major obstacle for practical sensing application of surface-enhancement Raman scattering (SERS). In this work, we report a type of simple SERS substrate which is composed of metal-insulator-metal (MIM) structure of Ag nanoisland (AgNI)-SiO₂-Ag film (AgF). The substrates are fabricated by only evaporation and sputtering processes, which are simple, fast and low-cost. By combining the hotspots and interference-enhanced effects in AgNIs and the plasmonic cavity (SiO₂) between AgNIs and AgF, the proposed SERS substrate shows an enhancement factor (EF) of 1.83 × 10⁸ with limit of detection (LOD) down to 10^-17mol/L for rhodamine 6 G (R6G) molecules. The EFs are ∼18 times higher than that of conventional AgNIs without MIM structure. In addition, the MIM structure shows excellent reproducibility with relative standard deviation (RSD) less than 9%. The proposed SERS substrate is fabricated only with evaporation and sputtering technique and the conventionally used lithographic methods or chemical synthesis are not required. This work provides a simple way to fabricate ultrasensitive and reproducible SERS substrates which show great promise for developing various biochemical sensors with SERS.

Determination of total phosphorus concentration in water by using visible-near-infrared spectroscopy with machine learning algorithm

Total phosphorus (TP) content is a crucial evaluation parameter for surface water quality assessment, which is one of the primary causes of eutrophication. High-accuracy, fast-speed approach for the determination of low-concentration TP in water is important. We proposed a rapid, highly sensitive, and pollution-free approach that combines spectroscopy with a machine learning algorithm we improved called synergy interval Extra-Trees regression (siETR) to determine TP concentration in water. Results show that the prediction model based on siETR can get a high coefficient of determination of prediction ([Formula: see text] = 0.9444) and low root mean square error of prediction (RMSEP = 0.0731), which performs well on the prediction of TP concentration. Furthermore, the statistical analysis results further prove that the model based on siETR is superior to other models we studied both in prediction accuracy and robustness. What is more, the prediction model we established with only 140 characteristic wavelengths has the potential for the development of miniature spectral detection instruments, which is expected to achieve in situ determination of TP concentration. These results indicate that Vis-NIR spectroscopy combined with siETR is a promising approach for the determination of TP concentration in water.

3D printing of responsive chiral photonic nanostructures

Finely controlled flow forces in extrusion-based additive manufacturing can be exploited to program the self-assembly of malleable nanostructures in soft materials by integrating bottom-up design into a top-down processing approach. Here, we leverage the processing parameters offered by direct ink-writing (DIW) to reconfigure the photonic chiral nematic liquid crystalline phase in hydroxypropyl cellulose (HPC) solutions prior to deposition on the writing substrate to direct structural evolution from a particular initial condition. Moreover, we incorporate polyethylene glycol (PEG) into iridescent HPC inks to form a physically cross-linked network capable of inducing kinetic arrest of the cholesteric/chiral pitch at length scales that selectively reflect light throughout the visible spectrum. Based on thorough rheological measurements, we have found that printing the chiral inks at a shear rate where HPC molecules adopt pseudonematic state results in uniform chiral recovery following flow cessation and enhanced optical properties in the solid state. Printing chiral inks at high shear rates, on the other hand, shifts the monochromatic appearance of the extruded filaments to a highly angle-dependent state, suggesting a preferred orientation of the chiral domains. The optical response of these filaments when exposed to mechanical deformation can be used in the development of optical sensors.

Magnetically Tunable One-Dimensional Plasmonic Photonic Crystals

Integrating plasmonic resonance into photonic bandgap nanostructures promises additional control over their optical properties. Here, one-dimensional (1D) plasmonic photonic crystals with angular-dependent structural colors are fabricated by assembling magnetoplasmonic colloidal nanoparticles under an external magnetic field. Unlike conventional 1D photonic crystals, the assembled 1D periodic structures show angular-dependent colors based on the selective activation of optical diffraction and plasmonic scattering. They can be further fixed in an elastic polymer matrix to produce a photonic film with angular-dependent and mechanically tunable optical properties. The magnetic assembly enables precise control over the orientation of the 1D assemblies within the polymer matrix, producing photonic films with designed patterns displaying versatile colors from the dominant backward optical diffraction and forward plasmonic scattering. The combination of optical diffraction and plasmonic properties within a single system holds the potential for developing programmable optical functionalities for applications in various optical devices, color displays, and information encryption systems.

Structural color modulation by laser post-processing on metal-coated colloidal crystals

A method to use a pulsed solid-state laser to create structural color modulation on metal-coated colloidal crystal surfaces by changing the scanning speed has been proposed. Vivid colors as cyan, orange, yellow, and magenta are obtained with different predefined stringent geometrical and structural parameters. The effect of laser scanning speeds and polystyrene (PS) particle sizes on the optical properties is studied, and the angle-dependent property of the samples is also discussed. As a result, the reflectance peak is progressively red shifted along with increasing the scanning speed from 4 mm/s to 200 mm/s with 300 nm PS microspheres. Moreover, the influence of the microsphere particle sizes and incident angle are also experimentally investigated. For 420 and 600 nm PS colloidal crystals, along with a gradual decrease in the scanning speed of the laser pulse from 100 mm/s to 10 mm/s and an increase in the incident angle from 15° to 45°, there was a blue shift for two reflection peak positions. This research is a key, low-cost step toward applications in green printing, anti-counterfeiting, and other related fields.

High-quality factor mid-infrared absorber based on all-dielectric metasurfaces

The absorption spectrum of metasurface absorbers can be manipulated by changing structures. However, narrowband performance absorbers with high quality factors (Q-factor) are hard to achieve, mainly for the ohmic loss of metal resonators. Here, we propose an all-dielectric metasurface absorber with narrow absorption linewidth in the mid-infrared range. Magnetic quadrupole resonance is excited in the stacked Ge-Si₃N₄ nanoarrays with an absorption of 89.6% and a Q-factor of 6120 at 6.612 µm. The separate lossless Ge resonator and lossy Si₃N₄ layer realize high electromagnetic field gain and absorption, respectively. And the proposed method successfully reduced the intrinsic loss of the absorber, which reduced the absorption beyond the resonant wavelength and improved the absorption efficiency of Si₃N₄ in the low loss range. Furthermore, the absorption intensity and wavelength can be modulated by adjusting the geometric parameters of the structure. We believe this research has good application prospects in mid-infrared lasers, thermal emitters, gas feature sensing, and spectral detection.

"Plasma-Structural Coloring" of Penciling on a Paper

The penciling part on a paper is colored by the formation of structural color, and the coloring of a paper without ink has been achieved. In a previous study, our group reported that structural color is formed by plasma irradiation (40-120 s) of the surface of a pencil lead or paper painted with a pencil. The formation of structural color due to the thin-layer interference of components of the pencil lead was observed. The clay exposed by removal of the surface graphite through plasma etching plays the role of a "thin layer". The pencil lead can be colored blue, red, and green by the method. In the case of the paper painted with a pencil (6B), the paper turned blue but could not form the other colors by the method. The reason is that the graphite layer on the paper is not thick enough to form thin-layer interference to show colors other than blue. We now present the method that forms structural colors by plasma irradiation of the paper painted by a graphite-rich pencil lead (9B and 12B). The formation of various structural colors, such as blue, yellow, red-purple, and green, on the paper was achieved. The colored site can be effaced by an eraser. This method is a novel coloring method without using colored inks. This environmentallly friendly coloring method can be applied to various activities, such as studies and art, and can contribute to the achievement of a sustainable society.

Broadband and Incident-Angle-Modulation Near-Infrared Polarizers Based on Optically Anisotropic SnSe

Optical anisotropy offers an extra degree of freedom to dynamically and reversibly regulate polarizing optical components, such as polarizers, without extra energy consumption and with high modulating efficiency. In this paper, we theoretically and numerically design broadband and incident-angle-modulation near-infrared polarizers, based on the SnSe, whose optical anisotropy is quantitatively evaluated by the complete dielectric tensor, complex refractive index tensor, and derived birefringence (~|Δn|_max = 0.4) and dichroism (~|Δk|_max = 0.4). The bandwidth of a broadband polarizer is 324 nm, from 1262 nm to 1586 nm, with an average extinction ratio above 23 dB. For the incident-angle-modulation near-infrared polarizer, the high incident angles dynamically and reversibly modulate its working wavelength with a maximum extinction ratio of 71 dB. Numerical simulations and theoretical calculations reveal that the considerable absorption for p light and continuously and relatively low absorption of s light lead to the broadband polarizer, while the incident-angle-modulation one mainly arises from the blue shift of corresponding wavelength of p light's minimum reflectance. The proposed novel design of polarizers based on SnSe are likely to be mass-produced and integrated into an on-chip system, which opens up a new thought to design polarizing optical components by utilizing other low-symmetry materials.

Mie Resonances Enabled Subtractive Structural Colors with Low-Index-Contrast Silicon Metasurfaces

All-dielectric structural colors are attracting increasing attention due to their great potential for various applications in display devices, imaging security certification, optical data storage, and so on. However, it remains a great challenge to achieve vivid structural colors with low-aspect-ratio silicon nanostructures directly on a silicon substrate, which is highly desirable for future integrated optoelectronic devices. The main obstacle comes from the difficulty in achieving strong Mie resonances by Si nanostructures on low-index-contrast substrates. Here, we demonstrate a generic principle to create vivid bright field structural colors by using silicon nanopillars directly on top of the silicon substrate. Complementary colors across the full visible spectrum are achieved as a result of the enhanced absorption due to Mie resonances. It is shown that the color saturation increases with the increasing of the nanopillar height. Remarkably, blue and black colors are generated by trapezoid nanopillar arrays as a result of the absorption at long wavelengths or all visible wavelengths. Our strategy provides a powerful scheme for accelerating the integrated optoelectronic applications in nanoscale color printing, imaging, and displays.

Reversible colorimetric sensing of volatile analytes by wicking in close proximity to a photonic film

Isolation of volatile analytes from environmental or biological fluids is a rate-determining step that can delay the response time for continuous sensing. In this paper, we demonstrate a colorimetric sensing system that enables the rapid detection of gas-phase analytes released from a flowing micro-volume fluid sample. The sensor platform is an analyte-responsive metal-insulator-metal (MIM) thin-film structure integrated with a large area quartz micropillar array. This allows precise planar alignment and microscale separation (310 μm) of the optical and fluidic structures. This configuration offers rapid and homogeneous color changes over large areas that permits detection by low-resolution optics or eye, which is well-suited to portable/wearable devices. For our proof-of-principle demonstration, we utilized a poly(methyl methacrylate) (PMMA) spacer and evaluated the sensor's response (color change) to ethanol vapor. We show that the RGB color value is quantitatively linked to the spacer swelling, which is reversible and repeatable. The optofluidic platform reduces the sensor response time from minutes to seconds compared with experiments using a conventional chamber. The sensor's concentration-dependent response was examined, confirming the potential of the reported sensing platform for continuous, compact, and quantitative colorimetric analysis of volatile analytes in low-volume samples, such as biofluids.

Point-by-point visual enhancement with spatially and spectrally tunable laser illumination

Vision is responsible for most of the information that humans perceive of the surrounding world. Many studies attempt to enhance the visualization of the entire scene by optimizing and tuning the overall illumination spectrum. However, by using a spatially uniform illumination spectrum for the entire scene, only certain global color shifts with respect to a reference illumination spectrum can be realized, resulting in moderate visual enhancement. In this paper, a new visual enhancement method is presented that relies on a spatially variable illumination spectrum. Such an approach can target much more dedicated visual enhancements by optimizing the incident illumination spectrum to the surface reflectance at each position. First, a geometric calibration of the projector-camera system is carried out for determining the spatial mapping from the projected pixel grid to the imaged pixel grid. Secondly, the scene is segmented for implementing the visual enhancement approach. And finally, one of three visual enhancement scenarios is applied by projecting the required color image onto the considered segmented scene. The experimental results show that the visual salience of the scene or region of interest can be efficiently enhanced when our proposed method is applied to achieve colorfulness enhancement, hue tuning, and background lightness reduction.

Security labeling and optical information encryption enabled by laser-printed silicon Mie resonators

Fighting against the falsification of valuable items remains a crucial social-threatening challenge stimulating a never-ending search for novel anti-counterfeiting strategies. The demanding security labels must simultaneously address multiple requirements (high density of the recorded information, high protection degree, etc.) and be realized via scalable and inexpensive technologies. Here, the direct reproducible femtosecond-laser patterning of thin glass-supported amorphous (α-)Si films is proposed for optical information encryption and the scalable and highly reproducible fabrication of security labels composed of Raman-active hemispherical Si nanoparticles (NPs). Laser printing conditions allow the precise control of the diameter of the formed NPs ensuring translation of their dipolar Mie resonance position within the entire visible spectral range. Two-temperature molecular dynamics simulations clarify the origin of α-Si NP formation by rupture of the molten Si layer driven by a negative GPa-range pressure near the liquid-solid interface. Arrangement of the laser-printed Mie-resonant NP allows the creation of hidden security labels offering several easy-to-realize information encryption strategies (for example, local laser-induced post-crystallization or mixing Mie-resonant and non-resonant NPs), additional protection modalities, facile Raman mapping readout and dense information recording (up to 60 000 dots per inch) close to the optical diffraction limit. The developed fabrication strategy is simple, inexpensive, and scalable and can be realized based on cheap Earth-abundant materials and commercially-available equipment justifying its practical applicability and attractiveness for anti-counterfeit and security applications.

Preparation of Acrylic Yarns with Durable Structural Colors Based on Stable Photonic Crystals

Structural coloration of photonic crystals (PCs) is considered an ecological and environmental way to achieve colorful textiles. However, constructing PCs with obvious structural colors on traditional flexible yarns is still a great challenge. As a secondary structure that forms textiles, compared with fibers and fabrics, the yarns are rougher, hindering the construction of regular PCs. In this work, the flexible acrylic yarns with vivid structural colors, named PC-based structural color yarns, were prepared by constructing regular PCs via assembling poly(styrene-butyl acrylate-methacrylate) (P(St-BA-MAA)) colloidal microspheres on yarns. Specifically, the properties of P(St-BA-MAA) colloidal microspheres were investigated. The PCs with better structural stability and obvious structural colors were prepared by presetting the acrylic adhesive layer on yarns. Moreover, the color durability and color regulation methods of prepared PC-based structural color yarns were evaluated and discussed. The results showed that the P(St-BA-MAA) colloidal microspheres exhibited even particle sizes, excellent monodispersity, and a typical hard core-soft shell structure. And the glass-transition temperature (T _g) of the microspheres was tested to be about 65.6 °C. The cationic acrylate regarded as a pretreatment agent could not only improve the combination between the PC layers and the yarns by acting as a "bridge" but also enhance the structural color effect by smoothing the yarn surface. The results showed that when the mass fraction of cationic acrylate was 3 wt %, the microspheres were beneficial to access regular PCs with obvious structural colors. The PCs with bright structural colors could be constructed on black acrylic yarns, and the colors of yarns were still bright after rubbing and washing tests, indicating that the prepared PC-based structural color yarns have good color fastness. Moreover, the color hue of PC-based structural color yarns could be regulated by adjusting the particle sizes and viewing angles. This study provides strategic support for the structural coloration of flexible materials.

Survivability of probiotics encapsulated in kelp nanocellulose/alginate microcapsules on microfluidic device

Probiotics are living microorganisms that can produce health benefits to the host only when they are ingested in sufficient quantities and reach the intestines active state. However, the external environment that probiotics face for a long time before administration and the low pH environment in the stomach after administration can greatly reduce their activity. In this work, we proposed a simple microfluidic encapsulation strategy to efficiently prepare the probiotics-loaded nanocellulose/alginate delivery system, which can improve the storage stability and gastrointestinal survival rate of probiotics. The microcapsules were found to be monodisperse, and the average particle size was<500 μm by observing the microstructure and macroscopic morphology. The kelp nanocellulose was cross-linked in the microcapsule and formed a dense surface with alginate. Through the simulated gastrointestinal digestion experiment, it was found that the survival of probiotics in microcapsules containing 0.5 % and 1.5 % kelp nanocellulose decreased by 1.77 log CFU/g and 1.65 log CFU/g respectively, which was significantly lower than that of nanocellulose-free microcapsules (3.70 log CFU/g). And all the treated groups could release probiotics above 7 log CFU/g after digesting intestinal juice for 6 h. Furthermore, through the storage experiment, it was found that the microcapsules with 1.5 % kelp nanocellulose could still release 8.07 log CFU/g probiotics after four weeks. The results provide a new strategy for probiotics processing and extensive high-value utilization of marine natural products.

Low-cost micro-spectrometer based on a nano-imprint and spectral-feature reconstruction algorithm

Reconstructive micro-spectrometers have shown great potential in many fields such as medicine, agriculture, and astronomy. However, the performance of these spectrometers is seriously limited by the spectral varieties of response pixels and anti-noise ability of reconstruction algorithms. In this work, we propose a spectral reconstruction (SR) algorithm, whose anti-noise ability is at least four times better than the current algorithms. A micro-spectrometer is realized by fabricating a large number of Fabry-Perot (FP) micro-filters onto a cheap complementary metal-oxide semiconductor (CMOS) chip for demonstration by using a very high-efficiency technology of nano-imprinting. Nano-imprint technology can complete hundreds of spectral pixels with rich spectral features at one time and with low cost. In cooperation with the SR algorithm, such a micro-spectrometer can have a spectral resolution as high as 3 nm with much lower angular sensitivity than a photonic crystal-based micro-spectrometer. It can obtain the target's spectrum from only a single shot, which has wide applications in spectral analysis etc.

MEMS cantilever-controlled plasmonic colors for sustainable optical displays

Conventional optical displays using indium tin oxide and liquid crystal materials present challenges for long-term sustainability. We show here a cost-effective and complementary metal-oxide semiconductor (CMOS)-compatible fast and full-range electrically controlled RGB color display. This is achieved by combining transmission-based plasmonic metasurfaces with MEMS (microelectromechanical systems) technology, using only two common materials: aluminum and silicon oxide. White light is filtered into RGB components by plasmonic metasurfaces made of aluminum nanohole arrays. The transmission through each color filter is modulated by MEMS miniaturized cantilevers fabricated with aluminum and silicon oxide on top of the color filters. We show that the relative transmission of a color subpixel can be freely modulated from 35 to 100%. The pixels can also operate well above 800 Hz for future ultrafast displays. Our work provides a road to future circular economic goals by exploiting advances in structural colors and MEMS technologies to innovate optical displays.

Erbium chloride silicate-based vertical cavity surface-emitting laser at the near-infrared communication band

Silicon-based integrated optoelectronics has become a hotspot in the field of computers and information processing systems. An integrated coherent light source on-chip with a small footprint and high efficiency is one of the most important unresolved devices. Here, we realize a silicon-based vertical cavity surface-emitting laser in the near-infrared communication band by making efforts in both controlled preparation of high-gain erbium silicate materials and novel design of high optical feedback microcavity. Single-crystal erbium/ytterbium silicate microplates with erbium concentration as high as 5 × 10²¹ cm^-3 are controlled prepared by a chemical vapor deposition method. They can produce strong luminescence with quite a long lifetime (2.3 ms) at the wavelength of 1.5 μm. By embedding the erbium silicate microplates between two dielectric Bragg reflectors, we construct a vertical cavity surface-emitting laser at 1.5 μm, with a lasing threshold as low as 20 μJ/cm² and Q factor of nearly 2000. Our study provides a new pathway to achieve a sub-micrometer coherent light source for optical communication.

Colloidal cubic diamond photonic crystals through cooperative self-assembly

Colloidal cubic diamond crystals with low-coordinated and staggered structures could display a wide photonic bandgap at low refractive index contrasts, which makes them extremely valuable for photonic applications. However, self-assembly of cubic diamond crystals using simple colloidal building blocks is still considerably challenging, due to their low packing fraction and mechanical instability. Here we propose a new strategy for constructing colloidal cubic diamond crystals through cooperative self-assembly of surface-anisotropic triblock Janus colloids and isotropic colloidal spheres into superlattices. In self-assembly, cooperativity is achieved by tuning the interaction and particle size ratio of colloidal building blocks. The pyrochlore lattice formed by self-assembly of triblock Janus colloids acts as a soft template to direct the packing of colloidal spheres into cubic diamond lattices. Numerical simulations show that this cooperative self-assembly strategy works well in a large range of particle size ratio of these two species. Moreover, photonic band structure calculations reveal that the resulting cubic diamond lattices exhibit wide and complete photonic bandgaps and the width and frequency of the bandgaps can also be easily adjusted by tuning the particle size ratio. Our work will open up a promising avenue toward photonic bandgap materials by cooperative self-assembly employing surface-anisotropic Janus or patchy colloids as a soft template.

Radiolabeling of Nanomaterials: Advantages and Challenges

Quantifying the distribution of nanomaterials in complex samples is of great significance to the toxicological research of nanomaterials as well as their clinical applications. Radiotracer technology is a powerful tool for biological and environmental tracing of nanomaterials because it has the advantages of high sensitivity and high reliability, and can be matched with some spatially resolved technologies for non-invasive, real-time detection. However, the radiolabeling operation of nanomaterials is relatively complicated, and fundamental studies on how to optimize the experimental procedures for the best radiolabeling of nanomaterials are still needed. This minireview looks back into the methods of radiolabeling of nanomaterials in previous work, and highlights the superiority of the “last-step” labeling strategy. At the same time, the problems existing in the stability test of radiolabeling and the suggestions for further improvement are also addressed.

Impact of Albumin Pre-Coating on Gold Nanoparticles Uptake at Single-Cell Level

Nanoparticles (NPs) suspension is thermodynamically unstable, agglomeration and sedimentation may occur after introducing NPs into a physiological solution, which in turn affects their recognition and uptake by cells. In this work, rod-like gold NPs (AuNRs) with uniform morphology and size were synthesized to study the impact of bovine serum albumin (BSA) pre-coating on the cellular uptake of AuNRs. A comparison study using horizontal and vertical cell culture configurations was performed to reveal the effect of NPs sedimentation on AuNRs uptake at the single-cell level. Our results demonstrate that the well-dispersed AuNRs-BSA complexes were more stable in culture medium than the pristine AuNRs, and therefore were less taken up by cells. The settled AuNRs agglomerates, although only a small fraction of the total AuNRs, weighed heavily in determining the average AuNRs uptake at the population level. These findings highlight the necessity of applying single-cell quantification analysis in the study of the mechanisms underlying the cellular uptake of NPs.

Shape Modulation of Plasmonic Nanostructures by Unconventional Lithographic Technique

Conventional nano-sphere lithography techniques have been extended to the fabrication of highly periodic arrays of sub-wavelength nanoholes in a thin metal film. By combining the dry etching processes of self-assembled monolayers of polystyrene colloids with metal physical deposition, the complete transition from increasing size triangular nanoprism to hexagonally distributed nanoholes array onto thin metal film has been gradually explored. The investigated nano-structured materials exhibit interesting plasmonic properties which can be precisely modulated in a desired optical spectral region. An interesting approach based on optical absorbance measurements has been adopted for rapid and non-invasive inspections of the nano-sphere monolayer after the ion etching process. By enabling an indirect and accurate evaluation of colloid dimensions in a large area, this approach allows the low-cost and reproducible fabrication of plasmonic materials with specifically modulated optical properties suitable for many application in biosensing devices or Raman enhanced effects.

Light-Driven Fabrication of a Chiral Photonic Lattice of the Helical Nanofilament Liquid Crystal Phase

A photonic lattice is an efficient platform for optically exploring quantum phenomena. However, its fabrication requires high costs and complex procedures when conventional materials, such as silicon or metals, are used. Here, we demonstrate a simple and cost-effective fabrication method for a reconfigurable chiral photonic lattice of the helical nanofilament (HNF) liquid crystal (LC) phase and diffraction grating showing wavelength-dependent diffraction with a rotated polarization state. Furthermore, the UV-exposed areas of the HNF film having chiral characteristics act as optical building blocks that induce resonant intensity modulation in the reflectance and transmittance modes and the optical rotation of the linear polarization. Our photonic lattice of the HNF can be an efficient platform for a chirality-embedded photonic lattice at a low cost.

Multi-mode plasmonic resonance broadband LWIR metamaterial absorber based on lossy metal ring

Broadband perfect infrared wave absorption of unpolarized light over a wide range of angles in an ultrathin film is critical for applications such as thermal emitters and imaging. Although many efforts have been made in infrared broadband absorption, it is still challenging to cover the perfect absorption of broadband in the long-wave infrared band. We propose a long-wave infrared broadband, polarization, and incident angle insensitivity metamaterial absorber based on the supercell with four rings of two sizes. Broadband absorption covering the long-wave infrared band is realized by combining four PSPRs and LSPRs absorption peaks excited by the supercell structure. The absorptivity of our absorber exceeds 90% in the wavelength range of 7.76∼14µm, and the average absorptivity reaches 93.8%. The absorber maintains more than 80% absorptivity as the incident angle of unpolarized light reaches 60°, which may have promising applications for thermal emitters, infrared imaging, thermal detection.

Micro-/Nano-Structures Fabricated by Laser Technologies for Optoelectronic Devices

Due to unique optical and electrical properties, micro-/nano-structures have become an essential part of optoelectronic devices. Here, we summarize the recent developments in micro-/nano-structures fabricated by laser technologies for optoelectronic devices. The fabrication of micro-/nano-structures by various laser technologies is reviewed. Micro-/nano-structures in optoelectronic devices for performance improvement are reviewed. In addition, typical optoelectronic devices with micro-nano structures are also summarized. Finally, the challenges and prospects are discussed.

Artificial intelligence: A powerful paradigm for scientific research

Artificial intelligence (AI) coupled with promising machine learning (ML) techniques well known from computer science is broadly affecting many aspects of various fields including science and technology, industry, and even our day-to-day life. The ML techniques have been developed to analyze high-throughput data with a view to obtaining useful insights, categorizing, predicting, and making evidence-based decisions in novel ways, which will promote the growth of novel applications and fuel the sustainable booming of AI. This paper undertakes a comprehensive survey on the development and application of AI in different aspects of fundamental sciences, including information science, mathematics, medical science, materials science, geoscience, life science, physics, and chemistry. The challenges that each discipline of science meets, and the potentials of AI techniques to handle these challenges, are discussed in detail. Moreover, we shed light on new research trends entailing the integration of AI into each scientific discipline. The aim of this paper is to provide a broad research guideline on fundamental sciences with potential infusion of AI, to help motivate researchers to deeply understand the state-of-the-art applications of AI-based fundamental sciences, and thereby to help promote the continuous development of these fundamental sciences.

Responsive Janus Structural Color Hydrogel Micromotors for Label-Free Multiplex Assays

Micromotors with self-propelling ability demonstrate great values in highly sensitive analysis. Developing novel micromotors to achieve label-free multiplex assay is particularly intriguing in terms of detection efficiency. Herein, structural color micromotors (SCMs) were developed and employed for this purpose. The SCMs were derived from phase separation of droplet templates and exhibited a Janus structure with two distinct sections, including one with structural colors and the other providing catalytic self-propelling functions. Besides, the SCMs were functionalized with ion-responsive aptamers, through which the interaction between the ions and aptamers resulted in the shift of the intrinsic color of the SCMs. It was demonstrated that the SCMs could realize multiplex label-free detection of ions based on their optical coding capacity and responsive behaviors. Moreover, the detection sensitivity was greatly improved benefiting from the autonomous motion of the SCMs which enhanced the ion-aptamer interactions. We anticipate that the SCMs can significantly promote the development of multiplex assay and biomedical fields.

Dual-band metamaterial absorber with a low-coherence composite cross structure in mid-wave and long-wave infrared bands

The atmospheric window in the infrared (IR) band primarily consists of mid-wave (MWIR, 3-5 μm) and long-wave IR (LWIR, 8-12 μm) bands, also known as the working bands in most of the IR devices. The main factor affecting the device capability includes the absorption efficiency, hence, the absorption material. Herein, a dual-band absorber based on the composite cross structure (CCS) in both MWIR and LWIR bands was proposed, with absorption peaks of 4.28 μm and 8.23 μm. The obtained absorber is with high scalability in the MWIR and LWIR region respectively by tuning the structural parameters. A quadrupole polarization model is proposed for further understanding of the uneven distribution of electromagnetic field that was caused by the change of the center spacing of the embedded structure. Meanwhile, it was shown that the two absorption peaks exhibited good incident angle stability. In addition, as the incident angle of the TM mode increases, a waveguide is formed between the embedded structure and the surface structure, leading to another strong absorption in the LWIR band. The results showed that absorption increases as the incident angle increases. The proposed absorber can be a good candidate for applications in thermal emission, detection and solar energy harvesting.

Polarization-dependent broadband absorber based on composite metamaterials in the long-wavelength infrared range

Capturing polarization information has long been an important topic in the field of detection. In this study, two polarization-dependent broadband absorbers based on a composite metamaterial structure were designed and numerically investigated. Unlike in conventional metamaterial absorbers, the bottom metallic film is functionalized to achieve a polarization response or broadband absorption. The simulation results show that the type I absorber exhibits TM polarization-dependent broadband absorption (absorptivity>80%) from 8.37 µm to 12.12 µm. In contrast, the type II absorber presents TE polarization-dependent broadband absorption (absorptivity>80%) from 8.23 µm to 11.93 µm. These devices are extremely sensitive to the change of polarization angle. The absorptivity changes monotonically with an increase of the polarization angle, but it is insensitive to oblique incidence. This design paves the way for realizing broadband polarization-dependent absorption via a simple configuration. It has bright prospects in thermal detection applications and imaging fields.

Spin-decoupled metasurface for broadband and pixel-saving polarization rotation and wavefront control

In this paper, a strategy to achieve a simultaneous wavefront shaping and polarization rotation, without compromising the number of pixels and energy efficiency as well as having broadband operation range, is proposed. This strategy is based on the application of a spin-decoupled phase metasurface composed by only one set of metal-insulator-metal (MIM) umbrella-shaped chiral unit cells. Quasi-non-dispersive and spin-decoupled phase shift can be achieved simply by changing single structural parameter of the structure. By further merging the Pancharatnam-Berry (PB) geometric phase, conversion of an incident LP light beam into right- and left-handed circularly polarized reflected beams with similar amplitudes, desired phase profiles and controlled phase retardation on a nanoscale is enabled with high efficiency. Based on the proposed strategy, a polarization-insensitive hologram generator with control optical activity, and a multiple ring vortex beam generator are realized. The results obtained in this work provide a simple and pixel-saving approach to the design of integratable and multitasking devices combining polarization manipulation and wavefront shaping functions, such as vectorial holographic generators, multifocal metalenses, and multichannel vector beam generators.