Numerical study of hemodynamics and wall mechanics in distal end-to-side anastomoses of bypass grafts

Distal end side-to-side anastomosis of sequential coronary bypass for size mismatched saphenous vein grafts and coronary arteries

INTRODUCTION

The distal end anastomosis is critical to the entire sequential grafts in coronary artery bypass grafting (CABG), but caliber mismatch diminishes the quality of the anastomosis. We aimed to introduce a modified distal end side-to-side (deSTS) anastomosis to handle the size mismatch and compared with classic distal end end-to-side (deETS) anastomosis.

METHODS

From January 2014 to December 2018, 185 patients who underwent off-pump CABG with size mismatched sequential vein grafts (≥3.5 mm) and target coronaries (1.0-1.5 mm) at the distal end anastomoses were included. We retrospectively reviewed the data of the patients, perioperative and follow-up outcomes were analyzed.

RESULTS

The deSTS group (n = 67) showed higher anastomotic flow (19.8 ± 8.0 vs 14.9±6.8 mL/min; p < 0.001) and lower pulsatility index (2.7 ± 0.8 vs 3.2 ± 1.0; p = 0.001) than the deETS group (n = 118). Higher incidence of in-hospital myocardial infarction (MI) was found in the deETS group but without significant difference (9.0% vs. 15.3%; p = 0.220). Kaplan-Meier analysis illustrated a relatively lower MI and major adverse cardiovascular and cerebrovascular events (MACCE) incidence in the deSTS group, and the deSTS group was associated with a reduction in long-term death, MI and MACCE in the adjusted Cox regression model. In addition, relatively higher graft patency was found in the deSTS group.

CONCLUSIONS

The deSTS anastomosis showed superiority in solving size mismatch in sequential CABG, including better intraoperative flow dynamics, ideal long-term graft patency and reduced the incidence of perioperative and follow-up adverse events especially in MI.

Reduced order methods for parametric optimal flow control in coronary bypass grafts, toward patient-specific data assimilation

Coronary artery bypass grafts (CABG) surgery is an invasive procedure performed to circumvent partial or complete blood flow blockage in coronary artery disease. In this work, we apply a numerical optimal flow control model to patient-specific geometries of CABG, reconstructed from clinical images of real-life surgical cases, in parameterized settings. The aim of these applications is to match known physiological data with numerical hemodynamics corresponding to different scenarios, arisen by tuning some parameters. Such applications are an initial step toward matching patient-specific physiological data in patient-specific vascular geometries as best as possible. Two critical challenges that reportedly arise in such problems are: (a) lack of robust quantification of meaningful boundary conditions required to match known data as best as possible and (b) high computational cost. In this work, we utilize unknown control variables in the optimal flow control problems to take care of the first challenge. Moreover, to address the second challenge, we propose a time-efficient and reliable computational environment for such parameterized problems by projecting them onto a low-dimensional solution manifold through proper orthogonal decomposition-Galerkin.

On the relevance of boundary conditions and viscosity models in blood flow simulations in patient-specific aorto-coronary bypass models

Physiologically realistic results are the aim of every blood flow simulation. This is not different in aorto-coronary bypasses where the properties of the coronary circulation may significantly affect the relevance of the performed simulations. By considering three patient-specific bypass geometries, the present article focuses on two aspects of the coronary blood flow - its phasic flow pattern and its behaviour affected by blood rheology. For the phasic flow property, a multiscale modelling approach is chosen as a means to assess the ability of five different types of coronary boundary conditions (mean arterial pressure, Windkessel model and three lumped parameter models) to attain realistic coronary haemodynamics. From the analysed variants of boundary conditions, the best option in terms of physiological characteristics and its potential for use in patient-based simulations, is utilised to account for the effect of shear-dependent viscosity on the resulting haemodynamics and wall shear stress stimulation. Aside from the Newtonian model, the blood rheology is approximated by two non-Newtonian models in order to determine whether the choice of a viscosity model is important in simulations involving coronary circulation. A comprehensive analysis of obtained results demonstrated notable superiority of all lumped parameter models, especially in comparison to the constant outlet pressure, which regardless of bypass type gave overestimated and physiologically misleading results. In terms of rheology, it was noted that blood in undamaged coronary arteries behaves as a Newtonian fluid, whereas in vessels with atypical lumen geometry, such as that of anastomosis or stenosis, its shear-thinning behaviour should not be ignored.

Impact of ascending aorta replacement by graft on elastic properties of descending thoracic aorta evaluated by cardiac magnetic resonance imaging

OBJECTIVE

The aim of our study was to evaluate the impact of aortic root replacement by graft on the elastic properties of the descending thoracic aorta using cardiac magnetic resonance imaging (MRI) and automatic post-processing.

MATERIALS AND METHODS

Nineteen patients were operated for an aortic root aneurysm. Cardiac MRI was performed before and after surgery to measure aortic compliance. Images were acquired on a 1.5 T MRI with a conventional aortic MRI protocol plus one additional kinetic sequence orientated perpendicularly to the aorta at the level of pulmonary trunk. The contours of the ascending and descending aortas were detected automatically for each phase with homemade software.

RESULTS

Mean time between surgical procedure and earliest post-operative MRI was 18.2 ± 7.1 months. There was no significant difference between the pre- and earliest post-operative mean descending aorta areas and no significant modification in descending aortic compliance after aortic root replacement (1.43 ± 0.84 vs 1.37 ± 0.58 mm²/mmHg, p = 0.47). Pre- and post-operative systolic and diastolic blood pressure were similar. There was a significant decrease in ascending aortic compliance after surgery (2.52 ± 1.24 vs 0.91 ± 0.52 mm²/mmHg; p < 0.0001).

DISCUSSION

The aortic root replacement by graft was not associated with changes in elastic properties of the descending aorta at short term.

CLINICAL REGISTRATION NUMBER

NCT03817008.

Flow patterns through vascular graft models with and without cuffs

The shape of a bypass graft plays an important role on its efficacy. Here, we investigated flow through two vascular graft designs-with and without cuff at the anastomosis. We conducted Digital Particle Image Velocimetry (DPIV) measurements to obtain the flow field information through these vascular grafts. Two pulsatile flow waveforms corresponding to cardiac cycles during the rest and the excitation states, with 10% and without retrograde flow out the proximal end of the native artery were examined. In the absence of retrograde flow, the straight end-to-side graft showed recirculation and stagnation regions that lasted throughout the full cardiac cycle with the stagnation region more pronounced in the excitation state. The contoured end-to-side graft had stagnation region that lasted only for a portion of the cardiac cycle and was less pronounced. With 10% retrograde flow, extended stagnation regions under both rest and excitation states for both bypass grafts were eliminated. Our results show that bypass graft designers need to consider both the type of flow waveform and presence of retrograde flow when sculpting an optimal bypass graft geometry.

Radiation suppresses neointimal hyperplasia through affecting proliferation and apoptosis of vascular smooth muscle cells

PURPOSE

To study the effect of x-ray radiotherapy on vascular smooth muscle cells (VSMCs) and elucidate the mechanisms in preventing neointimal hyperplasia of prosthetic vascular grafts.

MATERIALS AND METHODS

In model I, twelve mongrel dogs underwent revascularization with prosthetic grafts and half the dogs underwent irradiation of the grafts at 28 Gy. In model II, human VSMCs (hVSMCs) were maintained and divided into six groups to which external radiation was applied at six different doses: 0 Gy, 2 Gy, 8 Gy, 16 Gy, 24 Gy and 30 Gy. In both models, specimens were harvested and examined by using morphological, immunological, cellular and molecular methods.

RESULTS

After irradiation, the neointima thickness was significantly lower in irradiated groups (p≤0.01). The radiotherapy could up-regulate p27^kip1, and down-regulate proliferating cell nuclear antigen (PCNA) and S phase kinase associated protein 2 (Skp2). X-ray irradiation inhibits the proliferation of hVSMCs via acting on G1/S phase of cell cycle. The apoptosis of hVSMCs increased significantly with dose and time. The expression of PCNA and Skp2 were decreased after a first increasing trend with dose, but had a significant negative correlation with time. The expression of p27^kip1 had a significant positive correlation with dose and time.

CONCLUSIONS

Postoperative external fractionated irradiation after prosthetic vessel replacement of the abdominal aorta suppressed the development of hyperplasia in the graft neointima in the short term. There was a prominent time- and dose-dependent inhibition of VSMC proliferation by radiation when it was administered.

Tetralogy of Fallot Surgical Repair: Shunt Configurations, Ductus Arteriosus and the Circle of Willis

In this study, hemodynamic performance of three novel shunt configurations that are considered for the surgical repair of tetralogy of Fallot (TOF) disease are investigated in detail. Clinical experience suggests that the shunt location, connecting angle, and its diameter can influence the post-operative physiology and the neurodevelopment of the neonatal patient. An experimentally validated second order computational fluid dynamics (CFD) solver and a parametric neonatal diseased great artery model that incorporates the ductus arteriosus (DA) and the full patient-specific circle of Willis (CoW) are employed. Standard truncated resistance CFD boundary conditions are compared with the full cerebral arterial system, which resulted 21, -13, and 37% difference in flow rate at the brachiocephalic, left carotid, and subclavian arteries, respectively. Flow splits at the aortic arch and cerebral arteries are calculated and found to change with shunt configuration significantly for TOF disease. The central direct shunt (direct shunt) has pulmonary flow 5% higher than central oblique shunt (oblique shunt) and 23% higher than modified Blalock Taussig shunt (RPA shunt) while the DA is closed. Maximum wall shear stress (WSS) in the direct shunt configuration is 9 and 60% higher than that of the oblique and RPA shunts, respectively. Patent DA, significantly eliminated the pulmonary flow control function of the shunt repair. These results suggests that, due to the higher flow rates at the pulmonary arteries, the direct shunt, rather than the central oblique, or right pulmonary artery shunts could be preferred by the surgeon. This extended model introduced new hemodynamic performance indices for the cerebral circulation that can correlate with the post-operative neurodevelopment quality of the patient.

Mathematical Analysis and Physical Profile of Blalock-Taussig Shunt and Sano Modification Procedure in Hypoplastic Left Heart Syndrome: Review of the Literature and Implications for the Anesthesiologist

The first stage of surgical treatment for hypoplastic left heart syndrome (HLHS) includes the creation of artificial systemic-to-pulmonary connections to provide pulmonary blood flow. The modified Blalock-Taussig (mBT) shunt has been the technique of choice for this procedure; however, a right ventricle-pulmonary artery (RV-PA) shunt has been introduced into clinical practice with encouraging but still conflicting outcomes when compared with the mBT shunt. The aim of this study is to explore mathematical modeling as a tool for describing physical profiles that could assist the surgical team in predicting complications related to stenosis and malfunction of grafts in an attempt to find correlations with clinical outcomes from clinical studies that compared both surgical techniques and to assist the anesthesiologist in making decisions to manage patients with this complex cardiac anatomy. Mathematical modeling to display the physical characteristics of the chosen surgical shunt is a valuable tool to predict flow patterns, shear stress, and rate distribution as well as energetic performance at the graft level and relative to ventricular efficiency. Such predictions will enable the surgical team to refine the technique so that hemodynamic complications be anticipated and prevented, and are also important for perioperative management by the anesthesia team.

Compliance mismatch and compressive wall stresses drive anomalous remodelling of pulmonary trunks reinforced with Dacron grafts

Synthetic grafts are often satisfactory employed in cardiac and vascular surgery, including expanded poly(ethylene terephthalate) or expanded poly(tetrafluoroethylene). However, accumulating evidences suggest the emergence of worrisome issues concerning the long-term fate of prosthetic grafts as large vessel replacement. Disadvantages related to the use of synthetic grafts can be traced in their inability of mimicking the elasto-mechanical characteristics of the native vascular tissue, local suture overstress leading to several prosthesis-related complications and retrograde deleterious effects on valve competence, cardiac function and perfusion. Motivated by this, in the present work it is analyzed - by means of both elemental biomechanical paradigms and more accurate in silico Finite Element simulations - the physical interaction among aorta, autograft and widely adopted synthetic (Dacron) prostheses utilized in transposition of pulmonary artery, highlighting the crucial role played by somehow unexpected stress fields kindled in the vessel walls and around suture regions, which could be traced as prodromal to the triggering of anomalous remodelling processes and alterations of needed surgical outcomes. Theoretical results are finally compared with histological and surgical data related to a significant experimental animal campaign conducted by performing pulmonary artery transpositions in 30 two-month old growing lambs, followed up during growth for six months. The in vivo observations demonstrate the effectiveness of the proposed biomechanical hypothesis and open the way for possible engineering-guided strategies to support and optimize surgical procedures.

Old Myths, New Concerns: the Long-Term Effects of Ascending Aorta Replacement with Dacron Grafts. Not All That Glitters Is Gold

Synthetic grafts are widely used in cardiac and vascular surgery since the mid-1970s. Despite their general good performance, inability of mimicking the elastomechanical characteristics of the native arterial tissue, and the consequent lack of adequate compliance, leads to a cascade of hemodynamic and biological alterations deeply affecting cardiovascular homeostasis. Those concerns have been reconsidered in more contemporaneous surgical and experimental reports which also triggered some research efforts in the tissue engineering field towards the realization of biomimetic arterial surrogates. The present review focuses on the significance of the “compliance mismatch” phenomenon occurring after aortic root or ascending aorta replacement with prosthetic grafts and discusses the clinical reflexes of this state of tissue incompatibility, as the loss of the native elastomechanical properties of the aorta can translate into detrimental effects on the normal efficiency of the aortic root complex with impact in the long-term results of patients undergoing aortic replacement.

Numerical simulation of compliant artery bypass grafts using fluid-structure interaction framework

Early researches on the artery bypass graft (ABG) generally took the assumption of rigid vessel wall that ignored the wall compliancy. To obtain more realistic and physiological hemodynamic parameters, a fluid structure interaction study on a complete ABG was carried out. It was concluded: (1) a compliant vessel is able to expand its vessel diameter and decrease its anastomosis angle to achieve a buffer for the blood, thereby helping to reduce endothelial cell injury. (2) The vessel walls experienced their maximum deformation at the time of peak pressure while the deformation could be ignored during diastole. However, the consideration of wall compliance did not quantitatively change the flow characters compared to those of rigid walls. (3) Generally, the hemodynamic priority of helical-type ABG over a conventional one was further strengthened by adopting compliant vessel wall. (4) The consideration of the wall deformation revealed a hidden fact by the rigid wall assumption: Helical ABG aggravated the risk of intimal hyperplasia at its toe region due to its geometry and flow asymmetry. The present study may be useful for surgeons and graft designers to optimize the current and future ABG configurations and selection of materials.

Analytical Side-to-Side Related Anastomotic Strategies and Artery Patching

Suture line stress concentration and intimal hyperplasia are related to the long-term complications of end-toside and side-to-side anastomosis. Several factors, such as hemodynamic effects, biological activities and the mechanical properties of the blood vessels, are identified to influence the problem. Yet, it is not completely clear which are the factors that influence most the long-term complications and in what specific way. This study aims to examine if elastic (compliance) mismatch increases the stress concentration and intimal thickening at the suture line. Better compliance may be obtained by using grafts with similar mechanical properties to the host artery or by anastomosis techniques that utilize vein patches and cuffs (Taylor-patch and Miller-cuff anastomosis). The anastomosis model used in this study is a circular cylindrical system consisting of two semi-cylinders, interconnected by two hinges. The internal blood pressure is applied on the arterial walls. The static and dynamic responses are analytically derived in terms of radial and tangential displacements, internal forces and strains of the two blood vessels and rotation of their cross-section. Results suggest that increased elastic mismatch between the artery and the graft may promote elevated intimal thickening due to large incompatible angles at the junction, whereas there is no correlation between elastic mismatch and elevated stress concentration at the suture line. Another interesting application of the present model is the patching of arteries as applied in carotid endarterectomy.

Biomechanical rationale of coronary artery bypass grafting of multivessel disease

The biomechanical model of human coronary arteries was modified for improving the quality of diagnosis and surgical treatment for coronary heart disease. The problem of hemodynamics in the left coronary artery with multivessel bed disease - 45% stenosis of the anterior descending branch and 75% stenosis of the circumflex branch - was particularly considered. Numerical simulation of the coronary arterial bypass of the main trunk was carried out to estimate the functional condition of the coronary arteries after restoring myocardial blood supply by surgery.

Numerical investigation of blood flow in a deformable coronary bifurcation and non-planar branch

INTRODUCTION

Among cardiovascular diseases, arterials stenosis is recognized more commonly than the others. Hemodynamic characteristics of blood play a key role in the incidence of stenosis. This paper numerically investigates the pulsatile blood flow in a coronary bifurcation with a non-planar branch. To create a more realistic analysis, the wall is assumed to be compliant. Furthermore, the flow is considered to be three-dimensional, incompressible, and laminar.

METHODS

The effects of non-Newtonian blood, compliant walls and different angles of bifurcation on hemodynamic characteristics of flow were evaluated. Shear thinning of blood was simulated with the Carreau-Yasuda model. The current research was mainly focused on the flow characteristics in bifurcations since atherosclerosis occurs mostly in bifurcations. Moreover, as the areas with low shear stresses are prone to stenosis, these areas were identified.

RESULTS

Our findings indicated that the compliant model of the wall, bifurcation's angle, and other physical properties of flow have an impact on hemodynamics of blood flow. Lower wall shear stress was observed in the compliant wall than that in the rigid wall. The outer wall of bifurcation in all models had lower wall shear stress. In bifurcations with larger angles, wall shear stress was higher in outer walls, and lower in inner walls.

CONCLUSION

The non-Newtonian blood vessels and different angles of bifurcation on hemodynamic characteristics of flow evaluation confirmed a lower wall shear stress in the compliant wall than that in the rigid wall, while the wall shear stress was higher in outer walls but lower in inner walls in the bifurcation regions with larger angles.

Dynamic behavior of suture-anastomosed arteries and implications to vascular surgery operations

BACKGROUND

Routine vascular surgery operations involve stitching of disconnected human arteries with themselves or with artificial grafts (arterial anastomosis). This study aims to extend current knowledge and provide better-substantiated understanding of the mechanics of end-to-end anastomosis through the development of an analytical model governing the dynamic behavior of the anastomotic region of two initially separated arteries.

METHODS

The formulation accounts for the arterial axial-circumferential deformation coupling and suture-artery interaction. The proposed model captures the effects of the most important parameters, including the geometric and mechanical properties of artery and sutures, number of sutures, loading characteristics, longitudinal residual stresses, and suture pre-tensioning.

RESULTS

Closed-form expressions are derived for the system response in terms of arterial radial displacement, anastomotic gap, suture tensile force, and embedding stress due to suture-artery contact interaction. Explicit objective functionalities are established to prevent failure at the anastomotic interface.

CONCLUSIONS

The mathematical formulation reveals useful interrelations among the problem parameters, thus making the proposed model a valuable tool for the optimal selection of materials and improved functionality of the sutures. By virtue of their generality and directness of application, the findings of this study can ultimately form the basis for the development of vascular anastomosis guidelines pertaining to the prevention of post-surgery implications.

A computational fluid dynamics study on hemodynamics for different locations of the distal anastomosis of a bypass nearby a collateral vessel in the femoropopliteal area

Revascularization of the femoropopliteal sector is often performed by the placement of a bypass. In this paper, we have studied the effects of hemodynamics on patency of the bypass for different positions of the distal anastomosis close to a collateral artery. Computational fluid dynamics (CFD) are used for this study. The cardiac cycle-averaged wall shear stress (WSS) and oscillation index (OSI) have been analyzed. Low WSS and high OSI may increase the risk of intimal hyperplasia (IH), which may reduce bypass patency. From the CFD simulations, spots of low WSS and high OSI are found within and near the entrance of the collateral artery, near the suture line, at the floor, toe, and heel. We regarded flow ratios of 20:80 and of 35:65. It is found that for the high flow ratio anastomosis located proximal to the collateral artery is clearly more advantageous. However for the low flow ratio anastomosis located distal to the collateral artery seems to be slightly more advantageous, the results are less conclusive. One of the studied flow geometries has been validated by in vitro experiments using a time resolved particle image velocimetry technique. Velocity fields from these experiments are in good agreement with the CFD results.

INTIMAL HYPERPLASIA AND WALL SHEAR IN ARTERIAL BYPASS Y-GRAFTING AND CONSEQUENCE GRAFTING: A NUMERICAL STUDY

The progression of intimal hyperplasia is considered to be the main cause of bypass failure and is directly related to the individual blood rheology, local arterial geometry and placement of the junctions, graft diameter and graft surface characteristics as well as the degree of compliance. In this paper we use commercial computational fluid dynamics (CFD) ANSYS to examine under the correct physiological flow conditions the hemodynamic forces of composite bypass with internal mammary artery in Y-grafting and consequence grafting which is known to achieve high patency rate and highly recommended by clinicians. Particular emphasis is given here on the parameters that could initiate the development of intimal hyperplasia within these bypass configurations. The hemodynamic flow patterns between the consequence grafting and the composite Y-grafting are observed here to be different. Moreover, on both end-to-side and side-to-side configurations, the circulating flows are detected in the vicinity of the junction area, while the Dean flow vortexes are only observed on the end-to-side configuration. Likewise, the hemodynamic flow on the end-to-side configuration on the LCX of both 45° and 90° Y-grafting is found to be smoother than that of the junction on the LCA, regardless of the changing of anastomosis angles. The high WSS gradients are observed at the vicinity of the toe and on the bed of the junction, while the low WSS are presented at the distal of the stenosis and at the stagnation point. The clinical relevance of the results are presented and discussed with particular focus on the factors and the flow patterns that trigger the development of intimal hyperplasia.

Coronary artery bypass grafting hemodynamics and anastomosis design: a biomedical engineering review

In this paper, coronary arterial bypass grafting hemodynamics and anastomosis designs are reviewed. The paper specifically addresses the biomechanical factors for enhancement of the patency of coronary artery bypass grafts (CABGs). Stenosis of distal anastomosis, caused by thrombosis and intimal hyperplasia (IH), is the major cause of failure of CABGs. Strong correlations have been established between the hemodynamics and vessel wall biomechanical factors and the initiation and development of IH and thrombus formation. Accordingly, several investigations have been conducted and numerous anastomotic geometries and devices have been designed to better regulate the blood flow fields and distribution of hemodynamic parameters and biomechanical factors at the distal anastomosis, in order to enhance the patency of CABGs. Enhancement of longevity and patency rate of CABGs can eliminate the need for re-operation and can significantly lower morbidity, and thereby reduces medical costs for patients suffering from coronary stenosis. This invited review focuses on various endeavors made thus far to design a patency-enhancing optimized anastomotic configuration for the distal junction of CABGs.

Numerical analysis of non-Newtonian blood flow and wall shear stress in realistic single, double and triple aorto-coronary bypasses

Considering the fact that hemodynamics plays an important role in the patency and overall performance of implanted bypass grafts, this work presents a numerical investigation of pulsatile non-Newtonian blood flow in three different patient-specific aorto-coronary bypasses. The three bypass models are distinguished from each other by the number of distal side-to-side and end-to-side anastomoses and denoted as single, double and triple bypasses. The mathematical model in the form of time-dependent nonlinear system of incompressible Navier-Stokes equations is coupled with the Carreau-Yasuda model describing the shear-thinning property of human blood and numerically solved using the principle of the SIMPLE algorithm and cell-centred finite volume method formulated for hybrid unstructured tetrahedral grids. The numerical results computed for non-Newtonian and Newtonian blood flow in the three aorto-coronary bypasses are compared and analysed with emphasis placed on the distribution of cycle-averaged wall shear stress and oscillatory shear index. As shown in this study, the non-Newtonian blood flow in all of the considered bypass models does not significantly differ from the Newtonian one. Our observations further suggest that, especially in the case of sequential grafts, the resulting flow field and shear stimulation are strongly influenced by the diameter of the vessels involved in the bypassing.

Granulocyte colony-stimulating factor minimizes negative remodeling of decellularized small diameter vascular graft conduits but not medial degeneration

BACKGROUND

Poor endothelialization and intimal hyperplasia are major causes of small diameter vascular conduit (SDVC) failure. The present study was aimed to investigate the influence of granulocyte colony-stimulating factor (G-CSF) on inhibiting adverse remodeling of decellularized SDVCs.

METHODS

Sprague-Dawley rats implanted with allograft infra renal abdominal aortic conduits were divided into 2 groups according to whether they were treated with G-CSF (+G-CSF group; n=6) or without (Decell group; n=6). The conduits were harvested at 8 weeks after surgery and examined for intimal hyperplasia, collagen deposition, and -actin-staining cells. The medial layer was also examined for signs of cellular repopulation and changes in the elastic fiber morphology.

RESULTS

Intergroup comparison of the intimal composition showed relatively sparse collagen content and predominance of -actin-staining cells in the +G-CSF group. The medial layer in the 2 groups showed similar degrees of elastic fiber degeneration and wall thinning relative to the normal aortic wall. However, the enhanced staining for von Willebrand factor and CD31, along with transmission electron microscopy findings of superior cellular and ultrastructural preservation, suggested that the remodeling and endothelialization in the +G-CSF conduits were superior to those in the Decell conduits.

CONCLUSIONS

This study suggests that G-CSF exerts a positive influence on inhibiting adverse vascular remodeling of decellularized vascular conduit implants. However, whether G-CSF administration may also effectuate an improved ability to preserve the medial structural integrity is unclear.

Numerical Simulation of Physiological Blood Flow in 2-way Coronary Artery Bypass Grafts

The Coronary Artery Bypass Graft (CABG) yields excellent results and remains the modern standard of care for treatment of occlusive disease in the cardiovascular system. However, the development of anastomotic Intimal Hyperplasia (IH) and restenosis can compromise the medium-and-long term effects of the CABG. This problem can be correlated with the geometric configuration and hemodynamics of the bypass graft. A novel geometric configuration was proposed for the CABG with two symmetrically implanted grafts for the purpose of improving the hemodynamics. Physiological blood flows in two models of bypass grafts were simulated using numerical methods. One model was for the conventional bypass configuration with a single graft (1-way model); the other model was for the proposed bypass configuration with two grafts (2-way model). The temporal and spatial distributions of hemodynamics, such as flow patterns and Wall Shear Stress (WSS) in the vicinity of the distal anastomoses, were analyzed and compared. Calculation results showed that the 2-way model possessed favorable hemodynamics with uniform longitudinal flow patterns and WSS distributions, which could decrease the probability of restenosis and improve the effect of the surgical treatment. Concerning the limitations of the 2-way bypass grafts, it is necessary to perform animal experiments to verify the viability of this novel idea for the CABG.

Numerical analysis of coronary artery bypass grafts: an over view

Arterial bypass grafts tend to fail after some years due to the development of intimal thickening (restenosis). Non-uniform hemodynamics following a bypass operation contributes to restenosis and bypass failure can occur due to the focal development of anastomotic intimal hyperplasia. Additionally, surgical injury aggravated by compliance mismatch between the graft and artery has been suggested as an initiating factor for progress of wall thickening along the suture line Vascular grafts that are small in diameter tend to occlude rapidly. Computational fluid dynamics (CFD) methods have been effectively used to simulate the physical and geometrical parameters characterizing the hemodynamics of various arteries and bypass configurations. The effects of such changes on the pressure and flow characteristics as well as the wall shear stress during a cardiac cycle can be simulated. Recently, utilization of fluid and structure interactions have been used to determine fluid flow parameters and structure forces including stress and strains relationships under steady and transient conditions. In parallel to this, experimental diagnostics techniques such as Laser Doppler Anemometry, Particle Image Velocimetry, Doppler Guide wire and Magnetic Resonance Imaging have been used to provide essential information and to validate the numerical results. Moreover, clinical imaging techniques such as magnetic resonance or computed tomography have assisted considerably in gaining a detailed patient-specific picture of the blood flow and structure dynamics. This paper gives a review of recent numerical investigations of various configurations of coronary artery bypass grafts (CABG). In addition, the paper ends with a summary of the findings and the future directions.

Interposition vein cuff for infragenicular prosthetic bypass graft

BACKGROUND

The use of prosthetic grafts such as polytetrafluorethylene (PTFE) or Dacron to bypass occluded arteries in the lower leg is an accepted practice in the absence of suitable autologous vein. The aim is limb salvage or functional improvement in critical limb ischaemia, but patency rates for below knee prosthetic bypasses are low. Creating a vein cuff at the distal anastomosis is thought to improve outcomes. Other techniques including the use of pre-cuffed synthetic grafts, spliced segments of vein and the creation of an arterio-venous fistula (AVF) are also used to improve patency.

OBJECTIVES

To compare the beneficial effects of using vein cuffed prosthetic grafts for below knee bypass in critical limb ischaemia with other types of reconstruction.

SEARCH METHODS

The Cochrane Peripheral Vascular Diseases Group Trials Search Co-ordinator searched the Specialised Register (last searched May 2012) and CENTRAL (2012, Issue 5) for publications comparing prosthetic infragenicular bypass using vein cuffs with other bypass techniques.

SELECTION CRITERIA

Randomised controlled trials comparing interposition vein cuff prosthetic graft with autologous vein graft and non-cuffed prosthetic graft for infragenicular bypass in patients with critical limb ischaemia were included. Trials comparing vein cuff prosthetic grafts with or without AVF and vein cuff prosthetic grafts with pre-cuffed prosthetic grafts were also included.

DATA COLLECTION AND ANALYSIS

The trials were selected and assessed independently by two review authors.

MAIN RESULTS

Six trials with a combined total of 885 patients were included in this review. Only studies using prosthetic PTFE grafts were identified.Two trials compared PTFE graft with or without a vein cuff. In one underpowered trial for below knee bypass the cumulative primary patency rate was statistically significantly higher in the vein cuff group (80.3% versus 65.3% at 12 months and 51.8% versus 29.1% at 24 months, P = 0.03). There was no statistically significant difference in secondary patency (82.9% versus 72.5% and 58.6% versus 34.9%, P = 0.14) and limb salvage rates (86.3% versus 71.8% and 82.6% versus 62.2%, P = 0.08) at 12 and 24 months respectively. The other trial showed no statistically significant difference between the groups at three years in the below knee femoro-popliteal bypasses (primary patency rate 26% (95% confidence interval (CI) 18 to 38) and 43% (95% CI 33 to 58), secondary patency rate 32% (95% CI 23 to 44) and 42% (95% CI 31 to 56) and limb salvage rate 64% (95% CI 54 to 75) and 61% (95% CI 50 to 74) in the collar and no collar groups respectively). In the femoro-distal bypass group, the differences in primary patency, secondary patency and limb salvage rates were also not statistically significant at three years (primary patency rate 20% (95% CI 11 to 38) and 17% (95% CI 9 to 33), secondary patency rate 22% (95% CI 12 to 39) and 20% (95% CI 11 to 35) and limb salvage rate 59% (95% CI 46 to 76) and 44% (95% CI 32 to 61) in the collar and no collar groups respectively).One trial compared pre-cuffed PTFE grafts with vein cuffed grafts. There was no statistically significant difference in primary patency rate (62% pre-cuffed PTFE versus 52% vein cuff PTFE and 49% versus 44%, P = 0.53), secondary patency rate (66% pre-cuffed PTFE versus 53% vein cuff PTFE and 55% versus 50%, P = 0.30) or limb salvage rate (75% pre-cuffed PTFE versus 72% vein cuff PTFE and 62% versus 65%, P = 0.88) at 12 and 24 months respectively.One trial compared spliced vein grafts with vein cuffed PTFE grafts. At 24 months, the secondary patency rate was statistically significantly higher in the spliced vein group (86% in the spliced vein and 52% in the vein cuff group, P < 0.05). There was no statistical significant difference in primary patency rate (44% versus 50%, P > 0.05) and limb salvage rate (94% versus 85%, P > 0.05).Two trials compared vein cuff PTFE grafts with and without AVF. There was no statistical significant difference at 24 months in primary patency rate (29% versus 36%, P = 0.77; 32% versus 28%, P = 0.2), secondary patency rate (40% versus 40%, P = 0.89; 28% versus 24%, P = 0.2) and limb salvage rate (65% versus 70%, P = 0.97; 62% versus 71%, P = 0.3).

AUTHORS' CONCLUSIONS

There is evidence that a vein cuff at the distal anastomosis site improves primary graft patency rates for below knee PTFE graft, but this does not reduce the risk of limb loss. Pre-cuffed PTFE grafts have comparable patency and limb salvage rates to vein cuff PTFE grafts. The use of spliced veins improved secondary patency but this did not translate into improved limb salvage. The use of an AVF alone showed no added benefits. Evidence for a beneficial effect of vein cuffed PTFE grafts is weak and based on underpowered trials. A large study with a specific focus on below knee vein cuff prosthetic grafts, including PTFE, is required.

CABG MODELS FLOW SIMULATION STUDY ON THE EFFECTS OF VALVE REMNANTS IN THE VENOUS GRAFT

Venous valves and sinuses are frequently observed in vein grafts in the coronary artery bypass grafts (CABG). However, from the biomedical engineering viewpoint, vein grafts are always assumed as smooth tubes in the existing simulations, and no effort has been made to investigate the effects of jaggedness of the graft inner wall due to the valve cusps remnants and valve sinus (in case of valve-stripped saphenous vein (SV) grafts) on the blood flow patterns and hemodynamic parameters (HPs). In this paper, the effects of the inner surface irregularities of a vein graft on the blood flow is investigated in the graft as well as in the distal anastomotic region, with a more realistic geometry of valve-stripped SV, by means of numerical simulation of pulsatile, Newtonian blood flow. The simulation results demonstrate that the valve remnants and sinuses cause disturbances in the flow field within the graft (due to vortices formation within the valve sinuses) and undesirable distribution of HPs, which can result in early atherosclerotic lesion development in the graft.

ASSESSING HEMODYNAMIC PERFORMANCES OF SMALL DIAMETER HELICAL GRAFTS: TRANSIENT SIMULATION

The present study numerically simulated the physiological pulsatile flow in helical grafts to increase understanding of its flow mechanism which may contribute to the design of better grafts. The wall-indices like time-averaged wall shear stress (WSS) and oscillatory shear index (OSI), joint with a quantitative index for helical flow by means of Lagrangian approach, were introduced as effective instruments to classify the hemodynamic performance of helical grafts. The simulation suggests that the helical geometry created amplified WSS magnitudes as well as elevated velocities near the wall. The calculated oscillatory shear index (OSI) values were never exceeded to 0.07 which is not considered physiologically significant. In addition, the strong secondary flow in helical graft helped the flow mixing between low-momentum fluid closer to the surface and high-momentum fluid at the center which brought the high-momentum fluid to the surface. Furthermore, Helicity analysis revealed that most of the fluid particles experienced counter-clockwise rotation during the whole cardiac cycle which helps to protect the graft wall from damage by reducing the laterally directed forces and keep flow stability. It concluded that a helical graft provides guaranties for the graft wall surface to get smooth and even washing by the blood and eliminates mechanical trauma to blood cells so that atherosclerotic plaques can hardly form in the graft wall.

Influences of Geometric Configurations of Bypass Grafts on Hemodynamics in End-to-Side Anastomosis

Background

Although considerable efforts have been made to improve the graft patency in coronary artery bypass surgery, the role of biomechanical factors remains underrecognized. The aim of this study is to investigate the influences of geometric configurations of the bypass graft on hemodynamic characteristics in relation to anastomosis.

Materials and Methods

The Numerical analysis focuses on understanding the flow patterns for different values of inlet and distal diameters and graft angles. The Blood flow field is treated as a two-dimensional incompressible laminar flow. A finite volume method is adopted for discretization of the governing equations. The Carreau model is employed as a constitutive equation for blood. In an attempt to obtain the optimal aorto-coronary bypass conditions, the blood flow characteristics are analyzed using in vitro models of the end-to-side anastomotic angles of 45°, 60° and 90°. To find the optimal graft configurations, the mass flow rates at the outlets of the four models are compared quantitatively.

Results

This study finds that Model 3, whose bypass diameter is the same as the inlet diameter of the stenosed coronary artery, delivers the largest amount of blood and the least pressure drop along the arteries.

Conclusion

Biomechanical factors are speculated to contribute to the graft patency in coronary artery bypass grafting.

Compliant model of a coupled sequential coronary arterial bypass graft: effects of vessel wall elasticity and non-Newtonian rheology on blood flow regime and hemodynamic parameters distribution

We have recently developed a novel design for coronary arterial bypass surgical grafting, consisting of coupled sequential side-to-side and end-to-side anastomoses. This design has been shown to have beneficial blood flow patterns and wall shear stress distributions which may improve the patency of the CABG, as compared to the conventional end-to-side anastomosis. In our preliminary computational simulation of blood flow of this coupled sequential anastomoses design, the graft and the artery were adopted to be rigid vessels and the blood was assumed to be a Newtonian fluid. Therefore, the present study has been carried out in order to (i) investigate the effects of wall compliance and non-Newtonian rheology on the local flow field and hemodynamic parameters distribution, and (ii) verify the advantages of the CABG coupled sequential anastomoses design over the conventional end-to-side configuration in a more realistic bio-mechanical condition. For this purpose, a two-way fluid-structure interaction analysis has been carried out. A finite volume method is applied to solve the three-dimensional, time-dependent, laminar flow of the incompressible, non-Newtonian fluid; the vessel wall is modeled as a linearly elastic, geometrically non-linear shell structure. In an iteratively coupled approach the transient shell equations and the governing fluid equations are solved numerically. The simulation results indicate a diameter variation ratio of up to 4% and 5% in the graft and the coronary artery, respectively. The velocity patterns and qualitative distribution of wall shear stress parameters in the distensible model do not change significantly compared to the rigid-wall model, despite quite large side-wall deformations in the anastomotic regions. However, less flow separation and reversed flow is observed in the distensible models. The wall compliance reduces the time-averaged wall shear stress up to 32% (on the heel of the conventional end-to-side model) and somewhat increases the oscillatory nature of the flow. It is found that the effects of wall compliance and non-Newtonian rheology are not independent, and they interact with each other. In spite of the modest influence of wall compliance and non-Newtonian rheology on the hemodynamic parameters distribution, the inclusion of these properties has unveiled further advantages of the coupled sequential anastomoses model over the conventional end-to-side anastomosis which had not been revealed in the previous study with the rigid-wall and Newtonian fluid models. Hence, the inclusion of wall compliance and non-Newtonian rheology in flow simulation of blood vessels can be essential in quantitative and comparative investigations.

A stochastic collocation method for uncertainty quantification and propagation in cardiovascular simulations

Simulations of blood flow in both healthy and diseased vascular models can be used to compute a range of hemodynamic parameters including velocities, time varying wall shear stress, pressure drops, and energy losses. The confidence in the data output from cardiovascular simulations depends directly on our level of certainty in simulation input parameters. In this work, we develop a general set of tools to evaluate the sensitivity of output parameters to input uncertainties in cardiovascular simulations. Uncertainties can arise from boundary conditions, geometrical parameters, or clinical data. These uncertainties result in a range of possible outputs which are quantified using probability density functions (PDFs). The objective is to systemically model the input uncertainties and quantify the confidence in the output of hemodynamic simulations. Input uncertainties are quantified and mapped to the stochastic space using the stochastic collocation technique. We develop an adaptive collocation algorithm for Gauss-Lobatto-Chebyshev grid points that significantly reduces computational cost. This analysis is performed on two idealized problems--an abdominal aortic aneurysm and a carotid artery bifurcation, and one patient specific problem--a Fontan procedure for congenital heart defects. In each case, relevant hemodynamic features are extracted and their uncertainty is quantified. Uncertainty quantification of the hemodynamic simulations is done using (a) stochastic space representations, (b) PDFs, and (c) the confidence intervals for a specified level of confidence in each problem.

Characterization of vascular strain during in-vitro angioplasty with high-resolution ultrasound speckle tracking

Background

Ultrasound elasticity imaging provides biomechanical and elastic properties of vascular tissue, with the potential to distinguish between tissue motion and tissue strain. To validate the ability of ultrasound elasticity imaging to predict structurally defined physical changes in tissue, strain measurement patterns during angioplasty in four bovine carotid artery pathology samples were compared to the measured physical characteristics of the tissue specimens.

Methods

Using computational image-processing techniques, the circumferences of each bovine artery specimen were obtained from ultrasound and pathologic data.

Results

Ultrasound-strain-based and pathology-based arterial circumference measurements were correlated with an R² value of 0.94 (p = 0.03). The experimental elasticity imaging results confirmed the onset of deformation of an angioplasty procedure by indicating a consistent inflection point where vessel fibers were fully unfolded and vessel wall strain initiated.

Conclusion

These results validate the ability of ultrasound elasticity imaging to measure localized mechanical changes in vascular tissue.

Flow interactions with cells and tissues: cardiovascular flows and fluid-structure interactions. Sixth International Bio-Fluid Mechanics Symposium and Workshop, March 28-30, 2008, Pasadena, California

Interactions between flow and biological cells and tissues are intrinsic to the circulatory, respiratory, digestive and genitourinary systems. In the circulatory system, an understanding of the complex interaction between the arterial wall (a living multi-component organ with anisotropic, nonlinear material properties) and blood (a shear-thinning fluid with 45% by volume consisting of red blood cells, platelets, and white blood cells) is vital to our understanding of the physiology of the human circulation and the etiology and development of arterial diseases, and to the design and development of prosthetic implants and tissue-engineered substitutes. Similarly, an understanding of the complex dynamics of flow past native human heart valves and the effect of that flow on the valvular tissue is necessary to elucidate the etiology of valvular diseases and in the design and development of valve replacements. In this paper we address the influence of biomechanical factors on the arterial circulation. The first part presents our current understanding of the impact of blood flow on the arterial wall at the cellular level and the relationship between flow-induced stresses and the etiology of atherosclerosis. The second part describes recent advances in the application of fluid-structure interaction analysis to arterial flows and the dynamics of heart valves.

Mechano-sensitive transcriptional factor Egr-1 regulates insulin-like growth factor-1 receptor expression and contributes to neointima formation in vein grafts

OBJECTIVE

Vein grafts in a coronary bypass or a hemodialysis access often develop obliterative growth of the neointima. We previously reported that the mechanical stretch-activated insulin-like growth factor-1 receptor (IGF-1/IGF-1R) pathway plays an important role in this remodeling. However, the transcriptional mechanism(s) regulating IGF-1R expression and neointima formation have not been identified.

METHODS AND RESULTS

Deletion and site-specific mutagenesis analysis of IGF-1R promoter identified that the minimal mechano-responsive promoter element (-270--130) contains 2 consensus sequences for binding of early growth reponse-1 (Egr-1) transcriptional factor. Mechanical stretch stimulated both Egr-1 mRNA (4.6-fold) and protein (5.2-fold) in vascular smooth muscle cells. Interposition of a vein into an artery increased Egr-1 mRNA (7.8+/-2.6-fold vs sham). In vascular smooth muscle cells isolated from Egr-1 knockout mice, mechanical stretch could not increase IGF-1R, and vascular smooth muscle cells proliferation was decreased by 47% compared to wild-type cells. Importantly, the neointima area was reduced by at least 50%, and the lumen-to-media ratio increased by 55% in vein grafts of Egr-1 knockout mice compared with results of wild-type mice.

CONCLUSIONS

Egr-1 is a mechano-sensitive transcriptional factor that stimulates IGF-1R transcription, resulting in vascular remodeling of vein grafts.

Recent advances in the application of computational mechanics to the diagnosis and treatment of cardiovascular disease

During the last 30 years, research into the pathogenesis and progression of cardiovascular disease has had to employ a multidisciplinary approach involving a wide range of subject areas, from molecular and cell biology to computational mechanics and experimental solid and fluid mechanics. In general, research was driven by the need to provide answers to questions of critical importance for disease management. Ongoing improvements in the spatial resolution of medical imaging equipment coupled to an exponential growth in the capacity, flexibility and speed of computational techniques have provided a valuable opportunity for numerical simulations and complex experimental techniques to make a contribution to improving the diagnosis and clinical management of many forms of cardiovascular disease. This paper contains a review of recent progress in the numerical simulation of cardiovascular mechanics, focusing on three particular areas: patient-specific modeling and the optimization of surgery in pediatric cardiology, evaluating the risk of rupture in aortic aneurysms, and noninvasive characterization of intraventricular flow in the management of heart failure.

Haemodynamic analysis of coronary artery bypass grafting in a non-linear deformable artery and Newtonian pulsatile blood flow

A three-dimensional (3D) computational model of stenotic coronary artery bypass grafting (CABG) system with fluid—structure interaction (FSI) using realistic physiological conditions is introduced. Unsteady pulsatile blood flow is applied to the wall of non-linear deformable arteries over the systolic period. In the analysis, the arbitrarily Lagrangian—Eulerian (ALE) formulation is used to couple the fluid region and solid domain. The method couples the equations of the deformation of the artery wall and applies them as the fluid domain boundary condition. The flow distribution and haemodynamic forces are presented in terms of velocity profiles and temporal and spatial wall shear stresses (WSSs) at the distal area. Rapid changes in the flow fields are observed in the early stages of the cardiac cycle, which alters the location of the recirculation zone from the toe to the host bed and then to the heel. The migration of the recirculation zone, considering the effect of deformability of the artery wall, indicates the same trend as the rigid wall model according to the location of low and high WSSs. However, the WSSs in the critical areas such as toe, heel, and suture lines are found to have dramatic drops in magnitudes in comparison with those of the rigid wall model. This could initiate the promotion of intimal hyperplasia (IH) and may cause an early graft failure in CABG.

Neonatal Aortic Arch Hemodynamics and Perfusion During Cardiopulmonary Bypass

The objective of this study is to quantify the detailed three-dimensional (3D) pulsatile hemodynamics, mechanical loading, and perfusion characteristics of a patient-specific neonatal aortic arch during cardiopulmonary bypass (CPB). The 3D cardiac magnetic resonance imaging (MRI) reconstruction of a pediatric patient with a normal aortic arch is modified based on clinical literature to represent the neonatal morphology and flow conditions. The anatomical dimensions are verified from several literature sources. The CPB is created virtually in the computer by clamping the ascending aorta and inserting the computer-aided design model of the 10 Fr tapered generic cannula. Pulsatile (130 bpm) 3D blood flow velocities and pressures are computed using the commercial computational fluid dynamics (CFD) software. Second order accurate CFD settings are validated against particle image velocimetry experiments in an earlier study with a complex cardiovascular unsteady benchmark. CFD results in this manuscript are further compared with the in vivo physiological CPB pressure waveforms and demonstrated excellent agreement. Cannula inlet flow waveforms are measured from in vivo PC-MRI and 3 kg piglet neonatal animal model physiological experiments, distributed equally between the head-neck vessels and the descending aorta. Neonatal 3D aortic hemodynamics is also compared with that of the pediatric and fetal aortic stages. Detailed 3D flow fields, blood damage, wall shear stress (WSS), pressure drop, perfusion, and hemodynamic parameters describing the pulsatile energetics are calculated for both the physiological neonatal aorta and for the CPB aorta assembly. The primary flow structure is the high-speed canulla jet flow (∼3.0 m/s at peak flow), which eventually stagnates at the anterior aortic arch wall and low velocity flow in the cross-clamp pouch. These structures contributed to the reduced flow pulsatility (85%), increased WSS (50%), power loss (28%), and blood damage (288%), compared with normal neonatal aortic physiology. These drastic hemodynamic differences and associated intense biophysical loading of the pathological CPB configuration necessitate urgent bioengineering improvements—in hardware design, perfusion flow waveform, and configuration. This study serves to document the baseline condition, while the methodology presented can be utilized in preliminary CPB cannula design and in optimization studies reducing animal experiments. Coupled to a lumped-parameter model the 3D hemodynamic characteristics will aid the surgical decision making process of the perfusion strategies in complex congenital heart surgeries.

A parametric numerical investigation on haemodynamics in distal coronary anastomoses

Anastomotic haemodynamics, which plays an important role in the performance of bypass graft, is known to be profoundly affected by the diameter ratio (Phi) and angle (alpha) between the graft and host artery in the peripheral region. We hypothesize that these geometric factors would play similar roles in distal coronary anastomoses and that they could be improved for clinical applications through parametric studies. Anastomotic models covering a range of Phi (1:1, 1.5:1 and 2:1) and alpha (15 degrees , 30 degrees , 45 degrees and 60 degrees ) were investigated numerically in physiological coronary flow conditions. The transient flow patterns, cycle-averaged wall shear stress (WSS), oscillatory shear index (OSI), spatial and temporal WSS gradients (SWSSG and TWSSG) were compared. Results show a stronger influence of Phi than alpha on haemodynamics in distal coronary artery anastomoses. Substantially higher SWSSG and TSSWG occur on the artery floor when Phi=1:1 compared to larger Phi. High levels of OSI occur in critical regions when Phi=1:1 and 2:1. The largest area of high OSI is found in the anastomotic region when alpha=15 degrees , whereas the highest level of SWSSG appears on the artery floor when alpha=60 degrees . The study suggests the clinical relevance of optimizing geometric parameters of coronary anastomoses to improve their haemodynamic performance. We speculate that for a distal coronary anastomosis with a 20:80 proximal-distal flow division ratio maintained in the host artery, Phi=1.5 and alpha=30-45 degrees would enhance its long-term performance.

Flow and wall shear stress in end-to-side and side-to-side anastomosis of venous coronary artery bypass grafts

PURPOSE

Coronary artery bypass graft (CABG) surgery represents the standard treatment of advanced coronary artery disease. Two major types of anastomosis exist to connect the graft to the coronary artery, i.e., by using an end-to-side or a side-to-side anastomosis. There is still controversy because of the differences in the patency rates of the two types of anastomosis. The purpose of this paper is to non-invasively quantify hemodynamic parameters, such as mass flow and wall shear stress (WSS), in end-to-side and side-to-side anastomoses of patients with CABG using computational fluid dynamics (CFD).

METHODS

One patient with saphenous CABG and end-to-side anastomosis and one patient with saphenous CABG and side-to-side anastomosis underwent 16-detector row computed tomography (CT). Geometric models of coronary arteries and bypasses were reconstructed for CFD analysis. Blood flow was considered pulsatile, laminar, incompressible and Newtonian. Peri-anastomotic mass flow and WSS were quantified and flow patterns visualized.

RESULTS

CFD analysis based on in-vivo CT coronary angiography data was feasible in both patients. For both types of CABG, flow patterns were characterized by a retrograde flow into the native coronary artery. WSS variations were found in both anastomoses types, with highest WSS values at the heel and lowest WSS values at the floor of the end-to-side anastomosis. In contrast, the highest WSS values of the side-to-side anastomosis configuration were found in stenotic vessel segments and not in the close vicinity of the anastomosis. Flow stagnation zones were found in end-to-side but not in side-to-side anastomosis, the latter also demonstrating a smoother stream division throughout the cardiac cycle.

CONCLUSION

CFD analysis of venous CABG based on in-vivo CT datasets in patients was feasible producing qualitative and quantitative information on mass flow and WSS. Differences were found between the two types of anastomosis warranting further systematic application of the presented methodology on multiple patient datasets.

Surgical Feasibility Study of a Novel Polytetrafluoroethylene Graft Design for the Treatment of Peripheral Arterial Disease

Disturbed flow patterns, material mismatch, and surgical injury are often cited as being significant contributors to failure at the distal end of femoropopliteal bypass grafts. The objective of this research is to propose a novel bypass graft design concept which seeks to reduce the incidence of disturbed flow in the bypass junction and to establish the surgical feasibility of the proposed device. A preliminary evaluation of the hemodynamic benefit associated with the proposed device was made using computational fluid dynamics. A prototype of the device was then constructed from commercially available materials, and it was prepared for implantation into the aorta of a pig. The computational model of the proposed device showed that significant flow correction was occurring in the in vitro model due to the geometric configuration of the design. The magnitude of the peak wall shear stress in the recirculation region was noted to decrease by 78%. Surgical feasibility of the proposed device was verified by successful implantation into the aorta of the pig. The pig was sacrificed after 7 weeks, the graft and host artery were excised, and histological examination downstream from the distal junction showed that intimal hyperplasia had developed in the host artery. The proposed device is surgically feasible and may offer a significant hemodynamic advantage over current graft designs.

A procedure to simulate coronary artery bypass graft surgery

In coronary artery bypass graft (CABG) surgery the involved tissues are overstretched, which may lead to intimal hyperplasia and graft failure. We propose a computational methodology for the simulation of traditional CABG surgery, and analyze the effect of two clinically relevant parameters on the artery and graft responses, i.e., incision length and insertion angle for a given graft diameter. The computational structural analyses are based on actual three-dimensional vessel dimensions of a human coronary artery and a human saphenous vein. The analyses consider the structure of the end-to-side anastomosis, the residual stresses and the typical anisotropic and nonlinear vessel behaviors. The coronary artery is modeled as a three-layer thick-walled tube. The finite element method is employed to predict deformation and stress distribution at various stages of CABG surgery. Small variations of the arterial incision have relatively big effects on the size of the arterial opening, which depends solely on the residual stress state. The incision length has a critical influence on the graft shape and the stress in the graft wall. Stresses at the heel region are higher than those at the toe region. The changes in the mechanical environment are severe along all transitions between the venous tissue and the host artery. Particular stress concentrations occur at the incision ends. The proposed computational methodology may be useful in designing a coronary anastomotic device for reducing surgical trauma. It may improve the quantitative knowledge of vessel diseases and serve as a tool for virtual planning of vascular surgery.