Liquid chromatography-electrospray ionization isotope dilution mass spectrometry analysis of paraquat and diquat using conventional and multilayer solid-phase extraction cartridges

Development of LC-MS/MS analytical method for the rapid determination of Diquat in water and beverages

This study aimed to develop simple, fast, and sensitive methods for the determination of diquat (DQ) in various matrices such as water and beverages. For water, direct injection was tested first, however, the sensitivity of the incurred samples were too low and couldn't possibly achieve the targeted limit of quantification. Hence, dilution with "weaker" injection solvents were tested, and the final conditions involved the dilution of water with acetonitrile (0.4 % ammonium hydroxide) which increased the sensitivity by more than ten times. Nevertheless, the beverages samples needed further treatment to achieve acceptable spiked recovery. The final conditions involved extraction using the aforementioned solvent, followed by heating and partitioning. Both of the methods satisfied the validation requirements, with an average recovery ranging from 85.9 to115 % and associated relative standard deviation (RSD %) within the range 3-8. Further applications on real samples were done to test the levels of contamination.

Simultaneous determination of water-soluble herbicides using hydrophilic interaction liquid chromatography-mass spectrometry

PURPOSE

The analysis of water-soluble herbicides, including glyphosate (Glyp), glufosinate (Gluf), paraquat (PQ), and diquat (DQ), is time-consuming and expensive because they cannot be analyzed using general toxicological screening methods. Thus, this study aimed to develop a simple and rapid method to simultaneously analyze these compounds without any derivatization nor ion-pairing reagents.

METHODS

The analytes were separated using hydrophilic interaction liquid chromatography and detected using tandem mass spectrometry. The developed method was applied to plant and biological samples assuming criminal damage and poisoning cases, respectively.

RESULTS

All analytes were separated well and detected with good peak shapes. For plant samples, the herbicides were specifically detected from withered leaves using a simple extraction method. For biological samples, quantitative analysis was successfully validated, and the limit of quantification values of Glyp and Gluf were 0.2 µg/mL, and those of PQ and DQ were 1 ng/mL.

CONCLUSION

The developed method had sufficient performance for practical forensic applications including poisoning cases and malicious uses to damage commercial crops.

HPLC-MS/MS determination and the postmortem distribution or postmortem redistribution of paraquat and its metabolites in four fatal intoxication cases

HPLC-MS/MS analysis and postmortem distribution or postmortem redistribution of paraquat and its two metabolites in poisoning death cases were reported. Paraquat, monoquat, and paraquat monopyridone were extracted from the sample with acetonitrile or methanol, respectively, detected by ZORBAX HILIC Plus (4.6 × 100 mm, 3.5 μm) chromatographic column, with 0.1 % formic acid aqueous solution - 0.1 % formic acid acetonitrile solution (v/v) as mobile phase. Paraquat, monoquat, and paraquat monopyridone had a good linear relationship within the range of 10-1000, 1-400, and 1-1000 ng/mL (or g), the correlation coefficient (r) were all ≥ 0.9996. Their detection limits were lower than 1 ng/mL (or g). The detection accuracy was 91.25∼113.44 %. The intra-day and inter-day precision were 1.51-3.99 % and 1.92-4.93 %, respectively. This method was used to detect and analyze four rare paraquat poisoning cases. The distribution of paraquat, monoquat, and paraquat monopyridone is uneven, which is relatively high in the heart, blood, lung, and kidney. Heart blood/Peripheral blood ratio of paraquat, monoquat, paraquat monopyridone concentration in two poisoned cases were 1.4, 2.0, 1.5 and 1.9, 1.3, 1.2, which showed a location dependent postmortem redistribution. This is the first time that HPLC-MS/MS and the postmortem distribution or postmortem redistribution of paraquat metabolites in poisoned death cases have been reported. This research provides scientific basis for forensic identification of paraquat poisoning cases and extraction of biological specimen.

Cucurbit[7]uril as a matrix solid-phase dispersion for the extraction of quaternary ammonium pesticides from vegetables and their determination using HPLC-UV

Cucurbit[7]uril (Q[7]) was first used as a dispersant sorbent material in a matrix solid-phase dispersion for the simultaneous extraction of four quaternary ammonium pesticides from vegetables before analysis using high-performance liquid chromatography with UV detection. Q[7] exhibited a better selectivity and adsorption capability for these compounds, which is due to its ability to bind selectively organic molecules into its hydrophobic cavity and to form stable host-guest inclusion complexes. Various parameters affecting the extraction were investigated and optimized, such as sorbent/sample mass ratio, grinding time, rinsing and eluting conditions. Under optimized conditions, the proposed method exhibited a linear response in the concentration range of 1-100 μg·kg^-1, satisfactory recoveries for eight types of vegetable samples (>70%), and high repeatability (RSD < 9.0%). The limits of quantification were between 0.43 μg·kg^-1 and 0.99 μg·kg^-1, which is nearly 50 times lower than the maximum residue limits established by the European Council.

Modified Screen-Printed Potentiometric Sensors based on Man-Tailored Biomimetics for Diquat Herbicide Determination

Screen-printed platforms integrated with molecularly imprinted polymers (MIP) were fabricated and characterized as potentiometric sensors for diquat (DQ). The synthesized MIP beads were studied as sensory carriers in plasticized poly(vinyl chloride) membranes. The sensors were constructed by using poly(3,4-ethylenedioxythiophene) (PEDOT) as solid-contact material to diminish charge-transfer resistance and water layer potential. Conventional ion-selective electrodes (ISEs) with internal filling solution were used for comparison. The designed electrodes showed near Nernstian slopes of 28.2 ± 0.7 (r² = 0.999) over the concentration range of 1.0 × 10-6-1.0 × 10-2 M with the limit of detection 0.026 µg/mL over the pH range 4.2-9.0. The electrode exhibited good selectivity for diquat cations over a large number of organic and inorganic cations. The sensor was successfully introduced for direct measurement of diquat content in commercial pesticide preparations and different spiked potato samples. The results showed that the proposed electrode has a fast and stable response, good reproducibility, and applicability for direct assessment of diquat content. The proposed potentiometric method is simple and accurate in comparison with the reported HPLC methods. Besides, it is applicable to turbid and colored sample solutions.

Supramolecular Solvent-Based Liquid Phase Microextraction Combined with Ion-Pairing Reversed-Phase HPLC for the Determination of Quats in Vegetable Samples

In this study, we used anion supramolecular solvent (SUPRAS) prepared from a mixture of an anionic surfactant, sodium dodecyl sulfate (SDS), and a cationic surfactant, tetrabutylammonium bromide (TBABr), as the extraction solvent in liquid phase microextraction (LPME) of paraquat (PQ) and diquat (DQ). The enriched PQ and DQ in the SUPRAS phase were simultaneously analyzed by ion-pairing reversed-phase high performance liquid chromatography. PQ and DQ were successfully extracted by LPME via electrostatic interaction between the positive charge of the quats and the negative charge of SUPRAS. PQ, DQ, and ethyl viologen (the internal standard) were separated within 15 min on a C18 column, with the mobile phase containing 1-dodecanesulfonic acid and triethylamine, via UV detection. The optimized conditions for the extraction of 10 mL aqueous solution are 50 μL of SUPRAS prepared from a mixture of SDS and TBABr at a mole ratio of 1:0.5, vortexed for 10 s at 1800 rpm, and centrifugation for 1 min at 3500 rpm. The obtained enrichment factors were 22 and 26 with limits of detection of 1.5 and 2.8 µg L^-1 for DQ and PQ, respectively. The precision was good with relative standard deviations less than 3.86%. The proposed method was successfully applied for the determination of PQ and DQ in vegetable samples and recoveries were found in the range of 75.0% to 106.7%.

High throughput residue analysis of paraquat and diquat involving hydrophilic interaction liquid chromatographic separation and mass spectrometric determination

A selective, sensitive and robust LC-MS/MS method is reported for the determination of the residues of paraquat and diquat in various fruit matrices, including grape, apple and pomegranate. The extraction with acidified water (0.1 M HCl) at 80°C (15 min) offered superior recoveries for both analytes with a significantly lower matrix effects as compared to the extraction with acidified methanol by the methods reported in the existing literature. The optimised HPLC conditions on hydrophilic interaction liquid chromatography (HILIC) columns, when coupled with electrospray ionisation-tandem mass spectrometry, offered their limit of quantification at 0.01 mg kg^-1. The analysis on an XBridge HILIC column required a thorough optimisation of the gradient programme to induce chromatographic separation and minimise matrix effects. This was not necessary when a CORTECS HILIC column was used, which provided selective and sensitive analysis within 5 min runtime using isocratic flow. Isotopically labelled internal standards corrected the recoveries of both analytes within 70-120% (RSD < 20%). For the first time, the applications of high resolution accurate mass analysis in the 'time of flight - multiple reaction monitoring' mode have been demonstrated as a complementary means of targeted screening of these compounds at 0.01 mg kg^-1 level. The method has a strong potential for applications in both official control and by those involved in food production for checking compliance with the EU MRLs.

A simple approach for the ultrasensitive detection of paraquat residue in adzuki beans by surface-enhanced Raman scattering

Paraquat (PQ), has been used in many countries for controlling weed growth in agriculture because of its quick-acting and nonselective contact with green plant tissue.

Simultaneous Determination and Quantitation of Paraquat, Diquat, Glufosinate and Glyphosate in Postmortem Blood and Urine by LC-MS-MS

A simple method, incorporating protein-precipitation/organic backwashing and liquid chromatography-tandem mass spectrometry (LC-MS-MS), has been successfully developed for the simultaneous analysis of four highly water-soluble and less volatile herbicides (paraquat, diquat, glufosinate and glyphosate) in ante- and postmortem blood, urine and gastric content samples. Respective isotopically labeled analogs of these analytes were adopted as internal standards. Acetonitrile and dichloromethane were used for protein precipitation and organic solvent backwashing, respectively, followed by injecting the upper aqueous phase into the LC-MS-MS system. Chromatographic separation was achieved using an Agilent Zorbax SB-Aq analytical column, with gradient elution of 15 mM heptafluorobutyric acid and acetonitrile. Mass spectrometric analysis was performed under electrospray ionization in positive-ion multiple reaction monitoring mode. The precursor ions and the two transition ions (m/z) adopted for each of these four analytes were paraquat (185; 169 and 115), diquat (183; 157 and 78), glufosinate (182; 136 and 119) and glyphosate (170; 88 and 60), respectively. Analyte-free blood and urine samples, fortified with the analytes of interest, were used for method development/validation and yielded acceptable recoveries of the analytes; interday and intraday precision and accuracy data; calibration linearity and limits of detection and quantitation. This method was successfully incorporated into an overall analytical scheme, designed for the analysis of a broad range of compounds present in postmortem samples, helpful to medical examiners' efforts to determine victims' causes of death.

Optimized ultra performance liquid chromatography tandem high resolution mass spectrometry method for the quantification of paraquat in plasma and urine

A simple, sensitive and specific ultra performance liquid chromatography coupled to electrospray tandem high resolution mass spectrometry (UPLC-ESI-HRMS/MS) method has been developed and validated for quantification of paraquat in plasma and urine. The sample preparation was carried out by one-step protein precipitation with acetonitrile. The paraquat was separated with a HILIC column in 10min. Detection was performed using Q Exactive Orbitrap mass spectrometer by Targeted-MS/MS scan mode. Methodological parameters, such as ammonium formate concentration, formic acid concentration, spray voltage, capillary temperature, heater temperature and normalized collision energy were optimized to achieve the highest sensitivity. The calibration curve was linear over the concentration range of LOQ-1000ng/mL. LOD was 0.1 and 0.3ng/mL, LOQ was 0.3 and 0.8ng/mL for urine and plasma, respectively. The intra- and inter-day precisions were <7.97% and 4.78% for plasma and urine. The accuracies were within the range 93.51-100.90%. The plasma and urine matrices had negligible relative matrix effect in this study. This method was successfully applied to determine paraquat concentration in plasma samples with hemoperfusion from 5 suspected paraquat poisoning patients.

Ionic liquid-modified silica-coated magnetic nanoparticles: promising adsorbents for ultra-fast extraction of paraquat from aqueous solution

In the present study, ionic liquid-modified silica-coated magnetic nanoparticles (Fe3O4@SiO2@IL) were synthesized and applied as adsorbents for extraction and determination of paraquat (PQ) followed by high-performance liquid chromatography. For assurance of the extraction efficiency, the obtained results were compared with those obtained by bared magnetic nanoparticles (MNPs). Experimental design and response surface methodology were used for optimization of different parameters which affect extraction efficiency of paraquat using both adsorbents. Under the optimized conditions, extraction recoveries in the range of 20-25 and 35-40 % with satisfactory repeatability values (RSDs%, n = 4) less than 5.0 % were obtained for bared MNPs and Fe3O4@SiO2@IL, respectively. The limits of detection were 0.1 and 0.25 μg/L using Fe3O4@SiO2@IL and bared MNPs, respectively. The linearity was obtained in the range of 0.25 to 25 μg/L and 0.5 to 25 μg/L for Fe3O4@SiO2@IL and bared MNPs, respectively, with the coefficients of determination better than 0.9950. Finally, Fe3O4@SiO2@IL was chosen as superior adsorbent due to more dispersion ability, higher extraction recovery, lower detection limit, as well as better linearity and repeatability. Calculated errors (%) were in the range of 3 to 10 % depicting acceptable accuracy for the analysis of PQ by the proposed method. Finally, the method was successfully applied for extraction and determination of PQ in some water and countryside soil samples.

Clearance rate and BP-ANN model in paraquat poisoned patients treated with hemoperfusion

In order to investigate the effect of hemoperfusion (HP) on the clearance rate of paraquat (PQ) and develop a clearance model, 41 PQ-poisoned patients who acquired acute PQ intoxication received HP treatment. PQ concentrations were determined by high performance liquid chromatography (HPLC). According to initial PQ concentration, study subjects were divided into two groups: Low-PQ group (0.05–1.0 μg/mL) and High-PQ group (1.0–10 μg/mL). After initial HP treatment, PQ concentrations decreased in both groups. However, in the High-PQ group, PQ levels remained in excess of 0.05 μg/mL and increased when the second HP treatment was initiated. Based on the PQ concentrations before and after HP treatment, the mean clearance rate of PQ calculated was 73 ± 15%. We also established a backpropagation artificial neural network (BP-ANN) model, which set PQ concentrations before HP treatment as input data and after HP treatment as output data. When it is used to predict PQ concentration after HP treatment, high prediction accuracy (R = 0.9977) can be obtained in this model. In conclusion, HP is an effective way to clear PQ from the blood, and the PQ concentration after HP treatment can be predicted by BP-ANN model.

Serum paraquat concentration detected by spectrophotometry in patients with paraquat poisoning

BACKGROUND

Paraquat (PQ) is a world-wide used herbicide and also a type of common poison for suicide and accidental poisoning. Numerous studies have proved that the concentration of serum PQ plays an important role in prognosis. Spectrophotometry, including common spectrophotometry and second-derivative spectrophotometry, is commonly used for PQ detection in primary hospitals. So far, lack of systematic research on the reliability of the method and the correlation between clinical features of patients with PQ poisoning and the test results has restricted the clinical use of spectrophotometry. This study aimed to evaluate the reliability and value of spectrophotometry in detecting the concentration of serum PQ.

METHODS

The wavelengths for detecting the concentration of serum PQ by common and second-derivative spectrophotometry were determined. Second-derivative spectrophotometry was applied to detect the concentration of serum PQ. The linear range and precision for detection of PQ concentration by this method were confirmed. The concentration of serum PQ shown by second-derivative spectrophotometry and HPLC were compared in 8 patients with PQ poisoning. Altogether 21 patients with acute poisoning 4 hours after PQ ingestion treated in the period of October 2008 to September 2010 were retrospectively reviewed. The patients were divided into higher and lower than 1.8 μg/mL groups based on their concentrations of serum PQ measured by second-derivative spectrophotometry on admission. The severity of clinical manifestations between the two groups were analyzed with Student's t test or Fisher's exact test.

RESULTS

The absorption peak of 257 nm could not be found when common spectrophotometry was used to detect the PQ concentration in serum. The calibration curve in the 0.4-8.0 μg/mL range for PQ concentration shown by second-derivative spectrophotometry obeyed Beer's law with r=0.996. The average recovery rates of PQ were within a range of 95.0% to 99.5%, relative standard deviation (RSD) was within 1.35% to 5.41% (n=6), and the lower detection limit was 0.05 μg/mL. The PQ concentrations in serum of 8 patients with PQ poisoning shown by second-derivative spectrophotometry were consistent with the quantitative determinations by HPLC (r=0.995, P<0.0001). The survival rate was 22.2% in patients whose PQ concentration in serum was more than 1.8 μg/mL, and the incidences of acidosis, oliguria and pneumomediastinum in these patients were 55.6%, 55.6% and 77.8%, respectively. These clinical manifestations were different significantly from those of the patients whose PQ concentration in serum was less than 1.8 μg/mL (P<0.05).

CONCLUSIONS

For common spectrophotometry, the wavelength at 257 nm was not suitable for detecting serum PQ as no absorbance was shown. Second-derivative spectrophotometry was reliable for detecting serum paraquat concentration. Serum PQ concentration detected by second-derivative spectrophotometry could be used to predict the severity of clinical manifestations of patients with PQ poisoning, and PQ content higher than 1.8 μg/mL 4 hours after ingestion could be an important predictive factor for poor prognosis.

Fluorescence detecting of paraquat using host-guest chemistry with cucurbit[8]uril

Paraquat (PQ) is one of the most widely used herbicides in the world, which has a good occupational safety record when used properly. While, it presents high mortality index after intentional exposure. Accidental deaths and suicides from PQ ingestion are relatively common in developing countries with an estimated 300,000 deaths occurring in the Asia–Pacific region alone each year, and there are no specific antidotes. Good predictors of outcome and prognosis may be plasma and urine testing within the first 24 h of intoxication. A fluorescence enhancement of approximately 30 times was seen following addition of PQ to a solution of the supramolecular compound 2MB@CB[8], which comprised two methylene blue (MB) molecules within one cucurbit[8]uril (CB[8]) host molecule. The fluorescence intensity was linearly proportional to the amount of PQ added over the concentration range 2.4 × 10⁻¹⁰ M–2.5 × 10⁻⁴ M. The reaction also occurred in living cells and within live mice.

Quantification of paraquat in postmortem samples by gas chromatography-ion trap mass spectrometry and review of the literature

Paraquat (PQ) is an herbicide implicated in numerous fatalities, mainly caused by voluntary ingestion. Several methods have been used to quantify PQ in plasma and urine samples of intoxicated humans as a predictor of clinical outcome. There is no validated method for the analysis of PQ in postmortem samples. Therefore, the aim of this study was to develop an analytical method, using gas chromatography-ion trap mass spectrometry (GC-IT/MS) after solid-phase extraction, to quantify PQ in postmortem samples, namely in whole blood, urine, liver, lung and kidney, to cover the routes of distribution, accumulation and elimination of PQ. The method proved to be selective as there were no interferences of endogenous compounds with the same retention time as PQ and ethyl paraquat (internal standard). The regression analysis for PQ was linear in the range 0-10 µg/mL. The detection limits ranged from 0.0076 µg/mL for urine to 0.047 µg/mL for whole blood, and the recoveries were suitable for forensic analysis. The proposed GC-IT/MS method provided an accurate and simple assay with adequate precision and recovery for the quantification of PQ in postmortem samples. The proof of applicability was performed in two fatal PQ intoxications. A review of the analytical methods for the determination of quaternary ammonium herbicides is also provided for a better understanding of the presently available techniques.

Method for measurement of the quaternary amine compounds paraquat and diquat in human urine using high-performance liquid chromatography-tandem mass spectrometry

We have developed a highly selective and sensitive analytical method to quantify paraquat and diquat by use of high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). The sample preparation includes solid phase extraction that uses weak cation exchange cartridges. These highly charged dual quaternary amines were not retained by standard reversed phase columns, but they could be adequately separated through HPLC with a HILIC column. The detection was carried out with a triple quadrupole mass spectrometer with an electrospray ionization probe in positive ion mode in multiple reaction monitoring. Repeated analysis in human urine samples spiked with low (5 ng/ml), medium (15 ng/ml), and high (30 ng/ml) concentrations of the analytes yielded relative standard deviations of less than 9%. The extraction efficiencies ranged from 77.7% to 94.2%. The limits of detection were in the range of 1 ng/ml.

Application of an enzyme-linked immunosorbent assay for the analysis of paraquat in human-exposure samples

Paraquat is a toxic quaternary ammonium compound used as an herbicide around the world. Easy, fast, and inexpensive but sensitive methods are needed to study the effects of long-term, low-level exposure of paraquat on human health. An enzyme-linked immunosorbent assay (ELISA) was used for quantification of paraquat in urine and air-filter samples collected in a human-exposure study among farm workers in Costa Rica. A sample pretreatment consisted of removal of interfering substances using solid-phase extraction resin columns. The precision and accuracy of the method were tested using duplicate spiked urine samples. The correlation between results for blind samples obtained using ELISA and liquid chromatography-mass spectrometry was significant (R2 = 0.945 and 0.906 for spiked and field samples, respectively). With an LOQ of 2 ng mL(-1), this ELISA method was able to distinguish the exposed from the nonexposed farm workers. For the air-filter analysis, paraquat was extracted by 9 M H2SO4 at 60 degrees C for 12 hours, and the results obtained by ELISA showed good correlation (R2 = 0.918) with the spectrophotometric (256 nm) measurements. Paraquat in acid-stabilized urine samples was very stable, and no significant losses were detected during a 3-month storage at room temperature, at 4 degrees C, or at -20 degrees C.

Ultrasensitive quantitative determination of paraquat: application to river, ground, and drinking water analysis in an agricultural area

The water specimens were collected from wells and irrigation ditches in the agricultural area to the south of Milan and from Olona River and Mantua Lake and analyzed for paraquat detection. The assay was performed using a specific polyclonal antibody raised in sheep and rabbit anti-sheep IgG conjugated with a chelating molecule 4,7-bis(chlorosulfophenyl)-1,10-phenanthroline-2,9-dicarboxylic acid complexed with Eu3+ as a fluorescent marker. Bovine serum albumin conjugated with 5-(1'-methyl[4,4']bipyridinyl-1-yl)pentanoic acid was used in solid phase preparation. The sensitivity achieved was 20 ng L(-1). The recovery in samples spiked with three different PQ concentrations was between 88 and 108%.

Quantitative analysis of the microbial metabolome by isotope dilution mass spectrometry using uniformly 13C-labeled cell extracts as internal standards

A novel method was developed for the quantitative analysis of the microbial metabolome using a mixture of fully uniformly (U) (13)C-labeled metabolites as internal standard (IS) in the metabolite extraction procedure the subsequent liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) analysis. This mixture of fully U (13)C-labeled metabolites was extracted from biomass of Saccharomyces cerevisiae cultivated in a fed-batch fermentation on fully U (13)C-labeled substrates. The obtained labeled cell extract contained, in principle, the whole yeast metabolome, allowing the quantification of any intracellular metabolite of interest in S. cerevisiae. We have applied the labeled cell extract as IS in the analysis of glycolytic and tricarboxylic acid (TCA) cycle intermediates in S. cerevisiae sampled in both steady-state and transient conditions following a glucose pulse. The use of labeled IS effectively reduced errors due to variations occurring in the analysis and sample processing. As a result, the linearity of calibration lines and the precision of measurements were significantly improved. Coextraction of the labeled cell extract with the samples also eliminates the need to perform elaborate recovery checks for each metabolite to be analyzed. In conclusion, the method presented leads to less workload, more robustness, and a higher precision in metabolome analysis.

Analytical mass spectrometry of herbicides

Herbicides are chemical substances that are applied to agricultural soils, gardens, lawns, or plants to destroy or to prevent the growth of undesirable vegetation. The herbicides included in this review are generally synthetic organic compounds that are ingredients in commercial herbicide products that were designated active during late 2002 in the U.S. Environmental Protection Agency's database of registered and canceled pesticide products. The compounds are organized into 21 categories according to their general chemical structures or a common structural group. The herbicides in each category are discussed in terms of their structures, their database electron ionization mass spectra, and their amenability to separation and measurement with gas chromatography, reversed-phase liquid chromatography, and capillary electrophoresis combined with mass spectrometry. Ionization techniques that are considered here are mainly electron ionization, electrospray, and atmospheric pressure chemical ionization. Sixty-six references are provided to herbicide reviews, and to the recent herbicide analytical chemistry and mass spectrometry research literature.

Cluster ions of diquat and paraquat in electrospray ionization mass spectra and their collision-induced dissociation spectra

Cluster ions such as [Cat+X+nM](+) (n = 0-4); [Cat-H+nM](+) (n = 1-3); and [2(Cat-H)+X+nM](+) (n = 0-2), where Cat, X, and M are the dication, anion, and neutral salt (CatX(2)), respectively, are observed in electrospray ionization (ESI) mass spectrometry of relatively concentrated solutions of diquat and paraquat. Collision-induced dissociation (CID) reactions of the clusters were observed by tandem mass spectrometry (MS/MS), including deprotonation to form [Cat-H](+), one-electron reduction of the dication to form Cat(+.), demethylation of the paraquat cation to form [Cat-CH(3)](+), and loss of neutral salt to produce smaller clusters. The difference in acidity and reduction power between diquat and paraquat, evaluated by thermodynamical estimates, can rationalize the different fractional yields of even-electron ([Cat-H](+) and its clusters) and odd-electron (mostly Cat(+)) ions in ESI mass spectra of these pesticides. The [Cat+n. Solv](2+) doubly charged cluster ions, where n <or= 2 and Solv is the solvent molecule (methanol and/or water), are only observed as very weak peaks in precursor ion CID spectra of the Cat(2+) salt cation at low collision energy. The presence of an anion and a solvent molecule in a cluster is assumed to be related to existence of tight and loose ion pairs, respectively, in multiply charged droplets/ions formed by ESI. The results emphasize again the role of solution chemistry concepts such as acidity/basicity, redox power, and ion-pair formation, for ESI.