Highly selective-cathodic stripping voltammetric determination of copper with α-benzylmonooxime

Nano-level determination of copper with atomic absorption spectrometry after pre-concentration on N,N-(4-methyl-1,2-phenylene)diquinoline-2-carboxamide-naphthalene

A novel, simple, sensitive and effective method has been developed for selective extraction and pre-concentration of copper on N,N-(4-methyl-1,2-phenylene)diquinoline-2-carboxamide-naphthalene. After pre-concentration, copper was eluted from sorbent with hydrochloric acid, and then flame atomic absorption spectrometry (FAAS) was used for its determination. The effect of pH, sample flow rate and the volume and concentration of eluent on the recovery of the analyte was investigated and the optimum conditions were established. A pre-concentration factor of 400, and an adsorption capacity of 6.9 mg g(-1) of the solid-phase sorbent or 82.8 mg g(-1) of ligand was achieved using the optimum conditions. The calibration graph was linear in the range of 1.0-4000 ng mL(-1) with the detection limit of 1.0 ng mL(-1). A R.S.D. value of 2.4% was obtained by this method for 400 ng mL(-1) of Cu(2+) solution. This procedure has been successfully applied to separate and determine the ultra trace levels of copper in the environmental samples, free from the interference of some diverse ions.

Catalytic adsorptive stripping voltammetric determination of copper(II) on a carbon paste electrode

A catalytic adsorptive stripping voltammetric method for the determination of copper(II) on a carbon paste electrode (PCE) in an alizarin red S (ARS)-K2S2O8 system is proposed. In this method, copper(II) is effectively enriched by both the formation and adsorption of a copper(II)-ARS complex on the PCE, and is determined by catalytic stripping voltammetry. The catalytic enhancement of the cathodic stripping current of the Cu(II) in the complex results from a redox cycle consisting of electrochemical reduction of Cu(II) ion in the complex and subsequent chemical oxidation of the Cu(II) reduction product by persulfate, which reduces the contamination of the working electrode from Cu deposition and also improves analytical sensitivity. In Britton-Robinson buffer (pH 4.56+/-0.1) containing 3.6 x 10(-5) mol L(-1) ARS and 1.6 x 10(-3) mol L(-1) K2S2O8, with 180 s of accumulation at -0.2 V, the second-order derivative peak current of the catalytic stripping wave was proportional to the copper(II) concentration in the range of 8.0 x 10(-10) to approximately 3.0 x 10(-8) mol L(-1). The detection limit was 1.6 x 10(-10) mol L(-1). The proposed method was evaluated by analyzing copper in water and soil.

Adsorptive Stripping Voltammetric Determination of Copper(II) Ion Using Phenyl Pyridyl Ketoneoxime (PPKO)

A sensitive and selective procedure is presented for the voltammetric determination of copper(II) ion. The procedure involves an adsorptive accumulation of Cu2+-PPKO on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of reduction current of adsorbed complex at about -0.30 V (vs. SCE). The optimum conditions for the analysis of copper(II) ion include pH (5.8-7.0), 60 microgM PPKO and an accumulation potential of -0.5 V (vs. SCE). The peak current is proportional to the concentration of copper over the range 0.3-76 ng mL(-1) with a detection limit of 0.01ng mL(-1) with an accumulation time of 60 s. The speciation of different forms of complex between copper(II) ion and PPKO, using the Best (Martell program), followed pH measurement were examined. The method was applied to the determination of copper(II) ion content in real samples successfully.

Differential Pulse Anodic Stripping Voltammetric Determination of Traces of Copper with a Tobramycin-Nafion Modified Electrode

A Nafion-modified glassy carbon electrode incorporated with tobramycin for the voltammetric stripping determination of Cu2+ has been explored. The electrode was fabricated by tobramycin containing Nafion on the glassy carbon electrode surface. The modified electrode exhibited a significantly increased sensitivity and selectivity for Cu2+ compared with a bare glassy carbon electrode and the Nafion modified electrode. Cu2+ was accumulated in HAc-NaAc buffer (pH 4.6) at a potential of -0.6 V (vs. SCE) for 300 s and then determined by differential pulse anodic stripping voltammetry. The effects of various parameters, such as the mass of Nafion, the concentration of tobramycin, the pH of the medium, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 1.0 x 10(-9) to 5.0 x 10(-7) mol l(-1) with a correlation coefficient of 0.9971. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-8) and 2.0 x 10(-7) mol l(-1) Cu2+, respectively. The detection limit (three times signal to noise) was 5.0 x 10(-10) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determination of copper in water samples, and also in analytical reagent-grade salts with satisfactory results.

Spectrophotometric and AAS Determination of Trace Amounts of Cobalt after Preconcentration by Using .ALPHA.-Benzilmonoxime-Microcrystalline Naphthalene

The formed cobalt-a-benzilmonoxime complex was adsorbed onto microcrystalline naphthalene. Then it was determined by zero and first derivative spectrophotometry and by atomic absorption spectrophotometry (AAS) after dissolving into chloroform and methylisobutylketone (MIBK), respectively. Under optimum conditions, cobalt in the range of 1.0 - 20.0, 0.4 - 30.0 and 2.5 - 50.0 microg could be determined by spectrophotometry, first derivative spectrophotometry and AAS method, respectively. By the method, a preconcentration factor equal to approximately 30 for cobalt was obtained. The effect of diverse ions on the determination of 5.0 microg cobalt was also studied. The method was successfully applied to some pharmaceuticals and synthetic alloy samples.

A Facile Spectrophotometric Method for Cobalt Determination Using .ALPHA.-Benzilmonoxime in Sodium Dodecylsulfate Micellar Solutions

Alpha-benzilmonoxime in sodium dodecylsulfate micellar media has been used for the spectrophotometric determination of cobalt at pH 9.0. The linear range of calibration is 0.05-1.50 microg cm(-3) of cobalt at 380 nm with molar absorptivity of 3.72 x 10(4) dm3 mol(-1) cm(-1), which is about 1.5-times greater than that of the alpha-benzilmonoxime extraction based method. The relative standard deviations, recoveries, detection limit and effects of diverse ions on the determination of cobalt were studied. These analytical results were satisfactory. The method was successfully applied to the determination of cobalt in the various samples.

Differential pulse adsorption stripping voltammetric determination of copper(II) with 2-mercaptobenzimidazol at a hanging mercury-drop electrode

Copper(II) was selectively accumulated on a hanging mercury-drop electrode by using 2-mercaptobenzimidazole. Ensuing measurements were carried out by differential pulse adsorption stripping voltammetry. Factors affecting the accumulation, reduction, and stripping steps were investigated and a procedure was developed. The optimum conditions for the analysis of copper were pH 5.0, 5.33 x 10(-5) M 2-mercaptobenzimidazole and an accumulation potential of -0.10 V (vs. Av/AgCl). A linear range was obtained in the concentration range 0.2-100 ng/ml with a 90 s accumulation time and a scan rate of 16 mV/s. For ten successive determinations of 1.0, 20.0 and 70.0 ng/ml copper(II), relative standard deviations of 4.2, 3.5 and 2.8%, respectively, were obtained. The developed method was applied to the determination of copper in commercial salts and aluminium alloys.

A sensitive and simple extractive-spectrophotometric method for the determination of microgram amount of cobalt by using alpha-benzilmonoxime

Alpha-benzilmonoxime has been used for the extraction and determination of cobalt at microgram amount. The reagent reacts with cobalt(II) in the pH range of 8.8 - 9.3 to form a yellow-color chelate, which is extracted in chloroform, toluene, and some other non-polar solvents. The chelate is stable in chloroform for about one day. Under the optimum conditions of the a-benzilmonoxime concentration and pH of 9.0, Beer's law was obeyed in the concentration range of 0.08 - 2.2 microg/ml cobalt. The molar absorptivity of the extracted species was 2.55 x 10(4) dm3/mol cm at 380 nm, with a detection limit of 0.01 microg/ml cobalt. Relative standard deviations of 0.4, 0.8 and 2.3% were found for the determination of cobalt concentrations of 2.2, 1.1 and 0.08 microg/ml, respectively. The effect of diverse ions on the determination of 1.00 microg/ml of cobalt has been studied. The method was applied to the determination of cobalt in vitamin B12 and B-complex ampoules, a Co2O3-Co3O4 laboratory chemical mixture and some synthetic alloy samples. The method is sensitive, simple, rapid and accurate.