The removal of heavy metal from aqueous solutions by sawdust adsorption - removal of copper

A practical approach to demonstrate the circular economy in remediation of textile dyes using nutraceutical industrial spent

We used Nutraceutical Industrial Coriander Seed Spent (NICSS), a readily available, cheap, eco-friendly, and ready-to-use material, as an innovative adsorbent for the bioremediation of a bisazo Acid Red 119 (AR 119) dye, which is likely a mutagen from textile industrial effluents (TIE). A laboratory-scale experiment was tailored to demonstrate the framework of the circular economy (CE) in the remediation of textile dyes using Nutraceutical Industrial Spent to align with the principles of sustainability and valorization. An experimental q e value of 97.00 mg g-1 was obtained. For the practicality and effectiveness of the method, a two-level fractional factorial experimental design (FFED) was employed to determine variables that influence the adsorption capacity of NICSS. At optimal settings (pH of 1.4, adsorbent dosage of 6.000 g L-1, adsorbent particle size of 96 μm, initial dye concentration of 599 mg L-1, adsorption duration of 173 min, orbital shaking speed of 165 rpm, and temperature of 35 °C), the maximum adsorption efficiency achieved through statistical optimization was 614 mg g-1. Six factors influencing the adsorption process were examined experimentally and were considered important for commercialization. Three orders of magnitude were applied to the identified variables in scaling experiments. Adsorption-equilibrium data were analyzed using nine isotherm models. The best fit was discovered to be the Vieth-Sladek adsorption isotherm model. The suitable mechanism for the overall rate of the adsorption process was a pseudo-second-order reaction: mass-transfer mechanistic studies were predicted to predominate over the diffusion process. NICSS was characterized using SEM and FTIR spectroscopy. Utilizing plastic trash, the dye-adsorbed NICSS that was recovered as "sludge" was utilized as a reinforcing material to create composites. Dye-adsorbed NICSS thermoplastic and thermoset composites were studied and compared with NICSS composites in terms of their physicomechanical and chemical properties.

Removal of organic and inorganic effluents from wastewater by using degradation and adsorption properties of transition metal-doped nickel ferrite

Removal of water pollutants (methylene blue dye and heavy metals) was achieved by zinc/manganese-doped nickel ferrites (Ni1 - xMxFe2O4, where x = 0.00, 0.025, 0.10). Degradation of dye was achieved under natural solar light illumination. Degradation studies of dye were conducted under different parameters such as contact time-80 min, dye's concentration-5 mg/L, pH-7, and dosage of ferrites-15 mg. The adsorption of dye was studied using non-linear kinetics models (pseudo-first-order and pseudo-second-order) and isotherm models (Langmuir and Freundlich). The adsorption of dye followed pseudo-first-order kinetics (R2 = 0.99377) than second-order kinetics (R2 = 0.98063) and Langmuir isotherm model (R2 = 0.96095) than Freundlich model (R2 = 0.95962) with maximum adsorption efficiency of 29.62 mg/g. Doping of nickel ferrites caused an increase in the removal percentage of methylene blue dye (80 to 90%) and inorganic effluents (75 to 95% for lead and 47 to 82% for cadmium). In addition to this, band gap energy (2.43 to 3.26 eV) (UV-Vis spectroscopy), pore radius (65.2 to 74.8 A°), and specific surface area (16.45 to 27.95 m2/g) (BET analysis) were also increased. Generally, the results of the study revealed that synthesized nanoparticles can act as potential candidate for the removal of effluents from wastewater under optimum parameters along with recyclability, reusability, and separation under the influence of a magnetic field.

Phytochemistry, nutritional composition, health benefits and future prospects of Mespilus germanica L. (Medlar): A review

Mespilus germanica L., commonly known as medlar, is one of two species of the Rosaceae family. The medlar plant has a long history of use in gastronomy and healthcare. Medlar waste is used to extract hazardous heavy metals from contaminated water. The nutritional value of M. germanica fruits comes from their composition of carbohydrates, carotenoids, amino acids, organic acids, proteins, vitamins, fatty acids, and vital components. M. germanica fruit contains a high concentration of important phenolic components, which contribute to its anti-diabetic and antioxidant properties. Additionally, several studies have identified diverse biological properties of the M. germanica plant, including the cytotoxic, neurodegenerative, and antibacterial properties of its fruits and leaves. Scientists are investigating underutilized plant species to address sustainability issues in food production. This review study will provide a comprehensive examination of its chemical composition, medical applications, plant waste utilization, and potential biological activities.

Impacts of controlled microwave field irradiation on o-cresol and p-cresol adsorption capability of activated carbon

To access the feasibility of microwave in promoting adsorbability of carbonaceous adsorbents, microwave irradiation on activated carbon (AC) was conducted at powers of 400-800 W and duration of 10 min. Accordingly, the temperature rising of AC under microwave field were studied. Moreover, the alterations in physicochemical properties of AC and impacts on cresol isomer adsorption were investigated. Results indicated that the heating curve of AC displays the initial fast temperature rising stage and the final slow stage. Additionally, the bulk temperature at irradiation terminal increases with microwave power. The temperature rising further increases the pores with a diameter range of 1.00-6.00 nm of AC; it also increases the oxygenic functional groups of AC after irradiation at 400 W and 800 W, but decreases that of AC after irradiation at 640 W. The saturation adsorption capacity of o-cresol and p-cresol on the irradiated AC rises with elevated temperature. Additionally, the cresol isomer adsorption kinetics on the irradiated AC follows the Elovich model. The above-mentioned equilibrium and kinetics suggest that the cresol isomer adsorption on the irradiated AC is dominant by chemisorption. Finally, the optimum irradiation power for o-cresol and p-cresol adsorption is 800 W and 400 W, respectively, thereby fabricating AC with developed pores and abundant oxygenic functional groups. Accordingly, the saturation adsorption capacity of o-cresol and p-cresol reaches up to 111.11 mg·g-1 and 95.97 mg·g-1, respectively. Overall, microwave irradiation is a viable option to promote cresol isomer adsorption on AC.

Copper(II) ion removal by chemically and physically modified sawdust biochar

The difference between physical activations (by sonications) and chemical activations (by ammonia) on sawdust biochar has been investigated in this study by comparing the removal of Cu(II) ions from an aqueous medium by adsorption on sawdust biochar (SD), sonicated sawdust biochar (SSD), and ammonia-modified sawdust biochar (SDA) with stirring at room temperature, pH value of 5.5–6.0, and 200 rpm. The biochar was prepared by the dehydrations of wood sawdust by reflux with sulfuric acid, and the biochar formed has been activated physically by sonications and chemically by ammonia solutions and then characterized by the Fourier transform infrared (FTIR); Brunauer, Emmett, and Teller (BET); scanning electron microscope (SEM); thermal gravimetric analysis (TGA); and energy-dispersive spectroscopy (EDX) analyses. The removal of Cu(II) ions involves 100 mL of sample volume and initial Cu(II) ion concentrations (conc) 50, 75, 100, 125, 150, 175, and 200 mg L−1 and the biochar doses of 100, 150, 200, 250, and 300 mg. The maximum removal percentage of Cu(II) ions was 95.56, 96.67, and 98.33% for SD, SSD, and SDA biochars, respectively, for 50 mg L−1 Cu(II) ion initial conc and 1.0 g L−1 adsorbent dose. The correlation coefficient (R2) was used to confirm the data obtained from the isotherm models. The Langmuir isotherm model was best fitted to the experimental data of SD, SSD, and SDA. The maximum adsorption capacities (Qm) of SD, SSD, and SDA are 91.74, 112.36, and 133.33 mg g−1, respectively. The degree of fitting using the non-linear isotherm models was in the sequence of Langmuir (LNR) (ideal fit) > Freundlich (FRH) > Temkin (SD and SSD) and FRH (ideal fit) > LNR > Temkin (SDA). LNR and FRH ideally described the biosorption of Cu(II) ions to SD and SSD and SDA owing to the low values of χ2 and R2 obtained using the non-linear isotherm models. The adsorption rate was well-ordered by the pseudo-second-order (PSO) rate models. Finally, chemically modified biochar with ammonia solutions (SDA) enhances the Cu(II) ions’ adsorption efficiency more than physical activations by sonications (SSD). Response surface methodology (RSM) optimization analysis was studied for the removal of Cu(II) ions using SD, SSD, and SDA biochars.

Characterization and use of activated carbon synthesized from sunflower seed shell in the removal of Pb(II), Cd(II), and Cr(III) ions from aqueous solution

In this work, carbon-based nanomaterials such as active carbon which is prepared from common sunflower (Helianthus annuus) seed shell, and the characterization of the activated carbon NPs were studied using FTIR (Fourier transform infrared spectroscopy), XRD, SEM, EDS, and DTA techniques. Activated carbon NPs have been used in the adsorption of Pb(II), Cd(II), and Cr(III) ions from the aqueous phase. The results showed the highest adsorption efficiency was 99.9%, 92.45%, and 98% for Pb(II), Cd(II), and Cr(III) ions respectively at a temperature of 25 °C, pH = 7-9, and a time of 60 and 180 min, in addition to the accordance of the adsorption models for activated carbon with the Freundlich isotherm model at the value of R2 (0.9976, 0.9756, and 0.9907) and Langmuir isotherm model (0.966, 0.999, and 0.9873) of the Pb(II), Cd(II), and Cr(III) ions, respectively. We conclude the possibility of using activated carbon to have an extremely high sorption capacity across the conditions tested, with the highest adsorption efficiency having been >99% for Pb(II), Cd(II), and Cr(III) ions within the pH range 7-9 and a contact time of 60 to 180 min.

A critical review on the separation of heavy metal(loid)s from the contaminated water using various agricultural wastes

Wastewater contamination with heavy metal(loids)s has become a worldwide environmental and public health problem due to their toxic and non-degradable nature. Different methods and technologies have been applied for water/wastewater treatment to mitigate heavy metal(loid)-induced toxicity threat to humans. Among various treatment methods, adsorption is considered the most attractive method because of its high ability and efficiency to remove contaminants from wastewater. Agricultural waste-based adsorbents have gained great attention because of high efficiency to heavy metal(loids)s removal from contaminated water. Chemically modified biosorbents can significantly enhance the stability and adsorption ability of the sorbents. The two mathematical models of sorption, Freundlich and Langmuir isotherm models, have mostly been studied. In kinetic modeling, pseudo-second-order model proved better in most of the studies compared to pseudo-first-order model. The ion exchange and electrostatic attraction are the main mechanisms for adsorption of heavy metal(loid)s on biosorbents. The regeneration has allowed various biosorbents to be recycled and reused up to 4-5 time. Most effective eluents used for regeneration are dilute acids. For practical perspective, biosorbent removal efficiency has been elucidated using various types of wastewater and economic analysis studies. Economic analysis of adsorption process using agricultural waste-based biosorbents proved this approach cheaper compared to traditional commercial adsorbents, such as chemically activated carbon. The review also highlights key research gaps to advance the scope and application of waste peels for the remediation of heavy metal(loid)s-contaminated wastewater.

Modeling Cu removal from aqueous solution using sawdust based on response surface methodology

Copper (Cu), as one of the heavy metals widely used in industrial and agricultural activities, has a fundamental role in the pollution of water resources. Therefore, removing Cu from the aqueous solutions is considered an important challenge in the purification of water resources. Thus, in this study, sawdust with a diameter of 260-600 μm was used to remove Cu from the aqueous solutions. At first, sawdust was washed using distilled water and dried at laboratory temperature. Cu absorption experiments in closed conditions were performed based on the central composite design (CCD) model and with a range of initial Cu concentrations equal to 1-25 mgl-1. The amount of changes for other variables, including pH, time, and amount of sawdust, was equal to 2-10, 5-185 (min), and 5-25 (gl-1), respectively. After the completion of each test, the remaining Cu concentration in the solution was measured using atomic absorption, and the percentage of Cu removed was determined from the difference between the initial and final concentrations. The results showed that the CCD model has a favorable ability to predict Cu removal from the aqueous solutions (R2=0.90 and RSME=3.34%). Based on the Pareto analysis, contact time, the amount of sawdust, pH, and the Cu concentration had the most significant effect on removing Cu from the solution. Contact time, amount of sawdust, and pH were directly related, and the amount of dissolved Cu was proportional to the removal of Cu from the solution. Therefore, sawdust is desirable as a natural adsorbent, and the removal efficiency of Cu from solutions with low Cu concentration is very high (94%). In this regard, it is advised to use sawdust in the process of targeting Cu and heavy metals due to its low cost and availability.

Comprehensive Investigation of Cu2+ Adsorption from Wastewater Using Olive-Waste-Derived Adsorbents: Experimental and Molecular Insights

This study investigates the efficacy of adsorbents from locally sourced olive waste-encompassing olive skins, leaves, and pits, recovered from the initial centrifugation of olives (OWP)-and a composite with sodium alginate (OWPSA) for the removal of Cu2+ ions from synthetic wastewater. Experimental analyses conducted at room temperature, with an initial Cu2+ concentration of 50 mg/L and a solid/liquid ratio of 1 g/L, showed that the removal efficiencies were approximately 79.54% and 94.54% for OWP and OWPSA, respectively, highlighting the positive impact of alginate on adsorption capacity. Utilizing statistical physics isotherm models, particularly the single-layer model coupled to real gas (SLMRG), allowed us to robustly fit the experimental data, providing insights into the adsorption mechanisms. Thermodynamic parameters affirmed the spontaneity and endothermic nature of the processes. Adsorption kinetics were interpreted effectively using the pseudo-second-order (PSO) model. Molecular modeling investigations, including the conductor-like screening model for real solvents (COSMO-RS), density functional theory (DFT), and atom-in-molecule (AIM) analysis, unveiled intricate molecular interactions among the adsorbent components-cellulose, hemicellulose, lignin, and alginate-and the pollutant Cu2+, confirming their physically interactive nature. These findings emphasize the synergistic application of experimental and theoretical approaches, providing a comprehensive understanding of copper adsorption dynamics at the molecular level. This methodology holds promise for unraveling intricate processes across various adsorbent materials in wastewater treatment applications.

Nanocelluloses as sustainable membrane materials for separation and filtration technologies: Principles, opportunities, and challenges

Membrane technology is of great interest in various environmental and industrial applications, where membranes are used to separate different mixtures of gas, solid-gas, liquid-gas, liquid-liquid, or liquid-solid. In this context, nanocellulose (NC) membranes can be produced with predefined properties for specific separation and filtration technologies. This review explains the use of nanocellulose membranes as a direct, effective, and sustainable way to solve environmental and industrial problems. The different types of nanocellulose (i.e., nanoparticles, nanocrystals, nanofibers) and their fabrication methods (i.e., mechanical, physical, chemical, mechanochemical, physicochemical, and biological) are discussed. In particular, the structural properties of nanocellulose membranes (i.e., mechanical strength, interactions with various fluids, biocompatibility, hydrophilicity, and biodegradability) are reviewed in relation to membrane performances. Advanced applications of nanocellulose membranes in reverse osmosis (RO), microfiltration (MF), nanofiltration (NF), and ultrafiltration (UF) are highlighted. The applications of nanocellulose membranes offer significant advantages as a key technology for air purification, gas separation, and water treatment, including suspended or soluble solids removal, desalination, or liquid removal using pervaporation membranes or electrically driven membranes. This review will cover the current state of research, future prospects, and challenges in commercializing nanocellulose membranes with respect to membrane applications.

Removal of car battery heavy metals from wastewater by activated carbons: a brief review

Spent automobile batteries are one of the most significant secondary sources of harmful heavy metals for the environment. After being incorporated into the aquatic ecosystems, these metals disseminate to various plants, microorganisms, and the human body and cause multiple adverse effects. Activated carbons (ACs) have long been used as an effective adsorbent for different heavy metals in wastewater treatment processes. Although numerous research works have been published to date on this topic, they are scattered in the literature. In this review, we have assembled these works and provided an extensive overview of the application of ACs for treating spent car battery heavy metals (CBHMs) from aquatic systems. The preparation of ACs from different precursor materials, their application in the adsorption of CBHMs, the adsorption mechanism, kinetics, adsorption isotherms and various parameters that may affect the adsorption processes have been discussed in detail. A brief comparative analysis of the adsorption performances of ACs prepared from different precursor materials is also provided. Finally, recommendations for future research works are also offered.

Treatment of electroplating industry wastewater: a review on the various techniques

Water pollution by recalcitrant compounds is an increasingly important problem due to the continuous introduction of new chemicals into the environment. Choosing appropriate measures and developing successful strategies for eliminating hazardous wastewater contaminants from industrial processes is currently a primary goal. Electroplating industry wastewater involves highly toxic cyanide (CN), heavy metal ions, oils and greases, organic solvents, and the complicated composition of effluents and may also contain biological oxygen demand (BOD), chemical oxygen demand (COD), SS, DS, TS, and turbidity. The availability of these metal ions in electroplating industry wastewater makes the water so toxic and corrosive. Because these heavy metals are harmful to living things, they must be removed to prevent them from being absorbed by plants, animals, and humans. As a result, exposure to electroplating wastewater can induce necrosis and nephritis in humans and lung cancer, digestive system cancer, anemia, hepatitis, and maxillary sinus cancer with prolonged exposure. For the safe discharge of electroplating industry effluents, appropriate wastewater treatment has to be provided. This article examines and assesses new approaches such as coagulation and flocculation, chemical precipitation, ion exchange, membrane filtration, adsorption, electrochemical treatment, and advanced oxidation process (AOP) for treating the electroplating industry wastewater. On the other hand, these physicochemical approaches have significant drawbacks, including a high initial investment and operating cost due to costly chemical reagents, the production of metal complexes sludge that needs additional treatment, and a long recovery process. At the same time, advanced techniques such as electrochemical treatment can remove various kinds of organic and inorganic contaminants such as BOD, COD, and heavy metals. The electrochemical treatment process has several advantages over traditional technologies, including complete removal of persistent organic pollutants, environmental friendliness, ease of integration with other conventional technologies, less sludge production, high separation, and shorter residence time. The effectiveness of the electrochemical treatment process depends on various parameters, including pH, electrode material, operation time, electrode gap, and current density. This review mainly emphasizes the removal of heavy metals and another pollutant such as CN from electroplating discharge. This paper will be helpful in the selection of efficient techniques for treatment based on the quantity and characteristics of the effluent produced.

A hybrid biocomposite of Thamnidium elegans/olive pomace/chitosan for efficient bioremoval of toxic copper

Immobilized biomaterials have recently attracted researchers' attention in the field of environmental biotechnology due to their effective biosorption performances. In this respect, a novel hybrid biocomposite based on Thamnidium elegans cells, olive pomace, and chitosan (TE-OP@C) was produced and tested for the first time to remove a target pollutant. It was successfully employed to eliminate toxic Cu (II) ions. Uptake efficiency of the biocomposite was significantly greater than that of T. elegans and T. elegans-olive pomace, despite the much lesser amount of biocomposite used. Freundlich model best fitted the equilibrium data, and the pseudo-second-order kinetic model followed uptake. The maximum removal efficiencies in batch and continuous systems were determined to be 96 % and 98 %, respectively. After eight cycles, the biosorption and recovery efficiencies of TE-OP@C were higher than 90 %. Biocomposite was able to remove approximately 90 % and 88 % of Cu(II) from real wastewater in batch and continuous systems, respectively. FTIR analysis, zeta potential measurements, EDX, and SEM findings confirmed the Cu(II) uptake. XRD and BET analysis were also performed for biocomposite characterization. Breakthrough and exhausted points were determined as 80 and 150 min, respectively. The findings potentially lead to a new perspective for the treatment of copper contamination.

Copper migration and isotope fractionation in a typical paddy soil profile of the Yangtze Delta

To decipher Cu migration in paddy soils, which is important for understanding Cu supply in rice cultivation, Cu concentrations and isotope compositions were measured in a paddy soil profile in Suzhou, Eastern China, in the central Yangtze Delta. The results show that the variations in δ⁶⁵Cu values and Cu concentrations are not coupled along the profile. From top to bottom, the δ⁶⁵Cu values show small variations (0.07 ± 0.03‰ to 0.25 ± 0.01‰) in the upper layers (Ap-Br1), with a decrease in the subsurface Br2 layer (from 0.16 ± 0.04‰ to -0.19 ± 0.02‰), are almost homogeneous in the transitional Br3-BCrg layers (-0.01 ± 0.01‰ to -0.10 ± 0.02‰), and further decrease to -0.33 ± 0.01‰ in the permanently submerged G1 and G2 layers. Copper concentrations in the Ap layer show some fluctuations (25.8 to 29.0 μg/g), increase in the Br2 and Br3 layers (23.9 μg/g to 31.9 μg/g), and then decrease to 15.1 μg/g in the lower layers. The lack of coupling between δ⁶⁵Cu values and Cu concentrations may be ascribed to various physicochemical conditions in different layers. In the upper layers, Cu(I) enriched in light isotopes migrates downward with soil solutions under flooded conditions, leaving the soils of the Ap and Br1 layers enriched in heavy Cu isotopes. In the Br2 layer, the readsorption of light Cu isotopes on clay minerals results in decreased δ⁶⁵Cu values and increased Cu concentrations. In the Br3-BCrg layers, Cu(I) can be oxidized to Cu(II). The homogeneous Cu isotopes in these layers may mainly result from equilibrium adsorption of Cu on clay minerals. The decreased δ⁶⁵Cu values and Cu concentrations in the G layer are mainly attributed to groundwater transport in this layer. This study represents the Cu isotope variations in a paddy soil profile and the possible mechanism of Cu isotope fractionation.

Emerging architecture titanium carbide (Ti3C2Tx) MXene based photocatalyst toward degradation of hazardous pollutants: Recent progress and perspectives

MXenes family has aroused marvelous consideration as a frontier photoactive candidate for solar energy transformation and environmental remediation. 2D Ti₃C₂ exhibit a unique layered microstructure, large surface functional groups (-F, -OH, -O), substantial sorption selectivity, superior reduction efficiency, and electrical conductivity. Electronically conductive Ti₃C₂T_x with tunable energy band gap (0.92-1.75eV) makes it one of the most potential photoactive materials for photodegradation. The present review paper aims to design cost-effective heterojunctions and Schottky junctions of Ti₃C₂ with transition metal oxides, sulfides, g-C₃N₄, and other organic frameworks. The discussion mainly involves different aspects related to its tunable electronic structure, stability problems, and surface morphology control. In addition, the advantages of Ti₃C₂ in fabricating highly efficient Ti₃C₂ based catalytic junctions exhibiting suppressed charge carrier recombination are discussed with particular emphasis on their adsorption and redox properties for the removal of toxic dyes, heavy metal ions, and various pharmaceuticals. Finally, current challenges and research directions are outlined and prospected for the future development of Ti₃C₂ based photocatalytic systems.

A review on sources of heavy metals, their toxicity and removal technique using physico-chemical processes from wastewater

The world is facing environmental pollution and is in an alarming situation due to industrialization and urbanization. Especially, industrial wastewater discharge is causing serious pollution in the environment (water, soil, and air) and has become a challenge for researchers and scientists. Wastewater contains heavy metals like Cu, Ni, Cr, Pb, and Ar and causes toxicity in living beings and the environment. In this review, the sources of heavy metals and their toxicological effects on the environment have been reviewed. Various remediation techniques such as reverse osmosis, chemical precipitation, and ultrafiltration are being used for the treatment of wastewater, but still are limited in their efficiencies, residues, cost, and versatility. In this study, the most promising wastewater treatment technique, the physic-chemical technique, has been reviewed along with its working mechanism and efficiency. Further, the pros and cons of this technique and sub-techniques have also been reviewed to provide a basic understanding to beginners and a pathway to experts in the selection of better techniques.

Heavy Metal Ions Removal from Aqueous Solutions by Treated Ajwa Date Pits: Kinetic, Isotherm, and Thermodynamic Approach

In the current study we prepared cost-effective adsorbents based on ajwa date pits to remove Cu(II) ions from aqueous medium. Adsorbents were studied using scanning electron microscopy (SEM), FT-IR, and Brunauer-Emmett-Teller (BET) methods to characterize the surface functionalities, morphology, pore size, and particle size. The concentration of Cu(II) ions in the studied samples was determined by atomic adsorption spectrometry technique (AAS). Adsorption method was performed sequentially in a batch system followed by optimization by studying the numerous conditions, for instance the initial amounts of Cu(II) ions, dosages of the adsorbent, contact time, and pH of the solution. The ideal pH observed for maximum adsorption capacity was ~6.5. Langmuir and Freundlich isotherm models correctly predicted the investigation results, with the maximum monolayer adsorption capacities for Cu(II) ions at 328 K being 1428.57 mg/g (treated ajwa date pits, TADP) and 1111.1 mg/g for as produced ajwa date pits (ADP). It was revealed that TADP possess greater adsorption capability than ADP. Recovery investigations revealed that the saturated adsorbents eluted the maximum metal with 0.1 M HCl. Cu(II) ions adsorption was observed to be reduced by 80-89% after the second regeneration cycle. For the raw and chemically processed ajwa date pits adsorbent, the Langmuir model performed significantly better than the Freundlich model. The results demonstrated that the adsorbent made from ajwa date pits could be an economical and environmentally friendly alternative for removing Cu(II) ion pollutant from aqueous media.

Comparison and Optimization of Operational Parameters in Removal of Heavy Metal Ions from Aqueous Solutions by Low-Cost Adsorbents

Removal of heavy metal ions such as cadmium, lead, chromium, and iron from industrial wastewater is one of the most critical environmental problems. In this research, natural and low-cost adsorbents like the tangerine peel, bovine gut, tea waste, and sunflower seed hull were used for adsorption of heavy metals, such as chromium and iron, from contaminated solutions. The effects of environmental factors such as contact time, pH, the amount of adsorbent dose, and the initial concentration of metal ions in synthetic solution were investigated to obtain optimal conditions for the adsorption of heavy metal ions. For separation of chromium metal ion from aqueous solution, tea waste, tangerine peel, bovine gut, and sunflower seeds hull showed adsorption capacity of 85%, 51%, 46%, and 34%, respectively, while for the adsorption of iron (III), the adsorption capacities of tea waste, bovine gut, tangerine peel, and sunflower seeds hull were 96%, 96%, and 87%, respectively. The adsorption isotherms were in decent correlation with the Langmuir and Freundlich isotherm models. The adsorption kinetics of iron and chromium has a proper validation with the pseudo-second-order kinetic model. The BET and FTIR analyses were also reported to investigate the adsorption properties. This study suggests these adsorbents as low-cost and economical materials for the adsorption of chromium and iron ions with a high adsorption rate.

Current status of hypochlorite technology on the wastewater treatment and sludge disposal: Performance, principals and prospects

As cost-effective and high-efficient oxidants, the hypochlorite chemicals have been widely utilized for bleaching and disinfection. However, its potential applications in wastewater treatment and sludge disposal were less concerned. This paper mainly summarized the state-of-the-art applications of hypochlorite technology in wastewater and sludge treatment based on the main influencing factors and potential mechanisms of hypochlorite treatment. The results indicated that the hypochlorite approaches were not only effective in pollutants removal and membrane fouling mitigation for wastewater treatment, but also contributed to sludge dewatering and resource recovery for sludge disposal. The ClO^- and large generated free active radicals (i.e., reactive chlorine species and reactive oxygen species), which possessed strong oxidative ability, were the primary contributors to the pollutants decomposition, and colloids/microbes flocs disintegration during the hypochlorite treatment process. The performance of hypochlorite treatment was highly associated with various factors (i.e., pH, temperature, hypochlorite types and dosage). In combination with the reasonable activators (i.e., Fe²⁺ and ultraviolet), auxiliary agents, and innovative processes (i.e., hydrothermal and electro-oxidation), the operational performance of hypochlorite technology could be further enhanced. Finally, the feasibility and benefits of hypochlorite application for wastewater and sludge treatment were analyzed, and the existing challenges and future research efforts that need to be made have also prospected. The review can hopefully provide a theoretical basis and technical guidance to extend the application of hypochlorite technology for wastewater treatment and sludge disposal on large scale.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

Multivariate Optimization of Pb2+ Adsorption onto Ethiopian Low-Cost Odaracha Soil Using Response Surface Methodology

Lead pollution is a severe health concern for humankind. Utilizing water contaminated with lead can cause musculoskeletal, renal, neurological, and fertility impairments. Therefore, to remove lead ions, proficient, and cost-effective methods are imperative. In this study, the Odaracha soil which is traditionally used by the local community of the Saketa District was used as a novel low-cost technology to adsorb lead ions. Odaracha adsorbent was characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. The adsorption process followed the batch adsorption experiment. The response surface method was implemented to derive the operating variables’ binary interaction effect and optimize the process. According to the study’s experimental result, at optimum experimental conditions Odaracha adsorbent removes 98.17% of lead ions. Based on the result of the central composite design model, the Pb²⁺ ion removal efficiency of Odaracha was 97.193%, indicating an insignificant dissimilarity of the actual and predicted results. The coefficient of determination (R²) for Pb²⁺ was 0.9454. According to the factors’ influence indicated in the results of the central composite design model, all individual factors and the interaction effect between contact time and pH has a significant positive effect on lead adsorption. However, other interaction effects (contact time with dose and pH with dose) did not significantly influence the removal efficiency of lead ions. The adsorption kinetics were perfectly fitted with a pseudo-second-order model, and the adsorption isotherm was well fitted with the Freundlich isotherm model. In general, this study suggested that Odaracha adsorbent can be considered a potential adsorbent to remove Pb²⁺ ions and it is conceivable to raise its effectiveness by extracting its constituents at the industrial level.

Sawdust for the Removal of Heavy Metals from Water: A Review

The threat of the accumulation of heavy metals in wastewater is increasing, due to their abilities to inflict damage to human health, especially in the past decade. The world’s environmental agencies are trying to issue several regulations that allow the management and control of random disposals of heavy metals. Scientific studies have heavily focused on finding suitable materials and techniques for the purification of wastewaters, but most solutions have been rejected due to cost-related issues. Several potential materials for this objective have been found and have been compared to determine the most suitable material for the purification process. Sawdust, among all the materials investigated, shows high potential and very promising results. Sawdust has been shown to have a good structure suitable for water purification processes. Parameters affecting the adsorption mechanism of heavy metals into sawdust have been studied and it has been shown that pH, contact time and several other parameters could play a major role in improving the adsorption process. The adsorption was found to follow the Langmuir or Freundlich isotherm and a pseudo second-order kinetic model, meaning that the type of adsorption was a chemisorption. Sawdust has major advantages to be considered and is one of the most promising materials to solve the wastewater problem.

Java plum and amaltash seed biomass based bio-adsorbents for synthetic wastewater treatment

Biomass of Java plum (JP) and amaltash (AT) seeds were employed to remove arsenic from synthetic wastewater, cost effectively. The prepared biomasses were characterized by FE-SEM, EDX, FTIR, XRD, and ICP techniques. Experimentation the optimization study has been carried out by using Design-software 6.0.8. Response surface methodology has been applied to design the experiments where we have used three factors and three levels Box-Behnken design (BBD). Arsenic removal ability of bio-sorbents was evaluated and optimized by varying pH, adsorbent dose concentration of arsenic in synthetic wastewater. For 2.5 mg/L arsenic concentration and 80 mg adsorbent dose at pH 8.8 Java plum seeds (JP) based bio-adsorbent removed ∼93% and amaltash seeds (AT) based bio-adsorbent removed ∼91% arsenic from synthetic wastewater. The adsorption behaviour better explained following Freundlich model (R² = 0.99) compared to Temkin model (R² = 0.986) for As (III) ions. The adsorption capacity was 1.45 mg g^-1 and 1.42 mg g^-1 for JP and AT, respectively after 80 min under optimal set of condition. The adsorption kinetics was explained by either pseudo-first order model or Elovich model.

CaFu MOF as an efficient adsorbent for simultaneous removal of imidacloprid pesticide and cadmium ions from wastewater

Heavy metal ions and pesticides are the noteworthy toxic substances which must be removed from contaminated water for safeguarding public health. The higher levels of these substances in natural water may adversely affect the human health, climate and the eco-framework. The adsorptive removal of hazardous constituents employing metal organic frameworks has drawn considerable attention of researchers during the last decade. From this point of view, single crystal of calcium fumarate [Ca(C₄H₄O₄)_1.5 (H₂O)(CH₃OH)₂] has been developed and analyzed by single crystal X-ray crystallography which confirmed the formation of 3-D metal organic frameworks (MOFs). The synthesized MOFs was employed for simultaneous adsorptive removal of imidacloprid, a high consumption pesticide, and highly toxic Cd (II) from aqua ecosystem. The effect of variation in experimental conditions such as solution pH, adsorbent dosage, contact time, initial concentration and temperature on adsorption was systematically evaluated. Both the imidacloprid and Cd(II) exhibited maximum adsorption at pH 6.5 and 7.8, respectively. The equilibrium empirical data was fitted into Langmuir, Freundlich and Temkin isotherms. The adsorption capacity of CaFu MOFs was observed to be 467.23 and 781.2 mg g^-1 for imidacloprid and cadmium ions, respectively. The adsorbed pollutants were desorbed from the adsorbent using dilute HCl, and the material was reused for five adsorption-desorption cycles without any appreciable loss of adsorption capacity. Therefore, the 3-D CaFu MOFs could be utilized as a novel material for adsorptive removal of imidacloprid pesticide as well as Cd (II) from wastewater.

Influence of Wooden Sawdust Treatments on Cu(II) and Zn(II) Removal from Water

Organic waste materials and semi-products containing cellulose are used as low-cost adsorbents that are able to compete with conventional sorbents. In addition, their capacity to bind heavy metal ions can be intensified by chemical treatments using mineral and organic acids, bases, oxidizing agents, and organic compounds. In this paper, we studied the biosorption capacity of natural and modified wooden sawdust of poplar, cherry, spruce, and hornbeam in order to remove heavy metals from acidic model solutions. The Fourier transform infrared spectroscopy (FTIR) spectra showed changes of the functional groups due to the alkaline modification of sawdust, which manifested in the considerably increased intensity of the hydroxyl peaks. The adsorption isotherm models clearly indicated that the adsorptive behavior of metal ions in treated sawdust satisfied not only the Langmuir model, but also the Freundlich model. The adsorption data obtained for studied sorbents were better fitted by the Langmuir isotherm model for both metals, except for spruce sawdust. Surface complexation and ion exchange are the major mechanisms involved in metal ion removal. We investigated the efficiency of the alkaline modified sawdust for metal removal under various initial concentrations of Cu(II) and Zn(II) from model solutions. The highest adsorption efficiency values (copper 94.3% at pH 6.8 and zinc 98.2% at pH 7.3) were obtained for poplar modified by KOH. For all types of sawdust, we found that the sorption efficiency of modified sorbents was higher in comparison to untreated sawdust. The value of the pH initially increased more in the case of modified sawdust (8.2 for zinc removal with spruce NaOH) and then slowly decreased (7.0 for Zn(II) with spruce NaOH).

The facile synthesis of zoledronate functionalized hydroxyapatite amorphous hybrid nanobiomaterial and its excellent removal performance on Pb2+ and Cu2

In this paper, a simple chemical precipitation method was proposed to obtain zoledronate functionalized hydroxyapatite (zole-HAP) hybrid nano- biomaterials (zole-HAP-HNBM) which were firstly applied to adsorption. The characterizations of materials verified that the addition of zoledronate declined the crystallinity and transformed the morphology of HAP from short rod shape to microsphere, changed micro structure of the hybrid nanobiomaterial. Adsorption experiments carried out under different conditions showed that adsorption capacity of the nanobiomaterial, enhanced by the addition of zoledronate in preparation, which is equal to 1460.14 mg/g on Pb²⁺ and 226.33 mg/g on Cu²⁺ in optimum qualifications, was elevated more than the reported values in many literatures. At last, the sorption mechanisms of HAP and zole-HAP for Pb²⁺and Cu²⁺ were probed by experiments and Multifwn program calculation in details. It suggested that the dominant sorption mechanisms of HAP for Pb²⁺ were ion exchange and dissolution-precipitation rather than surface complexation, while besides the dissolution-precipitation mechanism, surface complexation may contribute more in the adsorption process of 10zole-HAP for Pb²⁺. Once considering HAP and 10zole-HAP, removal mechanisms of Cu²⁺ could involve surface complexation and ion exchange.

Variations in Cadmium Concentrations in Rice and Oxidation-Reduction Potential at the Soil Surface with Supplementation of Fermented Botanical Waste-based Amendment in Large-scale Farmland

We monitored the relationship between the cadmium (Cd) concentration uptake of rice and the oxidation-reduction potential (ORP) at the soil surface with the supplementation of fermented botanical waste-based amendment (FBWA), an organic fertilizer prepared from woody and food wastes. This study was carried out for 3 years in the western part of Jiangsu Province, China. It was found that the Cd concentration taken up by rice was correlated to a decreased the ORP of the cultivated soil. The yield of rice was ∼1.20 times higher than that of the control plot. The effects of reducing the Cd content in rice and increasing the rice yield remained for 2 years after FBWA application. Finally, Cd was immobilized in the soil with adsorption to FBWA or the decomposed products. The ORP measurement during rice cultivation might be a key index to predict the suppression effect of Cd uptake into the rice or limitation of the sustainable effect by the FBWA.

Lignin-rich sulfated wood nanofibers as high-performing adsorbents for the removal of lead and copper from water

Lignin-rich wood nanofibers (WNFs) were investigated as adsorbents for heavy metals. Lignin-free cellulose nanofibers (CNFs) produced from bleached cellulose fibers were used as a reference. Two raw materials were used to produce WNFs: groundwood pulp as industrially produced wood fibers and sawdust as an abundantly available low-value industrial side stream. WNFs and reference CNFs were produced using a reactive deep eutectic solvent to obtain nanofibers with abundant sulfate groups on their surfaces. With a similar amount of sulfate groups, WNFs had a higher adsorbent performance compared to CNFs and, at low metal concentrations (0.24 mmol/l), the removal of both metals was almost quantitate with WNFs. However, it was noted that, at pHs 4 and 5, the sodium present in the buffer solution interfered with the adsorption, leading to lower adsorption capacities compared to the capacity at pH 3. In addition, in the case of lead, the adsorption capacity dramatically decreased at a high metal concertation, indicating that a high lead concentration results in the saturation of adsorption sites of sulfated nanofibers, leading to a decreased adsorption capacity. Nevertheless, it was observed that WNFs had a higher tolerance to high metal concentrations than CNFs.

Heavy metals, nitrates and radionuclides in milk of cows depending on their stress resistance

The paper presents the results of studies on the content of cesium, strontium, zinc, cadmium, copper, lead and nitrates in the milk of Ukrainian black-and-white milk breed cows with different resistance to stress. The resistance of cows to stress was determined by concentration of cortisol in the blood one hour after a stress effect. The following factors were stressful: fixation of animals for one hour and pre-selection of blood by a veterinarian for general analysis. The objective of the research was establishing a connection between the different adaptive potential of Ukrainian black-and-white milk breeds and the ability of their bodies to excrete via the milk heavy metal salts, nitrates and radioactive elements which enter the body with food and water. The scientific hypothesis was that the state of pressure which occurs in the body under the influence of stress impairs homeostasis. It can affect the quantity and quality of products, it can cause disorders in the metabolic processes, the synthesis of milk components and introduction of some harmful substances into milk, which are differently accumulated in the body of cows with diverse reactions to stress and can be excreted with milk in at different levels. We established that different resistance of cows to stress can affect the concentration of the investigated harmful substances in milk. Concentration of lead, cadmium, zinc and nitrates was lower in milk of more stress-resistant cows (the first group). Their milk had a lower specific activity of 137Cs and 90Sr. For all the seasons, the reliable results were obtained only for nitrates, and 137Cs and 90Sr – in spring, summer and autumn. Thus, milk of cows with higher resistance to stress is safer in terms of contents of the investigated elements. We have drawn a conclusion that stress can affect the ability of the body to excrete via the milk harmful elements which enter the body with food and water. Perspectives of further research are determining the effect of cows’ stress resistance on the suitability of milk for the production of baby food products.

Functionalized graphene nanosheets as absorbent for copper (II) removal from water

Functionalized graphene nanosheets (FGNs) with high surface area and various functional groups were prepared by oxidation method. The characteristics of FGNs were studied by nitrogen adsorption using the Brunauer-Emmett-Teller (BET) method, Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), scanning electron microscope (SEM), energy dispersion spectrum (EDS), and atomic force microscopy (AFM). The specific surface area of obtained FGNs was measured as 834.06 m² g^-1, which was 20-40% higher than graphene nanosheets (GNs) before oxidation. An abundance of oxygen-containing functional groups, such as carboxyl, hydroxyl and epoxy groups, was grafted on the edge and surface of GNs. Moreover, FGNs demonstrated excellent adsorption and desorption performance when used as absorbent to remove Cu (II) from aqueous solution. The removal percentage could reach 96% within 1 h and remain 72% after 5 adsorption-desorption cycles. Adsorption process and mechanism were elucidated by kinetics models and isotherm models. The results showed FGNs has a great potential to be an adsorbent for removal copper ions from water.

Thermodynamic spectral and kinetic analysis of the removal of Cu(II) from aqueous solution by sodium carbonate treated rice husk

A new adsorbent for removing copper ions from aqueous solutions has been developed and characterized. The present study deals with the sorption of Cu(II) from aqueous solution on chemically pretreated sodium carbonate-treated rice husk (SCRH). The physico-chemical characteristics of rice husks were investigated to analyze their suitability to adsorb Cu(II) ions from water and wastewater. The raw rice husk (RRH), SCRH and Cu(II) adsorbed rice husk were analyzed by SEM-EDAX analysis. FTIR spectroscopy was also applied to identify functional groups, capable of adsorbing metal ions. Batch kinetic studies were conducted for the adsorption of Cu(II) on SCRH. It has been observed that 92.9-96.0% removal of Cu(II) is achieved at 4.8 mg of Cu(II)/g of adsorbent, adsorbent dose of 10 g L^-1 and initial Cu(II) concentration of 10 mg L^-1 in a temperature range of 15-50 °C. It was observed that the adsorption of Cu(II) on SCRH followed pseudo second-order kinetic and time to achieve equilibrium was found to be 60 min. The maximum uptake (97%) of Cu (II) was observed at pH 6. In this paper, an attempt has also been made to develop simple and readily understandable thermodynamic parameters related to sorption process at the equilibrium for understanding the adsorption mechanism. The Gibbs free energy ΔG° values for the adsorption processes of Cu(II) at 15, 30, 40 and 50 °C were calculated as -6.16, -6.84, -8.01 and -8.53 kJ mol^-1, respectively. The negative value of ΔG° indicates spontaneity of adsorption. The values of ΔH° and ΔS° for Cu(II) adsorption were calculated as 14.37 kJ mol^-1 and 70.92 J K^-1 mol^-1, respectively. The activation energy for the adsorption of Cu(II) was found to be 9 kJ mol^-1 which is a characteristic for diffusion limited processes.