Scanning electrochemical microscopy. 48. Hg/Pt hemispherical ultramicroelectrodes: fabrication and characterization

Nanogap-Resolved Adsorption-Coupled Electron Transfer by Scanning Electrochemical Microscopy: Implications for Electrocatalysis

Here, we demonstrate for the first time that the mechanism of adsorption-coupled electron-transfer (ACET) reactions can be identified experimentally. The electron transfer (ET) and specific adsorption of redox-active molecules are coupled in many electrode reactions with practical importance and fundamental interest. ACET reactions are often represented by a concerted mechanism. In reductive adsorption, an oxidant is simultaneously reduced and adsorbed as a reductant on the electrode surface through the ACET step. Alternatively, the non-concerted mechanism mediates outer-sphere reduction and adsorption separately when the reductant adsorption is reversible. In electrocatalysis, reversibly adsorbed reductants are ubiquitous and crucial intermediates. Moreover, electrocatalysis is complicated by the mixed mechanism based on simultaneous ACET and outer-sphere ET steps. In this work, we reveal the non-concerted mechanism for ferrocene derivatives adsorbed at highly oriented pyrolytic graphite as simple models. We enable the transient voltammetric mode of nanoscale scanning electrochemical microscopy (SECM) to kinetically control the adsorption step, which is required for the discrimination of non-concerted, concerted, and mixed mechanisms. Experimental voltammograms are compared with each mechanism by employing finite element simulation. The non-concerted mechanism is supported to indicate that the ACET step is intrinsically slower than its outer-sphere counterpart by at least four orders of magnitude. This finding implies that an ACET step is facilitated thermodynamically but may not be necessarily accelerated or catalyzed by the adsorption of the reductant. SECM-based transient voltammetry will become a powerful tool to resolve and understand electrocatalytic ACET reactions at the elementary level.

Use of Artificial Intelligence in Electrode Reaction Mechanism Studies: Predicting Voltammograms and Analyzing the Dissociative CE Reaction at a Hemispherical Electrode

Artificial intelligence (AI) is used to learn the key voltammetric characteristics of the dissociative CE mechanism via training from multiple simulations using bespoke code. This allows first for the prediction of voltammograms without the need for further simulations, given knowledge of the relevant experimental parameters (rate and equilibrium constants, electrode geometry, and diffusion coefficients). Second, it is applied to analyze noisy experimental voltammetry to characterize the mechanistic type and to successfully extract the key kinetic and thermodynamic parameters.

Microelectrochemical Techniques for Probing Kinetics at Liquid/Liquid Interfaces

We provide an overview of recent advances in microelectrochemical approaches to investigate the kinetics of various physicochemical processes that occur at the interface between two immiscible electrolyte solutions (ITIES). To place the advances in context, background material on the structure of the ITIES, derived from both experimental studies and computer simulation, is also provided. The main focus of the article is micro-ITIES techniques, single droplet measurements, microelectrochemical measurements at expanding droplets (MEMED) and scanning electrochemical microscopy (SECM). Recent developments in a combined SECM-Langmuir trough technique for probing diffusion processes across Langmuir monolayers at the water/air (W/A) interface are also highlighted, by considering an organic monolayer at a water surface as a special case of a liquid/liquid interface.

Detection of CO2•- in the Electrochemical Reduction of Carbon Dioxide in N,N-Dimethylformamide by Scanning Electrochemical Microscopy

The electrocatalytic reduction of CO₂ has been studied extensively and produces a number of products. The initial reaction in the CO₂ reduction is often taken to be the 1e formation of the radical anion, CO₂^•-. However, the electrochemical detection and characterization of CO₂^•- is challenging because of the short lifetime of CO₂^•-, which can dimerize and react with proton donors and even mild oxidants. Here, we report the generation and quantitative determination of CO₂^•- in N,N-dimethylformamide (DMF) with the tip generation/substrate collection (TG/SC) mode of scanning electrochemical microscopy (SECM). CO₂ was reduced at a hemisphere-shaped Hg/Pt ultramicroelectrode (UME) or a Hg/Au film UME, which were utilized as the SECM tips. The CO₂^•- produced can either dimerize to form oxalate within the nanogap between SECM tip and substrate or collected at SECM substrate (e.g., an Au UME). The collection efficiency (CE) for CO₂^•- depends on the distance (d) between the tip and substrate. The dimerization rate (6.0 × 10⁸ M^-1 s^-1) and half-life (10 ns) of CO₂^•- can be evaluated by fitting the collection efficiency vs distance curve. The dimerized species of CO₂^•-, oxalate, can also be determined quantitatively. Furthermore, the formal potential (E⁰') and heterogeneous rate constant (k₀) for CO₂ reduction were determined with different quaternary ammonium electrolytes. The significant difference in k₀ is due to a tunneling effect caused by the adsorption of the electrolytes on the electrode surface at negative potentials.

Scanning electrochemical microscopy: an analytical perspective

Scanning electrochemical microscopy (SECM) has evolved from an electrochemical specialist tool to a broadly used electroanalytical surface technique, which has experienced exciting developments for nanoscale electrochemical studies in recent years. Several companies now offer commercial instruments, and SECM has been used in a broad range of applications. SECM research is frequently interdisciplinary, bridging areas ranging from electrochemistry, nanotechnology, and materials science to biomedical research. Although SECM is considered a modern electroanalytical technique, it appears that less attention is paid to so-called analytical figures of merit, which are essential also in electroanalytical chemistry. Besides instrumental developments, this review focuses on aspects such as reliability, repeatability, and reproducibility of SECM data. The review is intended to spark discussion within the community on this topic, but also to raise awareness of the challenges faced during the evaluation of quantitative SECM data.

Cyclic Voltammetry Probe Approach Curves with Alkali Amalgams at Mercury Sphere-Cap Scanning Electrochemical Microscopy Probes

We report a method of precisely positioning a Hg-based ultramicroelectrode (UME) for scanning electrochemical microscopy (SECM) investigations of any substrate. Hg-based probes are capable of performing amalgamation reactions with metal cations, which avoid unwanted side reactions and positive feedback mechanisms that can prove problematic for traditional probe positioning methods. However, prolonged collection of ions eventually leads to saturation of the amalgam accompanied by irreversible loss of Hg. In order to obtain negative feedback positioning control without risking damage to the SECM probe, we implement cyclic voltammetry probe approach surfaces (CV-PASs), consisting of CVs performed between incremental motor movements. The amalgamation current, peak stripping current, and integrated stripping charge extracted from a shared CV-PAS give three distinct probe approach curves (CV-PACs), which can be used to determine the tip-substrate gap to within 1% of the probe radius. Using finite element simulations, we establish a new protocol for fitting any CV-PAC and demonstrate its validity with experimental results for sodium and potassium ions in propylene carbonate by obtaining over 3 orders of magnitude greater accuracy and more than 20-fold greater precision than existing methods. Considering the timescales of diffusion and amalgam saturation, we also present limiting conditions for obtaining and fitting CV-PAC data. The ion-specific signals isolated in CV-PACs allow precise and accurate positioning of Hg-based SECM probes over any sample and enable the deployment of CV-PAS SECM as an analytical tool for traditionally challenging conditions.

Ultramicroelectrode Studies of Self-Terminated Nickel Electrodeposition and Nickel Hydroxide Formation upon Water Reduction

The interaction between electrodeposition of Ni and electrolyte breakdown, namely the hydrogen evolution reaction (HER) via H₃O⁺ and H₂O reduction, was investigated under well-defined mass transport conditions using ultramicroelectrodes (UME's) coupled with optical imaging, generation/collection scanning electrochemical microscopy (G/C-SECM), and preliminary microscale pH measurements. For 5 mmol/L NiCl₂ + 0.1 mol/L NaCl, pH 3.0, electrolytes, the voltammetric current at modest overpotentials, i.e., between -0.6 V and -1.4 V vs. Ag/AgCl, was distributed between metal deposition and H₃O⁺ reduction, with both reactions reaching mass transport limited current values. At more negative potentials, an unusual sharp current spike appeared upon the onset of H₂O reduction that was accompanied by a transient increase in H₂ production. The peak potential of the current spike was a function of both [Ni(H₂O)₆]²⁺_(aq) concentration and pH. The sharp rise in current was ascribed to the onset of autocatalytic H₂O reduction, where electrochemically generated OH^- species induce heterogeneous nucleation of Ni(OH)_2(ads) islands, the perimeter of which is reportedly active for H₂O reduction. As the layer coalesces, further metal deposition is quenched while H₂O reduction continues albeit at a decreased rate as fewer of the most reactive sites, e.g., Ni/Ni(OH)₂ island edges, are available. At potentials below -1.5 V vs. Ag/AgCl, H₂O reduction is accelerated, leading to homogeneous precipitation of bulk Ni(OH)₂·xH₂O within the nearly hemispherical diffusion layer of the UME.

Electrochemical Imaging of Photoanodic Water Oxidation Enhancements on TiO2 Thin Films Modified by Subsurface Aluminum Nanodimers

Detecting metal plasmonic enhancements on the activity of semiconducting photoanodes for water oxidation is often obscured by the inherent electroactivity and instability of the metal in electrolyte. Here, we show that thin TiO₂ photoanodes modified by subsurface Al nanodimers (AlNDs) display enhancements that are consistent with plasmon modes. We directly observed enhancements by mapping the oxygen evolution rates on TiO₂/AlND patterns using scanning electrochemical microscopy (SECM) while exciting the surface plasmons of the nanodimers. This study highlights the importance of sample configuration for the in situ characterization of metal/photoanode interactions and suggests a route for Al-based plasmonics applied to photoelectrochemistry.

Electrocatalytic Amplification of Single Nanoparticle Collisions Using DNA-Modified Surfaces

Here we report on the effect of DNA modification on individual collisions between Pt nanoparticles (PtNPs) and ultramicroelectrode (UME) surfaces. These results extend recent reports of electrocatalytic amplification (ECA) arising from collisions between naked surfaces, and they are motivated by our interest in using ECA for low-level biosensing applications. In the present case, we studied collisions between naked PtNPs and DNA-modified Au and Hg UMEs and also collisions between DNA-modified PtNPs and naked Au and Hg UMEs. In all cases, the sensing reaction is the catalytic oxidation of N2H4. The presence of ssDNA (5-mer or 25-mer) immobilized on the UME surface has little effect on the magnitude or frequency of ECA signals, regardless of whether the electrode is Au or Hg. In contrast, when DNA is immobilized on the PtNPs and the electrodes are naked, clear trends emerge. Specifically, as the surface concentration of ssDNA on the PtNP surface increases, the magnitude and frequency of the current transients decrease. This trend is most apparent for the longer 25-mer. We interpret these results as follows. When ssDNA is immobilized at high concentration on the PtNPs, the surface sites on the NP required for electrocatalytic N2H4 oxidation are blocked. This leads to lower and fewer ECA signals. In contrast, naked PtNPs are able to transfer electrons to UMEs having sparse coatings of ssDNA.

Fabrication of carbon, gold, platinum, silver, and mercury ultramicroelectrodes with controlled geometry

A simple, fast, and reproducible method for the fabrication of disk ultramicroelectrodes (UMEs) with controlled geometry is reported. The use of prepulled soda-lime glass capillaries allows one to bypass the irreproducible torch-sealing and experimentally challenging tip-sharpening steps used in conventional fabrication protocols. A micron-sized electroactive wire is sealed inside this capillary producing UMEs with a highly reproducible geometry. Total fabrication time (1 h) and experimental difficulty are significantly reduced. Disk UMEs with various diameters and cores were fabricated, including carbon fiber (7 and 11 μm), gold (10 and 25 μm), platinum (10 and 25 μm), silver (25 μm), and mercury (25 μm). The ratio of the insulating sheath to the electroactive core of the UMEs was 2.5-3.6. Silver UMEs were also used to produce a Ag/AgCl microreference electrode. This general fabrication method can readily be applied to other electroactive cores and could allow any research group to produce high quality disk UMEs, which are a prerequisite for quantitative scanning electrochemical microscopy.

Microstamped Petri dishes for scanning electrochemical microscopy analysis of arrays of microtissues

While scanning electrochemical microscopy (SECM) is a powerful technique for non-invasive analysis of cells, SECM-based assays remain scarce and have been mainly limited so far to single cells, which is mostly due to the absence of suitable platform for experimentation on 3D cellular aggregates or microtissues. Here, we report stamping of a Petri dish with a microwell array for large-scale production of microtissues followed by their in situ analysis using SECM. The platform is realized by hot embossing arrays of microwells (200 μm depth; 400 μm diameter) in commercially available Petri dishes, using a PDMS stamp. Microtissues form spontaneously in the microwells, which is demonstrated here using various cell lines (e.g., HeLa, C2C12, HepG2 and MCF-7). Next, the respiratory activity of live HeLa microtissues is assessed by monitoring the oxygen reduction current in constant height mode and at various distances above the platform surface. Typically, at a 40 μm distance from the microtissue, a 30% decrease in the oxygen reduction current is measured, while above 250 μm, no influence of the presence of the microtissues is detected. After exposure to a model drug (50% ethanol), no such changes in oxygen concentration are found at any height in solution, which reflects that microtissues are not viable anymore. This is furthermore confirmed using conventional live/dead fluorescent stains. This live/dead assay demonstrates the capability of the proposed approach combining SECM and microtissue arrays formed in a stamped Petri dish for conducting cellular assays in a non-invasive way on 3D cellular models.

Step-scan IR spectroelectrochemistry with ultramicroelectrodes: nonsurface enhanced detection of near femtomole quantities using synchrotron radiation

The result of interfacing step-scan spectroelectrochemistry with an IR microscope and synchrotron infrared (SIR) radiation is provided here. An external reflectance cell containing a 25 μm gold ultramicroelectrode is employed to achieve an electrochemical time constant less than one microsecond. The use of a prototypical electrochemical system, i.e., the mass-transport controlled reduction of ferricyanide, allows for a proof of principle evaluation of the viability of SIR for step-scan spectroelectrochemistry. An analysis of the importance of accounting for synchrotron source variation over the prolonged duration of a step-scan experiment is provided. Modeling of the material flux in the restricted diffusion space afforded by the external reflectance cell allows the quantitative IR results to be compared to theoretical predictions. The results indicate that only at very short times does linear diffusion within the cavity dominate the electrode response and the majority of the transient signal operates under conditions of quasi-hemispherical diffusion. The analytical information provided by the IR signal is found to be considerably less than that derived from the current response due the latter's pronounced edge effects. The results provide a detection limit of 36 fmol for step-scan SIR measurements of ferrocyanide. Implications for future IR spectroelectrochemical studies in the microsecond domain are discussed.

New approach to electrode kinetic measurements in square-wave voltammetry: amplitude-based quasireversible maximum

The influence of the potential pulse height of square-wave voltammetry (SWV) (i.e., the SW amplitude) is studied for a variety of quasireversible electrode mechanisms, including a simple solution-phase electrode reaction at a planar or spherical electrode, a solution phase electrode reaction coupled with a reversible follow-up chemical reaction, and a diffusionless surface confined electrode reaction. The electrode kinetics of all the electrode mechanisms depends critically on the SW amplitude, and the quasireversible kinetic region is a function of both frequency-related electrode kinetic parameters and the SW amplitude. Thus, a novel methodology for electrode kinetics measurements is proposed by altering the SW amplitude only, at a fixed frequency of the SW potential modulation, that is, at a constant scan rate of the voltammetric experiment. Electrode kinetic measurements at a constant SW frequency are of exceptional importance especially when complex electrode mechanisms are studied, which depend on several frequency-related kinetic parameters. The electrode kinetic measurements are based on a novel feature termed the "amplitude-based quasireversible maximum", manifested as a parabolic dependence of the amplitude-normalized net SW peak current versus the SW amplitude. The position of the amplitude-based quasireversible maximum depends on the standard rate constant of the electrode reaction, enabling estimation of this important kinetic parameter in a simple and fast procedure. The novel quasireversible maximum is attributed to all studied electrode mechanisms, implying that it is a general feature of most electrode mechanisms under conditions of SWV.

Kinetics of interfacial electron transfer at single-layer graphene electrodes in aqueous and nonaqueous solutions

We present a catalog of electron transfer mediators for investigating the heterogeneous electron transfer kinetics of large-area, single-layer graphene electrodes. Scanning electrochemical microscopy (SECM) was used to probe the apparent standard electron transfer rate constant of mediators in aqueous solutions and in acetonitrile and dimethylformamide, allowing for studies of graphene electroactivity at different potentials and in both aqueous and nonaqueous media. In aqueous solution, iron(III) ethylenediaminetetraacetic acid, hexacyanoruthenate(II), hexacyanoferrate(II), hexacyanoferrate(III), octacyanomalybdate(IV), cobalt(III) sepulchrate, and hydroxymethylferrocene exhibited quasi-reversible electron transfer behavior. The electron transfer kinetics of hexaammineruthenium(III), methyl viologen, and tris(2,2'-bipyridyl)ruthenium(II) were found to be reversible in these studies. The electron transfer rate constant of hydroxymethylferrocene and ferrocene, in organic media, was similar to that for hydroxymethylferrocene in water, which, although fast, shows clear kinetic complications that we believe are inherent to graphene. A series of viologens, known to be reversible at metal electrodes, exhibited quasi-reversible electron transfer. For [Co(dapa)(2)](2+), where dapa is 2,6-bis[1-(phenylimino)ethyl]pyridine, in dimethylformamide, the oxidation state of the redox pair investigated affected the observed kinetics. Under similar experimental conditions, the Co(I/II) couple exhibited nearly reversible behavior whereas Co(II/III) had finite kinetics. This behavior was ascribed to the large difference in self-exchange rates for these two processes. To demonstrate the utility of using these mediators for examining graphene electrodes, the kinetics of two mediators with quasi-reversible electron transfer behavior, iron ethylenediaminetetraacetic acid and hexacyanoruthenate, were measured in the presence of a redox-active species [Os(bpy)(2)(dipy)Cl]PF(6), where bpy is 2,2'-bipyridine and dipy is 4,4'-trimethylenedipyridine, adsorbed onto the graphene surface. The kinetics of both mediators were enhanced in the presence of one-hundredth of a monolayer of the osmium complex, showing that even small amounts of impurities on the graphene surface are capable of enhancing the observed kinetics.

An exchangeable-tip scanning probe instrument for the analysis of combinatorial libraries of electrocatalysts

A combined scanning differential electrochemical mass spectrometer (SDEMS)-scanning electrochemical microscope (SECM) apparatus is described. The SDEMS is used to detect and spatially resolve volatile electrochemically generated species at the surface of a substrate electrode. The SECM can electrochemically probe the reactivity of the surface and also offers a convenient means of leveling the sample. It is possible to switch between these two different scanning tips and techniques without moving the sample and while maintaining potential control of the substrate electrode. A procedure for calibration of the SDEMS tip-substrate separation, based upon the transit time of electrogenerated species from the substrate to the tip is also described. This instrument can be used in the characterization of combinatorial libraries of direct alcohol fuel cell anode catalysts. The apparatus was used to analyze the products of methanol oxidation at a Pt substrate, with the SDEMS detecting carbon dioxide and methyl formate, and a PtPb-modified Pt SECM tip used for the selective detection of formic acid. As an example system, the electrocatalytic methanol oxidation activity of a sputter-deposited binary PtRu composition spread in acidic media was analyzed using the SDEMS. These results are compared with those obtained from a pH-sensitive fluorescence assay.

New chemical insights using weakly supported voltammetry: the reductive cleavage of Aryl-Br bonds is reversible

Cyclic voltammetry carried out at a wide range of supporting electrolyte concentrations and compositions can elucidate additional kinetic and mechanistic details of the electrochemical reduction of aryl halides. The cleavage of the C-Br bond is reversible, driven by H abstraction and the second electron transfer. This is a new chemical insight, as the cleavage of such bonds has usually been regarded as irreversible.

Use of hg-electroplated-pt ultramicroelectrode for determining elemental sulphur in naphtha samples

This paper describes the applicability of a Hg-electroplated-Pt ultramicroelectrode in the quantification of elemental sulphur in naphtha samples by square-wave voltammetry. A reproducible deposition methodology was studied and is reported in this paper. This methodology is innovative and relies on the quality of the mercury stock solution to obtain reproducible surfaces required for the analytical methodology. All analyses were performed using a Hg-electroplated-Pt ultramicroelectrode (Hg-Pt UME) due to the low sensibility of such devices to ohmic drops in resistive solutions. The responses of the peak areas in voltammetric experiments were linear in all of the range studied. The method developed here is accurate and reproducible, with a detection limit of 0.010 mg L(-1) and a good recovery range for both standard solutions of elemental sulphur (85 to 99%) and real naphtha sample (79%). These results attest to the potential for the application of this electroanalytical methodology in determining elemental sulphur in naphtha samples containing mercaptans and disulphides.

New chemical insights using weakly supported voltammetry: ion pairing in the EC2 reduction of 2,6-diphenylpyrylium in acetonitrile

Pairing effect: Varying the concentration of support electrolyte in the electrochemical EC(2) reduction of 2,6-diphenylpyrylium reveals the presence of ion pairing between the electroactive species and BF(4)(-). Experiment and theory are shown to be in good agreement only if ion pairing is included in the simulations. This previously unanticipated effect is only observable if voltammetry is performed under conditions of weak support.