An aptamer-based protein biochip

Microscale, Electrochemical, Aptamer-Based Sensors for Enhanced Small-Molecule Detection at Millisecond Time Scales

Microscale electrodes offer the advantages of increased mass transport rates, high sensitivity, and rapid measurement capabilities. Fabricating electrochemical aptamer-based (E-AB) sensors on these electrode platforms opens new applications to chemical and biological sensing but has remained challenging due to low signal-to-noise ratios and monolayer instability. In this article, we report the development and characterization of E-AB sensors on a gold microelectrode platform (∼500 nm radius). To overcome the small current response, we modified the electrodes by growing nanostructures via electrodeposition. We interrogated the sensors with two different electroanalytical techniques, square wave voltammetry (SWV) and intermittent pulse voltammetry (IPA), to measure the representative response of an ATP sensor and determine aptamer-target binding and dissociation time scales. We find robust and stable sensor performance with an increased response rate over sensors fabricated on macroscale electrodes. These results demonstrate that sensors developed on this microelectrode platform can be employed for enhanced spatiotemporal resolution measurements in chemical and biological environments.

Recent Advances in Surface Plasmon Resonance Sensors for Sensitive Optical Detection of Pathogens

The advancement of science and technology has led to the recent development of highly sensitive pathogen biosensing techniques. The effective treatment of pathogen infections requires sensing technologies to not only be sensitive but also render results in real-time. This review thus summarises the recent advances in optical surface plasmon resonance (SPR) sensor technology, which possesses the aforementioned advantages. Specifically, this technology allows for the detection of specific pathogens by applying nano-sized materials. This review focuses on various nanomaterials that are used to ensure the performance and high selectivity of SPR sensors. This review will undoubtedly accelerate the development of optical biosensing technology, thus allowing for real-time diagnosis and the timely delivery of appropriate treatments as well as preventing the spread of highly contagious pathogens.

Aptamers against Immunoglobulins: Design, Selection and Bioanalytical Applications

Nucleic acid aptamers show clear promise as diagnostic reagents, as highly specific strands were reported against a large variety of biomarkers. They have appealing benefits in terms of reproducible generation by chemical synthesis, controlled modification with labels and functionalities providing versatile means for detection and oriented immobilization, as along with high biochemical and temperature resistance. Aptamers against immunoglobulin targets-IgA, IgM, IgG and IgE-have a clear niche for diagnostic applications, therefore numerous aptamers have been selected and used in combination with a variety of detection techniques. The aim of this review is to overview and evaluate aptamers selected for the recognition of antibodies, in terms of their design, analytical properties and diagnostic applications. Aptamer candidates showed convincing performance among others to identify stress and upper respiratory tract infection through SIgA detection, for cancer cell recognition using membrane bound IgM, to detect and treat hemolytic transfusion reactions, autoimmune diseases with IgG and detection of IgE for allergy diseases. However, in general, their use still lags significantly behind what their claimed benefits and the plethora of application opportunities would forecast.

Sensitive and specific detection of proteins based on target-responsive DNA polymerase activity

We herein describe a novel method for the detection of target protein based on the target-responsive DNA polymerase activity. In the sensor, two different types of DNA aptamers with the respective functions: one binds to the target protein and the other binds to DNA polymerase, are rationally engineered and combined to form the detection probe that regulates DNA polymerase activity in response to the target protein. In the presence of target protein, the detection probe becomes destabilized and stops the inhibition of DNA polymerase activity. Consequently, the active DNA polymerase initiates the primer extension reaction on the target-specific DNA aptamer, which recycles the target protein to promote another activation cycle of DNA polymerase. In addition, DNA polymerase also catalyzes the primer extension reaction on the primer/template complex in conjugation with TaqMan probe, leading to the significantly enhanced fluorescence intensities. With this novel strategy, we detected a model target protein, lysozyme with a limit of detection as low as 0.80 nM. In addition, the practical applicability of this system was successfully demonstrated by determining lysozyme in human serum.

Aptamers, antibody scFv, and antibody Fab' fragments: An overview and comparison of three of the most versatile biosensor biorecognition elements

The choice of biosensing elements is crucial for the development of the optimal biosensor. Three of the most versatile biosensing elements are antibody single-chain Fv fragments (scFv), antibody fragment-antigen binding (Fab') units, and aptamers. This article provides an overview of these three biorecognition elements with respects to their synthesis/engineering, various immobilization techniques, and examples of their use in biosensors. Furthermore, the final section of the review compares and contrasts their characteristics (time/cost of development, ease and variability of immobilization, affinity, stability) illustrating their advantages and disadvantages. Overall, scFv fragments are found to display the highest customizability (i.e. addition of functional groups, immobilizing peptides, etc.) due to recombinant synthesis techniques. If time and cost are an issue in the development of the biosensor, Fab' fragments should be chosen as they are relatively cheap and can be developed quickly from whole antibodies (several days). However, if there are sufficient funds and time is not a factor, aptamers should be utilized as they display the greatest affinity towards their target analytes and are extremely stable (excellent biosensor regenerability).

Aptamers-based sandwich assay for silver-enhanced fluorescence multiplex detection

In this work, aptamers-modified silver nanoparticles (AgNPs) were prepared as capture substrate, and fluorescent dyes-modified aptamers were synthesized as detection probes. The sandwich assay was based on dual aptamers, which was aimed to accomplish the highly sensitive detection of single protein and multiplex detection of proteins on one-spot. We found that aptamers-modified AgNPs based microarray was much superior to the aptamer based microarray in fluorescence detection of proteins. The result shows that the detection limit of the sandwich assay using AgNPs probes for thrombin or platelet-derived growth factor-BB (PDGF-BB) is 80 or 8 times lower than that of aptamers used directly. For multiplex detection of proteins, the detection limit was 625 pM for PDGF-BB and 21 pM for thrombin respectively. The sandwich assay based on dual aptamers and AgNPs was sensitive and specific.

Aptamers Against Immunologic Targets: Diagnostic and Therapeutic Prospects

The concept of in vitro selection of nucleic acid aptamers emerged 25 years ago, and since then tremendous progress has been achieved in the development of different aptamers and their applications for various bioanalytical and therapeutic purposes. Among other protein targets of aptamers, immune system proteins are of particular interest both as diagnostic markers and therapeutic targets. The present review summarizes up-to-date articles concerning the selection and design of DNA and RNA aptamers against immunologic targets such as antibodies, cytokines, and T-cell and B-cell receptors. We also discuss the prospects of employing aptamers as recognizing modules of diagnostic aptasensors, potential therapeutic candidates for the treatment of autoimmune diseases and cancer, and specific tools for functional studies of immune system proteins.

Quencher-free molecular aptamer beacons (QF-MABs) for detection of ATP

We have constructed a simple and efficient system-based on quencher-free molecular aptamer beacons (QF-MABs)-for probing ATP. In the absence of ATP, the fluorescence of a pyrene fluorophore on the loop position (15 nucleotides from the 5' end) of the optimal QF-MAB was quenched by the neighboring nucleobases; in its presence, fluorescence was recovered, due to a conformational change in the secondary structure of the QF-MAB.

A highly selective and sensitive cocaine aptasensor based on covalent attachment of the aptamer-functionalized AuNPs onto nanocomposite as the support platform

Based on the conformational changes of the aptamer-functionalized gold nanoparticles (AuNPs) onto MWCNTs/IL/Chit nanocomposite as the support platform, we have developed a sensitive and selective electrochemical aptasensor for the detection of cocaine. The 5'-amine-3'-AuNP terminated aptamer is covalently attached to a MWCNTs/IL/Chit nanocomposite. The interaction of cocaine with the aptamer functionalized AuNP caused the aptamer to be folded and the AuNPs with negative charge at the end of the aptamer came to the near of electrode surface therefore, the electron transfer between ferricyanide (K3Fe(CN)6) as redox probe and electrode surface was inhibited. A decreased current of (K3Fe(CN)6) was monitored by differential pulse voltammetry technique. In an optimized condition the calibration curve for cocaine concentration was linear up to 11 μM with detection limit (signal-to-noise ratio of 3) of 100 pM. To test the selectivity of the prepared aptasensor sensing platform applicability, some analgesic drugs as the interferes were examined. The potential of the aptasensor was successfully applied for measuring cocaine concentration in human blood serum. Based on our experiments it can be said that the present method is absolutely beneficial in developing other electrochemical aptasensor.

A colorimetric sandwich-type assay for sensitive thrombin detection based on enzyme-linked aptamer assay

A colorimetric sandwich-type assay based on enzyme-linked aptamer assay has been developed for the fast and sensitive detection of as low as 25 fM of thrombin with high linearity. Aptamer-immobilized glass was used to capture the target analyte, whereas a second aptamer, functionalized with horseradish peroxidase (HRP), was employed for the conventional 3,5,3',5'-tetramethylbenzidine (TMB)-based colorimetric detection. Without the troublesome antibody requirement of the conventional enzyme-linked immunosorbent assay (ELISA), as low as 25 fM of thrombin could be rapidly and reproducibly detected. This assay has superior, or at least equal, recovery and accuracy to that of conventional antibody-based ELISA.

Highly selective and sensitive adenosine aptasensor based on platinum nanoparticles as catalytical label for amplified detection of biorecognition events through H2O2 reduction

Based on a combination of aptamer and platinum nanoparticles a new sensitive and selective adenosine aptasensor was fabricated. Functionalized thiol-terminated adenosine aptamer (5'-AGAGAACCTGGGGGAGTATTGCGGAGGAAGGT-SH-3') with Pt Nanoparticles (Pt-NPs) was employed as highly catalytic label for electrochemical detection of adenosine based on electrocatalytic activity of Pt-NPs toward H2O2 reduction. Multiwalled carbon nanotubes/ionic liquid/chitosan (MWCNTs/IL/CHIT) nanocomposite was applied as the interface for covalent attachment of 3'-amine-terminated capture probe (3'-NH2-(CH2)6-TCTCTTGGACCC-5'). The presence of Pt nanoparticles improvement the conductivity and performance characteristics of the biosensor as well as incensement in the loading amount of the aptamer DNA sequence. The interaction of adenosine with the aptamer causes the releasing of aptamer with PtNPs into solution which resulted in a decreasing of hydrogen peroxide reduction peak current. Sensitive quantitative detection of adenosine was achieved by monitoring the decrease of voltammetric responses of H2O2 peak current. The peak current of H2O2 decreased with increase in the concentration of adenosine over a range of 1-750 nM with detection limit 1 nM. In addition the proposed aptasensor showed excellent selectivity toward adenosine in compared to some other nucleosides such as guanosine, cytidine and uridine. The proposed aptasensor was successfully used to detect adenosine in human serum samples. The elimination of enzymes or antibodies for the amplified detection of adenosine and the use of platinum nanoparticles as inorganic catalytic label, are the advantage of the proposed aptasensor.

Determination of L-argininamide based on water-soluble fluorescent conjugated polymer-aptamer

Water-soluble fluorescent conjugated polymer is a promising material which could be used as an optical platform in highly sensitive molecular sensors. In this paper, a simple label-free DNA sensor, which consisted of a poly(3-alkoxy-4-methylthiophene) and an aptamer, was used to detect L-argininamide (L-Arm). Due to the specific binding reaction between L-Arm and its aptamer, the proposed method can easily determinate the L-Arm through the recovery of fluorescence without any modification. Other ions or similar molecules had little effect on the detection. Moreover, there was a linear relationship between fluorescence intensity and the concentration of L-Arm. The detection limit of L-Arm was as low as 4.7 nM.

Determination of fructose 1,6-bisphosphate using a double-receptor sandwich type fluorescence sensing method based on uranyl-salophen complexes

In this paper, we report a double-receptor sandwich type fluorescence sensing method for the determination of fructose bisphosphates (FBPs) using fructose 1,6-bisphosphate (F-1,6-BP) as a model analyte based on uranyl-salophen complexes. The solid phase receptor is an immobilized uranyl-salophen (IUS) complex which is bound on the surface of glass slides by covalent bonds. The labeled receptor is another uranyl-salophen complex containing a fluorescence group, or uranyl-salophen-fluorescein (USF). In the procedure of determining F-1,6-BP in sample solution, F-1,6-BP is first adsorbed on the surface of the glass slide through the coordination reaction of F-1,6-BP with IUS. It then binds USF through another coordination reaction to form a sandwich-type structure of IUS-F-1,6-BP-USF. The amount of F-1,6-BP is detected by the determination of the fluorescence intensity of IUS-F-1,6-BP-USF bound on the glass slide. Under optimal conditions, the linear range for the detection of F-1,6-BP is 0.05-5.0 nmol mL(-1) with a detection limit of 0.027 nmol mL(-1). The proposed method has been successfully applied for the determination of F-1,6-BP in real samples with satisfactory results.

An overview of transducers as platform for the rapid detection of foodborne pathogens

The driving advent of portable, integrated biosensing ways for pathogen detection methods offers increased sensitivity and specificity over traditional microbiological techniques. The miniaturization and automation of integrated detection systems present a significant advantage for rapid, portable detection of foodborne microbes. In this review, we have highlighted current developments and directions in foodborne pathogen detection systems. Recent progress in the biosensor protocols toward the detection of specific microbes has been elaborated in detail. It also includes strategies and challenges for the implementation of a portable platform toward rapid foodborne sensing systems.

Selective and quantitative cell detection based both on aptamers and the conventional cell-staining methods

Aptamer-based biochips for selective cell detection and quantitation in combination of the recent biochip technology and the conventional cell staining methods are described. Using a model system comprising HER2- or PSMA-positive cells as the analytes and single-stranded RNA aptamers specific for HER2 or PSMA as immobilized ligands on chips, we could demonstrate that aptamers were equivalent or superior to antibodies in terms of specificity and sensitivity, respectively. In particular, our PSMA-specific sensor was found to have the characteristics of good stability, reproducibility and reusability, with detection limit as low as 10(3) LNCaP cells. In conclusion, we could show the suitability of nucleic acid aptamers as low molecular weight receptors on biochips for sensitive and specific cell detection and quantitation for future diagnostics development.

An aptamer-based biosensing platform for highly sensitive detection of platelet-derived growth factor via enzyme-mediated direct electrochemistry

In this work, a new label-free electrochemical aptamer-based sensor (aptasensor) was constructed for detection of platelet-derived growth factor (PDGF) based on the direct electrochemistry of glucose oxidase (GOD). For this proposed aptasensor, poly(diallyldimethylammonium chloride) (PDDA)-protected graphene-gold nanoparticles (P-Gra-GNPs) composite was firstly coated on electrode surface to form the interface with biocompatibility and huge surface area for the adsorption of GOD layer. Subsequently, gold nanoclusters (GNCs) were deposited on the surface of GOD to capture PDGF binding aptamer (PBA). Finally, GOD as a blocking reagent was employed to block the remaining active sites of the GNCs and avoid the nonspecific adsorption. With the direct electron transfer of double layer GOD membranes, the aptasensor showed excellent electrochemical response and the peak current decreased linearly with increasing logarithm of PDGF concentration from 0.005 nM to 60 nM with a relatively low limit of detection of 1.7 pM. The proposed aptasensor exhibited high specificity, good reproducibility and long-term stability, which provided a new promising technique for aptamer-based protein detection.

An electronic channel switching-based aptasensor for ultrasensitive protein detection

Due to the ubiquity and essential of the proteins in all living organisms, the identification and quantification of disease-specific proteins are particularly important. Because the conformational change of aptamer upon its target or probe/target/probe sandwich often is the primary prerequisite for the design of an electrochemical aptameric assay system, it is extremely difficult to construct the electrochemical aptasensor for protein assay because the corresponding aptamers cannot often meet the requirement. To circumvent the obstacles mentioned, an electronic channel switching-based (ECS) aptasensor for ultrasensitive protein detection is developed. The essential achievement made is that an innovative sensing concept is proposed: the hairpin structure of aptamer is designed to pull electroactive species toward electrode surface and makes the surface-immobilized IgE serve as a barrier that separates enzyme from its substrate. It seemingly ensures that the ECS aptasensor exhibits most excellent assay features, such as, a detection limit of 4.44×10(-6)μg mL(-1) (22.7fM, 220zmol in 10-μL sample) (demonstrating a 5 orders of magnitude improvement in detection sensitivity compared with classical electronic aptasensors) and dynamic response range from 4.44×10(-6) to 4.44×10(-1)μg mL(-1). We believe that the described sensing concept here might open a new avenue for the detection of proteins and other biomacromolecules.

Biosensors - classification, characterization and new trends

Biosensors represent promising analytical tools applicable in areas such as clinical diagnosis, food industry, environment monitoring and in other fields, where rapid and reliable analyses are needed. Some biosensors were successfully implemented in the commercial sphere, but majority needs to be improved in order to overcome some imperfections. This review covers the basic types, principles, constructions and use of biosensors as well as new trends used for their fabrication.

Highly sensitive detection of platelet-derived growth factor on a functionalized diamond surface using aptamer sandwich design

Aptamer-based fluorescence detection of platelet-derived growth factor (PDGF) on a functionalized diamond surface was demonstrated. In this work, a sandwich design based on the ability of PDGF to bind with aptamers at its two available binding sites was employed. It was found that this sandwich design approach significantly increases the fluorescence signal intensity, and thereby a very low detection limit of 4 pM was achieved. The effect of the ionic strength of MgCl(2) buffer solution was also investigated, and the most favourable binding for PDGF-BB occurred at a Mg(2+) concentration of 5.5 mM. Since the aptamers bind to the target PDGF with high affinity, fluorescence detection exhibited high selectivity towards different biomolecules. The high reproducibility of detection was confirmed by performing three cycles of measurements over a period of three days.

Metal-enhanced fluorescent probes based on silver nanoparticles and its application in IgE detection

In this paper, a novel metal plasmon coupled with an aptamer-nucleotide hybridized probe was fabricated and applied for protein detection. The specific aptamer and single-strand oligonucleotide were chemically bound to silver nanoparticles (AgNPs), and Cy5-labeled, complementary single-strand oligonucleotides were hybridized with the particle-bound oligonucleotides. The hybridized DNA duplexes were regarded as rigid rods that separated the fluorophore Cy5 and the surface of AgNPs to reduce the competitive quenching. Using a model system comprising human immunoglobulin E (IgE) as the analyte and goat antihuman IgE as immobilized capture antibody on glass slides, we demonstrate that the detection performance of the synthetic probe was superior to the aptamer-based fluorescent probes. The results showed a good linear correlation for human IgE in the range from 10 ng/ml to 6.25 μg/ml. The detection limit obtained was 1 ng/ml, which was 50 times lower than that using Cy5 oligonucleotide/aptamer hybrid duplex (Probe2) due to the metal-enhanced fluorescence effect. This new strategy opens the possibility for the preparation of high-sensitivity detection probes based on metal nanoparticles.

Aptamer-functionalized microgel particles for protein detection

Highly sensitive and multiplexed detection of clinically relevant proteins in biologically complex samples is crucial for the advancement of clinical proteomics. In recent years, aptamers have emerged as useful tools for protein analysis due to their specificity and affinity for protein targets as well as their compatibility with particle-based detection systems. In this study, we demonstrate the highly sensitive detection of human α-thrombin on encoded hydrogel microparticles functionalized with an aptamer capture sequence. We use static imaging and microfluidic flow-through analysis techniques to evaluate the detection capabilities of the microgels in sandwich-assay formats that utilize both aptamers and antibodies for the reporting of target-binding events. Buffers and reagent concentrations were optimized to provide maximum reaction efficiency while still maintaining an assay with a simple workflow that can be easily adapted to the multiplexed detection of other clinically relevant proteins. The three-dimensional, nonfouling hydrogel immobilization scaffold used in this work provides three logs of dynamic range, with a limit of detection of 4 pM using a single aptamer capture species and without the need for spacers or signal amplification.

Fluorescence enhancement of silver nanoparticle hybrid probes and ultrasensitive detection of IgE

An ultrasensitive protein assay method was developed based on silver nanoparticle (AgNP) hybrid probes and metal-enhanced fluorescence. Two aptamer based silver nanoparticles, Aptamer/Oligomer-A/Cy3-modified AgNPs (Tag-A) and Aptamer/Oligomer-B/Cy3-modified AgNPs (Tag-B) were hybridized to form a silver nanoparticle aggregate that produced a red shift and broadening of the Localized Surface Plasmon Resonance (LSPR) peak. The enhanced fluorescence resulted from the increased content of Cy3 molecules and their emission resonance coupled to the broadened localized surface plasmon (LSP) of AgNP aggregate. The separation distance between Cy3 and AgNPs was 8 nm which was the most optimal for metal enhanced fluorescence and the separation distance between adjacent AgNPs was about 16 nm and this was controlled by the lengths of oligomer-A and oligomer-B. The protein array was prepared by covalently immobilizing capture antibodies on aldehyde-coated slide. After addition of protein IgE sample, two kinds of aptamer-modified AgNPs (Tag-A and Tag-B) were employed to specifically recognize IgE and form the AgNP aggregate on the arrays based on their hybridization. The detection property of the aptamer-modified AgNP aggregate was compared to two other modified aptamer-based probes, aptamer-modified Cy3 and Tag-A. The modified AgNP hybrid probe (Tag-A and Tag-B) showed remarkable superiority in both sensitivity and detection limit due to the formed AgNP aggregate. The new hybrid probe also produced a wider linear range from 0.49 to 1000 ng/mL with the detection limit reduced to 40 pg/mL (211 fM). The presented method showed that the newly designed strategy of combining aptamer-based nanomaterials to form aggregates results in a highly sensitive optical detection method based on localized surface plasmon.

Continuous signal enhancement for sensitive aptamer affinity probe electrophoresis assay using electrokinetic concentration

We describe an electrokinetic concentration-enhanced aptamer affinity probe electrophoresis assay to achieve highly sensitive and quantitative detection of protein targets in a microfluidic device. The key weaknesses of aptamer as a binding agent (weak binding strength/fast target dissociation) were counteracted by continuous injection of fresh sample while band-broadening phenomena were minimized due to self-focusing effects. With 30 min of continuous signal enhancement, we can detect 4.4 pM human immunoglobulin E (IgE) and 9 pM human immunodeficiency virus 1 reverse transcriptase (HIV-1 RT), which are among the lowest limits of detection (LOD) reported. IgE was detected in serum sample with a LOD of 39 pM due to nonspecific interactions between aptamers and serum proteins. The method presented in this paper also has broad applicability to improve sensitivities of various other mobility shift assays.

Aptameric system for the highly selective and ultrasensitive detection of protein in human serum based on non-stripping gold nanoparticles

A novel approach is proposed in this study for the development of an aptameric assay system for protein based on non-stripping gold nanoparticles (NPs)-triggered chemiluminescence (CL) upon target binding. The strategy chiefly depends on the formation of a sandwich-type immunocomplex among the capture antibody immobilized on the polystyrene microwells, target protein and aptamer-functionalized gold NPs. Introduction of target protein into the assay system leads to the attachment of gold NPs onto the surface of the microwells and thus the assembled gold NPs could trigger the reaction between luminol and AgNO(3) with a CL emission. Further signal amplification was achieved by a simple gold metal catalytic deposition onto the gold NPs. Such an amplified CL transduction allowed for the detection of model target IgE down to the 50 fM, which is better than most existing aptameric methods for IgE detection. This new protocol also provided a good capability in discriminating IgE from nontarget proteins such as IgG, IgA, IgM and interferon. The practical application of the proposed gold NPs-based immunoassay was successfully carried out for the determination of IgE in 35 human serum samples. Overall, the proposed assay system exhibits excellent analytical characteristics (e.g., a detection limit on the attomolar scale and a linear dynamic range of 4 orders of magnitude), and it is also straightforward to adapt this strategy to detect a spectrum of other proteins by using different aptamers. This new CL strategy might create a novel technology for developing simple biosensors in the sensitive and selective detection of target protein in a variety of clinical, environmental and biodefense applications.

Time-resolved fluorescence biosensor for adenosine detection based on home-made europium complexes

In this protocol, the authors report a time-resolved fluorescence biosensor based on home-made europium complexes for highly sensitive detection of small molecules using adenosine as a model analyte. The fluorophore that used is europium complexes. Its signal can be measured in a time-resolved manner that eliminates most of the unspecific fluorescent background. The amino modified aptamer probe, which is designed to specifically recognize adenosine, is combined to the aldehyde-group modified glass slide by covalent bond. Europium complex-labeled a short ssDNA, designed to segment hybridize with aptamer probe is immobilized on the glass slide by hybridization reaction. In the presence of adenosine, the aptamer part is more inclined to bounds with adenosine and triggers structure-switching of the aptamer from aptamer/ssDNA duplex to aptamer/target complex. As a result, europium complexes-labeled ssDNA is forced to dissociate from the sensor interface, resulting in time-resolved fluorescence intensity decrease. The decrement intensity is proportional to the amount of adenosine. Under optimized assay conditions, a linear range (1.0×10(-8)M to 1.0×10(-7)M) is got with low detection limit of 5.61nM. The biosensor exhibits excellent selectivity and can provide a promising potential for aptamer-based adenosine detection.

Highly sensitive electrochemical label-free aptasensor based on dual electrocatalytic amplification of Pt-AuNPs and HRP

In this work, a label-free electrochemical aptamer-based sensor (aptasensor) was constructed on account of the direct immobilization of redox probes on an electrode surface. For this proposed aptasensor, a gold nanoparticles (AuNPs)-coated electrode was firstly modified with redox probes-nickel hexacyanoferrates nanoparticles (NiHCFNPs) through chemisorption and electrostatic adsorption. Then, platinum-gold alloy nanoparticles (Pt-AuNPs) and horseradish peroxidase (HRP) were respectively assembled onto the modified electrode surface, which formed the multilayer films for amplifying the electrochemical signal of NiHCFNPs and immobilizing thiolated thrombin aptamers (TBAs). In the presence of target thrombin, the TBA on the multilayer could catch the thrombin onto the electrode surface, which resulted in a barrier for electro-transfer, leading to the decrease of the electrochemical signal of NiHCFNPs amplified by the Pt-AuNPs and HRP toward H(2)O(2). The proposed method avoided the redox probes labeling process, increased the amount of redox probes, and further amplified the electrochemical signal. Thus, the approach showed a high sensitivity and a wider linearity to thrombin in the range between 0.01 nM and 50 nM with a detection limit of 6.3 pM.

Optical detection systems using immobilized aptamers

Advances in the development and the applications of optical biosensing systems based on immobilized aptamers are presented. These nucleic acid sequences have been used as new molecular recognition elements to develop heterogeneous assays, biosensors and microarrays. Among different detection modes that have been employed, optical ones which are described here are among the most used. Since their first report in 1996, numerous optical detection systems using aptamers and mainly based on fluorescence have been developed. Two main approaches have been used: label-based (using fluorophore, luminophore, enzyme, nanoparticles) or aptamer label-free detection systems (e.g. surface plasmon resonance, optical resonance). Most methods are based on a labeling approach. Some targets can be optically detected using not only colorimetry, chemiluminescence or the most developed fluorescence mode but also more recent non conventional optical methods such as surface plasmon-coupled directional emission (SPCDE). The first SPCDE-based aptasensor for thrombin detection has recently been reported in 2009. Aptasensors based on surface-enhanced Raman scattering spectroscopy (SERS) which presents advantages compared to fluorescence have also been described. Different label-free techniques have recently been shown to be suitable for developing performant aptasensors or aptamer-based microarrays, such as surface plasmon resonance (SPR), diffraction grating, evanescent-field-coupled (EFC) waveguide-mode, optical resonance or Brewster angle straddle interferometry (BASI). Important advances have been realized on optical aptamer-based detection systems that appear as highly efficient devices with enormous potential.

Microarray bioinformatics

Bioinformatics has become an increasingly important tool for molecular biologists, especially for the analysis of microarray data. Microarrays can produce vast amounts of information requiring a series of consecutive analyses to render the data interpretable. The direct output of microarrays cannot be directly interpreted to show differences in settings, conditions of samples, or time points. To make microarray experiments interpretable, it is necessary that a series of algorithms and approaches be applied. After normalization of generated data, which is necessary to make a comparison feasible, significance analysis, clustering of samples and biological compounds of interest and visualization are generally performed. This chapter will focus on providing a basic understanding of the generally approaches and algorithms currently employed in microarray bioinformatics.

Electrochemical impedance spectroscopy detection of lysozyme based on electrodeposited gold nanoparticles

A simple, highly sensitive, and label-free electrochemical impedance spectroscopy (EIS) aptasensor based on an anti-lysozyme-aptamer as a molecular recognition element, was developed for the detection of lysozyme. Improvement in sensitivity was achieved by utilizing gold nanoparticles (AuNPs), which were electrodeposited onto the surface of a gold electrode, as a platform for immobilization of the aptamer. To quantify the amount of lysozyme, changes in the interfacial electron transfer resistance (R(et)) of the aptasensor were monitored using the redox couple of an [Fe(CN)(6)](3-/4-) probe. The R(et) increased with lysozyme concentration. The plot of R(et) against the logarithm of lysozyme concentration is linear over the range from 0.1 pM to 500 pM with a detection limit of 0.01 pM. The aptasensor also showed good selectivity for lysozyme without being affected by the presence of other proteins.

Aptamer-barcode based immunoassay for the instantaneous derivatization chemiluminescence detection of IgE coupled to magnetic beads

We report on a highly sensitive aptameric assay system for the determination of IgE, where a special chemiluminescence (CL) reagent, 3,4,5-trimethoxylphenylglyoxal (TMPG), acts as the signaling molecule and polystyrene beads as the amplification platform. Briefly, a "sandwich-type" detection strategy is employed in our design, where magnetic beads functionalized with a capture antibody were reacted with the target protein IgE, and then sandwiched with the aptamer-barcodes which were prepared by assembling polystyrene beads with IgE aptamer. The target immunoreaction event could be sensitively detected via an instantaneous derivatization reaction between TMPG and the guanine (G) nucleotides within the aptamer-barcodes to form an unstable CL intermediate for the generation of light. Further signal amplification is achieved by extending the G nucleotide-rich domain on the aptamer backbone for second amplification. Such simple amplified CL transduction allows the detection of IgE down to the 4.6 pM level, which is better than most previous aptameric methods for IgE detection. This new protocol also provides a good capability in discriminating IgE from nontarget proteins such as IgG, IgA, IgM, interferon and thrombin. The practical application of the proposed aptamer-barcode based immunoassay was successfully carried out for the determination of IgE in 20 human serum samples. It is straightforward to adapt this strategy to detect a spectrum of other proteins by using different aptamers, thus this method may offer a new direction in designing high-performance CL aptasensors for early diagnoses of diseases.

Time-resolved fluorescence aptamer-based sandwich assay for thrombin detection

In the present study, the authors report a novel sensitive method for the detection of thrombin using time-resolved fluorescence sensing platform based on two different thrombin aptamers. The thrombin 15-mer aptamer as a capture probe was covalently attached to the surface of glass slide, and the thrombin 29-mer aptamer was fluorescently labeled as a detection probe. A bifunctional europium complex was used as the fluorescent label. The introduction of thrombin triggers the two different thrombin aptamers and thrombin to form a sandwich structure. The fluorescence intensity is proportional to the thrombin concentration. The present sensing system could provide both a wide linear dynamic range and a low detection limit. The proposed sensing system also presented satisfactory specificity and selectivity. Results showed that thrombin was retained at the aptamer-modified glass surface while nonspecific proteins were removed by rinsing with buffer solution. This approach successfully showed the suitability of aptamers as low molecular weight receptors on glass slides for sensitive and specific protein detection.

A novel separation and enrichment method of 17β-estradiol using aptamer-anchored microbeads

The estrogenic compound 17β-estradiol (E2) is widely studied for its potential endocrine disruption effects. Due to the low level of E2 present in the environment, it is highly desirable to develop a sensitive and efficient separation and enrichment method for E2 analysis. In this paper, we proposed a novel E2 preconcentration method using anti-E2 aptamer-anchored isothiocyanate-modified beads (NCS beads). The glass beads are chemically modified with primary amino group, and then treated with phenylene diisothiocyanate (PDITC) to generate an isothiocyanate group, which is reactive towards the amine group. The amino-modified anti-E2 aptamer can be easily covalently immobilized onto the as-prepared NCS beads. The experimental results demonstrated that the aptamer affinity microbeads could selectively retain and separate E2 compound. The effects of the operation parameters on retention of E2, including washing condition, eluting condition, the number of beads, and the incubation time were investigated. Moreover, high-performance liquid chromatography with preconcentration of E2 on the aptamer affinity microbeads was applied to detect the E2 in the spiked water samples and obtained a good recovery.

Development of a dual-aptamer-based multiplex protein biosensor

Parallel biosensors for proteins are becoming more essential for the thorough and systematic investigation of complex biological processes. These tools also enable improved clinical diagnoses relative to single-protein analyses due to their greater information content. If implemented correctly, affinity-based techniques can provide unique advantages in terms of sensitivity and flexibility. Aptamers are increasingly being used as the affinity reagents of choice for protein biosensing applications. Here, we describe the development and characterization of an aptamer-based method for parallel protein analyses that relies on recognition of the target protein by two unique aptamers targeting different epitopes on the protein. Our results show that the technique achieved simultaneous and quantitative detection of thrombin and platelet-derived growth factor-BB (PDGF-BB) with high specificity both in buffered solutions and in serum samples.

Enhancement of aptamer microarray sensitivity through spacer optimization and avidity effect

This work aims for ultrasensitive detection of target proteins in complex biological matrixes based on aptamer microarrays. Two extensively studied aptamers (HTQ and HTDQ) that bind distinct epitopes of thrombin are chosen for the microarray study. Although HTQ and HTDQ have nanomolar to subnanomolar affinities, it is found that either aptamer when applied directly has difficulty in detecting a few nanomoles per liter thrombin in the presence of a 10- or 100-fold (w/w) excess of serum total protein (STP). By investigating dodecyl (12-carbon) and oligodeoxythymidine (oligo(dT)) spacers, we observe both spacers enhance the microarray signal response, but oligo(dT) is strikingly better than dodecyl. Moreover, we discover that a microarray spot coprinted with the two distinct aptamers (HTQ and HTDQ) functions like a bivalent molecular construct and exhibits an avidity effect. With the synergy of oligo(dT) spacers and the avidity effect, detection of picomolar-range thrombin in the presence of either 10% unlabeled serum or a 10,000-fold excess of labeled serum total protein is achieved. It corresponds to a 100-1000-fold sensitivity enhancement as compared to using an individual aptamer without a spacer.

Aptamer-encoded nanopore for ultrasensitive detection of bioterrorist agent ricin at single-molecule resolution

The molecular-scale pore structure, called nanopore, can be formed from protein ion channels by genetic engineering or fabricated on solid substrates using fashion nanotechnology. Target molecules in interaction with the functionalized lumen of nanopore, can produce characteristic changes in the pore conductance, which act as fingerprints, allowing us to identify single molecules and simultaneously quantify each target species in the mixture. Nanopore sensors have been created for tremendous biomedical detections, with targets ranging from metal ions, drug compounds and cellular second messengers, to proteins and DNAs. Here we will review our recent discoveries with a lab-in-hand glass nanopore: single-molecule discrimination of chiral enantiomers with a trapped cyclodextrin, and sensing of bioterrorist agent ricin.

Emerging affinity-based techniques in proteomics

Proteomes of interest, such as the human proteome, have such complexity that no single technique is adequate for the complete analysis of the constituents. Depending on the goal (e.g., identification of a novel protein vs measurement of the level of a known protein), the tools required can vary significantly. While existing methods provide valuable information, their limitations drive the development of complementary, innovative methods to achieve greater breadth of coverage, dynamic range or specificity of analysis. We will discuss affinity-based methods and their applications, focusing on their unique advantages. In addition, we will describe emerging methods with potential value to proteomics, as well as the challenges that remain for proteomic studies.

Aptamers and riboswitches: perspectives in biotechnology

Aptamers are short, single stranded nucleic acids which bind a wide range of different ligands with extraordinary high binding affinity and specificity. The steadily increasing number of aptamers is accompanied by an expanding range of applications in biotechnology. We will describe new developments in the field including the use of aptamers for conditional gene regulation and as biosensors. In addition, we will discuss the potential of aptamers as tags to visualize RNA and protein distribution in living cells and as therapeutics. Furthermore, we will consider biotechnological applications of riboswitches for gene regulation and as drug target.