Development and Application of Porous Membrane-Protected Carbon Nanotube Micro-Solid-Phase Extraction Combined with Gas Chromatography/Mass Spectrometry

Extraction of Organochlorine Pesticides from Porous Membrane Packed Dried Fish Samples: Method Development and Greenness Evaluation

In this work, ultrasound-assisted solvent extraction was utilized for extraction of organochlorine pesticides from membrane-protected dried fish samples. The dried fish samples were packed inside a porous membrane bag which was immersed in a solvent and subjected to ultrasonication. After the extraction process, the sample-containing bag was separated from the extract. Since samples were packed inside the membrane, their separation did not require centrifugation or filtration. Moreover, the complex components of the biota matrix may also retain inside the porous membrane bag, alleviating the requirement of extract cleanup before analysis. The parameters that can affect the ultrasound-assisted solvent extraction of membrane-protected dried fish samples were suitably optimized. These parameters include the extraction solvent and its volume, the sample amount, ultrasound intensity and extraction time. Under the optimum extraction conditions, good linearity was achieved for all the tested organochlorine pesticides, with the coefficients of determination (R2) higher than 0.9922 for the linear ranges from 5–1000, 10–1000 and 20–1000 ng/g. The values of intra-day and inter-day relative standard deviations were ≤13.8%. The limit of detection ranged from 1.5 to 6.8 ng/g. The spiked relative recoveries were in the range of 87.3–104.2%. This method demonstrated excellent figures of merit and could find potential applications in routine analytical laboratories. Finally, the greenness of this method was evaluated using the green analytical procedure index and analytical greenness calculator metrics.

Green Analytical Toxicology for the Determination of Cocaine Metabolites

Brazil is the third largest contributor to Green Analytical Chemistry, and there is significant participation of toxicologists in the development and improvement of environmental techniques. Currently, toxicologists have their own strategies and guidelines to promote the reduction/replacement or elimination of solvents, reduce the impacts of derivatization and save time, among other objectives, due to the peculiarities of toxicological analysis. Thus, this review aims to propose the concept of Green Analytical Toxicology and conduct a discussion about its relevance and applications specifically in forensic toxicology, using the microextraction methods developed for the determination of cocaine and its metabolites as examples.

Recent advances of ordered mesoporous silica materials for solid-phase extraction

This review mainly focuses on the development and application of ordered mesoporous silica materials for solid-phase extraction in recent years. It overviews not only bare mesoporous silica but also the functionalized mesoporous silica with organic groups, molecularly imprinted polymers, and magnetic materials. These mesoporous silica materials were used as the extraction adsorbents in cartridge solid-phase extraction, dispersive solid-phase extraction, magnetic solid-phase extraction, micro-solid-phase extraction and matrix solid phase dispersion. Coupled with atomic emission spectrometry, chromatography or other detection methods, these techniques efficiently extracted and sensitively determined various targets, such as metal ions, perfluorocarboxylic acids, pesticides, drugs, endocrine disruptors, phenols, flavanones, polycyclic aromatic hydrocarbons, parabens and so on. Based on unique advantages of mesoporous silica materials, the developed analytical method successfully analyzed different matrix samples, like environmental water samples, soil samples, food samples, biological samples and cosmetics. In addition, the prospects of these materials in solid-phase extraction are presented, which can offer an outlook for the further development and applications.

A membrane-protected microsolid phase-extraction method based on molecular imprinting and its application to the determination of local anesthetics in cosmetics

As local anesthetics (LAs) that are illegally added into cosmetics are harmful to consumer health, it is necessary to establish an efficient method for detecting these substances. Herein, a molecularly imprinted polymer (bupivacaine) was prepared by bulk polymerization and packed into a hollow fiber for use as an extraction phase to fabricate a membrane-protected microsolid phase-extraction device. The optimal values of the influencing parameters for the microextraction process were as follows: a sample solution pH of 9.0, a loading and washing time of 2 h and an elution time of 32 min. A GC-MS method was established for determination of local anesthetics and coupled with the microextraction method to successfully detect local anesthetics in cosmetic samples. The calibration curve for the proposed method was linear in the range of 0.4∼50 mg/L and showed a good correlation coefficient (r² ). The LODs for local anesthetics were in the range of 0.01∼0.71 mg/L. The molecularly imprinted polymer exhibited good imprinting and selectivity, and the microsolid phase-extraction device was simple and inexpensive and fabrication was reproducible. The combination of molecular imprinting technology, membrane separation and microsolid phase-extraction methods used in this study can potentially be applied to pretreat local anesthetics in cosmetic samples. This article is protected by copyright. All rights reserved.

Trends in Innovations and Recent Advances in Membrane Protected Extraction Techniques for Organics in Complex Samples

Membrane protected extraction is an ongoing innovation for isolation and pre-concentration of analytes from complex samples. The extraction process, clean-up and pre-concentration of analytes occur in a single step. The inclusion of solid sorbents such as molecularly imprinted polymers (MIPs) after membrane extraction ensures that selective double extraction occurs in a single step. The first step involves selective extraction using the membrane and diffused analytes are trapped on the solid sorbent enclosed in the membrane. No further clean-up is required even for very dirty samples like plant extracts and wastewaters samples. Sample clean-up occurs during extraction in the first process and not as additional step since matrix components are prevented from trapping on the sorbent. This can be referred to as prevention is better than cure approach. In this work, the analytical methods that employed membrane protected extraction for various organics such as pesticides, polycyclic aromatic hydrocarbons, and pharmaceuticals are reviewed. The designs of these analytical methods, their applications, advantages and drawbacks are discussed in this review. Literature suggests that the introduction of solid sorbents in membrane creates the much-needed synergy in selectivity. Previous reviews focused on membrane combinations with MIPs while discussing micro-solid-phase extraction. The scope of this review was broadened to include other sample preparation aspects such as membrane protected stir bar solvent extraction and membrane protected solid-phase microextraction. In addition, novel sample preparation methods for solid samples which include Soxhlet membrane protected molecular imprinted solid phase extraction and membrane protected ultra sound assisted extracted are discussed.

Strategies of dispersive liquid-liquid microextraction for coastal zone environmental pollutant determination

Coastal zone means the interface of land and sea, and therefore, environmental pollutants steaming from land-based activities (like manufactories) and sea-based activities (like shipping) are all existing in coastal zone. These pollutants usually have characteristics of low residues, complicated matrices, easy accumulation and so on, causing difficulty to detect coastal pollutants quickly and sensitively. It is imperative to perform effective sample preparation prior to instrumental analysis. Dispersive liquid-liquid microextraction (DLLME) has attracted significant research interest for sample preparation, owing to its high enrichment ability, low reagent/sample consumption, and wide analyte/matrix applicability, as well as robustness, simplicity, rapidity and inexpensiveness. Herein, we comprehensively review the recent advancements of DLLME technology and its analytical parameters including enrichment principles, extraction modes, and practical application; the emphasis is on novel mode-construction and representative coastal-environmental pollutants extraction. Construction strategies are highlighted by classifying DLLME into five major modes, according to extractant's types, including normal ones, low density solvents, ionic liquids, deep eutectic solvents and others. The coupling of DLLME with other extraction techniques like solid-phase extraction is also briefly introduced. The strengths and weaknesses of each strategy and its rationality are also elaborated. In addition, some typical applications of the different DLLME modes for the determination of organic compounds and heavy metals in coastal water, sediment, soil, and biota are summarized. The increasingly concerned green aspects and instrumentation of DLLME are presented, and finally, the challenges and perspectives of the DLLME for environmental analysis are proposed.

Sodium dodecyl sulfate-multi-walled carbon nanotubes-coated-membrane solid phase extraction of glucocorticoids in aqueous matrices

A membrane-based solid phase extraction (SPE)-ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method was developed for the determination of nine glucocorticoids in water. This new hybrid SPE approach involved the deposition of sodium dodecyl sulfate (SDS)-multi-walled carbon nanotubes (MWCNTs) on a piece of polypropylene membrane that served as the extraction device. Hitherto, such a sample preparation procedure has not been applied to the analysis of water contaminants before. The use of the surfactant helped to disperse the MWCNTs effectively so that they were coated uniformly onto the polypropylene membrane. This increased the overall extraction efficiency of the procedure. Characterisation of the SDS-MWCNTs material was performed using transmission electron microscopy and scanning electron microscopy. The membrane device did not require a pre-conditioning step. The most favourable extraction parameters such as type of surfactant, percentage of surfactant, type of desorption solvent, stirring rate, desorption time, extraction time, temperature, salting-out effect, pH and diameter of MWCNTs were obtained. The method showed linearity ranges from 0.2 to 100 ng mL^-1 for hydrocortisone, dexamethasone, cortisone acetate and beclomethasone dipropionate, and 0.5-100 ng mL^-1 for the rest of the analytes. Limits of detection ranging from 0.019 to 0.098 ng mL^-1, and limits of quantification ranging from 0.065 to 0.326 ng mL^-1, were obtained for the analytes. The intra-day repeatability was between 1.77 and 3.56% while the inter-day reproducibility was between 2.69 and 9.53%, respectively. The method was used to analyse glucocorticoids as contaminants in the canal water samples.

Graphene and zeolite as adsorbents in bar-micro-solid phase extraction of pharmaceutical compounds of diverse polarities

A bar micro-solid phase (bar μ-SPE) extraction method using either graphene or zeolite or their mixtures as an adsorbent, coupled with high-performance liquid chromatography (using a C1 column) was developed for the simultaneous determination of pharmaceutical compounds (metformin (MET), buformin (BUF), phenformin (PHEN) and propranolol (PROP)) of diverse polarity (log P from −1.82 to 3.10). Parameters influencing the extraction, such as conditioning solvents, pH of the sample, sample volume, amount of adsorbent, stirring rate, time of extraction, type and volume of desorption solvent and time of desorption were investigated. Under the optimized conditions, the extraction method using graphene (extraction efficiency, % EE, ∼6–15%) resulted in the least amount of extracted drugs. However, the use of zeolite and zeolite/graphene mixtures improves the % EE significantly, i.e. 30% for PHEN and 42% for PROP using zeolite; 22% for MET and 18% for BUF using the adsorbent mixture. Under similar conditions, enrichment factors for these drugs range from 11–15. The validated method was performed for the determination of the drugs that were spiked to urine samples. Good recoveries ranging from 72.8 to 116% were achieved.

A bar micro-solid phase (bar μ-SPE) extraction method using either graphene or zeolite or their mixtures as an adsorbent, coupled with high-performance liquid chromatography was developed for the determination of pharmaceutical compounds of diverse polarity.

Zeolitic imidazolate frameworks in analytical sample preparation

Zeolitic imidazolate frameworks are a class of metal-organic frameworks that are topologically isomorphic with zeolites. Zeolitic imidazolate frameworks are composed of tetrahedrally coordinated metal ions connected by imidazolate linkers and have a high porosity and chemical stability. Here, we summarize the progress made in the application of zeolitic imidazolate frameworks in sample preparation for analytical purposes. This review is focused on analytical methods based on liquid chromatography, gas chromatography, or capillary electrophoresis, where the use of zeolitic imidazolate frameworks has contributed to increasing the sensitivity and selectivity of the method. While bulk zeolitic imidazolate frameworks have been directly used in analytical sample preparation protocols, a variety of strategies for their magnetization or their incorporation into sorbent particles, monoliths, fibers, stir bars, or thin films, have been developed. These modifications have facilitated the handling and application of zeolitic imidazolate frameworks for a number of analytical sample treatments including magnetic solid-phase extraction, solid-phase microextraction, stir bar sorptive extraction, or thin film microextraction, among other techniques.

Enhanced microextraction of endocrine disrupting chemicals adsorbed on airborne fine particulate matter with gas chromatography-tandem mass spectrometric analysis

A novel double-microextraction approach, combining dispersive liquid-liquid microextraction (DLLME) and vortex-assisted micro-solid-phase extraction (VA-µ-SPE) was developed. The procedure was applied to extract endocrine disrupting chemicals (EDCs) consisting of three phthalate esters (PEs) and bisphenol A (BPA) associated with PM_2.5 (airborne particulate matter with aerodynamic diameter ≤ 2.5 µm). Gas chromatography-tandem mass spectrometry (GC-MS/MS) was used for determination of the analytes. These analytes were first ultrasonically desorbed from PM_2.5 in a 10% acetone aqueous solution. DLLME was used to first preconcentrate the analytes; the sample solution, still in the same vial, was then subjected to VA-µ-SPE. The synergistic effects provided by the combination of the microextraction techniques provided advantages such as high enrichment factors and good cleanup performance. Various extraction parameters such as type and volume of extractant solvent (for DLLME), and type of sorbent, extraction time, desorption solvent, volume of desorption solvent and desorption time (for µ-SPE) were evaluated. Multi-walled carbon nanotubes were found to be the most suitable sorbent. This procedure achieved good precision with intra- and inter-day relative standard deviations of between 1.93 and 9.95%. Good linearity ranges (0.3-100 ng/mL and 0.5-100 ng/mL, depending on analytes), and limits of detection (LODs) of between 0.07 and 0.15 ng/mL were obtained. The method was used to determine the levels of PEs and BPA in ambient air, with concentrations ranging between below the limits of quantification and 0.48 ng/m³. DLLME-VA-µ-SPE-GC-MS/MS was demonstrated to be suitable for the determination of these EDCs present in PM_2.5.

Mixed Matrix Membrane Tip Extraction Coupled with UPLC–MS/MS for the Monitoring of Nonsteroidal Anti-Inflammatory Drugs in Water Samples

An ultra-performance liquid chromatography–tandem mass spectrometry (UPLC–MS/MS) method, in combination with a mixed matrix membrane microextraction method for the quantification of nonsteroidal anti-inflammatory drugs (NSAIDs) in environmental water samples, is reported. The extraction device was prepared by casting well-dispersed polymeric bonded octadecyl (C18) particles in a cellulose triacetate matrix solution onto commercially available 200 μL micropipette tips. The membrane formed contains 25% of the adsorbent loading amount and was firmly attached to the inner wall of the membrane tip. The dynamic extraction was performed by withdrawing and dispensing the sample solution through the tip device for effective analyte adsorption, followed by the analyte desorption process into 40 μL of methanol and acetonitrile (1:1) prior to UPLC–MS/MS analysis. NSAIDs—namely diclofenac, ibuprofen, indoprofen, naproxen and sulindac—were chosen as targeted analytes. Several extraction parameters were comprehensively optimized, including sample pH value, ionic strength, dynamic extraction cycle, desorption solvent and desorption time. The optimized conditions demonstrated a linear range from 0.25 to 500 ng L−1, with correlation coefficients (r2) from 0.9988 to 0.9992 and detection limits ranging from 0.08 to 0.40 ng L−1. The recoveries of the spiked water samples were between 92% and 99% and exhibited excellent precision relative to standard deviations (RSDs ≤ 4.9%), and enrichment factors (EFs) were at 201–249 for the developed approach.

A simple strategy based on fibers coated with surfactant-functionalized multiwalled carbon nanotubes to improve the properties of solid-phase microextraction of phenols in aqueous solution

Methods and experiments

In this study, a functionalized multiwalled carbon nanotube (MWCNT)-coated solid-phase microextraction (SPME) fiber was developed for concentrating analytes in aqueous samples. Sodium deoxycholate (NaDC) was used as a dispersing agent for non-covalent modification of MWCNTs. The coating showed porous structure and large adsorption capacity. To investigate the capability of this MWCNTs/NaDC SPME fiber, it was applied to the analysis of phenols in aqueous solution. After extraction, the analytes were desorbed in an acetonitrile–water solution and analyzed using high-performance liquid chromatography.

Results

The MWCNTs/NaDC fiber exhibited good analytical performance, and fine preparation reproducibility was obtained with the relative standard deviations (RSDs) ranging from 4.9% to 10.2% (n = 6) in one batch, from 5.7% to 11.9% (n = 3) among different batches. Under the optimum extraction conditions, the detection limits were 0.15–0.30 ng/mL(S/N = 3), the linear detection ranges were 1–100 ng/mL (R² ≥ 0.9997) for these analytes, and good recoveries (80.3–95.4%) were obtained for the spiked samples.

Conclusion

This is a simple and accurate pretreatment method for the analysis of phenols in aqueous samples.

Colorimetric determination of amaranth followed enrichment and separation using buoyant adsorbents

A buoyant solid-phase extraction adsorbent was prepared by sodium alginate-coated hollow glass microspheres (HGMs) modified with 3-aminopropyltrimethoxysilane (3-APTS) for the separation and enrichment of anionic dye amaranth. After adsorbing amaranth, these low-density adsorbents can float on the surface of the solution, so the separation between adsorbents and substrates can be carried out by flotation. Quantitative determination of amaranth after separation and enrichment can be achieved by combining spectrophotometry. Under the optimum conditions, the linear range and detection limit for amaranth detection were 0.02 mg L−1–2.0 mg L−1 and 0.0021 mg L−1, respectively. The proposed method was applied to the determination of amaranth in different beverages, and the results were in good agreement with those by high-performance liquid chromatography (HPLC). The recoveries of amaranth in different beverages were between 97.93 and 105.91%. The floating adsorbent can be used as a conventional sample preparation method for the detection of low concentration analytes in complex samples.

Electrospun terpolymeric nanofiber membrane for micro solid-phase extraction of diazinon and chlorpyrifos from aqueous samples

The present study deals with the synthesis and electrospining of a new terpolymer nanofiber in order to determine the amount of diazinon and chlorpyrifos in water and fruit juice samples. The synthesized terpolymer and the prepared nanofiber were characterized using ¹ H NMR spectroscopy, FTIR spectroscopy, scanning electron microscopy, and gel permeation chromatography. The performance of terpolymer nanofiber, prepared as a sorbent for micro solid phase extraction was investigated for the extraction of diazinon and chlorpyrifos from aquaeous media. Then, the target analytes were desorbed from the coating with an organic solvent and analyzed by gas chromatography with flame ionization detector. Extraction efficiencies were significant (>90%) under the optimum condition. The proposed method also demonstrated good linear dynamic ranges for diazinon and chlorpyrifos (3-250 and 5-200 µg/L), and low limit of detections (0.5 and 0.7 µg/L) respectively. Moreover, under optimum condition for extraction of diazinon and chlorpyrifos, square of correlation coefficients (R² ) of 0.9978 and 0.9953 and relative standard deviations of 4.6 and 5.1% were achieved, respectively. The recoveries for diazinon and chlorpyrifos were in the range of 85-97%.

In-situ preparation of porous monolithic polymer inside hollow fiber as a micro-solid phase extraction device for glucocorticoids in cosmetics

Glucocorticoids have a certain whitening effect on the skin. However, frequent and long-term use of cosmetics including glucocorticoids is harmful to health. Herein, we proposed a novel micro-solid phase extraction method for the detection of prednisolone acetate, prednisone, and prednisolone in cosmetics coupled with high-performance liquid chromatography. In this method, porous monolithic polymer micro-extraction bars were prepared by "one-step, one-pot" in situ photopolymerization combined with sacrificial support in hollow fiber under water atmosphere. The crucial factors such as pH of sample solution, extraction, and elution times that influence micro-extraction were optimized and found to be 9.0, 2 h, and 32 min, respectively. Under the optimum experimental conditions, the linear range of the calibration curves were from 5.0 to 2000 µg/L with correlation coefficients (R² ) between 0.9922 and 0.9996. The limit of detection and limit of quantification were 1.5 µg/L and 5.0 µg/L, respectively, and the recoveries were found to be in range of 69.0-113.3%. The analysis of precision for intraday and interday were less than 10.40 and 10.59%. The device has been successfully achieved photopolymerization under water atmosphere. The results indicated that this method is simple, accurate, and satisfactory for the pretreatment and determination of glucocorticoids in complex cosmetics samples.

Organic Acids and Polyphenols Determination in Polish Wines by Ultrasound-Assisted Solvent Extraction of Porous Membrane-Packed Liquid Samples

In the near future, Poland is going to have more and more favorable conditions for viticulture. Organic acids and polyphenols are among the most commonly analyzed compounds due to their beneficial properties for human health and their importance in the winemaking process. In this work, a new technique involving ultrasound-assisted solvent extraction of porous membrane-packed liquid samples (UASE-PMLS) was for the first time described and applied for real samples. The methodology based on UASE-PMLS for organic acids and polyphenols in wine samples was optimized and validated. Using the new technique coupled to GC–MS, organic acids and polyphenols were evaluated in Polish wine samples. Extraction solvent, extraction temperature, derivatization time and sample pH were optimized. Chemometric tools were used for data treatment. Good linearity was obtained for the concentration ranges evaluated with r values between 0.9852 and 0.9993. All parameters of method validation (intra- and inter-day precision and matrix effect) were over 80% with coefficient of variation (CV) up to 17%. Recovery was between (92.0 ± 8.5)% and (113 ± 16)%. Finally, green assessment was evaluated using Analytical Eco-Scale and Green Analytical Procedure Index (GAPI). The UASE-PMLS is characterized by many advantages, e.g., the extraction process is fast and easy coupled to GC–MS. Regarding other extraction techniques, the amount of used solvent is minimum, and no waste is generated. Therefore, it is an environmentally friendly technique.

Coupling of micro-solid-phase extraction and internal extractive electrospray ionization mass spectrometry for ultra-sensitive detection of 1-hydroxypyrene and papaverine in human urine samples

Quantification of ultra-trace analytes in complex biological samples using micro-solid-phase extraction followed by direct detection with internal extractive electrospray ionization mass spectrometry (μSPE-iEESI-MS) was demonstrated. 1-Hydroxypyrene (1-OHP) and papaverine at attomole levels in human raw urine samples were analyzed under negative and positive ion detection mode, respectively. The μSPE was simply prepared by packing a disposable syringe filter with octadecyl carbon chain (C18)-bonded micro silica particles, which were then treated as the "bulk sample" after the analytes were efficiently enriched by the C18 particles. Under the optimized experimental conditions, the analytes were readily eluted by isopropanol/water (80/20, V/V) at a high voltage of ± 4.0 kV, producing analyte ions under ambient conditions. The limit of detection (LOD) was 0.02 pg/L (9.2 amol) for 1-hydroxypyrene and 0.02 pg/L (5.9 amol) for papaverine. The acceptable linearity (R² > 0.99), signal stability (RSD ≤ 10.7%), spike recoveries (91-95%), and comparable results for real urine samples were also achieved, opening up possibilities for quantitative analysis of trace compounds (at attomole levels) in complex bio-samples. Graphical abstract.

Miniaturized sample preparation methods for saliva analysis

Saliva, as the first body fluid encountering with the exogenous materials, has good correlation with blood and plays an important role in bioanalysis. However, saliva has not been studied as much as the other biological fluids mainly due to restricted access to its large volumes. In recent years, there is a growing interest for saliva analysis owing to the emergence of miniaturized sample preparation methods. The purpose of this paper is to review all microextraction methods and their principles of operation. In the following, we examine the methods used to analyze saliva up to now and discuss the potential of the other microextraction methods for saliva analysis to encourage research groups for more focus on this important subject area.