Self-Assembly of Carbon Nanotubes via Ethanol Chemical Vapor Deposition for the Synthesis of Gas Chromatography Columns

Fouling Reduction and Thermal Efficiency Enhancement in Membrane Distillation Using a Bilayer-Fluorinated Alkyl Silane-Carbon Nanotube Membrane

In this study, we report the robust hydrophobicity, lower fouling propensity, and high thermal efficiency of the 1H,1H,2H,2H-perfluorooctyltriethoxysilane (FAS)-coated, carbon nanotube-immobilized membrane (CNIM) when applied to desalination via membrane distillation. Referred to as FAS-CNIM, the membrane was developed through a process that combined the drop-casting of nanotubes flowed by a dip coating of the FAS layer. The membranes were tested for porosity, surface morphology, thermal stability, contact angle, and flux. The static contact angle of the FAS-CNIM was 153 ± 1°, and the modified membrane showed enhancement in water flux by 18% compared to the base PTFE membrane. The flux was tested at different operating conditions and the fouling behavior was investigated under extreme conditions using a CaCO3 as well as a mixture of CaCO3 and CaSO4 solution. The FAS-CNIM showed significantly lower fouling than plain PTFE or the CNIM; the relative flux reduction was 34.4% and 37.6% lower than the control for the CaCO3 and CaCO3/CaSO4 mixed salt solution. The FAS-CNIM exhibited a notable decrease in specific energy consumption (SEC). Specifically, the SEC for the FAS-CNIM measured 311 kwh/m3 compared to 330.5 kwh/m3 for the CNIM and 354 kwh/m3 for PTFE using a mixture of CaCO3/CaSO4. This investigation underscores the significant contribution of the carbon nanotubes' (CNTs) intermediate layer in creating a durable superhydrophobic membrane, highlighting the potential of utilizing carbon nanotubes for tailored interface engineering to tackle fouling for salt mixtures. The innovative design of a superhydrophobic membrane has the potential to alleviate wetting issues resulting from low surface energy contaminants present in the feed of membrane distillation processes.

Carbon Nanotube Enhanced Filtration and Dewatering of Kerosene

Current approaches to dewatering aviation fuel such as kerosene are adsorption by activated charcoal, gravity separation, etc. The objective of this work is to develop and demonstrate the filtration and dewatering of kerosene using a carbon nanotube immobilised membrane (CNIM). Highly hydrophobic membranes were prepared by immobilising carbon nanotube (CNTs) over polytetrafluoroethylene (PTFE) and polyvinylidene difluoride (PVDF) microfiltration membrane for the dewatering of ppm level water from kerosene. The effects of different CNT concentrations on membrane morphology, hydrophobicity, porosity, and permeability were characterised. After immobilising CNT into membranes, the contact angle increased by 9%, 16%, and 43% compared to unmodified 0.1 μm PTFE, 0.22 μm PTFE and 0.22 μm PVDF membranes, respectively. The CNIM showed remarkable separation efficiency for the fuel-water system. The micro/nano water droplets coalesced on the CNT surface to form larger diameters of water droplets detached from the membrane surface, leading to enhanced water rejection. In general, the water rejection increased with the amount of CNT immobilised while the effective surface porosity over pore length and flux decreased. PTFE base membrane showed better performance compared to the PVDF substrate. The CNIMs were fabricated with 0.1 and 0.22 μm PTFE at an optimised CNT loading of 3 and 6 wt.%, and the water rejection was 99.97% and 97.27%, respectively, while the kerosene fluxes were 43.22 kg/m2·h and 55.44 kg/m2·h respectively.

Photothermal Desorption of Toluene from Carbonaceous Substrates Using Light Flash

Millions of workers are occupationally exposed to volatile organic compounds (VOCs) annually. Current exposure assessment techniques primarily utilize sorbent based preconcentrators to collect VOCs, with analysis performed using chemical or thermal desorption. Chemical desorption typically analyzes 1 µL out of a 1 mL (0.1%) extraction volume providing limited sensitivity. Thermal desorption typically analyzes 100% of the sample which provides maximal sensitivity, but does not allow repeat analysis of the sample and often has greater sensitivity than is needed. In this study we describe a novel photothermal desorption (PTD) technique to bridge the sensitivity gap between chemical desorption and thermal desorption. We used PTD to partially desorb toluene from three carbonaceous substrates; activated carbon powder (AC-p), single-walled carbon nanotube (SWNT) powder (SWNT-p) and SWNT felts (SWNT-f). Sorbents were loaded with 435 ug toluene vapour and irradiated at four light energies. Desorption ranged from <0.007% to 0.86% with a single flash depending on substrate and flash energy. PTD was significantly greater and more consistent in SWNT-f substrates compared to AC-p or SWNT-p at all irradiation energies. We attribute the better performance of SWNT-f to greater utilization of its unique nanomaterials properties: high thermal conductivity along the nanotube axis, and greater interconnection within the felt matrix compared to the powdered form.

Carbon nanotube columns for flow systems: influence of synthesis parameters

Flow reactors are expected to play an increasingly important role in the production of chemicals. A simple carbon-based scaffold to easily develop flow systems is here detailed. Using a chemical vapour deposition technique, the controlled in situ growth of vertically aligned (VA) multi-wall carbon nanotubes (MWCNTs) into quartz columns with 2 mm inner diameter is achieved. Several of the described MWCNT columns (CNCs) can be produced at a time. The influence of synthesis parameters on the formation of these VA-MWCNT scaffolds is reported and discussed (e.g. injection time of the precursor, carrier gas flow rate, inner diameter and length of the quartz column, position in the furnace during synthesis). Raman spectroscopy, optical microscopy, scanning and transmission electron microscopy are used to assess the coverage of the inner channel of the quartz column with VA-MWCNTs and their overall quality. The length of the CNCs together with the carrier gas flow rate are found to be key parameters to control the MWCNT length profile within the CNCs. Fluoresceinamine molecules and platinum nanoparticles are successfully immobilised within these MWCNT scaffolds. The benefits of the CNCs for flow system design are summarised as the controlled filling with MWCNTs makes the detailed CNCs versatile scaffolds for flow catalysis and filtration.

Tolfenamic acid on-line preconcentration strategy on carbon nanotubes minicolumn with fluorimetric detection

Nonsteroidal anti-inflammatory agents (NSAIDs) are a group of pharmaceuticals considered one of the most popular drugs used in clinical practice applied to the treatment of acute and chronic conditions. Some pharmaceuticals products are excreted reaching the environment and altering the balance of ecosystems. This work proposes a new fluorimetric flow injection (FI) methodology for the NSAID tolfenamic acid quantification based on the quenching effect of the analyte on fluorescent signal of bovine serum albumin fluorophore. Results put in evidence a mechanism of static quenching, with a Stern Volmer constant value of 1.8 × 10⁷ L mol^-1. To achieve the selective on-line preconcentration of analyte, a carbon nanotubes mini column was introduced in the FI configuration producing a beneficial effect on high sampling frequency, minimum sample and reagents consumption. The experimental factors that influence batch fluorescent signal and FI analysis have been studied and optimized. At optimal experimental conditions, an adequate tolerance to foreign species was shown. With the flow configuration, a LOD of 0.019 μg L^-1, a LOQ of 0.058 μg L^-1 were obtained with a sampling rate of 30 samples h^-1. The new methodology was successfully applied to analyte determination in tap water and pharmaceutical and factory waste samples with recuperation near to 100%.

Nanostructured Silver Coating as a Stationary Phase for Capillary Gas Chromatography

A capillary column coated with nanostructured silver coating was fabricated for gas chromatography. The nanostructured silver coating, about 80-120 nm in thickness, was prepared as the stationary phase via silver mirror reaction, and was characterized by SEM and EDS. The column was evaluated using different types of model analytes, including n-alkanes, n-alcohols, benzenes, and Grob mixture. A baseline separation of ten n-alkanes on the silver column (15 m × 0.20 mm i.d.) was achieved within 3.5 min through the main hydrophobic mechanism. A mixture of six n-alcohols, or another mixture containing three butanol isomers and two octanol isomers, was separated well on the column. The column separated some benzenes containing benzene, toluene, ethylbenzene, p-xylene, o-xylene, styrene, benzaldehyde, and benzyl alcohol. A Grob mixture containing seven analytes was also separated successfully. Based on a multiple retention mechanism such as hydrophobic, dipole-dipole, and dipole-induced dipole interactions, the silver column achieved a good separation of twelve different types of compounds within 2.5 min. The column presented satisfactory separation repeatability with relative standard deviation of retention time between 0.073% and 0.591%. The results indicate that the silver column is promising for gas chromatographic separation.

Cellulose type chiral stationary phase based on reduced graphene oxide@silica gel for the enantiomer separation of chiral compounds

The graphene oxide (GO) was covalently coupled to the surfaces of silica gel (SiO2 ) microspheres by amide bond to get the graphene oxide@silica gel (GO@SiO2 ). Then, the GO@SiO2 was reduced with hydrazine to the reduced graphene oxide@silica gel (rGO@SiO2 ), and the cellulose derivatives were physically coated on the surfaces of rGO@SiO2 to prepare a chiral stationary phase (CSP) for high performance liquid chromatography. Under the optimum experimental conditions, eight benzene-enriched enantiomers were separated completely, and the resolution of trans-stilbene oxide perfectly reached 4.83. Compared with the blank column of non-bonded rGO, the separation performance is better on the new CSP, which is due to the existence of rGO to produce special retention interaction with analytes, such as π-π stacking, hydrophobic effect, π-π electron-donor-acceptor interaction, and hydrogen bonding. Therefore, the obtained CSP shows special selectivity for benzene-enriched enantiomers, improves separation selectivity and efficiency, and rGO plays a synergistic effect with cellulose derivatives on enantioseparation.

A physical entrapment method for the preparation of carbon nanotube reinforced macroporous adsorption resin with enhanced selective extraction performance

In this paper, we demonstrate a novel carbon nanotube (CNT) reinforced macroporous adsorption resin (MAR) for the first time. The CNTs were dispersed in water via sonication, and then in situ physically entrapped in the pores of MAR by capillary forces and sonication. The resulting CNT reinforced MAR (CNT-MAR) was proved by transmission electron microscopy (TEM) and confocal laser scanning microscopy (CLSM), and subsequently applied to extract a mixture of 8 types, 14 natural products. For comparison, the extraction efficiency of original MAR without CNTs was also evaluated. After extraction, the supernatants were detected via high-performance liquid chromatography (HPLC). The results indicated that the introduction of carbon nanotubes (CNTs) into the pores of MAR can significantly improve the adsorptive selectivity of MAR for natural products. The original MAR without CNTs has almost the same adsorption capacity for selectively extracting 3 types of natural products (phenols, alkaloids and anthraquinones). However, the CNT-MAR only could selectively extract anthraquinones and the adsorption capacity for three anthraquinone natural products is 1.46-1.83 times higher than that of unmodified MAR. In order to achieve the highest extraction efficiency of CNT-MAR for anthraquinone natural products, the main extraction parameters such as the extraction time and the pH value were also optimized. The CNT-MAR demonstrated an excellent ability to extract anthraquinone natural products with high selectivity and adsorption capacity. Due to its low cost, easy preparation and use, and operational characteristics, it shows great potential for selective extraction of natural products.

Basic Overview on Gas Chromatography Columns

The main purpose of this chapter is to give a basic overview on the basic components of stationary phases/columns in gas chromatography ( GC ) for the benefit of students and beginners in the field of GC .

Application of Carbonaceous Materials in Separation Science

Porous carbons in the separation sciences occupy an important niche owing to their unique retention characteristics, chemical stability and the ability to control pore structure through template strategies. However, these same synthetic processes utilise oil-based carbonising resins and high temperature, energy-intensive pyrolysis steps to ensure the carbon product has pore-size regularity, minimal micropore content and homogeneous surface chemistry. This chapter will primarily focus on the development of porous carbons for application as chromatographic stationary phases. Discussion will cover the unique characteristics of the porous carbon retention mechanism and its application in separating a broad range of analyte classes. The chapter then moves on to describe the current disadvantages in the manufacture of commercially available carbon phase and then highlight recent efforts aimed at the development of alternative porous carbon stationary phases derived from sustainable carbon precursors.

Photothermal desorption of single-walled carbon nanotubes and coconut shell-activated carbons using a continuous light source for application in air sampling

Many techniques exist to measure airborne volatile organic compounds (VOCs), each with differing advantages; sorbent sampling is compact, versatile, has good sample stability, and is the preferred technique for collecting VOCs for hygienists. Development of a desorption technique that allows multiple analyses per sample (similar to chemical desorption) with enhanced sensitivity (similar to thermal desorption) would be helpful to field hygienists. In this study, activated carbon (AC) and single-walled carbon nanotubes (SWNT) were preloaded with toluene vapor and partially desorbed with light using a common 12-V DC, 50-W incandescent/halogen lamp. A series of experimental chamber configurations were explored starting with a 500-ml chamber under static conditions, then with low ventilation and high ventilation, finally a 75-ml high ventilation chamber was evaluated. When preloaded with toluene and irradiated at the highest lamp setting for 4min, AC desorbed 13.9, 18.5, 23.8, and 45.9% of the loaded VOC mass, in each chamber configuration, respectively; SWNT desorbed 25.2, 24.3, 37.4, and 70.5% of the loaded VOC mass, respectively. SWNT desorption was significantly greater than AC in all test conditions (P = 0.02-<0.0001) demonstrating a substantial difference in sorbent performance. When loaded with 0.435mg toluene and desorbed at the highest lamp setting for 4min in the final chamber design, the mean desorption for AC was 45.8% (39.7, 52.0) and SWNT was 72.6% (68.8, 76.4) (mean represented in terms of 95% confidence interval). All desorption measurements were obtained using a field grade photoionization detector; this demonstrates the potential of using this technique to perform infield prescreening of VOC samples for immediate exposure feedback and in the analytical lab to introduce sample to a gas chromatograph for detailed analysis of the sample.

Carbon nanoparticles from corn stalk soot and its novel application as stationary phase of hydrophilic interaction chromatography and per aqueous liquid chromatography

Carbon nanoparticles (CNPs) (6-18 nm in size) were prepared by refluxing corn stalk soot in nitric acid. The obtained acid-oxidized CNPs are soluble in water due to the existence of carboxylic and hydroxyl groups. (13)C NMR measurement shows the CNPs are mainly of sp(2) and sp(3) carbon structure different from CNPs obtained from candle soot and natural gas soot. Furthermore, these CNPs exhibit unique photoluminescence properties. Interestingly, the CNPs might be exploited to immobilize on the surface of porous silica particles as chromatographic stationary phase. The resultant packing material was evaluated by high-performance liquid chromatography, indicating that the new stationary phase could be used in hydrophilic interaction liquid chromatography (HILIC) and per aqueous liquid chromatography (PALC) modes. The separation of five nucleosides, four sulfa compounds and safflower injection was achieved by using the new column in the HILIC and PALC modes, respectively.