4D Shearforce-Based Constant-Distance Mode Scanning Electrochemical Microscopy

Operando Scanning Electrochemical Probe Microscopy during Electrocatalysis

Scanning electrochemical probe microscopy (SEPM) techniques can disclose the local electrochemical reactivity of interfaces in single-entity and sub-entity studies. Operando SEPM measurements consist of using a SEPM tip to investigate the performance of electrocatalysts, while the reactivity of the interface is simultaneously modulated. This powerful combination can correlate electrochemical activity with changes in surface properties, e.g., topography and structure, as well as provide insight into reaction mechanisms. The focus of this review is to reveal the recent progress in local SEPM measurements of the catalytic activity of a surface toward the reduction and evolution of O₂ and H₂ and electrochemical conversion of CO₂. The capabilities of SEPMs are showcased, and the possibility of coupling other techniques to SEPMs is presented. Emphasis is given to scanning electrochemical microscopy (SECM), scanning ion conductance microscopy (SICM), electrochemical scanning tunneling microscopy (EC-STM), and scanning electrochemical cell microscopy (SECCM).

A probe-based nanometric morphology measurement system using intermittent-contact mode

In the present study, a homemade probe-based nanometric morphology measurement system is proposed, which can be easily integrated with other probes, such as a diamond probe and an electrochemical electrode. In this system, an intermittent-contact mode is adopted, which is based on a set of micro-force servo modules. The micro-force serve module is mainly composed of a piezoelectric ceramic transducer, a capacitive displacement sensor, an excitation piezoelectric ceramic ring, and a four-beam spring. The four-beam spring integrated with a diamond probe is driven by the excitation piezoelectric ceramic ring. The mechanical structure and the control system of the measurement system are also designed. The vibration amplitude and the resolution of a normal load are calibrated during the engagement process under open-loop control. Moreover, the optimal values for parameters P, I, and D are obtained for the closed-loop measurement. The performance of the developed system is verified by measuring a standard sample. The measured depths agree well with the results obtained by commercial atomic force microscopy. The developed system can be used to measure nanostructures with high precision.

Probing the local activity of CO2 reduction on gold gas diffusion electrodes: effect of the catalyst loading and CO2 pressure

Large scale CO2 electrolysis can be achieved using gas diffusion electrodes (GDEs), and is an essential step towards broader implementation of carbon capture and utilization strategies. Different variables are known to affect the performance of GDEs. Especially regarding the catalyst loading, there are diverging trends reported in terms of activity and selectivity, e.g. for CO2 reduction to CO. We have used shear-force based Au nanoelectrode positioning and scanning electrochemical microscopy (SECM) in the surface-generation tip collection mode to evaluate the activity of Au GDEs for CO2 reduction as a function of catalyst loading and CO2 back pressure. Using a Au nanoelectrode, we have locally measured the amount of CO produced along a catalyst loading gradient under operando conditions. We observed that an optimum local loading of catalyst is necessary to achieve high activities. However, this optimum is directly dependent on the CO2 back pressure. Our work does not only present a tool to evaluate the activity of GDEs locally, it also allows drawing a more precise picture regarding the effect of catalyst loading and CO2 back pressure on their performance.

Super-resolution Scanning Electrochemical Microscopy

To achieve super-resolution scanning electrochemical microscopy (SECM), we must overcome the theoretical limitation associated with noncontact electrochemical imaging of surface-generated species. This is the requirement for mass transfer to the electrode, which gives rise to the diffusional broadening of surface features. In this work, a procedure is developed for overcoming this limitation and thus generating "super-resolved" images using point spread function (PSF)-based deconvolution, where the point conductor plays the same role as the point emitter in optical imaging. In contrast to previous efforts in SECM towards this goal, our method uses a finite element model to generate a pair of corresponding blurred and sharp images for PSF estimation, avoiding the need to perform parameter optimization for effective deconvolution. It can therefore be used for retroactive data treatment and an enhanced understanding of the structure-property relationships that SECM provides.

Scanning electrochemical microscopy in the development of enzymatic sensors and immunosensors

Scanning electrochemical microscopy (SECM) is very useful, non-invasive tool for the analysis of surfaces pre-modified with biomolecules or by whole cells. This review focuses on the application of SECM technique for the analysis of surfaces pre-modified with enzymes (horseradish peroxidase, alkaline phosphatase and glucose oxidase) or labelled with antibody-enzyme conjugates. The working principles and operating modes of SECM are outlined. The applicability of feedback, generation-collection and redox competition modes of SECM on surfaces modified by enzymes or labelled with antibody-enzyme conjugates is discussed. SECM is important in the development of miniaturized bioanalytical systems with enzymes, since it can provide information about the local enzyme activity. Technical challenges and advantages of SECM, experimental parameters, used enzymes and redox mediators, immunoassay formats and analytical parameters of enzymatic SECM sensors and immunosensors are reviewed.

Analysing single live cells by scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) offers single live cell activities along its topography toward cellular physiology and pathology.

Biological imaging with scanning electrochemical microscopy

Scanning electrochemical microscopy (SECM) is a powerful and versatile technique for visualizing the local electrochemical activity of a surface as an ultramicroelectrode tip is moved towards or over a sample of interest using precise positioning systems. In comparison with other scanning probe techniques, SECM not only enables topographical surface mapping but also gathers chemical information with high spatial resolution. Considerable progress has been made in the analysis of biological samples, including living cells and immobilized biomacromolecules such as enzymes, antibodies and DNA fragments. Moreover, combinations of SECM with comple-mentary analytical tools broadened its applicability and facilitated multi-functional analysis with extended life science capabilities. The aim of this review is to present a brief topical overview on recent applications of biological SECM, with particular emphasis on important technical improvements of this surface imaging technique, recommended applications and future trends.

Recent Advances in Scanning Electrochemical Microscopy for Biological Applications

Scanning electrochemical microscopy (SECM) is a chemical microscopy technique with high spatial resolution for imaging sample topography and mapping specific chemical species in liquid environments. With the development of smaller, more sensitive ultramicroelectrodes (UMEs) and more precise computer-controlled measurements, SECM has been widely used to study biological systems over the past three decades. Recent methodological breakthroughs have popularized SECM as a tool for investigating molecular-level chemical reactions. The most common applications include monitoring and analyzing the biological processes associated with enzymatic activity and DNA, and the physiological activity of living cells and other microorganisms. The present article first introduces the basic principles of SECM, followed by an updated review of the applications of SECM in biological studies on enzymes, DNA, proteins, and living cells. Particularly, the potential of SECM for investigating bacterial and biofilm activities is discussed.

3D electrochemical and ion current imaging using scanning electrochemical-scanning ion conductance microscopy

Local cell-membrane permeability and ionic strength are important factors for maintaining the functions of cells. Here, we measured the spatial electrochemical and ion concentration profile near the sample surface with nanoscale resolution using scanning electrochemical microscopy (SECM) combined with scanning ion-conductance microscopy (SICM). The ion current feedback system is an effective way to control probe-sample distance without contact and monitor the kinetic effect of mediator regeneration and the chemical concentration profile. For demonstrating 3D electrochemical and ion concentration mapping, we evaluated the reaction rate of electrochemical mediator regeneration on an unbiased conductor and visualized inhomogeneous permeability and the ion concentration 3D profile on a single fixed adipocyte cell surface.

3D Printed and Microcontrolled: The One Hundred Dollars Scanning Electrochemical Microscope

The design and fabrication of a versatile and low-cost electrochemical-scanning probe microscope (EC-SPM) is presented. The proposed equipment relies on the use of modern prototyping tools such as 3D printers and microcontroller boards and only a few "off-the-shelf" parts to deliver a simple yet powerful EC-SPM equipment capable of performing simple space-resolved electrochemical measurements. The equipment was able to perform space-resolved electrochemical measurements using a platinum ultramicroelectrode (UME) as the working electrode on a scanning electrochemical microscopy (SECM) configuration and was used to record approach curves, line scans, and array scans over an insulating substrate. The performance of the proposed equipment was found to be adequate for simple SECM measurements under hindered diffusion conditions. Because of its flexible design (software and hardware), more complex array scan patterns, only found on high-end EC-SPM setups such as hopping mode scan, were easily implemented on the built equipment. Despite its simplicity, the versatility and low cost of the proposed design make it an attractive alternative as a teaching platform as well as a platform for developing more elaborate EC-SPM setups.

Hopping intermittent contact-scanning electrochemical microscopy (HIC-SECM) as a new local dissolution kinetic probe: application to salicylic acid dissolution in aqueous solution

Dissolution kinetics of the (110) face of salicylic acid in aqueous solution is determined by hopping intermittent contact-scanning electrochemical microscopy (HIC-SECM) using a 2.5 μm diameter platinum ultramicroelectrode (UME). The method operates by translating the probe UME towards the surface at a series of positions across the crystal and inducing dissolution via the reduction of protons to hydrogen, which titrates the weak acid and promotes the dissolution reaction, but only when the UME is close to the crystal. Most importantly, as dissolution is only briefly and transiently induced at each location, the initial dissolution kinetics of an as-grown single crystal surface can be measured, rather than a surface which has undergone significant dissolution (pitting), as in other techniques. Mass transport and kinetics in the system are modelled using finite element method simulations which allows dissolution rate constants to be evaluated. It is found that the kinetics of an 'as-grown' crystal are much slower than for a surface that has undergone partial bulk dissolution (mimicking conventional techniques), which can be attributed to a dramatic change in surface morphology as identified by atomic force microscopy (AFM). The 'as-grown' (110) surface presents extended terrace structures to the solution which evidently dissolve slowly, whereas a partially dissolved surface has extensive etch features and step sites which greatly enhance dissolution kinetics. This means that crystals such as salicylic acid will show time-dependent dissolution kinetics (fluxes) that are strongly dependent on crystal history, and this needs to be taken into account to fully understand dissolution.

A time course study of cadmium effect on membrane permeability of single human bladder cancer cells using scanning electrochemical microscopy

Cd(2+) is carcinogenic to both humans and experimental animals. We present quantitative time-course imaging of Cd(2+)-induced variation in the membrane permeability of single live human bladder cancer cells (T24) to ferrocenemethanol using scanning electrochemical microscopy (SECM). High temporal resolution combined with non-invasive nature renders a time-lapse SECM depth scan, a promising method to quantitatively investigate the effectiveness, kinetics, and mechanism of metal ions based on the responses of single live cells in real time. Under unstimulated conditions, T24 cells have constant membrane permeability to ferrocenemethanol of approximately 5.0×10(-5) m/s. When cadmium is added in-situ to T24 cells, the membrane permeability increases up to 3.5×10(-4) m/s, allowing more flux of ferrocenemethanol to the ultramicroelectrode tip. This suggests an increased spreading between the phospholipid heads in the cytoplasmic membrane. Membrane permeability might be used as a measure to probe cell status in practical intoxication cases. The methodology reported here can be applied to many other metals and their interactions with extracellular biomolecules, leading insights into cell physiology and pathobiology.

Constant-distance mode SECM as a tool to visualize local electrocatalytic activity of oxygen reduction catalysts

Multidimensional shearforce-based constant-distance mode scanning electrochemical microscopy (4D SF/CD-SECM) was utilized for the investigation of the activity distribution of oxygen reduction catalysts. Carbon-supported Pt model catalyst powders have been immobilized in recessed microelectrodes and compared to a spot preparation technique. Microcavities serve as platform for the binder-free catalyst sample preparation exhibiting beneficial properties for constant-distance mode SECM imaging concerning modified surface area and catalyst loading. The integration of the redox competition mode of SECM into the detection scheme of the 4D SF/CD mode is demonstrated for specifically adapting high-resolution SECM experiments to powder-based catalyst preparations.

Hopping intermittent contact-scanning electrochemical microscopy (HIC-SECM): visualizing interfacial reactions and fluxes from surfaces to bulk solution

Hopping intermittent contact-scanning electrochemical microscopy (HIC-SECM) is introduced as a powerful new technique for the quantitative visualization of redox activity and concentration at and above a surface of interest. HIC-SECM combines a hopping imaging mode, in which data are acquired at a tip as a function of distance (z) from the surface, at a series of x, y pixels across the surface, using the principles of intermittent contact to provide a nonelectrochemical means of determining when the tip and the substrate come into contact. The implementation of HIC-SECM is described, and SECM feedback measurements in three-dimensional (3D) space over a gold band array are presented. To demonstrate the generality of the methodology, flux imaging is also carried out over a Pt-disk ultramicroelectrode (UME) in the feedback mode and substrate generation/tip collection mode. The type of information that can be extracted from the data sets acquired include x-y current maps at a well-defined tip-substrate separation (parallel to the surface), x-z current maps (normal to the surface), 3D x-y-z profiles, approach curves at particular spots on the surface of interest, and surface topography. Moreover, because HIC-SECM utilizes an oscillating probe, alternating current data are also obtained that greatly enhances the information content compared to other types of electrochemical imaging. Furthermore, interfacial fluxes are ubiquitous in chemistry and allied areas, and HIC-SECM opens up the possibility of detailed flux visualization in three dimensions for many physicochemical processes.

Alternating current scanning electrochemical microscopy with simultaneous fast-scan cyclic voltammetry

Fast-scan cyclic voltammetry (FSCV) is combined with alternating current scanning electrochemical microscopy (AC-SECM) for simultaneous measurements of impedance and faradaic current. Scan rates of 10-1000 V s(-1) were used for voltammetry, while a high-frequency (100 kHz), low-amplitude (10 mV rms) sine wave was added to the voltammetric waveform for the ac measurement. Both a lock-in amplifier and an analog circuit were used to measure the amplitude of the resultant ac signal. The effect of the added sine wave on the voltammetry at a carbon fiber electrode was investigated and found to have negligible effect. The combined FSCV and ac measurements were used to provide simultaneous chemical and topographical information about a substrate using a single carbon fiber probe. The technique is demonstrated in living cell culture, where cellular respiration and topography were simultaneously imaged without the addition of a redox mediator. This approach promises to be useful for the topographical and multidimensional chemical imaging of substrates.

Topographical and electrochemical nanoscale imaging of living cells using voltage-switching mode scanning electrochemical microscopy

We describe voltage-switching mode scanning electrochemical microscopy (VSM-SECM), in which a single SECM tip electrode was used to acquire high-quality topographical and electrochemical images of living cells simultaneously. This was achieved by switching the applied voltage so as to change the faradaic current from a hindered diffusion feedback signal (for distance control and topographical imaging) to the electrochemical flux measurement of interest. This imaging method is robust, and a single nanoscale SECM electrode, which is simple to produce, is used for both topography and activity measurements. In order to minimize the delay at voltage switching, we used pyrolytic carbon nanoelectrodes with 6.5-100 nm radii that rapidly reached a steady-state current, typically in less than 20 ms for the largest electrodes and faster for smaller electrodes. In addition, these carbon nanoelectrodes are suitable for convoluted cell topography imaging because the RG value (ratio of overall probe diameter to active electrode diameter) is typically in the range of 1.5-3.0. We first evaluated the resolution of constant-current mode topography imaging using carbon nanoelectrodes. Next, we performed VSM-SECM measurements to visualize membrane proteins on A431 cells and to detect neurotransmitters from a PC12 cells. We also combined VSM-SECM with surface confocal microscopy to allow simultaneous fluorescence and topographical imaging. VSM-SECM opens up new opportunities in nanoscale chemical mapping at interfaces, and should find wide application in the physical and biological sciences.