Multiplex Lateral Flow Immunoassay for Mycotoxin Determination

Photonic Microbead Array Digital Time-Resolved Fluorescence Ultrasensitive Platform for Simultaneous Detection of Multiple Mycotoxins

Limitations in the sensitivity, linear detection range, and cross-reaction of lateral flow immunoassays mainly hamper their application in rapid screening for multiple targets. In this work, we designed a new time-resolved fluorescence immunoassay (TRFIA) platform to overcome these limitations. This platform uses europium chelate polystyrene (PS@Eu) nanoparticles conjugated with monoclonal antibodies to sense multiple mycotoxins. We employed a competitive TRFIA protocol in which the conjugated PS@Eu was used on the surfaces of photonic microbead arrays (PMAs). The TRFIA signal of PMAs on the pad was recorded with the digital time-resolved fluorescence reader. The developed TRFIA shows wide detection linear ranges (0.01-1000 ng/mL for DON, 0.1-100 ng/mL for OTA, and 0.01-100 ng/mL for AFB1), low limits of detection (LODs) (7.9 pg/mL for DON, 18 pg/mL for OTA, and 7.7 pg/mL for AFB1), good specificity, good recovery ratios (76.68-117.26%), and good reproducibility in grain samples. The simulated fluorescence enhancement effect of PMA indicated that the electric field distribution on the surface of PS@Eu on PMA is twice higher than that on the surface of PS@Eu. The new TRFIA for three kinds of mycotoxins was 1000-fold more sensitive than the classical TRFIA, and it has great potential application in rapid screening for multiple targets.

Detection of foodborne pathogens in contaminated food using nanomaterial-based electrochemical biosensors

Foodborne pathogens are a grave concern for the for food, medical, environmental, and economic sectors. Their ease of transmission and resistance to treatments, such as antimicrobial agents, make them an important challenge. Food tainted with these pathogens is swiftly rejected, and if ingested, can result in severe illnesses and even fatalities. This review provides and overview of the current status of various pathogens and their metabolites transmitted through food. Despite a plethora of studies on treatments to eradicate and inhibit these pathogens, their indiscriminate use can compromise the sensory properties of food and lead to contamination. Therefore, the study of detection methods such as electrochemical biosensors has been proposed, which are devices with advantages such as simplicity, fast response, and sensitivity. However, these biosensors may also present some limitations. In this regard, it has been reported that nanomaterials with high conductivity, surface-to-volume ratio, and robustness have been observed to improve the detection of foodborne pathogens or their metabolites. Therefore, in this work, we analyze the detection of pathogens transmitted through food and their metabolites using electrochemical biosensors based on nanomaterials.

Development of a Sensitive Monoclonal Antibody-Based Colloidal Gold Immunochromatographic Strip for Lomefloxacin Detection in Meat Products

Lomefloxacin (LOM), an antibiotic crucial for preventing various animal diseases in animal husbandry, can pose serious health risks when found in excessive amounts in meat products. The development of highly specific and sensitive colloidal gold immunochromatographic test strips is essential for the accurate detection of this class of antibiotics. Our study utilized a monoclonal antibody (mAb) assay and immunochromatographic strips to detect lomefloxacin residues in meat products. The results showed minimal cross-reactivity with other structural analogs, with a maximum half inhibitory concentration (IC50) of 0.93 ng/mL and a linear range of 0.38 to 2.3 ng/mL for the indirect competitive enzyme-linked immunosorbent assay (ic-ELISA). The recovery of LOM was 80% to 120%, with an average coefficient of variation below 5%. The immunochromatographic strip test results showed a visual detection limit of 2.5 ng/g, meeting the market requirements for the test. This study highlights the significance of specific and sensitive testing methods for detecting lomefloxacin, ensuring consumers' safety and health.

Upconverting Nanoparticle-based Enhanced Luminescence Lateral-Flow Assay for Urinary Biomarker Monitoring

Development of efficient portable sensors for accurately detecting biomarkers is crucial for early disease diagnosis, yet remains a significant challenge. To address this need, we introduce the enhanced luminescence lateral-flow assay, which leverages highly luminescent upconverting nanoparticles (UCNPs) alongside a portable reader and a smartphone app. The sensor's efficiency and versatility were shown for kidney health monitoring as a proof of concept. We engineered Er3+- and Tm3+-doped UCNPs coated with multiple layers, including an undoped inert matrix shell, a mesoporous silica shell, and an outer layer of gold (UCNP@mSiO2@Au). These coatings synergistically enhance emission by over 40-fold and facilitate biomolecule conjugation, rendering UCNP@mSiO2@Au easy to use and suitable for a broad range of bioapplications. Employing these optimized nanoparticles in lateral-flow assays, we successfully detected two acute kidney injury-related biomarkers─kidney injury molecule-1 (KIM-1) and neutrophil gelatinase-associated lipocalin (NGAL)─in urine samples. Using our sensor platform, KIM-1 and NGAL can be accurately detected and quantified within the range of 0.1 to 20 ng/mL, boasting impressively low limits of detection at 0.28 and 0.23 ng/mL, respectively. Validating our approach, we analyzed clinical urine samples, achieving biomarker concentrations that closely correlated with results obtained via ELISA. Importantly, our system enables biomarker quantification in less than 15 min, underscoring the performance of our novel UCNP-based approach and its potential as reliable, rapid, and user-friendly diagnostics.

Exploring Simple Particle-Based Signal Amplification Strategies in a Heterogeneous Sandwich Immunoassay with Optical Detection

Heterogeneous sandwich immunoassays are widely used for biomarker detection in bioanalysis and medical diagnostics. The high analyte sensitivity of the current "gold standard" enzyme-linked immunosorbent assay (ELISA) originates from the signal-generating enzymatic amplification step, yielding a high number of optically detectable reporter molecules. For future point-of-care testing (POCT) and point-of-need applications, there is an increasing interest in more simple detection strategies that circumvent time-consuming and temperature-dependent enzymatic reactions. A common concept to aim for detection limits comparable to those of enzymatic amplification reactions is the usage of polymer nanoparticles (NP) stained with a large number of chromophores. We explored different simple NP-based signal amplification strategies for heterogeneous sandwich immunoassays that rely on an extraction-triggered release step of different types of optically detectable reporters. Therefore, streptavidin-functionalized polystyrene particles (PSP) are utilized as carriers for (i) the fluorescent dye coumarin 153 (C153) and (ii) hemin (hem) molecules catalyzing the luminol reaction enabling chemiluminescence (CL) detection. Additionally, (iii) NP labeling with hemin-based microperoxidase MP11 was assessed. For each amplification approach, the PSP was first systematically optimized regarding size, loading concentration, and surface chemistry. Then, for an immunoassay for the inflammation marker C-reactive protein (CRP), the analyte sensitivity achievable with optimized PSP systems was compared with the established ELISA concept for photometric and CL detection. Careful optimization led to a limit of detection (LOD) of 0.1 ng/mL for MP11-labeled PSP and CL detection, performing similarly well to a photometric ELISA (0.13 ng/mL), which demonstrates the huge potential of our novel assay concept.

Highly Sensitive Microarray Immunoassay for Multiple Mycotoxins on Engineered 3D Porous Silicon SERS Substrate with Silver Nanoparticle Magnetron Sputtering

A high-throughput, rapid, and highly sensitive surface-enhanced Raman spectroscopy (SERS) microarray for screening multiple mycotoxins has been developed on a three-dimensional silver nanoparticle porous silicon (3D AgNP-Psi) SERS substrate, which was easy to be engineered by electrochemical etching and magnetron sputtering technology. The etching current density, etching waveform, and target material for magnetron sputtering have been investigated to obtain an optimal 3D SERS substrate. The optimized 3D AgNP-Psi SERS substrate showed an enhancement factor of 2.3 × 107 at 400 mA/cm2 constant current density etching for 20 s and Ag target magnetron sputtering for 200 nm thickness on the surface of Psi. The simulation electric field distribution showed the near-field enhancement can reach 3× higher than that of AuNPs. A protein microarray has been designed to screen multiple mycotoxins by AuNP Raman tags and a competitive immunoassay protocol on the surface of the 3D SERS substrate. The SERS protein microarray displayed wide linear detection ranges of 0.001-100 ng/mL for ochratoxin A, 0.01-100 ng/mL for aflatoxin B1, 0.001-10 ng/mL for deoxynivalenol, along with pg/mL low limit of detection, good recovery rates, repeatability, and reproducibility. The 3D SERS protein microarray is easily engineered and has a great potential application in medicine, environment, and food industry fields.

Magnetic-encoded fluorescent nanospheres-based competitive immunoassay for near-simultaneous detection of four mycotoxins in wheat

Simultaneous detection of mycotoxins is important for food safety. In this study, a magnetic-encoded fluorescent nanosphere-based competitive immunosensor (cFMEIS) with 2×2 array was first developed for simultaneous detection of aflatoxin B1 (AFB1), ochratoxin (OTA), deoxynivalenol (DON), and zearalenone (ZEN) in wheat. Specifically, magnetic nanoparticles with strong and weak responses were conjugated with mycotoxin antigens as capture probes. Fluorescent nanoparticles doped with europium ion (Eu3+) and terbium ion (Tb3+) with red and green emission were coupled with mycotoxin antibodies as signal probes. Using a magnetic field, immune complexes were sequentially separated in a complex system and fluorescently detected. The detection limits of AFB1, DON, OTA, and ZEN were 0.032, 0.141, 0.097, and 0.376 μg/kg, respectively. The recoveries in the certified reference material of wheat flour ranged from 81.6 to 120.0 %. Owing to its high accuracy, selectivity, and sensitivity, the cFMEIS shows great promise as an efficient and sensitive multitarget sensor for mycotoxins.

Innovative approaches for mycotoxin detection in various food categories

Mycotoxins (MTs), produced by filamentous fungi, represent a severe hazard to the health of humans and food safety, affecting the quality of various agricultural products. They can contaminate a wide range of foods, during any processing phase before or after harvest. Animals and humans who consume MTs-contaminated food or feed may experience acute or chronic poisoning, which may result in serious pathological consequences. Accordingly, developing rapid, easy, and accurate methods of MTs detection in food becomes highly urgent and critical as a quality control and to guarantee food safety and lower health hazards. In this review, we highlighted and discussed innovative approaches like biosensors, fluorescent polarization, capillary electrophoresis, infrared spectroscopy, and electronic noses for MT identification pointing out current challenges and future directions. The limitations, current challenges, and future directions of conventional detection methods versus innovative methods have also been highlighted and discussed.

Improvement of the sensitivity of lateral flow systems for detecting mycotoxins: Up-to-date strategies and future perspectives

Mycotoxins are dangerous human and animal health-threatening secondary fungal metabolites that can be found in various food and agricultural products. Several countries have established regulations to restrict their presence in food and agricultural products destined for human and animal consumption. Consequently, the need to develop highly sensitive and smart detection systems was recognized worldwide. Lateral flow assay possesses the advantages of easy operation, rapidity, stability, accuracy, and specificity, and it plays an important role in the detection of mycotoxins. Nevertheless, strategies to comprehensively improve the sensitivity of lateral flow assay to mycotoxins in food have rarely been highlighted and discussed. In this article, a comprehensive overview was presented on the application of lateral flow assay in mycotoxin detection in food samples by highlighting the principle of lateral flow assay, presenting a detailed discussion on various analytical performance-improvement strategies, such as the development of high-affinity recognition reagents, immunogen immobilization methods, and signal amplification. Additionally, a detailed discussion on the various signal analyzers and interpretation approaches was provided. Finally, current hurdles and future perspectives on the application of lateral flow assay in the detection of mycotoxins were discussed.

Affinity-Switchable Interaction of Biotin and Streptavidin for the Signal-ON Detection of Small Molecules

Lateral flow assay (LFA) based on gold nanoparticles (AuNPs) is a widely used analytical device for the rapid analysis of environmental hazards and biomarkers. Typically, a sandwich-type format is used for macromolecule detection, in which the appearance of a red test line indicates a positive result (Signal-ON). In contrast, small molecule detection usually relies on a competitive assay, where the absence of a test line indicates positive testing (Signal-OFF). However, such a "Signal-OFF" reading is usually detected within a narrower dynamic range and tends to generate false-negative signals at a low concentration. Moreover, inconsistent readings between macromolecule and small molecule testing might lead to misinterpretation when used by nonskilled individuals. Herein, we report a "Signal-ON" small molecule competitive assay based on the sterically modulated affinity-switchable interaction of biotin and streptavidin. In the absence of a small molecule target, a large steric hindrance can be imposed on the biotin to prevent interaction with streptavidin. However, in the presence of the small molecule target, this steric effect is removed, allowing the biotin to bind to streptavidin and generate the desired test line. In this article, we demonstrate the selective detection of two small molecule drugs, sulfonamides and trimethoprim, using this simple and modular affinity-switchable lateral flow assay (ASLFA). We believe that this affinity-switchable approach can also be adapted in drug discovery and clinical diagnosis, where the competitive assay format is always used for the rapid analysis of small molecules.

Isothermal Amplification and Hypersensitive Fluorescence Dual-Enhancement Nucleic Acid Lateral Flow Assay for Rapid Detection of Acinetobacter baumannii and Its Drug Resistance

Acinetobacter baumannii (A. baumannii) is among the main pathogens that cause nosocomial infections. The ability to rapidly and accurately detect A. baumannii and its drug resistance is essential for blocking secondary infections and guiding treatments. In this study, we reported a nucleic acid fluorescent lateral flow assay (NFLFA) to identify A. baumannii and carbapenem-resistant A. baumannii (CRAB) in a rapid and quantitative manner by integrating loop-mediated isothermal amplification (LAMP) and silica-based multilayered quantum dot nanobead tag (Si@MQB). First, a rapid LAMP system was established and optimised to support the effective amplification of two bacterial genes in 35 min. Then, the antibody-modified Si@MQB was introduced to capture the two kinds of amplified DNA sequences and simultaneously detect them on two test lines of a LFA strip, which greatly improved the detection sensitivity and stability of the commonly used AuNP-based nucleic acid LFA. With these strategies, the established LAMP-NFLFA achieved detection limits of 199 CFU/mL and 287 CFU/mL for the RecA (house-keeping gene) and blaOXA-23 (drug resistance gene) genes, respectively, within 43 min. Furthermore, the assay exhibited good repeatability and specificity for detecting target pathogens in real complex specimens and environments; thus, the proposed assay undoubtedly provides a promising and low-cost tool for the on-site monitoring of nosocomial infections.

Bio-conjugated nanoarchitectonics with dual-labeled nanoparticles for a colorimetric and fluorescent dual-mode serological lateral flow immunoassay sensor in detection of SARS-CoV-2 in clinical samples

Serological detection of antibodies for diagnosing infectious diseases has advantages in facile diagnostic procedures, thereby contributing to controlling the spread of the pathogen, such as in the recent SARS-CoV-2 pandemic. Lateral flow immunoassay (LFIA) is a representative serological antibody detection method suitable for on-site applications but suffers from low clinical accuracy. To achieve a simple and rapid serological screening as well as the sensitive quantification of antibodies against SARS-CoV-2, a colorimetric and fluorescent dual-mode serological LFIA sensor incorporating metal-enhanced fluorescence (MEF) was developed. For the strong fluorescence signal amplification, fluorophore Cy3 was immobilized onto gold nanoparticles (AuNPs) with size-controllable spacer polyethyleneglycol (PEG) to maintain an optimal distance to induce MEF. The sensor detects the target IgG with a concentration as low as 1 ng mL-1 within 8 minutes. The employment of the MEF into the dual-mode serological LFIA sensor shows a 1000-fold sensitivity improvement compared with that of colorimetric LFIAs. The proposed serological LFIA sensor was tested with 73 clinical samples, showing sensitivity, specificity, and accuracy of 95%, 100%, and 97%, respectively. In conclusion, the dual-mode serological LFIA has great potential for application in diagnosis and an epidemiological survey of vaccine efficacy and immunity status of individuals.

Microfluidic Biosensor Integrated with Signal Transduction and Enhancement Mechanism for Ultrasensitive Noncompetitive Assay of Multiple Mycotoxins

To achieve high-throughput ultrasensitive detection of mycotoxins in food, a functional DNA-guided transition-state CRISPR/Cas12a microfluidic biosensor (named FTMB) was successfully constructed. The signal transduction CRISPR/Cas12a strategy in FTMB has utilized DNA sequences with a specific recognition function and activators to form trigger switches. Meanwhile, the transition-state CRISPR/Cas12a system was constructed by adjusting the composition ratio of crRNA and activator to achieve a high response for low concentrations of target mycotoxins. On the other hand, the signal enhancement of FTMB has efficiently integrated the signal output of quantum dots (QDs) with the fluorescence enhancement effect of photonic crystals (PCs). The construction of universal QDs for the CRISPR/Cas12a system and PC films matching the photonic bandgap produced a significant signal enhancement by a factor of 45.6. Overall, FTMB exhibited a wide analytic range (10^-5-10¹ ng·mL^-1), low detection of limit (fg·mL^-1), short detection period (∼40 min), high specificity, good precision (coefficients of variation <5%), and satisfactory practical sample analysis capacity (the consistency with HPLC at 88.76%-109.99%). It would provide a new and reliable solution for the rapid detection of multiple small molecules in the fields of clinical diagnosis and food safety.

"Green" Extraction and On-Site Rapid Detection of Aflatoxin B1, Zearalenone and Deoxynivalenol in Corn, Rice and Peanut

The common mycotoxins in polluted grains are aflatoxin B1(AFB1), zearalenone (ZEN) and deoxynivalenol (DON). Because of the potential threat to humans and animals, it is necessary to detect mycotoxin contaminants rapidly. At present, later flow immunoassay (LFIA) is one of the most frequently used methods for rapid analysis. However, multistep sample pretreatment processes and organic solvents are also required to extract mycotoxins from grains. In this study, we developed a one-step and "green" sample pretreatment method without using organic solvents. By combining with LFIA test strips and a handheld detection device, an on-site method for the rapid detection of AFB1, ZEN and DON was developed. The LODs for AFB1, ZEN and DON in corn are 0.90 μg/kg, 7.11 μg/kg and 10.6 μg/kg, respectively, and the working ranges are from 1.25 μg/kg to 40 μg/kg, 20 μg/kg to 2000 μg/kg and 35 μg/kg to 1500 μg/kg, respectively. This method has been successfully applied to the detection of AFB1, ZEN and DON in corn, rice and peanut, with recoveries of 89 ± 3%-106 ± 3%, 86 ± 2%-108 ± 7% and 90 ± 2%-106 ± 10%, respectively. The detection results for the AFB1, ZEN and DON residues in certified reference materials by this method were in good agreement with their certificate values.

Development and application of lateral flow strip with three test lines for detection of deoxynivalenol in wheat

Lateral flow strip was widely used and their qualitative and quantitative performance was in continuous improvement. However, the traditional strip was in a single-test-line format, which restricted operators to making a semi-quantitative judgment around a desired threshold concentration. Herein, a single strip with three test lines (TTLS) was developed for the semi-quantitative and quantitative determination of deoxynivalenol (DON). Four visual detection thresholds were obtained under optimized conditions and 35 wheat samples with DON content from 45 µg/kg to 2841 µg/kg were used to verify the method. The detection results were compared with that of the traditional strip and UPLC-MS/MS. In a three-test-line format, TTLS could reveal at least 200, 500, 1000, and 2000 µg/kg DON existed in different samples by the naked eye. The agreement analysis and statistical results indicated the new TTLS can be used as a useful tool for quantitative detection of DON with wide dynamic range.

Establishment and application of multiple immunoassays for environmental estrogens based on recombinant Japanese flounder (Paralichthys olivaceus) choriogenin protein

Environmental estrogens have generated great concern because of their potential threat to aquatic organisms; however, the commonly used vitellogenin (Vtg) biomarker detection methods are not capable of detecting estrogenic activity below 10 ng/L 17β-estradiol. In this study, we developed multiple immunoassays based on Japanese flounder (Paralichthys olivaceus) choriogenin (Chg), a highly sensitive biomarker of environmental estrogens. Chg genes (ChgL and ChgH) of Japanese flounder were cloned for the first time, and a recombinant ChgL protein with a molecular weight of approximately 52 kDa was prepared using a prokaryotic expression system and purified using Ni-affinity column chromatography. Subsequently, specific monoclonal antibodies against ChgL were prepared and used to develop sandwich enzyme-linked immunosorbent assays (ELISAs), which had a detection range of 3.9-250 ng/mL and detection limit of 1.9 ng/mL. An immunofluorescence method was also established and used to visually detect ChgL induction in the tissues. In addition, a lateral flow immunoassay for ChgL that could detect estrogen activity within 10 min was developed. Finally, the reliability of the immunoassays was examined by measuring ChgL induction in the plasma and tissues of Japanese flounder exposed to 0, 2, 10, and 50 ng/L 17α-ethinylestradiol (EE₂). The results showed that 2 ng/L EE₂ notably increased ChgL levels in the plasma, demonstrating that ChgL is more sensitive than Vtg to environmental estrogens; 50 ng/L EE₂ induced obvious Chg induction in the sinusoidal vessels of the liver. Conclusions taken together, this study provides reliable methods for sensitive and rapid detection of estrogenic activity in aquatic environments.

Type B Trichothecenes in Cereal Grains and Their Products: Recent Advances on Occurrence, Toxicology, Analysis and Post-Harvest Decontamination Strategies

Type B trichothecenes (deoxynivalenol, nivalenol, 3-acetyldeoxynivalenol, 15-acetyldeoxynivalenol) and deoxynivalenol-3-glucoside (DON-3G) are secondary toxic metabolites produced mainly by mycotoxigenic Fusarium fungi and have been recognized as natural contaminants in cereals and cereal-based foods. The latest studies have proven the various negative effects of type B trichothecenes on human health. Due to the widespread occurrence of Fusarium species, contamination by these mycotoxins has become an important aspect for public health and agro-food systems worldwide. Hence, their monitoring and surveillance in various foods have received a significant deal of attention in recent years. In this review, an up-to-date overview of the occurrence profile of major type B trichothecenes and DON-3G in cereal grains and their toxicological implications are outlined. Furthermore, current trends in analytical methodologies for their determination are overviewed. This review also covers the factors affecting the production of these mycotoxins, as well as the management strategies currently employed to mitigate their contamination in foods. Information presented in this review provides good insight into the progress that has been achieved in the last years for monitoring type B trichothecenes and DON-3G, and also would help the researchers in their further investigations on metabolic pathway analysis and toxicological studies of these Fusarium mycotoxins.

Chromatographic methods for rapid aflatoxin B1 analysis in food: a review

Aflatoxin B1 (AFB1) is a mycotoxin and is the most carcinogenic of all known chemicals. In view of the AFB1 characteristics of widespread distribution, serious pollution, great harm to humans, and animals and difficult to remove, it is urgent to develop a convenient and sensitive detection method. Moreover, chromatographic test strips (CTSs) are a rapid detection technology that combines labeling technology with chromatography technology. CTSs have been widely used in the fields of environmental monitoring, medical diagnosis, and food safety analysis in recent years. Different from other immune assays, they have the advantages of short measuring time, low cost, high efficiency and no need for professionals to operate. In addition, the introduction of nanomaterials has laid a good foundation for the detection of high sensitivity, high specificity and high efficiency via CTSs. Herein, we tend to comprehensively introduce the applications of chromatographic methods in AFB1 detection and pay attention to the signal detection modes based on nanomaterials in antibody-based immunochromatographic strips (ICSs), such as colorimetric, fluorescent, chemiluminescent, and Raman scattering sensing. Some typical examples are also listed in this review. In the end, we make a summary and put forward prospects for the development of CTSs.

Using an ultra-compact optical system to improve lateral flow immunoassay results quantitatively

The lateral flow immunoassay (LFIA) is a paper-based platform with extensive application in point-of-care (POC) testing and many fields. However, its clinical application is severely limited due to the lack of quantitative ability of standard LFIA tests; this augmentation provides the system with quantifying the signal from magenta-colored AuNPs. To address this issue, we proposed an ultra-compact optical system that allowed LFIAs to be performed more accurately and objectively. The experimental setup consisted of multiple optical accessories manufactured by 3D printing (STEP files were included). A high-resolution printer was used to print out a magenta card model for the LFIA, whose color code, ranging from 255, 255, 255 to 255, 0, 255 in the RGB (red, green, blue) format, represents different levels of magenta color intensity (from 0% to 100%) and thus the results of LFIA test strips. A mathematical model was built using a calibration curve to describe the relationship between magenta color value and reflectance spectrum. In addition, a spectrum module was integrated into the proposed system to identify and quantify LFIA results. This integration represents a pioneering step in developing portable detection techniques that facilitate quantifying LFIA results. Finally, we expect this ultra-compact optical spectroscopy system to have great potential for novel clinical applications.

Triplex Immunostrip Assay for Rapid Diagnosis of Tobacco Mosaic Virus, Tobacco Vein Banding Mosaic Virus, and Potato Virus Y

Mixed virus infection has increasingly become a problem in the production of Solanaceae crops in recent years; therefore, a fast and accurate detection method is needed. In this study, a novel triplex immunostrip assay was developed for the simultaneous detection of tobacco mosaic virus (TMV), tobacco vein banding mosaic virus (TVBMV), and potato virus Y (PVY). The limits of detection of this novel immunostrip reached 200 ppb (ng/ml), 1 ppm (µg/ml), and 2 ppm for TMV, PVY, and TVBMV particles, respectively. Importantly, no cross-reactivity was observed among TMV, TVBMV, and PVY or to a nontarget virus. When the assay was applied to suspected virus-infected tobacco, tomato, and potato samples collected from fields in Southwest China, samples of single or mixed virus infection were successfully identified. In conclusion, the triplex immunostrip assay provides a fast and easy to use on-site detection method for field epidemiological studies of TMV, TVBMV, and PVY, and for managing diseases that are caused by them.

Recent advances in simultaneous detection strategies for multi-mycotoxins in foods

Mycotoxin contamination has become a challenge in the field of food safety testing, given the increasing emphasis on food safety in recent years. Mycotoxins are widely distributed, in heavily polluted areas. Food contamination with these toxins is difficult to prevent and control. Mycotoxins, as are small-molecule toxic metabolites produced by several species belonging to the genera Aspergillus, Fusarium, and Penicillium growing in food. They are considered teratogenic, carcinogenic, and mutagenic to humans and animals. Food systems are often simultaneously contaminated with multiple mycotoxins. Due to the additive or synergistic toxicological effects caused by the co-existence of multiple mycotoxins, their individual detection requires reliable, accurate, and high-throughput techniques. Currently available, methods for the detection of multiple mycotoxins are mainly based on chromatography, spectroscopy (colorimetry, fluorescence, and surface-enhanced Raman scattering), and electrochemistry. This review provides a comprehensive overview of advances in the multiple detection methods of mycotoxins during the recent 5 years. The principles and features of these techniques are described. The practical applications and challenges associated with assays for multiple detection methods of mycotoxins are summarized. The potential for future development and application is discussed in an effort, to provide standards of references for further research.

Multiplex Lateral Flow Assay and the Sample Preparation Method for the Simultaneous Detection of Three Marine Toxins

A multiplex lateral flow immunoassay (LFA) has been developed to detect the primary marine biotoxin groups: amnesic shellfish poisoning toxins, paralytic shellfish poisoning toxins, and diarrhetic shellfish poisoning toxins. The performance characteristics of the multiplex LFA were evaluated for its suitability as a screening method for the detection of toxins in shellfish. The marine toxin-specific antibodies were class-specific, and there was no cross-reactivity between the three toxin groups. The test is capable of detecting all three marine toxin groups, with working ranges of 0.2-1.5, 2.5-65.0, and 8.2-140.3 ng/mL for okadaic acid, saxitoxin, and domoic acid, respectively. This allows the multiplex LFA to detect all three toxin groups at the EU regulatory limits, with a single sample extraction method and dilution volume. No matrix effects were observed on the performance of the LFA with mussel samples spiked with toxins. The developed LFA uses a simple and pocket-sized, portable Cube Reader to provide an accurate result. We also evaluated the use of this Cube Reader with commercially available monoplex lateral flow assays for marine toxins.

A Novel Lateral Flow Immunochromatographic Assay for Rapid and Simultaneous Detection of Aflatoxin B1 and Zearalenone in Food and Feed Samples Based on Highly Sensitive and Specific Monoclonal Antibodies

Simultaneous aflatoxin (AFB1) and zearalenone (ZEN) contamination in agro-products have become widespread globally and have a toxic superposition effect. In the present study, we describe a highly sensitive and specific dual lateral flow immunochromatographic assay (dual test strip) for rapid and simultaneous detection of AFB1 and ZEN in food and feed samples based on respective monoclonal antibodies (mAbs). Two immunogens AFB1-BSA (an AFB1 and bovine serum albumin (BSA) conjugate) and ZEN-BSA (a ZEN and BSA conjugate) were synthesized in oximation active ester (OAE) and amino glutaraldehyde (AGA). The molecular binding ratio of AFB1:BSA was 8.64:1, and that of ZEN:BSA was 17.2:1, identified by high-resolution mass spectrometry (HRMS) and an ultraviolet spectrometer (UV). The hybridoma cell lines 2A11, 2F6, and 3G2 for AFB1 and 2B6, 4D9 for ZEN were filtered by an indirect non-competitive enzyme-linked immunosorbent assay (inELISA) and an indirect competitive enzyme-linked immunosorbent assay (icELISA), respectively. As AFB1 mAb 2A11 and ZEN mAb 2B6 had the lowest 50% inhibitive concentration (IC50) and cross-reactivity (CR), they were selected for subsequent experiments. By systematically optimizing the preparation condition of gold nanoparticles (AuNPs), AuNPs-labeled mAbs, and detection condition, the visual limit of detection (LOD) of the dual test strip was 1.0 μg/L for AFB1 and 5.0 μg/L for ZEN, whereas that of the test strip reader was 0.23 μg/L for AFB1 and 1.53 μg/L for ZEN. The high reproducibility and stability of the dual test were verified using mycotoxin-spiked samples. The dual test strips were highly specific and sensitive for AFB1 and ZEN, which were validated using liquid chromatography-tandem mass spectrometry (LC-MS/MS). Thus, the proposed AFB1 and ZEN dual test strip is suitable for rapid and simultaneous detection of AFB1 and ZEN contamination in food and feed samples.

Development of a Lateral Flow Strip with a Positive Readout for the On-Site Detection of Aflatoxin B1

Aflatoxin B₁ is one of the contamination indicators for food safety monitoring. The rapid and effective assessment and determination of AFB₁ in food is of great importance to dietary safety. The lateral flow assay shows advantages in its simplicity, and rapidity, and provides a visual readout, while the available lateral flow assay for AFB₁ requires a competitive format that produces readings inversely proportional to the AFB₁ concentration, which is counterintuitive and may lead to a potential misinterpretation of the results. Herein, we developed a positive readout aptamer-based lateral flow strip (Apt-strip) for the detection of AFB₁. This Apt-strip relies on the competition between AFB₁ and fluorescein-labeled complementary DNA strands (FAM-cDNA) for affinity binding to limited aptamers against AFB₁ (AFB₁-Apt). In the absence of AFB₁, AFB₁-Apt hybridizes with FAM-cDNA. No signal at the T-line of the Apt-strip was observed. In contrast, AFB₁-Apt binds to AFB₁ in the sample, and then a part of the FAM-cDNA is hybridized with the free AFB₁-Apt, at which time the other unreacted FAM-cDNA is captured by A35-Apt on the T-line. The signal was observed. This method achieved fast detection of AFB₁ with a detection limit (DL) of 0.1 ng/mL, positive readout, and increased sensitivity.

Deoxynivalenol fluorescence aptasensor based on AuCu bimetallic nanoclusters and MoS2

Aptamers against deoxynivalenol (DON) were selected through capture-systematic evolution of ligands by exponential enrichment. Through isothermal titration calorimetry and fluorimetric assay, aptamer candidate DN-2 demonstrated good affinity to DON with K_d value of 40.36 ± 6.32 nM. Accordingly, a Forster resonance energy transfer aptasensor was fabricated by using the aptamer DN-2 combined with AuCu bimetallic nanoclusters as energy donor and MoS₂ nanosheets as energy acceptor. Under the optimal conditions, the fluorescence response was utilized for DON quantitative determination ranging from 5 to 100 ng/mL with a detection limit of 1.87 ng/mL. The practical application of this method was verified in maize flour samples and demonstrated a satisfied recovery of 94.6 ~ 103.1%. The obtained aptamers and their application in DON determination provide a new tool for DON monitoring in various foodstuff.

The control of Fusarium growth and decontamination of produced mycotoxins by lactic acid bacteria

Global crop and food contamination with mycotoxins are one of the primary worldwide concerns, while there are several restrictions regarding approaching conventional physical and chemical mycotoxins decontamination methods due to nutrition loss, sensory attribute reduction in foods, chemical residual, inconvenient operation, high cost of equipment, and high energy consumption of some methods. In this regard, the overarching challenges of mycotoxin contamination in food and food crops require the development of biological decontamination strategies. Using certain lactic acid bacteria (LAB) as generally recognized safe (GRAS) compounds is one of the most effective alternatives due to their potential to release antifungal metabolites against various fungal factors species. This review highlights the potential applications of LAB as biodetoxificant agents and summarizes their decontamination activities against Fusarium growth and Fusarium mycotoxins released into food/feed. Firstly, the occurrence of Fusarium and the instrumental and bioanalytical methods for the analysis of mycotoxins were in-depth discussed. Upgraded knowledge on the biosynthesis pathway of mycotoxins produced by Fusarium offers new insightful ideas clarifying the function of these secondary metabolites. Moreover, the characterization of LAB metabolites and their impact on the decontamination of the mycotoxin from Fusarium, besides the main mechanisms of mycotoxin decontamination, are covered. While the thematic growth inhibition of Fusarium and decontamination of their mycotoxin by LAB is very complex, approaching certain lactic acid bacteria (LAB) is worth deeper investigations.

Highly sensitive detection of three protein toxins via SERS-lateral flow immunoassay based on SiO2@Au nanoparticles

We developed surface-enhanced Raman scattering-lateral flow immunoassay (SERS-LFIA) biosensor strips based on SiO₂@Au nanoparticles (NPs) for the specific and highly sensitive detection of ricin, staphylococcal enterotoxin B (SEB), and botulinum neurotoxin type A (BoNT/A). SiO₂@Au NPs were used to prepare SERS tags with useful properties, such as light weight, uniform particle size, good dispersion, and high SERS performance. The detection limit of the SERS-LFIA strips developed herein for ricin, SEB, and BoNT/A was 0.1, 0.05, and 0.1 ng/mL. Their sensitivity was 100-fold higher than that of colloidal gold-LFIA strips, and the same batch of strips had good repeatability. Moreover, the test was completed within 15 min, indicating that the strips are suitable for the rapid and on-site detection of the said toxins. The SERS-LFIA strips based on SiO₂@Au NPs developed herein for the detection of toxins are important to the prevention of bioterrorism attacks.

Development of Immunochromatographic Strip for Detection of αB-VxXXIVA-Conotoxin Based on 5E4 Monoclonal Antibody

Given the application of αB-VxXXIVA-conotoxin (αB-CTX) in analgesics and cancer chemotherapeutics, and its threat to humans, it is urgent to develop a rapid, effective and accurate method for the analysis and detection of αB-CTX in real shellfish and medicine drug samples. In the present study, two different immunochromatographic strips were established for αB-CTX detection, based on the monoclonal antibody 5E4 against αB-CTX, and the visual limits of detection (vLOD) for the colloidal gold nanoparticles-based strip (AuNPs-based strip) and nanoflowers-based strip (AuNFs-based strip) were 4 μg/mL and 1.5 μg/mL, respectively. The developed AuNPs-/AuNFs-based strips have good specificity and accuracy, and the detection results were analyzed in less than 10 min, without using an instrument. In view of the excellent repeatability and usability, the established methods could be applied to detect and analyze the content of αB-CTX in real samples.

Rose petals-like Bi semimetal embedded on the zeolitic imidazolate frameworks based-immunochromatographic strip to sensitively detect acetamiprid

Ultrasensitive and facile detection of Acetamiprid (ACE) is of exceptional significance to assess the environmental and biological pollution. In this study, an advanced Bi semimetal/Zeolitic imidazolate frameworks hybrid material-based immunochromatographic strip (Bi/ZIF HM-ICS) sensor was developed for the sensitive detection of ACE. The novel Bi/ZIF HM was prepared through one-pot hydrothermal reduction of Bi nanoparticles on ZIF, which was selected as a signal tag taking advantages of its excellent color intensity, strong affinity with monoclonal antibodies (mAbs), and favorable biocompatibility. Bi/ZIF HM could not only improve the utilization efficiency of mAbs but also boost the sensing performance. Under optimal conditions, the limit of detection (LOD) of the Bi/ZIF HM-ICS was 4.68 pg/mL with the linear range from 0.01 ng/mL to 6 ng/mL, which was 98-fold lower than that of traditional gold nanoparticles-based ICS (0.457 ng/mL), and the recoveries of the Bi/ZIF HM-ICS ranged from 80.27% to 118.52% with the relative standard deviation (RSD) below 3.67% in pear, apple, tomato, and cucumber. Overall, the practical application of the Bi/ZIF HM-ICS in complicated samples was realized for detecting pesticide residue, and expanding its application scope in monitoring environment.

Semi-quantitative detection of inflammatory biomarkers using a laser-patterned multiplexed lateral flow device

Inflammatory markers including C-reactive protein (CRP) and procalcitonin (PCT) have been shown to be useful biomarkers to improve triage speed and prevent the inappropriate use of antibiotics for infections such as pneumonia. Here, we present a novel and exciting solution to guide the administration of antibiotic treatment via rapid, semi-quantitative and multiplexed detection of CRP and PCT using an advanced lateral flow device (LFD) designed to have multiple parallel flow-paths, produced via the precise laser-based partitioning of the single flow-path of a standard LFD. Each flow-path within this multiplexed LFD has a unique detection capability which permits tailored detection of CRP within a predefined cut-off range (20 μg/mL - 100 μg/mL) and PCT above a pre-defined threshold (0.5 ng/mL). We demonstrate the use of this LFD in the successful detection of CRP and PCT semi-quantitatively within spiked human serum samples. This multiplexed near-patient assay has potential for development into a rapid triage and treatment of patients with suspected pneumonia.

Organic Cation Receptor for Colorimetric Lateral Flow Device: Detection of Zearalenone in Food Samples

As per the WHO reports, it has been estimated that almost 25% of food crops contain mycotoxins as the major contaminant. In this work, we developed a paper-based colorimetric lateral flow device (CLFD) impregnated with an organic cation receptor (OCR) for sensitive and selective detection of zearalenone (ZEN). Various techniques such as ultraviolet (UV)-visible absorption, cyclic voltammetry, and fluorescence spectroscopy were used for the detection of mycotoxins, and it was observed that OCR shows sensitivity and selectivity toward zearalenone (ZEN) only, irrespective of any other analytes. Furthermore, the colorimetric test revealed that the developed OCR shows a change in color with the addition of ZEN from greenish-gray to blue that is visible to the naked eye. The quantification of ZEN was also achieved using RGB analysis and compared with UV-visible spectroscopy data. Further, for the on-site detection of ZEN, a paper-based CLFD was also developed and used to evaluate the spiked corn sample containing ZEN, and it provided significant results with a limit of detection (LOD) of 0.31 nM (3σ method), good linearity (R² = 0.9702), good reproducibility (SD = ±6%, triplicate), and good recovery of ZEN of 95-102% with a variation coefficient (VC) varying from 1.56 to 4.62%. Therefore, the device has the potential to check the mycotoxin toxicity in food products and is helpful in remote and developing areas.

A monoclonal antibody-based time-resolved fluorescence microsphere lateral flow immunoassay for paclobutrazol detection

Paclobutrazol (PBZ) is a plant growth inhibitor and fungicide, but it is also carcinogenic and teratogenic, and has potential harm to human health. In this study, two PBZ haptens (PBZ-1, PBZ-2) were synthesized and conjugated with carrier proteins to get artificial antigens. A highly specific monoclonal antibody (mAb) against PBZ was prepared. The antibody subtype was IgG₁ and the concentration was 11.03 mg/mL. A sensitive and rapid time-resolved fluorescence microsphere lateral flow immunoassay (TRFMs-LFIA) was established based on the mAb. The activated pH, the mAbs diluents, the mAb reacting concentration and the probe amount were optimized. The visual limit of detection (vLOD) and quantitative limit of detection (qLOD) of the TRFMs-LFIA for PBZ were 50 and 1.72 ng/mL respectively, and the 50% inhibiting concentration (IC₅₀) was 9.38 ng/mL. The pretreatment procedures are simple and rapid, and the detection time of TRFMs-LFIA strip is 6 min. Qualitative and quantitative analysis of PBZ could be achieved under a UV light or with a portable fluorescence immunoassay analyzer. The average recovery rates ranged from 96.2% to 111.9% and the corresponding coefficients of variation (CV) were 4.0%–11.2% in spiked wheat and rice samples. Twenty real wheat and rice samples were measured by the TRFMs-LFIA and compared with Ultra-performance liquid chromatography/tandem mass spectrometry (UPLC-MS/MS). The measured values showed a good accordance. These results indicated that the proposed assay will provide a novel effective strategy for on-site detection of PBZ.

•

A new immunogen was prepared using thyroglobulin as carrier protein coupled with hapten.

•

A high-sensitivity mAb was prepared using a heterologous coating antigen.

•

Based on anti-PBZ mAb, TRAMs-LFIA was developed for the detection of paclobutrazol residue for the first time.

•

The proposed LFIA was rapid, easy to operate and highly accurate.

Sensitive and rapid determination of heat shock protein 70 using lateral flow immunostrips and upconversion nanoparticle fluorescence probes

Heat shock protein 70 (Hsp70), belonging to the heat shock protein (HSP) family, is reported to be a potential diagnostic biomarker.

A Novel Multiplex Mycotoxin Surface-Enhanced Raman Spectroscopy Immunoassay Using Functional Gold Nanotags on a Silica Photonic Crystal Microsphere Biochip

A novel multiplex mycotoxin surface-enhanced Raman spectroscopy (SERS) immunoassay was established for the first time on different artificial antigen-modified silica photonic crystal microspheres (SPCMs), which can be integrated into a biochip array to achieve multiplex detection using corresponding antibody-functionalized gold nanoparticles (AuNPs) as the SERS nanotag. The unique optical structure of SPCMs is helpful to find the detection spots easily, accommodate a large amount of probe molecules, and enhance the Raman signal intensity. Such enhancement was confirmed by the simulation result, showing the electric field enhancing effect in SPCMs with AuNPs being 7 times. A competitive SERS immunoassay was established using antigen-modified SPCMs and mycotoxins to compete for binding antibody-functionalized SERS nanotags, displaying broad linear detection ranges of 0.001-0.1 ng/mL for aflatoxin B₁ (AFB₁), 0.01-10 ng/mL for ochratoxin A (OTA), and 0.001-0.1 ng/mL for zearalenone (ZEN) and low detection limits of 0.82 pg/mL for AFB₁, 1.43 pg/mL for OTA, and 1.00 pg/mL for ZEN. In the spiked cereal samples, recovery rates of the method were measured in the range of 70.35-118.04% for the three mycotoxins, which was in agreement with that of the traditional enzyme-linked immunosorbent assay method. The SERS immunoassay for mycotoxin detection also showed high specificity and good repeatability and reproducibility. The new microsphere-based SERS immunoassay biochip only requires a one-step reaction and overcomes the disadvantages of fluorescence and chemiluminescence background signals. The work paves the way for further developing SERS-based microsphere suspension arrays for new targets.

Disposable Paper-Based Biosensors for the Point-of-Care Detection of Hazardous Contaminations-A Review

The fast detection of trace amounts of hazardous contaminations can prevent serious damage to the environment. Paper-based sensors offer a new perspective on the world of analytical methods, overcoming previous limitations by fabricating a simple device with valuable benefits such as flexibility, biocompatibility, disposability, biodegradability, easy operation, large surface-to-volume ratio, and cost-effectiveness. Depending on the performance type, the device can be used to analyze the analyte in the liquid or vapor phase. For liquid samples, various structures (including a dipstick, as well as microfluidic and lateral flow) have been constructed. Paper-based 3D sensors are prepared by gluing and folding different layers of a piece of paper, being more user-friendly, due to the combination of several preparation methods, the integration of different sensor elements, and the connection between two methods of detection in a small set. Paper sensors can be used in chromatographic, electrochemical, and colorimetric processes, depending on the type of transducer. Additionally, in recent years, the applicability of these sensors has been investigated in various applications, such as food and water quality, environmental monitoring, disease diagnosis, and medical sciences. Here, we review the development (from 2010 to 2021) of paper methods in the field of the detection and determination of toxic substances.

A fluorescent and colorimetric dual-channel sensor based on acid phosphatase-triggered blocking of internal filtration effect

A colorimetric and fluorescent dual-channel detection method for acid phosphatase (ACP) activity has been constructed, based on the internal filtering effect between oxidized 3,3',5,5'-tetramethylbenzidine (oxTMB) and rhodamine B (RB). Au³⁺, which in situ form gold nanoparticles (AuNPs), can oxidize colorless 3,3',5,5'-tetramethylbenzidine (TMB) to oxTMB (blue color). The fluorescence of RB can be quenched by oxTMB due to the spectral overlap of emission of RB and absorption of oxTMB. By means of the above process, ACP can be determined because ACP promotes the hydrolysis of 2-phospho-L-ascorbic acid trisodium salt (AAP) to generate ascorbic acid (AA), which can inhibit the internal filtering effect between RB and oxTMB. No material preparation was needed for the determination of ACP. The colorimetric and fluorimetric methods can quantify ACP in the range 0.06-5.0 mU/mL and 0.03-5.0 mU/mL, respectively. Furthermore, a smartphone-assisted sensing platform has been constructed for on-site monitoring of ACP in the range 0.75-50 mU/mL, and the detection limit is 0.3 mU/mL. The methods developed can measure ACP in human serum successfully.

Simultaneous and accurate screening of multiple genetically modified organism (GMO) components in food on the same test line of SERS-integrated lateral flow strip

Herein, a surface-enhanced Raman scattering (SERS)-integrated LFS platform was developed for rapid and simultaneous screening of multiple genetically modified organism (GMO) components (promoter, codon, and terminator) in soybean. Research demonstrated that, on the same test line (T line) of single LFS, three different GMP components can be well distinguished with the help of three SERS nano tags. Good linear correlations between SERS signal and concentration of each GMO component were also obtained for quantitative analysis. Of greater importance, whether these multiple analytes coexisted or not, varied in the same concentration trend or not, these multiple GMP components can be rapidly (15 min) and accurately screened with satisfied sensitivity and specificity by decoding the signals on the same T line. We envision that this decoding platform can further improve the potential of LFS and SERS for practical applications and provide a promising alternative for multiple screening of GMO identification in food.

Functional Micro-/Nanomaterials for Multiplexed Biodetection

When analyzing biological phenomena and processes, multiplexed biodetection has many advantages over single-factor biodetection and is highly relevant to both human health issues and advancements in the life sciences. However, many key problems with current multiplexed biodetection strategies remain unresolved. Herein, the main issues are analyzed and summarized: 1) generating sufficient signal to label targets, 2) improving the signal-to-noise ratio to ensure total detection sensitivity, and 3) simplifying the detection process to reduce the time and labor costs of multiple target detection. Then, available solutions made possible by designing and controlling the properties of micro- and nanomaterials are introduced. The aim is to emphasize the role that micro-/nanomaterials can play in the improvement of multiplexed biodetection strategies. Through analyzing existing problems, introducing state-of-the-art developments regarding relevant materials, and discussing future directions of the field, it is hopeful to help promote necessary developments in multiplexed biodetection and associated scientific research.

The Existing Methods and Novel Approaches in Mycotoxins' Detection

Mycotoxins represent a wide range of secondary, naturally occurring and practically unavoidable fungal metabolites. They contaminate various agricultural commodities like cereals, maize, peanuts, fruits, and feed at any stage in pre- or post-harvest conditions. Consumption of mycotoxin-contaminated food and feed can cause acute or chronic toxicity in human and animals. The risk that is posed to public health have prompted the need to develop methods of analysis and detection of mycotoxins in food products. Mycotoxins wide range of structural diversity, high chemical stability, and low concentrations in tested samples require robust, effective, and comprehensible detection methods. This review summarizes current methods, such as chromatographic and immunochemical techniques, as well as novel, alternative approaches like biosensors, electronic noses, or molecularly imprinted polymers that have been successfully applied in detection and identification of various mycotoxins in food commodities. In order to highlight the significance of sampling and sample treatment in the analytical process, these steps have been comprehensively described.

Polystyrene Microsphere-Based Immunochromatographic Assay for Detection of Aflatoxin B1 in Maize

Aflatoxin B1 (AFB1), a mycotoxin, is hepatotoxic, carcinogenic, and nephrotoxic in humans and animals, and contaminate a wide range of maize. In this study, an immunochromatographic assay (ICA) based on polystyrene microspheres (PMs) was developed for sensitive and quantitative detection of AFB1 in maize. The amounts of PMs, the condition for activating carboxyl groups of PMs, the amount of monoclonal antibody (mAb), and the volume of the immune probe were optimized to enhance the performance PMs-ICA for point-of-care testing of AFB1 in maize. The PMs-ICA showed the cut-off value of 1 ng/mL in phosphate buffer (PB) and 6 µg/kg in maize samples, respectively. The quantitative limit of detection (qLOD) was 0.27 and 1.43 µg/kg in PB and maize samples, respectively. The accuracy and precision of the PMs-ICA were evaluated by analysis of spiked maize samples with recoveries of 96.0% to 107.6% with coefficients of variation below 10%. In addition, the reliability of PMs-ICA was confirmed by the liquid chromatography-tandem mass spectrometry method. The results indicated that the PMs-ICA could be used as a sensitive, simple, rapid point-of-care testing of AFB1 in maize.

Simultaneous Detection of Inflammatory Biomarkers by SERS Nanotag-Based Lateral Flow Assay with Portable Cloud Raman Spectrometer

Inflammatory biomarkers are closely related to infectious diseases. However, traditional clinical tests of laboratory inspection are unable to achieve rapid and accurate detection of these biomarkers on-site due to shortcomings such as complex experimental operation, expensive equipment, and long test time. Herein, we proposed a lateral flow assay (LFA) strip based on surface-enhanced Raman scattering (SERS) nanotags (SERS-LFA strips) for the simultaneous and quantitative detection of dual infection biomarkers, serum amyloid A (SAA) and C-reactive protein (CRP), respectively. In practice, mesoporous silica (mSiO2)-coated Au nanoparticles (Au NPs) were used as the SERS substrate. Mercaptobenzoic acid (MBA) was embedded in the internal gap between Au NPs and the mSiO2 shell to prepare AuMBA@mSiO2 NPs, onto which SAA and CRP antibodies were modified to prepare two AuMBA@mSiO2 SERS nanotags. The Raman intensities of the test and control lines were simultaneously identified for the qualitative detection of SAA and CRP, with limits of detection (LODs) as low as 0.1 and 0.05 ng/mL for SAA and CRP, respectively. Finally, aiming at point-of-care testing (POCT) applications, we used a smartphone-based portable Raman spectrometer to quantitatively analyze the SERS-LFA strips. The Raman signal could still be accurately detected when the concentration of SAA and CRP was 10 ng/mL, which is lower than the LOD required in clinical practice for most diseases. Therefore, taking into account its simple operation and short analysis time, by using a portable Raman spectrometer which can be equipped with a 5G cloud-based healthcare management system, the current strategy based on SERS-LFA provides the potential for the quick and on-site diagnosis of infectious diseases such as sepsis, which is of great significance for medical guidance on the treatment of widely spread infection-related diseases in remote areas that lack well-developed medical resources.

Development of a microarray lateral flow strip test using a luminescent organic compound for multiplex detection of five mycotoxins

While lateral flow immunoassay (LFIA) is a simple technique that offers a rapid, robust, user friendly, and point-of-care test, its capacity for multiplex detection is rather limited. This study therefore combined the multiplexity of microarray technique and the simple and rapid characteristics of LFIA to enable simultaneous and quantitative detection of five mycotoxins, namely aflatoxin B1 (AFB1), deoxynivalenol (DON), fumonisin B1 (FUMB1), T-2 toxin (T-2), and zearalenone (ZON). In addition, we have synthesized a novel extra-large Stokes shift and strong fluorescence organic compound to be used as a reporter molecule which can be detected under UV light without light filter requirement. Many parameters including microarray spotting buffer, blocking buffer, and concentrations of mycotoxin antibodies were optimized for the microarray LFIA (μLFIA) construction. With the optimal conditions, the μLFIA could accurately and quantitatively detect multiple mycotoxins at the same time. The limits of detection of AFB1, DON, FUMB1, T-2, and ZON were 1.3, 0.5, 0.4, 0.4, and 0.9 ppb, respectively. The recoveries of these five mycotoxins were 70.7%-119.5% and 80.4%-124.8% for intra-assay and inter-assay, respectively. Combining the advantages of the novel reporter molecule and the multiplex capability of μLFIA test, this system could simultaneously detect multiple mycotoxins in one sample with high specificity and high sensitivity. Moreover, this system presents a promising affordable point-of-care platform to detect other analytes as well.

Recent progress in visual methods for aflatoxin detection

Aflatoxins (AFs) contamination in food and agricultural products poses a significant threat to human health. Sensitive and accurate detection of AFs provides a strong guarantee for ensuring food safety. Conventional chromatographic-based or mass spectrum methods, which rely on bulky instrument and skilled personnel, are not suitable for on-site surveillance. By contrast, visual detections which possess the merits of rapidity and sophisticated instrument-free present an excellent potential for the on-site detection of AFs. This review intends to summarize the latest development of visual methods for AFs detection, including paper-based tests, chromogenic reactions, and luminescent methods. Emerging technologies, like nanotechnology, DNAzymes, and aptamers combined with these visual methods are introduced. The basic principles, features, and application advantages of each type of visual methods are discussed. The biggest challenges and perspectives on their future trends are also addressed.

The Microbiome Meets Nanotechnology: Opportunities and Challenges in Developing New Diagnostic Devices

Monitoring of the human microbiome is an emerging area of diagnostics for personalized medicine. Here, the potential of different nanomaterials and nanobiosensing technologies is reviewed for the development of novel diagnostic devices for the detection and measurement of microbiome-related biomarkers. Moreover, the current and future landscape of microbiome-based diagnostics is defined by exploring the advantages and disadvantages of current nanotechnology-based approaches, especially in the context of developing point-of-care (PoC) devices that would meet the international guidelines known as REASSURED (Real-time connectivity; Ease of specimen collection; Affordability; Sensitivity; Specificity; User-friendliness; Rapid & robust operation; Equipment-free; and Deliverability). Finally, the strategies of the latest international scientific consortia working in this field are analyzed, the current microbiome diagnostics market are reported and the principal ethical, legal, and societal issues related to microbiome R&D and innovation are discussed.

Sensing Methodologies in Agriculture for Monitoring Biotic Stress in Plants Due to Pathogens and Pests

Reducing agricultural losses is an effective way to sustainably increase agricultural output efficiency to meet our present and future needs for food, fiber, fodder, and fuel. Our ever-improving understanding of the ways in which plants respond to stress, biotic and abiotic, has led to the development of innovative sensing technologies for detecting crop stresses/stressors and deploying efficient measures. This article aims to present the current state of the methodologies applied in the field of agriculture towards the detection of biotic stress in crops. Key sensing methodologies for plant pathogen (or phytopathogen), as well as herbivorous insects/pests are presented, where the working principles are described, and key recent works discussed. The detection methods overviewed for phytopathogen-related stress identification include nucleic acid-based methods, immunological methods, imaging-based techniques, spectroscopic methods, phytohormone biosensing methods, monitoring methods for plant volatiles, and active remote sensing technologies. Whereas the pest-related sensing techniques include machine-vision-based methods, pest acoustic-emission sensors, and volatile organic compound-based stress monitoring methods. Additionally, Comparisons have been made between different sensing techniques as well as recently reported works, where the strengths and limitations are identified. Finally, the prospective future directions for monitoring biotic stress in crops are discussed.

Rapid, simultaneous detection of mycotoxins with smartphone recognition-based immune microspheres

How to achieve simultaneous and rapid detection of various mycotoxins in food has important practical significance in the field of food processing and safety. In this paper, a smartphone immunoassay system based on hydrogel microspheres has been constructed to quickly detect two mycotoxins at the same time. The rapid detection system was reflected in the following three processes: (1) rapid separation of free matter after direct competition reaction based on hydrogel solid-phase carrier particles; (2) rapid detection process based on efficient catalytic function of enzymes; (3) fast capture and analysis of images based on smartphone software. Ochratoxin A (OTA) and zearalenone (ZEN) are secondary toxic metabolites of fungi that can contaminate a wide range of foods and feeds. OTA and ZEN were used as detection model molecules to verify the feasibility of the intelligent rapid detection system. The entire detection process was within 30 min, and the results were analyzed in only 10 s. Detection limits of mycotoxins OTA and ZEN are 0.7711 ng L^-1 and 1.0391 ng L^-1. The recoveries of both mycotoxins ranged from 76.72 to 122.05%. This study provides a universal rapid detection method for on-site application of large-scale food security testing. Schematic diagram of the construction of the smartphone detection system: The system is divided into three parts: detection, image capture and analysis, and result.